XRD9836ACG-F

xr XRD9836 16-BIT PIXEL GAIN AFE JUNE 2003 REV. 1.0.0 GENERAL DESCRIPTION • Sampling rates from 1.0 MSPS to 10.0 MSPS per chan- The XRD9836 is a precision 16-bit analog front-end (AFE) for use in 3-channel/1-channel CCD/CIS document imaging applications. Pixel-by-pixel gain and offset for each of the 3 channels are controlled using a time multiplexed parallel input. Offset and Gain are sequentially supplied for red, green, and blue. The outputs from each of the three channels are transmitted time multiplexed with the high order byte first followed by the low order byte for red, blue and green. FEATURES • 16-bit resolution ADC, 30MHz Sampling Rate • 10-bit accurate linear programmable gain range selectable as either 2-to-20 V/V or 1-to-10 V/V per channel • Fully-differential input pins and internal path nel for 3 -Channel mode and up to 15.0 MSPS in single channel mode. • Pixel-by-Pixel Offset and Gain control through a parallel interface running at a maximum 60 Mbyte/sec. data rate • A microprocessor serial port to control various modes of operation • Fixed Gain/Offset Mode (FGOM) or Pixel by Pixel Gain/ Offset Mode (PPGOM) • Alternate Pixel Offset Adjust Mode (APOAM) • Low Power CMOS=280mW (typ. @ 3V); Power-Down Mode=1mW (typ. @ 3V with static clocks) • Single Power Supply (3.0 to 3.6 Volts) with Max CCD input signal of 1V and reset pulse up to 0.5V • High ESD Protection: 2000 Volts Minimum APPLICATIONS • Scanners, MFP’s FIGURE 1. BLOCK DIAGRAM GRN+ REDRED+ IE GRNBLUE+ BLUE- CAPP CAPN CMREF REXT ANALOG INPUTS RED GAIN REGISTER RED OFFSET REGISTER OFFSET/GAIN INPUT 10 Red Gain 10 10 Red Offset GREEN GAIN Green Gain REGISTER 10 10 GREEN OFFSET REGISTER Green Offset BLUE GAIN REGISTER BLUE OFFSET REGISTER Blue Gain 10 10 Blue Offset RED CDS & PGA Green CDS & PGA BIAS RED HIGH ORDER ADC OUT RED LOW ORDER ADC OUT XRD9836 M U X 16-BIT 30MHz ADC 16 D E M U X GREEN HIGH ORDER ADC OUT GREEN LOW ORDER ADC OUT 8 ADC OUT BLUE HIGH ORDER ADC OUT BLUE LOW ORDER ADC OUT BLUE CDS & PGA ADCLK SERIAL PORT SCLK SDATA LOAD POWER TIMING VSAMP BSAMP LCLMP 3 3 2 2 Ognd Avdd Agnd Ovdd Dvdd Dgnd Exar Corporation 48720 Kato Road, Fremont CA, 94538 • (510) 668-7000 • FAX (510) 668-7017 • www.exar.com xr XRD9836 16-BIT PIXEL GAIN AFE REV. 1.0.0 FIGURE 2. PIN OUT OF THE DEVICE ADCLK VSAMP BSAMP LCLMP IE SCLK SDIO LOAD Ovdd Ognd Avdd RED RED+ GRN GRN+ BLU BLU+ Agnd Rext Agnd Avdd CMREF CAPP CAPN 1 48 2 47 3 46 4 45 5 44 6 43 7 42 8 41 9 40 10 39 11 38 12 37 13 36 14 35 15 34 16 33 17 32 18 31 19 30 20 29 21 28 22 27 23 26 24 25 Dgnd Dvdd OGI [0] OGI [1] OGI [2] OGI [3] OGI [4] OGI [5] OGI [6] OGI [7] OGI [8] OGI [9] ADCO [0] ADCO [1] ADCO [2] ADCO [3] Ognd Ovdd ADCO [4] ADCO [5] ADCO [6] ADCO [7] Agnd Avdd TSSOP ORDERING INFORMATION PART NUMBER PACKAGE OPERATING TEMPERATURE RANGE XRD9836ACG 48 - TSSOP 0°C to +70°C 2 xr XRD9836 16-BIT PIXEL GAIN AFE REV. 1.0.0 PIN DESCRIPTIONS PIN # SYMBOL TYPE DESCRIPTION 1 ADCLK clock ADC clock - 50Kohm internal pull-down resistor 2 VSAMP clock Video Sample clock - 50Kohm internal pull-down resistor 3 BSAMP clock Black Sample clock - 50Kohm internal pull-down resistor 4 LCLMP clock Line Clamp clock 5 IE digital Input Enable - 50Kohm internal pull-down resistor 6 SCLK clock Serial Port serial clock - 50Kohm internal pull-down resistor 7 SDIO digital in/out 8 LOAD digital in 9 Ovdd power Output driver VDD 10 Ognd ground Output driver Ground 11 Avdd power ANALOG VDD 12 RED- analog RED ANALOG INPUT NEGATIVE 13 RED+ analog RED ANALOG INPUT POSITIVE 14 GRN- analog GREEN ANALOG INPUT NEGATIVE 15 GRN+ analog GREEN ANALOG INPUT POSITIVE 16 BLU- analog BLUE ANALOG INPUT NEGATIVE 17 BLU+ analog BLUE ANALOG INPUT POSITIVE 18 Agnd ground ANALOG GROUND 19 REXT analog External Bias Resistor -external 10Kohm resistor to ground 20 Agnd ground ANALOG GROUND 21 Avdd power ANALOG VDD 22 CMREF analog Common Mode Reference for ADC 23 CAPP analog ADC Reference By-Pass Serial Port Data I/O - 50Kohm internal pull-down resistor Serial Port Load - 50Kohm pull-down resistor 24 CAPN analog ADC Reference By-Pass 25 Avdd power ANALOG VDD 26 Agnd ground ANALOG GROUND 27 ADCO[7] output ADC parallel out 7 28 ADCO[6] output ADC parallel out 6 29 ADCO[5] output ADC parallel out 5 30 ADCO[4] output ADC parallel out 4 31 Ovdd power Output driver VDD 32 Ognd ground Output driver Ground 33 ADCO[3] output ADC parallel out 3 34 ADCO[2] output ADC parallel out 2 35 ADCO[1] output ADC parallel out 2 36 ADCO[0] output ADC parallel out 1 37 OGI[9] digital in OFFSET AND GAIN PARALLEL IN 9 (MSB) 38 OGI[8] digital in OFFSET AND GAIN PARALLEL IN 8 39 OGI[7] digital in OFFSET AND GAIN PARALLEL IN 7 40 OGI[6] digital in OFFSET AND GAIN PARALLEL IN 6 41 OGI[5] digital in OFFSET AND GAIN PARALLEL IN 5 42 OGI[4] digital in OFFSET AND GAIN PARALLEL IN 4 43 OGI[3] digital in OFFSET AND GAIN PARALLEL IN 3 44 OGI[2] digital in OFFSET AND GAIN PARALLEL IN 2 45 OGI[1] digital in OFFSET AND GAIN PARALLEL IN 1 46 OGI[0] digital in OFFSET AND GAIN PARALLEL IN 0 (LSB) 47 Dvdd power Digital VDD 48 Dgnd ground Digital Ground 3 (MSB) (LSB) xr XRD9836 16-BIT PIXEL GAIN AFE REV. 1.0.0 ELECTRICAL CHARACTERISTICS - XRD9836 Unless otherwise specified: AVDD=DVDD=3.3V, ADCLK = 30 MHz, REXT=10KΩ Ω, Ta=25C PARAMETER SYMBOL MIN. TYP. MAX. UNIT CONDITIONS A/D CONVERTER Resolution R 16 BITS Fc3 1.0 10 MSPS PER CHANNEL in 3-CH Mode Fc1 1.0 15 MSPS PER CHANNEL in 1-CH Mode Differential NonLinearity DNL -0.024 0.024 % FS Input Referred Offset ZSE 40 mV Offset Drift ZSD 15 uV/C Input Referred Gain Error FSE +/-2 %FS Gain Error Drift FSD 0.003 %FS/C Input Voltage Range IVR 2 Vpp PARAMETER SYMBOL Conversion Rate MIN. 0.002 TYP. MAX. UNIT VOLTAGE REFERENCES Vref+ CAPP 1.475 1.7 1.925 V Vref- CAPN 0.425 0.7 0.875 V Vref Common Mode VCMR 0.970 1.15 1.430 V Delta Vref Vref(+) - Vref(-) ∆VREF 0.85 1.00 1.15 V 4 CONDITIONS xr XRD9836 16-BIT PIXEL GAIN AFE REV. 1.0.0 ELECTRICAL CHARACTERISTICS - XRD9836 (con’t) Unless otherwise specified: AVDD=DVDD=3.3V, ADCLK = 30 MHz, REXT=10KΩ Ω, Ta=25C PARAMETER SYMBOL MIN. TYP. MAX. UNIT CONDITIONS 1.0 V 0.5 V 1.2 V CCD Mode, Gain = 1 to 10 CCD Mode, Gain = 2 to 20 CIS Mode, Gain = 0.5 to 5 8 40 nA 50 150 Ω CDS - S/H Input Voltage Range INVSR Input Leakage Current Iin Input Switch On Resistance Ron Input Switch Off Resistance Roff 100 Vclampccd 1.1 1.25 1.4 V CCD MODE Internal Voltage Clamp S/H Input (Non-inverting) Vclampsh -0.2 0.0 0.2 V CIS MODE PARAMETER SYMBOL MIN TYP MAX UNIT CONDITIONS Internal Voltage Clamp CDS Input (inverting) -40 MEGΩ At input pins: RED+/-, GRN+/-, BLU+/- when BSAMP is active guaranteed by design At input pins: RED+/-, GRN+/-, BLU+/- when BSAMP is inactive guaranteed by design OFFSET SPECIFICATIONS Fine Offset Range FOFRFOFR+ Fine Offset Step FOFRES Dynamic Offset Range DOFRDOFR+ Dynamic Offset Step DOFRES -200 80 -128 +127 -80 200 0.25 -125 120 mV mV mV -80 +160 -55 250 0.25 mV mV mV 5 10bit 10bit xr XRD9836 16-BIT PIXEL GAIN AFE REV. 1.0.0 ELECTRICAL CHARACTERISTICS - XRD9836 (con’t) Unless otherwise specified: AVDD=DVDD=3.3V, ADCLK = 30 MHz, REXT=10KΩ Ω, Ta=25C PARAMETER SYMBOL MIN. TYP. MAX. UNIT CONDITIONS PGA SPECIFICATIONS Gain Range Min. (Absolute Value) GRAN MIN 0.8 1.8 1.0 2.05 1.2 2.2 V/V Gain range = 1 to 10 Gain range = 2 to 20 Gain Range Max (Absolute Value) GRAN MAX 7.8 16 9.2 18.5 10.8 21 V/V Gain range = 1 to 10 Gain range = 2 to 20 Gain Resolution GRES V/V Gain range = 1 to 10 Gain range = 2 to 20 PARAMETER SYMBOL UNIT CONDITIONS 0.008 0.016 MIN. TYP. MAX. SYSTEM SPECIFICATIONS (INCLUDES CDS, PGA, AND A/D) Differential Non-Linearity DNL -0.024 0.002 +0.024 %FS GAIN =1.5 Integral Non-Linearity INL -2.4 +/- 0.1 2.4 %FS GAIN = 1.5 Input Referred Noise PGA Gain=1 IRNmin 1.7 mVrms GAIN = 1, inputs shorted together. Input Referred Noise PGA Gain=20 IRNmax 0.2 mVrms GAIN = 20, inputs shorted together. 6 xr XRD9836 16-BIT PIXEL GAIN AFE REV. 1.0.0 ELECTRICAL CHARACTERISTICS - XRD9836 (con’t) Unless otherwise specified: AVDD=DVDD=3.3V, ADCLK = 30 MHz, REXT=10KΩ Ω, Ta=25C PARAMETER SYMBOL MIN. TYP. MAX. UNIT CONDITIONS % % 3-CH, Figure 17 & Figure 19 1-CH, Figure 18 & Figure 20 CLOCK TIMING SPECIFICATIONS ADCLK Duty Cycle tadclk3 tadclk1 49 49 51 51 ADCLK period (1-Ch mode) tcp1 66.6 ns Figure 18 & Figure 20 ADCLK period (3-Ch mode) tcp3 33.3 ns Figure 17 & Figure 19 Single Channel Conversion period tcr1 66.6 ns Figure 18 & Figure 20 Three Channel Conversion period tcr3 100 ns Figure 17 & Figure 19 BSAMP Pulse Width tpwb 20 ns Figure 17 & Figure 19 VSAMP Pulse Width tpwv 20 ns Figure 17 & Figure 19 BSAMP sampling edge to VSAMP sampling edge tbvf ns Figure 17 & Figure 19 Min. Time negedge ADCLK to sampling VSAMP tvfcr ns Figure 17 & Figure 19 VSAMP/BSAMP Acquisition time (aperture delay) tap ns Figure 17 & Figure 19 Settling time tstl ns Figure 17 & Figure 19 Latency tlat cycles Figure 21 & Figure 22 50 12 6 15 9 7 xr XRD9836 16-BIT PIXEL GAIN AFE REV. 1.0.0 ELECTRICAL CHARACTERISTICS - XRD9836 (con’t) Unless otherwise specified: AVDD=DVDD=3.3V, ADCLK = 30 MHz, REXT=10KΩ Ω, Ta=25C PARAMETER SYMBOL MIN. TYP. MAX. UNIT CONDITIONS USIO TIMING SPECIFICATIONS uSIO Data Setup Time Tuss 10 ns Figure 15 & Figure 16 uSIO Data Hold Time Tush 10 ns Figure 15 & Figure 16 uSIO Load Setup Time Tusls 10 ns Figure 15 & Figure 16 uSIO Load Hold Time Tuslh 10 ns Figure 15 & Figure 16 uSIO Period Tusp 40 ns Figure 15 & Figure 16 uSIO Data Valid Delay Tusdvd PARAMETER SYMBOL 0 MIN. Figure 16 TYP. MAX. UNIT CONDITIONS Figure 4 I/O TIMING SPECIFICATIONS OGI Enable time Tev 8 ns VSAMP to ADC setup time Tva 4 ns ADC to OGI data setup time Togis ADC to OGI data hold time Togih ADCLK to ADCDO data out delay Tadcdo LCLMP Pulse duration LCLMPd 4 BSAMP/LCLMP setup BLs 1 ns BSAMP/LCLMP hold BLh 1 ns Figure 4 internal time adjustable 4 ns Figure 4 internal time adjustable 4 Figure 4 internal time adjustable 4 ns Figure 5 internal time adjustable 50 pixels 8 more pixels preferred xr XRD9836 16-BIT PIXEL GAIN AFE REV. 1.0.0 ELECTRICAL CHARACTERISTICS - XRD9836 (con’t) Unless otherwise specified: AVDD=DVDD=3.3V, ADCLK = 30 MHz, REXT=10KΩ Ω, Ta=25C PARAMETER SYMBOL MIN. TYP. MAX. UNIT CONDITIONS POWER SUPPLIES - 1 CHANNEL MODE Analog IDD IAVDD 47 mA Tested @ 3.6V Digital IDD IDVDD 5 mA Tested @ 3.6V Output IDD IOVDD 5 mA Tested @ 3.6V IDD Total IDD 57 mA Tested @ 3.6V Power Dissipation PDISS 188 mW Tested @ 3.6V PARAMETER SYMBOL UNIT CONDITIONS MIN. TYP. MAX. POWER SUPPLIES - 3 CHANNEL MODE Analog IDD IAVDD 60 84 110 mA Tested @ 3.6V Digital IDD IDVDD 1 9 15 mA Tested @ 3.6V Output IDD IOVDD 1 11 15 mA Tested @ 3.6V IDD Total IDD 62 104 140 mA Tested @ 3.6V Power Dissipation PDISS 220 343 500 mW Tested @ 3.6V Power Dissipation PDISS mW Tested @ 3.0V PARAMETER SYMBOL MAX. UNIT CONDITIONS 0.5 V 280 MIN. TYP. DIGITAL I/O Logic Input Low Vil Logic Input High Vih VDD-0.5 OGI Input Current High Iih -100 100 nA OGI Input Current Low Iil -100 100 nA Control Inputs Current High Iinh 50 90 150 uA 50Kohm Pull down Control Inputs Current Low Iinl -5 0.1 5 uA 50Kohm Pull down Logic Output Low Vol 0.5 V Isink=2.0mA Logic Output High Voh VDD-0.5 V Isrc=2.0ma Tristate Leakage IOLeak -100 V 0.1 9 100 nA xr XRD9836 16-BIT PIXEL GAIN AFE REV. 1.0.0 VSAMP BSAMP LCLMP SERIAL PORT SCLK SDATA LOAD BLUE GAIN REGISTER BLUE OFFSET REGISTER 10 Blue Gain 10 Blue Offset BLUE CDS & PGA GREEN CDS & 10 Green Offset PGA Green Gain 10 Red Offset 10 Red Gain 10 ADCLK FIGURE 3. SYSTEM BLOCK DIAGRAM 10 ADCLK (30MHz) Blue Offset 10 Blue Gain 10 OFFSET GAIN INPUT 10 Green Offset 10 Green Gain 10 Red Offset Red Gain DSP ASIC A three-pin, Micro-controller Serial I/O link (uSIO) is used to write or read from the XRD9836’s internal configuration registers. The internal registers control the various modes of operation of the chip. 10 10 IE For ADC outputs, the XRD9836 has an 8-bit parallel bus ADC Data Out (ADCDO). The ADC output data is transmitted sequentially in the following order for 3-ch mode red high order byte, red low order byte, green high order byte, green low order byte, blue high order byte, blue low order byte as shown in Figure 5 GREEN GAIN REGISTER GREEN OFFSET REGISTER The Input Enable pin (IE) enables OGI port to program internal pixel gain and offset registers. If IE goes low, the gain and offset registers will store the last data while IE was high. RED GAIN REGISTER RED OFFSET REGISTER XRD9836 AFE R E D + R E D - G R N + G R N - RED CDS & PGA B L U + B L U - M U X A 10-bit parallel bus Offset Gain Input Port (OGI) is used to transfer 10 bits of Gain and 10 bits of Offset. In the 3-channel mode, the data is received sequentially in the following order: red gain, red offset, green gain, green offset, blue gain, blue offset. In 1-channel mode, the data is received sequentially gain then offset. For an example of both 3-channel and 1-channel OGI timing see Figure 4. TIMING 16-BIT 16 30MHZ ADC C A P P C A P N BIAS C M R E F R E X T D E M U X 3 A v d d 3 A g n d D v d d D g n d 2 O v d d BLUE HIGH ORDER ADC OUT BLUE LOW ORDER ADC OUT GREEN HIGH ORDER ADC OUT GREEN LOW ORDER ADC OUT RED HIGH ORDER ADC OUT RED LOW ORDER ADC OUT 2 O g n d 8 The XRD9836 provides a 16-bit Analog Front End functionality for Mid-to-High range, next-generation scanner applications. It has 3 channels of Correlated Double Sampling (CDS), using a 10-bit Dynamic Offset DAC, a 10-bit Programmable Gain Amplifier (PGA) and a 10-bit Fine Offset DAC for Red, Green, and Blue CCD signals. A 16-bit 30MHz ADC is multiplexed among these 3 