搜索历史

清空
搜索热词
      0
      VIP于 到期 续费
      登录后你可以
      • 下载海量资料
      • 学习在线课程
      • 观看技术视频
      • 写文章/发帖/加入社区
      会员中心
      创作中心
      发布

      • 发文章

      • 发资料

      • 发帖

      • 提问

      • 发视频

      创作活动

      电子元件查询网

      查Datasheet、查价格、查替代料
      一键BOM配单
      • 热搜：
      XR16V554IV

      XR16V554IV

      • 厂商：

        EXAR(艾科嘉)

      • 封装：

      • 描述：

        XR16V554IV - 2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO - Exar Corporation

      数据手册：

      下载XR16V554IV.pdf
      立即购买
        • 数据手册
        • 价格&库存
        XR16V554IV 数据手册
        XR16V554/554D 2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO SEPTEMBER 2007 REV. 1.0.2 GENERAL DESCRIPTION The XR16V554 (V554) is a quad Universal Asynchronous Receiver and Transmitter (UART) with 16 bytes of transmit and receive FIFOs, selectable receive FIFO trigger levels and data rates of up to 4 Mbps at 3.3 V. Each UART has a set of registers that provide the user with operating status and control, receiver error indications, and modem serial interface controls. An internal loopback capability allows onboard diagnostics. The V554 is available in a 48pin QFN, 64-pin LQFP, 68-pin PLCC and 80-pin LQFP packages. The 64-pin and 80-pin packages only offer the 16 mode interface, but the 48- and 68pin packages offer an additional 68 mode interface which allows easy integration with Motorola processors. The XR16V554IV (64-pin) offers three state interrupt output while the XR16V554DIV provides continuous interrupt output. The XR16V554 is compatible with the industry standard ST16C554. FEATURES • Pin-to-pin compatible with ST16C454, ST16C554, TI’s TL16C554A and Philip’s SC16C554B • Intel or Motorola Data Bus Interface select • Four independent UART channels ■ ■ Register Set Compatible to 16C550 Data rates of up to 4 Mbps at 3.3 V and 3.125 Mbps at 2.5 V 16 byte Transmit FIFO 16 byte Receive FIFO with error tags 4 Selectable RX FIFO Trigger Levels Full modem interface ■ ■ ■ ■ • 2.25V to 3.6V supply operation • Crystal oscillator or external clock input APPLICATIONS • Portable Appliances • Telecommunication Network Routers • Ethernet Network Routers • Cellular Data Devices • Factory Automation and Process Controls FIGURE 1. XR16V554 BLOCK DIAGRAM * 5 Volt Tolerant Inputs ( Except XTAL1 input) UART Channel A UART 16 Byte TX FIFO Regs TX & RX BRG 16 Byte RX FIFO TXB, RXB, DTRB#, DSRB#, RTSB#, CTSB#, CDB#, RIB# TXC, RXC, DTRC#, DSRC#, RTSC#, CTSC#, CDC#, RIC# TXD, RXD, DTRD#, DSRD#, RTSD#, CTSD#, CDD#, RID# XTAL1 XTAL2 2.25V to 3.6 V VCC GND A2:A0 D7:D0 IOR# IOW# CSA# CSB# CSC# CSD# INTA INTB INTC INTD TXRDY# A-D RXRDY# A-D Reset 16/ 68# INTSEL TXA, RXA, DTRA#, DSRA#, RTSA#, CTSA#, CDA#, RIA# Data Bus Interface UART Channel B (same as Channel A) UART Channel C (same as Channel A) UART Channel D (same as Channel A) Crystal Osc / Buffer 554BLK Exar Corporation 48720 Kato Road, Fremont CA, 94538 • (510) 668-7000 • FAX (510) 668-7017 • www.exar.com XR16V554/554D 2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO REV. 1.0.2 FIGURE 2. PIN OUT ASSIGNMENT FOR 68-PIN PLCC PACKAGES IN 16 AND 68 MODE AND 64-PIN LQFP PACKAGES INTSEL CDA# RIA# CDD# CDA# RID# GND VCC RXD RXA D7 D6 D5 D4 D3 D2 D1 D0 68 67 66 65 64 63 62 RID# GND RIA# RXA 68 67 66 65 64 63 62 63 9 8 7 6 5 4 3 2 1 DSRA# CTSA# DTRA# VCC RTSA# INTA CSA# TXA IOW# TXB CSB# INTB RTSB# GND DTRB# CTSB# DSRB# 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 60 59 58 57 56 55 DSRD# CTSD# DTRD# GND RTSD# INTD CSD# TXD IOR# TXC CSC# INTC RTSC# VCC DTRC# CTSC# DSRC# DSRA# CTSA# DTRA# VCC RTSA# IRQ# CS# TXA R/W# TXB A3 N.C. RTSB# GND DTRB# CTSB# DSRB# 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 63 9 8 7 6 5 4 3 2 1 CDD# GND VCC RXD D7 D6 D5 D4 D3 D2 D1 D0 60 59 58 57 56 55 DSRD# CTSD# DTRD# GND RTSD# N.C. N.C. TXD N.C. TXC A4 N.C. RTSC# VCC DTRC# CTSC# DSRC# XR16V554 68-pin PLCC Intel Mode (16/68# pin connected to VCC) 54 53 52 51 50 49 48 47 46 45 44 XR16V554 68-pin PLCC Motorola Mode (16/68# pin connected to GND) 54 53 52 51 50 49 48 47 46 45 44 16/68# TXRDY# CDB# RXRDY# RESET XTAL1 XTAL2 TXRDY# 16/68# RXRDY# RESET XTAL1 XTAL2 CDC# 60 56 54 52 64 62 61 59 57 55 51 58 53 50 DSRA# CTSA# DTRA# VCC RTSA# INTA CSA# TXA IOW# TXB CSB# INTB RTSB# GND DTRB# CTSB# 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 21 29 23 22 25 26 27 28 30 31 17 20 18 19 24 32 63 49 CDD# CDA# GND RXD RID# RXA RIA# D6 D5 D4 D3 D1 D0 VCC D7 D2 48 47 46 45 44 43 DSRD# CTSD# DTRD# GND RTSD# INTD CSD# TXD IOR# TXC CSC# INTC RTSC# VCC DTRC# CTSC# XR16V554/554D 64-pin TQFP Intel Mode Only 42 41 40 39 38 37 36 35 34 33 RIB# DSRB# CDB# CDC# RIC# A1 A0 RESET 2 DSRC# A2 XTAL1 XTAL2 RXB GND VCC RXC CDC# CDB# RIC# GND RIB# RIC# RIB# GND RXB VCC VCC RXC RXC A2 A1 RXB A2 A1 A0 A0 XR16V554/554D REV. 1.0.2 2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO FIGURE 3. PIN OUT ASSIGNMENT FOR 48-PIN QFN PACKAGE AND 80-PIN LQFP PACKAGE 38 INTSEL 47 GND 47 GND 38 INTSEL 37 VCC 39 D0 46 D7 45 D6 44 D5 46 D7 45 D6 42 44 D5 48 48 CTSA# VCC RTSA# INTA CSA# TXA IOW# TXB CSB# INTB RTSB# CTSB# 1 2 3 4 5 6 7 8 9 10 11 12 21 15 18 19 20 22 23 13 14 16 17 24 36 35 34 33 RXD CTSD# GND RTSD# INTD 42 39 D0 37 VCC RXA 40 D1 RXA 43 D4 43 D4 41 D2 41 D2 40 D1 D3 D3 CTSA# VCC RTSA# INTA CSA# TXA IOW# TXB CSB# INTB RTSB# CTSB# 1 2 3 4 5 6 7 8 9 10 11 12 15 18 19 20 21 22 13 14 16 17 23 24 36 35 34 33 RXD CTSD# GND RTSD# INTD XR16V554 48-pin QFN Intel Mode (16/68# pin connected to VCC) 32 31 CSD# 30 29 28 27 26 25 TXD IOR# TXC CSC# INTC RTSC# XR16V554 48-pin QFN Motorola Mode (16/68# pin connected to GND) 32 31 CSD# 30 29 28 27 26 25 TXD IOR# TXC CSC# INTC RTSC# RESET RESET XTAL1 XTAL1 16/68# 16/68# RXB GND RXB XTAL2 XTAL2 GND A1 RXC VCC A1 RXC CTSC# DSRD# DTRD# CTSD# RTSD# CTSC# RTSC# INTD GND DTRC# NC NC DSRC# CSD# IOR# CSC# INTC VCC TXD TXC 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 NC CDD# RID# 1 2 3 61 NC 60 59 58 57 56 NC CDC# RIC# RXC GND TXRDY# RXRDY# RESET NC XTAL2 XTAL1 NC A0 A1 A2 VCC RXB RIB# CDB# NC RXD VCC INTSEL D0 D1 D2 NC D3 D4 D5 D6 D7 GND RXA RIA# CDA# NC 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 55 54 53 XR16 V 554 80 - pin LQFP Intel Mode Only 52 51 50 49 48 47 46 45 44 43 42 41 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 DTRA # CTSA# RTSA# RTSB# CSA# IOW# CSB# DTRB# CTSB# TXB NC INTB DSRB# TXA DSRA INTA VCC 3 GND NC NC 40 CTSC# VCC A2 A0 A2 A0 # XR16V554/554D 2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO ORDERING INFORMATION PART NUMBER XR16V554IJ XR16V554IV XR16V554DIV XR16V554IL XR16V554IV80 PACKAGE 68-Lead PLCC 64-Lead LQFP 64-Lead LQFP 48-pin QFN 80-Lead LQFP OPERATING TEMPERATURE RANGE -40°C to +85°C -40°C to +85°C -40°C to +85°C -40°C to +85°C -40°C to +85°C DEVICE STATUS Active Active Active Active Active REV. 1.0.2 PIN DESCRIPTIONS Pin Description NAME 48-QFN PIN # 64-LQFP 68-PLCC 80-LQFP TYPE PIN # PIN# PIN # DESCRIPTION DATA BUS INTERFACE A2 A1 A0 D7 D6 D5 D4 D3 D2 D1 D0 IOR# (VCC) 15 16 17 46 45 44 43 42 41 40 39 29 22 23 24 60 59 58 57 56 55 54 53 40 32 33 34 5 4 3 2 1 68 67 66 52 46 47 48 15 14 13 12 11 9 8 7 70 I Address data lines [2:0]. These 3 address lines select one of the internal registers in UART channel A-D during a data bus transaction. Data bus lines [7:0] (bidirectional). I/O I When 16/68# pin is HIGH, the Intel bus interface is selected and this input becomes read strobe (active low). The falling edge instigates an internal read cycle and retrieves the data byte from an internal register pointed by the address lines [A2:A0], puts the data byte on the data bus to allow the host processor to read it on the rising edge. When 16/68# pin is LOW, the Motorola bus interface is selected and this input is not used and should be connected to VCC. When 16/68# pin is HIGH, it selects Intel bus interface and this input becomes write strobe (active low). The falling edge instigates the internal write cycle and the rising edge transfers the data byte on the data bus to an internal register pointed by the address lines. When 16/68# pin is LOW, the Motorola bus interface is selected and this input becomes read (HIGH) and write (LOW) signal. When 16/68# pin is HIGH, this input is chip select A (active low) to enable channel A in the device. When 16/68# pin is LOW, this input becomes the chip select (active low) for the Motorola bus interface. IOW# (R/W#) 7 9 18 31 I CSA# (CS#) 5 7 16 28 I 4 XR16V554/554D REV. 1.0.2 2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO Pin Description NAME CSB# (A3) 48-QFN PIN # 9 64-LQFP 68-PLCC 80-LQFP TYPE PIN # PIN# PIN # 11 20 33 I DESCRIPTION When 16/68# pin is HIGH, this input is chip select B (active low) to enable channel B in the device. When 16/68# pin is LOW, this input becomes address line A3 which is used for channel selection in the Motorola bus interface. When 16/68# pin is HIGH, this input is chip select C (active low) to enable channel C in the device. When 16/68# pin is LOW, this input becomes address line A4 which is used for channel selection in the Motorola bus interface. When 16/68# pin is HIGH, this input is chip select D (active low) to enable channel D in the device. When 16/68# pin is LOW, this input is not used and should be connected VCC. CSC# (A4) 27 38 50 73 I CSD# (VCC) 31 42 54 68 I INTA (IRQ#) 4 6 15 27 O When 16/68# pin is HIGH for Intel bus interface, this (OD) ouput becomes channel A interrupt output. The output state is defined by the user and through the software setting of MCR[3]. INTA is set to the active mode when MCR[3] is set to a logic 1. INTA is set to the three state mode when MCR[3] is set to a logic 0 (default). See MCR[3]. When 16/68# pin is LOW for Motorola bus interface, this output becomes device interrupt output (active low, open drain). An external pull-up resistor is required for proper operation. O When 16/68# pin is HIGH for Intel bus interface, these ouputs become the interrupt outputs for channels B, C, and D. The output state is defined by the user through the software setting of MCR[3]. The interrupt outputs are set to the active mode when MCR[3] is set to a logic 1 and are set to the three state mode when MCR[3] is set to a logic 0 (default). See MCR[3]. When 16/68# pin is LOW for Motorola bus interface, these outputs are unused and will stay at logic zero level. Leave these outputs unconnected. Transmitter Ready (active low). This output is a logically ANDed status of TXRDY# A-D. See Table 5. If this output is unused, leave it unconnected. Receiver Ready (active low). This output is a logically ANDed status of RXRDY# A-D. See Table 5. If this output is unused, leave it unconnected. INTB INTC INTD (N.C.) 10 26 32 12 37 43 21 49 55 34 67 74 TXRDY# - - 39 55 O RXRDY# - - 38 54 O 5 XR16V554/554D 2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO Pin Description NAME INTSEL 48-QFN PIN # 38 64-LQFP 68-PLCC 80-LQFP TYPE PIN # PIN# PIN # 65 6 I DESCRIPTION Interrupt Select (active high, input with internal pulldown). When 16/68# pin is HIGH for Intel bus interface, this pin can be used in conjunction with MCR bit-3 to enable or disable the INT A-D pins or override MCR bit-3 and enable the interrupt outputs. Interrupt outputs are enabled continuously when this pin is HIGH. MCR bit-3 enables and disables the interrupt output pins. In this mode, MCR bit-3 is set to a logic 1 to enable the continuous output. See MCR bit-3 description for full detail. This pin must be LOW in the Motorola bus interface mode. For the 64 pin packages, this pin is bonded to VCC internally in the XR16V554D