FAN7621_10

FAN7621 — PFM Controller for Half-Bridge Resonant Converters July 2010 FAN7621 PFM Controller for Half-Bridge Resonant Converters Features Variable Frequency Control with 50% Duty Cycle for Half-bridge Resonant Converter Topology High Efficiency through Zero Voltage Switching (ZVS) Fixed Dead Time (350ns) Up to 300kHz Operating Frequency Pulse Skipping for Frequency Limit (Programmable) at Light-Load Condition Remote On/Off Control Using CON Pin Protection Functions: Over-Voltage Protection (OVP), Overload Protection (OLP), Over-Current Protection (OCP), Abnormal Over-Current Protection (AOCP), Internal Thermal Shutdown (TSD) Description The FAN7621 is a pulse frequency modulation controller for high-efficiency half-bridge resonant converters. Offering everything necessary to build a reliable and robust resonant converter, the FAN7621 simplifies designs and improves productivity, while improving performance. The FAN7621 includes a high-side gatedrive circuit, an accurate current controlled oscillator, frequency limit circuit, soft-start, and built-in protection functions. The high-side gate-drive circuit has a common-mode noise cancellation capability, which guarantees stable operation with excellent noise immunity. Using the zero-voltage-switching (ZVS) technique dramatically reduces the switching losses and efficiency is significantly improved. The ZVS also reduces the switching noise noticeably, which allows a small-sized Electromagnetic Interference (EMI) filter. The FAN7621 can be applied to various resonant converter topologies; such as series resonant, parallel resonant, and LLC resonant converters. Applications PDP and LCD TVs Desktop PCs and Servers Adapters Telecom Power Supplies Video Game Consoles Related Resources AN4151 — Half-bridge LLC Resonant Converter Design TM using FSFR-series Fairchild Power Switch (FPS ) Ordering Information Part Number FAN7621N FAN7621SJ FAN7621SJX -40°C ~ 130°C Operating Junction Temperature Package 16-Lead, Dual Inline Package (DIP) 16-Lead, Small-Outline Package (SOP) 16-Lead, Small-Outline Package (SOP) Packaging Method Tube Tube Tape & Reel © 2009 Fairchild Semiconductor Corporation FAN7621 • Rev. 1.0.3 www.fairchildsemi.com FAN7621 — PFM Controller for Half-Bridge Resonant Converters Application Circuit Diagram Cr L lk VCC LVcc HV CC D1 Np Ns VO Lm Ns CF R F FAN7621 RT HO CTR VIN CDL CON D2 KA431 LO CS SG PG Rsense Figure 1. Typical Application Circuit (LLC Resonant Half-Bridge Converter) Block Diagram LVCC 12 + VREF I CTC I CTC 3V LVCC good Internal Bias + - 2ICTC 2V 1V + F/F - Time Delay Level-Shift High-Side Gate Drive RT CON 8 350ns Counter (1/4) 2 LVCC I OLP 6 0.4 / 0.6 V + - Time Delay Balancing Delay Low-Side Gate Drive 350ns Shutdown without delay + + OLP 5V - S Q -Q Q -Q S R LVCC 23 V + LVCC good R -1 0.9 V - OVP Auto-restart Protection 50ns Delay - V AOCP TSD LVCC < 5V Delay 1.5µs - Latch Protection V OCP 0.58 V + 9 CS Figure 2. Internal Block Diagram © 2009 Fairchild Semiconductor Corporation FAN7621 • Rev. 1.0.3 2 + R -Q 1 S Q 11.3 / 14.5V - VREF HVCC good 8.7 / 9.2V HVCC HO CTR LO + - 3 14 16 PG SG 10 www.fairchildsemi.com FAN7621 — PFM Controller for Half-Bridge Resonant Converters Pin Configuration (1) HVCC (2) CTR (3) HO (4) NC (5) NC (6) CON (7) NC (8) RT Figure 3. Package Diagram PG (16) NC (15) LO (14) FAN7621 NC (13) LVCC (12) NC (11) SG (10) CS (9) Pin Definitions Pin # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Name HVCC