XRP6670EHTR-F

XRP6670 3A 300kHz-2.5MHz Synchronous Step Down Regulator November 2019 Rev. 1.0.2 GENERAL DESCRIPTION APPLICATIONS • Industrial & Medical Equipment The XRP6670 is a synchronous current mode PWM step-down (buck) regulator capable of delivering up to 3 Amps. A 2.6V to 5.5V input voltage range allows for single supply operation from industry standard 3.3V and 5V power rails. • Audio-Video Equipment • Networking & Telecom Equipment • Portable/Battery Operated Equipment Based on a current mode PWM control scheme, the XRP6670 operating frequency is programmable between 300kHz and 2.5MHz via an external resistor. This flexibility allows the XRP6670 to optimize component selection and reduce component count and solution footprint. It provides a low output voltage ripple, excellent line and load regulation and has a 100% duty cycle LDO mode. Output voltage is adjustable to as low as 0.8V with a better than 2% accuracy while a low quiescent current supports the most stringent battery operating conditions. FEATURES • Guaranteed 3A Output Current − Input Voltage: 2.6V to 5.5V • Prog. PWM Current Mode Control − Programmable 300kHz to 2.5MHz − 100% Duty Cycle LDO Mode Operation − Achieves 95% Efficiency • Adjustable Output Voltage Range − 0.8V to 5V with ±2% Accuracy • Enable and Power Good Functions Built-in over-temperature, overcurrent, short circuit and under-voltage lock-out protections insure safe operations under abnormal operating conditions. • 460µA Quiescent Current • Over-temperature, Over-current, Short-circuit and UVLO Protections The XRP6670 is offered in a RoHS compliant, “green”/halogen free 3mmx3mm 10-pin DFN package. • RoHS Compliant “Green”/Halogen Free 3mm x 3mm 10-Pin DFN Package TYPICAL APPLICATION DIAGRAM Fig. 1: XRP6670 Application Diagram 1/13 Rev. 1.0.2 XRP6670 3A 300kHz-2.5MHz Synchronous Step Down Regulator ABSOLUTE MAXIMUM RATINGS OPERATING RATINGS These are stress ratings only and functional operation of the device at these ratings or any other above those indicated in the operation sections of the specifications below is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability. Input Voltage Range VIN ............................... 2.6V to 5.5V Maximum Output Current (Min.) ................................. 3A Junction Temperature Range ................. -40°C to +125°C Thermal Resistance ...................................................... DFN10 θJA ....................................................110°C/W DFN10 θJC ....................................................... 3°C/W VDD, PVDD, FB, COMP, SHDN/RT ................... -0.3V to 6.0V SW ................................................... -0.3V to VDD+0.3V Junction Temperature Range............................... +150°C Storage Temperature .............................. -65°C to 150°C Power Dissipation ................................ Internally Limited Lead Temperature (Soldering, 10 sec) ................... 260°C ESD Rating (HBM - Human Body Model) .................... 