6N136M

PRELIMINARY Single-Channel: 6N135M, 6N136M, HCPL2503M, HCPL4502M, HCPL4503M Dual-Channel: HCPL2530M, HCPL2531M — High Speed Transistor Optocouplers October 2008 Single-Channel: 6N135M, 6N136M, HCPL2503M, HCPL4502M, HCPL4503M Dual-Channel: HCPL2530M, HCPL2531M High Speed Transistor Optocouplers Features ■ High speed –1 MBit/s ■ Superior CMR – 10kV/µs ■ Dual-Channel HCPL2530M, HCPL2531M ■ ■ ■ ■ ■ ■ Description The HCPL4502M, HCPL4503M, HCPL2503M, 6N135M, 6N136M, HCPL2530M and HCPL2531M optocouplers consist of an AlGaAs LED optically coupled to a high speed photodetector transistor. A separate connection for the bias of the photodiode improves the speed by several orders of magnitude over conventional phototransistor optocouplers by reducing the base-collector capacitance of the input transistor. An internal noise shield provides superior common mode rejection of up to 50,000V/µs. (Preliminary) CTR guaranteed 0–70°C U.L. recognized (File # E90700, Vol. 2) 5,000Vrms (1 minute) isolation rating Superior CMR of 15,000V/µs min. (HCPL4503M) >8mm creepage and clearance (option T) No base connection for improved noise immunity (HCPL4502M, HCPL4503M) Applications ■ Line receivers ■ Pulse transformer replacement ■ Output interface to CMOS-LSTTL-TTL ■ Wide bandwidth analog coupling Schematics Package Outlines N/C 1 8 VCC +1 V F1 8 VCC 8 1 +2 V F 7 VB _ 2 7 V01 8 8 1 1 _ 3 6 VO _ V 3 6 V02 F2 N/C 4 5 GND +4 5 GND 6N135M, 6N136M, HCPL2503M, HCPL4502M, HCPL4503M Pin 7 is not connected in HCPL4502M and HCPL4503M ©2008 Fairchild Semiconductor Corporation 6N13XM, HCPLXXXM Rev. 1.0.1 HCPL2530M/HCPL2531M www.fairchildsemi.com PRELIMINARY Single-Channel: 6N135M, 6N136M, HCPL2503M, HCPL4502M, HCPL4503M Dual-Channel: HCPL2530M, HCPL2531M — High Speed Transistor Optocouplers Absolute Maximum Ratings (TA = 25°C unless otherwise specified) Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. The absolute maximum ratings are stress ratings only. Symbol TSTG TOPR TSOL EMITTER IF (avg) IF (pk) IF (trans) VR PD DC/Average Forward Input Current Each Channel(1) Peak Forward Input Current Each Channel(2) Peak Transient Input Current Each Channel Reverse Input Voltage Each Channel Input Power Dissipation Each Channel 6N135M, 6N136M, HCPL2503M, HCPL4502M, HCPL4503M HCPL2530M, HCPL2531M(3) DETECTOR IO (avg) IO (pk) VEBR VCC VO IB PD Average Output Current Each Channel Peak Output Current Each Channel Emitter-Base Reverse Voltage Supply Voltage Output Voltage Base Current Output Power Dissipation Each Channel 6N135M, 6N136M and HCPL2503M only 6N135M, 6N136M, HCPL2503M, HCPL4502M, HCPL4503M(4) HCPL2530M, HCPL2531M Notes: 1. Derate linearly above 70°C free-air temperature at a rate of 