CTR HO NC NC CON NC RT CS SG NC LVCC NC LO NC PG Description This is the supply voltage of the high-side gate-drive circuit IC. This is the drain of the low-side MOSFET. Typically, a transformer is connected to this pin. This is the high-side gate driving signal. No connection. No connection. This pin is for a protection and enabling/disabling the controller. When the voltage of this pin is above 0.6V, the IC operation is enabled. When the voltage of this pin drops below 0.4V, gate drive signals for both MOSFETs are disabled. When the voltage of this pin increases above 5V, protection is triggered. No connection. This pin programs the switching frequency. Typically, an opto-coupler is connected to control the switching frequency for the output voltage regulation. This pin senses the current flowing through the low-side MOSFET. Typically, negative voltage is applied on this pin. This pin is the control ground. No connection. This pin is the supply voltage of the control IC. No connection. This is the low-side gate driving signal. No connection. This pin is the power ground. This pin is connected to the source of the low-side MOSFET. www.fairchildsemi.com 3 © 2009 Fairchild Semiconductor Corporation FAN7621 • Rev. 1.0.3 FAN7621 — PFM Controller for Half-Bridge Resonant Converters Absolute Maximum Ratings Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. The absolute maximum ratings are stress ratings only. TA=25°C unless otherwise specified. Symbol VHO VLO LVCC VCTR VCON VCS VRT dVCTR/dt PD TJ TSTG Parameter High-Side Gate Driving Voltage Low-Side Gate Driving Voltage Low-Side Supply Voltage Center Voltage Control Pin Input Voltage Current Sense (CS) Pin Input Voltage RT Pin Input Voltage Allowable Center Voltage Slew Rate Total Power Dissipation 16-DIP 16-SOP (1) (1) Min. VCTR-0.3 -0.3 -0.3 -0.3 -0.3 -0.3 -5.0 -0.3 Max. HVCC LVCC 25.0 25.0 600.0 LVCC 1.0 5.0 50 1.56 1.13 +150 Unit V V V V V V V V/ns W W °C °C HVCC to VCTR High-Side VCC Pin to Center Voltage Maximum Junction Temperature Storage Temperature Range Recommended Operating Junction Temperature -40 -55 +130 +150 Note: 1. The maximum value of the recommended operating junction temperature is limited by thermal shutdown. Thermal Impedance Symbol θJA Parameter Junction-to-Ambient Thermal Impedance 16-DIP 16-SOP Value 80 110 Unit ºC/W © 2009 Fairchild Semiconductor Corporation FAN7621 • Rev. 1.0.3 www.fairchildsemi.com 4 FAN7621 — PFM Controller for Half-Bridge Resonant Converters Electrical Characteristics TA=25°C and LVCC=17V unless otherwise specified. Symbol Supply Section Parameter Offset Supply Leakage Current Quiescent HVCC Supply Current Quiescent LVCC Supply Current Operating HVCC Supply Current (RMS Value) Operating LVCC Supply Current (RMS Value) Test Conditions HVCC=VCTR (HVCCUV+) - 0.1V (LVCCUV+) - 0.1V fOSC=100kHz, VCON > 0.6V, CLoad=1nF No Switching, VCON < 0.4V fOSC=100kHz, VCON > 0.6V, CLoad=1nF No Switching, VCON < 0.4V Min. Typ. Max. 50 Unit μA μA μA mA μA mA mA ILK IQHVCC IQLVCC IOHVCC 50 100 5 100 6 2 120 200 8 200 9 4 IOLVCC UVLO Section LVCCUV+ LVCCUVLVCCUVH HVCCUV+ HVCCUVHVCCUVH LVCC Supply Under-Voltage Positive Going Threshold (LVCC Start) LVCC Supply Under-Voltage Negative Going Threshold (LVCC Stop) LVCC Supply Under-Voltage Hysteresis HVCC Supply Under-Voltage Positive Going Threshold (HVCC Start) HVCC Supply Under-Voltage Negative Going Threshold (HVCC Stop) HVCC Supply Under-Voltage Hysteresis 13.0 10.2 14.5 11.3 3.2 