2kV ESD Rating (MM - Machine Model) ...........................200V Note 1: TJ is a function of the ambient temperature TA and power dissipation PD: (TJ = TA + (PD * θJA)) ELECTRICAL SPECIFICATIONS Specifications are for an Operating Junction Temperature of TA = TJ = 25°C only; limits applying over the full Operating Junction Temperature range are denoted by a “•”. Minimum and Maximum limits are guaranteed through test, design, or statistical correlation. Typical values represent the most likely parametric norm at TJ = 25°C, and are provided for reference purposes only. Unless otherwise indicated, VDD = VPVDD = 3.3V, TA= TJ = 25°C. Parameter Min. Typ. Max. 460 Supply Current 1 Shutdown Supply Current Units µA VFB=0.75V, No switching µA SHDN/RT=VDD=VPVDD=5.5V Under Voltage Lockout (UVLO) Threshold 2.2 V Under Voltage Lockout (UVLO) Hysteresis 300 mV Feedback Voltage VFB 0.800 0.816 V FB Pin Bias Current 0.1 0.4 µA Current Sense Transresistance 0.2 1 µA 0.784 Switching Leakage Current 800 V/V Error Amplifier Transconductance 800 µA/V Switching Frequency Range Maximum Duty Cycle 0.760 0.800 0.3 0.8 1 0.840 V 2.5 MHz 1.2 120 150 ns Programmed via ROSC VFB=0.75V A VFB=0.75V Switching FET On Resistance 0.11 0.16 Ω ISW=500mA Synchronous FET On Resistance 0.11 0.17 Ω ISW=500mA VDD-0.7 VDD-0.4 V +15 % 120 Ω Switch Current Limit 3.2 Shutdown Threshold PGOOD Voltage Range 4.2 SHDN/RT=VDD=5.5V ROSC=330kΩ % 100 Minimum On-Time VDD rising Ω Error Amplifier Voltage Gain RT Pin Voltage Conditions -15 PGOOD Pull Down Resistance Output Current A 3 VDD= 2.6V to 5.5V, VOUT= 2.5V Output Voltage Line Regulation 0.4 %/V Output Voltage Load Regulation ±0.2 % IOUT= 10mA to 3A Soft Start Time 1.5 ms IOUT= 10mA Thermal Shutdown Temperature 160 °C 20 °C Thermal Shutdown Hysteresis 2/13 VDD= 2.7V to 5.5V, IOUT= 100mA Rev. 1.0.2 XRP6670 3A 300kHz-2.5MHz Synchronous Step Down Regulator BLOCK DIAGRAM Fig. 2: XRP6670 Block Diagram PIN ASSIGNMENT Fig. 3: XRP6670 Pin Assignment 3/13 Rev. 1.0.2 XRP6670 3A 300kHz-2.5MHz Synchronous Step Down Regulator PIN DESCRIPTION Name Pin Number Description SHDN/RT 1 Shutdown and Oscillator resistor input. Connect a resistor to GND from this pin to set the switching frequency. Forcing this pin to VDD shuts down the device. GND 2 Signal ground. All small-signal ground, such as the compensation components and exposed pad should be connected to this, which in turn connects to PGND at one point. SW 3, 4 PGND 5 Power Ground Signal. Connect this signal as close as possible to the input and output capacitors CIN and COUT. PVDD 6 Power Input Supply Pin. Decouple this pin to PGND (pin 5) with a capacitor. VDD 7 Signal Input Supply Pin. Decouple this pin to GND (pin 2) with a capacitor. Typically, VDD and PVDD are connected together. PGOOD 8 Power Good Flag. This is an open drain output and is pulled to ground if the output voltage is out of regulation. FB 9 Feedback pin. An external resistor divider connected to FB programs the output voltage. COMP 10 Exp. Pad Exp. Pad Power switch output pin. This pin is connected to the inductor. Compensation pin. This is the output of transconductance error amplifier and the input to the current comparator. It is used to compensate the control loop. Connect an RC network form this pin to GND. Connect to GND signal (pin 2). ORDERING INFORMATION(1) Part Number XRP6670EHTR-F XRP6670EVB Junction Temperature Range -40°C ≤ TJ ≤ +125°C Package Packing Method Tape & Reel DFN10 XRP6670 Evaluation Board Lead Free(2) Yes Notes: 1. Refer to www.maxlinear.com/XRP6670 for most up-to-date Ordering Information. 2. Visit www.maxlinear.com for additional information on Environmental Rating. 