FSA266L8X

FSA266 • NC7WB66 Low Voltage Dual SPST Normally Open Analog Switch or 2-Bit Bus Switch May 2000 Revised December 2005 FSA266 • NC7WB66 Low Voltage Dual SPST Normally Open Analog Switch or 2-Bit Bus Switch General Description The FSA266 or NC7WB66 is an ultra high-speed (UHS) dual single-pole/single-throw (SPST) analog switch or 2-bit bus switch. The device is fabricated with advanced sub-micron CMOS technology to achieve high speed enable and disable times and low On Resistance over a broad VCC range. The device is specified to operate over the 1.65 to 5.5V VCC operating range. The device is organized as a dual switch with independent CMOS compatible switch enable (OE) controls. When OE is HIGH, the switch is ON and Port A is connected to Port B. When OE is LOW, the switch is OPEN and a high-impedance state exists between the two ports. The enable inputs tolerate voltages up to 5.5V independent of the VCC operating range. Features O Useful in both analog and digital applications O Space saving US8 surface mount package O MicroPak¥ Pb-Free leadless package O Typical 7: On Resistance @ 5V VCC O Broad VCC operating range: 1.65V to 5.5V O Rail-to-Rail signal handling O Power down high impedance control inputs O Control inputs are overvoltage tolerant O Control inputs are CMOS compatible O !300 MHz 3dB bandwidth Ordering Code: Order Number FSA266K8X FSA266L8X NC7WB66K8X NC7WB66L8X Product Package Code Number Top Mark MAB08A MAC08A MAB08A MAC08A WB66 P4 WB66 P4 Package Description Supplied As 8-Lead US8, JEDEC MO-187, Variation CA 3.1mm Wide 3K Units on Tape and Reel Pb-Free 8-Lead MicroPak, 1.6 mm Wide Pb-Free 8-Lead MicroPak, 1.6 mm Wide 5K Units on Tape and Reel 5K Units on Tape and Reel 8-Lead US8, JEDEC MO-187, Variation CA 3.1mm Wide 3K Units on Tape and Reel Pb-Free package per JEDEC J-STD-020B. MicroPak¥ is a trademark of Fairchild Semiconductor Corporation. © 2005 Fairchild Semiconductor Corporation DS500373 www.fairchildsemi.com FSA266 • NC7WB66 Logic Symbol Connection Diagrams Pin Assignments for US8 (Top View) Analog Symbol Pad Assignments for MicroPak (Top Through View) Pin Descriptions Pin Names A B OE Description Switch Port A Switch Port B Control Input Function Table Switch Enable Input (OE) L H H HIGH Logic Level L LOW Logic Level Function Disconnect B Connected to A www.fairchildsemi.com 2 FSA266 • NC7WB66 Absolute Maximum Ratings(Note 1) Supply Voltage (VCC) DC Switch Voltage (VS) DC Input Voltage (VIN) (Note 2) DC Input Diode Current @ (IIK) VIN  0V DC Switch Output Current (IOUT) DC VCC or Ground Current (ICC/IGND) Storage Temperature Range (TSTG) Junction Lead Temperature under Bias (TJ) Junction Lead Temperature (TL) Power Dissipation (PD) @ 85qC SC70-6 (Soldering, 10 Seconds) 0.5V to 7.0V 0.5V to VCC  0.5V 0.5V to 7.0V r128 mA r100 mA 65qC to 150qC 150qC 260qC 250 mW Recommended Operating Conditions (Note 3) Supply Voltage (VCC) Control Input Voltage (VIN) Switch Input Voltage (VIN) Switch Output Voltage (VOUT) Operating Temperature (TA) Input Rise and Fall Time (tr, tf) Control Input VCC Control Input VCC Control Input VCC 1.65V2.7V 3.0V3.6V 4.5V5.5V 1.65V to 5.5V 0V to 5.5V 0V to VCC 0V to VCC 50 mA 40qC to 85qC 0 ns/V to 20 ns/V 0 ns/V to 10 ns/V 0 ns/V to 5 ns/V 250qC/W Thermal Resistance (TJA) Note 1: The “Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be guaranteed. The device should not be operated at these limits. The parametric values defined in the Electrical Characteristics tables are not guaranteed at the absolute maximum ratings. The “Recommended Operating Conditions” table will define