FAN7033MP

www.fairchildsemi.com FAN7033MP 2W Stereo Power Amplifier with Fixed Gain Features • 1.9WRMS and 2.45WRMS Power Per Each Channel Into 4Ω Load With Less Than 1% and 10% THD+N, Respectively • Internally Fixed Gain : 21.6dB(Av=12) • Low Quiescent Current : Typical 5.5mA@5V • Low Shutdown Current : Typical 0.04µA@5V • Fully Differential Input, Which Immunes the Common Mode Noise • Active Low Shutdown Logic • Guaranteed Stability Under No Load Condition • Very Small Volume and Thermally Enhanced SurfaceMount 14MLP Package(4mm*4mm) Description The FAN7033MP is a dual fully differential power amplifier in a thermally enhanced 14-pin MLP package. When delivering 1.9W of continuous RMS power into 4Ω speaker at 5V supply, the FAN7033MP has less than 1% of THD+N over the entire audible frequency range, 20Hz to 20kHz. To save power consumption in the portable applications, the FAN7033MP provides shutdown function. Setting the shutdown pin to ground level, the FAN7033MP falls into shutdown mode and consumes less than 4µA over all supply voltage range, 2.7V to 5.5V. Additional components such as resistors for gain setting and bootstrap capacitors are not needed, making the FAN7033MP well suited for portable sound systems and other hand-held sound equipments. Target applications include the cellular phones, notebook, desktop computers, etc. 14MLP 1 BOTTOM VIEW Typical Applications • Cellular Phones • Notebook Computer • Desktop Computer Internal Block Diagram 90kΩ 15kΩ RIN- 12 15kΩ 15kΩ 13 ROUT+ 10 PVDD1 9 ROUT15kΩ 90kΩ 90kΩ 90kΩ RIN+ 4 11 VDD 7 BYPASS 8 GND SD 14 VDD/2 BIAS & CONTROL 90kΩ 90kΩ 90kΩ 15kΩ LIN+ 6 15kΩ 15kΩ 1 LOUT+ 3 PVDD2 5 LOUT15kΩ 90kΩ LIN- 2 Rev. 1.0.0 ©2003 Fairchild Semiconductor Corporation FAN7033MP Pin Assignments 1 2 3 4 5 6 7 TOP VIEW 14 13 12 11 10 9 8 14 13 12 11 10 9 8 BOTTOM VIEW 1 2 3 4 5 6 7 Pin Descriptions Pin No 1 2 3** 4 5 6 7 8* 9 10** 11** 12 13 14 Symbol LOUT+ LINPVDD2 RIN+ LOUTLIN+ BYPASS GND ROUTPVDD1 VDD RINROUT+ SD I/O O I I I O I O O I I I O I Left Channel (+) Output Left Channel (-) Input Left Channel Power Supply Voltage Right Channel (+) Input Left Channel (-) Output Left Channel (+) Input Bypass Capacitor Connect Ground Right Channel (-) Output Right Channel Power Supply Voltage Power Supply Voltage Right Channel (-) Input Right Channel (+) Output Shutdown Logic Low SD=VDD: Device Enable SD=GND: Device Shutdown Decription * Pin8(GND) and Exposed PAD are internally tied together. **For the best performance, VDD, PVDD1 and PVDD2 must be the same voltage level(strongly recommend). 