74VHC4066

74VHC4066 Quad Analog Switch April 1994 Revised January 2000 74VHC4066 Quad Analog Switch General Description These devices are digitally controlled analog switches utilizing advanced silicon-gate CMOS technology. These switches have low “on” resistance and low “off” leakages. They are bidirectional switches, thus any analog input may be used as an output and visa-versa. Also the 4066 switches contain linearization circuitry which lowers the “on” resistance and increases switch linearity. The 4066 devices allow control of up to 12V (peak) analog signals with digital control signals of the same range. Each switch has its own control input which disables each switch when low. All analog inputs and outputs and digital inputs are protected from electrostatic damage by diodes to VCC and ground. Features s Typical switch enable time: 15 ns s Wide analog input voltage range: 0–12V s Low “on” resistance: 30 typ. ('4066) s Low quiescent current: 80 µA maximum (74VHC) s Matched switch characteristics s Individual switch controls s Pin and function compatible with the 74HC4066 Ordering Code: Order Number 74VHC4066M 74VHC4066MTC 74VHC4066N Package Number M14A MTC14 N14A Package Description 14-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-120, 0.150 Narrow 14-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm Wide 14-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300 Wide Surface mount packages are also available on Tape and Reel. Specify by appending the suffix letter “X” to the ordering code. Connection Diagram Schematic Diagram Top View Truth Table Input CTL L H Switch I/O–O/I “OFF” “ON” © 2000 Fairchild Semiconductor Corporation DS011677 www.fairchildsemi.com 74VHC4066 Absolute Maximum Ratings(Note 1) (Note 2) Supply Voltage (VCC) DC Control Input Voltage (VIN) DC Switch I/O Voltage (VIO) Clamp Diode Current (IIK, IOK) DC Output Current, per pin (IOUT) DC VCC or GND Current, per pin (ICC) Storage Temperature Range (TSTG) Power Dissipation (PD) (Note 3) S.O. Package only Lead Temperature (TL) (Soldering 10 seconds) 260°C −0.5 to +15V −1.5 to VCC + 1.5V VEE − 0.5 to VCC + 0.5V ±20 mA ±25 mA ±50 mA −65°C to +150°C 600 mW 500 mW Recommended Operating Conditions Min Supply Voltage (VCC) DC Input or Output Voltage (VIN, VOUT) Operating Temperature Range (TA) Input Rise or Fall Times VCC = 2.0V VCC = 4.5V VCC = 9.0V (tr, tf) 1000 500 400 ns ns ns −40 +85 °C 2 0 Max 12 VCC Units V V Note 1: Absolute Maximum Ratings are those values beyond which damage to the device may occur. Note 2: Unless otherwise specified all voltages are referenced to ground. Note 3: Power Dissipation temperature derating — plastic “N” package: − 12 mW/°C from 65°C to 85°C. DC Electrical Characteristics Symbol VIH Parameter Minimum HIGH Level Input Voltage (Note 4) Conditions VCC 2.0V 4.5V 9.0V 12.0V TA=25°C Typ 1.5 3.15 6.3 8.4 0.5 1.35 2.7 3.6 100 50 30 120 50 35 20 10 5 5 170 85 70 180 80 60 40 15 10 10 ±0.05 6.0V 9.0V 12.0V 6.0V 9.0V 12.0V 6.0V 9.0V 12.0V 10 15 20 10 15 20 ±60 ±80 ±100 ±40 ±50 ±60 1.0 2.0 4.0 TA=−40 to 85°C Guaranteed Limits 1.5 3.15 5.3 8.4 0.5 1.35 2.7 3.6 200 105 85 215 100 75 60 20 15 15 ±0.5 ±600 ±800 ±1000 ±150 ±200 ±300 10 20 40 Units V V V V V V V V Ω Ω Ω Ω Ω Ω Ω Ω Ω Ω µA nA nA nA nA nA nA µA µA µA VIL Maximum LOW Level Input Voltage 2.0V 4.5V 9.0V 12.0V RON Maximum “ON” Resistance See (Note 5) VCTL = VIH, IS = 2.0 mA VIS = V CC to GND (Figure 1) VCTL = VIH, IS = 2.0 mA VIS = V CC or GND (Figure 1) 4.5V 9.0V 12.0V 2.0V 4.5V 9.0V 12.0V 4.5V 9.0V 12.0V RON Maximum “ON” Resistance Matching VCTL = VIH VIS = V CC to GND VIN = VCC or GND VCC = 2 − 6V VOS = V CC or GND VIS = GND or VCC VCTL = VIL (Figure 2) VIS = V CC to GND VCTL = VIH VOS = OPEN (Figure 3) VIN = VCC or GND IOUT = 0 µA IIN IIZ Maximum Control Input Current Maximum Switch “OFF” Leakage Current IIZ Maximum Switch “ON” Leakage Current ICC Maximum Quiescent Supply Current Note 4: For a power supply of 5V ± 10% the worst case on resistance (RON) occurs for VHC at 4.5V. Thus the 4.5V values should be used when designing with this