PIR67-21C

Technical Data Sheet Top View LED PIR67-21C/L231/TR8 Features ․Low forward voltage. ․Compatible with infrared and vapor phase reflow solder process. ․Package in 8mm tape on 7” diameter reels. ․Size of emitting area 0.370mm * 0.370mm ․Pb free ․Typical peak wavelength 740nm ․The product itself will remain within RoHS compliant version Descriptions ․PIR67-21C/L231/TR8 is an infrared emitting diode in miniature SMD package which is molded in a water clear plastic with spherical top view lens. ․The device is spectrally matched with silicon photodiode and phototransistor. Applications ․Sensor technology ․IR free air transmission ․For drive and control circuits ․Optoelectronic switch ․Infrared applied system Device Selection Guide LED Part No. PIR67-21C/L231/TR8 Chip Material AIGaAs Epoxy color Water clear Everlight Electronics Co., Ltd. Device No http:\\www.everlight.com Prepared date Rev 3 Page: 1 of 10 DTR-067-249 06-08-2007 Prepared by Daniel Yang ： ： ： PIR67-21C/L231/TR8 Package Dimensions edoh taC edonA 1.5 1.5 1.5 Notes: 1.All dimensions are in millimeters 2.Tolerances unless dimensions ±0.1mm Absolute Maximum Ratings (Ta=25℃) Parameter Continuous Forward Current Reverse Voltage Surge current(t=10μs) Operating Temperature Storage Temperature Thermal resistance junction to ambient mounted on PC-board Thermal resistance junction to soldering point,mounted on metal block Soldering Temperature *1 Power Dissipation at(or below) 25℃Free Air Temperature *2:Soldering time≦10 seconds. Symbol IF VR IFSM Topr Tstg RthJA RthJS Tsol Pd Rating 100 5 1 -40 ~ +100 -40 ~ +100 210 260 260 190 Units mA V A ℃ ℃ K/W K/W ℃ mW Notes: : *1:IFP Conditions--Pulse Width≦100μs and Duty≦1%. Everlight Electronics Co., Ltd. Device No http:\\www.everlight.com Prepared date Rev 3 Page: 2 of 10 DTR-067-249 06-08-2007 Prepared by Daniel Yang ： ： ： PIR67-21C/L231/TR8 Electro-Optical Characteristics (Ta=25℃) Parameter Radiant Intensity Total Radiated Power Peak Wavelength Spectral Bandwidth Forward Voltage Reverse Current Rise Time Fall Time Capacitance View Angle Active chip area Dimensions of the active chip area Symbol Ie Po λp Δλ VF IR tr tf Co 2θ1/2 A L*W Condition IF=20mA IF=50mA IF=50mA IF=20mA IF=20mA IF=20mA IF=50mA VR=5V IF=50mA IF=50mA VR=0V, f=1MHz IF=20mA ----Min. -3.0 -725 --------Typ. 2.5 6.0 18 740 30 1.8 2.0 -80 80 55 120 0.140 0.370*0.370 Max. ---755 -2.2 2.8 10 ----mW nm nm V μA ns ns pF deg mm2 mm*mm Units mW/sr Everlight Electronics Co., Ltd. Device No http:\\www.everlight.com Prepared date Rev 3 Page: 3 of 10 DTR-067-249 06-08-2007 Prepared by Daniel Yang ： ： ： PIR67-21C/L231/TR8 Typical Electro-Optical Characteristics Curves Fig.1 Forward Current vs. Ambient Temperature 041 Fig.2 Spectral Distribution 100 80 60 40 20 0 IF=20mA Ta=25°C Fig.3 Peak Emission Wavelength vs. Ambient Temperature Everlight Electronics Co., Ltd. Device No DTR-067-249 Prepared date 06-08-2007 Prepared by Daniel Yang ： ： ： 021 001 02 04 08 06 0 -40 -20 0 20 40 60 80 100 120 680 700 720 740 760 780 800 820 840 Fig.4 Forward Current vs. Forward Voltage 780 100 90 80 70 60 50 40 30 20 10 0 0 25 50 75 100 760 740 720 700 -25 1.2 1.6 2.0 2.4 2.8 http:\\www.everlight.com Rev 3 Page: 4 of 10 PIR67-21C/L231/TR8 Typical Electro-Optical Characteristics Curves Fig.5 Relative Radiant Intensity vs. Angular Displacement 0 1.0 10 20 30 40 