RFMA0912-0.5W-Q7
UPDATED: 04/22/2008
9.5 – 11.7 GHz High Gain Surface-Mounted PA
FEATURES
• • • • • • • 9.5 – 11.7GHz Operating Frequency Range 27.0dBm Output Power @1dB Compression 30.0dB Typical Power Gain @1dB Compression -41dBc OIMD3 @Pout 16dBm/tone 7X7mm QFN Package Point-to-point and point-to-multipoint radio Military Radar Systems PARAMETER/TEST CONDITIONS Operating Frequency Range Output Power @1dB Gain Compression Gain @1dB Gain Compression Output 3 Order Intermodulation Distortion @∆f=10MHz, Pout = 16dBm/tone Input Return Loss Output Return Loss Drain Current1 Drain Current1 Drain Voltage Gate Voltage Thermal Resistance2 Operating Base Plate Temperature -30 -2.5 13 +80
rd
APPLICATIONS ELECTRICAL CHARACTERISTICS (TB=25 °C)
SYMBOL F P1dB G1dB OIMD3 Input RL Output RL ID1 ID2 VD1, VD2 VG1, VG2 Rth Tb MIN 9.5 26.0 27.0 27.0 30.0 -41 -10 -6 190 400 7 220 460 8 -0.25
o
TYP
MAX 11.7
UNITS GHz dBm dB
-38 -8
dBc dB dB mA mA V V C/W
o
C
1. Recommended to bias each amplifier stage separately using a gate voltage range, starting from -2.5 to -0.3V to achieve typical current levels. 2. Rth is mounting dependent. Measured result when used with Excelics recommended evaluation board. 3,4
MAXIMUM RATINGS AT 25°C
SYMBOL VD1, VD2 VG1, VG2 ID1, ID2 PIN TCH TSTG PT Drain to Source Voltage Gate to Source Voltage Drain Current Input Power Channel Temperature Storage Temperature Total Power Dissipation
CHARACTERISTIC
ABSOLUTE 12V -5V Idss 20dBm 175°C -65/175°C 8.8W
CONTINOUS 8V -2.5 V 220, 460mA @ 3dB compression 150°C -65/150°C 7.4W
3. Operation beyond absolute or continuous ratings may result in permanent damage or reduction of MTTF respectively. 4. Bias conditions must also satisfy the following equation VDS*IDS < (TCH –TB)/RTH; where TB = Temperature of Base Plate Specifications are subject to change without notice. Excelics Semiconductor, Inc. 310 De Guigne Drive, Sunnyvale, CA 94085 Phone: 408-737-1711 Fax: 408-737-1868 Web: www.excelics.com
page 1 of 3 Revised May 2008
RFMA0912-0.5W-Q7
UPDATED: 04/22/2008
9.5 – 11.7 GHz High Gain Surface-Mounted PA
Package Dimension and Pin Assignment
0.276±0.002
0.276±0.002
22
28
EXCELICS RFMA0912 -0.5W-Q7
0 REF 0.049 MAX 0.008 0 REF 0 REF
0.240
21
1
0.038 0.036 0.013 0 REF
15 14 8
7
0.012±0.002
0.032±0.002
* All measurements in inches
Additional Notes: 1) Ground Plane must be soldered to PCB RF ground 2) All dimensions are in inches 3) Refer to Excelics application notes on QFNs for further guidelines 4) Pin Assignment:
Top View
Vd1 Vd2
Bottom View
Vd2
22
Vd1
28
RFin
EXCELICS RFMA0912 -0.5W-Q7
Vg1 Vg2
21
1
RFout
RFout
RFin
15 14 8
7
Vg2
Vg1
Pin 1, 2, 3, 5, 6, 7, 8, 10, 11, 12, 14 4 9 13 15, 16, 17, 19, 20, 21, 22, 24, 25, 26, 28 18 23 27
Assignment NC RFin Vg1 Vg2 NC RFout Vd2 Vd1
page 2 of 3 Revised May 2008
Specifications are subject to change without notice. Excelics Semiconductor, Inc. 310 De Guigne Drive, Sunnyvale, CA 94085 Phone: 408-737-1711 Fax: 408-737-1868 Web: www.excelics.com
RFMA0912-0.5W-Q7
UPDATED: 04/22/2008
9.5 – 11.7 GHz High Gain Surface-Mounted PA
Recommended Circuit Schematic:
Vd1
22uF 0.1uF NC
Vd2
Vd1
NC NC NC
Vd2
0.1uF NC
22uF
NC NC NC
RFin
NC NC NC
EXCELICS RFMA0912 -0.5W-Q7
NC
NC NC NC
RFout
NC NC NC
Vg1
NC
NC
NC
Vg2
NC
Vg1
22uF 0.1uF 0.1uF 22uF
Vg2
Notes: 1) External bypass capacitors should be placed as close to the package as possible. 2) Dual biasing sequence required: a. Turn-on Sequence: Apply Vg1 = -2.5V, Vg2 = -2.5V, followed by Vd1 = Vd2 = 7V, lastly increase Vg1 & Vg2 in sequence until required Id1 and Id2 is obtained. b. Turn-off Sequence: Turn off Vd1 & Vd2, followed by Vg1 & Vg2 3) Demonstration board available upon request.
Specifications are subject to change without notice. Excelics Semiconductor, Inc. 310 De Guigne Drive, Sunnyvale, CA 94085 Phone: 408-737-1711 Fax: 408-737-1868 Web: www.excelics.com
page 3 of 3 Revised May 2008
很抱歉,暂时无法提供与“RFMA0912-0.5W-Q7”相匹配的价格&库存,您可以联系我们找货
免费人工找货