XR16V698

XR16V698 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO JULY 2008 REV. 1.0.3 GENERAL DESCRIPTION The XR16V6981 (698), is a 2.25V to 3.6V octal Universal Asynchronous Receiver and Transmitter (UART) with 5V tolerant inputs. The highly integrated device is designed for high bandwidth requirement in communication systems. The global interrupt source register provides a complete interrupt status indication for all 8 channels to speed up interrupt parsing. Each UART has its own 16C550 compatible set of configuration registers, TX and RX FIFOs of 32 bytes, fully programmable transmit and receive FIFO trigger levels, automatic RTS/CTS or DTR/DSR hardware flow control with programmable hysteresis, automatic software (Xon/Xoff) flow control, RS-485 half-duplex direction control with programmable turnaround delay, Intel or Motorola bus interface and sleep mode with a wake-up indicator. NOTE: Covered by US patents #5,649,122 and #5,949,787 FEATURES • 2.25V to 3.6V with 5V Tolerant Inputs • Single Interrupt output for all 8 UARTs • A Global Interrupt Source Register for all 8 UARTs • 5G “Flat” UART Registers for easier programming • Simultaneous Initialization of all UART channels • General Purpose 16-bit Timer/counter • Sleep Mode with Wake-up Indication • Highly Integrated Device for Space Saving • Each UART is independently controlled with: ■ ■ ■ ■ ■ ■ ■ 16C550 Compatible 5G Register Set 32-byte Transmit and Receive FIFOs Fractional Baud Rate Generator Programmable TX and RX FIFO Trigger Level Automatic RTS/CTS or DTR/DSR Flow Control Automatic Xon/Xoff Software Flow Control RS-485 Half-Duplex Direction Control Output with Selectable Turn-around Delay Infrared (IrDA 1.0) Data Encoder/Decoder Programmable Data Rate with Prescaler APPLICATIONS • Remote Access Servers • Ethernet Network to Serial Ports • Network Management • Factory Automation and Process Control • Point-of-Sale Systems • Multi-port RS-232/RS-422/RS-485 Cards FIGURE 1. BLOCK DIAGRAM ■ ■ • Up to 15 Mbps Serial Data Rate • Pin compatible to XR16V798. Same 100-pin QFP Package (14x20x3 mm) UART Channel 0 UART Regs BRG 32 Byte TX FIFO TX & RX IR ENDEC TX0, RX0, DTR0#, DSR0#, RTS0#, CTS0#, CD0#, RI0# RST# A7:A0 D7:D0 IOR# IOW# CS# INT# 16/68# Data Bus Interface Device Configuration Registers 32 Byte RX FIFO UART Channel 1 UART Channel 2 UART Channel 3 UART Channel 4 UART Channel 5 UART Channel 6 16-bit Timer/Counter UART Channel 7 TX7, RX7, DTR7#, DSR7#, RTS7#, CTS7#, CD7#, RI7# XTAL1 XTAL2 TMRCK Crystal Osc/Buffer Exar Corporation 48720 Kato Road, Fremont CA, 94538 • (510) 668-7000 • FAX (510) 668-7017 • www.exar.com XR16V698 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO REV. 1.0.3 FIGURE 2. PIN OUT OF THE DEVICE TX2 DTR2# RTS2# RI2# CD2# DSR2# CTS2# RX2 TX3 DTR3# RTS3# RI3# CD3# DSR3# CTS3# RX3 TX4 DTR4# RTS4# RI4# CD4# DSR4# CTS4# RX4 TX5 DTR5# RTS5# RI5# CD5# DSR5# XTAL2 XTAL1 GND VCC TX1 DTR1# RTS1# RI1# CD1# DSR1# CTS1# RX1 TX0 DTR0# RTS0# RI0# CD0# DSR0# CTS0# RX0 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 XR16V698 100-QFP CTS5# RX5 VCC GND TX6 DTR6# RTS6# RI6# CD6# DSR6# CTS6# RX6 TX7 DTR7# RTS7# RI7# CD7# DSR7# CTS7# RX7 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 RST# 16/68# VCC GND D7 D6 D5 D4 D3 D2 D1 D0 IOW# TMRCK ENIR ORDERING INFORMATION PART NUMBER XR16V698IQ100 PACKAGE 100-Lead QFP OPERATING TEMPERATURE RANGE -40°C to +85°C DEVICE STATUS Active 2 INT# VCC GND IOR# A7 A6 A5 A4 A3 A2 A1 A0 VCC GND CS# XR16V698 REV. 1.0.3 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO PIN DESCRIPTIONS NAME PIN # TYPE DESCRIPTION DATA BUS INTERFACE A7:A0 20-27 I Address lines [7:0]. A0:A3 selects individual UART’s 16 configuration registers, A4:A6 selects UART channel 0 to7, and A7 selects the global device configuration registers. Data bus lines [7:0] (bidirectional). When 16/68# pin is HIGH, it selects Intel bus interface and this input is read strobe (active LOW). The falling edge instigates an internal read cycle and retrieves the data byte from an internal register pointed by the address lines [A7:A0], places it on the data bus to allow the host processor to read it on the leading edge. When 16/68# pin is LOW, it selects Motorola bus interface and this input should be connected to VCC. When 16/68# pin is HIGH, it selects Intel bus interface and this input becomes write strobe (active LOW). The falling edge instigates the internal write cycle and the leading edge transfers the data byte on the data bus to an internal register pointed by the address lines. When 16/68# pin is LOW, it selects Motorola bus interface and this input becomes read (HIGH) and write (LOW) signal (R/W#). When 16/68# pin is HIGH, this input is chip select (active LOW) to enable the XR16V698 device. When 16/68# pin is LOW, this input becomes the read and write strobe (active LOW) for the Motorola bus interface. Global interrupt output from XR16V698 (open drain, active LOW). This output requires an external pull-up resistor (47K-100K ohms) to operate properly. It may be shared with other devices in the system to form a single interrupt line to the host processor and have the software driver polls each device for the interrupt status. D7:D0 IOR# 5-12 19 IO I IOW# (R/W#) 13 I CS# 30 I INT# 16 OD MODEM OR SERIAL I/O INTERFACE TX0 RX0 93 100 O I UART channel 0 Transmit Data or infrared transmit data. UART channel 0 Receive Data or infrared receive data. Normal RXD input idles HIGH. The infrared pulse can be inverted internally prior to decoding by setting FCTR bit-4. UART channel 0 Request to Send or general purpose output (active LOW). This port may be used for one of two functions: 1) Auto hardware flow control, see EFR bit-6, MCR bits-1 & 2, FCTR bits 0-3 and IER bit-6 2) RS-485 half-duplex direction control, see FCTR bit-5, MCR bit-2 and MSR bits 07. UART channel 0 Clear to Send or general purpose input (active LOW). It can be used for auto hardware flow control, see EFR bit-7, MCR bit-2 and IER bit-7. UART channel 0 Data Terminal Ready or general purpose output (active LOW). This port may be used forone of two functions. 1) auto hardware flow control, see EFR bit-6, FCTR bits-0 to 3, MCR bits-0 & 2, and IER bit-6 2) RS-485 half-duplex direction control, see FCTR bit-5, MCR bit-2 and MSR bits 07. UART channel 0 Data Set Ready or general purpose input (active LOW). It can be used for auto hardware flow control, see EFR bit-7, MCR bit-2 and IER bit-7. UART channel 0 Carrier Detect or general purpose input (active LOW). RTS0# 95 O CTS0# DTR0# 99 94 I O DSR0# CD0# 98 97 I I 3 XR16V698 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO REV. 1.0.3 NAME RI0# TX1 RX1 PIN # 96 85 92 TYPE I O I DESCRIPTION UART channel 0 Ring Indicator or general purpose input (active LOW). UART channel 1 Transmit Data or infrared transmit data. UART channel 1 Receive Data or infrared receive data. Normal RXD input idles HIGH. The infrared pulse can be inverted internally prior to decoding by setting FCTR bit-4. UART channel 1 Request to Send or general purpose output (active LOW). See description of RTS0# pin. UART channel 1 Clear to Send or general purpose input (active LOW). See description of CTS0# pin. UART channel 1 Data Terminal Ready or general purpose output (active LOW). See description of DTR0# pin. UART channel 1 Data Set Ready or general purpose input (active LOW). See description of DSR0# pin. UART channel 1 Carrier Detect or general purpose input (active LOW). UART channel 1 Ring Indicator or general purpose input (active LOW). UART channel 2 Transmit Data or infrared transmit data. UART channel 2 Receive Data or infrared receive data. Normal RXD input idles HIGH. The infrared pulse can be inverted internally prior to decoding by setting FCTR bit-4. UART channel 2 Request to Send or general purpose output (active LOW). See description of RTS0# pin. UART channel 2 Clear to Send or general purpose input (active LOW). See description of CTS0# pin. UART channel 2 Data Terminal Ready or general purpose output (active LOW). See description of DTR0# pin. UART channel 2 Data Set Ready or general purpose input (active LOWactive LOW). See description of DSR0# pin. UART channel 2 Carrier Detect or general purpose input (active LOW). UART channel 2 Ring Indicator or general purpose input (active LOW). UART channel 3 Transmit Data or infrared transmit data. UART channel 3 Receive Data or infrared receive data. Normal RXD input idles HIGH. The infrared pulse can be inverted internally prior to decoding by setting FCTR bit-4. UART channel 3 Request to Send or general purpose output (active LOW). See description of RTS0# pin. UART channel 3 Clear to Send or general purpose input (active LOW). See description of CTS0# pin. UART channel 3 Data Terminal Ready or general purpose output (active LOW). See description of DTR0# pin. UART channel 3 Data Set Ready or general purpose input (active LOW). See description of DSR0# pin. UART channel 3 Carrier Detect or general purpose input (active LOW). UART channel 3 Ring Indicator or general purpose input (active LOW). RTS1# CTS1# DTR1# DSR1# CD1# RI1# TX2 RX2 87 91 86 90 89 88 80 73 O I O I I I O I RTS2# CTS2# DTR2# DSR2# CD2# RI2# TX3 RX3 78 74 79 75 76 77 72 65 O I O I I I O I RTS3# CTS3# DTR3# DSR3# CD3# RI3# 70 66 71 67 68 69 O I O I I I 4 XR16V698 REV. 1.0.3 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO NAME TX4 RX4 PIN # 64 57 TYPE O I DESCRIPTION UART channel 4 Transmit Data or infrared transmit data. UART channel 4 Receive Data or infrared receive data. Normal RXD input idles HIGH. The infrared pulse can be inverted internally prior to decoding by setting FCTR bit-4. UART channel 4 Request to Send or general purpose output (active LOW). See description of RTS0# pin. UART channel 4 Clear to Send or general purpose input (active LOW). See description of CTS0# pin. UART channel 4 Data Terminal Ready or general purpose output (active LOW). See description of DTR0# pin. UART channel 4 Data Set Ready or general purpose input (active LOW). See description of DSR0# pin. UART channel 4 Carrier Detect or general purpose input (active LOW). UART channel 4 Ring Indicator or general purpose input (active LOW). UART channel 5 Transmit Data or infrared transmit data. UART channel 5 Receive Data or infrared receive data. Normal RXD input idles HIGH. The infrared pulse can be inverted internally prior to decoding by setting FCTR bit-4. UART channel 5 Request to Send or general purpose output (active LOW). See description of RTS0# pin. UART channel 5 Clear to Send or general purpose input (active LOW). See description of CTS0# pin. UART channel 5 Data Terminal Ready or general purpose output (active LOW). See description of DTR0# pin. UART channel 5 Data Set Ready or general purpose input (active LOW). See description of DSR0# pin. UART channel 5 Carrier Detect or general purpose input (active LOW). UART channel 5 Ring Indicator or general purpose input (active LOW). UART channel 6 Transmit Data or infrared transmit data. UART channel 6 Receive Data or infrared receive data. Normal RXD input idles HIGH. The infrared pulse can be inverted internally prior to decoding by setting FCTR bit-4. UART channel 6 Request to Send or general purpose output (active LOW). See description of RTS0# pin. UART channel 6 Clear to Send or general purpose input (active LOW). See description of CTS0# pin. UART channel 6 Data Terminal Ready or general purpose output (active LOW). See description of DTR0# pin. UART channel 6 Data Set Ready or general purpose input (active LOW). See description of DSR0# pin. UART channel 6 Carrier Detect or general purpose input (active LOW). UART channel 6 Ring Indicator or general purpose input (active LOW). UART channel 7 Transmit Data or infrared transmit data. RTS4# CTS4# DTR4# DSR4# CD4# RI4# TX5 RX5 62 58 63 59 60 61 56 49 O I O I I I O I RTS5# CTS5# DTR5# DSR5# CD5# RI5# TX6 RX6 54 50 55 51 52 53 46 39 O I O I I I O I RTS6# CTS6# DTR6# DSR6# CD6# RI6# TX7 44 40 45 41 42 43 38 O I O I I I O 5 XR16V698 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO REV. 1.0.3 NAME RX7 PIN # 31 TYPE I DESCRIPTION UART channel 7 Receive Data or infrared receive data. Normal RXD input idles HIGH. The infrared pulse can be inverted internally prior to decoding by setting FCTR bit-4. UART channel 7 Request to Send or general purpose output (active LOW). See description of RTS0# pin. UART channel 7 Clear to Send or general purpose input (active LOW). See description of CTS0# pin. UART channel 7 Data Terminal Ready or general purpose output (active LOW). See description of DTR0# pin. UART channel 7 Data Set Ready or general purpose input (active LOW). See description of DSR0# pin. UART channel 7 Carrier Detect or general purpose input (active LOW). UART channel 7 Ring Indicator or general purpose input (active LOW). RTS7# CTS7# DTR7# DSR7# CD7# RI7# 36 32 37 33 34 35 O I O I I I ANCILLARY SIGNALS XTAL1 XTAL2 TMRCK ENIR 82 81 14 15 I O I I Crystal or external clock input. Caution: this input is not 5V tolerant. Crystal or buffered clock output. 16-bit timer/counter external clock input. Infrared mode enable (active HIGH). This pin is sampled during power up, following a hardware reset (RST#) or soft-reset (register RESET). It can be used to start up all 8 UARTs in the infrared mode. The sampled logic state is transferred to MCR bit-6 in the UART. Reset (active LOW). The XR16V698 does not have a Power-on reset. Therefore, a hardware reset must be issued using this pin during power-up. The configuration and UART registers are reset to default values, see Table 18. Intel or Motorola data bus interface select. The Intel bus interface is selected when this input is HIGH and the Motorola bus interface is selected when this input is LOW. This input affects the functionality of IOR#, IOW# and CS# pins. +2.25V to 3.6V supply with 5V tolerant serial (modem) inputs. Power supply common, ground. RST# 1 I 16/68# 2 I VCC GND 3,17,28,48,84 4,18,29,47,83 NOTE: Pin type: I=Input, O=Output, IO= Input/output, OD=Output Open Drain. 6 XR16V698 REV. 1.0.3 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO 1.0 DESCRIPTION The XR16V698 (698) integrates the functions of 8 enhanced 16550 UARTs, a general purpose 16-bit timer/ counter and an on-chip oscillator. The device configuration registers include a set of four consecutive interrupt source registers that provides interrupt-status for all 8 UARTs, timer/counter and a sleep wake up indicator. Each UART channel has its own 16550 UART compatible configuration register set for individual channel control, status, and data transfer. Additionally, each UART channel has 32-byte of transmit and receive FIFOs, automatic RTS/CTS or DTR/DSR hardware flow control with hysteresis control, automatic Xon/Xoff and special character software flow control, programmable transmit and receive FIFO trigger levels, infrared encoder and decoder (IrDA ver. 1.0), programmable baud rate generator with a prescaler of divide by 1 or 4, and data rate up to 15Mbps with 4X sampling clock or 7.5Mbps with 8X sampling clock at 3.3V and 10Mbps with 4X sampling clock or 5Mbps with 8X sampling clock at 2.5V. The XR16V598 is a 2.25-3.6V device with 5 volt tolerant inputs (except XTAL1). 2.0 FUNCTIONAL DESCRIPTIONS 2.1 2.1.1 Device Reset Hardware Reset The RST# input resets the internal registers and the serial interface outputs in all 8 channels to their default state (see Table 18). A LOW pulse of longer than 40 ns duration will be required to activate the reset function in the device. 2.1.2 Software Reset The internal registers of each UART can be reset by writing to the RESET register in the Device Configuration Registers. For more details, see the RESET register description on page 29. 