16.0 12.4 V V V 8.2 7.8 9.2 8.7 0.5 10.2 9.6 V V V Oscillator & Feedback Section VCONDIS VCONEN VRT fOSC DC fSS tSS Control Pin Disable Threshold Voltage Control Pin Enable Threshold Voltage V-I Converter Threshold Voltage Output Oscillation Frequency Output Duty Cycle Internal Soft-Start Initial Frequency Internal Soft-Start Time fSS=fOSC+40kHz, RT=5.2kΩ RT=5.2kΩ 0.36 0.54 1.5 94 48 0.40 0.60 2.0 100 50 140 0.44 0.66 2.5 106 52 V V V kHz % kHz 2 3 4 ms Output Section Isource Isink tr tf VHOH VHOL VLOH VLOL Peak Sourcing Current Peak Sinking Current Rising Time Falling Time High Level of High-Side Gate Driving Signal (VHVCC-VHO) Low Level of High-Side Gate Driving Signal High Level of High-Side Gate Driving Signal (VLVCC-VLO) Low Level of High-Side Gate Driving Signal HVCC=17V HVCC=17V CLoad=1nF, HVCC=17V 250 460 360 600 65 35 1.0 0.6 mA mA ns ns V V V V IO=20mA 1.0 0.6 © 2009 Fairchild Semiconductor Corporation FAN7621 • Rev. 1.0.3 www.fairchildsemi.com 5 FAN7621 — PFM Controller for Half-Bridge Resonant Converters Electrical Characteristics (Continued) TA=25°C and LVCC=17V unless otherwise specified. Symbol Protection Section Parameter OLP Delay Current OLP Protection Voltage LVCC Over-Voltage Protection AOCP Threshold Voltage AOCP Blanking Time OCP Threshold Voltage OCP Blanking Time (2) Test Conditions VCON=4V VCON > 3.5V LVCC > 21V Min. 3.8 4.5 21 -1.0 Typ. 5.0 5.0 23 -0.9 50 Max. 6.2 5.5 25 -0.8 Unit μA V V V ns IOLP VOLP VOVP VAOCP tBAO VOCP tBO tDA TSD ISU VPRSET -0.64 1.0 -0.58 1.5 250 -0.52 2.0 400 150 150 V μs ns °C Delay Time (Low-Side) Detecting from (2) VAOCP to Switch Off Thermal Shutdown Temperature (2) 110 LVCC=7.5V 5 130 100 Protection Latch Sustain LVCC Supply Current Protection Latch Reset LVCC Supply Voltage μA V Dead-Time Control Section DT Dead Time 350 ns Note: 2. These parameters, although guaranteed, are not tested in production. © 2009 Fairchild Semiconductor Corporation FAN7621 • Rev. 1.0.3 www.fairchildsemi.com 6 FAN7621 — PFM Controller for Half-Bridge Resonant Converters Typical Performance Characteristics These characteristic graphs are normalized at TA=25ºC. 1.1 1.1 1.05 1.05 Normalized at 25OC Normalized at 25OC 1 1 0.95 0.95 0.9 -50 -25 0 25 50 O 0.9 75 100 -50 -25 0 25 50 75 100 Temp ( C) Temp (OC) Figure 4. Low-Side MOSFET Duty Cycle vs. Temperature 1.1 Figure 5. Switching Frequency vs. Temperature 1.1 1.05 1.05 Normalized at 25OC 1 Normalized at 25OC -50 -25 0 25 50 75 100 1 0.95 0.95 0.9 0.9 -50 -25 0 25 50 75 100 Temp (OC) Temp (OC) Figure 6. High-Side VCC (HVCC) Start vs. Temperature 1.1 Figure 7. High-Side VCC (HVCC) Stop vs. Temperature 1.1 1.05 1.05 Normalized at 25OC 1 Normalized at 25OC -50 -25 0 25 50 75 100 1 0.95 0.95 0.9 0.9 -50 -25 0 25 50 75 100 Temp (OC) Temp (OC) Figure 8. Low-Side VCC (LVCC) Start vs. Temperature © 2009 Fairchild Semiconductor Corporation FAN7621 • Rev. 1.0.3 Figure 9. Low-Side VCC (LVCC) Stop vs. Temperature www.fairchildsemi.com 7 FAN7621 — PFM Controller for Half-Bridge Resonant Converters Typical Performance Characteristics (Continued) These characteristic graphs are normalized at TA=25ºC. 1.1 1.1 1.05 1.05 Normalized at 25OC Normalized at 25OC 1 1 0.95 0.95 0.9 -50 -25 0 25 50 75 100 0.9 -50 -25 0 25 50 75 100 Temp (OC) Temp (OC) Figure 10. OLP Delay Current vs. Temperature 1.1 Figure 11. OLP Protection Voltage vs. Temperature 1.1 1.05 1.05 Normalized at 25OC Normalized at 25OC 1 1 0.95 0.95 0.9 -50 -25 0 25 50 75 100 0.9 -50 -25 0 25 