channels to provide digitized image data for the scanner ASIC chip. In 3-channel mode, the order of channels is R, G, B. In the 1-channel mode, only the selected channel is active. The XRD9836 provides one of the key requirements for the next generation scanner AFE’s, the ability to control Pixel-by-Pixel Gain and Offset values. Figure 3 shows the ASIC and AFE interface for the proposed system. ADC OUT SYSTEM OVERVIEW xr XRD9836 16-BIT PIXEL GAIN AFE REV. 1.0.0 GAIN SELECT: also reminded that data coming out of the ADC outputs will have latency from the gain and offset provided (10 ADC cycles for single color and 12 cycles for 3-color). This latency includes the cycles to put the gain and offset data into the registers and the latency of the ADC itself (9 ADCLK cycles). The XRD9836’s Gain range is selectable to either 1 to 10 or 2 to 20 with the Gain Select Bit. If Gain of 1 to 10 is selected (Gain Select bit = 0), the maximum input is 1.0V. If Gain of 2 to 20 is selected (Gain Select bit = 1), the maximum input is 0.5V. Sampling of the OGI parallel input port is defined as the red gain data being the first pulse of ADCLK after VSAMP, therefor VSAMP must occur before a rising edge of ADCLK. It is also recommended that VSAMP__OGI_DLY (DelayD[7:4]) should be smaller than OGI_DLY (DelayA[7:4]) to make sure the correct data is sampled, and that relationship is not reversed internally. PARALLEL PORT FOR PIXEL OFFSET AND GAIN CONTROL (OGI): The timing diagram in Figure 4 shows the Offset and Gain Inputs (OGI) and ADCLK in relationship to VSAMP. 3 - Channel OGI Timing PARALLEL PORT FOR ADC OUTPUT (ADCDO): Tev IE Tva VSAMP The timing diagram, Figure 5, shows the ADC output (ADCDO). The XRD9836 will be clocking ADC high order bytes on the rising edge of ADCLK and clocking ADC low order bytes on the falling edge of ADCLK. As noted the RGB data is synchronized to sampling edge of VSAMP. ADCLK OGI 10-bit parallel input RG RO Togis GG GO BG BO RG Togih 1 - Channel OGI Timing Tev IE Tva VSAMP 3 - Channel ADCDO Timing ADCLK OGI 10-bit parallel input VSAMP Gain Offset Togis Gain ADCLK Togih ADCDO 8-bit parallel output FIGURE 4. OGI TIMING (ADCLKPOL=0, VSAMPPOL=0) BDL RDH RDL GDH GDL BDH BDL Tadcdo 1 - Channel ADCDO Timing The ASIC chip will be clocking OGI data at six times the pixel rate clock in 3-CH mode and two times the pixel rate in 1-CH mode. The gain data is grabbed on the rising edge of ADCLK and the offset data on the falling edge of ADCLK. The OGI port is read into internal pixel gain and offset registers only when Input Enable (IE) is active before the sampling edge of VSAMP as shown above. As noted the RGB gain/offset data is synchronized to sampling edge of VSAMP. Note that ADCLK frequency is 3X the pixel rate in 3CH mode and 1X the pixel rate in 1-CH mode. The ADCLK’s duty cycle is required to be 50%. It is assumed that the OGI port and ADCLK input have matched output drivers inside the ASIC, matched trace lengths on the PCB between the ASIC and the XRD9836, and matched delays at input buffers inside the XRD9836 in order to receive OGI data on both edges of ADCLK error free. VSAMP ADCLK ADCDO 8-bit parallel output DH DL Tadcdo FIGURE 5. ADCDO TIMING (ADCLKPOL=0, VSAMPPOL=0) PIXEL GAIN/OFFSET CONTROL (FGOM OR PGOM): Figure 6 shows the block diagram of the CDS/PGA/ Offset DACs/ADC signal path. The offset for each channel is controlled by a 10-bit Dynamic offset DAC before the CDS amplifier and a 10-bit Fine offset DAC after the PGA amplifier. Thus, the total offset of each channel is controlled by two 10-bit offset DACs. The Dynamic offset DAC will have a range of -80mV to +160mV, with the ability to adjust the CDS stage offset to within +/- 0.25mV. The Fine offset DAC will The latency between the input of the parallel inputs and their effective application is 1 pixel. The user is 11 xr XRD9836 16-BIT PIXEL GAIN AFE REV. 1.0.0 have a range of +/- 128mV, with the ability to adjust PGA offsets to within +/- 0.25mV. There are two modes of operation for Pixel Gain and Offset control. The first is a fixed gain and offset control mode where the gain and offset is adjusted once per line or per scan. The second mode is a pixel to pixel adjustment of gain and offset. This mode allows for gain and offset adjustment for each and every pixel. These modes are controlled by bit D0, GOM (Gain Offset Mode), in the MODE register. OB Pixels VBlack VVideo FIGURE 7. CCD WAVEFORM - DEFINITION OF TERMS CCD OUTPUT INFORMATION = (VBLACK-VVIDEO) LCLMP TIMING: In PPGOM (pixel-by-pixel gain and offset mode, GOM=1), the user can input 10 bits of Gain and 10 bits of Dynamic offset data through the OGI port. In order to reject higher frequency power supply noise which is not attenuated near the sampling frequency, the XRD9836 utilizes a fully differential input structure. Since the CDS process uses AC coupled inputs, the coupling capacitor must be charged to the common-mode range of the analog front-end. This can be accomplished by clamping the coupling capacitor to the internal clamp voltage when the CCD is at a reference level at the beginning of each line using LCLMP. This needs to be done for enough clamping time (Tclamp) which is determined by external Capacitor, internal switch resistance, BSAMP pulse width and number of samples during line clamp. The maximum capacitance is NC CDS + PGA 10 Bit + 3:1 MUX Dynamic Offset DAC 10 BIT V Black CCD Waveform In FGOM (Fixed Gain/Offset Mode, GOM=0), the user can program the PGA gain, Dynamic and Fine Offset registers through the micro-controller serial interface (uSIO). CDS Signal Active Pixels VDark ADC Fine Offset DAC 10 BIT FIGURE 6. CDS TO ADC SIGNAL PATH CM A X = CCD MODE(CORRELATED DOUBLE SAMPLING): Correlated double sampling is a technique used to level shift and acquire CCD output signals whose information is equal to the difference between consecutive reference (VBlack) and signal (VVideo) samples. The CDS process consists of three steps: where N * tp w b ( Rc + R s ) * ln ( V rV-eV c) tpwb = clamp pulse width (BSAMP typ 25ns) N = number of pixels used for clamping Rc = clamp resistance (typ 50ohms) 1) Sampling and holding the reference black level (VBlack). Rs = signal source resistance (typ 50ohms) 2) Sampling the video level (VVideo). Vc = clamp voltage (1.2V) 3) Subtracting the two samples to extract the video information. (CCD signal information = VBlack- VVideo) Ve = error voltage (3.05uV worst case) Vr = black level The clamp LCLMP should be active for at least 4 pixels during Optical Black (OB) and should be inactive during all of the Active portion of the line. Usually OB lasts for 40 - 50 pixels. It is better if LCLMP remains active during as much of OB as possible. LCLMP should be set Active 1ns before BSAMP leading edge and should be held for at least 1ns after BSAMP trailing edge. Once the CCD signal information has been extracted, it can be processed further through amplification and/ or offset adjustment. Since system noise is also stored and subtracted during the CDS process, signals with bandwidths less than half the sampling frequency will be substantially attenuated. 