2.2 UART Channel Selection A LOW on the chip select pin, CS#, allows the user to select one of the UART channels to configure, send transmit data and/or unload receive data to/from the UART. When address line A7 = 0, address lines A6:A4 are used to select one of the eight channels. See Table 1 below for UART channel selection. TABLE 1: UART CHANNEL SELECTION A7 0 0 0 0 0 0 0 0 A6 0 0 0 0 1 1 1 1 A5 0 0 1 1 0 0 1 1 A4 0 1 0 1 0 1 0 1 FUNCTION Channel 0 Selected Channel 1 Selected Channel 2 Selected Channel 3 Selected Channel 4 Selected Channel 5 Selected Channel 6 Selected Channel 7 Selected 2.3 Simultaneous Write to All Channels During a write cycle, the setting of the Device Configuration register REGB (See Table 8) bit-0 to a logic 1 will override the channel selection of address A6:A4 and allow a simultaneous write to all 8 UART channels when any channel is written to. This functional capability allow the registers in all 8 UART channels to be modified concurrently, saving individual channel initialization time. Caution should be considered, however, when using this capability. Any in-process serial data transfer may be disrupted by changing an active channel’s mode. 7 XR16V698 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO 2.4 INT# Ouput REV. 1.0.3 The INT# interrupt output changes according to the operating mode and enhanced features setup. Table 2 and 3 summarize the operating behavior for the transmitter and receiver. TABLE 2: INT# PIN OPERATION FOR TRANSMITTER Auto RS-485 Mode NO FCR BIT-0 = 0 (FIFO DISABLED) HIGH = a byte in THR LOW = THR empty FCR BIT-0 = 1 (FIFO ENABLED) HIGH = FIFO above trigger level LOW = FIFO below trigger level or FIFO empty YES HIGH = a byte in THR HIGH = FIFO above trigger level LOW = transmitter empty LOW = FIFO below trigger level or transmitter empty TABLE 3: INT# PIN OPERATION FOR RECEIVER FCR BIT-0 = 0 (FIFO DISABLED) HIGH = no data LOW = 1 byte FCR BIT-0 = 1 (FIFO ENABLED) HIGH = FIFO below trigger level LOW = FIFO above trigger level 2.5 Crystal Oscillator The 698 includes an on-chip oscillator. The crystal oscillator provides the system clock to the Baud Rate Generators (BRG) in each of the 8 UARTs, the 16-bit general purpose timer/counter and internal logics. XTAL1 is the input to the oscillator or external clock buffer input with XTAL2 pin being the output. For programming details, see “Section 2.6, Programmable Baud Rate Generator with Fractional Divisor” on page 9. The on-chip oscillator is designed to use an industry standard microprocessor crystal (parallel resonant, fundamental frequency with 10-22 pF capacitance load, ESR of 20-120 ohms and 100ppm frequency tolerance) connected externally between the XTAL1 and XTAL2 pins (see Figure 3). Alternatively, an external clock can be connected to the XTAL1 pin to clock the internal 8 baud rate generators for standard or custom rates. The typical oscillator connections are shown in Figure 3. For further reading on oscillator circuit please see application note DAN108 on EXAR’s web site. FIGURE 3. TYPICAL OSCILLATOR CONNECTIONS R=300K to 400K XTAL1 24 MHz C1 22-47pF XTAL2 C2 22-47pF 8 XR16V698 REV. 1.0.3 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO 2.6 Programmable Baud Rate Generator with Fractional Divisor Each UART has its own Baud Rate Generator (BRG) with a prescaler for the transmitter and receiver. The prescaler is controlled by a software bit in the MCR register. The MCR register bit-7 sets the prescaler to divide the input crystal or external clock by 1 or 4. The output of the prescaler clocks to the BRG. The BRG further divides this clock by a programmable divisor between 1 and (216 - 0.0625) in increments of 0.0625 (1/16) to obtain a 16X or 8X or 4X sampling clock of the serial data rate. The sampling clock is used by the transmitter for data bit shifting and receiver for data sampling. The BRG divisor (DLL, DLM and DLD registers) defaults to the value of ’1’ (DLL = 0x01, DLM = 0x00 and DLD = 0x00) upon reset. Therefore, the BRG must be programmed during initialization to the operating data rate. The DLL and DLM registers provide the integer part of the divisor and the DLD register provides the fractional part of the dvisior. Only the four lower bits of the DLD are implemented and they are used to select a value from 0 (for setting 0000) to 0.9375 or 15/16 (for setting 1111). Programming the Baud Rate Generator Registers DLL, DLM and DLD provides the capability for selecting the operating data rate. Table 4 shows the standard data rates available with a 24MHz crystal or external clock at 16X clock rate. If the pre-scaler is used (MCR bit-7 = 1), the output data rate will be 4 times less than that shown in Table 4. At 8X sampling rate, these data rates would double. Also, when using 8X sampling mode, please note that the bit-time will have a jitter (+/- 1/16) whenever the DLD is non-zero and is an odd number. At 4X sampling rate, these data rates would quadruple. When using a non-standard data rate crystal or external clock, the divisor value can be calculated with the following equation(s): 8XMODE [7:0] = 0X00 4XMODE [7:0] = 0X00 8XMODE [7:0] = 0XFF 4XMODE [7:0] = 0X00 8XMODE [7:0] = 0X00 4XMODE [7:0] = 0XFF 8XMODE [7:0] = 0XFF 4XMODE [7:0] = 0XFF Required Divisor (decimal) = (XTAL1 clock frequency / prescaler) / (serial data rate x 16) Required Divisor (decimal) = (XTAL1 clock frequency / prescaler / (serial data rate x 8) Required Divisor (decimal) = (XTAL1 clock frequency / prescaler / (serial data rate x 4) Reserved. The closest divisor that is obtainable in the 698 can be calculated using the following formula: ROUND( (Required Divisor - TRUNC(Required Divisor) )*16)/16 + TRUNC(Required Divisor), where DLM = TRUNC(Required Divisor) >> 8 DLL = TRUNC(Required Divisor) & 0xFF DLD = ROUND( (Required Divisor-TRUNC(Required Divisor) )*16) In the formulas above, please note that: TRUNC (N) = Integer Part of N. For example, TRUNC (5.6) = 5. ROUND (N) = N rounded towards the closest integer. For example, ROUND (7.3) = 7 and ROUND (9.9) = 10. A >> B indicates right shifting the value ’A’ by ’B’ number of bits. For example, 0x78A3 >> 8 = 0x0078. 9 XR16V698 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO FIGURE 4. BAUD RATE GENERATOR To Other Channels REV. 1.0.3 DLL, DLM and DLD Registers Prescaler Divide by 1 XTAL1 XTAL2 Crystal Osc/ Buffer Prescaler Divide by 4 MCR Bit-7=0 (default) Fractional Baud Rate Generator Logic MCR Bit-7=1 16X or 8X or 4X Sampling Rate Clock to Transmitter and Receiver TABLE 4: TYPICAL DATA RATES WITH A 24 MHZ CRYSTAL OR EXTERNAL CLOCK AT 16X SAMPLING Required Output Data Rate 400 2400 4800 9600 10000 19200 25000 28800 38400 50000 57600 75000 100000 115200 153600 200000 225000 230400 250000 300000 DIVISOR FOR 16x Clock (Decimal) 3750 625 312.5 156.25 150 78.125 60 52.0833 39.0625 30 26.0417 20 15 13.0208 9.7656 7.5 6.6667 6.5104 6 5 DIVISOR OBTAINABLE IN 698 3750 625 312 8/16 156 4/16 150 78 2/16 60 52 1/16 39 1/16 30 26 1/16 20 15 13 9 12/16 7 8/16 6 11/16 6 8/16 6 5 DLM PROGRAM VALUE (HEX) E 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 DLL PROGRAM VALUE (HEX) A6 71 38 9C 96 4E 3C 34 27 1E 1A 14 F D 9 7 6 6 6 5 DLD PROGRAM VALUE (HEX)) 0 0 8 4 0 2 0 1 1 0 1 0 0 0 C 8 B 8 0 0 DATA ERROR RATE (%) 0 0 0 0 0 0 0 0.04 0 0 0.08 0 0 0.16 0.16 0 0.31 0.16 0 0 10 XR16V698 REV. 1.0.3 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO TABLE 4: TYPICAL DATA RATES WITH A 24 MHZ CRYSTAL OR EXTERNAL CLOCK AT 16X SAMPLING Required Output Data Rate 400000 460800 500000 750000 921600 1000000 DIVISOR FOR 16x Clock (Decimal) 3.75 3.2552 3 2 1.6276 1.5 DIVISOR OBTAINABLE IN 698 3 12/16 3 4/16 3 2 1 10/16 1 8/16 DLM PROGRAM VALUE (HEX) 0 0 0 0 0 0 DLL PROGRAM VALUE (HEX) 3 3 3 2 1 1 DLD PROGRAM VALUE (HEX)) C 4 0 0 A 8 DATA ERROR RATE (%) 0 0.16 0 0 0.16 0 2.7 Transmitter The transmitter section comprises of an 8-bit Transmit Shift Register (TSR) and 32 bytes of FIFO which includes a byte-wide Transmit Holding Register (THR). TSR shifts out every data bit with the 16X or 8X or 4X (if 8X or 4X sampling is selected via the 8XMODE Register or 4XMODE Register) internal clock. A bit time is 16 (or 8 or 4) clock periods. The transmitter sends the start-bit followed by the number of data bits, inserts the proper parity-bit if enabled, and adds the stop-bit(s). The status of the FIFO and TSR are reported in the Line Status Register (LSR bit-5 and bit-6). 2.7.1 Transmit Holding Register (THR) - Write Only The transmit holding register is an 8-bit register providing a data interface to the host processor. The host writes transmit data byte to the THR to be converted into a serial data stream including start-bit, data bits, parity-bit and stop-bit(s). The least-significant-bit (Bit-0) becomes first data bit to go out. The THR is the input register to the transmit FIFO of 32 bytes when FIFO operation is enabled by FCR bit-0. Every time a write operation is made to the THR, the FIFO data pointer is automatically bumped to the next sequential data location. 2.7.2 Transmitter Operation in non-FIFO Mode The host loads transmit data to THR one character at a time. The THR empty flag (LSR bit-5) is set when the data byte is transferred to TSR. THR flag can generate a transmit empty interrupt (ISR bit-1) when it is enabled by IER bit-1. The TSR flag (LSR bit-6) is set when TSR becomes completely empty. FIGURE 5. TRANSMITTER OPERATION IN NON-FIFO MODE Data Byte Transmit Holding Register (THR) THR Interrupt (ISR bit-1) Enabled by IER bit-1 16X or 8X or 4X Clock Transmit Shift Register (TSR) M S B L S B TXNOFIFO1 11 XR16V698 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO 2.7.3 Transmitter Operation in FIFO Mode REV. 1.0.3 The host may fill the transmit FIFO with up to 32 bytes of transmit data. The THR empty flag (LSR bit-5) is set whenever the FIFO is empty. The THR empty flag can generate a transmit empty interrupt (ISR bit-1) when the amount of data in the FIFO falls below its programmed trigger level. The transmit empty interrupt is enabled by IER bit-1. The TSR flag (LSR bit-6) is set when TSR/FIFO becomes empty. FIGURE 6. TRANSMITTER OPERATION IN FIFO AND FLOW CONTROL MODE Transmit Data Byte Transmit FIFO THR Interrupt (ISR bit-1) falls below the programmed Trigger Level and then when becomes empty. FIFO is Enabled by FCR bit-0=1 Auto CTS Flow Control (CTS# pin) Flow Control Characters (Xoff1/2 and Xon1/2 Reg.) Auto Software Flow Control 16X or 8X or 4X Clock Transmit Data Shift Register (TSR) 2.8 Receiver The receiver section contains an 8-bit Receive Shift Register (RSR) and 32 bytes of FIFO which includes a byte-wide Receive Holding Register (RHR). The RSR uses the 16X (or the 8X or the 4X) clock for timing. It verifies and validates every bit on the incoming character in the middle of each data bit. On the falling edge of a start or false start bit, an internal receiver counter starts counting the number of 16X (or 8X or 4X) clocks. After 8 (or 4 or 2) clocks the start bit period should be at the center of the start bit. At this time the start bit is sampled and if it is still a logic 0 it is validated. Evaluating the start bit in this manner prevents the receiver from assembling a false character. The rest of the data bits and stop bits are sampled and validated in this same manner to prevent false framing. If there were any error(s), they are reported in the LSR register bits 2-4. Upon unloading the receive data byte from RHR, the receive FIFO pointer is bumped and the error tags are immediately updated to reflect the status of the data byte in RHR register. RHR can generate a receive data ready interrupt upon receiving a character or delay until it reaches the FIFO trigger level. Furthermore, data delivery to the host is guaranteed by a receive data ready time-out interrupt when data is not received for 4 word lengths as defined by LCR[1:0] plus 12 bits time. This is equivalent to 3.7-4.6 character times. The RHR interrupt is enabled by IER bit-0. 2.8.1 Receive Holding Register (RHR) - Read-Only The Receive Holding Register is an 8-bit register that holds a receive data byte from the Receive Shift Register. It provides the receive data interface to the host processor. The RHR register is part of the receive FIFO of 32 bytes by 11-bits wide, the 3 extra bits are for the 3 error tags to be reported in LSR register. When the FIFO is enabled by FCR bit-0, the RHR contains the first data character received by the FIFO. After the RHR is read, the next character byte is loaded into the RHR and the errors associated with the current data byte are immediately updated in the LSR bits 2-4. 12 XR16V698 REV. 1.0.3 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO FIGURE 7. RECEIVER OPERATION IN NON-FIFO MODE 16X or 8X or 4X Clock R eceive Data Shift Register (RSR) Data Bit Validation Receive Data Characters Receive Data Byte and Errors Error Tags in LSR bits 4:2 Receive Data Holding Register (RHR) RHR Interrupt (ISR bit-2) RXFIFO1 FIGURE 8. RECEIVER OPERATION IN FIFO AND AUTO RTS FLOW CONTROL MODE 16X or 8X or 4X Clock Receive Data Shift Register (RSR) Data Bit Validation Example: 32 bytes by 11-bit wide FIFO Error Tags (64-sets) Receive Data Characters - RX FIFO trigger level selected at 16 bytes (See Note Below) Data falls to 8 Receive Data FIFO RTS# re-asserts when data falls below the flow control trigger level to restart remote transmitter. Enable by EFR bit-6=1, MCR bit-1. RHR Interrupt (ISR bit-2) programmed for desired FIFO trigger level. FIFO is Enabled by FCR bit-0=1 RTS# de-asserts when data fills above the flow control trigger level to suspend remote transmitter. Enable by EFR bit-6=1, MCR bit-1. FIFO Trigger=16 Data fills to 24 Error Tags in LSR bits 4:2 Receive Data Byte and Errors Receive Data RXFIFO1 2.9 THR and RHR Register Locations The THR and RHR register addresses for channel 0 to channel 7 are shown in Table 5 below. The THR and RHR for channels 0 to 7 are located at address 0x00, 0x10, 0x20, 0x30, 0x40, 0x50, 0x60 and 0x70 respectively. Transmit data byte is loaded to the THR when writing to that address and receive data is unloaded from the RHR register when reading that address. Both THR and RHR registers are 16C550 compatible in 8-bit format, so each bus operation can only write or read in bytes. 13 XR16V698 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO REV. 1.0.3 . TABLE 5: TRANSMIT AND RECEIVE HOLDING REGISTER LOCATIONS, 16C550 COMPATIBLE THR and RHR Address Locations For CH0 to CH7 (16C550 Compatible) CH0 0x00 Write THR CH0 0x00 Read RHR CH1 0x10 Write THR CH1 0x10 Read RHR CH2 0x20 Write THR CH2 0x20 Read RHR CH3 0x30 Write THR CH3 0x30 Read RHR CH4 0x40 Write THR CH4 0x40 Read RHR CH5 0x50 Write THR CH5 0x50 Read RHR CH6 0x60 Write THR CH6 0x60 Read RHR CH7 0x70 Write THR CH7 0x70 Read RHR Bit-7 Bit-7 Bit-7 Bit-7 Bit-7 Bit-7 Bit-7 Bit-7 Bit-7 Bit-7 Bit-7 Bit-7 Bit-7 Bit-7 Bit-7 Bit-7 Bit-6 Bit-6 Bit-6 Bit-6 Bit-6 Bit-6 Bit-6 Bit-6 Bit-6 Bit-6 Bit-6 Bit-6 Bit-6 Bit-6 Bit-6 Bit-6 Bit-5 Bit-5 Bit-5 Bit-5 Bit-5 Bit-5 Bit-5 Bit-5 Bit-5 Bit-5 Bit-5 Bit-5 Bit-5 Bit-5 Bit-5 Bit-5 Bit-4 Bit-4 Bit-4 Bit-4 Bit-4 Bit-4 Bit-4 Bit-4 Bit-4 Bit-4 Bit-4 Bit-4 Bit-4 Bit-4 Bit-4 Bit-4 Bit-3 Bit-3 Bit-3 Bit-3 Bit-3 Bit-3 Bit-3 Bit-3 Bit-3 Bit-3 Bit-3 Bit-3 Bit-3 Bit-3 Bit-3 Bit-3 Bit-2 Bit-2 Bit-2 Bit-2 Bit-2 Bit-2 Bit-2 Bit-2 Bit-2 Bit-2 Bit-2 Bit-2 Bit-2 Bit-2 Bit-2 Bit-2 Bit-1 Bit-1 Bit-1 Bit-1 Bit-1 Bit-1 Bit-1 Bit-1 Bit-1 Bit-1 Bit-1 Bit-1 Bit-1 Bit-1 Bit-1 Bit-1 Bit-0 Bit-0 Bit-0 Bit-0 Bit-0 Bit-0 Bit-0 Bit-0 Bit-0 Bit-0 Bit-0 Bit-0 Bit-0 Bit-0 Bit-0 Bit-0 THRRHR1 2.10 Auto RTS/DTR Hardware Flow Control Operation Automatic RTS/DTR flow control is used to prevent data overrun to the local receiver FIFO. The RTS#/DTR# output pin is used to request remote unit to suspend/resume data transmission. The flow control features are individually selected to fit specific application requirement (see Figure 9): • Select RTS (and CTS) or DTR (and DSR) through MCR bit-2. • Enable auto RTS/DTR flow control using EFR bit-6. • The auto RTS or auto DTR function must be started by asserting the RTS# or DTR# output pin (MCR bit-1 or bit-0 to a logic 1, respectively) after it is enabled. With the Auto RTS function enabled, the RTS# output pin will not be de-asserted (HIGH) when the receive FIFO reaches the programmed trigger level, but will be de-asserted when the FIFO reaches the next trigger level (See Table 14). The RTS# output pin will be asserted (LOW) again after the FIFO is unloaded to the next trigger level below the programmed trigger level. However, even under these conditions, the 698 will continue to accept data until the receive FIFO is full if the remote UART transmitter continues to send data. • If used, enable RTS/DTR interrupt through IER bit-6 (after setting EFR bit-4). The UART issues an interrupt when the RTS#/DTR# pin makes a transition: ISR bit-5 will be set to 1. 