2 FAN7033MP Absolute Maximum Ratings Parameter Maximum Supply Voltage Power Dissipation Operating Temperature Storage Temperature Junction Temperature Thermal Resistance (Junction to Ambient) ESD Rating (Human Body Model) ESD Rating (Machine Model) * Rthja was derived using the JEDEC boards. Symbol VDDmax PD TOPG TSTG TJmax Rthja* Value 6.0V Internally Limited -40 ~ +85 -65 ~ +150 150 38 145 2000 300 Unit V W °C °C °C °C/W V V Remark Multi-Layer Single-Layer Operating Rating Parameter Power Supply Voltage Symbol VDD Min. 2.7 Typ. Max. 5.5 Unit V 3 FAN7033MP Electrical Characteristics (VDD = 5.0V, Ta = 25°C, unless otherwise specified) Parameter Offset Voltage Supply Current Shutdown Current Output Power Total Harmonic Distortion + Noise Power Supply Rejection Ratio Output Noise Voltage Symbol VOFF IDD ISD PO THD+N PSRR VN Conditions RL=4Ω, Av=21.6dB No Input, No Load SD = GND THD+N =1%, RL = 4Ω, f = 1kHz THD+N =1%, RL = 8Ω, f = 1kHz PO = 1W, RL=4Ω, f = 20kHz Cbyp = 1µF, RL=4Ω, BTL Mode, ∆VDD=500mVpp, f = 1kHz Input=GND, RL=4Ω, f=1kHz Min. -25 38 Typ. 5.5 0.04 1.9 1.25 0.6 68 -120 Max. 25 10 4 Unit mV mA µA W W % dB dBv Electrical Characteristics (VDD = 3.3 V, Ta = 25°C, unless otherwise specified) Parameter Offset Voltage Supply Current Shutdown Current Output Power Total Harmonic Distortion + Noise Power Supply Rejection Ratio Output Noise Voltage Symbol VOFF IDD ISD PO THD+N PSRR VN Conditions RL=4Ω, Av=21.6dB No Input, No Load SD = GND THD+N =1%, RL = 4Ω, f = 1kHz THD+N =1%, RL = 8Ω, f = 1kHz PO = 1W, RL=4Ω, f = 20kHz Cbyp = 1µF, RL=4Ω, BTL Mode, ∆VDD=330mVpp, f = 1kHz Input=GND, RL=4Ω, f=1kHz Min. -25 38 Typ. 4.5 0.04 0.75 0.53 0.75 68 -120 Max. 25 8 4 Unit mV mA µA W W % dB dBv Electrical Characteristics (VDD = 2.7 V, Ta = 25°C, unless otherwise specified) Parameter Offset Voltage Supply Current Shutdown Current Output Power Total Harmonic Distortion + Noise Power Supply Rejection Ratio Output Noise Voltage Symbol VOFF IDD ISD PO THD+N PSRR VN Conditions RL=4Ω, Av=21.6dB No Input, No Load SD = GND THD+N =1%, RL = 4Ω, f = 1kHz THD+N =1%, RL = 8Ω, f = 1kHz PO = 0.5W, RL=4Ω, f = 20kHz Cbyp = 1µF, RL=4Ω, BTL Mode, ∆VDD=270mVpp, f = 1kHz Input=GND, RL=4Ω, f=1kHz Min. -25 36 Typ. 4.1 0.04 0.45 0.32 0.9 62 -120 Max. 25 7 4 Unit mV mA µA W W % dB dBv 4 FAN7033MP Typical Application Circuits Single-Ended Input 90kΩ 1uF RIN- 15kΩ CRINN RIGHT SE INPUT 1uF 12 15kΩ 13 10 9 15kΩ 90kΩ 90kΩ 90kΩ ROUT+ PVDD1 100nF 4Ω RIN+ CRINP 4 15kΩ ROUTVDD BYPASS 1uF RIGHT OUTPUT 11 7 8 ShutDown SD 14 VDD/2 BIAS & CONTROL 90kΩ 90kΩ GND 90kΩ 220uF CLINP 1uF LIN+ 15kΩ 6 15kΩ 1 3 5 15kΩ 90kΩ LOUT+ 100nF LEFT SE INPUT CLINN 1uF LIN- 15kΩ PVDD2 LOUT- 4Ω 2 LEFT OUTPUT 5 FAN7033MP Typical Application Circuits (continued) Differential Input 90kΩ 1uF RIN- 15kΩ CRINN RIGHT DIFF. INPUT 1uF 12 15kΩ 13 10 9 15kΩ 90kΩ 90kΩ 90kΩ ROUT+ PVDD1 100nF 4Ω RIN+ CRINP 4 15kΩ ROUTVDD BYPASS 1uF RIGHT OUTPUT 11 7 8 ShutDown SD 14 VDD/2 BIAS & CONTROL 90kΩ 90kΩ GND 90kΩ 220uF CLINP 1uF LIN+ 15kΩ 6 15kΩ 1 3 5 15kΩ 90kΩ LOUT+ 100nF LEFT DIFF. INPUT CLINN 1uF LIN- 15kΩ PVDD2 LOUT- 4Ω 2 LEFT OUTPUT 6 FAN7033MP Performance Characteristics : Differential Input 10 5 10 5 VDD=5V RL=8Ω Av=21.6dB 2 1 20kHz THD [%] 2 1 0.5 20kHz THD [%] 0.5 1kHz 0.2 0.1 0.05 0.2 0.1 1kHz 