so the INT outputs operate in the continuous interrupt mode. This pin is bonded to GND internally in the XR16V554 and therefore requires setting MCR bit-3 for enabling the interrupt output pins. REV. 1.0.2 MODEM OR SERIAL I/O INTERFACE TXA TXB TXC TXD RXA RXB RXC RXD RTSA# RTSB# RTSC# RTSD# CTSA# CTSB# CTSC# CTSD# DTRA# DTRB# DTRC# DTRD# DSRA# DSRB# DSRC# DSRD# 6 8 28 30 48 13 22 36 3 11 25 33 1 12 23 35 8 10 39 41 62 20 29 51 5 13 36 44 2 16 33 47 3 15 34 46 1 17 32 48 17 19 51 53 7 29 41 63 14 22 48 56 11 25 45 59 12 24 46 58 10 26 44 60 29 32 69 72 17 44 57 4 26 35 66 75 23 38 63 78 24 37 64 77 22 39 62 79 O UART channels A-D Transmit Data and infrared transmit data. In this mode, the TX signal will be HIGH during reset, or idle (no data). I UART channel A-D Receive Data. Normal receive data input must idle HIGH. O UART channels A-D Request-to-Send (active low) or general purpose output. If these outputs are not used, leave them unconnected. I UART channels A-D Clear-to-Send (active low) or general purpose input. These inputs should be connected to VCC when not used. O UART channels A-D Data-Terminal-Ready (active low) or general purpose output. If these outputs are not used, leave them unconnected. I UART channels A-D Data-Set-Ready (active low) or general purpose input. This input should be connected to VCC when not used. This input has no effect on the UART. 6 XR16V554/554D REV. 1.0.2 2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO Pin Description NAME CDA# CDB# CDC# CDD# RIA# RIB# RIC# RID# 48-QFN PIN # 64-LQFP 68-PLCC 80-LQFP TYPE PIN # PIN# PIN # 64 18 31 49 63 19 30 50 9 27 43 61 8 28 42 62 19 42 59 2 18 43 58 3 I DESCRIPTION UART channels A-D Carrier-Detect (active low) or general purpose input. This input should be connected to VCC when not used. This input has no effect on the UART. UART channels A-D Ring-Indicator (active low) or general purpose input. This input should be connected to VCC when not used. This input has no effect on the UART. I ANCILLARY SIGNALS XTAL1 XTAL2 16/68# 18 19 14 25 26 35 36 31 50 51 I O I Crystal or external clock input. Caution: this input is not 5V tolerant. Crystal or buffered clock output. Intel or Motorola Bus Select (input with internal pull-up). When 16/68# pin is HIGH, 16 or Intel Mode, the device will operate in the Intel bus type of interface. When 16/68# pin is LOW, 68 or Motorola mode, the device will operate in the Motorola bus type of interface. Motorola bus interface is not available on the 64 pin package. When 16/68# pin is HIGH for Intel bus interface, this input becomes the Reset pin (active high). In this case, a 40 ns minimum HIGH pulse on this pin will reset the internal registers and all outputs. The UART transmitter output will be held HIGH, the receiver input will be ignored and outputs are reset during reset period (Table 13). When 16/68# pin is at LOW for Motorola bus interface, this input becomes Reset# pin (active low). This pin functions similarly, but instead of a HIGH pulse, a 40 ns minimum LOW pulse will reset the internal registers and outputs. Motorola bus interface is not available on the 64 pin package. 2.25V to 3.6V power supply. All inputs, except XTAL1, are 5V tolerant. Power supply common, ground. The center pad on the backside of the QFN package is metallic and should be connected to GND on the PCB. The thermal pad size on the PCB should be the approximate size of this center pad and should be solder mask defined. The solder mask opening should be at least 0.0025" inwards from the edge of the PCB thermal pad. RESET (RESET#) 20 27 37 53 I VCC GND GND 2, 24, 37 4, 21, 35, 52 21, 47 Center Pad 14, 28, 45, 61 N/A 13, 30, 47, 64 6, 23, 40, 57 N/A 5, 25, 45, 65 16, 36, 56, 76 N/A Pwr Pwr Pwr 7 XR16V554/554D 2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO Pin Description NAME N.C. 48-QFN PIN # 64-LQFP 68-PLCC 80-LQFP TYPE PIN # PIN# PIN # 1, 10, 20, 21, 30, 40, 41, 49, 52, 60, 61, 71, 80 DESCRIPTION No Connection. These pins are not used in either the Intel or Motorola bus modes. REV. 1.0.2 Pin type: I=Input, O=Output, I/O= Input/output, OD=Output Open Drain. 8 XR16V554/554D REV. 1.0.2 2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO 1.0 PRODUCT DESCRIPTION The XR16V554 (V554) integrates the functions of 4 enhanced 16C550 Universal Asynchrounous Receiver and Transmitter (UART). Each UART is independently controlled and has its own set of device configuration registers. The configuration registers set is 16550 UART compatible for control, status and data transfer. Additionally, each UART channel has 16 bytes of transmit and receive FIFOs, programmable baud rate generator and data rate up to 4 Mbps at 3.3 V. The XR16V554 can operate from 2.25 to 3.6 volts. The V554 is fabricated with an advanced CMOS process. Enhanced FIFO The V554 QUART provides a solution that supports 16 bytes of transmit and receive FIFO memory, instead of one byte in the ST16C454. The V554 is designed to work with high performance data communication systems, that require fast data processing time. Increased performance is realized in the V554 by the larger transmit and receive FIFOs and Receiver FIFO trigger level control. This allows the external processor to handle more networking tasks within a given time. This increases the service interval giving the external CPU additional time for other applications and reducing the overall UART interrupt servicing time. Data Bus Interface, Intel or Motorola Type The V554 provides a single host interface for the 4 UARTs and supports Intel or Motorola microprocessor (CPU) data bus interface. The Intel bus compatible interface allows direct interconnect to Intel compatible type of CPUs using IOR#, IOW# and CSA#, CSB#, CSC# or CSD# inputs for data bus operation. The Motorola bus compatible interface instead uses the R/W#, CS#, A3 and A4 signals for data bus transactions. Few data bus interface signals change their functions depending on user’s selection, see pin description for details. The Intel and Motorola bus interface selection is made through the pin 16/68#. Data Rate The V554 is capable of operation up to 4 Mbps at 3.3V. The device can operate at 3.3V with a crystal oscillator of up to 24 MHz crystal on pins XTAL1 and XTAL2, or external clock source of 64 MHz on XTAL1 pin. With a typical crystal of 14.7456 MHz and through a software option, the user can set the sampling rate for data rates of up to 921.6 Kbps. Enhanced Features The rich feature set of the V554 is available through the internal registers. Selectable receive FIFO trigger levels, programmable baud rates, infrared encoder/decoder interface and modem interface controls are all standard features. In the 16 mode INTSEL and MCR bit-3 can be configured to provide a software controlled or continuous interrupt capability. For backward compatibility to the ST16C554, the 64-pin LQFP does not have the INTSEL pin. Instead, two different LQFP packages are offered. The XR16V554DIV operates in the continuous interrupt enable mode by internally bonding INTSEL to VCC. The XR16V554IV operates in conjunction with MCR bit-3 by internally bonding INTSEL to GND. 9 XR16V554/554D 2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO 2.0 FUNCTIONAL DESCRIPTIONS 2.1 CPU Interface REV. 1.0.2 The CPU interface is 8 data bits wide with 3 address lines and control signals to execute data bus read and write transactions. The V554 data interface supports the Intel compatible types of CPUs and it is compatible to the industry standard 16C550 UART. No clock (oscillator nor external clock) is required for a data bus transaction. Each bus cycle is asynchronous using CS# A-D, IOR# and IOW# or CS#, R/W#, A4 and A3 inputs. All four UART channels share the same data bus for host operations. A typical data bus interconnection for Intel and Motorola mode is shown in Figure 4. FIGURE 4. XR16V554 TYPICAL INTEL/MOTOROLA DATA BUS INTERCONNECTIONS D0 D1 D2 D3 D4 D5 D6 D7 A0 A1 A2 IOR# IOW# UART_CSA# UART_CSB# UART_CSC# UART_CSD# UART_INTA UART_INTB UART_INTC UART_INTD UART_RESET VCC D0 D1 D2 D3 D4 D5 D6 D7 A0 A1 A2 IOR# IOW# CSA# CSB# CSC# CSD# INTA INTB INTC INTD RESET 16/68# GND UART Channel D Similar to Ch A UART Channel B Similar to Ch A VCC TXA RXA DTRA# RTSA# CTSA# DSRA# CDA# RIA# VCC UART Channel A Serial Interface of RS-232 UART Channel C Similar to Ch A Serial Interface of RS-232 Intel Data Bus (16 Mode) Interconnections D0 D1 D2 D3 D4 D5 D6 D7 A0 A1 A2 A3 A4 VCC VCC R/W# UART_CS# VCC VCC D0 D1 D2 D3 D4 D5 D6 D7 A0 A1 A2 CSB# CSC# CSD# IOR# IOW# CSA# UART Channel C Similar to Ch A TXA RXA DTRA# RTSA# CTSA# DSRA# CDA# RIA# UART Channel B Similar to Ch A VCC UART Channel A Serial Interface of RS-232 Serial Interface of RS-232 UART_IRQ# (no connect) (no connect) (no connect) UART_RESET# INTA INTB INTC INTD RESET# 16/68# UART Channel D Similar to Ch A GND Motorola Data Bus (68 Mode) Interconnections 10 XR16V554/554D REV. 1.0.2 2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO 2.2 Device Reset The RESET input resets the internal registers and the serial interface outputs in all channels to their default state (see Table 13). An active high pulse of longer than 40 ns duration will be required to activate the reset function in the device. Following a power-on reset or an external reset, the V554 is software compatible with previous generation of UARTs, 16C454 and 16C554. 2.3 Channel Selection The UART provides the user with the capability to bi-directionally transfer information between an external CPU and an external serial communication device. During Intel Bus Mode (16/68# pin is connected to VCC), a logic 0 on chip select pins, CSA#, CSB#, CSC# or CSD# allows the user to select UART channel A, B, C or D to configure, send transmit data and/or unload receive data to/from the UART. Selecting all four UARTs can be useful during power up initialization to write to the same internal registers, but do not attempt to read from all four uarts simultaneously. Individual channel select functions are shown in Table 1. TABLE 1: CHANNEL A-D SELECT IN 16 MODE CSA# CSB# CSC# CSD# 1 0 1 1 1 0 1 1 0 1 1 0 1 1 1 0 1 0 1 1 1 1 0 0 FUNCTION UART de-selected Channel A selected Channel B selected Channel C selected Channel D selected Channels A-D selected During Motorola Bus Mode (16/68# pin is connected to GND), the package interface pins are configured for connection with Motorola, and other popular microprocessor bus types. In this mode the V554 decodes two additional addresses, A3 and A4, to select one of the four UART ports. The A3 and A4 address decode function is used only when in the Motorola Bus Mode. See Table 2. TABLE 2: CHANNEL A-D SELECT IN 68 MODE CS# 1 0 0 0 0 A4 X 0 0 1 1 A3 X 0 1 0 1 FUNCTION UART de-selected Channel A selected Channel B selected Channel C selected Channel D selected 11 XR16V554/554D 2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO 2.4 Channels A-D Internal Registers REV. 1.0.2 Each UART channel in the V554 has a set of enhanced registers for controlling, monitoring and data loading and unloading. The configuration register set is compatible to those already available in the standard single 16C550. These registers function as data holding registers (THR/RHR), interrupt status and control registers (ISR/IER), a FIFO control register (FCR), receive line status and control registers (LSR/LCR), modem status and control registers (MSR/MCR), programmable data rate (clock) divisor registers (DLL/DLM), and a user accessible scratchpad register (SPR). All the register functions are discussed in full detail later in “Section 3.0, UART INTERNAL REGISTERS” on page 27. 