FAN8200MTC

www.fairchildsemi.com FAN8200/FAN8200D/FAN8200MTC FAN8200MP Features • • • • • • • • 3.3V and 5V MPU interface Dual H-bridge drivers for bipolar stepping motor drives Built-in vertical-PNP power transistors Wide supply voltage range (VCC = 2.5V ~ 7.0V) Low saturation voltage (0.4V@ 0.4A) Built-in chip enable function for each bridge Built-in shoot-through current protection Built-in thermal shutdown(TSD) function Low Voltage/Low Saturation Stepping Motor Driver Description The FAN8200/FAN8200D/FAN8200MTC/FAN8200MP is a monolithic intergrated circuit designed for two-phase stepping motor drive systems. It has dual H-bridge drivers with vertical-PNP power transistors. Each of the bridges has an independant enable pin, therefore it can be used for other applications as well as stepping motor drive systems. 14-DIP-300 1 14-SOP-225 1 14-TSSOP 1 14-MLP Typical Application • • • • • General low voltage stepping motor driver Floppy disk driver Camera stepping motor driver PC camera or security equipment motion controller Two channel DC motor driver for a digital still camera (DSC) • MPU interfaced general power driver (buffer) Ordering Information Device FAN8200 FAN8200D FAN8200DTF FAN8200MTC FAN8200MTCX FAN8200MPX Package 14-DIP-300 14-SOP-225 14-SOP-225 14-TSSOP 14-TSSOP 14-MLP Operating Temp. -20 ~ +75°C -20 ~ +75°C -20 ~ +75°C -20 ~ +75°C -20 ~ +75°C -30 ~ +80°C Rev. 1.0.5 ©2004 Fairchild Semiconductor Corporation FAN8200/FAN8200D/FAN8200MTC FAN8200MP Pin Assignments PGND 14 CE2 13 OUT3 12 VS2 11 OUT4 10 IN2 9 PGND 8 FAN8200/FAN8200D/ 8200MTC/8200MP 1 VCC 2 CE1 3 OUT1 4 VS1 5 OUT2 6 IN1 7 SGND Pin Definitions Pin Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Pin Name VCC CE1 OUT1 VS1 OUT2 IN1 SGND PGND IN2 OUT4 VS2 OUT3 CE2 PGND I/O I O O I I O O I Chip enable 1 Output 1 Power supply 1 Output 2 Input 1 Signal ground Power ground Input 2 Output 4 Power supply 2 Output 3 Chip enable 2 Power ground Pin Function Description Logic part supply voltage 2 FAN8200/FAN8200D/FAN8200MTC FAN8200MP Internal Block Diagram 4 VS1 VCC 1 3 50K IN1 6 80K Control Part1 OUT1 50K CE1 2 80K SGND 7 TSD & BIAS 5 OUT2 8 PGND 11 VS2 12 50K IN2 9 80K Control Part2 OUT3 50K CE2 13 10 80K 14 PGND OUT4 3 FAN8200/FAN8200D/FAN8200MTC FAN8200MP Absolute Maximum Ratings (Ta = 25°C) Parameter Supply voltage Power supply voltage Output voltage Input voltage Peak output current per channel Continuous output current per channel Symbol VCC(MAX) VS(MAX) VOUT(MAX) VIN(MAX) IO(PEAK) IO Value 9.0 9.0 VS + VCF 7.0 1 0.65 (FAN8200) 0.4 (FAN8200D) 0.55 (FAN8200MTC) 0.35 (FAN8200MP) 1.0 (FAN8200) 0.6 (FAN8200D) 0.87 (FAN8200MTC) 0.8 (FAN8200MP) 150 -40 ~ 125 -20 ~ 75(FAN8200) -20 ~ 75(FAN8200D) -20 ~ 75(FAN8200MTC) -30 ~ 80(FAN8200MP) Unit V V V V A A Power dissipation Junction temperture Storage temperature Operating temperature PDnote TJ TSTG TA W °C °C °C Notes: 1. When mounted on 76.2mm × 114mm × 1.57mm PCB (glass epoxy material). 2. Power dissipation reduces 8.0mW/°C for FAN8200, 4.8mW/°C for FAN8200D, 6.9mW/°C for FAN8200MTC and 6.4mW/°C FAN8200MP for Ta ≥ 25°C. 3. Should not exceed PD and SOA(Safe Operating Area). Power Dissipation Curve FAN8200 Power Dissipation : PD[W] 1.0 0.5 SOA 0 0 25 50 75 100 125 150 175 Ambient temperature, Ta [°C] 1.0 FAN8200D Power Dissipation : PD[W] 0.6 SOA 0 0 25 50 75 100 125 150 175 Ambient temperature, Ta [°C] 4 FAN8200/FAN8200D/FAN8200MTC FAN8200MP Power Dissipation Curve (Continued) FAN8200MTC Power Dissipation : PD[W] 1.0 0.5 SOA 0 0 25 50 75 100 125 150 175 Ambient temperature, Ta [°C] FAN8200MP Power Dissipation : PD[W] 1.0 0.5 SOA 0 0 25 50 75 100 125 150 175 Ambient