12 xr XRD9836 16-BIT PIXEL GAIN AFE REV. 1.0.0 4. VSAMP should have typ > 25ns pulse width. In addition to the above requirement for LCLMP on a line by line basis there is an additional requirement for a one time LCLMP upon power-up to provide the AC coupling capacitor’s initial charge. The one time LCLMP pulse width can also be determined from the Cmax equation above. A typical value, using 1 nf cap, with initial charge of 3V (Vr - Vc), and a BSAMP pulse width of 25ns, is estimated to be 1.4us. This is equivalent to one time LCLMP of 56 OB pixels upon power up. 5. LCLMP is not needed for CIS Applications. (except for APOAM even and odd selection) 6. Input Voltage Range: Vcm @ Vin- = 0 to 1.4 V CIS Signal @ Vin+ = 0 to 1.2 V above Vcm offset CIS Signal 3-CHANNEL CDS MODE: Vcm (DCoffset) This mode allows simultaneous CDS of the red, green and blue inputs. Black-level sampling occurs on each pixel and is equal to the width of the BSAMP sampling input. The black level is held on the sampling edge of BSAMP and the PGA will immediately begin to track the signal input until the sampling edge of VSAMP. NC CDS + PGA 10 bit + Dynamic Offset DAC 10 bit 3:1 MUX ADC Fine Offset DAC 10 bit At the end of the video sampling phase, the difference between the reference and video levels is inverted, amplified, and offset depending on the contents of the PGA gain and offset registers. The RGB channels are then sequentially converted by a high-speed A/D converter. Converted data appears on the data output bus after 9 ADCLK cycles. The red channel is synchronized on the rising edge of the first ADCLK after the sampling edge of VSAMP. The power-up default mode is for CDS sampling a CCD input. FIGURE 8. CIS SIGNAL PATH 1-CHANNEL CDS MODE: FIGURE 9. CIS WAVEFORM -DEFINITION OF TERMS Pixel N-1 Pixel N Pixel N+1 Pixel N+2 Pixel N+3 C IS W aveform INVSR Vcm The 1-Channel CDS mode allows high-speed acquisition and processing of a single channel. The timing, clamp and buffer configurations are similar to the 3channel mode described previously. To select a single channel input, the color bits of configuration selected by CHAN[1:0] bits, in the MODE register, must be set to the appropriate value. The A/D input will begin to track the selected color input on the next positive edge of ADCLK. If the configuration is toggled from a single color mode to 3-channel mode, RGB scanning will not occur until the circuit is re-synchronized on the sampling edge of VSAMP. 3-CHANNEL CIS AND S/H MODE The XRD9836 also supports operation for Contact Image Sensor (CIS) and S/H applications. The red channel is synchronized on the rising edge of the first ADCLK after the sampling edge of VSAMP. In this mode of operation, the BSAMP input is connected to DGND, and input sampling occurs on the falling edge of VSAMP(VSAMP_POL=0). 1-CHANNEL CIS AND S/H MODE: The 1-channel CIS S/H mode allows high-speed acquisition and processing of a single channel. The timing, clamp and buffer configurations are similar to the 3-channel mode. In single channel mode one color channel is selected using CHAN[1:0]. If the configuration is toggled from single color to 3-channel mode, RGB scanning will not occur until the circuit is re-synchronized by the first sampling edge of VSAMP. CIS MODE: The AFE can be configured for inputs from a CCD or a CIS type device by setting the CCD_CIS bit. For CIS mode, the following interface features are provided: 1. DC Coupled Inputs. 2. Gain Range is 0.5 to 5 with 10 bit resolution. 3. It is assumed that CIS Sample and Hold Outputs and DC offset buffer have low output impedances(~50 ohms). 13 xr XRD9836 16-BIT PIXEL GAIN AFE REV. 1.0.0 TIMING - CLOCK BASICS: XRD9836 has included a programmable delay function to help simplify this job. The XRD9836 has 4 clock signals BSAMP, VSAMP, ADCLK and LCLMP. These inputs control the sampling, clamping and synchronization functions of the device. There are four serial interface registers, DelayA, DelayB, DelayC and DelayD, used to program various delays of the pixel timing and Data and OGI bus timing. Each register is divided into 2 delay parameters. Each delay parameter is 4 bits wide. The pixel rate clocks are BSAMP, VSAMP and ADCLK. BSAMP controls the sampling of the black reference level of a CCD input signal. VSAMP controls the sampling of the video level of a CCD or CIS output signal. The ADCLK controls the internal sampling of the PGA by the ADC and ADC operation. DelayA[7:4] controls the OGI sampling delay. These bits program the delay of the ADCLK used to sample the OGI input bus. Delay is added in 1ns increments. See Figure 12. DelayA[3:0] controls the ADCDO delay. These bits are used to program the timing delay added to the ADCDO data bus updates. Delay is added in 1ns increments. See Figure 11. The line rate clock, LCLMP, performs the clamping and synchronization functions. The clamp function sets the bias point for the external AC coupling capacitor on the inputs. Synchronization defines the odd pixel in the APOAM mode. DelayB[7:4] controls the amount of delay added to the leading edge of BSAMP. Delay to the leading edge will be added in 0.5ns increments. This can help to position the leading edge of the internal BSAMP away from the reset pulse of the CCD input. See Figure 11. CLOCK POLARITY Each of the 4 timing signals has a separate polarity control bit in the CONTROL register. Figure 10 shows the logic implementation of the polarity control. If the polarity bit is low (default) BSAMP and VSAMP sample on the falling edge, LCLMP is active high and ADCLK must be low during the VSAMP falling edge. See timing examples if Figure 17 and Figure 18 DelayB[3:0] controls the amount of delay added to the trailing edge of BSAMP. Delay to the trailing edge will be added in 0.5ns increments. This will allow for adjustment of the Black Level sampling position by the internal BSAMP. See Figure 11. If any of the external timing signals are inverted from the default timing simply write a “1” to the appropriate polarity bit to compensate. BSAMP Polarity VSAMP Polarity ADCLK Polarity DelayC[7:4] controls the amount of delay added to the leading edge of VSAMP. Delay will be added in 0.5ns increments. This can help to position the leading edge of the internal VSAMP to track the video portion of the CCD input. See Figure 11. DelayC[3:0] controls the amount of delay added to the trailing edge of VSAMP. Delay will be added in 0.5ns increments. This will allow for adjustment of the Video Level sampling position by the internal VSAMP. See Figure 11. AFE Delays Clock Logic DelayD[7:4] controls the amount of delay added to the VSAMP OGI. The internal VSAMP_OGI is used to transfer the input OGI register data to the PGA and OFFSET control. Delay is added in 1ns increments. Please note the falling edge of the internal VSAMP_OGI must occur before the rising edge of the OGI sampling clock. See Figure 12. ADC OGI LCLMP Polarity FIGURE 10. CLOCK POLARITY AND DELAYS DELAY CONTROL One of the more difficult tasks in designing a scanner is optimizing the pixel and interface (data output & OGI) timing for a CCD, CDS and ADC. The DelayD[3:0] controls the amount of delay added to the ADCLK. Delay is added to the internal ADCLK in 0.5ns increments. See Figure 11. 