2.5 INT Ouputs for Channels A-D The interrupt outputs change according to the operating mode and enhanced features setup. Table 3 and 4 summarize the operating behavior for the transmitter and receiver. Also see Figure 18 through 23. TABLE 3: INT PIN OPERATION FOR TRANSMITTER FOR CHANNELS A-D FCR BIT-0 = 1 (FIFO ENABLED) FCR BIT-0 = 0 (FIFO DISABLED) INT Pin LOW = a byte in THR HIGH = THR empty FCR Bit-3 = 0 (DMA Mode Disabled) LOW = FIFO above trigger level HIGH = FIFO below trigger level or FIFO empty FCR Bit-3 = 1 (DMA Mode Enabled) LOW = FIFO above trigger level HIGH = FIFO below trigger level or FIFO empty TABLE 4: INT PIN OPERATION FOR RECEIVER FOR CHANNELS A-D FCR BIT-0 = 0 (FIFO DISABLED) FCR BIT-0 = 1 (FIFO ENABLED) FCR Bit-3 = 0 (DMA Mode Disabled) INT Pin LOW = no data HIGH = 1 byte LOW = FIFO below trigger level HIGH = FIFO above trigger level FCR Bit-3 = 1 (DMA Mode Enabled) LOW = FIFO below trigger level HIGH = FIFO above trigger level 2.6 DMA Mode The device does not support direct memory access. The DMA Mode (a legacy term) in this document does not mean “direct memory access” but refers to data block transfer operation. The DMA mode affects the state of the RXRDY# A-D and TXRDY# A-D output pins. The transmit and receive FIFO trigger levels provide additional flexibility to the user for block mode operation. The LSR bits 5-6 provide an indication when the transmitter is empty or has an empty location(s) for more data. The user can optionally operate the transmit and receive FIFO in the DMA mode (FCR bit-3 = 1). When the transmit and receive FIFOs are enabled and the DMA mode is disabled (FCR bit-3 = 0), the V554 is placed in single-character mode for data transmit or receive operation. When DMA mode is enabled (FCR bit-3 = 1), the user takes advantage of block mode operation by loading or unloading the FIFO in a block sequence determined by the programmed trigger level. The following table show their behavior. Also see Figure 18 through 23. 12 XR16V554/554D REV. 1.0.2 2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO TABLE 5: TXRDY# AND RXRDY# OUTPUTS IN FIFO AND DMA MODE FOR CHANNELS A-D PINS FCR BIT-0=0 (FIFO DISABLED) FCR BIT-0=1 (FIFO ENABLED) FCR BIT-3 = 0 (DMA MODE DISABLED) RXRDY# LOW = 1 byte HIGH = no data LOW = THR empty HIGH = byte in THR LOW = at least 1 byte in FIFO HIGH = FIFO empty LOW = FIFO empty HIGH = at least 1 byte in FIFO FCR BIT-3 = 1 (DMA MODE ENABLED) HIGH to LOW transition when FIFO reaches the trigger level, or timeout occurs LOW to HIGH transition when FIFO empties LOW = FIFO has at least 1 empty location HIGH = FIFO is full TXRDY# 2.7 Crystal Oscillator or External Clock Input The V554 includes an on-chip oscillator (XTAL1 and XTAL2) to produce a clock for both UART sections in the device. The CPU data bus does not require this clock for bus operation. The crystal oscillator provides a system clock to the Baud Rate Generators (BRG) section found in each of the UART. XTAL1 is the input to the oscillator or external clock buffer input with XTAL2 pin being the output. Caution: the XTAL1 input is not 5V tolerant. For programming details, see “Section 2.8, Programmable Baud Rate Generator” on page 21. FIGURE 5. TYPICAL CRYSTAL CONNECTIONS R=300K to 400K XTAL1 14.7456 MHz XTAL2 C1 22-47pF C2 22-47pF The on-chip oscillator is designed to use an industry standard microprocessor crystal (parallel resonant, fundamental frequency with 10-22 pF capacitance load, ESR of 20-120 ohms and 100ppm frequency tolerance) connected externally between the XTAL1 and XTAL2 pins. Typical oscillator connections are shown in Figure 5. Alternatively, an external clock can be connected to the XTAL1 pin to clock the internal baud rate generator for standard or custom rates. For further reading on oscillator circuit please see application note DAN108 on EXAR’s web site. 2.8 Programmable Baud Rate Generator Each UART has its own Baud Rate Generator (BRG) for the transmitter and receiver. The BRG further divides this clock by a programmable divisor between 1 and (216 - 0.0625) in increments of 0.0625 (1/16) to obtain a 16X sampling rate clock of the serial data rate. The sampling rate clock is used by the transmitter for data bit shifting and receiver for data sampling. The BRG divisor defaults to the maximum baud rate (DLL = 0x01 and DLM = 0x00) upon power up and reset. Programming the Baud Rate Generator Registers DLL and DLM provides the capability for selecting the operating data rate. Table 6 shows the standard data rates available with a 24MHz crystal or external clock at 16X clock rate. If the pre-scaler is used (MCR bit-7 = 1), the output data rate will be 4 times less than that shown in Table 6. 13 XR16V554/554D 2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO REV. 1.0.2 FIGURE 6. BAUD RATE GENERATOR To Other Channels DLL and DLM Registers XTAL1 XTAL2 Crystal Osc / Buffer Programmable Baud Rate Generator Logic 16 X Sampling Rate Clock to Transmitter and Receiver TABLE 6: TYPICAL DATA RATES WITH A 14.7456 MHZ CRYSTAL OR EXTERNAL CLOCK OUTPUT Data Rate MCR Bit-7=0 400 2400 4800 9600 19.2k 38.4k 76.8k 153.6k 230.4k 460.8k 921.6k DIVISOR FOR 16x Clock (Decimal) 2304 384 192 96 48 24 12 6 4 2 1 DIVISOR FOR 16x Clock (HEX) 900 180 C0 60 30 18 0C 06 04 02 01 DLM PROGRAM VALUE (HEX) 09 01 00 00 00 00 00 00 00 00 00 DLL PROGRAM VALUE (HEX) 00 80 C0 60 30 18 0C 06 04 02 01 DATA RATE ERROR (%) 0 0 0 0 0 0 0 0 0 0 0 2.9 Transmitter The transmitter section comprises of an 8-bit Transmit Shift Register (TSR) and 16 bytes of FIFO which includes a byte-wide Transmit Holding Register (THR). TSR shifts out every data bit with the 16X internal sampling clock. A bit time is 16X clock periods. The transmitter sends the start-bit followed by the number of data bits, inserts the proper parity-bit if enabled, and adds the stop-bit(s). The status of the FIFO and TSR are reported in the Line Status Register (LSR bit-5 and bit-6). 14 XR16V554/554D REV. 1.0.2 2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO Transmit Holding Register (THR) - Write Only 2.9.1 The transmit holding register is an 8-bit register providing a data interface to the host processor. The host writes transmit data byte to the THR to be converted into a serial data stream including start-bit, data bits, parity-bit and stop-bit(s). The least-significant-bit (Bit-0) becomes first data bit to go out. The THR is the input register to the transmit FIFO of 16 bytes when FIFO operation is enabled by FCR bit-0. Every time a write operation is made to the THR, the FIFO data pointer is automatically bumped to the next sequential data location. 2.9.2 Transmitter Operation in non-FIFO Mode The host loads transmit data to THR one character at a time. The THR empty flag (LSR bit-5) is set when the data byte is transferred to TSR. THR flag can generate a transmit empty interrupt (ISR bit-1) when it is enabled by IER bit-1. The TSR flag (LSR bit-6) is set when TSR becomes completely empty. FIGURE 7. TRANSMITTER OPERATION IN NON-FIFO MODE Data Byte Transmit Holding Register (THR) THR Interrupt (ISR bit-1) Enabled by IER bit-1 16X Clock Transmit Shift Register (TSR) M S B L S B TXNOFIFO1 2.9.3 Transmitter Operation in FIFO Mode The host may fill the transmit FIFO with up to 16 bytes of transmit data. The THR empty flag (LSR bit-5) is set whenever the FIFO is empty. The THR empty flag can generate a transmit empty interrupt (ISR bit-1) when the FIFO becomes empty. The transmit empty interrupt is enabled by IER bit-1. The TSR flag (LSR bit-6) is set when TSR/FIFO becomes empty. FIGURE 8. TRANSMITTER OPERATION IN FIFO AND FLOW CONTROL MODE Transmit Data Byte Transmit FIFO THR Interrupt (ISR bit-1) When it becomes empty. FIFO is Enabled by FCR Bit-0=1 16X Clock Transmit Data Shift Register ( TSR ) TXFIFO1 15 XR16V554/554D 2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO 2.10 Receiver REV. 1.0.2 The receiver section contains an 8-bit Receive Shift Register (RSR) and 16 bytes of FIFO which includes a byte-wide Receive Holding Register (RHR). The RSR uses the 16X clock for timing. It verifies and validates every bit on the incoming character in the middle of each data bit. On the falling edge of a start or false start bit, an internal receiver counter starts counting at the 16X clock rate. After 8 clocks the start bit period should be at the center of the start bit. At this time the start bit is sampled and if it is still LOW it is validated. Evaluating the start bit in this manner prevents the receiver from assembling a false character. The rest of the data bits and stop bits are sampled and validated in this same manner to prevent false framing. If there were any error(s), they are reported in the LSR register bits 2-4. Upon unloading the receive data byte from RHR, the receive FIFO pointer is bumped and the error tags are immediately updated to reflect the status of the data byte in RHR register. RHR can generate a receive data ready interrupt upon receiving a character or delay until it reaches the FIFO trigger level. Furthermore, data delivery to the host is guaranteed by a receive data ready time-out interrupt when data is not received for 4 word lengths as defined by LCR[1:0] plus 12 bits time. This is equivalent to 3.7-4.6 character times. The RHR interrupt is enabled by IER bit-0. See Figure 9 and Figure 10 below. 2.10.1 Receive Holding Register (RHR) - Read-Only The Receive Holding Register is an 8-bit register that holds a receive data byte from the Receive Shift Register. It provides the receive data interface to the host processor. The RHR register is part of the receive FIFO of 16 bytes by 11-bit wide, the 3 extra bits are for the 3 error tags to be reported in LSR register. When the FIFO is enabled by FCR bit-0, the RHR contains the first data character received by the FIFO. After the RHR is read, the next character byte is loaded into the RHR and the errors associated with the current data byte are immediately updated in the LSR bits 2-4. FIGURE 9. RECEIVER OPERATION IN NON-FIFO MODE 16X Clock Receive Data Shift Register (RSR) Data Bit Validation Receive Data Characters Receive Data Byte and Errors Error Tags in LSR bits 4:2 Receive Data Holding Register (RHR) RHR Interrupt (ISR bit-2) RXFIFO1 16 XR16V554/554D REV. 1.0.2 2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO FIGURE 10. RECEIVER OPERATION IN FIFO 16X C lock R eceive D ata Shift R egister (R SR ) D ata Bit V alidation R eceive D ata C haracters 16 bytes by 11-bit w ide FIFO E xam ple : - R X FIFO trigger level selected at 8 bytes (See N ote Below ) D ata falls to 4 Error Tags (16-sets) Asking for sending data w hen data falls below the flow control trigger level to restart rem ote transm itter. R H R Interrupt (IS R bit-2) program m ed for desired FIFO trigger level. FIFO is Enabled by F C R bit-0=1 Asking for stopping data w hen data fills above the flow control trigger level to suspend rem ote transm itter. R eceive D ata FIFO FIFO Trigger=8 D ata fills to 14 Error Tags in LSR bits 4:2 R eceive D ata Byte and Errors R eceive D ata R X FIFO 1 17 XR16V554/554D 2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO 2.11 Internal Loopback REV. 1.0.2 The V554 UART provides an internal loopback capability for system diagnostic purposes. The internal loopback mode is enabled by setting MCR register bit-4 to logic 1. All regular UART functions operate normally. Figure 11 shows how the modem port