PT57-21B/TR8

Technical Data Sheet Side Looking Silicon PIN Photodiode PT57-21B/TR8 Features ․Fast response time ․High photo sensitivity ․Small junction capacitance ․Compatible with infrared and vapor phase reflow solder process. ․Pb free ․The product itself will remain within RoHS compliant version. Descriptions ․PT57-21B/TR8 is a high speed silicon NPN epitaxial planar phototransistor in a compact surface-mountable package. It’s compatible with automatic placement equipment and can withstand IR reflow, vapor phase reflow , and wave solder processes. Applications ․Miniature switch ․Counters and sorter ․Position sensor ․Infrared applied system Device Selection Guide Revision LED Part No. Chip Material Lens Color PT57-21B/TR8 Silicon Black Everlight Electronics Co., Ltd. http://www.everlight.com Device No：DIR-0000252 Prepared date：09-08-2010 :2 LifecyclePhase: Rev 2 Page: 1 of 9 Prepared by：Daniel Yang Release Date:2010-09-10 13:21:48.0 Expired Period: Forever PT57-21B/TR8 Package Dimensions Emitter Collector Notes: 1.All dimensions are in millimeters 2.Tolerances unless dimensions ±0.1mm Absolute Maximum Ratings (Ta=25℃) Parameter Symbol Rating Unit Collector-Emitter Voltage VCEO 30 Emitter-Collector-Voltage VECO 5 V V IC 20 mA Operating Temperature Topr -25 ~ +85 ℃ Storage Temperature Tstg -40 ~ +85 ℃ Soldering Temperature Tsol 260 ℃ Power Dissipation at(or below) 25℃Free Air Temperature Pc 75 mW Collector Current Notes: *1:Soldering time≦5 seconds. Revision Everlight Electronics Co., Ltd. http://www.everlight.com Device No：DIR-0000252 Prepared date：09-08-2010 :2 LifecyclePhase: Rev 2 Page: 2 of 9 Prepared by：Daniel Yang Release Date:2010-09-10 13:21:48.0 Expired Period: Forever PT57-21B/TR8 Electro-Optical Characteristics (Ta=25℃) Parameter Symbol Condition Min Typ Max Unit Rang Of Spectral Bandwidth λ0.5 --- 700 --- 1100 nm Wavelength Of Peak Sensitivity λP --- --- 940 --- nm Collector-Emitter Breakdown Voltage BVCEO IC=100μA Ee=0mW/cm2 30 --- --- V Emitter-Collector Breakdown Voltage BVECO 5 --- --- V Collector-Emitter Saturation Voltage VCE(sat) IC=0.1mA Ee=1m W/cm2 --- --- 0.4 V Collector Dark Current ICEO VCE=20V Ee=0mW/cm2 --- --- 100 nA On State Collector Current IC(ON) VCE=5V Ee=1mW /cm2 0.4 0.8 --- mA --- 15 --- --- 15 --- Rise Time tr Fall Time tf Revision IE=100μA Ee=0mW/cm2 VCE=5V IC=1mA RL=1000Ω Everlight Electronics Co., Ltd. http://www.everlight.com Device No：DIR-0000252 Prepared date：09-08-2010 :2 LifecyclePhase: μS Rev 2 Page: 3 of 9 Prepared by：Daniel Yang Release Date:2010-09-10 13:21:48.0 Expired Period: Forever PT57-21B/TR8 Typical Electro-Optical Characteristics Curves Fig.1Collector Power Dissipation vs. Ambient Temperature Fig.2 Spectral Sensitivity 1.0 100 O Ta=25 C 80 0.8 60 0.6 40 0.4 20 0.2 0 0 -25 25 0 50 75 85 100 Fig.3 Relative Collector Current vs. Ambient Temperature 600 700 800 900 1000 1100 1200 Fig.4 Collector Current vs. Irradiance 100 160 C 2 140 10 120 100 1 80 60 0.1 40 20 0 0 10 20 30 40 50 60 70 0.01 0.01 0.1 1 10 2 Revision Everlight Electronics Co., Ltd. http://www.everlight.com Device No：DIR-0000252 Prepared date：09-08-2010 :2 LifecyclePhase: Rev 2 Page: 4 of 9 Prepared by：Daniel Yang Release Date:2010-09-10 13:21:48.0 Expired Period: Forever PT57-21B/TR8 Typical Electro-Optical Characteristics Curves Fig.5 Collector Dark Current vs. Ambient Temperature 10 10 10 10 10 0 Revision 25 50 75 100 Everlight Electronics Co., Ltd. http://www.everlight.com Device No：DIR-0000252 Prepared date：09-08-2010 :2 LifecyclePhase: Rev 2 Page: 5 of 9 Prepared by：Daniel Yang Release Date:2010-09-10 13:21:48.0 Expired Period: Forever PT57-21B/TR8 Precautions For Use 1. Over-current-proof Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 The LEDs should be used within a year. 2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less. 2.5 The LEDs should be used within 168 hours (7 days) after opening the package. 2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. Revision Everlight Electronics Co., Ltd. http://www.everlight.com Device No：DIR-0000252 Prepared date：09-08-2010 :2 LifecyclePhase: Rev 2 Page: 6 of 9 Prepared by：Daniel Yang Release Date:2010-09-10 13:21:48.0 Expired Period: Forever PT57-21B/TR8 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. Revision Everlight Electronics Co., Ltd. http://www.everlight.com Device No：DIR-0000252 Prepared date：09-08-2010 :2 LifecyclePhase: Rev 2 Page: 7 of 9 Prepared by：Daniel Yang Release Date:2010-09-10 13:21:48.0 Expired Period: Forever PT57-21B/TR8 Package Dimensions Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Carrier Tape Dimensions: Loaded quantity 500 PCS per reel Emitter Collector Unit:mm Revision Everlight Electronics Co., Ltd. http://www.everlight.com Device No：DIR-0000252 Prepared date：09-08-2010 :2 LifecyclePhase: Rev 2 Page: 8 of 9 Prepared by：Daniel Yang Release Date:2010-09-10 13:21:48.0 Expired Period: Forever PT57-21B/TR8 Packing Procedure Aluminum moistue-proof bag Label Desiccant Label Label Form Specification Pb CPN: Customer’s Production Number P/N : Production Number QTY: Packing Quantity CAT: Ranks HUE: Peak Wavelength REF: Reference LOT No: Lot Number MADE IN TAIWAN: Production Place EVERLIGHT CPN : P N : XXXXXXXXXXXXX RoHS XXXXXXXXXXXXX QTY : XXX CAT : XXX HUE : XXX REF : XXX LOT NO : XXXXXXXXXX Reference : XXXXXXXX Notes 1. Above specification may be changed without notice. EVERLIGHT will reserve authority on material change for above specification. 2. When using this product, please observe the absolute maximum ratings and the instructions for using outlined in these specification sheets. EVERLIGHT assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets. 3. These specification sheets include materials protected under copyright of EVERLIGHT corporation. Please don’t reproduce or cause anyone to reproduce them without EVERLIGHT’s consent. EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Tucheng, Taipei 236, Taiwan, R.O.C Revision Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http://www.everlight.com Everlight Electronics Co., Ltd. http://www.everlight.com Device No：DIR-0000252 Prepared date：09-08-2010 :2 LifecyclePhase: Rev 2 Page: 9 of 9 Prepared by：Daniel Yang Release Date:2010-09-10 13:21:48.0 Expired Period: Forever