14 xr XRD9836 16-BIT PIXEL GAIN AFE REV. 1.0.0 tPIX Black Sample Point CCD Signal tBK Video Sample Point tVD DelayB[7:4] BSAMP DelayB[3:0] internal BSAMP VSAMP DelayC[3:0] internal VSAMP DelayC[7:4] ADCLK DelayD[3:0] DelayD[3:0] internal ADCLK ADCDO Output Bus Tadcdo DelayA[3:0] FIGURE 11. PIXEL TIMING & ADCDO (OUTPUT DATA) DELAY ADJUSTMENT Pixel (n-1) Pixel (n) tPIX Black Sample Point CCD Signal Video Sample Point OGI Input Bus Gain (n) Offset (n) Togis Gain (n+1) OGI Gain Sample Point Togih VSAMP DelayD[7:4] internal OGI VSAMP DelayD[7:4] ADCLK DelayA[7:4] DelayA[7:4] internal OGI sample delay FIGURE 12. OGI TIMING DELAY ADJUSTMENT 15 Offset (n+1) OGI Offset Sample Point xr XRD9836 16-BIT PIXEL GAIN AFE REV. 1.0.0 ALTERNATE PIXEL OFFSET ADJUST MODE (APOAM): In the PPGOM mode, the APOAM can be selected only when Input Enable (IE) is disabled. The last dynamic gain and offset programmed using the OGI port are used for the odd pixels. In some applications, alternate pixels along a scan line come from two different rows of CCD’s, causing a systematic offset between alternate pixels. When the XRD9836 is operated in the Fixed Gain Offset Mode (FGOM), it does not have the ability to compensate for this alternating offset phenomenon. The APOAM dynamic offset and the APOAM fine register values, programmed through the USIO port are used for the even pixels. The gain value is fixed as the last received value through the serial port. This is shown in Figure 14. To compensate for these offsets, this chip has an Alternate Pixel Offset Adjust mode (APOAM), which can be enabled by writing a 1 to the APOAM bit (D1of the MODE register) through the serial port. In APOAM mode each channel has four 10-bit offset registers to control offset. Odd pixel offsets are compensated for by the Dynamic Offset Register value and the Fine Offset Register value. The even pixel offsets are compensated for by the APOAM Dynamic Offset Register value and the APOAM Fine Offset Register value. The individual channel pixel gains do not change and are determined by the red, green and blue PGA gain register settings. SUMMARY OF APOAM USABILITY: MODE IE APOAM FIXED GAIN/OFFSET OFF USABLE FIXED GAIN/OFFSET ON USABLE PIXEL GAIN/OFFSET OFF USABLE PIXEL GAIN/OFFSET ON NOT USABLE TABLE 1: SUMMARY OF APOAM USABILITY NC CDS Signal CDS + PGA 10 Bit 3:1 MUX LCLMP ADC + APOAM Dyn. Reg. Fine Offset DAC 10 BIT Dyn. Reg. Dynamic Offset DAC 10 BIT VSAMP Fine Reg. APOAM Fine Reg. FIGURE 13. APOAM MODE - CONFIGURATION OF OFFSET REGISTERS DYNAMIC OFFSET ODD EVEN ODD EVEN FINE OFFSET ODD EVEN ODD EVEN Figure 14. APOAM SYNCHRONIZATION AND REGISTER ALTERNATION The offset alternates every other pixel. The first pixel and all odd pixels in the line use the dynamic offset and fine offset register values. The even pixels use the APOAM dynamic offset and the APOAM fine offset register values. Odd pixels are defined from the first ADCLK after the fall of LCLMP. Note: LCLMP also defines which pixel is even or odd. The first pixel after LCLMP goes inactive is odd. Position LCLMP so that there are an even number of pixels before start of active pixels. 16 xr XRD9836 16-BIT PIXEL GAIN AFE REV. 1.0.0 MICRO-CONTROLLER SERIAL PORT FOR MODE CONTROL (USIO): XRD9836 the SDIO pin stays configured as an input for entire 18 SCLK's before LOAD goes high. The E0 and E1 bits are dummy (unused) bits. The uSIO is a bidirectional I/O port which is used for configuring various operating modes as well as phase aligning internal clocks (delay control). The serial port can be used to program any of the registers listed in the registers table. Note that SDIO is a bidirectional pin used to read or write the XRD9836 internal registers. The R/W bit will define the direction of the bus after Address bits. If R/W = 0, a write to the XRD9836 is performed. If R/W = 1, a read of the XRD9836’s internal registers is performed. For a read of the XRD9836 internal registers (R/W=1) the E0 and E1 are used as a transition time for the SDIO pin going from an input to a output. During this time SDIO pin is tri-stated. SDIO is an input while serial port accepts the address of the register to be read and during the E0 and E1 time period transitions to an output for the read operation. During a read operation the first 18 positive edges are used. If there are less than 18, not all of the data will be output. If there are more than 18, only the first 18 bits will be valid. The data becomes valid after the rising edge of SCLK. During a write operation there must be 18 positive edges of SCLK between the fall of LOAD and the rise of LOAD. If there are more or less than 18, the write operation will not take place. For a write to the Tusls Tuslh Tusp Tuss Tush LOAD SCLK msb SDIO R/W A4 Write lsb A3 A2 A1 A0 msb E1 E0 lsb D9 D8 D7 D6 Dummy bits Register Address SDIO configured as D5 D4 D3 D2 D1 D0 Write Register Data Input FIGURE 15. SERIAL PORT WRITE TIMING (R/W=0) Tusls Tuslh Tusp Tuss Tusdvd Tush LOAD SCLK R/W Read SDIO configured as A4 msb lsb msb SDIO A3 A2 A1 Register Address Input A0 E1 lsb D9 E0 Dummy bits D8 D7 D6 D5 D4 D3 Read Register Data Tri-state Output FIGURE 16. SERIAL PORT READ TIMING (R/W=1) 17 D2 D1 D0 xr XRD9836 16-BIT PIXEL GAIN AFE REV. 1.0.0 REGISTERS DATA BITS ADDRESS A 4 0 A 3 0 A 2 0 A 1 0 A 0 0 0 0 0 0 0 0 0 0 0 0 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 RPGA [9] RPGA [8] RPGA [7] RPGA [6] RPGA [5] RPGA [4] RPGA [3] RPGA [2] RPGA [1] RPGA [0] 1 GPGA [9] GPGA [8] GPGA [7] GPGA [6] GPGA [5] GPGA [4] GPGA [3] GPGA [2] GPGA [1] GPGA [0] 1 0 BPGA [9] BPGA [8] BPGA [7] BPGA [6] BPGA [5] BPGA [4] BPGA [3] BPGA [2] BPGA [1] BPGA [0] 0 1 1 RDOFF [9] RDOFF [8] RDOFF [7] RDOFF [6] RDOFF [5] RDOFF [4] RDOFF [3] RDOFF [2] RDOFF [1] RDOFF [0] 0 1 0 0 GDOFF [9] GDOFF [8] GDOFF [7] GDOFF [6] GDOFF [5] GDOFF [4] GDOFF [3] GDOFF [2] GDOFF [1] GDOFF [0] 0 0 1 0 1 BDOFF [9] BDOFF [8] BDOFF [7] BDOFF [6] BDOFF [5] BDOFF [4] BDOFF [3] BDOFF [2] BDOFF [1] BDOFF [0] 0 0 1 1 0 RFOFF [9] RF0FF [8] RFOFF [7] RF0FF [6] RFOFF [5] RFOFF [4] RFOFF [3] RFOFF [2] RFOFF [1] RFOFF [0] 0 0 1 1 1 GFOFF [9] GF0FF [8] GFOFF [7] GF0FF [6] GFOFF [5] GFOFF [4] GFOFF [3] GFOFF [2] GFOFF [1] GFOFF [0] 0 1 0 0 0 BFOFF [9] BF0FF [8] BFOFF [7] BF0FF [6] BFOFF [5] BFOFF [4] BFOFF [3] BFOFF [2] BFOFF [1] BFOFF [0] 0 1 0 0 1 ARDOF [9] ARDOF [8] ARDOF [7] ARDOF [6] ARDOF [5] ARDOF [4] ARDOF [3] ARDOF [2] ARDOF [1] ARDOF [0] 0 1 0 1 0 AGDOF [9] AGDOF [8] AGDOF [7] AGDOF [6] AGDOF [5] AGDOF [4] AGDOF [3] AGDOF [2] AGDOF [1] AGDOF [0] 0 1 0 1 1 ABDOF [9] ABDOF [8] ABDOF [7] ABDOF [6] ABDOF [5] ABDOF [4] ABDOF [3] ABDOF [2] ABDOF [1] ABDOF [0] 0 1 1 0 0 ARFOF [9] ARFOF [8] ARFOF [7] ARFOF [6] ARFOF [5] ARFOF [4] ARFOF [3] ARFOF [2] ARFOF [1] ARFOF [0] 0 1 1 0 1 AGFOF [9] AGFOF [8] AGFOF [7] AGFOF [6] AGFOF [5] AGFOF [4] AGFOF [3] AGFOF [2] AGFOF [1] AGFOF [0] 0 1 1 1 0 ABFOF [9] ABFOF [8] ABFOF [7] ABFOF [6] ABFOF [5] ABFOF [4] ABFOF [3] ABFOF [2] ABFOF [1] ABFOF [0] 0 1 1 1 1 0 0 0 VSAMP POL DelayA [4] DLP Disable DelayA [3] RESET 0 BSAMP POL DelayA [5] OEB 1 LCLMP POL DelayA [6] PwrDwn DELAY A ADC POL DelayA [7] DelayA [2] DelayA [1] DelayA [0] DELAY B 1 0 0 0 1 DELAY C 1 0 0 1 0 DelayB [7] DelayC [7] DelayB [6] DelayC [6] DelayB [5] DelayC [5] DelayB [4] DelayC [4] DelayB [3] DelayC [3] DelayB [2] DelayC [2] DelayB [1] DelayC [1] DelayB [0] DelayC [0] DELAY D 1 0 0 1 1 MODE 1 0 1 0 0 DelayD [7] NOFS2 1 0 1 DelayD [2] CHAN [0] do not change DelayD [0] GOM 0 DelayD [3] CHAN [1] do not change DelayD [1] APOAM 1 DelayD [5] GAIN SELECT do not change DelayD [4] CCD/CIS TEST DelayD [6] TEST ENABLE do not change do not change do not change RED PGA GREEN PGA BLUE PGA RED DYNAMIC OFFSET GREEN DYNAMIC OFFSET BLUE DYNAMIC OFFSET RED FINE OFFSET GREEN FINE OFFSET BLUE FINE OFFSET APOAM RED DYNAMIC OFFSET APOAM GREEN DYNAMIC OFFSET APOAM BLUE DYNAMIC OFFSET APOAM RED FINE OFFSET APOAM GREEN FINE OFFSET APOAM BLUE FINE OFFSET CNTRL/POL do not change do not change do not change Table 2: NOTE: Note: Shaded cells represent unused bits 18 do not change xr XRD9836 16-BIT PIXEL GAIN AFE REV. 1.0.0 Red PGA Register D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 RPGA (00000) RPGA [9] RPGA [8] RPGA [7] RPGA [6] RPGA [5] RPGA [4] RPGA [3] RPGA [2] RPGA [1] RPGA [0] default 0 0 0 0 0 0 0 0 0 0 RPGA[9:0] is used to set the gain of the Programmable Gain Amplifier (PGA) for the red channel. Code = 0000000000 is minimum gain. Code = 1111111111 is maximum gain. Green PGA Register D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 GPGA (00001) GPGA [9] GPGA [8] GPGA [7] GPGA [6] GPGA [5] GPGA [4] GPGA [3] GPGA [2] GPGA [1] GPGA [0] default 0 0 0 0 0 0 0 0 0 0 GPGA[9:0] is used to set the gain of the Programmable Gain Amplifier (PGA) for the green channel. Code = 0000000000 is minimum gain. Code = 1111111111 is maximum gain. Blue PGA Register D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 BPGA (00010) BPGA [9] BPGA [8] BPGA [7] BPGA [6] BPGA [5] BPGA [4] BPGA [3] BPGA [2] BPGA [1] BPGA [0] default 0 0 0 0 0 0 0 0 0 0 BPGA[9:0] sets the gain of the Programmable Gain Amplifier (PGA) for the blue channel. Code = 0000000000 is minimum gain. Code = 1111111111 is maximum gain. Red Dynamic Offset Register RDOFF (00011) default D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 RDOFF [9] RDOFF [8] RDOFF [7] RDOFF [6] RDOFF [5] RDOFF [4] RDOFF [3] RDOFF [2] RDOFF [1] RDOFF [0] 0 1 0 1 0 1 0 1 0 1 RDOFF[9:0] sets the course offset level prior to the PGA of the Red channel. Code = 0000000000 is -80mV. Code =1111111111 is +160mV. Default is Code 0101010101 = 0 mV. 19 xr XRD9836 16-BIT PIXEL GAIN AFE REV. 1.0.0 Green Dynamic Offset Register D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 GDOFF (00100) GDOFF [9] GDOFF [8] GDOFF [7] GDOFF [6] GDOFF [5] GDOFF [4] GDOFF [3] GDOFF [2] GDOFF [1] GDOFF [0] default 0 1 0 1 0 1 0 1 0 1 GDOFF[9:0] sets the course offset level prior to the PGA of the Green channel. Code = 0000000000 is -80mV. Code =1111111111 is +160mV. Default is Code 0101010101 = 0 mV. Blue Dynamic Offset Register D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 BDOFF (00101) BDOFF [9] BDOFF [8] BDOFF [7] BDOFF [6] BDOFF [5] BDOFF [4] BDOFF [3] BDOFF [2] BDOFF [1] BDOFF [0] default 0 1 0 1 0 1 0 1 0 1 BDOFF[9:0] sets the course offset level prior to the PGA of the Blue channel. Code = 0000000000 is -80mV. Code =1111111111 is +160mV. Default is Code 0101010101 = 0 mV. Red Fine Offset Register D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 RFOFF (00110) RFOFF [9] RF0FF [8] RFOFF [7] RF0FF [6] RFOFF [5] RFOFF [4] RFOFF [3] RFOFF [2] RFOFF [1] RFOFF [0] default 1 0 0 0 0 0 0 0 0 0 RFOFF[9:0] sets the fine offset level after the PGA in the Red channel. Code = 0000000000 is -128mV. Code =1111111111 is +128mV. Default is Code 1000000000 = 0 mV. Green Fine Offset Register D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 GFOFF (00111) GFOFF [9] GFOFF [8] GFOFF [7] GFOFF [6] GFOFF [5] GFOFF [4] GFOFF [3] GFOFF [2] GFOFF [1] GFOFF [0] default 1 0 0 0 0 0 0 0 0 0 GFOFF[9:0] sets the fine offset level after the PGA in the Green channel. Code = 0000000000 is -128mV. Code =1111111111 is +128mV. Default is Code 1000000000 = 0 mV. 20 xr XRD9836 16-BIT PIXEL GAIN AFE REV. 1.0.0 Blue Fine Offset Register D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 BFOFF (01000) BF0FF [9] BFOFF [8] BFOFF [7] BF0FF [6] BFOFF [5] BFOFF [4] BFOFF [3] BFOFF [2] BFOFF [1] BFOFF [0] default 1 0 0 0 0 0 0 0 0 0 BFOFF[9:0] sets the fine offset level after the PGA in the Blue channel. Code = 0000000000 is -128mV. Code =1111111111 is +128mV. Default is Code 1000000000 = 0 mV. APOAM Red Dynamic Offset Register D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 ARDOF (01001) ARDOF [9] ARDOF [8] ARDOF [7] ARDOF [6] ARDOF [5] ARDOF [4] ARDOF [3] ARDOF [2] ARDOF [1] ARDOF [0] default 0 1 0 1 0 1 0 1 0 1 RDOFF[9:0] sets the course offset level prior to the PGA of the Red channel for even pixels in APOAM Mode. Code = 0000000000 is -80mV. Code =1111111111 is +160mV. Default is Code 0101010101 = 0 mV. APOAM Green Dynamic Offset Register AGDOF (01010) default D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 AGDOF [9] AGDOF [8] AGDOF [7] AGDOF [6] AGDOF [5] AGDOF [4] AGDOF [3] AGDOF [2] AGDOF [1] AGDOF [0] 0 1 0 1 0 1 0 1 0 1 GDOFF[9:0] sets the course offset level prior to the PGA of the Green channel for even pixels in APOAM Mode. Code = 0000000000 is -80mV. Code =1111111111 is +160mV. Default is Code 0101010101 = 0 mV. APOAM Blue Dynamic Offset Register D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 