0.8mA/°C. 2. Derate linearly above 70°C free-air temperature at a rate of 1.6mA/°C. 3. Derate linearly above 70°C free-air temperature at a rate of 0.9 mW/°C. 4. Derate linearly above 70°C free-air temperature at a rate of 2.0 mW/°C. 6N135M, 6N136M and HCPL2503M only 8 16 5 -0.5 to 30 -0.5 to 20 5 100 35 mA mA V V V mA mW mW 50% duty cycle, 1ms P.W. ≤1µs P.W., 300pps 25 50 1.0 5 100 45 mA mA A V mW Parameter Storage Temperature Operating Temperature Lead Solder Temperature (Wave) Condition Value -40 to +125 -40 to +100 260 for 10 sec Units °C °C °C ©2008 Fairchild Semiconductor Corporation 6N13XM, HCPLXXXM Rev. 1.0.1 www.fairchildsemi.com 2 PRELIMINARY Single-Channel: 6N135M, 6N136M, HCPL2503M, HCPL4502M, HCPL4503M Dual-Channel: HCPL2530M, HCPL2531M — High Speed Transistor Optocouplers Electrical Characteristics (TA = 0 to 70°C Unless otherwise specified) Individual Component Characteristics Symbol EMITTER VF BVR Input Forward Voltage Input Reverse Breakdown Voltage IF = 16mA, TA =25°C IF = 16mA IR = 10 µA IF = 16mA All All All All 5.0 -1.6 1.45 1.7 1.8 V mV/°C V Parameter Test Conditions Device Min. Typ.* Max. Unit ∆VF/∆TA Temperature Coefficient of Forward Voltage DETECTOR IOH Logic High Output Current IF = 0mA, VO = VCC = 5.5V, TA =25°C IF = 0mA, VO = VCC = 15V, TA =25°C All 6N135M 6N136M HCPL4502M HCPL4503M HCPL2503M All 6N135M 6N136M HCPL4502M HCPL4503M HCPL2503M HCPL2530M HCPL2531M 6N135M 6N136M HCPL4502M HCPL4503M HCPL2503M 6N135M 6N136M HCPL4502M HCPL4503M HCPL2503M HCPL2530M HCPL2531M 0.003 0.005 0.5 1 µA IF = 0mA, VO = VCC = 15V ICCL Logic Low Supply Current IF = 16mA, VO = Open, VCC = 15V 50 145 200 µA IF1 = IF2 = 16mA, VO = Open, VCC = 15V ICCH Logic High Supply Current IF = 0mA, VO = Open, VCC = 15V, TA =25°C 250 400 1 µA IF = 0mA, VO = Open, VCC = 15V 2 IF = 0mA, VO = Open, VCC = 15V *All Typicals at TA = 25°C 0.02 4 ©2008 Fairchild Semiconductor Corporation 6N13XM, HCPLXXXM Rev. 1.0.1 www.fairchildsemi.com 3 PRELIMINARY Single-Channel: 6N135M, 6N136M, HCPL2503M, HCPL4502M, HCPL4503M Dual-Channel: HCPL2530M, HCPL2531M — High Speed Transistor Optocouplers Electrical Characteristics (Continued) (TA = 0 to 70°C unless otherwise specified) Transfer Characteristics Symbol COUPLED CTR Current Transfer Ratio(5) IF = 16mA, VO = 0.4 V, VCC = 4.5V, TA =25°C 6N135M HCPL2530M 6N136M HCPL4502M HCPL4503M HCPL2531M HCPL2503M IF = 16mA, VCC = 4.5V VOL = 0.4V VOL = 0.5V VOL = 0.4V 6N135M HCPL2530M 6N136M HCPL4502M HCPL4503M HCPL2531M HCPL2503M 6N135M HCPL2530M 6N136M HCPL2503M HCPL4503M HCPL2531M IF = 16mA, IO = 0.8mA, VCC = 4.5V IF = 16mA, IO = 2.4mA, VCC = 4.5V *All Typicals at TA = 25°C Note: 5. Current Transfer Ratio is defined as a ratio of output collector current, IO, to the forward LED input current, IF, times 100%. 