50 75 100 Temp (OC) Temp (OC) Figure 12. LVCC OVP Voltage vs. Temperature 1.1 Figure 13. RT Voltage vs. Temperature 1.1 1.05 1.05 Normalized at 25OC 1 Normalized at 25OC 1 0.95 0.95 0.9 -50 -25 0 25 50 75 100 0.9 -50 -25 0 25 50 75 100 Temp (OC) Temp (OC) Figure 14. CON Pin Enable Voltage vs. Temperature Figure 15. OCP Voltage vs. Temperature © 2009 Fairchild Semiconductor Corporation FAN7621 • Rev. 1.0.3 www.fairchildsemi.com 8 FAN7621 — PFM Controller for Half-Bridge Resonant Converters Functional Description 1. Basic Operation FAN7621 is designed to drive high-side and low-side MOSFETs complementarily with 50% duty cycle. A fixed dead time of 350ns is introduced between consecutive transitions, as shown in Figure 16. Dead t ime Gain 1.8 f min 1.6 f normal f max f ISS High-side MOSFET gate drive 1.4 1.2 Low-side MOSFET gate drve time 1.0 Soft-sta rt 0.8 Figure 16. MOSFETs Gate Drive Signal 0.6 60 70 80 90 100 110 120 130 140 150 2. Internal Oscillator FAN7621 employs a current-controlled oscillator, as shown in Figure 17. Internally, the voltage of RT pin is regulated at 2V and the charging / discharging current for the oscillator capacitor, CT, is obtained by copying the current flowing out of RT pin (ICTC) using a current mirror. Therefore, the switching frequency increases as ICTC increases. I CTC 3V Frequency (kHz) Figure 18. Resonant Converter Typical Gain Curve VCC LVCC HV CC VREF I CTC Rmax + Rmin RSS CON CSS FAN7621 SG RT HO CTR LO S - Q -Q 2I CTC 1V R + CT - F/F CS + RT 8 - 2V Counter (1/4) PG Gate drive R sense Figure 17. Current Controlled Oscillator Figure 19. Frequency Control Circuit The minimum switching frequency is determined as: 3. Frequency Setting Figure 18 shows the typical voltage gain curve of a resonant converter, where the gain is inversely proportional to the switching frequency in the ZVS region. The output voltage can be regulated by modulating the switching frequency. Figure 19 shows the typical circuit configuration for RT pin, where the optocoupler transistor is connected to the RT pin to modulate the switching frequency. f min = 5.2k Ω × 100(kHz ) Rmin (1) Assuming the saturation voltage of opto-coupler transistor is 0.2V, the maximum switching frequency is determined as: f max = ( 5.2k Ω 4.68k Ω + ) × 100(kHz ) Rmin Rmax (2) To prevent excessive inrush current and overshoot of output voltage during startup, increase the voltage gain of the resonant converter progressively. Since the voltage gain of the resonant converter is inversely proportional to the switching frequency, the soft-start is www.fairchildsemi.com 9 © 2009 Fairchild Semiconductor Corporation FAN7621 • Rev. 1.0.3 FAN7621 — PFM Controller for Half-Bridge Resonant Converters Rmax R min RSS CON CSS FAN7621 SG implemented by sweeping down the switching frequency ISS from an initial high frequency (f ) until the output voltage is established. The soft-start circuit is made by connecting R-C series network on the RT pin, as shown in Figure 19. FAN7621 also has an internal soft-start for 3ms to reduce the current overshoot during the initial cycles, which adds 40kHz to the initial frequency of the external soft-start circuit, as shown in Figure 20. The initial frequency of the soft-start is given as: VCC LV CC HV CC RT HO f ISS = ( 5.2k Ω 5.2k Ω ) × 100 + 40 (kHz ) + Rmin RSS (3) CTR It is typical to set the initial (soft-start) frequency of two ~ three times the resonant frequency (fO) of the resonant network. The