signals are re-configured. Transmit data from the transmit shift register output is internally routed to the receive shift register input allowing the system to receive the same data that it was sending. The TX pin is held HIGH or mark condition while RTS# and DTR# are de-asserted, and CTS#, DSR# CD# and RI# inputs are ignored. Caution: the RX input must be held HIGH during loopback test else upon exiting the loopback test the UART may detect and report a false “break” signal. FIGURE 11. INTERNAL LOOPBACK VCC Transmit Shift Register (THR/FIFO) MCR bit-4=1 Internal Data Bus Lines and Control Signals Receive Shift Register (RHR/FIFO) VCC RTS# A-D Modem / General Purpose Control Logic RTS# TX A-D RX A-D CTS# VCC DTR# CTS# A-D DTR# A-D DSR# OP1# RI# OP2# CD# DSR# A-D RI# A-D CD# A-D 18 XR16V554/554D REV. 1.0.2 2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO 3.0 UART INTERNAL REGISTERS Each UART channel in the V554 has its own set of configuration registers selected by address lines A0, A1 and A2 with a specific channel selected (See Table 1 and Table 2). The complete register set is shown on Table 7 and Table 8. TABLE 7: UART INTERNAL REGISTERS A2,A1,A0 ADDRESSES REGISTER READ/WRITE COMMENTS 16C550 COMPATIBLE REGISTERS 000 RHR - Receive Holding Register THR - Transmit Holding Register DLL - Divisor LSB DLM - Divisor MSB IER - Interrupt Enable Register ISR - Interrupt Status Register FCR - FIFO Control Register LCR - Line Control Register MCR - Modem Control Register LSR - Line Status Register MSR - Modem Status Register SPR - Scratch Pad Register Read-only Write-only Read/Write Read/Write Read/Write Read-only Write-only Read/Write Read/Write Read-only LCR[7] = 0 110 111 Read-only Read/Write LCR[7] = 0 LCR[7] = 0 000 001 001 010 LCR[7] = 1, LCR ≠ 0xBF 011 100 101 19 XR16V554/554D 2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO REV. 1.0.2 TABLE 8: INTERNAL REGISTERS DESCRIPTION ADDRESS A2-A0 REG NAME READ/ WRITE BIT-7 BIT-6 BIT-5 BIT-4 BIT-3 BIT-2 BIT-1 BIT-0 COMMENT 16C550 Compatible Registers 000 000 001 RHR THR IER RD WR RD/WR Bit-7 Bit-7 0 Bit-6 Bit-6 0 Bit-5 Bit-5 0 Bit-4 Bit-4 0 Bit-3 Bit-3 Bit-2 Bit-2 Bit-1 Bit-1 Bit-0 Bit-0 Modem RX Line TX RX Stat. Int. Stat. Empty Data Enable Int. Int Int. Enable Enable Enable INT Source Bit-3 DMA Mode Enable Parity Enable INT INT INT Source Source Source Bit-2 Bit-1 Bit-0 TX FIFO Reset Stop Bits RX FIFO Reset FIFOs Enable LCR[7] = 0 010 ISR RD FIFOs FIFOs Enabled Enabled RX FIFO RX FIFO Trigger Trigger Divisor Enable Set TX Break 0 0 010 FCR WR 0 0 011 LCR RD/WR Set Parity 0 Even Parity Word Word Length Length Bit-1 Bit-0 100 MCR RD/WR 0 0 Internal Lopback Enable INT Output Enable (OP2#) RX Framing Error Delta CD# Bit-3 Rsvd RTS# DTR# (OP1#) Output Output Control Control 101 LSR RD/WR RX FIFO Global Error CD# Input Bit-7 THR & TSR Empty THR Empty RX Break RX Parity Error RX Overrun Error Delta DSR# Bit-1 RX Data Ready LCR[7] = 0 110 111 MSR SPR RD/WR RD/WR RI# Input Bit-6 DSR# Input Bit-5 CTS# Input Bit-4 Delta RI# Bit-2 Delta CTS# Bit-0 Baud Rate Generator Divisor 000 001 DLL DLM RD/WR RD/WR Bit-7 Bit-7 Bit-6 Bit-6 Bit-5 Bit-5 Bit-4 Bit-4 Bit-3 Bit-3 Bit-2 Bit-2 Bit-1 Bit-1 Bit-0 Bit-0 LCR[7]=1 LCR≠0xBF 4.0 INTERNAL REGISTER DESCRIPTIONS 4.1 Receive Holding Register (RHR) - Read- Only SEE”RECEIVER” ON PAGE 24. 4.2 Transmit Holding Register (THR) - Write-Only SEE”TRANSMITTER” ON PAGE 22. 4.3 Interrupt Enable Register (IER) - Read/Write The Interrupt Enable Register (IER) masks the interrupts from receive data ready, transmit empty, line status and modem status registers. These interrupts are reported in the Interrupt Status Register (ISR). 20 XR16V554/554D REV. 1.0.2 2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO IER versus Receive FIFO Interrupt Mode Operation 4.3.1 When the receive FIFO (FCR BIT-0 = 1) and receive interrupts (IER BIT-0 = 1) are enabled, the RHR interrupts (see ISR bits 2 and 3) status will reflect the following: A. The receive data available interrupts are issued to the host when the FIFO has reached the programmed trigger level. It will be cleared when the FIFO drops below the programmed trigger level. B. FIFO level will be reflected in the ISR register when the FIFO trigger level is reached. Both the ISR register status bit and the interrupt will be cleared when the FIFO drops below the trigger level. C. The receive data ready bit (LSR BIT-0) is set as soon as a character is transferred from the shift register to the receive FIFO. It is reset when the FIFO is empty. 4.3.2 IER versus Receive/Transmit FIFO Polled Mode Operation When FCR BIT-0 equals a logic 1 for FIFO enable; resetting IER bits 0-3 enables the XR16V554 in the FIFO polled mode of operation. Since the receiver and transmitter have separate bits in the LSR either or both can be used in the polled mode by selecting respective transmit or receive control bit(s). A. LSR BIT-0 indicates there is data in RHR or RX FIFO. B. LSR BIT-1 indicates an overrun error has occurred and that data in the FIFO may not be valid. C. LSR BIT 2-4 provides the type of receive data errors encountered for the data byte in RHR, if any. D. LSR BIT-5 indicates THR is empty. E. LSR BIT-6 indicates when both the transmit FIFO and TSR are empty. F. LSR BIT-7 indicates a data error in at least one character in the RX FIFO. IER[0]: RHR Interrupt Enable The receive data ready interrupt will be issued when RHR has a data character in the non-FIFO mode or when the receive FIFO has reached the programmed trigger level in the FIFO mode. • Logic 0 = Disable the receive data ready interrupt (default). • Logic 1 = Enable the receiver data ready interrupt. IER[1]: THR Interrupt Enable This bit enables the Transmit Ready interrupt which is issued whenever the THR becomes empty. If the THR is empty when this bit is enabled, an interrupt will be generated. • Logic 0 = Disable Transmit Ready interrupt (default). • Logic 1 = Enable Transmit Ready interrupt. IER[2]: Receive Line Status Interrupt Enable If any of the LSR register bits 1, 2, 3 or 4 is a logic 1, it will generate an interrupt to inform the host controller about the error status of the current data byte in FIFO. LSR bit-1 generates an interrupt immediately when an overrun occurs. LSR bits 2-4 generate an interrupt when the character in the RHR has an error. • Logic 0 = Disable the receiver line status interrupt (default). • Logic 1 = Enable the receiver line status interrupt. IER[3]: Modem Status Interrupt Enable • Logic 0 = Disable the modem status register interrupt (default). • Logic 1 = Enable the modem status register interrupt. IER[7:4]: Reserved 21 XR16V554/554D 2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO 4.4 Interrupt Status Register (ISR) REV. 1.0.2 The UART provides multiple levels of prioritized interrupts to minimize external software interaction. The Interrupt Status Register (ISR) provides the user with six interrupt status bits. Performing a read cycle on the ISR will give the user the current highest pending interrupt level to be serviced, others are queued up to be serviced next. No other interrupts are acknowledged until the pending interrupt is serviced. The Interrupt Source Table, Table 9, shows the data values (bit 0-3) for the interrupt priority levels and the interrupt sources associated with each of these interrupt levels. 4.4.1 Interrupt Generation: • LSR is by any of the LSR bits 1, 2, 3 and 4. • RXRDY Data Ready is by RX trigger level. • RXRDY Data Time-out is by a 4-char plus 12 bits delay timer. • TXRDY is by TX FIFO empty. • MSR is by any of the MSR bits 0, 1, 2 and 3. 4.4.2 Interrupt Clearing: • LSR interrupt is cleared by a read to the LSR register. • RXRDY interrupt is cleared by reading data until FIFO falls below the trigger level. • RXRDY Time-out interrupt is cleared by reading RHR. • TXRDY interrupt is cleared by a read to the ISR register or writing to THR. • MSR interrupt is cleared by a read to the MSR register. ] TABLE 9: INTERRUPT SOURCE AND PRIORITY LEVEL PRIORITY LEVEL 1 2 3 4 5 BIT-3 0 1 0 0 0 0 ISR REGISTER STATUS BITS BIT-2 1 1 1 0 0 0 BIT-1 1 0 0 1 0 0 BIT-0 0 0 0 0 0 1 LSR (Receiver Line Status Register) RXRDY (Receive Data Time-out) RXRDY (Received Data Ready) TXRDY (Transmit Ready) MSR (Modem Status Register) None (default) SOURCE OF INTERRUPT ISR[0]: Interrupt Status • Logic 0 = An interrupt is pending and the ISR contents may be used as a pointer to the appropriate interrupt service routine. • Logic 1 = No interrupt pending (default condition). ISR[3:1]: Interrupt Status These bits indicate the source for a pending interrupt at interrupt priority levels (See Interrupt Source Table 9). ISR[4]: Reserved ISR[5]: Reserved 22 XR16V554/554D REV. 1.0.2 2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO ISR[7:6]: FIFO Enable Status These bits are set to a logic 0 when the FIFOs are disabled. They are set to a logic 1 when the FIFOs are enabled. 4.5 FIFO Control Register (FCR) - Write-Only This register is used to enable the FIFOs, clear the FIFOs, set the receive FIFO trigger levels, and select the DMA mode. The DMA, and FIFO modes are defined as follows: FCR[0]: TX and RX FIFO Enable • Logic 0 = Disable the transmit and receive FIFO (default). • Logic 1 = Enable the transmit and receive FIFOs. This bit must be set to logic 1 when other FCR bits are written or they will not be programmed. FCR[1]: RX FIFO Reset This bit is only active when FCR bit-0 is a ‘1’. • Logic 0 = No receive FIFO reset (default). • Logic 1 = Reset the receive FIFO pointers and FIFO level counter logic (the receive shift register is not cleared or altered). This bit will return to a logic 0 after resetting the FIFO. FCR[2]: TX FIFO Reset This bit is only active when FCR bit-0 is a ‘1’. • Logic 0 = No transmit FIFO reset (default). • Logic 1 = Reset the transmit FIFO pointers and FIFO level counter logic (the transmit shift register is not cleared or altered). This bit will return to a logic 0 after resetting the FIFO. FCR[3]: DMA Mode Select Controls the behavior of the TXRDY and RXRDY pins. See DMA operation section for details. • Logic 0 = Normal Operation (default). • Logic 1 = DMA Mode. FCR[5:4]: Reserved FCR[7:6]: Receive FIFO Trigger Select (logic 0 = default, RX trigger level =1) These 2 bits are used to set the trigger level for the receive FIFO. The UART will issue a receive interrupt when the number of the characters in the FIFO crosses the trigger level. Table 10 shows the complete selections. TABLE 10: RECEIVE FIFO TRIGGER LEVEL SELECTION FCR BIT-7 0 0 1 1 FCR BIT-6 0 1 0 1 RECEIVE TRIGGER LEVEL 1 4 8 14 23 XR16V554/554D 2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO 4.6 Line Control Register (LCR) - Read/Write REV. 1.0.2 The Line Control Register is used to specify the asynchronous data communication format. The word or character length, the number of stop bits, and the parity are selected by writing the appropriate bits in this register. LCR[1:0]: TX and RX Word Length Select These two bits specify the word length to be transmitted or received. BIT-1 0 0 1 1 BIT-0 0 1 0 1 WORD LENGTH 5 (default) 6 7 8 LCR[2]: TX and RX Stop-bit Length Select The length of stop bit is specified by this bit in conjunction with the programmed word length. BIT-2 0 1 1 WORD LENGTH STOP BIT LENGTH (BIT TIME(S)) 1 (default) 1-1/2 2 5,6,7,8 5 6,7,8 LCR[3]: TX and RX Parity Select Parity or no parity can be selected via this bit. The parity bit is a simple way used in communications for data integrity check. See Table 11 for parity selection summary below. • Logic 0 = No parity. • Logic 1 = A parity bit is generated during the transmission while the receiver checks for parity error of the data character received. LCR[4]: TX and RX Parity Select If the parity bit is enabled with LCR bit-3 set to a logic 1, LCR BIT-4 selects the even or odd parity format. • Logic 0 = ODD Parity is generated by forcing an odd number of logic 1’s in the transmitted character. The receiver must be programmed to check the same format (default). • Logic 1 = EVEN Parity is generated by forcing an even number of logic 1’s in the transmitted character. The receiver must be programmed to check the same format. 