4/13 Rev. 1.0.2 XRP6670 3A 300kHz-2.5MHz Synchronous Step Down Regulator TYPICAL PERFORMANCE CHARACTERISTICS All data taken at VIN = VDD = VPVDD = 3.3V, TJ = TA = 25°C, unless otherwise specified - Schematic and BOM from Application Information section of this datasheet. Fig. 4: Supply Current Versus Input Voltage Fig. 5: Supply Current versus Ambient Temperature Fig. 6: Efficiency versus Output Current Fig. 7: PMOS RDSON Resistance versus Ambient Temperature Fig. 8: NMOS RDSON Resistance versus Ambient Temperature Fig. 9: Frequency versus Ambient Temperature 5/13 Rev. 1.0.2 XRP6670 3A 300kHz-2.5MHz Synchronous Step Down Regulator Fig. 10: VFB versus Ambient Temperature Fig. 11: Current Limit versus Ambient Temperature VOUT AC 200mV/div IOUT 1AV/div Time 20µs/div Fig. 13: Load Transient Response VIN=5V, VOUT=2.5V, IOUT=0A to 3A Fig. 12: Start-up from VIN VIN=3.3V, VOUT=2.5V, IOUT=3A Fig. 15: Short Circuit Recovery VIN=3.3V, VOUT=2.5V Fig. 14: Short Circuit Protection VIN=3.3V, VOUT=2.5V 6/13 Rev. 1.0.2 XRP6670 3A 300kHz-2.5MHz Synchronous Step Down Regulator THEORY OF OPERATION POWER GOOD FLAG This open drain output (PGOOD) can be used to monitor whether the output voltage is within regulation (±15%). PGOOD is pulled to ground when VOUT is not in regulation. PGOOD should be tied to VDD with a 100k resistor. FUNCTIONAL DESCRIPTION The XRP6670 is a synchronous, current-mode, step-down regulator. It regulates input voltages from 2.6V to 5.5V and supplies up to 3A of output current IOUT. The XRP6670 uses current-mode control to regulate the output voltage VOUT. The VOUT is measured at FB through a resistive voltage divider and input to a transconductance error amplifier. The highside switch current is compared to the output of the error amplifier to control the output voltage. The regulator utilizes internal Pchannel and N-channel MOSFETs to step-down the input voltage. Because the high-side FET is P-channel a bootstrapping capacitor is not necessary and the regulator can operate at 100% duty cycle. The XRP6670 has several powerful protection features including OCP, OTP, UVLO and output short-circuit. PROGRAMMABLE FREQUENCY The switching frequency is programmable within a range of 300kHz to 2.5MHz via a resistor placed between SHDN/RT and GND pins. An equation for calculating a resistor value for a target frequency is given the Application Information section. 100% DUTY CYCLE AND LDO OPERATION The XRP6670 switching FET is a P-channel device and therefore can operate at 100% duty cycle. In battery operated applications where VIN will droop, XRP6670 can seamlessly transition from PWM to LDO mode. SHORT-CIRCUIT AND OVER-CURRENT PROTECTION OCP OVER-TEMPERATURE PROTECTION OTP If the junction temperature exceeds 160°C the OTP circuit is triggered, turning off the internal control circuit and FETs. When junction temperature drops below 140°C the XRP6670 will restart. The XRP6670 protects itself and downstream circuits against accidental increase in current or short-circuit. If peak current through the switching FET increases above 4.2A (nominal) the regulator enters an idle state where the internal FETs are turned off and softstart is pulled low. After a period of 2000xT the regulator will attempt a softstart. If the high current persists the protection cycle will repeat. Although thermal shutdown is built-in in the XRP6670 to protect the device from thermal damage, the total power dissipation that the XRP6670 can sustain is based on the package thermal capability. Equation 1 shown on page two, can be used to calculate junction temperature and ensure operation within the recommended maximum temperature of 125°C. SOFT-START