MIR60363T

Technical Data Sheet 0603 Package Infrared LED MIR603Series Features ․0603 package ․Peak wavelength λp=940nm ․Package in 8mm tape on 7” diameter reel ․Compatible with infrared and vapor phase reflow solder process. ․Pb free ․The product itself will remain within RoHS compliant version. Descriptions ․The device is an infrared emitting diode in miniature SMD package which is molded in a water clear epoxy. ․The device is spectrally matched with silicon photodiode and phototransistor. Applications ․PCB mounted infrared sensor ․Optoelectronic switch ․Smoke detector ․Infrared applied system Devices Selection Guide LED Part No. Thickness Lens Color MIR60363T 0.6mm Water clear MIR60383T 0.8mm Water clear Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1 Page: 1 of 10 Device No：DIR-0000321 Prepared date：04-23-2010 Prepared by：JAINE TSAI Package Dimensions MIR60363T Notes: 1. All dimensions are in millimeters 2. Tolerances unless dimensions ±0.1mm Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1 Page: 2 of 10 Device No：DIR-0000321 Prepared date：04-23-2010 Prepared by：JAINE TSAI MIR60383T Notes: 1. All dimensions are in millimeters 2. Tolerances unless dimensions ±0.1mm Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1 Page: 3 of 10 Device No：DIR-0000321 Prepared date：04-23-2010 Prepared by：JAINE TSAI Absolute Maximum Ratings (Ta=25℃) Parameter Symbol Rating Continuous Forward Current IF 65 Units mA Reverse Voltage VR 5 V Operating Temperature Topr -40 ~ +100 ℃ Storage Temperature Tstg -40 ~ +100 ℃ Tsol 260 ℃ Pd 110 mW Soldering Temperature *1 Power Dissipation at(or below) 25℃Free Air Temperature Notes: *1:Soldering time≦5 seconds. Electro-Optical Characteristics (Ta=25℃) Parameter Radiant Intensity Peak Wavelength Spectral Bandwidth Symbol Ie λp Condition IF=20mA Min. Typ. Max. 0.4 -- IF=20mA -- 940 1.16 -- Δλ IF=20mA -- 45 -- nm VF IF=20mA VR=5V 1.2 -- 1.5 10 V IR 2θ1/2 --- IF=20mA -- 140 -- Forward Voltage Reverse Current View Angle Units mW /sr nm μA deg Bin Range of Radiant Intensity Bin Min Max A 0.40 0.83 B 0.67 1.16 Unit mW/sr Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1 Page: 4 of 10 Device No：DIR-0000321 Prepared date：04-23-2010 Prepared by：JAINE TSAI Typical Electro-Optical Characteristics Curves Fig.1 Spectral Distribution Fig.2 Forward Current vs Forward Voltage 100 4 10 IF=20mA Ta=25° C 80 3 10 60 40 2 10 20 1 10 0 0 Fig.3 Radiant Intensity vs Forward Current . 1 2 3 4 Fig.4 Relative Radiant Intensity vs. Angular Displacement Ie-Radiant Intensity(mW/sr) 10 . -20 -10 0 10 20 8 30 6 1.0 40 0.9 50 0.8 0.7 60 4 2 0 0.00 0.01 0.02 0.03 0.04 0.05 70 80 0.06 IF-Forward Current (A) 0.6 0.4 0.2 0 0.2 0.4 0.6 Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1 Page: 5 of 10 Device No：DIR-0000321 Prepared date：04-23-2010 Prepared by：JAINE TSAI Precautions For Use 1. Over-current-proof Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Shelf life in sealed bag from the bag seal date: 12 months at < 40°C and < 90% RH. 2.3 After opening the package, the LEDs must be kept at ≤ 30°C and ≤ 60%RH, and used within 168 hours. 2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time. Baking treatment is required, refer to IPC/JEDEC J-STD-033 for bake procedure or recommend the conditions : 60±5°C for 72 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1 Page: 6 of 10 Device No：DIR-0000321 Prepared date：04-23-2010 Prepared by：JAINE TSAI 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1 Page: 7 of 10 Device No：DIR-0000321 Prepared date：04-23-2010 Prepared by：JAINE TSAI Package Dimensions MIR60363T Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Carrier Tape Dimensions:(Quantity: 3000pcs/reel) MIR60363T Unit: mm Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1 Page: 8 of 10 Device No：DIR-0000321 Prepared date：04-23-2010 Prepared by：JAINE TSAI Package Dimensions MIR60383T Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Carrier Tape Dimensions:(Quantity: 3000pcs/reel) MIR60383T Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1 Page: 9 of 10 Device No：DIR-0000321 Prepared date：04-23-2010 Prepared by：JAINE TSAI Packing Procedure Label Aluminum moistue-proof bag Desiccant Label Label Form Specification CPN: Customer’s Production Number P/N : Production Number QTY: Packing Quantity CAT: Ranks HUE: Peak Wavelength REF: Reference LOT No: Lot Number MADE IN TAIWAN: Production Place Notes 1. Above specification may be changed without notice. EVERLIGHT will reserve authority on material change for above specification. 2. When using this product, please observe the absolute maximum ratings and the instructions for using outlined in these specification sheets. EVERLIGHT assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets. 3. These specification sheets include materials protected under copyright of EVERLIGHT corporation. Please don’t reproduce or cause anyone to reproduce them without EVERLIGHT’s consent. EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Tucheng, Taipei 236, Taiwan, R.O.C Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http://www.everlight.com Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1 Page: 10 of 10 Device No：DIR-0000321 Prepared date：04-23-2010 Prepared by：JAINE TSAI