20Hz VDD=5V RL=4Ω Av=21.6dB 20m 50m 100m 200m 500m 1 2 3 0.05 20Hz 0.02 0.01 10m 0.02 0.01 10m 20m 50m 100m 200m 500m 1 2 3 Output Power [W] Output Power [W] Figure 1. THD+N vs. Output Power Figure 2. THD+N vs. Output Power 10 5 10 5 2 1 20kHz 2 1 20kHz THD [%] 0.5 THD [%] 1kHz 0.5 1kHz 0.2 0.1 0.05 0.2 0.1 0.05 20Hz 0.02 0.01 10m VDD=3.3V RL=4Ω Av=21.6dB 200m 500m 1 2 3 20Hz 0.02 0.01 10m VDD=3.3V RL=8Ω Av=21.6dB 100m 200m 500m 1 2 3 20m 50m 100m 20m 50m Output Power [W] Output Power [W] Figure 3. THD+N vs. Output Power Figure 4. THD+N vs. Output Power 10 5 10 5 2 1 20kHz 2 1 20kHz THD [%] 0.5 1kHz THD [%] 0.5 1kHz 0.2 0.1 0.05 0.2 0.1 0.05 20Hz 0.02 0.01 10m VDD=2.7V RL=4Ω Av=21.6dB 100m 200m 500m 1 2 3 0.02 0.01 10m 20Hz VDD=2.7V RL=8Ω Av=21.6dB 100m 200m 500m 1 2 3 20m 50m 20m 50m Output Power [W] Output Power [W] Figure 5. THD+N vs. Output Power Figure 6. THD+N vs. Output Power 7 FAN7033MP Performance Characteristics(Continued) 10 5 2 1 0.5 10 5 2 1 0.5 VDD=5V Output power =1W RL=4Ω VDD=5V Output power =1W RL=8Ω THD [%] THD [%] 0.2 0.1 0.05 0.02 0.01 0.005 0.002 0.001 20 50 100 200 500 1k 2k 5k 10k 20k 0.2 0.1 0.05 0.02 0.01 0.005 0.002 0.001 20 50 100 200 500 1k 2k 5k 10k 20k Frequency [Hz] Frequency [Hz] Figure 7. THD+N vs. Frequency Figure 8. THD+N vs. Frequency 10 5 2 1 0.5 10 VDD=3.3V Output power =500mW RL=4Ω 5 2 1 0.5 VDD=3.3V Output power =500mW RL=8Ω THD [%] 0.1 0.05 0.02 0.01 0.005 0.002 0.001 20 50 100 200 500 1k 2k 5k 10k 20k THD [%] 0.2 0.2 0.1 0.05 0.02 0.01 0.005 0.002 0.001 20 50 100 200 500 1k 2k 5k 10k 20k Frequency [Hz] Frequency [Hz] Figure 9. THD+N vs. Frequency Figure 10. THD+N vs. Frequency 10 5 2 1 0.5 10 VDD=2.7V Output power =250mW RL=4Ω 5 2 1 0.5 VDD=2.7V Output power =250mW RL=8Ω THD [%] THD [%] 0.2 0.1 0.05 0.02 0.01 0.005 0.002 0.001 20 50 100 200 500 1k 2k 5k 10k 20k 0.2 0.1 0.05 0.02 0.01 0.005 0.002 0.001 20 50 100 200 500 1k 2k 5k 10k 20k Frequency [Hz] Frequency [Hz] Figure 11. THD+N vs. Frequency Figure 12. THD+N vs. Frequency 8 FAN7033MP Performance Characteristics(Continued) +0 -10 -20 -30 -40 +0 VDD=5V+/-5% RL=4Ω -10 -20 -30 -40 VDD=5V+/-5% RL=8Ω PSRR [dB] -60 -70 -80 -90 -100 -110 -120 20 50 100 200 500 1k 2k 5k 10k 20k PSRR [dB] -50 -50 -60 -70 -80 -90 -100 -110 -120 20 50 100 200 500 1k 2k 5k 10k 20k Frequency [Hz] Frequency [Hz] Figure 13. PSRR vs. Frequency Figure 14. PSRR vs. Frequency +0 -10 -20 -30 -40 +0 VDD=3.3V+/-5% RL=4Ω -10 -20 -30 -40 VDD=3.3V+/-5% RL=8Ω PSRR [dB] -60 -70 -80 -90 -100 -110 -120 20 50 100 200 500 1k 2k 5k 10k 20k PSRR [dB] -50 -50 -60 -70 -80 -90 -100 -110 -120 20 50 100 200 500 1k 2k 5k 10k 20k Frequency [Hz] Frequency [Hz] Figure 15. PSRR vs. Frequency Figure 16. PSRR vs. Frequency +0 -10 -20 -30 -40 +0 VDD=2.7V+/-5% RL=4Ω -10 -20 -30 -40 VDD=2.7V+/-5% RL=8Ω PSRR [dB] PSRR [dB] -50 -60 -70 -80 -90 -100 -110 -120 20 50 100 200 500 1k 2k 5k 10k 20k -50 -60 -70 -80 -90 -100 -110 -120 20 50 