FAN7529 Critical Conduction Mode PFC Controller
April 2007
FAN7529
Critical Conduction Mode PFC Controller
Features
Low Total Harmonic Distortion (THD) Precise Adjustable Output Over-Voltage Protection Open-Feedback Protection and Disable Function Zero Current Detector 150µs Internal Start-up Timer MOSFET Over-Current Protection Under-Voltage Lockout with 3.5V Hysteresis Low Start-up (40µA) and Operating Current (1.5mA) Totem Pole Output with High State Clamp +500/-800mA Peak Gate Drive Current 8-Pin DIP or 8-Pin SOP
Description
The FAN7529 is an active power factor correction (PFC) controller for boost PFC applications that operates in critical conduction mode (CRM). It uses the voltage mode PWM that compares an internal ramp signal with the error amplifier output to generate MOSFET turn-off signal. Because the voltage-mode CRM PFC controller does not need rectified AC line voltage information, it saves the power loss of the input voltage sensing network necessary for the current-mode CRM PFC controller. FAN7529 provides many protection functions, such as over-voltage protection, open-feedback protection, overcurrent protection, and under-voltage lockout protection. The FAN7529 can be disabled if the INV pin voltage is lower than 0.45V and the operating current decreases to 65µA. Using a new variable on-time control method, THD is lower than the conventional CRM boost PFC ICs.
Applications
Adapter Ballast LCD TV, CRT TV SMPS
Related Application Notes
AN-6026 - Design of Power Factor Correction Circuit Using FAN7529
Ordering Information
Part Number
FAN7529N FAN7529M FAN7529MX
Operating Temp. Range
-40°C to +125°C -40°C to +125°C -40°C to +125°C
Pb-Free
Yes Yes Yes
Package
8-DIP 8-SOP 8-SOP
Packing Method
Rail Rail Tape & Reel
Marking Code
FAN7529 FAN7529 FAN7529
© 2006 Fairchild Semiconductor Corporation FAN7529 Rev. 1.0.2
www.fairchildsemi.com
FAN7529 Critical Conduction Mode PFC Controller
Typical Application Diagrams
L AC IN VAUX NAUX D VO
RZCD R2 ZCD CO VCC MOT CS COMP R1 GND
FAN7529 Rev. 00
FAN7529
INV
Figure 1. Typical Boost PFC Application
Internal Block Diagram
VCC 8 UVLO 2.5V Ref Internal Bias Vref1
VCC
12V
8.5V
Disable Timer
Drive Output
7 OUT
ZCD 5 6.7V 1.4V 1.5V Zero Current Detector
S Q R OVP 2.675V 2.5V
CS
4 40k 8pF 0.8V Current Protection Comparator
Disable
0.45V 0.35V
Ramp Signal Saw Tooth MOT 3 Generator 2.9V
1V Offset
Vref1 Error Amplifier
Gm
1V~5V Range 2 COMP
1 INV
6 GND
FAN7529 Rev. 00
Figure 2. Functional Block Diagram of FAN7529
© 2006 Fairchild Semiconductor Corporation FAN7529 Rev. 1.0.2 2
www.fairchildsemi.com
FAN7529 Critical Conduction Mode PFC Controller
Pin Assignments
VCC 8 OUT 7 GND 6 ZCD 5
YWW
FAN7529
1 INV 2 COMP 3 MOT 4 CS
FAN7529 Rev. 00
Figure 3. Pin Configuration (Top View)
Pin Definitions
Pin #
1 2
Name
INV COMP
Description
This pin is the inverting input of the error amplifier. The output voltage of the boost PFC converter should be resistively divided to 2.5V. This pin is the output of the transconductance error amplifier. Components for output voltage compensation should be connected between this pin and GND. This pin is used to set the slope of the internal ramp. The voltage of this pin is maintained at 2.9V. If a resistor is connected between this pin and GND, current flows out of the pin and the slope of the internal ramp is proportional to this current. This pin is the input of the over-current protection comparator. The MOSFET current is sensed using a sensing resistor and the resulting voltage is applied to this pin. An internal RC filter is included to filter switching noise. This pin is the input of the zero current detection block. If the voltage of this pin goes higher than 1.5V, then goes lower than 1.4V, the MOSFET is turned on. This pin is used for the ground potential of all the pins. For proper operation, the signal ground and the power ground should be separated. This pin is the gate drive output. The peak sourcing and sinking current levels are +500mA and -800mA respectively. For proper operation, the stray inductance in the gate driving path must be minimized. This pin is the IC supply pin. IC current and MOSFET drive current are supplied using this pin.
3
MOT
4
CS
5 6
ZCD GND
7
OUT
8
VCC
© 2006 Fairchild Semiconductor Corporation FAN7529 Rev. 1.0.2 3
www.fairchildsemi.com
FAN7529 Critical Conduction Mode PFC Controller
Absolute Maximum Ratings
Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. The absolute maximum ratings are stress ratings only. TA = 25°C unless otherwise specified.
Symbol
VCC IOH, IOL Iclamp Idet VIN TJ TA TSTG VESD_HBM VESD_MM VESD_CDM Supply Voltage
Parameter
Peak Drive Output Current Driver Output Clamping Diodes VO>VCC or VO90% at 85VAC input) Low Total Harmonic Distortion (THD) (
很抱歉,暂时无法提供与“FAN7529”相匹配的价格&库存,您可以联系我们找货
免费人工找货