ABDOF (01011) ABDOF [9] ABDOF [8] ABDOF [7] ABDOF [6] ABDOF [5] ABDOF [4] ABDOF [3] ABDOF [2] ABDOF [1] ABDOF [0] default 0 1 0 1 0 1 0 1 0 1 BDOFF[9:0] sets the course offset level prior to the PGA of the Blue channel for even pixels in APOAM Mode. Code = 0000000000 is -80mV. Code =1111111111 is +160mV. Default is Code 0101010101 = 0 mV. 21 xr XRD9836 16-BIT PIXEL GAIN AFE REV. 1.0.0 APOAM Red Fine Offset Register D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 ARFOF (01100) ARFOF [9] ARFOF [8] ARFOF [7] ARFOF [6] ARFOF [5] ARFOF [4] ARFOF [3] ARFOF [2] ARFOF [1] ARFOF [0] default 1 0 0 0 0 0 0 0 0 0 RFOFF[9:0] sets the fine offset level after the PGA of the Red channel for even pixels in APOAM Mode. The offset is adjusted in 1mV increments. Code = 0000000000 is -128mV. Code =1111111111 is +128mV. Default is Code 1000000000 = 0 mV. APOAM Green Fine Offset Register D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 AGFOF (01101) AGFOF [9] AGFOF [8] AGFOF [7] AGFOF [6] AGFOF [5] AGFOF [4] AGFOF [3] AGFOF [2] AGFOF [1] AGFOF [0] default 1 0 0 0 0 0 0 0 0 0 GFOFF[9:0] sets the fine offset level after the PGA of the Green channel for even pixels in APOAM Mode. The offset is adjusted in 1mV increments. Code = 0000000000 is -128mV. Code =1111111111 is +128mV. Default is Code 1000000000 = 0 mV. APOAM Blue Fine Offset Register D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 ABFOF (01110) ABFOF [9] ABFOF [8] ABFOF [7] ABFOF [6] ABFOF [5] ABFOF [4] ABFOF [3] ABFOF [2] ABFOF [1] ABFOF [0] default 1 0 0 0 0 0 0 0 0 0 BFOFF[9:0] sets the fine offset level after the PGA of the Blue channel for even pixels in APOAM Mode. The offset is adjusted in 1mV increments. Code = 0000000000 is -128mV. Code =1111111111 is +128mV. Default is Code 1000000000 = 0 mV. 22 xr XRD9836 16-BIT PIXEL GAIN AFE REV. 1.0.0 Control / Polarity Register CNTRL / POL (01111) default D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 ADC POL LCLMP POL BSAMP POL VSAMP POL DLP DISABLE PWRDWN OEB RESET 0 0 0 0 0 0 0 0 The CNTRL / POL register is used to program various options including: input timing polarity control, dynamic low power disable, power down for the chip, output enable, and reset. Reset will reset ALL registers including reset. All the clock inputs (except the serial interface SCLK) can be programmed to be active high or active low. See the “Timing” section for more information. ADCpol, LCLMPpol, BSAMPpol, and VSAMPpol set the polarity of ADCLK, LCLMP, BSAMP, and VSAMP respectively. ADCpol - Sets the polarity of the ADCLK input. ADCpol = 0, ADCLK low during VSAMP. ADCpol = 0, ADCLK inverted so that it is high during VSAMP. LCLMPpol - Sets the polarity of the LCLMP input. LCLMPpol = 0, LCMLP is active high during clamping operation and odd pixel determined from falling edge. BSAMPpol - Sets the polarity of the BSAMP input. BSAMPpol = 0, BSAMP is active high. The CCD black level is sample by the falling edge. BSAMPpol = 1, BSAMP is active low. The CCD black level is sample by the rising edge. VSAMPpol - Sets the polarity of the VSAMP input. VSAMPpol = 0, VSAMP is active high. The CCD video level is sample by the falling edge. VSAMPpol = 1, VSAMP is active low. The CCD video level is sample by the rising edge. DLP DISABLE (ADC Dynamic Low Power Disable) PWRDWN - Puts the XRD9836 into power down state. PWRDWN = 0, normal operation. PWRDWN = 1, low power state. OEB - Enables the ADCDO bus. OEB = 0, data valid on ADCDO bus. OEB = 1, ADCDO bus high impedance. RESET - Will reset the XRD9836 to default (power up) conditions. RESET = 0, normal operation. RESET = 1, all internal registers set to default values and clears itself after ~ 10ns. 23 xr XRD9836 16-BIT PIXEL GAIN AFE REV. 1.0.0 Delay Registers D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 DelayA (10000) DelayA [7] DelayA [6] DelayA [5] DelayA [4] DelayA [3] DelayA [2] DelayA [1] DelayA [0] default 1 0 0 0 0 0 0 0 DelayB (10001) DelayB [7] DelayB [6] DelayB [5] DelayB [4] DelayB [3] DelayB [2] DelayB [1] DelayB [0] default 0 0 0 0 0 0 0 0 DelayC (10010) DelayC [7] DelayC [6] DelayC [5] DelayC [4] DelayC [3] DelayC [2] DelayC [1] DelayC [0] default 0 0 0 0 0 0 0 0 DelayD (10011) DelayD [7] DelayD [6] DelayD [5] DelayD [4] DelayD [3] DelayD [2] DelayD [1] DelayD [0] default 0 0 0 0 0 0 0 0 DelayA[7:4] - Controls the OGI_DLY. These bits are used to program the timing delay of the ADCLK used to sample the Offset-Gain-Inputs (OGI). Code 0000 is delay of 0ns, and code 1111 is 15ns. Default is 1000 = 7 ns. OGI_DLY should be larger than VSAMP_OGI_DLY. DelayA[3:0] - Controls the ADCO_DLY. These bits are used to program the timing delay of ADCO outputs in relation to ADCLK. Code 0000 is delay of 0ns, and code 1111 is 15ns. Default is 0000 = 0ns. This is used to adjust setup and hold times of the output, for the ASIC chip. DelayB[7:4] - Controls the BSAMP_LEADING_EDGE_DLY. These bits set the delay for the leading edge of the internal BSAMP pulse. Code 0000 is no delay. The delay increases by 0.5 ns per step to a total of 7.5 ns. Default is 0000 = 0ns. DelayB[3:0] - Controls the BSAMP_TRAILING_EDGE_DLY. These bits set the delay for the trailing edge of the internal BSAMP pulse. Code 0000 is no delay. The delay increases by 0.5 ns per step to a total of 7.5 ns. Default is 0000 = 0ns. DelayC[7:4] - Controls the VSAMP_LEADING_EDGE_DLY. These bits set the delay for the leading edge of the internal VSAMP pulse. Code 0000 is no delay. The delay increases by 0.5 ns per step to a total of 7.5 ns. Default is 0000 = 0ns. DelayC[3:0] - Controls the VSAMP_TRAILING_EDGE_DLY. These bits set the delay for the trailing edge of the internal VSAMP pulse. Code 0000 is no delay. The delay increases by 0.5 ns per step to a total of 7.5 ns. Default is 0000 = 0ns. DelayD[7:4] - Controls the VSAMP_OGI_DLY. These bits set the delay for the internal VSAMP that is used to transfer the OGI register data to the PGA & OFFSET control registers. DelayD[3:0] - Controls the ADC_DLY. These bits set the delay of the internal clock used for ADC operation. Code 0000 is no delay. The delay increases by 0.5 ns per step to a total of 7.5 ns. Default is 0000 = 0ns. 24 xr XRD9836 16-BIT PIXEL GAIN AFE REV. 1.0.0 Mode Register D9 D8 MODES of operation (10100) default D7 D6 D5 D4 D3 D2 D1 D0 NOFS2 TEST ENABLE GAIN SELECT CCD/CIS CHAN [1] CHAN [0] APOAM GOM 0 0 0 0 0 0 0 1 NOFS2 - No full scale divided by 2. Test Enable - Do not modify. Gain Select - Gain range is 1-10 for Gain Select = 0, and 2-20 for Gain Select = 1. CCD mode is selected if CCD/CIS is 0, CIS mode is selected if CCD/CIS is 1. Three channel is selected if CHAN[1] = 0 and CHAN[0] = 0. One channel red is selected if CHAN[1] = 0 and CHAN[0] = 1. One channel green is selected if CHAN[1] = 1 and CHAN[0] = 0. One channel blue is selected if CHAN[1] = 1 and CHAN[0] = 1. The Alternate Pixel Adjust Mode is selected by setting APOAM to 1. It is used only in Fixed Gain mode i.e. with GOM=0. The GOM (gain offset mode) bit is used to select either Fixed Gain Offset Mode (GOM=0) or Pixel by Pixel Gain Offset Mode (GOM=1). TEST D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 0 0 0 0 0 0 0 0 0 0 TEST (10101) default Test register used for factory test only. Do not modify 25 xr XRD9836 16-BIT PIXEL GAIN AFE REV. 1.0.0 TIMING DIAGRAMS tap tap X CCDIN X LCLMP tcp3 taclk3 taclk3 ADCLK tvfcr BSAMP tpwb tpwv tstl VSAMP tbvf tvbf tcr3 Clamp (Internal to XRD9836) FIGURE 17. 