74F190PC

74F190 Up/Down Decade Counter with Preset and Ripple Clock April 1988 Revised July 1999 74F190 Up/Down Decade Counter with Preset and Ripple Clock General Description The 74F190 is a reversible BCD (8421) decade counter featuring synchronous counting and asynchronous presetting. The preset feature allows the 74F190 to be used in programmable dividers. The Count Enable input, the Terminal Count output and the Ripple Clock output make possible a variety of methods of implementing multistage counters. In the counting modes, state changes are initiated by the rising edge of the clock. Features s High-speed—125 MHz typical count frequency s Synchronous counting s Asynchronous parallel load s Cascadable Ordering Code: Order Number 74F190SC 74F190PC Package Number M16A N16E Package Description 16-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-012, 0.150 Narrow 16-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300 Wide Devices also available in Tape and Reel. Specify by appending the suffix letter “X” to the ordering code. Logic Symbols Connection Diagram IEEE/IEC © 1999 Fairchild Semiconductor Corporation DS009494 www.fairchildsemi.com 74F190 Unit Loading/Fan Out U.L. Pin Names CE CP P0–P3 PL U/D Q0–Q3 RC TC Description HIGH/LOW Count Enable Input (Active LOW) Clock Pulse Input (Active Rising Edge) Parallel Data Inputs Asynchronous Parallel Load Input (Active LOW) Up/Down Count Control Input Flip-Flop Outputs Ripple Clock Output (Active LOW) Terminal Count Output (Active HIGH) 1.0/3.0 1.0/1.0 1.0/1.0 1.0/1.0 1.0/1.0 50/33.3 50/33.3 50/33.3 Input IIH/IIL Output IOH/IOL 20 µA/−1.8 mA 20 µA/−0.6 mA 20 µA/−0.6 mA 20 µA/−0.6 mA 20 µA/−0.6 mA −1 mA/20 mA −1 mA/20 mA −1 mA/20 mA Functional Description The 74F190 is a synchronous up/down BCD decade counter containing four edge-triggered flip-flops, with internal gating and steering logic to provide individual preset, count-up and count-down operations. It has an asynchronous parallel load capability permitting the counter to be preset to any desired number. When the Parallel Load (PL) input is LOW, information present on the Parallel Data inputs (P0–P3) is loaded into the counter and appears on the Q outputs. This operation overrides the counting functions, as indicated in the Mode Select Table. A HIGH signal on the CE input inhibits counting. When CE is LOW, internal state changes are initiated synchronously by the LOWto-HIGH transition of the clock input. The direction of counting is determined by the U/D input signal, as indicated in the Mode Select Table, CE and U/D can be changed with the clock in either state, provided only that the recommended setup and hold times are observed. Two types of outputs are provided as overflow/underflow indicators. The Terminal Count (TC) output is normally LOW and goes HIGH when a circuit reaches zero in the count-down mode or reaches 9 in the count-up mode. The TC output will then remain HIGH until a state change occurs, whether by counting or presetting or until U/D is changed. The TC output should not be used as a clock signal because it is subject to decoding spikes. The TC signal is also used internally to enable the Ripple Clock (RC) output. The RC output is normally HIGH. When CE is LOW and TC is HIGH, the RC output will go LOW when the clock next goes LOW and will stay LOW until the clock goes HIGH again. This feature simplifies the design of multistage counters. For a discussion and illustrations of the various methods of implementing multistage counters, please see the 74F191 data sheet. RC Truth Table Inputs CE L H X TC* H X L Output CP X X H H RC Mode Select Table Inputs PL H H L H CE L L X H U/D L H X X CP Count Up Count Down Preset (Asyn.) No Change (Hold)   X X Mode *TC is generated internally H = H IGH Voltage Level L = LOW Voltage Level X = Immaterial = LOW-to-HIGH Clock Transition = LOW Pulse  www.fairchildsemi.com 2 74F190 State Diagram Logic Diagram Please note that this diagram is provided only for the understanding of logic operations and should not be used to estimate propagation delays. 