14 XR16V698 REV. 1.0.3 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO Auto CTS/DSR Flow Control 2.10.1 Automatic CTS/DSR flow control is used to prevent data overrun to the remote receiver FIFO. The CTS/DSR pin is monitored to suspend/restart local transmitter. The flow control features are individually selected to fit specific application requirement (see Figure 9): • Select CTS (and RTS) or DSR (and DTR) through MCR bit-2. • Enable auto CTS/DSR flow control using EFR bit-7. With the Auto CTS or Auto DTR function enabled, the UART will suspend transmission as soon as the stop bit of the character in the Transmit Shift Register has been shifted out. Transmission is resumed after the CTS#/ DTR# input is re-asserted (LOW), indicating more data may be sent. • If used, enable CTS/DSR interrupt through IER bit-7 (after setting EFR bit-4). The UART issues an interrupt when the CTS#/DSR# pin makes a transition: ISR bit-5 will be set to a logic 1, and UART will suspend TX transmissions as soon as the stop bit of the character in process is shifted out. Transmission is resumed after the CTS#/DSR# input returns LOW, indicating more data may be sent. 15 XR16V698 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO FIGURE 9. AUTO RTS/DTR AND CTS/DSR FLOW CONTROL OPERATION Local UART UARTA Receiver FIFO Trigger Reached Auto RTS Trigger Level Transmitter Auto CTS Monitor RXA TXB Remote UART UARTB Transmitter Auto CTS Monitor Receiver FIFO Trigger Reached Auto RTS Trigger Level REV. 1.0.3 RTSA# TXA CTSB# RXB CTSA# Assert RTS# to Begin Transmission 1 ON 2 7 ON 3 8 OFF RTSB# RTSA# CTSB# TXB OFF 10 11 ON ON Data Starts 4 RXA FIFO INTA (RXA FIFO Interrupt) Receive RX FIFO Data Trigger Level 5 6 Suspend Restart 9 RTS High Threshold RTS Low Threshold 12 RX FIFO Trigger Level RTSCTS1 The local UART (UARTA) starts data transfer by asserting RTSA# (1). RTSA# is normally connected to CTSB# (2) of remote UART (UARTB). CTSB# allows its transmitter to send data (3). TXB data arrives and fills UARTA receive FIFO (4). When RXA data fills up to its receive FIFO trigger level, UARTA activates its RXA data ready interrupt (5) and continues to receive and put data into its FIFO. If interrupt service latency is long and data is not being unloaded, UARTA monitors its receive data fill level to match the upper threshold of RTS delay and de-assert RTSA# (6). CTSB# follows (7) and request UARTB transmitter to suspend data transfer. UARTB stops or finishes sending the data bits in its transmit shift register (8). When receive FIFO data in UARTA is unloaded to match the lower threshold of RTS delay (9), UARTA re-asserts RTSA# (10), CTSB# recognizes the change (11) and restarts its transmitter and data flow again until next receive FIFO trigger (12). This same event applies to the reverse direction when UARTA sends data to UARTB with RTSB# and CTSA# controlling the data flow. 16 XR16V698 REV. 1.0.3 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO 2.11 Auto Xon/Xoff (Software) Flow Control When software flow control is enabled (See Table 17), the 698 compares one or two sequential receive data characters with the programmed Xon-1,2 or Xoff-1,2 character value(s). If receive character(s) (RX) match the programmed Xoff-1,2 value(s), the 698 will halt transmission (TX) as soon as the current character has completed transmission. When a match occurs, the Xoff (if enabled via IER bit-5) flag will be set and the interrupt output pin will be activated. Following a suspension due to a match of the Xoff character(s), the 698 will monitor the receive data stream for a match to the Xon-1,2 character(s). If a match is found, the 698 will resume operation and clear the flags (ISR bit-4). Reset initially sets the contents of the Xon1, Xon2, Xoff1 and Xoff2 flow control registers to ’0’. Following reset, any desired Xon/Xoff value can be used for software flow control. Different conditions can be set to detect Xon/ Xoff characters (See Table 17) and suspend/resume transmissions. When double 8-bit Xon/Xoff characters are selected, the 698 compares two consecutive receive characters with two software flow control 8-bit values (Xon1, Xon2, Xoff1, Xoff2) and controls TX transmissions accordingly. Under the above described flow control mechanisms, flow control characters are not placed (stacked) in the user accessible RX data buffer or FIFO. In the event that the receive buffer is overfilling and flow control needs to be executed, the 698 automatically sends an Xoff message (when enabled) via the serial TX output to the remote modem. The 698 sends the Xoff1,2 characters two character times (= time taken to send two characters at the programmed baud rate) after the receive FIFO crosses the programmed trigger level. To clear this condition, the 698 will transmit the programmed Xon-1,2 characters as soon as receive FIFO is less than one trigger level below the programmed trigger level. Table 6 below explains this. TABLE 6: AUTO XON/XOFF (SOFTWARE) FLOW CONTROL RX TRIGGER LEVEL 8 16 24 28 INT PIN ACTIVATION 8 16 24 28 XOFF CHARACTER(S) SENT (CHARACTERS IN RX FIFO) 8* 16* 24* 28* XON CHARACTER(S) SENT (CHARACTERS IN RX FIFO) 0 8 16 24 * After the trigger level is reached, an xoff character is sent after a short span of time (= time required to send 2 characters); for example, after 2.083ms has elapsed for 9600 baud and 10-bit word length setting. 2.12 Special Character Detect A special character detect feature is provided to detect an 8-bit character when bit-5 is set in the Enhanced Feature Register (EFR). When this character (Xoff2) is detected, it will be placed in the FIFO along with normal incoming RX data. The 698 compares each incoming receive character with Xoff-2 data. If a match exists, the received data will be transferred to FIFO and ISR bit-4 will be set to indicate detection of special character. Although the Internal Register Table shows Xon, Xoff Registers with 8 bits of character information, the actual number of bits is dependent on the programmed word length. Line Control Register (LCR) bits 0-1 defines the number of character bits, i.e., either 5 bits, 6 bits, 7 bits, or 8 bits. The word length selected by LCR bits 0-1 also determines the number of bits that will be used for the special character comparison. Bit-0 in the Xon, Xoff Registers corresponds to the LSB bit for the receive character. 17 XR16V698 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO 2.13 Auto RS-485 Half-duplex Control REV. 1.0.3 The auto RS-485 half-duplex direction control changes the behavior of the transmitter when enabled by FCTR bit-5. It also changes the behavior of the transmit empty interrupt (see Table 2). It asserts RTS# or DTR# (LOW) after a specified delay indicated in MSR[7:4] following the last stop bit of the last character that has been transmitted. This helps in turning around the transceiver to receive the remote station’s response. The delay optimizes the time needed for the last transmission to reach the farthest station on a long cable network before switching off the line driver. This delay prevents undesirable line signal disturbance that causes signal degradation. When the host is ready to transmit next polling data packet again, it only has to load data bytes to the transmit FIFO. The transmitter automatically de-asserts RTS# or DTR# output (HIGH) prior to sending the data. The auto RS-485 half-duplex direction control also changes the transmitter empty interrupt to TSR empty instead of THR empty. 2.13.1 Normal Multidrop Mode Normal multidrop mode is enabled when MSR bit-0 = 1 and EFR bit-5 = 0 (Special Character Detect disabled). The receiver is set to Force Parity 0 (LCR[5:3] = ’111’) in order to detect address bytes. With the receiver initially disabled, it ignores all the data bytes (parity bit = 0) until an address byte is received (parity bit = 1). This address byte will cause the UART to set the parity error. The UART will generate an LSR interrupt and place the address byte in the RX FIFO. The software then examines the byte and enables the receiver if the address matches its slave address, otherwise, it does not enable the receiver. If the receiver has been enabled, the receiver will receive the subsequent data. If an address byte is received, it will generate an LSR interrupt. The software again examines the byte and if the address matches its slave address, it does not have to anything. If the address does not match its slave address, then the receiver should be disabled. 2.13.2 Auto Address Detection Auto address detection mode is enabled when MSR bit-0 = 1 and EFR bit-5 = 1. The desired slave address will need to be written into the XOFF2 register. The receiver will try to detect an address byte that matches the porgrammed character in the XOFF2 register. If the received byte is a data byte or an address byte that does not match the programmed character in the XOFF2 register, the receiver will discard these data. Upon receiving an address byte that matches the XOFF2 character, the receiver will be automatically enabled if not already enabled, and the address character is pushed into the RX FIFO along with the parity bit (in place of the parity error bit). The receiver also generates an LSR interrupt. The receiver will then receive the subsequent data. If another address byte is received and this address does not match the programmed XOFF2 character, then the receiver will automatically be disabled and the address byte is ignored. If the address byte matches XOFF2, the receiver will put this byte in the RX FIFO along with the parity bit in the parity error bit. 18 XR16V698 REV. 1.0.3 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO 2.14 Infrared Mode Each UART in the 698 includes the infrared encoder and decoder compatible to the IrDA (Infrared Data Association) version 1.0. The input pin ENIR conveniently activates all 8 UART channels to start up in the infrared mode. Note that the ENIR pin is sampled when the RST# input is de-asserted. This global control pin enables the MCR bit-6 function in every UART channel register. After power up or a reset, the software can overwrite MCR bit-6 if so desired. ENIR and MCR bit-6 also disable the receiver while the transmitter is sending data. This prevents echoed data from reaching the receiver. The global activation ENIR pin prevents the infrared emitter from turning on and drawing large amount of current while the system is starting up. When the infrared feature is enabled, the transmit data outputs, TX[7:0], would idle at logic zero level. Likewise, the RX [7:0] inputs assume an idle level of logic zero. The infrared encoder sends out a 3/16 of a bit wide HIGH-pulse for each “0” bit in the transmit data stream. This signal encoding reduces the on-time of the infrared LED, hence reduces the power consumption. See Figure 10 below. The infrared decoder receives the input pulse from the infrared sensing diode on RX pin. Each time it senses a light pulse, it returns a logic zero to the data bit stream. The decoder also accepts (when FCTR bit-4 = 1) an inverted IR-encoded input signal. This option supports active LOW instead of normal active HIGH pulse from some infrared modules on the market. FIGURE 10. INFRARED TRANSMIT DATA ENCODING AND RECEIVE DATA DECODING Character Start Data Bits 1 0 1 0 0 1 1 0 Stop 1 1/2 Bit Time 3/16 Bit Time IrEncoder-1 TX Data 0 Transmit IR Pulse (TX Pin) Bit Time Receive IR Pulse (RX pin) Bit Time 1/16 Clock Delay RX Data 0 Start 1 0 1 0 0 11 0 1 Stop IRdecoder- Data Bits Character 19 XR16V698 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO 2.15 Sleep Mode with Auto Wake-Up REV. 1.0.3 The 698 supports low voltage system designs, hence, a sleep mode is included to reduce its power consumption when the chip is not actively used. All of these conditions must be satisfied for the 698 to enter sleep mode: ■ ■ ■ ■ no interrupts pending for all 8 channels of the 698 (ISR bit-0 = 1) SLEEP register = 0xFF modem inputs are not toggling (MSR bits 0-3 = 0) RX input pin of all 8 channels are idling HIGH The 698 stops its crystal oscillator to conserve power in the sleep mode. User can check the XTAL2 pin for no clock output as an indication that the device has entered the sleep mode. The 698 resumes normal operation by any of the following: ■ ■ ■ a receive data start bit transition (HIGH to LOW) a data byte is loaded to the transmitter, THR or FIFO a change of logic state on any of the modem or general purpose serial inputs: CTS#, DSR#, CD#, RI# If the 698 is awakened by any one of the above conditions, it will generate an interrupt. If the interrupt for the event that woke up the 698 is not enabled, then a special wake-up interrupt occurs where reading the interrupt status register will return a "no interrupt" indication. For example, there is a change of state on the CTS# input that wakes up the 698, but the MSR interrupt is not enabled. Reading the interrupt status register will return a value indicating that there are no pending interrupts and will clear the wake-up interrupt. The 698 will return to the sleep mode automatically after all interrupting conditions have been serviced and cleared. If the 698 is awakened by the modem inputs, a read to the MSR is required to reset the modem inputs. In any case, the sleep mode will not be entered while an interrupt is pending in any channel. The 698 will stay in the sleep mode of operation until it is disabled by setting SLEEP = 0x00. A word of caution: owing to the starting up delay of the crystal oscillator after waking up from sleep mode, the first few receive characters may be lost. The number of characters lost during the restart also depends on your operating data rate. More characters are lost when operating at higher data rate. 20 XR16V698 REV. 1.0.3 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO 2.16 Internal Loopback Each UART channel provides an internal loopback capability for system diagnostic purposes. The internal loopback mode is enabled by setting MCR register bit-4 to logic 1. All regular UART functions operate normally. Figure 11 shows how the modem port signals are re-configured. Transmit data from the transmit shift register output is internally routed to the receive shift register input allowing the system to receive the same data that it was sending. The TX pin is held at HIGH or mark condition while RTS# and DTR# are de-asserted (HIGH), and CTS#, DSR# CD# and RI# inputs are ignored. FIGURE 11. INTERNAL LOOP BACK VCC Transmit Shift Register MCR bit-4=1 TX [7:0] Internal Bus Lines and Control Signals Receive Shift Register VCC RX [7:0] RTS# [7:0] RTS# Modem / General Purpose Control Logic CTS# CTS# [7:0] VCC DTR# DTR# [7:0] DSR# OP1# RI# OP2# CD# DSR# [7:0] RI# [7:0] CD# [7:0] 21 XR16V698 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO 3.0 XR16V698 REGISTERS REV. 1.0.3 The XR16V698 octal UART register set consists of the Device Configuration Registers that are accessible directly from the data bus for programming general operating conditions of the UARTs and monitoring the status of various functions. These functions include all 8 channel UART’s interrupt control and status, 16-bit general purpose timer control and status, sleep mode, soft-reset, and device identification and revision. Also, each UART channel has its own set of internal UART Configuration Registers for its own operation control, status reporting and data transfer. These registers are mapped into a 256-byte of the data memory address space. The following paragraphs describe all the registers in detail. FIGURE 12. THE XR16V698 REGISTERS 0x00-0F Channel 0 