24 XR16V554/554D REV. 1.0.2 2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO LCR[5]: TX and RX Parity Select If the parity bit is enabled, LCR BIT-5 selects the forced parity format. • LCR BIT-5 = logic 0, parity is not forced (default). • LCR BIT-5 = logic 1 and LCR BIT-4 = logic 0, parity bit is forced to HIGH for the transmit and receive data. • LCR BIT-5 = logic 1 and LCR BIT-4 = logic 1, parity bit is forced to LOW for the transmit and receive data. TABLE 11: PARITY SELECTION LCR BIT-5 LCR BIT-4 LCR BIT-3 X 0 0 1 1 X 0 1 0 1 0 1 1 1 1 PARITY SELECTION No parity Odd parity Even parity Force parity to mark, HIGH Forced parity to space, LOW LCR[6]: Transmit Break Enable When enabled, the Break control bit causes a break condition to be transmitted (the TX output is forced to a “space’, logic 0, state). This condition remains, until disabled by setting LCR bit-6 to a logic 0. • Logic 0 = No TX break condition. (default) • Logic 1 = Forces the transmitter output (TX) to a “space”, logic 0, for alerting the remote receiver of a line break condition. LCR[7]: Baud Rate Divisors Enable Baud rate generator divisor (DLL/DLM) enable. • Logic 0 = Data registers are selected (default). • Logic 1 = Divisor latch registers are selected. 4.7 Modem Control Register (MCR) or General Purpose Outputs Control - Read/Write The MCR register is used for controlling the serial/modem interface signals or general purpose inputs/outputs. MCR[0]: DTR# Output The DTR# pin is a modem control output. If the modem interface is not used, this output may be used as a general purpose output. • Logic 0 = Force DTR# output HIGH (default). • Logic 1 = Force DTR# output LOW. MCR[1]: RTS# Output The RTS# pin is a modem control output. If the modem interface is not used, this output may be used as a general purpose output. • Logic 0 = Force RTS# output HIGH (default). • Logic 1 = Force RTS# output LOW. MCR[2]: Reserved OP1# is not available as an output pin on the V554. But it is available for use during Internal Loopback Mode. In the Loopback Mode, this bit is used to write the state of the modem RI# interface signal. 25 XR16V554/554D 2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO MCR[3]: INT Output Enable Enable or disable INT outputs to become active or in three-state. This function is associated with the INTSEL input, see below table for details. This bit is also used to control the OP2# signal during internal loopback mode. INTSEL pin must be LOW during 68 mode. REV. 1.0.2 • Logic 0 = INT (A-D) outputs disabled (three state) in the 16 mode (default). During internal loopback mode, OP2# is HIGH. • Logic 1 = INT (A-D) outputs enabled (active) in the 16 mode. During internal loopback mode, OP2# is LOW. TABLE 12: INT OUTPUT MODES INTSEL PIN 0 0 1 MCR BIT-3 0 1 X INT A-D OUTPUTS IN 16 MODE Three-State Active Active MCR[4]: Internal Loopback Enable • Logic 0 = Disable loopback mode (default). • Logic 1 = Enable local loopback mode, see loopback section and Figure 11. MCR[7:5]: Reserved 4.8 Line Status Register (LSR) - Read/Write This register is writeable but it is not recommended. The LSR provides the status of data transfers between the UART and the host. If IER bit-2 is enabled, LSR bit-1 will generate an interrupt immediately and LSR bits 2-4 will generate an interrupt when a character with an error is in the RHR. LSR[0]: Receive Data Ready Indicator • Logic 0 = No data in receive holding register or FIFO (default). • Logic 1 = Data has been received and is saved in the receive holding register or FIFO. LSR[1]: Receiver Overrun Flag • Logic 0 = No overrun error (default). • Logic 1 = Overrun error. A data overrun error condition occurred in the receive shift register. This happens when additional data arrives while the FIFO is full. In this case the previous data in the receive shift register is overwritten. Note that under this condition the data byte in the receive shift register is not transferred into the FIFO, therefore the data in the FIFO is not corrupted by the error. LSR[2]: Receive Data Parity Error Tag • Logic 0 = No parity error (default). • Logic 1 = Parity error. The receive character in RHR does not have correct parity information and is suspect. This error is associated with the character available for reading in RHR. LSR[3]: Receive Data Framing Error Tag • Logic 0 = No framing error (default). • Logic 1 = Framing error. The receive character did not have a valid stop bit(s). This error is associated with the character available for reading in RHR. 26 XR16V554/554D REV. 1.0.2 2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO LSR[4]: Receive Break Tag • Logic 0 = No break condition (default). • Logic 1 = The receiver received a break signal (RX was LOW for at least one character frame time). In the FIFO mode, only one break character is loaded into the FIFO. The break indication remains until the RX input returns to the idle condition, “mark” or HIGH. LSR[5]: Transmit Holding Register Empty Flag This bit is the Transmit Holding Register Empty indicator. The THR bit is set to a logic 1 when the last data byte is transferred from the transmit holding register to the transmit shift register. The bit is reset to logic 0 concurrently with the data loading to the transmit holding register by the host. In the FIFO mode this bit is set when the transmit FIFO is empty, it is cleared when the transmit FIFO contains at least 1 byte. LSR[6]: THR and TSR Empty Flag This bit is set to a logic 1 whenever the transmitter goes idle. It is set to logic 0 whenever either the THR or TSR contains a data character. In the FIFO mode this bit is set to a logic 1 whenever the transmit FIFO and transmit shift register are both empty. LSR[7]: Receive FIFO Data Error Flag • Logic 0 = No FIFO error (default). • Logic 1 = A global indicator for the sum of all error bits in the RX FIFO. At least one parity error, framing error or break indication is in the FIFO data. This bit clears when there is no more error(s) in any of the bytes in the RX FIFO. 4.9 Modem Status Register (MSR) - Read/Write This register is writeable but it is not recommended. The MSR provides the current state of the modem interface input signals. Lower four bits of this register are used to indicate the changed information. These bits are set to a logic 1 whenever a signal from the modem changes state. These bits may be used for general purpose inputs when they are not used with modem signals. MSR[0]: Delta CTS# Input Flag • Logic 0 = No change on CTS# input (default). • Logic 1 = The CTS# input has changed state since the last time it was monitored. A modem status interrupt will be generated if MSR interrupt is enabled (IER bit-3). MSR[1]: Delta DSR# Input Flag • Logic 0 = No change on DSR# input (default). • Logic 1 = The DSR# input has changed state since the last time it was monitored. A modem status interrupt will be generated if MSR interrupt is enabled (IER bit-3). MSR[2]: Delta RI# Input Flag • Logic 0 = No change on RI# input (default). • Logic 1 = The RI# input has changed from LOW to HIGH, ending of the ringing signal. A modem status interrupt will be generated if MSR interrupt is enabled (IER bit-3). MSR[3]: Delta CD# Input Flag • Logic 0 = No change on CD# input (default). • Logic 1 = Indicates that the CD# input has changed state since the last time it was monitored. A modem status interrupt will be generated if MSR interrupt is enabled (IER bit-3). 27 XR16V554/554D 2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO MSR[4]: CTS Input Status A HIGH on the CTS# pin will stop UART transmitter as soon as the current character has finished transmission, and a LOW will resume data transmission. Normally MSR bit-4 bit is the compliment of the CTS# input. However in the loopback mode, this bit is equivalent to the RTS# bit in the MCR register. The CTS# input may be used as a general purpose input when the modem interface is not used. MSR[5]: DSR Input Status Normally this bit is the complement of the DSR# input. In the loopback mode, this bit is equivalent to the DTR# bit in the MCR register. The DSR# input may be used as a general purpose input when the modem interface is not used. MSR[6]: RI Input Status Normally this bit is the complement of the RI# input. In the loopback mode this bit is equivalent to bit-2 in the MCR register. The RI# input may be used as a general purpose input when the modem interface is not used. MSR[7]: CD Input Status Normally this bit is the complement of the CD# input. In the loopback mode this bit is equivalent to bit-3 in the MCR register. The CD# input may be used as a general purpose input when the modem interface is not used. 4.10 Scratch Pad Register (SPR) - Read/Write REV. 1.0.2 This is a 8-bit general purpose register for the user to store temporary data. 4.11 Baud Rate Generator Registers (DLL and DLM) - Read/Write These registers make-up the value of the baud rate divisor. The concatenation of the contents of DLM and DLL gives the 16-bit divisor value. See ”Section 2.8, Programmable Baud Rate Generator” on page 21. 28 XR16V554/554D REV. 1.0.2 2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO TABLE 13: UART RESET CONDITIONS FOR CHANNELS A-D REGISTERS DLM, DLL RESET STATE DLM = 0x00 and DLL = 0x01. Only resets to these values during a power up. They do not reset when the Reset Pin is asserted. Bits 7-0 = 0xXX Bits 7-0 = 0xXX Bits 7-0 = 0x00 Bits 7-0 = 0x00 Bits 7-0 = 0x01 Bits 7-0 = 0x00 Bits 7-0 = 0x00 Bits 7-0 = 0x60 Bits 3-0 = Logic 0 Bits 7-4 = Logic levels of the inputs inverted Bits 7-0 = 0xFF RESET STATE HIGH HIGH HIGH HIGH LOW XR16V554 = Three-State Condition (INTSEL = LOW) XR16V554 = LOW (INTSEL = HIGH) XR16V554D = LOW HIGH (INTSEL = LOW) RHR THR IER FCR ISR LCR MCR LSR MSR SPR I/O SIGNALS TX RTS# DTR# RXRDY# TXRDY# INT (16 Mode) IRQ# (68 Mode) 29 XR16V554/554D 2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO REV. 1.0.2 ABSOLUTE MAXIMUM RATINGS Power Supply Range Voltage at Any Pin Operating Temperature Storage Temperature Package Dissipation 4 Volts GND-0.3 V to 5.5 V -40o to +85oC -65o to +150oC 500 mW TYPICAL PACKAGE THERMAL RESISTANCE DATA (MARGIN OF ERROR: ± 15%) Thermal Resistance (48-QFN) Thermal Resistance (64-LQFP) Thermal Resistance (68-PLCC) Thermal Resistance (80-LQFP) theta-ja = 28oC/W, theta-jc = 10.5oC/W theta-ja = 50oC/W, theta-jc = 11oC/W theta-ja = 46oC/W, theta-jc = 17oC/W theta-ja = 37oC/W, theta-jc = 7oC/W ELECTRICAL CHARACTERISTICS DC ELECTRICAL CHARACTERISTICS UNLESS OTHERWISE NOTED: TA = -40O TO +85OC, VCC IS 2.25 TO 3.6V SYMBOL VILCK VIHCK VIL VIH VOL PARAMETER Clock Input Low Level Clock Input High Level Input Low Voltage Input High Voltage Output Low Voltage 0.4 VOH Output High Voltage 1.8 IIL IIH CIN ICC Input Low Leakage Current Input High Leakage Current Input Pin Capacitance Power Supply Current ±15 ±15 5 1.7 ±15 ±15 5 3 2.0 LIMITS 