100 200 500 1k 2k 5k 10k 20k Frequency [Hz] Frequency [Hz] Figure 17. PSRR vs. Frequency Figure 18. PSRR vs. Frequency 9 FAN7033MP Performance Characteristics(Continued) +0 -10 -20 -30 -40 +0 VDD=5V Output power = 1W RL=4Ω -10 -20 -30 -40 VDD=5V Output power = 1W RL=8Ω Crosstalk [dB] -50 -60 -70 -80 -90 -100 -110 -120 20 50 100 200 500 1k 2k 5k 10k 20k Crosstalk [dB] -50 -60 -70 -80 -90 Left-to-Right Left-to-Right Right-to-Left Right-to-Left -100 -110 -120 20 50 100 200 500 1k 2k 5k 10k 20k Frequency [Hz] Frequency [Hz] Figure 19. Crosstalk vs. Frequency Figure 20. Crosstalk vs. Frequency 7.0m 6.0m 6.0m VDD=5V 5.0m Supply Current [A] 5.0m 4.0m 3.0m 2.0m 1.0m VDD=3.3V Supply Current [A] 4.0m 3.0m 2.0m 1.0m 0.0 VDD=2.7V 0.0 0 1 2 3 4 5 0 1 Supply Voltage [V] 2 3 Shutdown Pin Voltage [V] 4 5 Figure 21. Supply Current vs. Supply Voltage Figure 22. Supply Currrent vs. SD Voltage 1.4 1.2 Power Dissipation [W] VDD=5V 0.7 0.6 Power Dissipation [W] 0.5 0.4 0.3 0.2 0.1 0.0 VDD=5V 1.0 0.8 VDD=3.3V 0.6 0.4 0.2 0.0 VDD=2.7V VDD=3.3V THD less than 1% RL=4 Ω f=1kHz VDD=2.7V THD less than 1% RL=8Ω f=1kHz 0.8 1.0 1.2 1.4 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 0.0 0.2 0.4 0.6 Output Power [W] Output Power [W] Figure 23. Power Dissipation vs. Output Power Figure 24. Power Dissipation vs. Output Power 10 FAN7033MP Performance Characteristics(Continued) 3.0 f=1kHz RL=4Ω 2.0 f=1kHz RL=8 Ω 10% THD+N 1.0 1% THD+N 2.5 Output Power [W] 1.5 2.0 10% THD+N Output Power [W] 1.5 1% THD+N 1.0 0.5 0.5 0.0 2.5 3.0 3.5 4.0 Supply Voltage [V] 4.5 5.0 5.5 0.0 2.5 3.0 3.5 4.0 Supply Voltage [V] 4.5 5.0 5.5 Figure 25. Output Power vs. Supply Voltage Figure 26. Output Power vs. Supply Voltage 1.2 2.0 Output Power [W] VDD=5V f=1kHz Output Power [W] 1.0 VDD=3.3V f=1kHz 10% THD+N 1.5 0.8 10% THD+N 0.6 1.0 1% THD+N 0.5 0.4 1% THD+N 0.2 0.0 0 8 16 24 32 40 48 56 64 0.0 0 8 16 24 32 40 48 56 64 RL-Load Resistance [Ω] RL-Load Resistance [Ω] Figure 27. Output Power vs. Output Load Figure 28. Output Power vs. Output Load 0.7 0.6 0.5 Output Power [W] 100u VDD=2.7V f=1kHz Output Noise Voltage [uV] 50u 20u 10u 5u VDD=5V RL=4Ω Av=21.6dB 0.4 0.3 0.2 0.1 10% THD+N 2u 1u 500n 1% THD+N 200n 0.0 0 8 16 24 32 40 48 56 64 100n 20 50 100 200 500 1k 2k 5k 10k 20k RL-Load Resistance [Ω] Frequency [Hz] Figure 29. Output Power vs. Output Load Figure 30. Outut Noise Voltage vs. Frequency 11 FAN7033MP Performance Characteristics : Single-Ended Input 10 5 10 5 VDD=5V RL=8Ω Av=21.6dB 20kHz 2 1 20kHz THD [%] 2 1 0.5 THD [%] 0.5 1kHz 0.2 0.1 0.05 0.2 0.1 1kHz 20Hz VDD=5V RL=4Ω Av=21.6dB 20m 50m 100m 200m 500m 1 2 3 0.05 20Hz 0.02 0.01 10m 0.02 0.01 10m 20m 50m 100m 200m 500m 1 2 3 Output Power [W] Output Power [W] Figure 33. THD+N vs. Output Power Figure 34. THD+N vs. Output Power 10 5 10 5 2 1 20kHz 2 1 20kHz THD [%] 0.5 THD [%] 1kHz 0.5 0.2 0.1 0.05 0.2 0.1 0.05 1kHz 20Hz 0.02 0.01 10m VDD=3.3V RL=4Ω Av=21.6dB 100m 200m 