3-CHANNEL CDS MODE (ALL POLARITY BITS =0) tap tap CCDIN LCLMP tcp1 taclk1 taclk1 ADCLK tvfcr tpwb tbfcr BSAMP tstl VSAMP tcr1 tpwv tvbf tbvf Clamp (Internal to XRD9836) FIGURE 18. 1-CHANNEL CDS MODE (ALL POLARITY BITS=0) 26 xr XRD9836 16-BIT PIXEL GAIN AFE REV. 1.0.0 tap CIS tcp3 taclk3 tvfcr taclk3 ADCLK tstl VSAMP tcr3 tpwv FIGURE 19. 3-CHANNEL CIS MODE (ALL POLARITY BITS = 0, CCD/CIS BIT = 1) tap CIS tcp1 taclk1 taclk1 ADCCLK tvfcr tstl VSAMP tpwv tcr1 FIGURE 20. 1-CHANNEL CIS MODE (ALL POLARITY BITS = 0, CCD/CIS BIT = 1) 27 xr XRD9836 16-BIT PIXEL GAIN AFE REV. 1.0.0 Pixel (n) GAIN & OFFSET R R G G B B E E R R L L D D N N U U G G G a O a O a O i f i f i f n f n f n f OGI 10bit parallel IE Todih Tev Pixel (n-1) CCDOUT (Parallel RGB) Pixel (n) Pixel (n+1) Pixel (n+2) Pixel (n+3) Pixel (n+5) Pixel (n+4) BSAMP VSAMP CDS samples Red, Green, and Blue Tva Grn Pixel (n+1) Red Pixel (n+1) Blu Pixel (n) Grn Pixel (n) ADC Samples Red ADC Samples Green ADC Samples Blue Red Pixel (n) Blu Pixel (n-1) ADCLK R R G G B B D D D D D D H L H L H L tlat (9 ADCLK Latency) ADCDO 8-bit parallel Tadcdo FIGURE 21. 3-CHANNEL LATENCY FOR PARALLEL ADCDO (OUTPUT DATA BUS) & OGI (INPUT BUS) OGI 10bit parallel Gain (n) Offset (n) Gain (n+1) Offset (n+1) Gain (n+2) Offset (n+2) Gain (n+3) Offset (n+3) Gain (n+4) Offset (n+4) Gain (n+5) Offset (n+5) Gain (n+6) Offset (n+6) Gain (n+7) Offset (n+7) Gain (n+8) Offset (n+8) Gain (n+9) Offset (n+9) Gain (n+10) Offset (n+10) Gain (n+11) Offset (n+11) IE Togih Tev CCDOUT (Parallel RGB) Pixel (n-1) Pixel (n) Pixel (n+1) Pixel (n+2) Pixel (n+3) Pixel (n+4) Pixel (n+5) Pixel (n+6) Pixel (n+7) Pixel (n+8) Pixel (n+9) Pixel (n+10) BSAMP VSAMP Tva CDS samples input ADCLK tlat (9 ADCLK Latency) Pixel (n-1) ADCDO 8-bit parallel LSB's MSB's LSB's DH(n-1) DL(n-1) DH(n) DL(n) Tadcdo FIGURE 22. 1-CHANNEL LATENCY FOR PARALLEL ADCDO (OUTPUT DATA BUS) & OGI (INPUT BUS) 28 Pixel (n) MSB's xr XRD9836 16-BIT PIXEL GAIN AFE REV. 1.0.0 APPLICATION NOTES AND SCHEMATICS the XRD9836. All VDD’s should be supplied from a low noise, well filtered regulator which derives the power supply voltage from the CCD power supply. All of the AVDD pins are analog power supplies and should be decoupled locally to the nearest ground pin with at 0.1uF, high frequency capacitor. The DVDD and OVDD power pins should be locally decoupled to the nearest ground pin also. DVDD and OVDD should be connected to the same power supply network as the digital ASCI which receives data from the XRD9836. See Figure 23 for a typical CCD application hookup. The diagram shows an interface to a standard 3 channel output CCD. Both the ADC Output and OGI Control are parallel interfaces to the system ASIC controller. The timing inputs are provided by the system ASIC or timing generator (TG). The serial port control is typically sourced from a micro processor or the system ASIC. It is recommended that all AGND, DGND and OGND pins, be connected to the analog ground plane under 1uf 0.1uf 15V VDD3A VDD3D 1nf CCD A V D D RED+ 1nf A V D D A V D D D V D D O V D D It is recommended that each power pin be decoupled to ground with capacitors placed as close to power pin as possible. O V D D REDADCO7 ADCO6 ADCO5 ADCO4 ADCO3 ADCO2 ADCO1 ADCO0 1nf GRN+ 1nf GRN- 1nf ADC OUTPUT BUS BLU+ BLU- 1nf 9836 OGI9 OGI8 OGI7 OGI6 OGI5 OGI4 OGI3 OGI2 OGI1 OGI0 REXT 10K ASIC OGI CONTROL IE ADCCLKK TG (timing generator) VSAMP BSAMP CAPP CAPN A G N D D G N D O G N D O G N D CMREF 0.1uf 2.2uf 0.1uf A G N D 2.2uf A G N D 0.1uf SDIO 2.2uf LOAD SCLK ASIC 0.1uf 2.2uf LCLMP FIGURE 23. TYPICAL CCD APPLICATION DIAGRAM FOR THE XRD9836 The XRD9836 has an input range limitation of 1V maximum for a CCD input. If the maximum CCD output signal swing is greater than 1V, a resisitive divider network on the inputs can be used to reduce the CCD output to meet the 1V input max requirement of the XRD9836 inputs. See Figure 24 for a typical implementation of a resistor divider. Each input channel will require a matching divider network. 15V Vin R1 C1 1nf XRD9836 RED+ R2 Vsig CCD C2 1nf RED - Vin = Vsig (R1/(R1+R2)) FIGURE 24. INPUT RESISTIVE DIVIDER NETWORK 29 xr XRD9836 16-BIT PIXEL GAIN AFE REV. 1.0.0 Supply Current vs. Temperature 115 VDD = 3.3V Fs = 30MHz 3-Channel Mode Idd(mA) 105 95 85 75 -5 5 15 25 35 45 55 65 75 Temperature(C) FIGURE 25. XRD9836 TYPICAL IDD VS TEMPERTURE 9836 System DNL 2 1.5 Dnl (lsb) 1 0.5 0 -0.5 -1 -1.5 0 8192 16384 24576 32768 40960 Code FIGURE 26. TYPICAL XRD9836 DNL FOR RED CHANNEL IN 3-CH MODE 30 49152 57344 65536 xr XRD9836 16-BIT PIXEL GAIN AFE REV. 1.0.0 PACKAGE DRAWING: 31 xr XRD9836 1.0.0 16BIT PIXEL GAIN AFE 8/15/03 NOTICE EXAR Corporation reserves the right to make changes to the products contained in this publication in order to improve design, performance or reliability. EXAR Corporation assumes no responsibility for the use of any circuits described herein, conveys no license under any patent or other right, and makes no representation that the circuits are free of patent infringement. Charts and schedules contained here in are only for illustration purposes and may vary depending upon a user’s specific application. While the information in this publication has been carefully checked; no responsibility, however, is assumed for inaccuracies. EXAR Corporation does not recommend the use of any of its products in life support applications where the failure or malfunction of the product can reasonably be expected to cause failure of the life support system or to significantly affect its safety or effectiveness. Products are not authorized for use in such applications unless EXAR Corporation receives, in writing, assurances to its satisfaction that: (a) the risk of injury or damage has been minimized; (b) the user assumes all such risks; (c) potential liability of EXAR Corporation is adequately protected under the circumstances. Copyright 2003 EXAR Corporation Datasheet June 2003. Reproduction, in part or whole, without the prior written consent of EXAR Corporation is prohibited. 32