2.5V MIN MAX -0.3 2.0 -0.3 1.8 0.4 VCC 0.5 5.5 LIMITS 3.3V MIN MAX -0.3 2.4 -0.3 2.0 0.6 VCC 0.7 5.5 0.4 UNITS V V V V V V V V uA uA pF mA Ext Clk = 2MHz IOL = 6 mA IOL = 4 mA IOH = -4 mA IOH = -2 mA CONDITIONS 30 XR16V554/554D REV. 1.0.2 2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO AC ELECTRICAL CHARACTERISTICS TA = -40O TO +85OC, VCC IS 2.25 TO 3.6V, 70 PF LOAD WHERE APPLICABLE SYMBOL PARAMETER LIMITS 2.5V ± 10% MIN MAX 24 50 10 0 0 50 50 50 45 10 50 50 10 5 0 0 0 45 10 10 5 10 50 50 50 50 50 10 5 5 40 40 50 50 50 40 40 10 5 0 0 0 35 10 7 0 0 40 40 40 35 10 LIMITS 3.3V ± 10% MIN MAX 24 64 UNIT XTAL1 ECLK TECLK TAS TAH TCS TRD TDY TRDV TDD TWR TDY TDS TDH TADS TADH TRWS TRDA TRDH TWDS TWDH TRWH TCSL TCSD TWDO TMOD TRSI UART Crystal Frequency External Clock Frequency External Clock Time Period Address Setup Time (16 Mode) Address Hold Time (16 Mode) Chip Select Width (16 Mode) IOR# Strobe Width (16 Mode) Read Cycle Delay (16 Mode) Data Access Time (16 Mode) Data Disable Time (16 Mode) IOW# Strobe Width (16 Mode) Write Cycle Delay (16 Mode) Data Setup Time (16 Mode) Data Hold Time (16 Mode) Address Setup (68 Mode) Address Hold (68 Mode) R/W# Setup to CS# (68 Mode) Data Access Time (68 mode) Data Disable Time (68 mode) Write Data Setup (68 mode) Write Data Hold (68 Mode) CS# De-asserted to R/W# De-asserted (68 Mode) CS# Strobe Width (68 Mode) CS# Cycle Delay (68 Mode) Delay From IOW# To Output Delay To Set Interrupt From MODEM Input Delay To Reset Interrupt From IOR# MHz MHz ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns 31 XR16V554/554D 2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO AC ELECTRICAL CHARACTERISTICS TA = -40O TO +85OC, VCC IS 2.25 TO 3.6V, 70 PF LOAD WHERE APPLICABLE SYMBOL PARAMETER LIMITS 2.5V ± 10% MAX MIN 1 45 45 8 24 45 1 45 45 8 40 40 16X data rate 8 LIMITS 3.3V ± 10% MAX MIN 1 45 45 24 45 1 45 45 8 UNIT REV. 1.0.2 TSSI TRRI TSI TINT TWRI TSSR TRR TWT TSRT TRST Bclk Delay From Stop To Set Interrupt Delay From IOR# To Reset Interrupt Delay From Start To Interrupt Delay From Initial INT Reset To Transmit Start Delay From IOW# To Reset Interrupt Delay From Stop To Set RXRDY# Delay From IOR# To Reset RXRDY# Delay From IOW# To Set TXRDY# Delay From Center of Start To Reset TXRDY# Reset Pulse Width Baud Clock Bclk ns ns Bclk ns Bclk ns ns Bclk ns Hz FIGURE 12. CLOCK TIMING CLK CLK EXTERNAL CLOCK OSC 32 XR16V554/554D REV. 1.0.2 2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO FIGURE 13. MODEM INPUT/OUTPUT TIMING FOR CHANNELS A-D IO W # IO W A c t iv e TW RTS# DTR# C h a n g e o f s ta te DO C h a n g e o f s ta te CD# CTS# DSR# TMOD IN T C h a n g e o f s ta te C h a n g e o f s ta te TMOD A c t iv e T RSI A c t iv e A c t iv e IO R # A c t iv e A c t iv e A c t iv e TMOD R I# C h a n g e o f s ta te FIGURE 14. 16 MODE (INTEL) DATA BUS READ TIMING FOR CHANNELS A-D A0-A7 TAS Valid Address TAS Valid Address TCS CS# TAH TCS TAH TDY TRD IOR# TRD TRDV D0-D7 Valid Data TDD TRDV Valid Data TDD RDTm 33 XR16V554/554D 2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO REV. 1.0.2 FIGURE 15. 16 MODE (INTEL) DATA BUS WRITE TIMING FOR CHANNELS A-D A0-A7 TAS Valid Address TAS Valid Address TCS CS# TAH TCS TAH TDY TWR IOW# TWR TDS D0-D7 Valid Data TDH TDS Valid Data TDH 16Write FIGURE 16. 68 MODE (MOTOROLA) DATA BUS READ TIMING FOR CHANNELS A-D A0-A7 TADS Valid Address Valid Address TCSL TADH CS# TRWS TCSD R/W# TRWH TRDH TRDA D0-D7 Valid Data Valid Data 68Read 34 XR16V554/554D REV. 1.0.2 2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO FIGURE 17. 68 MODE (MOTOROLA) DATA BUS WRITE TIMING FOR CHANNELS A-D A0-A7 TADS Valid Address Valid Address TCSL TADH CS# TRWS TCSD R/W# TRWH TWDS D0-D7 Valid Data T WDH Valid Data 68Write FIGURE 18. RECEIVE READY & INTERRUPT TIMING [NON-FIFO MODE] FOR CHANNELS A-D RX Start Bit Stop Bit TSSR 1 Byte in RHR TSSR D0:D7 D0:D7 TSSR 1 Byte in RHR TSSR D0:D7 TSSR 1 Byte in RHR TSSR INT RXRDY# Active Data Ready TRR Active Data Ready TRR Active Data Ready TRR IOR# (Reading data out of RHR) RXNFM 35 XR16V554/554D 2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO FIGURE 19. TRANSMIT READY & INTERRUPT TIMING [NON-FIFO MODE] FOR CHANNELS A-D TX (Unloading) IER[1] enabled Start Bit Stop Bit REV. 1.0.2 D0:D7 D0:D7 D0:D7 ISR is read ISR is read ISR is read INT* TWRI TSRT TWRI TSRT TWRI TSRT TXRDY# TWT TWT TWT IOW# (Loading data into THR) *INT is cleared when the ISR is read or when data is loaded into the THR. TXNonFIFO FIGURE 20. RECEIVE READY & INTERRUPT TIMING [FIFO MODE, DMA DISABLED] FOR CHANNELS A-D Start Bit RX S D0:D7 Stop Bit S D0:D7 T D0:D7 TSSI S D0:D7 T S D0:D7 T S D0:D7 T S D0:D7 T RX FIFO drops below RX Trigger Level INT TSSR RXRDY# First Byte is Received in RX FIFO IOR# (Reading data out of RX FIFO) RX FIFO fills up to RX Trigger Level or RX Data Timeout FIFO Empties TRRI TRR RXINTDMA# 36 XR16V554/554D REV. 1.0.2 2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO FIGURE 21. RECEIVE READY & INTERRUPT TIMING [FIFO MODE, DMA ENABLED] FOR CHANNELS A-D Start Bit Stop Bit RX S D0:D7 S D0:D7 T D0:D7 TSSI S D0:D7 T S D0:D7 T S D0:D7 T S D0:D7 T RX FIFO drops below RX Trigger Level INT RX FIFO fills up to RX Trigger Level or RX Data Timeout RXRDY# TSSR FIFO Empties TRRI TRR IOR# (Reading data out of RX FIFO) RXFIFODMA FIGURE 22. TRANSMIT READY & INTERRUPT TIMING [FIFO MODE, DMA MODE DISABLED] FOR CHANNELS A-D Stop Bit TX FIFO Empty Start Bit Last Data Byte Transmitted S D0:D7 T S D0:D7 T TSI T S D0:D7 T S D0:D7 T ISR is read TSRT S D0:D7 T TX (Unloading) IER[1] enabled S D0:D7 T ISR is read INT* TX FIFO fills up to trigger level Data in TX FIFO TX FIFO Empty TWRI TX FIFO drops below trigger level TXRDY# TWT IOW# (Loading data into FIFO) *INT is cleared when the ISR is read or when TX FIFO fills up to the trigger level. TXDMA# 37 XR16V554/554D 2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO REV. 1.0.2 FIGURE 23. TRANSMIT READY & INTERRUPT TIMING [FIFO MODE, DMA MODE ENABLED] FOR CHANNELS A-D Start Bit Stop Bit Last Data Byte Transmitted D0:D7 S D0:D7 T S D0:D7 T S D0:D7 T S D0:D7 T ISR Read TX (Unloading) IER[1] enabled S D0:D7 T S D0:D7 T ISR Read TSRT TSI INT* TX FIFO fills up to trigger level TX FIFO drops below trigger level At least 1 empty location in FIFO TWRI TX FIFO Full TXRDY# TWT IOW# (Loading data into FIFO) *INT cleared when the ISR is read or when TX FIFO fills up to trigger level. TXDMA 38 XR16V554/554D REV. 1.0.2 2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO PACKAGE DIMENSIONS 48 LEAD QUAD FLAT NO LEAD (7 x 7 x 0.9 mm, 0.50 mm pitch QFN) Note: The actual center pad is metallic and the size (D2) is device-dependent with a typical tolerance of 0.3mm. The lead may be half-etched terminal. Note: The control dimension is the millimeter column INCHES SYMBOL A A1 A3 D D2 b e L k MIN 0.031 0.000 0.006 0.270 0.201 0.007 MAX 0.039 0.002 0.010 0.281 0.209 0.012 MILLIMETERS MIN 0.80 0.00 0.15 6.85 5.10 0.18 MAX 1.00 0.05 0.25 7.15 5.30 0.30 0.0197 BSC 0.012 0.008 0.020 - 0.50 BSC 0.30 0.20 0.50 - 39 XR16V554/554D 2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO 64 LEAD LOW-PROFILE QUAD FLAT PACK (10 x 10 x 1.4 mm LQFP) D D1 48 33 REV. 1.0.2 49 32 D1 D 64 17 1 16 A2 e B A Seating Plane A1 L C α Note: The control dimension is the millimeter column INCHES SYMBOL A A1 A2 B C D D1 e L α MIN 0.055 0.002 0.053 0.007 0.004 0.465 0.390 MAX 0.063 0.006 0.057 0.011 0.008 0.480 0.398 MILLIMETERS MIN 1.40 0.05 1.35 0.17 0.09 11.80 9.90 MAX 1.60 0.15 1.45 0.27 0.20 12.20 10.10 0.020 BSC 0.018 0° 0.030 7° 0.50 BSC 0.45 0° 0.75 7° 40 XR16V554/554D REV. 1.0.2 2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO 68 LEAD PLASTIC LEADED CHIP CARRIER (PLCC) D D1 45 x H ° 1 C Seating Plane 45 x H ° 2 A2 2 1 68 B1 B D D1 D3 D2 e R D3 A1 A Note: The control dimension is the inch column INCHES SYMBOL A A1 A2 B B1 C D D1 D2 D3 e H1 H2 R MILLIMETERS MIN 4.19 2.29 0.51 0.33 0.66 0.19 25.02 24.13 22.61 MIN 0.165 0.090 0.020 0.013 0.026 0.008 0.985 0.950 0.890 MAX 0.200 0.130 ---. 0.021 0.032 0.013 0.995 0.958 0.930 MAX 5.08 3.30 --0.53 0.81 0.32 25.27 24.33 23.62 0.800 typ. 0.050 BSC 0.042 0.042 0.025 0.056 0.048 0.045 1.07 1.07 0.64 20.32 typ. 1.27 BSC 1.42 1.22 1.14 41 XR16V554/554D 2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO 80 LEAD PLASTIC QUAD FLAT PACK (12 mm x 12 mm LQFP, 1.4 mm Form) REV. 1.0.2 Note: The control dimension is the millimeter column INCHES SYMBOL A A1 A2 B C D D1 e L α MIN 0.055 0.002 0.053 0.007 0.004 0.543 0.465 MAX 0.063 0.006 0.057 0.011 0.008 0.559 0.480 MILLIMETERS MIN 1.40 0.05 1.35 0.17 0.09 13.80 11.80 MAX 1.60 0.15 1.45 0.27 0.20 14.20 12.20 0.0197 BSC 0.018 0° 0.030 7° 0.50 BSC 0.45 0° 0.75 7° 42 XR16V554/554D REV. 1.0.2 2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO REVISION HISTORY DATE April 2006 July 2006 October 2006 January 2007 May 2007 September 2007 REVISION Rev P1.0.0 Rev P1.0.1 Rev P1.0.2 Rev 1.0.0 Rev 1.0.1 Rev 1.0.2 Preliminary Data Sheet. Updated AC Electrical Characterstics. Updated DC Electrical Characteristics. Final Datasheet. Updated QFN package dimensions drawing to show minimum "k" parameter. Changed 80-pin LQFP package pin out assignment. DESCRIPTION NOTICE EXAR Corporation reserves the right to make changes to the products contained in this publication in order to improve design, performance or reliability. EXAR Corporation assumes no responsibility for the use of any circuits described herein, conveys no license under any patent or other right, and makes no representation that the circuits are free of patent infringement. Charts and schedules contained here in are only for illustration purposes and may vary depending upon a user’s specific application. While the information in this publication has been carefully checked; no responsibility, however, is assumed for inaccuracies. EXAR Corporation does not recommend the use of any of its products in life support applications where the failure or malfunction of the product can reasonably be expected to cause failure of the life support system or to significantly affect its safety or effectiveness. Products are not authorized for use in such applications unless EXAR Corporation receives, in writing, assurances to its satisfaction that: (a) the risk of injury or damage has been minimized; (b) the user assumes all such risks; (c) potential liability of EXAR Corporation is adequately protected under the circumstances. Copyright 2007 EXAR Corporation Datasheet September 2007. Send your UART technical inquiry with technical details to hotline: uarttechsupport@exar.com. Reproduction, in part or whole, without the prior written consent of EXAR Corporation is prohibited. 43 XR16V554/554D REV. 1.0.2 2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO TABLE OF CONTENTS GENERAL DESCRIPTION................................................................................................ 1 FEATURES .................................................................................................................................................... 1 APPLICATIONS .............................................................................................................................................. 1 FIGURE 1. XR16V554 BLOCK DIAGRAM ........................................................................................................................................... 1 FIGURE 2. PIN OUT ASSIGNMENT FOR 68-PIN PLCC PACKAGES IN 16 AND 68 MODE AND 64-PIN LQFP PACKAGES ......................... 