temperature, Ta [°C] Recommended Operating Conditions (Ta = 25°C) Parameter Logic circuit supply voltage Power supply voltage Symbol VCC VS Min. 2.5 2.5 Typ. Max 7.0 7.0 Unit V V 5 FAN8200/FAN8200D/FAN8200MTC FAN8200MP Function Descriptions CE1 Low High High X: don’t care Z: high-impedance IN1 X Low High OUT1 Z High Low OUT2 Z Low High CE2 Low High High IN2 X Low High OUT3 Z High Low OUT4 Z Low High CE1 CE2 IN1 IN2 +VS Phase-A OUT1-OUT2 -VS High-Impedance High-Impedance +VS Phase-B OUT3-OUT4 -VS 6 FAN8200/FAN8200D/FAN8200MTC FAN8200MP Electrical Characteristics (Ta=25°C, VCC=5V, VS1=3V, VS2=3V, unless otherwise specified) Parameter Supply current 1 Supply current 2 Saturation voltage 1 (upper + lower total) Saturation voltage 2 (upper + lower total) Input high level voltage Input low level voltage Input current Chip enable current Clamp diode leakge current Clamp diode voltage Symbol ICC1 ICC2 VSAT1 VSAT2 VINH VINL IIN ICE ILEAK VCF Conditions CE1, 2=0V CE1=3V, CE2=0V or CE1=0V, CE2=3V CE1=3V, IN1=3V or 0V, IOUT=0.2A CE1=3V, IN1=3V or 0V, IOUT=0.4A IN=3V, Each pin CE=3V, Each pin VCC=7V, VS=7V IOUT=0.4A Min. 1.8 -0.3 Typ. 0.1 12 0.2 0.4 100 100 Max. 10 18 0.3 0.6 VCC 0.7 200 200 30 1.7 Unit uA mA V V V V uA uA uA V Typical Performance Characteristics VSAT vs. IOUT Characteristics Graph 1.0 0.8 VSAT VSAT[V][V] 0.6 0.4 0.2 0 0 100 200 300 400 500 600 700 IO[A] IOUT[A] 7 FAN8200/FAN8200D/FAN8200MTC FAN8200MP Test Circuits SW1 VCC 0.1uF SW2 4 VCC VS1 1 3 OUT1 SW4 IN1 6 Control Part1 6Ω SW5 15Ω CE1 2 5 OUT2 SGND PGND 7 TSD & BIAS 8 SW3 VS2 11 12 IN2 9 Control Part2 CE2 13 10 OUT3 SW6 SW7 15Ω OUT4 6Ω PGND 14 8 FAN8200/FAN8200D/FAN8200MTC FAN8200MP Typical Application Circuit VCC 0.1uF 4 VCC 1 3 IN1 VS1 OUT1 6 Control Part1 OUT2 CE1 2 5 PGND 7 TSD & BIAS 11 8 Stepping Motor VS2 SGND OUT3 12 IN2 From 3.3V or 5V Microprocessor CE2 13 10 PGND 14 9 Control Part2 OUT4 9 FAN8200/FAN8200D/FAN8200MTC FAN8200MP Application Example - Full Step Bipolar Drive Circuit Schematics FAN8200/D/MTC Application Example - Large Current Buffer Circuit Schematics FAN8200/D/MTC 10 FAN8200/FAN8200D/FAN8200MTC FAN8200MP Application Example - 2-Ch. dc Motor Driver for a Digital Still Camera(DSC) Circuit Schematics FAN8200/D/MTC Shutter direction Shutter enable IN1=high Shutter dc motor M IN1=low Iris direction Iris enable IN2=high M Iris dc motor IN2=low 11 FAN8200/FAN8200D/FAN8200MTC FAN8200MP Mechanical Dimensions (Unit: mm) Package Dimensions 14-DIP-300 6.40 ±0.20 0.252 ±0.008 2.08 ) 0.082 #14 ( #1 19.80 MAX 0.780 19.40 ±0.20 0.764 ±0.008 #7 #8 7.62 0.300 3.25 ±0.20 0.128 ±0.008 0.20 MIN 0.008 5.08 MAX 0.200 3.30 ±0.30 0.130 ±0.012 0.25 –0.05 +0.10 0~15° 0.010 –0.002 +0.004 12 2.54 0.100 0.46 ±0.10 0.018 ±0.004 1.50 ±0.10 0.059 ±0.004 FAN8200/FAN8200D/FAN8200MTC FAN8200MP Mechanical Dimensions (Unit: mm) (Continued) Package Dimensions 14-SOP-225 MIN 1.55 ±0.10 0.061 ±0.004 0.05 0.002 0.47 ) 0.019 MAX0.10 MAX0.004 1.27 0.050 +0.004 0.016 -0.002 0.406 +0.10 -0.05 ( #1 #14 8.70 MAX 0.343 #7 6.00 ±0.30 0.236 ±0.012 #8 1.80 MAX 0.071 +0.004 0.008 -0.002 +0.10 -0.05 0.20 3.95 ±0.20 0.156 ±0.008 0.60 ±0.20 0.024 ±0.008 5.72 0.225 0~ 8° 8.56 ±0.20 0.337 ±0.008 13 FAN8200/FAN8200D/FAN8200MTC FAN8200MP Mechanical Dimensions (Unit: mm) (Continued) Package dimensions 14-TSSOP 14 FAN8200/FAN8200D/FAN8200MTC FAN8200MP Mechanical Dimensions (Unit: mm) (Continued) Package dimensions 14-MLP 15 FAN8200/FAN8200D/FAN8200MTC FAN8200MP DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. www.fairchildsemi.com 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. 9/13/04 0.0m 001 Stock#DSxxxxxxxx  2003 Fairchild Semiconductor Corporation