supply. Worst case VIH and VIL occur at VCC = 5.5V and 4.5V respectively. (The VIH value at 5.5V is 3.85V.) The worst case leakage current occurs for CMOS at the higher voltage and so the 5.5V values should be used. Note 5: At supply voltages (VCC – GND) approaching 2V the analog switch on resistance becomes extremely non-linear. Therefore it is recommended that these devices be used to transmit digital only when using these supply voltages. www.fairchildsemi.com 2 74VHC4066 AC Electrical Characteristics VCC = 2.0V−6.0V VEE = 0V−12V, CL = 50 pF (unless otherwise specified) Symbol tPHL, tPLH Parameter Maximum Propagation Delay Switch In to Out Conditions VCC 3.3V 4.5V 9.0V 12.0V tPZL, tPZH Maximum Switch Turn “ON” Delay RL = 1 kΩ 3.3V 4.5V 9.0V 12.0V tPHZ, tPLZ Maximum Switch Turn “OFF” Delay RL = 1 kΩ 3.3V 4.5V 9.0V 12.0V Minimum Frequency Response (Figure 7) 20 log(VO/VI) = −3 dB Crosstalk Between any Two Switches (Figure 8) Peak Control to Switch Feedthrough Noise (Figure 9) Switch OFF Signal Feedthrough Isolation (Figure 10) THD Total Harmonic Distortion (Figure 11) CIN CIN CIN CPD Maximum Control Input Capacitance Maximum Switch Input Capacitance Maximum Feedthrough Capacitance Power Dissipation Capacitance Note 6: Adjust 0 dBm for F = 1 kHz (Null RL/RON Attenuation). Note 7: VIS is centered at VCC/2. Note 8: Adjust input for 0 dBm. TA=25°C Typ 25 5 4 3 30 12 6 5 60 25 20 15 40 100 30 10 8 7 58 20 12 10 100 36 32 30 TA=−40 to 85°C Guaranteed Limits 20 13 10 11 73 25 15 13 125 45 40 38 Units ns ns ns ns ns ns ns ns ns ns ns MHz MHz RL = 600Ω VIS = 2 VPP at (VCC/2) (Note 6)(Note 7) RL = 600Ω, F = 1 MHz (Note 7)(Note 8) RL = 600Ω, F = 1 MHz CL = 50 pF RL = 600Ω, F = 1 MHz V(CT) VIL (Note 7)(Note 8) RL = 10 kΩ, CL = 50 pF, F = 1 kHz VIS = 4 VPP VIS = 8 VPP 4.5V 9.0V 4.5V 9.0V 4.5V 9.0V −52 −50 100 250 dB dB mV mV 4.5V 9.0V −42 −44 dB dB 4.5V 9.0V .013 .008 5 20 10 10 % % pF pF pF pF VCTL = GND 0.5 15 3 www.fairchildsemi.com 74VHC4066 AC Test Circuits and Switching Time Waveforms FIGURE 1. “ON” Resistance FIGURE 2. “OFF” Channel Leakage Current FIGURE 3. “ON” Channel Leakage Current FIGURE 4. tPHL, tPLH Propagation Delay Time Signal Input to Signal Output FIGURE 5. tPZL, tPLZ Propagation Delay Time Control to Signal Output www.fairchildsemi.com 4 74VHC4066 AC Test Circuits and Switching Time Waveforms (Continued) FIGURE 6. tPZH, tPHZ Propagation Delay Time Control to Signal Output FIGURE 7. Frequency Response Crosstalk and Distortion Test Circuits FIGURE 8. Crosstalk: Control Input to Signal Output FIGURE 9. Crosstalk Between Any Two Switches 5 www.fairchildsemi.com 74VHC4066 Crosstalk and Distortion Test Circuits (Continued) FIGURE 10. Switch OFF Signal Feedthrough Isolation FIGURE 11. Sinewave Distortion Typical Performance Characteristics Typical “ON” Resistance Typical Crosstalk Between Any Two Switches Typical Frequency Response Special Considerations In certain applications the external load-resistor current may include both VCC and signal line components. To avoid drawing VCC current when switch current flows into the analog switch input pins, the voltage drop across the switch must not exceed 0.6V (calculated from the ON resistance). www.fairchildsemi.com 6 74VHC4066 Physical Dimensions inches (millimeters) unless otherwise noted 14-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-120, 0.150 Narrow Package Number M14A 7 www.fairchildsemi.com 74VHC4066 Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 14-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm Wide Package Number MTC14 www.fairchildsemi.com 8 74VHC4066 Quad Analog Switch Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 14-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300 Wide Package Number N14A Fairchild does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and Fairchild reserves the right at any time without notice to change said circuitry and specifications. LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 9 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. www.fairchildsemi.com www.fairchildsemi.com