6N135M HCPL2530M HCPL4502M HCPL4503M HCPL2531M 9 30 0.10 0.10 0.15 0.4 0.5 0.4 % V 15 30 % 7 19 18 30 50 50 % % Parameter Test Conditions Device Min. Typ.* Max. Unit 12 5 27 21 % % VOL = 0.5V VOL = 0.4V VOL Logic LOW Output Voltage IF = 16mA, IO = 1.1mA, VCC = 4.5V, TA =25°C IF = 16mA, IO = 3mA, VCC = 4.5V, TA =25°C 0.15 0.5 0.5 0.5 ©2008 Fairchild Semiconductor Corporation 6N13XM, HCPLXXXM Rev. 1.0.1 www.fairchildsemi.com 4 PRELIMINARY Single-Channel: 6N135M, 6N136M, HCPL2503M, HCPL4502M, HCPL4503M Dual-Channel: HCPL2530M, HCPL2531M — High Speed Transistor Optocouplers Electrical Characteristics (Continued) (TA = 0 to 70°C unless otherwise specified) Switching Characteristics (VCC = 5V) Symbol Parameter TPHL Propagation Delay Time to Logic LOW Test Conditions TA = 25°C, RL = 4.1kΩ, IF = 16mA(6) (Fig. 7) RL = 1.9kΩ, IF = 16mA, TA = 25°C(7) (Fig. 7) Device 6N135M HCPL2530M 6N136M HCPL4502M HCPL4503M HCPL2503M HCPL2531M 6N135M HCPL2530M 6N136M HCPL4502M HCPL4503M HCPL2503M HCPL2531M 6N135M HCPL2530M 6N136M HCPL4502M HCPL4503M HCPL2503M HCPL2531M 6N135M HCPL2530M 6N136M HCPL4502M HCPL4503M HCPL2503M HCPL2531M 6N135M HCPL2530M 6N136M HCPL4502M HCPL2503M HCPL2531M HCPL4503M 6N135M HCPL2530M 6N136M HCPL4502M HCPL2503M HCPL2531M Min. Typ.* 0.45 0.45 Max. 1.5 0.8 Unit µs µs RL = 4.1kΩ, IF = 16mA(6) (Fig. 7) RL = 1.9kΩ, IF = 16mA(7) (Fig. 7) 2.0 1.0 µs µs TPLH Propagation Delay Time to Logic HIGH TA = 25°C, (RL = 4.1kΩ, IF = 16mA(6) (Fig. 7) RL = 1.9kΩ, IF = 16mA(7) (Fig. 7) TA = 25°C 0.5 0.3 1.5 0.8 µs µs RL = 4.1kΩ, IF = 16mA(6) (Fig. 7) RL = 1.9kΩ, IF = 16mA(7) (Fig. 7) 2.0 1.0 µs µs |CMH| Common Mode Transient Immunity at Logic High IF = 0mA, VCM = 10VP-P, RL = 4.1kΩ, TA = 25°C(8) (Fig. 8) IF = 0mA, VCM = 10VP-P, RL = 1.9kΩ, TA = 25°C(8) (Fig. 8) 10,000 10,000 V/µs V/µs IF = 0mA, VCM = 1,500VP-P, RL = 1.9kΩ, TA = 25°C(8) (Fig. 8) |CML| Common Mode Transient Immunity at Logic Low IF = 16mA, VCM = 10VP-P, RL = 4.1kΩ, TA = 25°C(8) (Fig. 8) IF = 16mA, VCM = 10VP-P, RL = 1.9kΩ(8) (Fig. 8) 15,000 30,000 10,000 10,000 V/µs V/µs IF = 0mA, VCM = 1,500VP-P, RL = 1.9kΩ, TA = 25°C(8) (Fig. 8) ** All Typicals at TA = 25°C HCPL4503M 15,000 30,000 Notes: 6. The 4.1kΩ load represents 1 LSTTL unit load of 0.36mA and 6.1kΩ pull-up resistor. 7. The 1.9kΩ load represents 1 TTL unit load of 1.6mA and 5.6kΩ pull-up resistor. 