0x10-1F Channel 1 0x20-2F Channel 2 0x30-3F Channel 3 8-bit Data Bus Interface 0x40-4F Channel 4 0x50-5F Channel 5 0x60-6F Channel 6 0x70-7F Channel 7 INT0, INT1, INT2, INT3, TIMER, SLEEP, RESET 0x80-8F Device Configuration Registers 8 channel Interrupts, 16-bit Timer/Counter, Sleep, Reset, DVID, DREV 698REGS-1 UART[7:0] Configuration Registers 16550 Compatible and EXAR Enhanced Registers 22 XR16V698 REV. 1.0.3 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO 3.1 DEVICE CONFIGURATION REGISTER SET The device configuration registers are directly accessible from the bus. This provides easy programming of general operating parameters to the 698 UART and for monitoring the status of various functions. The device configuration registers are mapped onto address 0x80-8F as shown on the register map in Table 8 and Figure 12. These registers provide global controls and status of all 8 channel UARTs that include interrupt status, 16-bit general purpose timer control and status, 4X or 8X or 16X sampling clock, sleep mode control, soft-reset control, simultaneous UART initialization, and device identification and revision. TABLE 7: XR16V698 REGISTER SETS ADDRESS [A7:A0] 0x00 - 0x0F 0x10 - 0x1F 0x20 - 0x2F 0x30 - 0x3F 0x40 - 0x4F 0x50 - 0x5F 0x60 - 0x6F 0x70 - 0x7F 0x80 - 0x8F UART CHANNEL SPACE UART channel 0 Registers UART channel 1 Registers UART channel 2 Registers UART channel 3 Registers UART channel 4 Registers UART channel 5 Registers UART channel 6 Registers UART channel 7 Registers Device Configuration Registers REFERENCE (Table 11 & 12) (Table 11 & 12) (Table 11 & 12) (Table 11 & 12) (Table 11 & 12) (Table 11 & 12) (Table 11 & 12) (Table 11 & 12) (Table 8) Interrupt registers and global controls First 8 registers are 16550 compatible COMMENT 23 XR16V698 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO REV. 1.0.3 TABLE 8: DEVICE CONFIGURATION REGISTERS ADDRESS READ/ [A7:A0] WRITE 0x80 0x81 R R REGISTER INT Source INT 1 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 UART 7 UART 2 bit 1 UART 5 bit 0 UART 7 bit 2 0 0 bit 7 bit 7 UART 7 UART 7 Reset UART 7 Enable sleep UART 7 bit 7 0 0 UART 6 source bit 0 UART 4 bit 2 interrupt bit 1 0 0 bit 6 bit 6 UART 6 UART 6 Reset UART 6 Enable sleep UART 6 bit 6 1 0 UART 5 UART 1 bit 2 interrupt bit 1 source bit 0 0 0 bit 5 bit 5 UART 5 UART 5 Reset UART 5 Enable sleep UART 5 bit 5 1 0 UART 4 interrupt bit 1 source bit 0 UART 6 bit 2 0 0 bit 4 bit 4 UART 4 UART 4 Reset UART 4 Enable sleep UART 4 bit 4 0 0 UART 3 source bit 0 UART 3 bit 2 interrupt bit 1 UART 2 UART 0 bit 2 interrupt bit 1 source bit 0 UART 1 interrupt bit 1 source bit 0 UART 5 bit 2 UART 0 source bit 0 UART 2 bit 2 source bit 1 0x82 R INT 2 0x83 R INT 3 0x84 0x85 0x86 0x87 0x88 0x89 0x8A 0x8B R/W R TIMER CTRL TIMER TimerCtrl TimerCtrl TimerCtrl TimerCtrl bit-3 bit-2 bit-1 bit-0 0 bit 3 bit 3 UART 3 UART 3 Reset UART 3 Enable sleep UART 3 bit 3 1 0 0 bit 2 bit 2 UART 2 UART 2 Reset UART 2 Enable sleep UART 2 bit 2 0 0 0 bit 1 bit 1 UART 1 UART 1 Reset UART 1 Enable sleep UART 1 bit 1 0 0 0 bit 0 bit 0 UART 0 UART 0 Reset UART 0 Enable sleep UART 0 bit 0 0 write to all UARTs R/W TIMER LSB R/W R/W R/W W R/W TIMER MSB 8X MODE 4X MODE RESET SLEEP 0x8C 0x8D 0x8E R R R/W DREV DVID REGB 3.1.1 The Global Interrupt Source Registers The XR16V698 has a global interrupt source register set that consists of 4 consecutive registers [INT0, INT1, INT2 and INT3]. The four registers are in the device configuration register address space. INT3 [0x00] INT2 [0x00] INT1 [0x00] INT0 [0x00] All four registers default to logic zero (as indicated in square braces) for no interrupt pending. All 8 channel interrupts are enabled or disabled in each channel’s IER register. INT0 shows individual status for each channel while INT1, INT2 and INT3 show the details of the source of each channel’s interrupt with its unique 3bit encoding. Figure 13 shows the 4 interrupt registers in sequence for clarity. The 16-bit timer and sleep wake-up interrupts are masked in the device configuration registers, TIMERCNTL and SLEEP. An interrupt is generated (if enabled) by the 698 when awakened from sleep if all 8 channels were placed in the sleep mode previously. 24 XR16V698 REV. 1.0.3 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO Each bit gives an indication of the channel that has requested for service. For example, bit-0 represents channel 0 and bit-7 indicates channel 7. Logic one indicates the channel N [7:0] has called for service. The interrupt bit clears after reading the appropriate register of the interrupting UART channel register (ISR, LSR and MSR). SEE”INTERRUPT CLEARING:” ON PAGE 34. for interrupt clearing details. 3.1.1.1 INT0 Channel Interrupt Indicator INT0 Register Individual UART Channel Interrupt Status Bit-7 Ch-7 Bit-6 Ch-6 Bit-5 Ch-5 Bit-4 Ch-4 Bit-3 Ch-3 Bit-2 Ch-2 Bit-1 Ch-1 Bit-0 Ch-0 3.1.1.2 INT1, INT2 and INT3 Interrupt Source Locator INT3, INT2 and INT1 provide a 24-bit (3 bits per channel) encoded interrupt indicator. Table 9 shows the 3 bit encoding and their priority order. The 16-bit Timer time-out interrupt will show up only as a channel 0 interrupt. For other channels, interrupt 7 is reserved. . FIGURE 13. THE GLOBAL INTERRUPT REGISTERS, INT0, INT1, INT2 AND INT3 Interrupt Registers, INT0, INT1, INT2 and INT3 INT3 Register Channel-7 Bit 2 Bit 1 Bit 0 Bit 2 Channel-6 Bit 1 Bit 0 Bit 2 Channel-5 Bit 1 Bit 0 Bit 2 INT2 Register Channel-4 Bit 1 Bit 0 Bit 2 Channel-3 Bit 1 Bit 0 Bit 2 Channel-2 Bit 1 Bit 0 Bit 2 INT1 Register Channel-1 Bit 1 Bit 0 Bit 2 Channel-0 Bit 1 Bit 0 INT0 Register Ch-7 Ch-6 Ch-5 Ch-4 Ch-3 Ch-2 Ch-1 Ch-0 Bit-7 Bit-6 Bit-5 Bit-4 Bit-3 Bit-2 Bit-1 Bit-0 25 XR16V698 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO TABLE 9: UART CHANNEL [7:0] INTERRUPT SOURCE ENCODING AND CLEARING PRIORITY x 1 2 3 4 Bit Bit Bit 2 1 0 0 0 0 0 1 0 0 1 1 0 0 1 0 1 0 None or wake-up indicator RXRDY & RX Line Status (logic OR of LSR[4:1]). RXRDY INT clears by reading data in the RX FIFO until it falls below the trigger level; RX Line Status INT cleared after reading LSR register. RXRDY Time-out: Cleared same way as RXRDY INT. TXRDY, THR or TSR (auto RS-485 mode) empty, clears after reading ISR register. MSR, RTS/CTS or DTR/DSR delta or Xoff/Xon or special character detected. The first two clears after reading MSR register; Xoff/Xon or special char. detect INT clears after reading ISR register. Reserved. Reserved. TIMER Time-out, shows up as a channel 0 INT. It clears after reading the TIMERCNTL register. Reserved in other channels. INTERRUPT SOURCE(S) AND CLEARING REV. 1.0.3 5 6 7 1 1 1 0 1 1 1 0 1 3.1.2 General Purpose 16-bit Timer/Counter [TIMERMSB, TIMELSB, TIMER, TIMECNTL] (DEFAULT 0XXX-XX-00-00) The 698 includes a 16-bit general purpose timer/counter. Its clock source may be selected from internal crystal oscillator or externally on pin TMRCK. The timer can be set to be a single-shot for a one-time event or retriggerable for a periodic signal. An interrupt may be generated when the timer times out and will show up as a Channel 0 interrupt (see Table 9). It is controlled through 4 configuration registers [TIMERCNTL, TIMER, TIMELSB, TIMERMSB]. These registers provide start/stop and re-triggerable or one-shot operation (see Table 10 below). The time-out output of the Timer can be set to generate an interrupt for system or event alarm. 3.1.2.1 TIMERMSB [7:0] and TIMERLSB [7:0] TIMERMSB and TIMERLSB form a 16-bit value. The least-significant bit of the timer is being bit-0 of the TIMERLSB with most-significant-bit being bit-7 in TIMERMSB. Notice that these registers do not hold the current counter value when read. Default value is zero (timer disabled) upon powerup and reset. 16-Bit Timer/Counter Programmable Registers TIMERMSB Register Bit-15 Bit-14 Bit-13 Bit-12 Bit-11 Bit-10 Bit-9 Bit-8 Bit-7 Bit-6 TIMERLSB Register Bit-5 Bit-4 Bit-3 Bit-2 Bit-1 Bit-0 3.1.2.2 3.1.2.3 TIMER [7:0] Reserved TIMERCNTL [7:0] Register The bits 3:0 of this register are used to issue commands. The commands are self-clearing, so reading this register does not show the last written command. Reading this register returns a value of 0x01 when there is a Timer interrupt pending and 0x00 at all other times. 26 XR16V698 REV. 1.0.3 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO TABLE 10: TIMER CONTROL COMMANDS TIMERCNTL [7:4] TIMERCNTL [3:0] Reserved These bits are used to invoke a series of commands that control the function of the Timer/Counter. The commands 1011 to 1111 are reserved. 0001: Enable Timer Interrupt 0010: Disable Timer Interrupt (default) 0011: Select One-shot mode 0100: Select Re-triggerable mode (default) 0101: Select Internal Crystal Oscillator output as clock source for the Timer (default) 0110: Select External Clock source (through TMRCK pin) for the Timer 0111: Reserved 1000: Reserved 1001: Start Timer 1010: Stop Timer (default) 1011: Reset Timer Upon power-up or reset, the default states are Timer interrupt disabled, Re-triggerable mode, Crystal Oscillator as Timer clock source, and Timer stopped. TIMER OPERATION The following paragraphs describe the operation of the 16-bit Timer/Counter. The following conventions will be used in this discussion: ■ ■ ’N’ is the 16-bit value programmed in the TIMER MSB, LSB registers ‘N’ can take any value from 0x0002 to 0xFFFF. Timer Interrupt In the one-shot mode, the Timer will issue an interrupt ’N’ clocks after the Timer is started. This is the time when the Timer times-out in the one-shot mode. In the re-triggerable mode, the Timer will keep issuing an interrupt every ’N’ clocks. This is shown in Figure 15, where the time between successive time-outs (in retriggereble mode) is ’N’ clocks. The Timer interrupt can be cleared by reading the TIMERCNTL register. The TIMERCNTL will read a value of 0x01 when there is an interrupt and a 0x00 at all other times. FIGURE 14. TIMER/COUNTER CIRCUIT TIMERMSB and TIMERLSB (16-bit Value) Timer Interrupt TMRCK OSC. CLOCK 1 0 16-Bit Timer/Counter 1 0 Timer Interrupt No Interrupt Clock Select Start/Stop TIMERCNTL COMMANDS Single shot/Re-triggerable Timer Interrupt Enable/ Disable 27 XR16V698 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO FIGURE 15. INTERRUPT OUTPUT IN ONE-SHOT AND RE-TRIGGERABLE MODES Timer Started Timer Timed Out TIMERCNTL read REV. 1.0.3 One-shot Mode Timer Timed TIMERCNTL Out read Timer Timed Out Re-triggerable Mode 3.1.3 8XMODE [7:0] (default 0x00) Each bit selects sampling rate for that UART channel, for example, bit-0 is channel 0. This register associates with 4XMODE register to decide the sampling rate (16X or 8X or 4X). When 4XMODE [7:0] = 0x00, Logic 0 (default) selects normal 16X sampling with logic one selects 8X sampling rate. Transmit and receive data rates will double by selecting 8X. “Section 2.6, Programmable Baud Rate Generator with Fractional Divisor” on page 9 8XMODE Register Individual UART Channel 8X Clock Mode Enable Bit-7 Bit-6 Bit-5 Bit-4 Bit-3 Bit-2 Bit-1 Bit-0 Ch-7 Ch-6 Ch-5 Ch-4 Ch-3 Ch-2 Ch-1 Ch-0 3.1.4 4XMODE [7:0] (default 0x00) Each bit selects sampling rate for that UART channel, for example, bit-0 is channel 0. This register associates with 8XMODE register to decide the sampling rate (16X or 8X or 4X). When 8XMODE [7:0] = 0x00, Logic 0 (default) selects normal 16X sampling with logic 1 selects 4X sampling rate. Transmit and receive data rates will quadruple by selecting 4X. “Section 2.6, Programmable Baud Rate Generator with Fractional Divisor” on page 9 4XMODE Register Individual UART Channel 8X Clock Mode Enable Bit-7 Bit-6 Bit-5 Bit-4 Bit-3 Bit-2 Bit-1 Bit-0 Ch-7 Ch-6 Ch-5 Ch-4 Ch-3 Ch-2 Ch-1 Ch-0 28 XR16V698 REV. 1.0.3 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO RESET [7:0] (default 0x00) RESET Register Individual UART Channel Reset Enable Bit-7 Bit-6 Bit-5 Bit-4 Bit-3 Bit-2 Bit-1 Bit-0 Ch-7 Ch-6 Ch-5 Ch-4 Ch-3 Ch-2 Ch-1 Ch-0 3.1.5 The 8-bit RESET register provides the software with the ability to reset the UART(s) when there is a need. Each bit is self-resetting after it is written a logic 1 to perform a reset to that channel. All registers in that channel will be reset to the default condition, see Table 18 for details. As an example, bit-0 =1 resets UART channel 0 with bit-7=1 resets channel 7. 3.1.6 SLEEP [7:0] (default 0x00) The 8-bit Sleep register enables each UART separately to enter Sleep mode. Sleep mode reduces power consumption when the system needs to put the UART(s) to idle. The UART enters sleep mode when there is no interrupt pending. When all 8 UARTs are put to sleep, the on-chip oscillator shuts off to further conserve power. In this case, the octal UART is awaken by any of the UART channels from a receive data byte or a change on any of the modem inputs (CTS#, DSR#, CD#, RI#). The UART is ready after 32 crystal clocks to ensure full functionality. Also, a special interrupt is generated with an indication of no pending interrupt. Logic 0 (default) and logic 1 disable and enable sleep mode respectively. SLEEP Register Individual UART Channel Sleep Enable Ch-7 Ch-6 Ch-5 Ch-4 Ch-3 Ch-2 Ch-1 Ch-0 Bit-7 Bit-6 Bit-5 Bit-4 Bit-3 Bit-2 Bit-1 Bit-0 3.1.7 Device Identification and Revision There are 2 internal registers that provide device identification and revision, DVID and DREV registers. The 8bit content in the DVID register provides device identification. A return value of 0x68 from this register indicates the device is a XR16V698. The DREV register returns a 8-bit value of 0x01 for revision A, 0x02 for revision B and so on. This information is very useful to the software driver for identifying which device it is communicating with and to keep up with revision changes. 3.1.7.1 DVID [7:0] (default 0x68) Device identification for the type of UART. The Device ID for the V698 is 0x68. 3.1.7.2 DREV [7:0] (default (0x01) Revision number of the XR16V698. A 0x01 represents "revision-A" with 0x02 for rev-B and so forth. 3.1.8 REGB [7:0] (default 0x00) REGB[0]: Simultaneous write to all 8 UARTs • Logic 0 = Write to each UART configuration register individually (default). • Logic 1 = Enable simultaneous write to all 8 UART configuration registers. This can be very useful during device initialization in the power-up and reset routines. REGB[7:1]: Reserved. 