500m 1 2 3 0.02 0.01 10m 20Hz 20m 50m 100m 200m 500m 1 VDD=3.3V RL=8Ω Av=21.6dB 2 3 20m 50m Output Power [W] Output Power [W] Figure 35. THD+N vs. Output Power Figure 36. THD+N vs. Output Power 10 5 10 5 2 1 20kHz 2 1 20kHz THD [%] 0.5 THD [%] 1kHz 0.5 1kHz 0.2 0.1 0.2 0.1 0.05 20Hz 0.05 0.02 0.01 10m VDD=2.7V RL=4Ω Av=21.6dB 100m 200m 500m 1 2 3 20Hz 0.02 0.01 10m VDD=2.7V RL=8Ω Av=21.6dB 100m 200m 500m 1 2 3 20m 50m 20m 50m Output Power [W] Output Power [W] Figure 37. THD+N vs. Output Power Figure 38. THD+N vs. Output Power 12 FAN7033MP Performance Characteristics(Continued) 10 5 2 1 0.5 10 5 2 1 0.5 VDD=5V Output power =1W RL=4Ω VDD=5V Output power =1W RL=8Ω THD [%] 0.1 0.05 0.02 0.01 0.005 0.002 0.001 20 50 100 200 500 1k 2k 5k 10k 20k THD [%] 0.2 0.2 0.1 0.05 0.02 0.01 0.005 0.002 0.001 20 50 100 200 500 1k 2k 5k 10k 20k Frequency [Hz] Frequency [Hz] Figure 39. THD+N vs. Frequency Figure 40. THD+N vs. Frequency 10 5 2 1 0.5 10 VDD=3.3V Output power =500mW RL=4Ω 5 2 1 0.5 VDD=3.3V Output power =500mW RL=8Ω THD [%] 0.1 0.05 0.02 0.01 0.005 0.002 0.001 20 50 100 200 500 1k 2k 5k 10k 20k THD [%] 0.2 0.2 0.1 0.05 0.02 0.01 0.005 0.002 0.001 20 50 100 200 500 1k 2k 5k 10k 20k Frequency [Hz] Frequency [Hz] Figure 41. THD+N vs. Frequency Figure 42. THD+N vs. Frequency 10 5 2 1 0.5 10 VDD=2.7V Output power =250mW RL=4Ω 5 2 1 0.5 VDD=2.7V Output power =250mW RL=8Ω THD [%] 0.1 0.05 0.02 0.01 0.005 0.002 0.001 20 50 100 200 500 1k 2k 5k 10k 20k THD [%] 0.2 0.2 0.1 0.05 0.02 0.01 0.005 0.002 0.001 20 50 100 200 500 1k 2k 5k 10k 20k Frequency [Hz] Frequency [Hz] Figure 43. THD+N vs. Frequency Figure 44. THD+N vs. Frequency 13 FAN7033MP Performance Characteristics(continued) 4.0 3.5 Multi Layer Power Dissipation [W] 3.0 2.5 2.0 1.5 1.0 0.5 0.0 0 25 50 75 100 125 150 Single Layer Ambient Temperature [°C] Figure 45. Power Derating Curve Notes : - Single Layer(JESD51-3) : Thermal Vias : 0 Board Size : 76.2mm*114.3mm*1.57mm(JESD51-3) Copper Thickness : 2.0oz Copper Coverage : Top Layer : Traces + Metalization Area(3.34mm*2.24mm) - Multi Layer(JESD51-7) : Thermal Vias : 6 Board Size : 76.2mm*114.3mm*1.6mm(JESD51-7) Copper Thickness : 2.0oz/1.0oz/1.0oz Copper Coverage : Top Layer : Traces + Metalization Area(3.34mm*2.24mm) Middle Layers(Power/Ground Planes) : 74.2mm*74.2mm - JESD51-3 : Low Effective Thermal Conductivity Test Board for Leaded Surface Mount Packages(Single Layer) - JESD51-7 : High Effective Thermal Conductivity Test Board for Leaded Surface Mount Packages(Multi Layers) - JESD51-2 : Integrated Circuits Thermal Test Method Environmental Conditions - Natural Convection(Still Air) 14 FAN7033MP Applications Information Functional Description The FAN7033MP is a stereo power amplifier capable of delivering 1.9W continuous RMS(Root Mean Square) power into 4Ω load with 1% THD(Total Harmonic Distortion). At 10% THD, the FAN7033MP can deliver above 2W into 4Ω load. The