8. Common mode transient immunity in logic high level is the maximum tolerable (positive) dVcm/dt on the leading edge of the common mode pulse signal VCM, to assure that the output will remain in a logic high state (i.e., VO > 2.0V). Common mode transient immunity in logic low level is the maximum tolerable (negative) dVcm/dt on the trailing edge of the common mode pulse signal, VCM, to assure that the output will remain in a logic low state (i.e., VO < 0.8V). ©2008 Fairchild Semiconductor Corporation 6N13XM, HCPLXXXM Rev. 1.0.1 www.fairchildsemi.com 5 PRELIMINARY Single-Channel: 6N135M, 6N136M, HCPL2503M, HCPL4502M, HCPL4503M Dual-Channel: HCPL2530M, HCPL2531M — High Speed Transistor Optocouplers Electrical Characteristics (Continued) (TA = 0 to 70°C unless otherwise specified) Isolation Characteristics (TA = 0 to 70°C Unless otherwise specified) Symbol VISO RI-O CI-O HFE II-I RI-I CI-I Characteristics Withstand Insulation Test Voltage Resistance (Input to Output) DC Current Gain Input-Input Insulation Leakage Current Input-Input Resistance Input-Input Capacitance Test Conditions RH ≤ 50%, TA = 25°C, II-O ≤ 10µA, t = 1 min., f = 50Hz(9)(11) VI-O = 500VDC(9) 0V(9) 500VDC(10) IO = 3mA, VO = 5V(9) RH ≤ 45%, VI-I = t = 5 s, (HCPL2530M/2531M only) VI-I = 500 VDC(10) (HCPL2530M/2531M only) f = 1MHz(10) (HCPL2530M/2531M only) Min 5,000 Typ** Max Unit VRMS 1011 1 150 0.005 1011 0.03 Ω pF µA Ω pF Capacitance (Input to Output) f = 1MHz, VI-O = Notes: 9. Device is considered a two terminal device: Pins 1, 2, 3 and 4 are shorted together and Pins 5, 6, 7 and 8 are shorted together. 10. Measured between pins 1 and 2 shorted together, and pins 3 and 4 shorted together. 11. 5,000Vrms for 1 minute duration is equivalent to 6,000Vrms for 1 second duration. ©2008 Fairchild Semiconductor Corporation 6N13XM, HCPLXXXM Rev. 1.0.1 www.fairchildsemi.com 6 PRELIMINARY Single-Channel: 6N135M, 6N136M, HCPL2503M, HCPL4502M, HCPL4503M Dual-Channel: HCPL2530M, HCPL2531M — High Speed Transistor Optocouplers Typical Performance Curves Fig. 1 Normalized CTR vs. Forward Current 1.2 1.2 Fig. 2 Normalized CTR vs. Temperature 1.0 1.0 NORMALIZED CTR 0.8 NORMALIZED CTR 0.8 0.6 0.6 0.4 Normalized to: IF = 16 mA 0.2 VO = 0.4 V VCC = 5 V TA = 25°C 0.4 Normalized to: TA = 25°C 0.2 IF = 16mA VCC = 4.5V VO = 0.4V 0.0 0.1 1 10 100 0.0 -40 -20 0 20 40 60 80 100 IF - FORWARD CURRENT (mA) TA - TEMPERATURE (°C) Fig. 3 Output Current vs. Output Voltage TA = 25°C VCC = 5 V Fig. 4 Logic High Output Current vs. Temperature IOH – LOGIC HIGH OUTPUT CURRENT (nA) 100 IF = 0 mA VCC = 5.5V VO = 5.5V 18 16 IO – OUTPUT CURRENT (mA) IF = 40mA 35mA 14 12 10 8 6 4 2 0 0 2 4 6 8 10 12 14 16 18 20 30mA 25mA 20mA 15mA 10mA 5mA 10 1 0.1 -40 -20 0 20 40 60 80 100 VO – OUTPUT VOLTAGE (V) TA – TEMPERATURE (°C) Fig. 5 Propagation Delay vs. Temperature 800 700 Fig. 6 Propagation Delay vs. Load Resistance Tp – PROPAGATION DELAY (ns) 600 500 400 300 200 100 0 -40 RL = 4.1kΩ (tPLH) TP - PROPAGATION DELAY (ns) 1000 IF = 16mA (tPLH) IF = 