29 XR16V698 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO 3.2 UART Channel Configuration Registers REV. 1.0.3 The first 8 registers are 16550 compatible with EXAR enhanced feature registers located on the upper 8 addresses. The 8 sets of UART configuration registers are decoded using address lines A0 to A3 as shown below. TABLE 11: UART CHANNEL CONFIGURATION REGISTERS ADDRESS A3 A2 A1 A0 16550 COMPATIBLE 0 0 00 RHR - Receive Holding Reg THR - Transmit Holding Register DLL - Divisor LSB DLM - Divisor MSB DLD - Divisor Fractional Part IER - Interrupt Enable Reg ISR - Interrupt Status Reg FCR - FIFO Control Reg LCR - Line Control Reg MCR - Modem Control Reg LSR - Line Status Reg MSR - Modem Status Reg - Auto RS-485 Delay SPR - Scratch Pad Reg ENHANCED REGISTER 1 1 1 1 1 0 0 0 0 1 00 01 10 11 00 FCTR EFR - Enhanced Function Reg Reserved Reserved Xoff-1 - Xoff Character 1 Xchar Xoff-2 - Xoff Character 2 Reserved Xon-1 - Xon Character 1 Reserved Xon-2 - Xon Character 2 Reserved Read/Write Read/Write Read-only Read-only Write-only Read-only Write-only Read-only Write-only Read-only Write-only Read-only Xon,Xoff Rcvd. Flags Read-only Write-only Read/Write Read/Write Read/Write Read/Write Read-only Write-only Read/Write Read/Write Read-only Read-only Write-only Read/Write LCR[7] = 0 REGISTER READ/WRITE COMMENTS 0 0 0 0 0 0 0 0 0 0 00 01 10 01 10 LCR[7] = 1 LCR[7] = 1 LCR[7] = 1 LCR[7] = 0 LCR[7] = 0 0 0 0 0 0 1 1 1 11 00 01 10 0 1 11 1 1 01 1 1 10 1 1 11 30 XR16V698 REV. 1.0.3 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO TABLE 12: UART CHANNEL CONFIGURATION REGISTERS DESCRIPTION. SHADED BITS ARE ENABLED BY EFR BIT-4. ADDRESS A3-A0 REG NAME READ/ WRITE BIT-7 BIT-6 BIT-5 BIT-4 BIT-3 BIT-2 BIT-1 BIT-0 COMMENT 0000 0000 0000 0001 0010 0001 RHR THR DLL DLM DLD IER R W R/W R/W R/W R/W Bit-7 Bit-7 Bit-7 Bit-7 0 0/ Bit-6 Bit-6 Bit-6 Bit-6 0 0/ Bit-5 Bit-5 Bit-5 Bit-5 0 0/ Bit-4 Bit-4 Bit-4 Bit-4 0 0 Bit-3 Bit-3 Bit-3 Bit-3 Bit-3 Bit-2 Bit-2 Bit-2 Bit-2 Bit-2 Bit-1 Bit-1 Bit-1 Bit-1 Bit-1 Bit-0 Bit-0 Bit-0 Bit-0 Bit-0 RX Data Int. Enable LCR[7]=0 LCR[7]=0 LCR[7]=1 LCR[7]=1 LCR[7]=1 CTS/ RTS/ Xon/Xoff/ DSR# Int. DTR# Int. Sp. Char. Enable Enable Int. Enable 0010 ISR R FIFOs Enable FIFOs Enable 0/ 0/ Modem RX Line TX Ready Status Int. Status Int. Int. Enable Enable Enable LCR[7]=0 DeltaXoff/special Flow Cntl char 0010 FCR W RX FIFO Trigger RX FIFO Trigger 0/ TX FIFO Trigger 0011 LCR R/W Divisor Enable Set TX Break 0/ TX FIFO Trigger INT Source Bit-3 DMA Mode INT Source Bit-2 TX FIFO Reset INT Source Bit-1 RX FIFO Reset INT Source Bit-0 FIFOs Enable LCR[7]=0 LCR[7]=0 Set Parity Even Parity Parity Enable Stop Bits Word Length Bit-1 Word Length Bit-0 0100 MCR R/W 0/ BRG Prescaler 0/ IR Enable 0/ XonAny Internal Loopback Enable (OP2)1 TX char Immediate (OP1)1 RTS/DTR Flow Sel RTS# Pin DTR# Pin Control Control 0101 LSR R RX FIFO TransmitERROR ter Empty CD RI TX FIFO Empty DSR RX Break RX Fram- RX Parity RX Overing Error run Error Delta CD# Disable TX Bit-3 0 Delta RI# Disable RX Bit-2 0 Delta DSR# 0 RX Data Ready Delta CTS# 9-bit Mode Bit-0 0 User Data 0110 MSR R CTS MSR W RS-485 DLY-3 Bit-7 0 RS-485 DLY-2 Bit-6 0 RS-485 DLY-1 Bit-5 Auto RS485 Enable Special Char Select RS-485 DLY-0 Bit-4 Invert IR RX Input 0111 1000 SPR FCTR R/W R/W Bit-1 0 1001 EFR R/W Auto Auto CTS/DSR RTS/DTR Enable Enable Enable IER [7:5], ISR [5:4], FCR[5:4], MCR[7:5, 3:2] MSR[7:0] 0 Software Software Software Software Flow Cntl Flow Cntl Flow Cntl Flow Cntl Bit-3 Bit-2 Bit-1 Bit-0 1010 Rsvd R 0 0 0 0 0 0 0 31 XR16V698 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO REV. 1.0.3 TABLE 12: UART CHANNEL CONFIGURATION REGISTERS DESCRIPTION. SHADED BITS ARE ENABLED BY EFR BIT-4. ADDRESS A3-A0 REG NAME READ/ WRITE BIT-7 BIT-6 BIT-5 BIT-4 BIT-3 BIT-2 BIT-1 BIT-0 COMMENT 1011 1100 Rsvd XCHAR R R 0 0 0 0 0 0 0 0 0 TX Xon Indicator Bit-3 Bit-3 Bit-3 Bit-3 0 TX Xoff Indicator Bit-2 Bit-2 Bit-2 Bit-2 0 Xon Det. Indicator Bit-1 Bit-1 Bit-1 Bit-1 0 Xoff Det. Self clear Indicator after read Bit-0 Bit-0 Bit-0 Bit-0 1100 1101 1110 1111 XOFF1 XOFF2 XON1 XON2 W W W W Bit-7 Bit-7 Bit-7 Bit-7 Bit-6 Bit-6 Bit-6 Bit-6 Bit-5 Bit-5 Bit-5 Bit-5 Bit-4 Bit-4 Bit-4 Bit-4 NOTE: MCR bits 2 and 3 (OP1 and OP2 outputs) are not available in the XR16V698. They are present for 16C550 compatibility during Internal loopback, see Figure 11. 4.0 INTERNAL REGISTER DESCRIPTIONS 4.1 Receive Holding Register (RHR) - Read Only SEE”RECEIVER” ON PAGE 12.. 4.2 Transmit Holding Register (THR) - Write Only SEE”TRANSMITTER” ON PAGE 11.. 4.3 Interrupt Enable Register (IER) - Read/Write The Interrupt Enable Register (IER) masks the interrupts from receive data ready, transmit empty, line status and modem status registers. These interrupts are reported in the Interrupt Status Register (ISR) and also encoded in INT (INT0-INT3) register in the Device Configuration Registers. 4.3.1 IER versus Receive FIFO Interrupt Mode Operation When the receive FIFO (FCR BIT-0 = a logic 1) and receive interrupts (IER BIT-0 = logic 1) are enabled, the RHR interrupts (see ISR bits 3 and 4) status will reflect the following: A. The receive data available interrupts are issued to the host when the FIFO has reached the programmed trigger level. It will be cleared when the FIFO drops below the programmed trigger level. B. FIFO level will be reflected in the ISR register when the FIFO trigger level is reached. Both the ISR register status bit and the interrupt will be cleared when the FIFO drops below the trigger level. C. The receive data ready bit (LSR BIT-0) is set as soon as a character is transferred from the shift register to the receive FIFO. It is reset when the FIFO is empty. 4.3.2 IER versus Receive/Transmit FIFO Polled Mode Operation When FCR BIT-0 equals a logic 1 for FIFO enable; resetting IER bits 3:0 enables the XR16V698 in the FIFO polled mode of operation. Since the receiver and transmitter have separate bits in the LSR either can be used in the polled mode by selecting respective transmit or receive control bit(s). A. LSR BIT-0 indicates there is data in RHR (non-FIFO mode) or RX FIFO (FIFO mode). B. LSR BIT-1 indicates an overrun error has occurred and that data in the FIFO may not be valid. C. LSR BIT 2-4 provides the type of receive data errors encountered for the data byte in RHR, if any. D. LSR BIT-5 indicates THR (non-FIFO mode) or TX FIFO (FIFO mode) is empty. E. LSR BIT-6 indicates when both the transmit FIFO and TSR are empty. F. LSR BIT-7 indicates a data error in at least one character in the RX FIFO. 32 XR16V698 REV. 1.0.3 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO IER[7]: CTS# Input Interrupt Enable (requires EFR bit-4=1) • Logic 0 = Disable the CTS# interrupt (default). • Logic 1 = Enable the CTS# interrupt. The UART issues an interrupt when CTS# pin makes a transition from LOW to HIGH. IER[6]: RTS# Output Interrupt Enable (requires EFR bit-4=1) • Logic 0 = Disable the RTS# interrupt (default). • Logic 1 = Enable the RTS# interrupt. The UART issues an interrupt when RTS# pin makes a transition from LOW to HIGH. IER[5]: Xoff Interrupt Enable (requires EFR bit-4=1) • Logic 0 = Disable the software flow control, receive Xoff interrupt (default). • Logic 1 = Enable the software flow control, receive Xoff interrupt. See Software Flow Control section for details. IER[4]: Reserved IER[3]: Modem Status Interrupt Enable The Modem Status Register interrupt is issued whenever any of the delta bits of the MSR register (bits 3:0) is set. • Logic 0 = Disable the modem status register interrupt (default). • Logic 1 = Enable the modem status register interrupt. IER[2]: Receive Line Status Interrupt Enable An Overrun error, Framing error, Parity error or detection of a Break character will result in an LSR interrupt. The 698 will issue an LSR interrupt immediately after receiving a character with an error. It will again re-issue the interrupt (if the first one has been cleared by reading the LSR register) when the character with the error is on the top of the FIFO, meaning the next one to be read out of the FIFO. For example, let’s consider an incoming data stream of 0x55, 0xAA, etc and that the character 0xAA has a Parity error associated with it. Let’s assume that the character 0x55 has not been read out of the FIFO yet. The 698 will issue an interrupt as soon as the stop bit of the character 0xAA is received. The LSR register will have only the FIFO error bit (bit-7) set and none of the other error bits (Bits 1,2,3 and 4) will be set, since the byte on the top of the FIFO is 0x55 which does not have any errors associated with it. When this byte has been read out, the 698 will issue another LSR interrupt and this time the LSR register will show the Parity bit (bit-2) set. • Logic 0 = Disable the receiver line status interrupt (default). • Logic 1 = Enable the receiver line status interrupt. IER[1]: TX Ready Interrupt Enable In non-FIFO mode, a TX interrupt is issued whenever the THR is empty. In the FIFO mode, an interrupt is issued twice: once when the number of bytes in the TX FIFO falls below the programmed trigger level and again when the TX FIFO becomes empty. When auto RS-485 mode is enabled (FCTR bit-5 = 1), the second interrupt is delayed until the transmitter (both the TX FIFO and the TX Shift Register) is empty. • Logic 0 = Disable Transmit Ready Interrupt (default). • Logic 1 = Enable Transmit Ready Interrupt. 33 XR16V698 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO IER[0]: RX Interrupt Enable REV. 1.0.3 The receive data ready interrupt will be issued when RHR has a data character in the non-FIFO mode or when the receive FIFO has reached the programmed trigger level in the FIFO mode. • Logic 0 = Disable the receive data ready interrupt (default). • Logic 1 = Enable the receiver data ready interrupt. 4.4 Interrupt Status Register (ISR) - Read Only The UART provides multiple levels of prioritized interrupts to minimize external software interaction. The Interrupt Status Register (ISR) provides the user with six interrupt status bits. Performing a read cycle on the ISR will give the user the current highest pending interrupt level to be serviced, others queue up for next service. No other interrupts are acknowledged until the pending interrupt is serviced. The Interrupt Source Table, Table 13, shows the data values (bit 0-5) for the six prioritized interrupt levels and the interrupt sources associated with each of these interrupt levels. 4.4.1 Interrupt Generation: • LSR is by any of the LSR bits 1, 2, 3 and 4. See IER bit-2 description above. • RXRDY is by RX trigger level. • RXRDY Time-out is by a 4-char plus 12 bits delay timer. • TXRDY is by TX trigger level or TX FIFO empty (or transmitter empty in auto RS-485 control). • MSR is by any of the MSR bits 0, 1, 2 and 3. • Receive Xon/Xoff/Special character is by detection of a Xon, Xoff or Special character. • CTS#/DSR# is when its transmitter toggles the input pin (from LOW to HIGH) during auto CTS/DSR flow control enabled by EFR bit-7 and selection on MCR bit-2. • RTS#/DTR# is when its receiver toggles the output pin (from LOW to HIGH) during auto RTS/DTR flow control enabled by EFR bit-6 and selection on MCR bit-2. 4.4.2 Interrupt Clearing: • LSR interrupt is cleared by a read to the LSR register. • RXRDY interrupt is cleared by reading data until FIFO falls below the trigger level. • RXRDY Time-out interrupt is cleared by reading RHR. • TXRDY interrupt is cleared by a read to the ISR register or writing to THR. • MSR interrupt is cleared by a read to the MSR register. • Xon or Xoff interrupt is cleared by a read to ISR register. • Special character interrupt is cleared by a read to ISR or after the next character is received. • RTS#/DTR# and CTS#/DSR# status change interrupts are cleared by a read to the MSR register. 34 XR16V698 REV. 1.0.3 ] 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO TABLE 13: INTERRUPT SOURCE AND PRIORITY LEVEL PRIORITY LEVEL 1 2 3 4 5 6 7 X BIT-5 0 0 0 0 0 0 1 0 ISR REGISTER STATUS BITS BIT-4 0 0 0 0 0 1 0 0 BIT-3 0 0 1 0 0 0 0 0 BIT-2 1 1 1 0 0 0 0 0 BIT-1 1 0 0 1 0 0 0 0 BIT-0 0 0 0 0 0 0 0 1 SOURCE OF THE INTERRUPT LSR (Receiver Line Status Register) RXRDY (Received Data Ready) RXRDY (Receive Data Time-out) TXRDY (Transmitter Holding Register Empty) MSR (Modem Status Register) RXRDY (Received Xon/Xoff or Special character) CTS#/DSR#, RTS#/DTR# change of state None (default) or wake-up indicator ISR[7:6]: FIFO Enable Status These bits are set to a logic 0 when the FIFOs are disabled. They are set to a logic 1 when the FIFOs are enabled. ISR[5:1]: Interrupt Status These bits indicate the source for a pending interrupt at interrupt priority levels (See Table 13). See “Section 4.4.1, Interrupt Generation:” on page 34 and “Section 4.4.2, Interrupt Clearing:” on page 34 for details. ISR[0]: Interrupt Status • Logic 0 = An interrupt is pending and the ISR contents may be used as a pointer to the appropriate interrupt service routine. • Logic 1 = No interrupt pending. (default condition) 4.5 FIFO Control Register (FCR) - Write Only This register is used to enable the FIFOs, clear the FIFOs, set the transmit/receive FIFO trigger levels, and select the DMA mode. The DMA, and FIFO modes are defined as follows: FCR[7:6]: Receive FIFO Trigger Select (logic 0 = default, RX trigger level =1) These 2 bits are used to set the trigger level for the receive FIFO. The UART will issue a receive interrupt when the number of the characters in the FIFO crosses the trigger level. Table 14 shows the complete selections. Note that the receiver and the transmitter cannot use different trigger tables. Whichever selection is made last applies to both the RX and TX side. FCR[5:4]: Transmit FIFO Trigger Select (logic 0 = default, TX trigger level = 1) These 2 bits set the trigger level for the transmit FIFO interrupt. The UART will issue a transmit interrupt when the number of characters in the FIFO falls below the selected trigger level, or when it gets empty in case that the FIFO did not get filled over the trigger level on last re-load. Table 14 below shows the selections. 35 XR16V698 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO FCR[3]: DMA Mode Select REV. 1.0.3 This bit has no effect since TXRDY and RXRDY pins are not available in this device. It is provided for legacy software compatibility. • Logic 0 = Set DMA to mode 0 (default). • Logic 1 = Set DMA to mode 1. FCR[2]: TX FIFO Reset This bit is only active when FCR bit-0 is active. • Logic 0 = No transmit FIFO reset (default). • Logic 1 = Reset the transmit FIFO pointers and FIFO level counter logic (the transmit shift register is not cleared or altered). This bit will return to a logic 0 after resetting the FIFO. FCR[1]: RX FIFO Reset This bit is only active when FCR bit-0 is active. • Logic 0 = No receive FIFO reset (default). • Logic 1 = Reset the receive FIFO pointers and FIFO level counter logic (the receive shift register is not cleared or altered). This bit will return to a logic 0 after resetting the FIFO. FCR[0]: TX and RX FIFO Enable • Logic 0 = Disable the transmit and receive FIFO (default). • Logic 1 = Enable the transmit and receive FIFOs. This bit must be set to logic 1 when other FCR bits are written or they will not be programmed. TABLE 14: TRANSMIT AND RECEIVE FIFO TRIGGER TABLE AND LEVEL SELECTION FCR BIT-7 FCR BIT-6 FCR BIT-5 0 0 1 1 0 0 1 1 0 1 0 1 FCR BIT-4 RECEIVE TRIGGER LEVEL TRANSMIT TRIGGER LEVEL 16 8 24 30 COMPATIBILITY 16C650A, 16L651 0 1 0 1 8 16 24 28 4.6 Line Control Register (LCR) - Read/Write The Line Control Register is used to specify the asynchronous data communication format. The word or character length, the number of stop bits, and the parity are selected by writing the appropriate bits in this register. LCR[7]: Baud Rate Divisors Enable Baud rate generator divisor (DLL, DLM, DLD) enable. • Logic 0 = Data registers are selected (default). • Logic 1 = Divisor latch registers (DLL, DLM and DLD) are selected. 36 XR16V698 REV. 1.0.3 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO LCR[6]: Transmit Break Enable When enabled the Break control bit causes a break condition to be transmitted (the TX output is forced to a “space’, logic 0, state). This condition remains until disabled by setting LCR bit-6 to a logic 0. • Logic 0 = No TX break condition. (default) • Logic 1 = Forces the transmitter output (TX) to a “space”, logic 0, for alerting the remote receiver of a line break condition. LCR[5]: TX and RX Parity Select If the parity bit is enabled, LCR BIT-5 selects the forced parity format. • LCR BIT-5 = logic 0, parity is not forced (default). • LCR BIT-5 = logic 1 and LCR BIT-4 = logic 0, parity bit is forced to a logical 1 for the transmit and receive data. • LCR BIT-5 = logic 1 and LCR BIT-4 = logic 1, parity bit is forced to a logical 0 for the transmit and receive data. TABLE 15: PARITY PROGRAMMING LCR BIT-5 X 0 0 1 1 LCR BIT-4 X 0 1 0 1 LCR BIT-3 0 1 1 1 1 PARITY SELECTION No parity Odd parity Even parity Force parity to mark, “1” Force parity to space, “0” LCR[4]: TX and RX Parity Select If the parity bit is enabled with LCR bit-3 set to a logic 1, LCR BIT-4 selects the even or odd parity format. • Logic 0 = ODD Parity is generated by forcing an odd number of logic 1’s in the transmitted character. The receiver must be programmed to check the same format (default). • Logic 1 = EVEN Parity is generated by forcing an even the number of logic 1’s in the transmitted character. The receiver must be programmed to check the same format. LCR[3]: TX and RX Parity Select Parity or no parity can be selected via this bit. The parity bit is a simple way used in communications for data integrity check. See Table 15 above for parity selection summary. • Logic 0 = No parity. • Logic 1 = A parity bit is generated during the transmission while the receiver checks for parity error of the data character received. 