FAN7033MP has 5 supply input pins. Three among them are used for positive supply and the rest of them is for the ground. Three positive supply input pins : pin3(PVDD2), pin10(PVDD1) and pin11(VDD) must be tied together. To improve the cross-talk between cannels, these pins are not connected internally. Therefore, these pins must be externally connected on the PCB. Pin 8 and the exposed pad are allocated to ground. Thus, the exposed pad must be connected to the ground. The FAN7033MP is provided with differential inputs. These inputs increase the common-mode noise immunity. Furthermore, differential configuration in the input section helps to decrease total harmonic distortion and pop noise that occurs when shutdown is released. When only single input is available, the distortion performance is slightly degraded. To save the standby power consumption, the FAN7033MP provides shutdown function. Putting pin14(SD) to be low, the chip falls into shutdown mode. At this mode, it consumes micro power at the room temperature of 25°C and this power consumption is only due to the leakage current of the chip. This leakage current is the strong function of the temperature. Thus at the high ambient temperature, the shutdown current slightly increases. The logic threshold of shutdown pin lies nearby VDD/2. So, the logic threshold level does not follow TTL logic level. Thus, when the users want to control the chip according to the TTL logic level, some kinds of logic-level-changing circuit may be needed. Operation of the Amplifier 90kΩ INN CINN 15kΩ OUTP AMP1 15kΩ INP CINP 15kΩ OUTN AMP2 15kΩ 90kΩ 90kΩ 90kΩ VDD/2 Figure 1. Configuration of Power Amplifier Figure 1 shows the configuration of the single channel BTL(Bridge-Tied Load) power amplifier. To make the differential input configuration, the FAN7033MP uses several resistor networks as depicted in figure 1. For the input resistor, 15kΩ is used. This resistor converts the input voltage signal to the current signal. The converted current signal flows to the feedback resistor. For FAN7033MP, the feedback resistance is six times larger than input resistance. Thus, the gain is 12(about 21.6dB). For the 5V supply, the input signal has 0.83Vpeak voltage swing makes 10Vpp output swing. The exact gain formula is given by OUTP – OUTN = 12 ( INP – INN ) (1) As shown in equation (1), for the single-ended input case, the gain is also preserved. However, to get the same output swing with the differential input case, the input swing must be double comparing with the differential input swing. PCB Layout and Supply Regulation Metal trace resistance between the BTL output and the parasitic resistance of the power supply line both heavily 15 FAN7033MP affect the output power. In order to obtain the maximum power depicted in the performance characteristics figures, outputs, power, and ground lines need wide metal trace. The parasitic resistance of the