2 FIGURE 3. PIN OUT ASSIGNMENT FOR 48-PIN QFN PACKAGE AND 80-PIN LQFP PACKAGE ............................................................... 3 PIN DESCRIPTIONS ......................................................................................................... 4 ORDERING INFORMATION ............................................................................................................................... 4 1.0 PRODUCT DESCRIPTION ...................................................................................................................... 9 2.0 FUNCTIONAL DESCRIPTIONS ............................................................................................................ 10 2.1 CPU INTERFACE .............................................................................................................................................. 10 FIGURE 4. XR16V554 TYPICAL INTEL/MOTOROLA DATA BUS INTERCONNECTIONS........................................................................... 10 2.2 DEVICE RESET ................................................................................................................................................. 11 2.3 CHANNEL SELECTION .................................................................................................................................... 11 TABLE 1: CHANNEL A-D SELECT IN 16 MODE ................................................................................................................................. 11 TABLE 2: CHANNEL A-D SELECT IN 68 MODE ................................................................................................................................. 11 2.4 CHANNELS A-D INTERNAL REGISTERS ....................................................................................................... 12 2.5 INT OUPUTS FOR CHANNELS A-D................................................................................................................. 12 TABLE 3: INT PIN OPERATION FOR TRANSMITTER FOR CHANNELS A-D ........................................................................................... 12 TABLE 4: INT PIN OPERATION FOR RECEIVER FOR CHANNELS A-D ................................................................................................. 12 2.6 DMA MODE ....................................................................................................................................................... 12 TABLE 5: TXRDY# AND RXRDY# OUTPUTS IN FIFO AND DMA MODE FOR CHANNELS A-D ........................................................... 13 2.7 CRYSTAL OSCILLATOR OR EXTERNAL CLOCK INPUT.............................................................................. 13 FIGURE 5. TYPICAL CRYSTAL CONNECTIONS .................................................................................................................................. 13 2.8 PROGRAMMABLE BAUD RATE GENERATOR.............................................................................................. 13 FIGURE 6. BAUD RATE GENERATOR ............................................................................................................................................... 14 TABLE 6: TYPICAL DATA RATES WITH A 14.7456 MHZ CRYSTAL OR EXTERNAL CLOCK ...................................................................... 14 2.9 TRANSMITTER.................................................................................................................................................. 14 2.9.1 TRANSMIT HOLDING REGISTER (THR) - WRITE ONLY........................................................................................... 2.9.2 TRANSMITTER OPERATION IN NON-FIFO MODE .................................................................................................... FIGURE 7. TRANSMITTER OPERATION IN NON-FIFO MODE .............................................................................................................. 2.9.3 TRANSMITTER OPERATION IN FIFO MODE ............................................................................................................. FIGURE 8. TRANSMITTER OPERATION IN FIFO AND FLOW CONTROL MODE ..................................................................................... 15 15 15 15 15 2.10 RECEIVER ....................................................................................................................................................... 16 2.10.1 RECEIVE HOLDING REGISTER (RHR) - READ-ONLY ............................................................................................ 16 FIGURE 9. RECEIVER OPERATION IN NON-FIFO MODE .................................................................................................................... 16 FIGURE 10. RECEIVER OPERATION IN FIFO.................................................................................................................................... 17 2.11 INTERNAL LOOPBACK................................................................................................................................. 18 FIGURE 11. INTERNAL LOOP BACK IN CHANNEL A AND B ................................................................................................................ 18 3.0 UART INTERNAL REGISTERS............................................................................................................. 19 TABLE 7: UART CHANNEL A AND B UART INTERNAL REGISTERS ...................................................................................... 19 TABLE 8: INTERNAL REGISTERS DESCRIPTION. ................................................................................................................... 20 4.0 INTERNAL REGISTER DESCRIPTIONS .............................................................................................. 20 4.1 RECEIVE HOLDING REGISTER (RHR) - READ- ONLY .................................................................................. 20 4.2 TRANSMIT HOLDING REGISTER (THR) - WRITE-ONLY ............................................................................... 20 4.3 INTERRUPT ENABLE REGISTER (IER) - READ/WRITE ................................................................................ 20 4.3.1 IER VERSUS RECEIVE FIFO INTERRUPT MODE OPERATION ............................................................................... 21 4.3.2 IER VERSUS RECEIVE/TRANSMIT FIFO POLLED MODE OPERATION.................................................................. 21 4.4 INTERRUPT STATUS REGISTER (ISR)........................................................................................................... 22 4.4.1 INTERRUPT GENERATION: ........................................................................................................................................ 22 4.4.2 INTERRUPT CLEARING: ............................................................................................................................................. 22 TABLE 9: INTERRUPT SOURCE AND PRIORITY LEVEL ....................................................................................................................... 22 4.5 FIFO CONTROL REGISTER (FCR) - WRITE-ONLY ........................................................................................ 23 TABLE 10: RECEIVE FIFO TRIGGER LEVEL SELECTION ................................................................................................................... 23 4.6 LINE CONTROL REGISTER (LCR) - READ/WRITE ........................................................................................ 24 TABLE 11: PARITY SELECTION ........................................................................................................................................................ 25 4.7 MODEM CONTROL REGISTER (MCR) OR GENERAL PURPOSE OUTPUTS CONTROL - READ/WRITE . 25 TABLE 12: INT OUTPUT MODES ..................................................................................................................................................... 26 4.8 LINE STATUS REGISTER (LSR) - READ/WRITE ............................................................................................ 26 4.9 MODEM STATUS REGISTER (MSR) - READ/WRITE...................................................................................... 27 I XR16V554/554D 2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO REV. 1.0.2 4.10 SCRATCH PAD REGISTER (SPR) - READ/WRITE ....................................................................................... 28 4.11 BAUD RATE GENERATOR REGISTERS (DLL AND DLM) - READ/WRITE................................................. 28 TABLE 13: UART RESET CONDITIONS FOR CHANNELS A-D .................................................................................................. 29 ABSOLUTE MAXIMUM RATINGS.................................................................................. 30 TYPICAL PACKAGE THERMAL RESISTANCE DATA (MARGIN OF ERROR: ± 15%) 30 ELECTRICAL CHARACTERISTICS ............................................................................... 30 DC ELECTRICAL CHARACTERISTICS ............................................................................................................. 30 AC ELECTRICAL CHARACTERISTICS ............................................................................................................. 31 TA = -40O TO +85OC, VCC IS 2.25 TO 3.6V, 70 PF LOAD WHERE APPLICABLE ............................................. 31 FIGURE 12. CLOCK TIMING ............................................................................................................................................................. 32 FIGURE 13. MODEM INPUT/OUTPUT TIMING FOR CHANNELS A-D .................................................................................................... 33 FIGURE 14. 16 MODE (INTEL) DATA BUS READ TIMING FOR CHANNELS A-D.................................................................................... 33 FIGURE 15. 16 MODE (INTEL) DATA BUS WRITE TIMING FOR CHANNELS A-D .................................................................................. 34 FIGURE 16. 68 MODE (MOTOROLA) DATA BUS READ TIMING FOR CHANNELS A-D........................................................................... 34 FIGURE 18. RECEIVE READY & INTERRUPT TIMING [NON-FIFO MODE] FOR CHANNELS A-D ............................................................ 35 FIGURE 17. 68 MODE (MOTOROLA) DATA BUS WRITE TIMING FOR CHANNELS A-D ......................................................................... 35 FIGURE 19. TRANSMIT READY & INTERRUPT TIMING [NON-FIFO MODE] FOR CHANNELS A-D .......................................................... 36 FIGURE 20. RECEIVE READY & INTERRUPT TIMING [FIFO MODE, DMA DISABLED] FOR CHANNELS A-D........................................... 36 FIGURE 21. RECEIVE READY & INTERRUPT TIMING [FIFO MODE, DMA ENABLED] FOR CHANNELS A-D............................................ 37 FIGURE 22. TRANSMIT READY & INTERRUPT TIMING [FIFO MODE, DMA MODE DISABLED] FOR CHANNELS A-D............................... 37 FIGURE 23. TRANSMIT READY & INTERRUPT TIMING [FIFO MODE, DMA MODE ENABLED] FOR CHANNELS A-D ............................... 38 PACKAGE DIMENSIONS ................................................................................................................................ 39 REVISION HISTORY...................................................................................................................................... 43 II
        下载 PDF
        XR16V554IV 价格&库存
        -> 查询更多价格&库存