10mA (tPHL) RL = 1.9kΩ (tPLH) RL = 1.9kΩ (tPHL) RL = 4.1kΩ (tPHL) Frequency = 10kHz Duty Cycle = 10% IF = 16mA VCC = 5 V IF = 10mA (tPLH) IF = 16mA (tPHL) Frequency = 10kHz Duty Cycle = 10% IF = 16mA VCC = 5 V 10 100 1 -20 0 20 40 60 80 100 TA – TEMPERATURE (°C) RL – LOAD RESISTANCE (kΩ) ©2008 Fairchild Semiconductor Corporation 6N13XM, HCPLXXXM Rev. 1.0.1 www.fairchildsemi.com 7 PRELIMINARY Single-Channel: 6N135M, 6N136M, HCPL2503M, HCPL4502M, HCPL4503M Dual-Channel: HCPL2530M, HCPL2531M — High Speed Transistor Optocouplers Test Circuits 1 + Noise Shield Pulse Generator I F tr = 5ns Z O = 50 Ω 10% D.C. I/f < 100µs 8 7 6 5 VCC +5 V Pulse Generator tr = 5ns Z O = 50 Ω IF + Noise Shield 1 VF1 - 8 7 6 5 VCC RL +5 V 2 VF - VB RL 10% DUTY CYCLE I/f < 100µS VO 2 3 4 V01 VO C L = 1.5 µF 3 I F Monitor Rm VO 0.1 µF IF MONITOR VF2 + Rm V02 0.1 µF 4 GND GND C L = 1.5 µF Test Circuit for HCPL2530M and HCPL2531M Test Circuit for 6N135M, 6N136M, HCPL2503M, HCPL4502M and HCPL4503M IF 0 VO 5V 1.5 V 1.5 V VOL TPHL TPLH Fig. 7 Switching Time Test Circuit IF 1 + Noise Shield 8 7 6 5 VCC +5 V IF + VF1 A Noise Shield 1 2 3 4 8 7 6 5 VCC RL V01 +5 V 2 A B VFF VF - VB RL VO 3 4 + VCM VO VO 0.1 µF B VFF VF2 + V02 0.1 µF GND - GND - Pulse Gen + VCM - Pulse Gen Test Circuit for 6N135M, 6N136M, HCPL2503M, HCPL4502M and HCPL4503M Test Circuit for HCPL2530M and HCPL2531M VCM 10 V 10% tr 90% 90% 10% tf 0V VO Switch at A : IF = 0 mA VO Switch at A : IF = 16 mA 5V VOL Fig. 8 Common Mode Immunity Test Circuit ©2008 Fairchild Semiconductor Corporation 6N13XM, HCPLXXXM Rev. 1.0.1 www.fairchildsemi.com 8 PRELIMINARY Single-Channel: 6N135M, 6N136M, HCPL2503M, HCPL4502M, HCPL4503M Dual-Channel: HCPL2530M, HCPL2531M — High Speed Transistor Optocouplers Package Dimensions Through Hole PIN 1 ID. 4 3 2 1 4 3 2 1 0.4" Lead Spacing PIN 1 ID. 0.270 (6.86) 0.250 (6.35) 5 6 7 8 0.270 (6.86) 0.250 (6.35) 0.390 (9.91) 0.370 (9.40) 5 6 7 8 SEATING PLANE 0.070 (1.78) 0.045 (1.14) 0.200 (5.08) 0.140 (3.55) 0.020 (0.51) MIN SEATING PLANE 0.390 (9.91) 0.370 (9.40) 0.070 (1.78) 0.045 (1.14) 0.200 (5.08) 0.140 (3.55) 0.004 (0.10) MIN 0.154 (3.90) 0.120 (3.05) 0.022 (0.56) 0.016 (0.41) 0.100 (2.54) TYP 0.016 (0.40) 0.008 (0.20) 15° MAX 0.300 (7.62) TYP 0.154 (3.90) 0.120 (3.05) 0.022 (0.56) 0.016 (0.41) 0.100 (2.54) TYP 0.016 (0.40) 0.008 (0.20) 0° to 15° 0.400 (10.16) TYP Surface Mount 0.390 (9.91) 0.370 (9.40) 4 3 2 1 8-Pin DIP – Land Pattern (option S) 0.070 (1.78) PIN 1 ID. 0.270 (6.86) 0.250 (6.35) 0.060 (1.52) 5 6 7 8 0.100 (2.54) 0.295 (7.49) 0.415 (10.54) 0.030 (0.76) 0.070 (1.78) 0.045 (1.14) 0.020 (0.51) MIN 0.300 (7.62) TYP 0.016 (0.41) 0.008 (0.20) 0.022 (0.56) 0.016 (0.41) 0.100 (2.54) TYP Lead Coplanarity : 0.004 (0.10) MAX 0.045 [1.14] 0.315 (8.00) MIN 0.405 (10.30) MAX. Note: All dimensions are in inches (millimeters) Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild’s worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products. Always visit Fairchild Semiconductor’s online packaging area for the most recent package drawings: http://www.fairchildsemi.com/packaging/ ©2008 Fairchild Semiconductor Corporation 6N13XM, HCPLXXXM Rev. 1.0.1 www.fairchildsemi.com 9 PRELIMINARY Single-Channel: 6N135M, 6N136M, HCPL2503M, HCPL4502M, HCPL4503M Dual-Channel: HCPL2530M, HCPL2531M — High Speed Transistor Optocouplers Ordering Information Option No option S SD T V TV SV SDV Example Part Number 6N135M 6N135SM 6N135SDM 6N135TM 6N135VM 6N135TVM 6N135SVM 6N135SDVM Description Standard through hole lead form Surface mount lead bend Surface mount; tape and reel 0.4" lead spacing IEC60747-5-2 (approval pending) IEC60747-5-2 (approval pending); 0.4" lead spacing IEC60747-5-2 (approval pending); surface mount IEC60747-5-2 (approval pending); surface mount; tape and reel Marking Information 1 2503 V 3 4 2 6 XX YY 5 B Definitions 1 2 3 4 5 6 Fairchild logo Device number IEC60747-5-2 mark (Note: Only appears on parts ordered with this option – See order entry table) Two digit year code, e.g., ‘08’ Two digit work week ranging from ‘01’ to ‘53’ Assembly package code ©2008 Fairchild Semiconductor Corporation 6N13XM, HCPLXXXM Rev. 1.0.1 www.fairchildsemi.com 10 PRELIMINARY Single-Channel: 6N135M, 6N136M, HCPL2503M, HCPL4502M, HCPL4503M Dual-Channel: HCPL2530M, HCPL2531M — High Speed Transistor Optocouplers Carrier Tape Specifications D0 K0 t P0 P2 E A0 W1 B0 F W d User Direction of Feed P D1 Symbol W t P0 D0 E F P2 P A0 B0 K0 W1 d R Pocket Pitch Tape Width Description Tape Thickness Sprocket Hole Pitch Sprocket Hole Diameter Sprocket Hole Location Pocket Location Dimension in mm 16.0 ± 0.3 0.30 ± 0.05 4.0 ± 0.1 1.55 ± 0.05 1.75 ± 0.10 7.5 ± 0.1 2.0 ± 0.1 12.0 ± 0.1 10.30 ±0.20 10.30 ±0.20 4.90 ±0.20 Pocket Dimensions Cover Tape Width Cover Tape Thickness Max. Component Rotation or Tilt Min. Bending Radius 13.2 ± 0.2 0.1 max 10° 30 ©2008 Fairchild Semiconductor Corporation 6N13XM, HCPLXXXM Rev. 1.0.1 www.fairchildsemi.com 11 PRELIMINARY Single-Channel: 6N135M, 6N136M, HCPL2503M, HCPL4502M, HCPL4503M Dual-Channel: HCPL2530M, HCPL2531M — High Speed Transistor Optocouplers Reflow Profile 300 Temperature (°C) 250 200 150 100 50 0 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 Time (Minute) • Peak reflow temperature: 260 C (package surface temperature) • Time of temperature higher than 183 C for 160 seconds or less • One time soldering reflow is recommended Time above 183C,