QTLP630C2TR

QTLP630C-2 HER QTLP630C-3 Yellow QTLP630C-4 Green QTLP630C-7 AlGaAs Red QTLP630C-B Blue Surface Mount LED Lamp, Standard Bright 0805 Features Applications ■ Small footprint – 2.0(L) X 1.25(W) X 1.1(H) mm ■ Keypad backlighting ■ Wide viewing angle of 140° ■ Push-button backlighting ■ Water clear optics ■ LCD backlighting ■ Moisture-proof packaging Description ■ Available in 0.315” (8mm) width tape on 7” (178mm) diameter reel; 2,000 units per reel These surface mount chip LEDs are designed to fit industry standard footprint. Low profile and wide viewing angle make these LEDs ideal choices for backlighting applications and panel illumination. Package Dimensions 0.087 (2.2) 0.071 (1.8) R0.008 (0.2) 0.057 (1.45) 0.041 (1.05) TOP POLARITY MARK (See Note 2) 0.012 (0.3) 2X 0.055 (1.4) 0.047 (1.2) 0.041 (1.05) 0.024 (0.6) SIDE 0.016 (0.4) 2X 0.047 (1.2) BOTTOM + - for -2, -3, -4 and -B for -7 POLARITY NOTE: 1. Dimensions for all drawings are in inches (mm). 2. Cathode for -2, -3, -4 and B. Anode for -7. ©2005 Fairchild Semiconductor Corporation QTLP630C-X Rev. 1.0.0 1 www.fairchildsemi.com QTLP630C-X Surface Mount LED Lamp, Standard Bright 0805 November 2005 QTLP630C Parameter Symbol -2 -3 -4 -7 -B Unit IF 30 30 30 30 30 mA Peak Forward Current (f = 1.0 KHz, Duty Factor = 1/10) IFM 160 160 160 180 100 mA Reverse Voltage (IR = 10 µA) VR 5 5 5 5 5 V Power Dissipation PD 84 84 84 72 135 mW Continuous Forward Current -40 to +85 °C TSTG -40 to +90 °C TSOL 260 for 5 sec °C Operating Temperature TOPR Storage Temperature Lead Soldering Time Electrical/Optical Characteristics (TA = 25°C) QTLP630C Parameter Symbol -2 -3 -4 -7 -B Condition IV 5 5 6 10 15 IF = 20mA 10 10 10 20 20 2.8 2.8 2.8 2.4 4.5 2.0 2.0 2.1 1.9 3.8 Luminous Intensity (mcd) Minimum Typical Forward Voltage (V) Maximum VF Typical IF = 20mA Wavelength (nm) Peak λP 635 585 565 660 430 Dominant λD 630 590 570 645 465 ∆λ 45 35 30 20 65 IF = 20mA 2Θ1/2 140 140 140 140 140 IF = 20mA Spectral Line Half Width (nm) Viewing Angle (°) 2 QTLP630C-X Rev. 1.0.0 IF = 20mA www.fairchildsemi.com QTLP630C-X Surface Mount LED Lamp, Standard Bright 0805 Absolute Maximum Ratings (TA = 25°C unless otherwise specified) Fig. 2 Relative Luminous Intensity vs. DC Forward Current Fig. 1 Forward Current vs. Forward Voltage 2.0 90 RELATIVE LUMNOUS INTENSITY (NORMALIZED AT 20 mA) IF - FORWARD CURRENT (mA) 80 70 HER 60 GREEN AlGaAs RED 50 YELLOW 40 30 BLUE 20 10 AlGaAs RED 1.5 1.0 BLUE HER YELLOW GREEN 0.5 0.0 0 1.0 2.0 2.5 3.0 4.0 5.0 0 5 10 15 20 25 30 IF - DC FORWARD CURRENT (mA) VF - FORWARD VOLTAGE (V) Fig. 3 Relative Intensity vs. Peak Wavelength HER BLUE GREEN YELLOW AlGaAs RED RELATIVE INTENSITY 1.0 0.5 0 300 350 400 450 500 550 600 650 700 750 WAVELENGTH (nm) Fig.5 Maximum Forward Current vs. Ambient Temperature IF - FORWARD CURRENT (mA) 50 Fig.4 Radiation Diagram -30˚ -20˚ -10˚ 0˚ 10˚ 20˚ 30˚ -40˚ 40˚ -50˚ 50˚ -60˚ 60˚ -70˚ 70˚ -80˚ -90˚ 1.0 40 30 20 10 80˚ 0.8 0.6 0.4 0.2 0 0.2 0.4 0.6 0.8 1.0 0 90˚ 0 40 60 80 100 TA - AMBIENT TEMPERATURE (˚C) REL. LUMINOUS INTENSITY (%) 3 QTLP630C-X Rev. 1.0.0 20 www.fairchildsemi.com QTLP630C-X Surface Mount LED Lamp, Standard Bright 0805 Typical Performance Curves 0.035 (0.9) 0.047 (1.2) 0.047 (1.2) 2X Recommended IR Reflow Soldering Profile 5 sec MAX soldering time 260° C MAX +5° C/s MAX -5° C/s MAX 120 sec Max Preheating 180 – 200°C 1 - 5° C/Sec 4 QTLP630C-X Rev. 1.0.0 www.fairchildsemi.com QTLP630C-X Surface Mount LED Lamp, Standard Bright 0805 Recommended Printed Circuit Board Pattern QTLP630C-X Surface Mount LED Lamp, Standard Bright 0805 Tape and Reel Dimensions 8.4 +1.5 -0.0 11.0 5 ±0. +0.5 -0.0 Ø62.0±0.5 2.5 0± 0.5 Ø180±1 2.5 Ø12.75 +0.25 -0.0 4.0 Ø1.55.