3 www.fairchildsemi.com 74F190 Absolute Maximum Ratings(Note 1) Storage Temperature Ambient Temperature under Bias Junction Temperature under Bias VCC Pin Potential to Ground Pin Input Voltage (Note 2) Input Current (Note 2) Voltage Applied to Output in HIGH State (with VCC = 0V) Standard Output 3-STATE Output Current Applied to Output in LOW State (Max) twice the rated IOL (mA) −0.5V to VCC −0.5V to +5.5V −65°C to +150°C −55°C to +125°C −55°C to +150°C −0.5V to +7.0V −0.5V to +7.0V −30 mA to +5.0 mA Recommended Operating Conditions Free Air Ambient Temperature Supply Voltage 0°C to +70°C +4.5V to +5.5V Note 1: Absolute maximum ratings are values beyond which the device may be damaged or have its useful life impaired. Functional operation under these conditions is not implied. Note 2: Either voltage limit or current limit is sufficient to protect inputs. DC Electrical Characteristics Symbol VIH VIL VCD VOH VOL IIH IBVI ICEX VID IOD IIL Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Voltage Output LOW Voltage Input HIGH Current Input HIGH Current Breakdown Test Output HIGH Leakage Current Input Leakage Test Output Leakage Circuit Current Input LOW Current −60 38 4.75 3.75 −0.6 −1.8 IOS ICCL Output Short-Circuit Current Power Supply Current −150 55 mA mA Max Max 10% VCC 5% VCC 10% VCC 2.5 2.7 0.5 5.0 7.0 50 Min 2.0 0.8 −1.2 Typ Max Units V V V V V µA µA µA V µA mA Min Min Min Max Max Max 0.0 0.0 Max VCC Conditions Recognized as a HIGH Signal Recognized as a LOW Signal IIN = −18 mA IOH = −1 mA IOH = −1 mA IOL = 20 mA VIN = 2.7V VIN = 7.0V VOUT = VCC IID = 1.9 µA All Other Pins Grounded VIOD = 150 mV All Other Pins Grounded VIN = 0.5V, except CE VIN = 0.5V, CE VOUT = 0V VO = LOW www.fairchildsemi.com 4 74F190 AC Electrical Characteristics TA = +25°C Symbol Parameter Min fMAX tPLH tPHL tPLH tPHL tPLH tPHL tPLH tPHL tPLH tPHL tPLH tPHL tPLH tPHL tPLH tPHL Maximum Clock Frequency Propagation Delay CP to Qn Propagation Delay CP to TC Propagation Delay CP to RC Propagation Delay CE to RC Propagation Delay U /D to RC Propagation Delay U /D to TC Propagation Delay P n t o Qn Propagation Delay PL to Qn 100 3.0 5.0 6.0 5.0 3.0 3.0 3.0 3.0 7.0 5.5 4.0 4.0 3.0 6.0 5.0 5.5 VCC = +5.0V CL = 50 pF Typ 125 5.5 8.5 10.0 8.5 5.5 5.0 5.0 5.5 11.0 9.0 7.0 6.5 4.5 10.0 8.5 9.0 7.5 11.0 13.0 11.0 7.5 7.0 7.0 7.0 18.0 12.0 10.0 10.0 7.0 13.0 11.0 12.0 Max TA −55°C to +125°C VCC = +5.0V CL = 50 pF Min 75 3.0 5.0 6.0 5.0 3.0 3.0 3.0 3.0 7.0 5.5 4.0 4.0 3.0 6.0 5.0 5.5 9.5 13.5 16.5 13.5 9.5 9.0 9.0 9.0 22.0 14.0 13.5 12.5 9.0 16.0 13.0 14.5 Max TA = 0°C to +70°C VCC = +5.0V CL = 50 pF Min 90 3.0 5.0 6.0 5.0 3.0 3.0 3.0 3.0 7.0 5.5 4.0 4.0 3.0 6.0 5.0 5.5 8.5 12.0 14.0 12.0 8.5 8.0 8.0 8.0 20.0 13.0 11.0 11.0 8.0 14.0 12.0 13.0 ns ns ns ns ns Max MHz Units AC Operating Requirements TA = +25°C Symbol Parameter VCC = +5.0V Min tS(H) tS(L) tH(H) tH(L) tS(L) tH(L) tS(H) tS(L) tH(H) tH(L) tW(L) tW(L) tREC Setup Time, HIGH or LOW Pn to PL Hold Time, HIGH or LOW Pn to PL Setup Time, LOW CE to CP Hold Time, LOW CE to CP Setup Time, HIGH or LOW U /D to CP Hold Time, HIGH or LOW U /D to CP PL Pulse Width, LOW CP Pulse Width, LOW Recovery Time PL to CP 12.0 12.0 0 0 6.0 5.0 6.0 12.0 12.0 0 0 8.5 7.0 7.5 12.0 12.0 0 0 6.0 5.0 6.0 ns ns ns ns 0 0 0 4.5 4.5 2.0 2.0 10.0 Max TA −55°C to +125°C VCC = +5.0V Min 6.0 6.0 2.0 2.0 10.5 Max TA = 0°C to +70°C VCC = +5.0V Min 5.0 5.0 2.0 2.0 10.0 ns Max ns Units 5 www.fairchildsemi.com 74F190 Physical Dimensions inches (millimeters) unless otherwise noted 16-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-012, 0.150 Narrow Package Number M16A www.fairchildsemi.com 6 74F190 Up/Down Decade Counter with Preset and Ripple Clock Physical Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 16-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300 Wide Package Number N16E Fairchild does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and Fairchild reserves the right at any time without notice to change said circuitry and specifications. LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 7 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. www.fairchildsemi.com www.fairchildsemi.com