50 0.8 0.6 R elative Intensity 60 0.4 70 80 -80 -70 -60 -50 -40 -30 -20 -10 0 0.2 0.0 -90 90 Angle(Degree) Everlight Electronics Co., Ltd. Device No http:\\www.everlight.com Prepared date Rev 3 Page: 5 of 10 DTR-067-249 06-08-2007 Prepared by Daniel Yang ： ： ： PIR67-21C/L231/TR8 Precautions For Use 1. Over-current-proof Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 The LEDs should be used within a year. 2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less. 2.5 The LEDs should be used within 168 hours (7 days) after opening the package. 2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for 48 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. Everlight Electronics Co., Ltd. Device No http:\\www.everlight.com Prepared date Rev 3 Page: 6 of 10 DTR-067-249 06-08-2007 Prepared by Daniel Yang ： ： ： PIR67-21C/L231/TR8 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. Everlight Electronics Co., Ltd. Device No http:\\www.everlight.com Prepared date Rev 3 Page: 7 of 10 DTR-067-249 06-08-2007 Prepared by Daniel Yang ： ： ： PIR67-21C/L231/TR8 Reliability Test Item And Condition The reliability of products shall be satisfied with items listed below. Confidence level：90% LTPD：10% NO. Item Test Conditions Test Hours/ Sample Cycles 1 REFLOW TEMP.：260℃±5℃ 6Mins Sizes 22pcs IR≧U×2 15mins 50Cycles 5mins 15mins 5mins 50Cycles 10secs 5mins 1000hrs 1000hrs 1000hrs 1000hrs 22pcs 22pcs 22pcs 22pcs 22pcs 22pcs Ie≦L×0.8 VF≧U×1.2 U：Upper Specification Limit L：Lower Specification TEMP.：-40℃ Limit 0/1 0/1 0/1 0/1 0/1 0/1 Failure Judgement Criteria 0/1 10secs 2 Temperature Cycle H : 100℃ L : -40℃ 3 Thermal Shock H :+100℃ L :-10℃ 4 High Temperature Storage 5 Low Temperature Storage 6 DC Operating Life IF=20mA 7 High Temperature/ 85℃ / 85% R.H High Humidity Ac/Re TEMP.：+100℃ Everlight Electronics Co., Ltd. Device No http:\\www.everlight.com Prepared date Rev 3 Page: 8 of 10 DTR-067-249 06-08-2007 Prepared by Daniel Yang ： ： ： PIR67-21C/L231/TR8 Package Dimensions Taping Dimensions Unit: mm Everlight Electronics Co., Ltd. Device No http:\\www.everlight.com Prepared date Rev 3 Page: 9 of 10 DTR-067-249 06-08-2007 Prepared by Daniel Yang ： ： ： PIR67-21C/L231/TR8 Packing Quantity Specification 1.2000Pcs/1Volume，1Volume/1Bag 2.10Boxes/1Carton Label Form Specification CPN: Customer’s Production Number P/N : Production Number QTY: Packing Quantity RoHS CAT: Ranks HUE: Peak Wavelength REF: Reference LOT No: Lot Number MADE IN TAIWAN: Production Place PIR67-21C/L231/TR8 Notes 1. Above specification may be changed without notice. EVERLIGHT will reserve authority on material change for above specification. 2. When using this product, please observe the absolute maximum ratings and the instructions for using outlined in these specification sheets. EVERLIGHT assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets. 3. These specification sheets include materials protected under copyright of EVERLIGHT corporation. Please don’t reproduce or cause anyone to reproduce them without EVERLIGHT’s consent. EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Tucheng, Taipei 236, Taiwan, R.O.C Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http:\\www.everlight.com Everlight Electronics Co., Ltd. Device No http:\\www.everlight.com Prepared date Rev 3 Page: 10 of 10 DTR-067-249 06-08-2007 Prepared by Daniel Yang ： ： ：