37 XR16V698 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO LCR[2]: TX and RX Stop-bit Length Select REV. 1.0.3 The length of stop bit is specified by this bit in conjunction with the programmed word length. BIT-2 0 1 1 WORD LENGTH STOP BIT LENGTH (BIT TIME(S)) 1 (default) 1-1/2 2 5,6,7,8 5 6,7,8 LCR[1:0]: TX and RX Word Length Select These two bits specify the word length to be transmitted or received. BIT-1 0 0 1 1 BIT-0 0 1 0 1 WORD LENGTH 5 (default) 6 7 8 4.7 Modem Control Register (MCR) - Read/Write The MCR register is used for controlling the modem interface signals or general purpose inputs/outputs. MCR[7]: Clock Prescaler Select • Logic 0 = Divide by one. The input clock from the crystal or external clock is fed directly to the Programmable Baud Rate Generator without further modification, i.e., divide by one (default). • Logic 1 = Divide by four. The prescaler divides the input clock from the crystal or external clock by four and feeds it to the Programmable Baud Rate Generator, hence, data rates become one forth. MCR[6]: Infrared Encoder/Decoder Enable The state of this bit depends on the sampled logic level of pin ENIR during power up, following a hardware reset (rising edge of RST# input). Afterward user can override this bit for desired operation. • Logic 0 = Enable the standard modem receive and transmit character interface. • Logic 1 = Enable infrared IrDA receive and transmit inputs/outputs. While in this mode, the TX/RX output/ input are routed to the infrared encoder/decoder. The data input and output levels will conform to the IrDA infrared interface requirement. As such, while in this mode the infrared TX output will be a logic 0 during idle data conditions. FCTR bit-4 may be selected to invert the RX input signal level going to the decoder for infrared modules that provide rather an inverted output. MCR[5]: Xon-Any Enable • Logic 0 = Disable Xon-Any function (default). • Logic 1 = Enable Xon-Any function. In this mode any RX character received will enable Xon, resume data transmission. MCR[4]: Internal Loopback Enable • Logic 0 = Disable loopback mode (default). • Logic 1 = Enable local loopback mode, see loopback section and Figure 11. 38 XR16V698 REV. 1.0.3 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO MCR[3]: Send Char Immediate (OP2 in Local Loopback Mode) This bit is used to transmit a character immediately irrespective of the bytes currently in the transmit FIFO. The data byte must be loaded into the transmit holding register (THR) immediately following the write to this bit (to set it to a ’1’). In other words, no other register must be accessed between setting this bit and writing to the THR. The loaded byte will be transmitted ahead of all the bytes in the TX FIFO, immediately after the character currently being shifted out of the transmit shift register is sent out. The existing line parameters (parity, stop bits) will be used when composing the character. This bit is self clearing, therefore, must be set before sending a custom characer each time. Please note that the Transmitter must be enabled for this function (MSR[3] = 0). Also, if software flow control is enabled, the software flow control characters (Xon, Xoff) have higher priority and will get shifted out before the custom byte is transmitted. • Logic 0 = Send Char Immediate disabled (default). • Logic 1 = Send Char Immediate enabled. In Local Loopback Mode (MCR[4] = 1), this bit acts as the legacy OP2 output and controls the CD bit in the MSR register as shown in Figure 11. Please make sure that this bit is a ’0’ when exiting the Local Loopback Mode. MCR[2]: DTR# or RTS# for Auto Flow Control (OP1 in Local Loopback Mode) DTR# or RTS# auto hardware flow control select. This bit is in effect only when auto RTS/DTR is enabled by EFR bit-6. DTR# selection is associated with DSR# and RTS# is with CTS#. • Logic 0 = Uses RTS# and CTS# pins for auto hardware flow control. • Logic 1 = Uses DTR# and DSR# pins for auto hardware flow control. In Local Loopback mode (MCR[4] = 1), this bit acts as the legacy OP1 output and controls the RI bit in the MSR register, as shown in Figure 11. MCR[1]: RTS# Output The RTS# pin may be used for automatic hardware flow control by enabled by EFR bit-6 and MCR bit-2=0. If the modem interface is not used, this output may be used for general purpose. • Logic 0 = Force RTS# output to a logic 1 (default). • Logic 1 = Force RTS# output to a logic 0. MCR[0]: DTR# Output The DTR# pin may be used for automatic hardware flow control enabled by EFR bit-6 and MCR bit-2=1. If the modem interface is not used, this output may be used for general purpose. • Logic 0 = Force DTR# output to a logic 1 (default). • Logic 1 = Force DTR# output to a logic 0. 4.8 Line Status Register (LSR) - Read Only This register provides the status of data transfers between the UART and the host. If IER bit-2 is set to a logic 1, an LSR interrupt will be generated immediately when any character in the RX FIFO has an error (parity, framing, overrun, break). LSR[7]: Receive FIFO Data Error Flag • Logic 0 = No FIFO error (default). • Logic 1 = An indicator for the sum of all error bits in the RX FIFO. At least one parity error, framing error or break indication is in the FIFO data. This bit clears when there are no more errors in the FIFO. 39 XR16V698 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO LSR[6]: Transmitter Empty Flag REV. 1.0.3 This bit is the Transmitter Empty indicator. This bit is set to a logic 1 whenever both the transmit FIFO (or THR, in non-FIFO mode) and the transmit shift register (TSR) are both empty. It is set to logic 0 whenever either the TX FIFO or TSR contains a data character. LSR[5]: Transmit FIFO Empty Flag This bit is the Transmit FIFO Empty indicator. This bit indicates that the transmitter is ready to accept a new character for transmission. This bit is set to a logic 1 when the last data byte is transferred from the transmit FIFO to the transmit shift register. The bit is reset to logic 0 as soon as a data byte is loaded into the transmit FIFO. In the non-FIFO mode this bit is set when the transmit holding register (THR) is empty; it is cleared when at a byte is written to the THR. LSR[4]: Receive Break Flag • Logic 0 = No break condition (default). • Logic 1 = The receiver received a break signal (RX was a logic 0 for one character frame time). In the FIFO mode, only one break character is loaded into the FIFO. The break indication remains until the RX input returns to the idle condition, “mark” or logic 1. LSR[3]: Receive Data Framing Error Flag • Logic 0 = No framing error (default). • Logic 1 = Framing error. The receive character did not have a valid stop bit(s). This error is associated with the character available for reading in RHR. LSR[2]: Receive Data Parity Error Flag • Logic 0 = No parity error (default). • Logic 1 = Parity error. The receive character in RHR (top of the FIFO) does not have correct parity information and is suspect. This error is associated with the character available for reading in RHR. LSR[1]: Receiver Overrun Flag • Logic 0 = No overrun error (default). • Logic 1 = Overrun error. A data overrun error condition occurred in the receive shift register. This happens when additional data arrives while the FIFO is full. In this case the previous data in the receive shift register is overwritten. Note that under this condition the data byte in the receive shift register is not transferred into the FIFO, therefore the data in the FIFO is not corrupted by the error. LSR[0]: Receive Data Ready Indicator • Logic 0 = No data in receive holding register or FIFO (default). • Logic 1 = Data has been received and is saved in the receive holding register or FIFO. 4.9 Modem Status Register (MSR) - Read Only This register provides the current state of the modem interface signals, or other peripheral device that the UART is connected. Lower four bits of this register are used to indicate the changed information. These bits are set to a logic 1 whenever a signal from the modem changes state. These bits may be used as general purpose inputs/outputs when they are not used with modem signals. MSR[7]: CD Input Status Normally this bit is the complement of the CD# input. In the loopback mode this bit is equivalent to bit-3 in the MCR register. The CD# input may be used as a general purpose input when the modem interface is not used. 40 XR16V698 REV. 1.0.3 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO MSR[6]: RI Input Status Normally this bit is the complement of the RI# input. In the loopback mode this bit is equivalent to bit-2 in the MCR register. The RI# input may be used as a general purpose input when the modem interface is not used. MSR[5]: DSR Input Status DSR# pin may function as automatic hardware flow control signal input if it is enabled and selected by Auto CTS/DSR bit (EFR bit-6=1) and RTS/DTR flow control select bit (MCR bit-2=1). Auto CTS/DSR flow control allows starting and stopping of local data transmissions based on the modem DSR# signal. A HIGH on the DSR# pin will stop UART transmitter as soon as the current character has finished transmission, and a LOW will resume data transmission. Normally MSR bit-5 is the complement of the DSR# input. However in the loopback mode, this bit is equivalent to the DTR# bit in the MCR register. The DSR# input may be used as a general purpose input when the modem interface is not used. MSR[4]: CTS Input Status CTS# pin may function as automatic hardware flow control signal input if it is enabled and selected by Auto CTS/DSR bit (EFR bit-6=1) and RTS/DTR flow control select bit (MCR bit-2=0). Auto CTS/DSR flow control allows starting and stopping of local data transmissions based on the modem CTS# signal. A HIGH on the CTS# pin will stop UART transmitter as soon as the current character has finished transmission, and a LOW will resume data transmission. Normally MSR bit-4 is the complement of the CTS# input. However in the loopback mode, this bit is equivalent to the RTS# bit in the MCR register. The CTS# input may be used as a general purpose input when the modem interface is not used. MSR[3]: Delta CD# Input Flag • Logic 0 = No change on CD# input (default). • Logic 1 = Indicates that the CD# input has changed state since the last time it was monitored. A modem status interrupt will be generated if MSR interrupt is enabled (IER bit-3). MSR[2]: Delta RI# Input Flag • Logic 0 = No change on RI# input (default). • Logic 1 = The RI# input has changed from a logic 0 to a logic 1, ending of the ringing signal. A modem status interrupt will be generated if MSR interrupt is enabled (IER bit-3). MSR[1]: Delta DSR# Input Flag • Logic 0 = No change on DSR# input (default). • Logic 1 = The DSR# input has changed state since the last time it was monitored. A modem status interrupt will be generated if MSR interrupt is enabled (IER bit-3). MSR[0]: Delta CTS# Input Flag • Logic 0 = No change on CTS# input (default). • Logic 1 = The CTS# input has changed state since the last time it was monitored. A modem status interrupt will be generated if MSR interrupt is enabled (IER bit-3). 4.10 Modem Status Register (MSR) - Write Only The upper four bits [7:4] of this register set the delay in number of bits time for the auto RS-485 turn around from transmit to receive. MSR[7:4] When Auto RS-485 feature is enabled (FCTR bit-5=1) and RTS# output is connected to the enable input of a RS-485 transceiver. These 4 bits select from 0 to 15 bit-time delay after the end of the last stop-bit of the last transmitted character. This delay controls when to change the state of RTS# output. This delay is very useful in long-cable networks. Table 16 shows the selection. The bits are enabled by EFR bit-4. 41 XR16V698 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO REV. 1.0.3 TABLE 16: AUTO RS-485 HALF-DUPLEX DIRECTION CONTROL DELAY FROM TRANSMIT-TO-RECEIVE MSR[7] 0 0 0 0 0 9 0 0 1 1 1 1 1 1 1 1 MSR[6] 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 MSR[5] 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 MSR[4] 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 DELAY IN DATA BIT(S) TIME 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 MSR[3]: Transmitter Disable This bit can be used to disable the transmitter by halting the Transmit Shift Register (TSR). When this bit is set to a ’1’, the bytes already in the FIFO will not be sent out. Also, any more data loaded into the FIFO will stay in the FIFO and will not be sent out. When this bit is set to a ’0’, the bytes currently in the TX FIFO will be sent out. Please note that setting this bit to a ’1’ stops any character from going out. Also, this bit must be a ’0’ for Send Char Immediate function (see MCR[3]). • Logic 0 = Enable Transmitter (default). • Logic 1 = Disable Transmitter. 42 XR16V698 REV. 1.0.3 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO MSR[2]: Receiver Disable This bit can be used to disable the receiver by halting the Receive Shift Register (RSR). When this bit is set to a logic 1, the receiver will operate in one of the following ways: ■ ■ If a character is being received at the time of setting this bit, that character will be correctly received. No more characters will be received. If the receiver is idle at the time of setting this bit, one character will still be received fully. No more characters will be received. The receiver can be enabled and will start receiving characters by resetting this bit to a logic 0. The receiver will operate in one of the following ways: ■ ■ If the receiver is idle (RX pin is HIGH) at the time of setting this bit, the next character will be received normally. It is recommended that the receiver be idle when resetting this bit to a logic 0. If the receiver is not idle (RX pin is toggling) at the time of setting this bit, the RX FIFO will be filled with unknown data. Any data that is in the RX FIFO can be read out at any time whether the receiver is disabled or not. • Logic 0 = Enable Receiver (default). • Logic 1 = Disable Receiver. MSR[1]: Reserved MSR[0]: 9-bit or Multidrop Mode Enable This bit enables 9-bit or Multidrop mode. See “Section 2.13, Auto RS-485 Half-duplex Control” on page 18 for complete details. • Logic 0 = Normal 8-bit mode • Logic 1 = Enable 9-bit or Multidrop mode 4.11 Scratch Pad Register (SPR) - Read/Write This is a 8-bit general purpose register for the user to store temporary data. The content of this register is preserved during sleep mode but becomes 0xFF (default) after a reset or a power off-on cycle. 