±05 0.25±0.1 2.39±0.05 2.0±0.05 8.0 3.5±0.05 1.75 Progressive direction 1.27 4.0 for -7 1.63 for -2, -3, -4 and -B Polarity Dimensional tolerance is ± 0.1mm unless otherwise specified Angle: ± 0.5 Unit: mm 5 QTLP630C-X Rev. 1.0.0 www.fairchildsemi.com The following are registered and unregistered trademarks Fairchild Semiconductor owns or is authorized to use and is not intended to be an exhaustive list of all such trademarks. ACEx™ FAST® ActiveArray™ FASTr™ Bottomless™ FPS™ Build it Now™ FRFET™ CoolFET™ GlobalOptoisolator™ CROSSVOLT™ GTO™ DOME™ HiSeC™ EcoSPARK™ I2C™ 2 E CMOS™ i-Lo™ EnSigna™ ImpliedDisconnect™ FACT™ IntelliMAX™ FACT Quiet Series™ Across the board. Around the world.™ The Power Franchise® Programmable Active Droop™ ISOPLANAR™ LittleFET™ MICROCOUPLER™ MicroFET™ MicroPak™ MICROWIRE™ MSX™ MSXPro™ OCX™ OCXPro™ OPTOLOGIC® OPTOPLANAR™ PACMAN™ POP™ Power247™ PowerEdge™ PowerSaver™ PowerTrench® QFET® QS™ QT Optoelectronics™ Quiet Series™ RapidConfigure™ RapidConnect™ µSerDes™ ScalarPump™ SILENT SWITCHER® SMART START™ SPM™ Stealth™ SuperFET™ SuperSOT™-3 SuperSOT™-6 SuperSOT™-8 SyncFET™ TinyLogic® TINYOPTO™ TruTranslation™ UHC™ UltraFET® UniFET™ VCX™ Wire™ DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. LIFE SUPPORT POLICY FAIRCHILDíS PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 2. A critical component is any component of a life 1. Life support devices or systems are devices or support device or system whose failure to perform can systems which, (a) are intended for surgical implant into be reasonably expected to cause the failure of the life the body, or (b) support or sustain life, or (c) whose support device or system, or to affect its safety or failure to perform when properly used in accordance with instructions for use provided in the labeling, can be effectiveness. reasonably expected to result in significant injury to the user. PRODUCT STATUS DEFINITIONS Definition of Terms Datasheet Identification Product Status Definition Advance Information Formative or In Design This datasheet contains the design specifications for product development. Specifications may change in any manner without notice. Preliminary First Production This datasheet contains preliminary data, and supplementary data will be published at a later date. Fairchild Semiconductor reserves the right to make changes at any time without notice in order to improve design. No Identification Needed Full Production This datasheet contains final specifications. Fairchild Semiconductor reserves the right to make changes at any time without notice in order to improve design. Obsolete Not In Production This datasheet contains specifications on a product that has been discontinued by Fairchild semiconductor. The datasheet is printed for reference information only. Rev. I17 6 QTLP630C-X Rev. 1.0.0 www.fairchildsemi.com QTLP630C-X Surface Mount LED Lamp, Standard Bright 0805 TRADEMARKS