74C86

MM74C86 Quad 2-Input EXCLUSIVE-OR Gate October 1987 Revised January 1999 MM74C86 Quad 2-Input EXCLUSIVE-OR Gate General Description The MM74C86 employs complementary MOS (CMOS) transistors to achieve wide power supply operating range, low power consumption and high noise margin these gates provide basic functions used in the implementation of digital integrated circuit systems. The N- and P-channel enhancement mode transistors provide a symmetrical circuit with output swing essentially equal to the supply voltage. No DC power other than that caused by leakage current is consumed during static condition. All inputs are protected from damage due to static discharge by diode clamps to VCC and GND. Features s Wide supply voltage range: s Guaranteed noise margin: s High noise immunity: 3.0V to 15V 1.0V 0.45 VCC (typ.) s Low power: TTL compatibility: Fan out of 2 driving 74L s Low power consumption: 10 nW/package (typ.) s The MM74C86 follows the MM74LS86 Pinout Ordering Code: Order Number MM74C86M MM74C86N Package Number M14A N14A Package Description 14-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-120, 0.150” Narrow 14-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300” Wide Device also available in Tape and Reel. Specify by appending suffix letter “X” to the ordering code. Connection Diagram Pin Assignments for DIP and SOIC Truth Table Inputs A L L H H H = HIGH Level L = LOW Level Output B L H L H Y L H H L Top View © 1999 Fairchild Semiconductor Corporation DS005887.prf www.fairchildsemi.com MM74C86 Absolute Maximum Ratings(Note 1) Voltage at any Pin (Note 1) Operating Temperature Range Storage Temperature Range Power Dissipation (PD) Dual-In-Line Package Small Outline Operating Range (VCC) 700 mW 500 mW 3.0V to 15V −0.3V to VCC + 0.3V −40°C to +85°C −65°C to +150°C Absolute Maximum (VCC) Lead Temperature (Soldering, 10 seconds) 18V 260°C Note 1: “Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be guaranteed. Except for “Operating Temperature Range” they are not meant to imply that the devices should be operated at these limits. The Electrical Characteristics table provides conditions for actual device operation. DC Electrical Characteristics Min/max limits apply across temperature range unless otherwise noted Symbol CMOS TO CMOS VIN(1) VIN(0) VOUT(1) VOUT(0) IIN(1) IIN(0) ICC VIN(1) VIN(0) VOUT(1) VOUT(0) ISOURCE ISOURCE ISINK ISINK Logical “1” Input Voltage Logical “0” Input Voltage Logical “1” Output Voltage Logical “0” Output Voltage Logical “1” Input Current Logical “0” Input Current Supply Current Logical “1” Input Voltage Logical “0” Input Voltage Logical “1” Output Voltage Logical “0” Output Voltage Output Source Current (P-Channel) Output Source Current (P-Channel) Output Sink Current (N-Channel) Output Sink Current (N-Channel) VCC = 5.0V VCC = 10V VCC = 5.0V VCC = 10V VCC = 5.0V, IO = −10 µA VCC = 10V, IO = −10 µA VCC = 5.0V, IO = +10 µA VCC = 10V, IO = +10 µA VCC = 15V, VIN = 15V VCC = 15V, VIN = 0V VCC = 15V VCC = 4.75V VCC = 4.75V VCC = 4.75V, IO = −360 µA VCC = 4.75V, IO = 360 µA VCC = 5.0V, VOUT = 0V TA = 25°C VCC = 10V, VOUT = 0V TA = 25°C VCC = 5.0V, VOUT = VCC TA = 25°C VCC = 10V, VOUT = VCC TA = 25°C 8.0 16 mA 1.75 3.6 mA −8.0 −15 mA −1.75 −3.3 2.4 0.4 VCC−1.5 0.8 −1.0 0.005 −0.005 0.01 15 4.5 9.0 0.5 1.0 1.0 3.5 8.0 1.5 2.0 V V V V V V V V µA µA µA V V V V mA Parameter Conditions Min Typ Max Units CMOS/LPTTL INTERFACE OUTPUT DRIVE (See Family Characteristics Data Sheet) (Short Circuit Current) AC Electrical Characteristics (Note 2) TA = 25°C, CL = 50 pF, unless otherwise specified Symbol tpd CIN CPD Parameter Propagation Time to Logical “1” or “0” Input Capacitance Power Dissipation Capacitance VCC = 5.0V VCC = 10V (Note 3) Per Gate (Note 4) Conditions Min Typ 110 50 5.0 20 Max 185 90 Units ns ns pF pF Note 2: AC Parameters are guaranteed by DC correlated testing. Note 3: Capacitance is guaranteed by periodic testing. Note 4: CPD determines the no load AC power consumption of any CMOS device. For complete explanation see Family Characteristics Application Note— AN-90. www.fairchildsemi.com 2 MM74C86 Typical Performance Characteristics Propagation Delay Time vs Load Capacitance Test Circuits and Waveforms Delays Measured with Input tr, tf = 20 ns FIGURE 1. AC Test Circuit FIGURE 2. Switching Time Waveforms 3 www.fairchildsemi.com MM74C86 Physical Dimensions inches (millimeters) unless otherwise noted 14-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-120, 0.150” Narrow Package Number M14A www.fairchildsemi.com 4 MM74C86 Quad 2-Input EXCLUSIVE-OR Gate Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 14-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300” Wide Package Number N14A LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 2. A critical component in any component of a life support 1. Life support devices or systems are devices or systems device or system whose failure to perform can be reawhich, (a) are intended for surgical implant into the sonably expected to cause the failure of the life support body, or (b) support or sustain life, and (c) whose failure device or system, or to affect its safety or effectiveness. to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the www.fairchildsemi.com user. Fairchild does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and Fairchild reserves the right at any time without notice to change said circuitry and specifications.