4.12 Feature Control Register (FCTR) - Read/Write This register controls the UART enhanced functions that are not available on ST16C554 or ST16C654. FCTR[7:6]: Reserved FCTR[5]: Auto RS-485 Enable Auto RS-485 half duplex control enable/disable. • Logic 0 = Standard ST16C550 mode. Transmitter generates an interrupt when transmit holding register (THR) becomes empty. Transmit Shift Register (TSR) may still be shifting data bit out. • Logic 1 = Enable Auto RS-485 half duplex direction control. RTS# output changes its logic level from HIGH to LOW when finished sending the last stop bit of the last character out of the TSR register. It changes from LOW to HIGH when a data byte is loaded into the THR or transmit FIFO. The change to HIGH occurs prior sending the start-bit. It also changes the transmitter interrupt from transmit holding to transmit shift register (TSR) empty. FCTR[4]: Infrared RX Input Logic Select • Logic 0 = Select RX input as active HIGH encoded IrDA data, normal, (default). • Logic 1 = Select RX input as active LOW encoded IrDA data, inverted. FCTR [3:0] - Reserved 43 XR16V698 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO 4.13 Enhanced Feature Register (EFR) - Read/Write REV. 1.0.3 Enhanced features are enabled or disabled using this register. Bits 3:0 provide single or dual consecutive character software flow control selection (see Table 17). When the Xon1 and Xon2 and Xoff1 and Xoff2 modes are selected, the double 8-bit words are concatenated into two sequential characters. Caution: note that whenever changing the TX or RX flow control bits, always reset all bits back to logic 0 (disable) before programming a new setting. EFR[7]: Auto CTS Flow Control Enable Automatic CTS or DSR Flow Control. • Logic 0 = Automatic CTS/DSR flow control is disabled (default). • Logic 1 = Enable Automatic CTS/DSR flow control. Transmission stops when CTS/DSR# pin de-asserts (HIGH). Transmission resumes when CTS/DSR# pin is asserted (LOW). The selection for CTS# or DSR# is through MCR bit-2. EFR[6]: Auto RTS or DTR Flow Control Enable RTS#/DTR# output may be used for hardware flow control by setting EFR bit-6 to logic 1. When Auto RTS/ DTR is selected, an interrupt will be generated when the receive FIFO is filled to the programmed trigger level and RTS/DTR# will de-assert (HIGH) at the next upper trigger. RTS/DTR# will re-assert (LOW) when FIFO data falls below the next lower trigger. The RTS# or DTR# output must be asserted (LOW) before the auto RTS/DTR can take effect. The selection for RTS# or DTR# is through MCR bit-2. RTS/DTR# pin will function as a general purpose output when hardware flow control is disabled. • Logic 0 = Automatic RTS/DTR flow control is disabled (default). • Logic 1 = Enable Automatic RTS/DTR flow control. EFR[5]: Special Character Detect Enable • Logic 0 = Special Character Detect Disabled (default). • Logic 1 = Special Character Detect Enabled. The UART compares each incoming receive character with data in Xoff-2 register. If a match exists, the received data will be transferred to FIFO and ISR bit-4 will be set to indicate detection of the special character. Bit-0 corresponds with the LSB bit for the receive character. If flow control is set for comparing Xon1, Xoff1 (EFR [1:0]=10) then flow control and special character work normally. However, if flow control is set for comparing Xon2, Xoff2 (EFR[1:0]=01) then flow control works normally, but Xoff2 will not go to the FIFO, and will generate an Xoff interrupt and a special character interrupt. EFR[4]: Enhanced Function Bits Enable Enhanced function control bit. This bit enables the enhanced functions in IER bits 7:5, ISR bits 5:4, FCR bits 5:4, MCR bits 7:5, 3:2 and MSR 7:2 bits to be modified. After modifying any enhanced bits, EFR bit-4 can be set to a logic 0 to latch the new values. This feature prevents legacy software from altering or overwriting the enhanced functions once set. Normally, it is recommended to leave it enabled, logic 1. • Logic 0 = modification disable/latch enhanced features. IER bits 7:5, ISR bits 5:4, FCR bits 5:4, MCR bits 7:5, 3:2 and MSR 7:2 bits are saved to retain the user settings. After a reset, all these bits are set to a logic 0 to be compatible with ST16C550 mode (default). • Logic 1 = Enables the enhanced functions. When this bit is set to a logic 1 all enhanced features are enabled. 44 XR16V698 REV. 1.0.3 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO EFR[3:0]: Software Flow Control Select Combinations of software flow control can be selected by programming these bits, as shown in Table 17 below. TABLE 17: SOFTWARE FLOW CONTROL FUNCTIONS EFR BIT-3 0 0 1 0 1 X X X 1 EFR BIT-2 0 0 0 1 1 X X X 0 EFR BIT-1 0 X X X X 0 1 0 1 EFR BIT-0 0 X X X X 0 0 1 1 TRANSMIT AND RECEIVE SOFTWARE FLOW CONTROL No TX and RX flow control (default and reset) No transmit flow control Transmit Xon1, Xoff1 Transmit Xon2, Xoff2 Transmit Xon1 and Xon2, Xoff1 and Xoff2 No receive flow control Receiver compares Xon1, Xoff1 Receiver compares Xon2, Xoff2 Transmit Xon1, Xoff1 Receiver compares Xon1 or Xon2, Xoff1 or Xoff2 Transmit Xon2, Xoff2 Receiver compares Xon1 or Xon2, Xoff1 or Xoff2 Transmit Xon1 and Xon2, Xoff1 and Xoff2 Receiver compares Xon1 and Xon2, Xoff1 and Xoff2 No transmit flow control Receiver compares Xon1 and Xon2, Xoff1 and Xoff2 0 1 1 1 1 1 1 1 0 0 1 1 4.14 XOFF1, XOFF2, XON1 and XON2 Registers - Write Only These registers are used to program the Xoff1, Xoff2, Xon1 and Xon2 control characters respectively. 45 XR16V698 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO 4.15 XCHAR Register - Read Only REV. 1.0.3 This register gives the status of the last sent control character (xon or xoff) and the last received control character (xon or xoff). This register will be reset to 0x00 if, at anytime, the Software Flow Control is disabled. XCHAR [7:4] : Reserved XCHAR [3]: Transmit Xon Indicator If the last transmitted control character was a xon character or characters (xon1, xon2), this bit will be set to a logic 1. This bit will clear after the read. XCHAR [2]: Transmit Xoff Indicator If the last transmitted control character was a xoff character or characters (xoff1, xoff2), this bit will be set to a logic 1. This bit will clear after the read. XCHAR [1]: Xon Detect Indicator If the last received control character was a xon character or characters (xon1, xon2), this bit will be set to a logic 1. This bit will clear after the read. XCHAR [0]: Xoff Detect Indicator If the last received control character was a xoff character or characters (xoff1, xoff2), this bit will be set to a logic 1. This bit will clear after the read. 46 XR16V698 REV. 1.0.3 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO TABLE 18: UART RESET CONDITIONS REGISTERS DLL DLM DLD RHR THR IER FCR ISR LCR MCR LSR MSR RESET STATE Bits 7-0 = 0x01 Bits 7-0 = 0x00 Bits 7-0 = 0x00 Bits 7-0 = 0xXX Bits 7-0 = 0xXX Bits 7-0 = 0x00 Bits 7-0 = 0x00 Bits 7-0 = 0x01 Bits 7-0 = 0x00 Bits 7-0 = 0x00 Bits 7-0 = 0x60 Bits 3-0 = logic 0 Bits 7-4 = logic levels of the inputs Bits 7-0 = 0xFF Bits 7-0 = 0x00 Bits 7-0 = 0x00 Bits 7-0 = 0x00 Bits 7-0 = 0x00 Bits 7-0 = 0x00 Bits 7-0 = 0x00 Bits 7-0 = 0x00 Bits 7-0 = 0x00 Bits 7-0 = 0x00 Bits 7-0 = 0x00 Bits 7-0 = 0x00 I/O SIGNALS TX[7:0] IRTX[7:0] RTS#[7:0] DTR#[7:0] RESET STATE HIGH LOW HIGH HIGH SPR FCTR EFR TFCNT TFTRG RFCNT RFTRG XCHAR XON1 XON2 XOFF1 XOFF2 47 XR16V698 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO REV. 1.0.3 ABSOLUTE MAXIMUM RATINGS Power Supply Range Voltage at Any Pin Operating Temperature Storage Temperature Package Dissipation Thermal Resistance (14x20x3.0mm 100-QFP) 4 Volts -0.5 to 5.5V -40o to +85o C -65o to +150o C 500 mW θ-ja = 34°C/W , θ-jc = 9°C/W ELECTRICAL CHARACTERISTICS DC ELECTRICAL CHARACTERISTICS TA=0o to 70oC (-40o to +85oC for industrial grade package), Vcc is 2.25V to 3.6V SYMBOL VILCK VIHCK VIL VIH VOL PARAMETER Clock input low level Clock input high level Input Low Voltage Input High Voltage Output Low Voltage 0.4 VOH Output High Voltage 1.8 IIL IIH CIN ICC Input Low Leakage Current Input High Leakage Current Input Pin Capacitance Power Supply Current -10 10 5 1.5 -10 10 5 2.5 2.4 V V uA uA pF mA EXT Clock=2MHz A7-A0 at GND, all inputs at VCC or GND and outputs unloaded Eight UARTs asleep. A7-A0 at GND, all inputs at VCC or GND and outputs unloaded. 2.5V MIN -0.3 1.8 -0.3 1.8 2.5V MAX 3.3V MIN -0.3 2.4 -0.3 2.0 3.3 MAX UNITS V V V V V CONDITIONS 0.6 5.5 0.5 5.5 0.6 5.5 0.7 5.5 0.4 IOL = 6mA IOL = 3mA IOH = -6mA IOH = -3mA ISLEEP Sleep Current 30 30 uA 48 XR16V698 REV. 1.0.3 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO AC ELECTRICAL CHARACTERISTICS TA=0o to 70oC (-40o to +85oC for industrial grade package), Vcc is 2.25V to 3.6V, 70 pF Load where applicable SYMBOL TC1,TC2 TOSC TECK TAS TAH TCS TDY TRD TWR TRDV TWDS TRDH TWDH TADS TADH TRWS TRDA TRDH TWDS TWDH TRWH TCSL TCSD TWDO TMOD TRSI TSSI TRRI Clock Pulse Period Crystal Frequency External Clock Frequency Address Setup (16 Mode) Address Hold (16 Mode) Chip Select Width (16 Mode) Delay between CS# Active Cycles (16 Mode) Read Strobe Width (16 Mode) Write Strobe Width (16 Mode) Read Data Valid (16 Mode) Write Data Setup (16 Mode) Read Data Hold (16 Mode) Write Data Hold (16 Mode) Address Setup (68 Mode) Address Hold (68 Mode) R/W# Setup to CS# (68 Mode) Read Data Access (68 mode) Read Data Hold (68 mode) Write Data Setup (68 mode) Write Data Hold (68 Mode) CS# De-asserted to R/W# De-asserted (68 Mode) CS# Width (68 Mode) CS# Cycle Delay (68 Mode) Delay from IOW# to Modem Output Delay to set Interrupt from Modem Input Delay To Reset Interrupt From IOR# Delay From Stop To Set Interrupt Delay From IOR# To Reset Interrupt 5 7 3 25 25 50 50 50 1 45 7 3 3 3 20 10 5 7 3 25 25 50 50 50 1 45 5 10 7 3 3 3 20 10 3 3 25 25 25 25 20 5 10 PARAMETER 2.5V MIN 10 24 40 3 3 25 25 25 25 20 2.5V MAX 3.3V MIN 7 24 60 3.3V MAX UNITS ns MHz MHz ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns Bclk ns 49 XR16V698 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO AC ELECTRICAL CHARACTERISTICS REV. 1.0.3 TA=0o to 70oC (-40o to +85oC for industrial grade package), Vcc is 2.25V to 3.6V, 70 pF Load where applicable SYMBOL TSI TWRI TRST Bclk PARAMETER Delay From Stop To Interrupt Delay From IOW# To Reset Interrupt Reset Pulse Baud Clock 40 2.5V MIN 2.5V MAX 45 45 40 3.3V MIN 3.3V MAX 45 45 UNITS ns ns ns Hz 16X or 8X or 4X of data rate 50 XR16V698 REV. 1.0.3 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO FIGURE 16. 16 MODE (INTEL) DATA BUS READ AND WRITE TIMING A0-A7 TAS Valid Address TAS Valid Address TAH TCS TAH CS# TDY TRD IOR# TRDV D0-D7 Valid Data TRDH TRDV Valid Data TRDH 16Read 16 Mode (Intel) Data Bus Read Timing A0-A7 TAS Valid Address TAS Valid Address TAH TCS TAH CS# TDY TWR IOW# TWDS D0-D7 Valid Data TWDH TWDS Valid Data TWDH 16Write 16 Mode (Intel) Data Bus Write Timing 51 XR16V698 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO FIGURE 17. 68 MODE (MOTOROLA) DATA BUS READ AND WRITE TIMING REV. 1.0.3 A0-A7 TADS Valid Address Valid Address TCSL TADH CS# TRWS TCSD R/W# TRWH TRDH TRDA D0-D7 Valid Data Valid Data 68Read 68 Mode (Motorola) Data Bus Read Timing A0-A7 TADS Valid Address Valid Address TCSL TADH CS# TRWS TCSD R/W# TRWH TWDS D0-D7 TWDH Valid Data Valid Data 68Write 68 Mode (Motorola) Data Bus Write Timing 52 XR16V698 REV. 1.0.3 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO FIGURE 18. MODEM INPUT/OUTPUT TIMING IOW # Active T W DO RTS# DTR# Change of state Change of state CD# CTS# DSR# T MOD INT Change of state Change of state T MO D Active T RSI Active Active IOR# Active Active Active T M OD RI# Change of state FIGURE 19. RECEIVE INTERRUPT TIMING [NON-FIFO MODE] RX Start Bit Stop Bit D0:D7 D0:D7 D0:D7 INT# 1 Byte in RHR 1 Byte in RHR 1 Byte in RHR T RR T RR T RR IO R# (Reading data out of RHR) 53 XR16V698 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO FIGURE 20. TRANSMIT INTERRUPT TIMING [NON-FIFO MODE] TX (U n lo a d in g ) IE R [1 ] e n a b le d S ta rt B it S to p B it REV. 1.0.3 D 0 :D 7 D 0 :D 7 D 0 :D 7 IS R is re a d IS R is re a d IS R is re a d IN T # * TW RI TW RI TW RI IO W # (L o a d in g d a ta in to T H R ) *T X in te rru p t is c le a re d w h e n th e IS R is re a d o r w h e n d a ta is lo a d e d in to th e T H R . FIGURE 21. RECEIVE INTERRUPT TIMING [FIFO MODE] Start Bit RX S D0:D7 S D0:D7 T D0:D7 T SSI S D0:D7 T S D0:D7 T S D0:D7 T S D0:D7 T INT# RX FIFO fills up to RX Trigger Level or RX Data Tim eout RX FIFO drops below RX Trigger Level T RRI T RR IOR# (Reading data out of RX FIFO) FIGURE 22. TRANSMIT INTERRUPT TIMING [FIFO MODE] Start B it S top Bit Last Data B yte Transm itted S D 0:D 7 TS TX FIFO Em pty TX (Unloading) IER [1] enabled S D 0:D 7 T D 0:D 7 T T SI TS D0:D 7 T S D 0:D 7 T ISR is read S D 0:D 7 T ISR is read INT#* TX FIFO fills up to trigger level TW RI TX FIFO drops below trigger level IO W # (Loading data into FIFO ) *TX interrupt is cleared when the ISR is read or when TX FIFO fills up to the trigger level. 54 XR16V698 REV. 1.0.3 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO PACKAGE DIMENSIONS 100 LEAD PLASTIC QUAD FLAT P (14 mm x 20 mm, QFP) Rev. 2.00 D D1 80 51 81 50 E1 E 100 31 1 30 A2 B e C A Seating Plane A1 α L SYMBOL A A1 A2 B C D D1 E E1 e L α 1.95 mm Form INCHES MILLIMETERS MIN MAX MIN MAX 0.102 0.134 2.60 3.40 0.002 0.014 0.05 0.35 0.100 0.120 2.55 3.05 0.009 0.015 0.22 0.38 0.005 0.009 0.13 0.23 0.931 0.951 23.65 24.15 0.783 0.791 19.90 20.10 0.695 0.715 17.65 18.15 0.547 0.555 13.90 14.10 0.0256 BSC 0.65 BSC 0.026 0.037 0.65 0.95 0° 7° 0° 7° Note: The control dimension is the millimeter column 55 XR16V698 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO REVISION HISTORY REV. 1.0.3 REVISION P1.0.0 1.0.0 1.0.1 1.0.2 1.0.3 DATE July 2007 Preliminary Datasheet. DESCRIPTION November 2007 Final Datasheet. Updated DC and AC Electrical Specs. December 2007 Datasheet correction. Removed reference to TXCNT and RXCNT registers since the XR16V698 does not have this feature. January 2008 July 2008 Corrected Ordering Part Number. Corrected description of Xon/Xoff/Special character interrupt. NOTICE EXAR Corporation reserves the right to make changes to the products contained in this publication in order to improve design, performance or reliability. EXAR Corporation assumes no responsibility for the use of any circuits described herein, conveys no license under any patent or other right, and makes no representation that the circuits are free of patent infringement. Charts and schedules contained here in are only for illustration purposes and may vary depending upon a user’s specific application. While the information in this publication has been carefully checked; no responsibility, however, is assumed for inaccuracies. EXAR Corporation does not recommend the use of any of its products in life support applications where the failure or malfunction of the product can reasonably be expected to cause failure of the life support system or to significantly affect its safety or effectiveness. Products are not authorized for use in such applications unless EXAR Corporation receives, in writing, assurances to its satisfaction that: (a) the risk of injury or damage has been minimized; (b) the user assumes all such risks; (c) potential liability of EXAR Corporation is adequately protected under the circumstances. Copyright 2008 EXAR Corporation Datasheet July 2008. Send your UART technical inquiry with technical details to hotline: uarttechsupport@exar.com. Reproduction, in part or whole, without the prior written consent of EXAR Corporation is prohibited. 56 XR16V698 REV. 1.0.3 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO TABLE OF CONTENTS GENERAL DESCRIPTION................................................................................................ 1 APPLICATIONS .............................................................................................................................................. 1 FEATURES .................................................................................................................................................... 1 FIGURE 1. BLOCK DIAGRAM ............................................................................................................................................................. 1 FIGURE 2. PIN OUT OF THE DEVICE.................................................................................................................................................. 2 ORDERING INFORMATION .............................................................................................................................. 2 PIN DESCRIPTIONS ........................................................................................................ 3 1.0 DESCRIPTION ......................................................................................................................................... 7 2.0 FUNCTIONAL DESCRIPTIONS .............................................................................................................. 7 2.1 DEVICE RESET ................................................................................................................................................... 7 2.1.1 HARDWARE RESET....................................................................................................................................................... 7 2.1.2 SOFTWARE RESET ....................................................................................................................................................... 