soft-start time is three to four times the RC time constant. The RC time constant is as follows: LO CS PG TSS = RSS ⋅ CSS fs f ISS (4) Figure 22. Control Pin Configuration for Pulse Skipping 40kHz Control loop take over Remote On / Off: When an auxiliary power supply is used for standby, the main power stage using FAN7621 can be shut down by pulling down the control pin voltage, as shown in Figure 23. R1 and C1 are used to ensure soft-start when switching resumes. OP1 Main Output time Figure 20. Frequency Sweeping of Soft-Start R1 4. Control Pin The FAN7621 has a control pin for protection, cycle skipping, and remote on/off. Figure 21 shows the internal block diagram for control pin. LVCC FAN7621 C1 Main Off CON IOLP 6 0.4 / 0.6V + - RT Rmin Aux Output + Stop Switching S R Q -Q OLP 5V - CON LVCC 23V + - LVCC good Auto-restart protection OP1 OVP Figure 23. Remote On / Off Circuit Figure 21. Internal Block of Control Pin Protection: When the control pin voltage exceeds 5V, protection is triggered. Detailed applications are described in the protection section. Pulse Skipping: FAN7621 stops switching when the control pin voltage drops below 0.4V and resumes switching when the control pin voltage rises above 0.6V. To use pulse-skipping, the control pin should be connected to the opto-coupler collector pin. The frequency that causes pulse skipping is given as: SKIP 5. Protection Circuits The FAN7621 has several self-protective functions, such as Overload Protection (OLP), Over-Current Protection (OCP), Abnormal Over-Current Protection (AOCP), Over-Voltage Protection (OVP), and Thermal Shutdown (TSD). OLP, OCP, and OVP are auto-restart mode protections; while AOCP and TSD are latch-mode protections, as shown in Figure 24. 5.1 Auto-Restart Mode Protection: Once a fault condition is detected, switching is terminated and the MOSFETs remain off. When LVCC falls to the LVCC stop voltage of 11.3V, the protection is reset. FAN7621 www.fairchildsemi.com 10 = 5.2 k 4.16 k + R min R max x100(kHz) (5) © 2009 Fairchild Semiconductor Corporation FAN7621 • Rev. 1.0.3 FAN7621 — PFM Controller for Half-Bridge Resonant Converters resumes normal operation when LVCC reaches the start voltage of 14.5V. 5.2 Latch-Mode Protection: Once this protection is triggered, switching is terminated and the gate output signals remain off. The latch is reset only when LVCC is discharged below 5V. LV CC 12 + 5.4 Current Sensing Using Resonant Capacitor Voltage: For high-power applications, current sensing using a resistor may not be available due to the severe power dissipation in the resistor. In that case, indirect current sensing using the resonant capacitor voltage can be a good alternative because the amplitude of the p-p resonant capacitor voltage (Vcr ) is proportional to the p-p resonant current in the primary side (Ip ) as: LV CC good 11/ 14 V V RE F - Internal Bias VCr p − p = I p p− p 2π f sCr (6) OCP OLP OVP LV CC good CON 20k Shutdown Auto-restart protection S R Q -Q Latch protection Q -Q S R To minimize power dissipation, a capacitive voltage divider is generally used for capacitor voltage sensing, as shown in Figure 27. LVCC HV CC AOCP CDL TSD LV CC < 5V CON RT FAN7621 F/F F/F HO CTR Ip Figure 24. Protection Blocks 5.3 Current Sensing Using Resistor: FAN7621 senses drain current as a negative voltage, as shown in Figure 25 and Figure 26. Half-wave sensing allows low power dissipation in the sensing resistor, while full-wave sensing has