        很抱歉，暂时无法提供与“XR16V554IV”相匹配的价格&库存，您可以联系我们找货

        免费人工找货

        相关技术文章

        华秋（原“华强聚丰”）：
        电子发烧友
        华秋开发
        华秋电路(原"华强PCB")
        华秋商城(原"华强芯城")
        华秋智造
        My ElecFans
        APP
        网站地图
        设计技术
        可编程逻辑
        电源/新能源
        MEMS/传感技术
        测量仪表
        嵌入式技术
        制造/封装
        模拟技术
        RF/无线
        接口/总线/驱动
        处理器/DSP
        EDA/IC设计
        存储技术
        光电显示
        EMC/EMI设计
        连接器
        行业应用
        LEDs
        汽车电子
        音视频及家电
        通信网络
        医疗电子
        人工智能
        虚拟现实
        可穿戴设备
        机器人
        安全设备/系统
        军用/航空电子
        移动通信
        工业控制
        便携设备
        触控感测
        物联网
        智能电网
        区块链
        新科技
        特色内容
        专栏推荐
        学院
        设计资源
        设计技术
        电子百科
        电子视频
        元器件知识
        工具箱
        VIP会员
        社区
        小组
        论坛
        问答
        评测试用
        企业服务
        产品
        资料
        文章
        方案
        企业
        供应链服务
        硬件开发
        华秋电路
        华秋商城
        华秋智造
        nextPCB
        BOM配单
        媒体服务
        网站广告
        在线研讨会
        活动策划
        新闻发布
        新品发布
        小测验
        设计大赛
        华秋
        关于我们
        投资关系
        新闻动态
        加入我们
        联系我们
        侵权投诉
        社交网络
        微博
        移动端
        发烧友APP
        硬声APP
        WAP
        联系我们
        广告合作
        王婉珠：wangwanzhu@elecfans.com
        内容合作
        黄晶晶：huangjingjing@elecfans.com
        内容合作（海外）
        张迎辉：mikezhang@elecfans.com
        供应链服务 PCB/IC/PCBA
        江良华：lanhu@huaqiu.com
        投资合作
        曾海银：zenghaiyin@huaqiu.com
        社区合作
        刘勇：liuyong@huaqiu.com
        华秋发烧友
        电子工程师社区
        华秋电路
        1-32层PCB打样·中小批量
        华秋商城
        元器件现货·全球代购·SmartBOM
        华秋智造
        SMT贴片·PCBA加工
        NextPCB
        PCB Manufacturer

        版权所有 © 湖南华秋数字科技有限公司

        电子发烧友（电路图）湘公网安备 43011202000918 号电信与信息服务业务经营许可证：合字B2-20210191工商网监认证工商网监 湘ICP备2023018690号