XRP6670 has an integrated soft-start which is preset at 1.5ms (nominal). This feature limits the inrush current during startup and allows the output voltage to smoothly rise to its programmed value. APPLICATION INFORMATION PROGRAMMING THE OUTPUT VOLTAGE Where: Use an external resistor divider to set the output voltage based on the following equation: 𝑅𝑅2 = 𝑅𝑅1 𝑉𝑉𝑂𝑂𝑂𝑂𝑂𝑂 − 1� � 0.800𝑉𝑉 R1 is the resistor between VOUT and FB (nominally set at 100kΩ) 7/13 Rev. 1.0.2 XRP6670 3A 300kHz-2.5MHz Synchronous Step Down Regulator R2 is the resistor between FB and GND DUTY-CYCLE LIMITATION 0.800V is the nominal feedback voltage XRP6670 has a “Minimum On-Time” specification of 150ns which imposes a restriction on minimum duty-cycle (see table 2) A resistor selection guide for common values of VOUT is shown in table 1. VOUT R1(kΩ) R2(kΩ) 1.1V 1.2V 1.5V 1.8V 2.5V 2.8V 3.3V 100 100 105 120 100 75 75 267 200 120 95.3 47 30 24 F (MHz) TTYP(ns) TMIN(ns) Duty-cycleMIN 1.0 2.0 1000 500 800 400 0.19 0.38 Table 2: Minimum duty-cycle arising from “Minimum On-Time) For example if frequency is set at 2MHz then typical switching period is 500ns. Allowing a ±20% uncertainty, minimum period is 400ns and corresponding minimum duty-cycle is 0.38. Recall that for a buck regulator dutycycle=VOUT/VIN. Therefore when operating at 2MHz with VIN of 5V, a VOUT≤1.9V is not possible (5V x 0.38 = 1.9V). Table 1: Resistor Selection PROGRAMMING THE FREQUENCY Use resistor ROSC between SHDN/RT and GND pins to program the switching frequency. A graph of nominal frequency versus ROSC is shown in figure 16. OUTPUT INDUCTOR Select the output inductor for inductance L, DC current rating IDC and saturation current rating ISAT. IDC should be larger than regulator output current. ISAT, as a rule of thumb, should be 50% higher than the regulator output current. Since the regulator is rated at 3A then IDC≥3A and ISAT≥4.5A. Please note that “Peak Switch Current” is rated at 3.2A minimum. Therefore applications that require an output current of 3A should limit the peak-to-peak inductor current ripple to ΔIL≤0.4A. In the following we will use the common practice of ΔIL≤1A. Therefore worstcase maximum output current will be limited to IOUT=3.2A-0.5A=2.7A. Fig. 16: Frequency versus ROSC Calculate the inductance from: The following equation closely fits the empirical data and can be used to select ROSC for a given frequency. 𝑹𝑹𝑶𝑶𝑶𝑶𝑶𝑶 Where: 𝐿𝐿 = (𝑉𝑉𝐼𝐼𝐼𝐼 − 𝑉𝑉𝑂𝑂𝑂𝑂𝑂𝑂 ) � 𝑉𝑉𝑂𝑂𝑂𝑂𝑂𝑂 � 𝛥𝛥𝐼𝐼𝐿𝐿 × 𝑓𝑓𝑠𝑠 × 𝑉𝑉𝐼𝐼𝐼𝐼 ΔIL is peak-to-peak inductor current ripple nominally set to ≤30% of IOUT 𝟗𝟗. 𝟐𝟐𝟐𝟐 × 𝟏𝟏𝟏𝟏𝟏𝟏𝟏𝟏 = 𝒇𝒇𝟏𝟏.𝟎𝟎𝟎𝟎𝟎𝟎 fS is nominal switching frequency As an example, inductor values corresponding to 5VIN/1MHz and 3.3VIN/1MHz are shown in tables 3 and 4 for several common output 8/13 Rev. 1.0.2 XRP6670 3A 300kHz-2.5MHz Synchronous Step Down Regulator ILow is the value of load-step after unloading. This is nominally set equal to 50% of regulator current rating (1.5A). voltages. Note that example inductors shown in tables 3 and 4 are Wurth shielded inductors. VOUT(V) ΔIL(p-p)(A) 3.3 2.8 2.5 1.8 1.5 1.2 1.1 0.76 0.81 0.84 0.76 0.70 0.62 0.57 L(µH) Inductor Example 1.5 1.5 1.5 1.5 1.5 1.5 1.5 74437346015 74437346015 74437346015 74437346015 74437346015 74437346015 74437346015 Vtransient is the maximum permissible voltage transient corresponding to the load step mentioned above. Vtransient is typically specified from 3% to 5% of VOUT. ESR of the capacitor has to be selected