power line increases ripple noise and degrades the THD and PSRR performance. To reduce such unwanted effect, a large capacitor must be connected between VDD pin and GND pin as close as possible. To improve power supply regulation performance, use a capacitor with low ESR. Power Supply Bypassing Selection of a proper power supply bypassing capacitor is critical to obtaining lower noise as well as higher power supply rejection. Larger capacitors may help to increase immunity to the supply noise. However, considering economical design, attaching 10µF electrolytic capacitor or tantalum capacitor with 0.1µF ceramic capacitor as close as possible to the VDD pins are enough to get a good supply noise rejection. Selection of Input Capacitor The input capacitors CINN and CINP block the DC voltage also low frequency input signal. Thus, these capacitors act as a high pass filter. When there are DC level differences between input source and the amplifier, these capacitors block DC voltage and make easy connection. However, these capacitors limit the low frequency input signal. Thus to cover the full audio frequency range, the values of these are very important. The input impedance and the capacitance of these capacitors stand for the low frequency characteristics and -3dB frequency is 1 f L = ---------------------------2 π ⋅ Zin ⋅ C (2) Where Zin is the input equivalent impedance and C is the capacitance of the input capacitor. For FAN7033MP, the input has several resistors and these resistors determine the input impedance. In the normal condition, (-) input of the amplifier looks like a voltage source since the negative feedback topology makes (-) input virtually be the AC ground. Thus, resistance between the negative input of the amplifier and input pin is 15kΩ. The resistance toward (+) input is the summation of 15kΩ and 90kΩ. Thus total input impedance is Zin = 15k Ω || ( 15k Ω + 90k Ω ) = 13.125k Ω (3) Considering fL=20Hz(the lowest frequency of the audio freqeuncy range), it is possible to get the capacitance value from equation(2) and (3) as follow: 1 Cin = ---------------------------- = 0.606uF 2 π ⋅ Zin ⋅ f L (4) Thus, Cin must be higher than 0.606uF. In the application note, 1uF is chosen by considering input impedance variation during the chip fabrication. When using a capacitor which has the polarity, customers must carefully connect the capacitor. The input DC level of the FAN7033MP is a half of VDD. Thus, if the DC level of a source is higher than VDD/2, the positive lead of the capacitor must be faced toward the source. Shutdown Mode In order to reduce power consumption while not in use, the FAN7033MP contains a shutdown pin to externally turnoff bias circuitry. This shutdown feature turns the amplifier off when a logic low is placed on the shutdown pin. The trigger point between a logic low and logic high level is typically half-supply. It is best to switch