less switching noise in the sensing signal. Ip HV CC LO CS SG PG Csense CB 100 Cr V sense LV CC FAN7621 RT HO CTR C DL V CS CON VCr I ds LO CS SG PG VCrp-p R sense V CS I ds Vsense Vsensepk CB = VCr p− p Csense+ C B Vsensepk = VCON 2 pk V sense VCON Figure 25. Half-Wave Sensing I ds tDelay =R dC d pk Vsense Figure 27. Current Sensing Using Resonant Capacitor Voltage LVCC HV CC V CS FAN7621 RT HO CTR C DL V CS CON 5.5 Over-Current Protection (OCP): When the sensing pin voltage drops below -0.6V, OCP is triggered and the MOSFETs remain off. This protection has a shutdown time delay of 1.5µs to prevent premature shutdown during startup. 5.6 Abnormal Over-Current Protection (AOCP): If the secondary rectifier diodes are shorted, large current with extremely high di/dt can flow through the MOSFET before OCP or OLP is triggered. AOCP is triggered without shutdown delay when the sensing pin voltage drops below -0.9V. This protection is latch mode and reset when LVCC is pulled down below 5V. www.fairchildsemi.com 11 LO CS SG PG I ds R sense Figure 26. Full-Wave Sensing © 2009 Fairchild Semiconductor Corporation FAN7621 • Rev. 1.0.3 FAN7621 — PFM Controller for Half-Bridge Resonant Converters 5.7 Overload Protection (OLP): Overload is defined as the load current exceeding its normal level due to an unexpected abnormal event. In this situation, the protection circuit should trigger to protect the power supply. However, even when the power supply is in the normal condition, the overload situation can occur during the load transition. To avoid premature triggering of protection, the overload protection circuit should be designed to trigger only after a specified time to determine whether it is a transient situation or a true overload situation. Figure 27 shows a typical overload protection circuit. By sensing the resonant capacitor voltage on the control pin, the overload protection can be implemented. Using RC time constant, shutdown delay can be also introduced. The voltage obtained on the control pin is given as: 6. PCB Layout Guideline VCON = CB VCr p − p 2(CB + Csense ) p-p (7) where VCr voltage. is the amplitude of the resonant capacitor Duty imbalance problems may occur due to the radiated noise from main transformer, the inequality of the secondary-side leakage inductances of main transformer, and so on. Among them, it is one of the dominant reasons that the control components in the vicinity of RT pin are enclosed by the primary current flow pattern on PCB layout. The direction of the magnetic field on the components caused by the primary current flow is changed when the high-and-low side MOSFET turns on by turns. The magnetic fields with opposite direction from each other induce a current through, into, or out of the RT pin, which makes the turn-on duration of each MOSFET different. It is strongly recommended to separate the control components in the vicinity of RT pin from the primary current flow pattern on PCB layout. Figure 28 shows an example for the duty-balanced case. The yellow and blue lines show the primary current flows when the lower-side and higher-side MOSFETs turns on, respectively. The primary current does not enclose any component of controller. It is helpful to reduce the duty imbalance to make the loop configured between CON pin and opto-coupler as small as possible, as shown in the red line in Figure 28. 