such that the output voltage ripple requirement ΔVOUT, nominally 1% of VOUT, is met. Voltage ripple ΔVOUT is mainly composed of two components: the resistive ripple due to ESR and capacitive ripple due to COUT charge transfer. For applications requiring low voltage ripple, ceramic capacitors are recommended because of their low ESR which is typically in the range of 5mΩ. Therefore ΔVOUT is mainly capacitive. For ceramic capacitors calculate the ΔVOUT from: Table 3: Suggested Inductor Values for f=1MHz, VIN=5V and IOUT=2.7A VOUT(V) ΔIL(p-p)(A) 2.5 1.8 1.5 1.2 1.1 0.41 0.54 0.54 0.51 0.49 L(µH) Inductor Example 1.5 1.5 1.5 1.5 1.5 74437346015 74437346015 74437346015 74437346015 74437346015 Where: Table 4: Suggested Inductor Values for f=1MHz, VIN=3.3V and IOUT=2.7A 𝛥𝛥𝑉𝑉𝑂𝑂𝑂𝑂𝑇𝑇 = 𝛥𝛥𝐼𝐼𝐿𝐿 8 × 𝐶𝐶𝑂𝑂𝑂𝑂𝑂𝑂 × 𝑓𝑓𝑠𝑠 ΔIL is from table 2 or 3 OUTPUT CAPACITOR COUT COUT is the value calculated above Select the output capacitor for voltage rating, capacitance COUT and Equivalent Series Resistance ESR. The voltage rating, as a rule of thumb, should be at least twice the output voltage. When calculating the required capacitance, usually the overriding requirement is current load-step transient. If the unloading transient (i.e., when load transitions from a high to a low current) is met, then usually the loading transient (when load transitions from a low to a high current) is met as well. Therefore calculate the COUT based on the unloading transient requirement from: fs is nominal switching frequency 𝐶𝐶𝑂𝑂𝑂𝑂𝑂𝑂 = 𝐿𝐿 × � Where: 2 𝐼𝐼𝐻𝐻𝐻𝐻𝐻𝐻ℎ − 𝐼𝐼𝐿𝐿𝐿𝐿𝐿𝐿 2 (𝑉𝑉𝑂𝑂𝑂𝑂𝑂𝑂 + 𝑉𝑉𝑡𝑡𝑡𝑡𝑡𝑡𝑡𝑡𝑡𝑡𝑡𝑡𝑡𝑡𝑡𝑡𝑡𝑡 )2 − 𝑉𝑉𝑂𝑂𝑂𝑂𝑂𝑂 2 If tantalum or electrolytic capacitors are used then ΔVOUT is essentially a function of ESR: 𝛥𝛥𝑉𝑉𝑂𝑂𝑂𝑂𝑂𝑂 = 𝛥𝛥𝐼𝐼𝐿𝐿 × 𝐸𝐸𝐸𝐸𝐸𝐸 INPUT CAPACITOR CIN Select the input capacitor for voltage rating, RMS current rating and capacitance. The voltage rating should be at least 50% higher than the regulator’s maximum input voltage. Calculate the capacitor’s current rating from: Where: � 𝐼𝐼𝐶𝐶𝐼𝐼𝐼𝐼,𝑅𝑅𝑅𝑅𝑅𝑅 = 𝐼𝐼𝑂𝑂𝑂𝑂𝑂𝑂 × �𝐷𝐷 × (1 − 𝐷𝐷) IOUT is regulator’s maximum current (3A) D is duty cycle (D=VOUT/VIN) L is the inductance calculated in the preceding step Calculate the CIN capacitance from: IHigh is the value of load-step prior to unloading. This is nominally set equal to regulator current rating (3A). 9/13 𝐶𝐶𝐼𝐼𝐼𝐼 = 𝐼𝐼𝑂𝑂𝑂𝑂𝑂𝑂 × 𝑉𝑉𝑂𝑂𝑂𝑂𝑂𝑂 × (𝑉𝑉𝐼𝐼𝐼𝐼 − 𝑉𝑉𝑂𝑂𝑂𝑂𝑂𝑂 ) 𝑓𝑓𝑠𝑠 × 𝑉𝑉𝐼𝐼𝐼𝐼 2 × 𝛥𝛥𝑉𝑉𝐼𝐼𝐼𝐼 Rev. 1.0.2 XRP6670 3A 300kHz-2.5MHz Synchronous Step Down Regulator Where: The uncompensated regulator has a constant gain up to its pole frequency, beyond which the gain decreases at -20dB/decade. The zero arising from the output capacitor’s ESR is inconsequential if ceramic COUT is used. This simplifies the compensation. The RC and CC, which are placed between the output of XRP6670’s Error Amplifier and ground, constitute a zero. The frequency of this compensating zero is given by: ΔVIN is the permissible input voltage ripple, nominally set at 1% of VIN LOOP COMPENSATION XRP6670 utilizes current-mode control. This allows using a minimum of external components to compensate the regulator. In general only two components are needed: RC and CC. Proper compensation of the regulator (determining RC and CC) results in optimum transient response. In terms of power supply control theory, the goals of compensation are to choose RC and CC such that the regulator loop gain has a crossover frequency fc equal to 10% of switching frequency. The corresponding phase-margin should be between 45 degrees and 65 degrees. An important characteristic of current-mode buck regulator is its dominant pole. The frequency of the dominant pole is given by: 𝑓𝑓𝑝𝑝 = 𝑓𝑓𝑧𝑧 = 1 2𝜋𝜋 × 𝑅𝑅𝑅𝑅 × 𝐶𝐶𝐶𝐶 For the typical application circuit shown in this datasheet, RC=10kΩ and CC=1nF provide a satisfactory compensation. Please use EXAR application note for compensating other application circuits. 