between ground and supply to provide maximum device performance. By switching the shutdown pin to VDD , the FAN7033MP supply current draw will be minimized in idle mode. In either case, the shutdown pin should be tied to a definite voltages to avoid unwanted state changes. In many appplications, a microcontroller or microprocessor output is used to control the shutdown circuitry which provides a quick, smooth transition into shutdown. Another solution is to use a single-pole, single-throw switch in conjunction with an external pull-down resistor. When the switch is closed, the shutdown pin is connected to VDD and enables the amplifier. If the switch is open, then the external pull-down resistor will disable the FAN7033MP. This scheme guarantees that the shutdown pin will not float thus preventing unwanted state changes. 16 FAN7033MP Single-Ended Input For the case, a source does not provide the fully differential signal, the residual input must be well treated. 90kΩ INPUT CINN 15kΩ OUTP AMP1 15kΩ 15kΩ FLOATING 15kΩ 90kΩ 90kΩ OUTN AMP2 90kΩ VDD/2 Case (A) : Residual Input Pin Floating 90kΩ INPUT CINN 15kΩ OUTP AMP1 15kΩ CINP 15kΩ OUTN AMP2 15kΩ 90kΩ 90kΩ 90kΩ VDD/2 Case (B) : AC Coupling to Ground Case(A) : For this case, input is left alone without any treatment, that is, input pin is floating. Even the pin is floating, the BTL amplifier works and drives load. However, this configuration might cause unwanted noise at the output signal. Furthemore, floated configuration decreases PSRR(Power Supply Rejection Ratio) and increase POP noise. Case(B) : Case(B) is strongly recommended. This configuration increases PSRR and decreases POP noise as well. Of cource, to get the best performance, CINP must be the same value with CINN. THD+N(Total Harmonic Distortion plus Noise) THD+N stands for linearity and output noise of the amplifier as well. The FAN7033MP has the circuit for enhancing THD. In spite of that, to get low THD+N, users should follow the recommendation: (1) Use fully differential input configuration : A fully differential input makes low THD at output. Thus, for a singleended input case, THD+N slightly increaes. (2) Do not miss CBYP. CBYP helps to increase PSRR. Thus, using this capacitor, it is possible to increase noise immunity from the supply line. (3) Do not miss CSUP. Voltage fluctuation in supply line increases THD. Thus, such voltage fluctuation must be reduced to get low THD by connecting this capacitor between all VDD pins and the ground as closely as possible. 17 FAN7033MP Mechanical Dimensions Package Dimensions in millimeters 14MLP 18 FAN7033MP Ordering Information Device FAN7033MP Package 14MLP Operating Temperature -40°C ~ +85°C 19 FAN7033MP DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. www.fairchildsemi.com 8/20/03 0.0m 001 Stock#DSxxxxxxxx  2003 Fairchild Semiconductor Corporation 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness.