RT30

User's Guide Wireless AC Circuit Identifier Models RT30 and RT32 Introduction Congratulations on your purchase of Extech’s Model RT30 (914Mhz) or RT32 (869MHz) Wireless AC Circuit Identifier. The detector can identify live circuits and detect changes in light level with the wireless receiver. With careful use, this detector will provide years of reliable service. Meter Description TRANSMITTER DESCRIPTION 1 9 4 5 6 7 8 2 3 12 1. 2. 3. 4. 5. 6. 7. 8. 9. Wire clamp slot Wire Clamp release latch Light sensor Voltage/Light detect LED Battery compartment Power LED Light setpoint button Power/Mode select switch External Probe Connector RECEIVER DESCRIPTION 1. 2. 3. 4. 5. 6. 7. Detect LED (Amber) Communication LED (Yellow) Power/Mode Power LED (Green) Battery compartment Pocket clip Audio Buzzer 2 5 RT30 V2.0 11/08 7 6 3 4 Operation Detecting Live Circuits (VOLTAGE method) The RT30 can be directly clamped on installed building wiring and will detect the voltage applied to the wiring. 1. 2. 3. Slide the transmitter power switch to the VOLTAGE position. The POWER LED will switch on. Slide the Receiver power switch to the ON position. The POWER LED and the SIGNAL OK LED will switch ON. Place the RomexTM/nm cable (AC wire) directly into the wire clamp slot or, alternatively, connect the external voltage detector probe into the external probe socket and then clamp the probe to any cable, extension cord or appliance cord. If the cable is “live” (voltage present), the VOLTAGE/LIGHT amber LED on the transmitter will switch on and the DETECT LED on the receiver will switch on. If desired, switch the receiver power switch to the audio OFF position disable the audible tone. 6. to 4. 5. When the voltage is removed (by opening the splice or the circuit breaker, for example), the Detect LEDs will switch OFF and the detect beeper will switch OFF. Note: Use of the External Probe overrides the setting of the Power/Mode Switch. The Lighting method cannot be used while the External Probe is attached. 3 RT30 V2.0 11/08 Detecting Live Circuits (LIGHTING method) In situations where access to circuit wiring is limited, the RT30 can also detect room lighting changes (ON to OFF). 1. 2. 3. 4. Slide the transmitter power switch to the LIGHT position. The POWER LED will switch on. Slide the Receiver power switch to the ON position. The POWER LED will switch on. Cover the Light Sensor on the transmitter and press the Light Setpoint button. Expose the Light Sensor to the light source. The VOLTAGE/LIGHT LED on the transmitter and the DETECT LED on the receiver will switch on When the lights are turned off the VOLTAGE/LIGHT LED on the transmitter and the DETECT LED on the receiver will switch off, indicating the light has been switched off and power has been removed. 5. Note: Before use, always test the light on/off operation for proper sensitivity and detection. Support line (781) 890-7440 Technical Support: Extension 200; E-mail: support@extech.com Repair & Returns: Extension 210; E-mail: repair@extech.com Product specifications subject to change without notice For the latest version of this User Guide, Software updates, and other up-to-the-minute product information, visit our website: www.extech.com Extech Instruments Corporation, 285 Bear Hill Road, Waltham, MA 02451 4 RT30 V2.0 11/08 Specifications Transmitter Unit Indicators Transmission Frequency Transmission Distance Transmission Power Alarm Status Power Supply Battery Life Operating Temperature Storage Temperature Operating Humidity Storage Humidity Dimensions Weight LED RT30 (914MHz) RT32 (869MHz) Receiver Unit Audio Beeper, LED n/a Approx. 328’ (100m) in an unobstructed field +10dBm Visual Two (2) ‘AAA’ batteries n/a Visual and audible Two (2) ‘AAA’ batteries 80 hours (approximately) 14 to 122°F (-10 to 50°C) -14 to 140°F (-30 to 60°C) 90% RH from 32-86°F (-10 to 30°C) 75% RH from 86-104°F (30 to 40°C) 45% RH from 104-122°F (40 to 50°C) 90% RH max. 4.0x2.4x1.5” (101x61x38mm) 4.5x1.17x 1.02” (114x30x26mm) 8.0 oz.(0.23 kg) – three (3) piece total 5 RT30 V2.0 11/08 Maintenance Battery Replacement When the Power LED begins to dim, or the transmitter and receiver stop communicating, the batteries may need to be replaced. Each unit uses two (2) ‘AAA’ batteries (MN2400 or equivalent). The battery doors can be removed using a Philips screwdriver to loosen the attaching screw. Calibration and Repair Services Extech offers repair and calibration services for the products we sell. Extech also provides NIST certification for most products. Call the Customer Care Department for information on calibration services available for this product. Extech recommends that annual calibrations be performed to verify meter performance and accuracy. FCC Part 15 (RT30) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 6 RT30 V2.0 11/08 Warranty EXTECH INSTRUMENTS CORPORATION (a FLIR company) warrants this instrument to be free of defects in parts and workmanship for one year from date of shipment (a six month limited warranty applies on sensors and cables). If it should become necessary to return the instrument for service during or beyond the warranty period, contact the Customer Service Department at (781) 890-7440 ext. 210 for authorization or visit our website at www.extech.com (click on Contact Extech and go to Service Department to request an RA number). A Return Authorization (RA) number must be issued before any product is returned to Extech. The sender is responsible for shipping charges, freight, insurance and proper packaging to prevent damage in transit. This warranty does not apply to defects resulting from action of the user such as misuse, improper wiring, operation outside of specification, improper maintenance or repair, or unauthorized modification. Extech specifically disclaims any implied warranties or merchantability or fitness for a specific purpose and will not be liable for any direct, indirect, incidental or consequential damages. Extech's total liability is limited to repair or replacement of the product. The warranty set forth above is inclusive and no other warranty, whether written or oral, is expressed or implied. Copyright © 2008 Extech Instruments Corporation (a FLIR company) All rights reserved including the right of reproduction in whole or in part in any form. 7 RT30 V2.0 11/08