5.8 Over-Voltage Protection (OVP): When the LVCC reaches 23V, OVP is triggered. This protection is used when auxiliary winding of the transformer to supply VCC to the controller is utilized. 5.9 Thermal Shutdown (TSD): If the temperature of the junction exceeds approximately 130°C, the thermal shutdown triggers. Figure 28. Example for Duty Balancing © 2009 Fairchild Semiconductor Corporation FAN7621 • Rev. 1.0.3 www.fairchildsemi.com 12 FAN7621 — PFM Controller for Half-Bridge Resonant Converters Typical Application Circuit (Half-Bridge LLC Resonant Converter) Application LCD TV Device FAN7621 Input Voltage Range 390VDC (340~400VDC) Rated Output Power 200W Output Voltage (Rated Current) 24V-8.3A Features High efficiency ( >94% at 400VDC input) Reduced EMI noise through zero-voltage-switching (ZVS) Enhanced system reliability with various protection functions Figure 29. Typical Application Circuit © 2009 Fairchild Semiconductor Corporation FAN7621 • Rev. 1.0.3 FAN7621 www.fairchildsemi.com 13 FAN7621 — PFM Controller for Half-Bridge Resonant Converters Typical Application Circuit (Continued) Usually, LLC resonant converters require large leakage inductance value. To obtain a large leakage inductance, sectional winding method is used. Core: EC35 (Ae=106 mm ) Bobbin: EC35 (Horizontal) Transformer Model Number: SNX-2468-1 EC35 Np 2 2 13 N s2 12 N 10 s1 6 9 Figure 30. Transformer Construction Pins (S → F) Np Ns1 Ns2 6→2 12 → 9 10 → 13 Wire 0.08φ×88 (Litz Wire) 0.08φ×234 (Litz Wire) 0.08φ×234 (Litz Wire) Turns 36 4 4 Note Bifilar Winding Bifilar Winding Pins Primary-Side Inductance (Lp) Primary-Side Effective Leakage (Lr) 2－ 6 2－ 6 Specifications 550μH ± 10% 110μH ± 10% Remark 100kHz, 1V Short one of the secondary windings For more detailed information regarding the transformer, visit http://www.santronics-usa.com/documents.html or contact sales@santronics-usa.com or +1-408-734-1878 (Sunnyvale, California USA). © 2009 Fairchild Semiconductor Corporation FAN7621 • Rev. 1.0.3 www.fairchildsemi.com 14 FAN7621 — PFM Controller for Half-Bridge Resonant Converters Physical Dimensions 16 19.68 18.66 A 9 6.60 6.09 1 8 (0.40) TOP VIEW 0.38 MIN 5.33 MAX 3.42 3.17 3.81 2.92 2.54 0.58 A 0.35 1.78 1.14 17.78 SIDE VIEW NOTES: UNLESS OTHERWISE SPECIFIED A THIS PACKAGE CONFORMS TO JEDEC MS-001 VARIATION BB B) ALL DIMENSIONS ARE IN MILLIMETERS. C) DIMENSIONS ARE EXCLUSIVE OF BURRS, MOLD FLASH, AND TIE BAR PROTRUSIONS D) CONFORMS TO ASME Y14.5M-1994 E) DRAWING FILE NAME: N16EREV1 Figure 31. 16-Lead Dual Inline Package (DIP) 8.13 7.62 0.35 0.20 8.69 15 0 Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild’s worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products. Always visit Fairchild Semiconductor’s online packaging area for the most recent package drawings: http://www.fairchildsemi.com/packaging/. © 2009 Fairchild Semiconductor Corporation FAN7621 • Rev. 1.0.3 www.fairchildsemi.com 15 FAN7621 — PFM Controller for Half-Bridge Resonant Converters Physical Dimensions Figure 32. 16-Lead Small Outline Package (SOP) Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild’s worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products. Always visit Fairchild Semiconductor’s online packaging area for the most recent package drawings: http://www.fairchildsemi.com/packaging/. © 2009 Fairchild Semiconductor Corporation FAN7621 • Rev. 1.0.3 www.fairchildsemi.com 16 FAN7621 — PFM Controller for Half-Bridge Resonant Converters © 2009 Fairchild Semiconductor Corporation FAN7621 • Rev. 1.0.3 www.fairchildsemi.com 17