1 2𝜋𝜋 × 𝐶𝐶𝑂𝑂𝑂𝑂𝑂𝑂 × 𝑅𝑅𝑙𝑙𝑙𝑙𝑙𝑙𝑙𝑙 where Rload is the output load resistance. 10/13 Rev. 1.0.2 XRP6670 3A 300kHz-2.5MHz Synchronous Step Down Regulator TYPICAL APPLICATIONS 5V TO 3.3V CONVERSION – 1MHZ Fig. 17: 3.5V-5.5V to 3.3V Conversion 1MHz Switching Operations 5V TO 3.3V CONVERSION – 2.5MHZ Fig. 18: 4V-5.5V to 3.3V Conversion 2.5MHz Switching Operations 11/13 Rev. 1.0.2 XRP6670 3A 300kHz-2.5MHz Synchronous Step Down Regulator PACKAGE SPECIFICATION 3MM X 3MM DFN-10 12/13 Rev. 1.0.2 XRP6670 3A 300kHz-2.5MHz Synchronous Step Down Regulator REVISION HISTORY Revision Date Description 1.0.0 03/19/2013 Initial release of datasheet 1.0.1 06/20/2013 Corrected CC=1nF on page 10 1.0.2 11/01/2019 Updated to MaxLinear logo. Updated Ordering Information. CORPORATE HEADQUARTERS: 5966 La Place Court Suite 100 Carlsbad, CA 92008 Tel.: +1 (760) 692-0711 Fax: +1 (760) 444-8598 www.maxlinear.com The content of this document is furnished for informational use only, is subject to change without notice, and should not be construed as a commitment by Maxlinear, Inc. Maxlinear, Inc. Assumes no responsibility or liability for any errors or inaccuracies that may appear in the informational content contained in this guide. Complying with all applicable copyright laws is the responsibility of the user. Without limiting the rights under copyright, no part of this document may be reproduced into, stored in, or introduced into a retrieval system, or transmitted in any form or by any means (electronic, mechanical, photocopying, recording, or otherwise), or for any purpose, without the express written permission of Maxlinear, Inc. Maxlinear, Inc. Does not recommend the use of any of its products in life support applications where the failure or malfunction of the product can reasonably be expected to cause failure of the life support system or to significantly affect its safety or effectiveness. Products are not authorized for use in such applications unless Maxlinear, Inc. Receives, in writing, assurances to its satisfaction that: (a) the risk of injury or damage has been minimized; (b) the user assumes all such risks; (c) potential liability of Maxlinear, Inc. Is adequately protected under the circumstances. Maxlinear, Inc. May have patents, patent applications, trademarks, copyrights, or other intellectual property rights covering subject matter in this document. Except as expressly provided in any written license agreement from Maxlinear, Inc., the furnishing of this document does not give you any license to these patents, trademarks, copyrights, or other intellectual property. Maxlinear, the Maxlinear logo, and any Maxlinear trademarks, MxL, Full-Spectrum Capture, FSC, G.now, AirPHY and the Maxlinear logo are all on the products sold, are all trademarks of Maxlinear, Inc. or one of Maxlinear’s subsidiaries in the U.S.A. and other countries. All rights reserved. Other company trademarks and product names appearing herein are the property of their respective owners. © 2013 - 2019 Maxlinear, Inc. All rights reserved. 13/13 Rev. 1.0.2