7 2.2 UART CHANNEL SELECTION ........................................................................................................................... 7 TABLE 1: UART CHANNEL SELECTION ............................................................................................................................................. 7 2.3 SIMULTANEOUS WRITE TO ALL CHANNELS ................................................................................................. 7 2.4 INT# OUPUT ........................................................................................................................................................ 8 TABLE 2: INT# PIN OPERATION FOR TRANSMITTER ........................................................................................................................... 8 TABLE 3: INT# PIN OPERATION FOR RECEIVER ................................................................................................................................ 8 2.5 CRYSTAL OSCILLATOR .................................................................................................................................... 8 FIGURE 3. TYPICAL OSCILLATOR CONNECTIONS................................................................................................................................. 8 2.6 PROGRAMMABLE BAUD RATE GENERATOR WITH FRACTIONAL DIVISOR ............................................. 9 FIGURE 4. BAUD RATE GENERATOR ............................................................................................................................................... 10 TABLE 4: TYPICAL DATA RATES WITH A 24 MHZ CRYSTAL OR EXTERNAL CLOCK AT 16X SAMPLING ................................................... 10 2.7 TRANSMITTER.................................................................................................................................................. 11 2.7.1 TRANSMIT HOLDING REGISTER (THR) - WRITE ONLY........................................................................................... 2.7.2 TRANSMITTER OPERATION IN NON-FIFO MODE .................................................................................................... FIGURE 5. TRANSMITTER OPERATION IN NON-FIFO MODE .............................................................................................................. 2.7.3 TRANSMITTER OPERATION IN FIFO MODE ............................................................................................................. FIGURE 6. TRANSMITTER OPERATION IN FIFO AND FLOW CONTROL MODE ..................................................................................... 11 11 11 12 12 2.8 RECEIVER ......................................................................................................................................................... 12 2.8.1 RECEIVE HOLDING REGISTER (RHR) - READ-ONLY .............................................................................................. 12 FIGURE 7. RECEIVER OPERATION IN NON-FIFO MODE .................................................................................................................... 13 FIGURE 8. RECEIVER OPERATION IN FIFO AND AUTO RTS FLOW CONTROL MODE ......................................................................... 13 2.9 THR AND RHR REGISTER LOCATIONS ......................................................................................................... 13 TABLE 5: TRANSMIT AND RECEIVE HOLDING REGISTER LOCATIONS, 16C550 COMPATIBLE ............................................................... 14 2.10 AUTO RTS/DTR HARDWARE FLOW CONTROL OPERATION.................................................................... 14 2.10.1 AUTO CTS/DSR FLOW CONTROL............................................................................................................................ 15 FIGURE 9. AUTO RTS/DTR AND CTS/DSR FLOW CONTROL OPERATION ........................................................................................ 16 2.11 AUTO XON/XOFF (SOFTWARE) FLOW CONTROL...................................................................................... 17 TABLE 6: AUTO XON/XOFF (SOFTWARE) FLOW CONTROL ............................................................................................................... 17 2.12 SPECIAL CHARACTER DETECT.................................................................................................................. 17 2.13 AUTO RS-485 HALF-DUPLEX CONTROL .................................................................................................... 18 2.13.1 NORMAL MULTIDROP MODE ................................................................................................................................... 18 2.13.2 AUTO ADDRESS DETECTION .................................................................................................................................. 18 2.14 INFRARED MODE ........................................................................................................................................... 19 FIGURE 10. INFRARED TRANSMIT DATA ENCODING AND RECEIVE DATA DECODING .......................................................................... 19 2.15 SLEEP MODE WITH AUTO WAKE-UP ......................................................................................................... 20 2.16 INTERNAL LOOPBACK.................................................................................................................................. 21 FIGURE 11. INTERNAL LOOP BACK ................................................................................................................................................. 21 3.0 XR16V698 REGISTERS ....................................................................................................................... 22 FIGURE 12. THE XR16V698 REGISTERS ........................................................................................................................................ 22 3.1 DEVICE CONFIGURATION REGISTER SET.................................................................................. 23 TABLE 7: XR16V698 REGISTER SETS ............................................................................................................................................ 23 TABLE 8: DEVICE CONFIGURATION REGISTERS ............................................................................................................................... 24 3.1.1 THE GLOBAL INTERRUPT SOURCE REGISTERS.................................................................................................... 24 3.1.1.1 INT0 CHANNEL INTERRUPT INDICATOR ................................................................................................................. 25 3.1.1.2 INT1, INT2 AND INT3 INTERRUPT SOURCE LOCATOR ........................................................................................... 25 FIGURE 13. THE GLOBAL INTERRUPT REGISTERS, INT0, INT1, INT2 AND INT3 .............................................................................. 25 TABLE 9: UART CHANNEL [7:0] INTERRUPT SOURCE ENCODING AND CLEARING ............................................................................. 26 I XR16V698 2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO REV. 1.0.3 3.1.2 GENERAL PURPOSE 16-BIT TIMER/COUNTER [TIMERMSB, TIMELSB, TIMER, TIMECNTL] (DEFAULT 0XXX-XX00-00).............................................................................................................................................................................. 26 3.1.2.1 TIMERMSB [7:0] AND TIMERLSB [7:0] ............................................................................................................. 26 3.1.2.2 TIMER [7:0] RESERVED ....................................................................................................................................... 26 3.1.2.3 TIMERCNTL [7:0] REGISTER .............................................................................................................................. 26 TABLE 10: TIMER CONTROL COMMANDS ....................................................................................................................................... 27 TIMER OPERATION ................................................................................................................................................ 27 FIGURE 14. TIMER/COUNTER CIRCUIT ............................................................................................................................................. FIGURE 15. INTERRUPT OUTPUT IN ONE-SHOT AND RE-TRIGGERABLE MODES ................................................................................. 3.1.3 8XMODE [7:0] (DEFAULT 0X00).................................................................................................................................. 3.1.4 4XMODE [7:0] (DEFAULT 0X00).................................................................................................................................. 3.1.5 RESET [7:0] (DEFAULT 0X00) ..................................................................................................................................... 3.1.6 SLEEP [7:0] (DEFAULT 0X00) ..................................................................................................................................... 3.1.7 DEVICE IDENTIFICATION AND REVISION ................................................................................................................. 3.1.7.1 DVID [7:0] (DEFAULT 0X68) ................................................................................................................................. 3.1.7.2 DREV [7:0] (DEFAULT (0X01) .............................................................................................................................. 3.1.8 REGB [7:0] (DEFAULT 0X00) ...................................................................................................................................... 27 28 28 28 29 29 29 29 29 29 3.2 UART CHANNEL CONFIGURATION REGISTERS .......................................................................................... 30 TABLE 11: UART CHANNEL CONFIGURATION REGISTERS ............................................................................................................... 30 TABLE 12: UART CHANNEL CONFIGURATION REGISTERS DESCRIPTION. SHADED BITS ARE ENABLED BY EFR BIT-4. ........................ 31 4.0 INTERNAL REGISTER DESCRIPTIONS............................................................................................... 32 4.1 RECEIVE HOLDING REGISTER (RHR) - READ ONLY ................................................................................... 32 4.2 TRANSMIT HOLDING REGISTER (THR) - WRITE ONLY................................................................................ 32 4.3 INTERRUPT ENABLE REGISTER (IER) - READ/WRITE................................................................................. 32 4.3.1 IER VERSUS RECEIVE FIFO INTERRUPT MODE OPERATION ............................................................................... 32 4.3.2 IER VERSUS RECEIVE/TRANSMIT FIFO POLLED MODE OPERATION .................................................................. 32 4.4 INTERRUPT STATUS REGISTER (ISR) - READ ONLY................................................................................... 34 4.4.1 INTERRUPT GENERATION: ........................................................................................................................................ 34 4.4.2 INTERRUPT CLEARING: ............................................................................................................................................. 34 TABLE 13: INTERRUPT SOURCE AND PRIORITY LEVEL ..................................................................................................................... 35 4.5 FIFO CONTROL REGISTER (FCR) - WRITE ONLY......................................................................................... 35 TABLE 14: TRANSMIT AND RECEIVE FIFO TRIGGER TABLE AND LEVEL SELECTION .......................................................................... 36 4.6 LINE CONTROL REGISTER (LCR) - READ/WRITE......................................................................................... 36 TABLE 15: PARITY PROGRAMMING .................................................................................................................................................. 37 4.7 MODEM CONTROL REGISTER (MCR) - READ/WRITE .................................................................................. 4.8 LINE STATUS REGISTER (LSR) - READ ONLY.............................................................................................. 4.9 MODEM STATUS REGISTER (MSR) - READ ONLY ....................................................................................... 4.10 MODEM STATUS REGISTER (MSR) - WRITE ONLY .................................................................................... 38 39 40 41 TABLE 16: AUTO RS-485 HALF-DUPLEX DIRECTION CONTROL DELAY FROM TRANSMIT-TO-RECEIVE ................................................ 42 4.11 SCRATCH PAD REGISTER (SPR) - READ/WRITE ....................................................................................... 43 4.12 FEATURE CONTROL REGISTER (FCTR) - READ/WRITE............................................................................ 43 4.13 ENHANCED FEATURE REGISTER (EFR) - READ/WRITE ........................................................................... 44 TABLE 17: SOFTWARE FLOW CONTROL FUNCTIONS ........................................................................................................................ 45 4.14 XOFF1, XOFF2, XON1 AND XON2 REGISTERS - WRITE ONLY.................................................................. 45 4.15 XCHAR REGISTER - READ ONLY ................................................................................................................ 46 TABLE 18: UART RESET CONDITIONS ............................................................................................................................................ 47 ABSOLUTE MAXIMUM RATINGS.................................................................................. 48 ELECTRICAL CHARACTERISTICS ............................................................................... 48 DC ELECTRICAL CHARACTERISTICS ............................................................................................................. 48 AC ELECTRICAL CHARACTERISTICS ............................................................................................................. 49 FIGURE 16. 16 MODE (INTEL) DATA BUS READ AND WRITE TIMING ................................................................................................. FIGURE 17. 68 MODE (MOTOROLA) DATA BUS READ AND WRITE TIMING ........................................................................................ FIGURE 18. MODEM INPUT/OUTPUT TIMING .................................................................................................................................... FIGURE 19. RECEIVE INTERRUPT TIMING [NON-FIFO MODE]........................................................................................................... FIGURE 20. TRANSMIT INTERRUPT TIMING [NON-FIFO MODE]......................................................................................................... FIGURE 21. RECEIVE INTERRUPT TIMING [FIFO MODE]................................................................................................................... FIGURE 22. TRANSMIT INTERRUPT TIMING [FIFO MODE]................................................................................................................. 51 52 53 53 54 54 54 PACKAGE DIMENSIONS................................................................................................ 55 REVISION HISTORY...................................................................................................................................... 56 II