the conditions for actual device operation. Note 2: The input and output negative voltage ratings may be exceeded if the input and output diode current ratings are observed. Note 3: Unused inputs must be held HIGH or LOW. They may not float. DC Electrical Characteristics Symbol VIH VIL IIN IOFF RON Parameter HIGH Level Input Voltage LOW Level Input Voltage Input Leakage Current Switch OFF Leakage Current Switch On Resistance (Note 4) 4.5 VCC (V) 1.65 to 1.95 2.3 to 5.5 1.65 to 1.95 2.3 to 5.5 0 to 5.5 1.65 to 5.5 6.0 7.0 6.0 3.0 2.3 1.65 ICC Quiescent Supply Current All Channels ON or OFF Analog Signal Range RRange On Resistance Over Signal Range (Note 4)(Note 5) 7.5 8.5 9.0 10.5 12.5 17.0 5.5 VCC 4.5 3.0 2.3 1.65 4.5 3.0 2.3 1.65 Rflat On Resistance Flatness (Note 4)(Note 5)(Note 6) 4.5 3.0 2.3 1.65 0 8.0 15.0 45.0 150 0.2 0.2 0.5 0.6 2.5 8.0 33.0 135 6.0 17.5 60.0 250 6.0 17.5 60.0 250 Min 0.75 VCC 0.7 VCC 0.25 VCC 0.3 VCC TA 25qC Typ Max TA 40qC to 85qC Max Units Conditions Min 0.75 VCC 0.7 VCC V 0.25VCC 0.3 VCC V r0.1 r0.1 r1.0 r1.0 PA PA : : : : PA V 0 d VIN d 5.5V VI VI VI VI VI VI VI VI VI VIN IOUT IO 0V, IO 2.4V, IO 4.5V, IO 0V, IO 3V, IO 0V, IO 2.3V, IO 0V, IO 1.65V, IO 0 0 d A, B d VCC 30 mA 10.0 13.5 10.0 15.0 15.0 20.0 20.0 30.0 30.0 1.0 VCC 15.0 30.0 75.0 275 0 10.0 13.5 10.0 15.0 15.0 20.0 20.0 30.0 30.0 10.0 VCC 15.0 30.0 75.0 275 30 mA 30 mA 24 mA 24 mA 8 mA 8 mA 4 mA 4 mA VCC or GND : IO IO IO IO 'RON On Resistance Match Between Channels (Note 4)(Note 7) : IO IO IO IO IO IO IO 30 mA, 0 d VI d VCC 24 mA, 0 d VI d VCC 8 mA, 0 d VI d VCC 4 mA, 0 d VI d VCC 30 mA, VI 3.15 24 mA, VI 2.1 8 mA, VI 1.6 4 mA, VI 1.15 30 mA, 0 d VI d VCC 24 mA, 0 d VI d VCC 8 mA, 0 d VI d VCC 4 mA, 0 d VI d VCC Note 4: Measured by the voltage drop between A and B pins at the indicated current through the switch. On Resistance is determined by the lower of the voltages on the two (A or B) pins. Note 5: Guaranteed by design. Note 6: Flatness is defined as the difference between the minimum and maximum value of ON Resistance over the specified range of conditions. 3 www.fairchildsemi.com FSA266 • NC7WB66 Note 7: 'RON DC Electrical Characteristics (Continued) RON max  RON min measured at identical VCC, temperature and voltage levels. AC Electrical Characteristics Symbol tPHL, tPLH Parameter Propagation Delay Bus-to-Bus (Note 8) VCC (V) 4.5 to 5.5 3.0 to 3.6 2.3 to 2.7 1.65 to 1.95 tPZL, tPZH Output Enable Time Turn on Time 4.5 to 5.5 3.0 to 3.6 2.3 to 2.7 1.65 to 1.95 tPLZ, tPHZ Output Disable Time Turn Off Time 4.5 to 5.5 3.0 to 3.6 2.3 to 2.7 1.65 to 1.95 Q OIRR Xtalk BW THD Charge Injection (Note 9) Off Isolation (Note 10) Crosstalk 1.65 to 5.5 1.65 to 5.5 1.65 to 5.5 1.65 to 5.5 5 -55.0 0.8 1.2 1.5 2.5 0.8 1.5 2.0 3.0 Min TA 40qC to 85qC Typ 0.35 0.7 1.1 2.0 2.0 2.5 3.2 5.7 2.6 3.4 4.2 6.2 Max 1.0 1.5 2.5 4.0 3.2 3.9 5.6 10.0 4.1 5.0 6.9 10.5 Units Conditions Figure Number ns VI CL OPEN 50 pF, RU RD 500: Figures 1, 2 ns VI VI CL VI VI CL CL RL f RL f RL RL 0V for tPZH 2 x VCC for tPZL 50 pF, RU 0V for tPHZ 2 x VCC for tPLZ 50 pF, RU 0 :, f RD 1 MHz 5 pF, 5 pF, 0.1 nF, VGEN 50 :, CL 50 :, CL 10 MHz 50 : 500: RD 500: Figures 1, 2 ns Figures 1, 2 pC dB dB MHz % 0V, Figure 3 Figure 4 Figure 5 Figure 8 RGEN 10 MHz 70.0 !300 .016 3dB Bandwidth Total Harmonic Distortion (Note 9) 600: 600 Hz to 20 KHz 0.5 VP-P f Note 8: This parameter is guaranteed by design. The switch contributes no propagation delay other than the RC delay of the On Resistance of the switch and the 50 pF load capacitance. Note 9: Guaranteed by design. Note 10: Off Isolation 20 log10 [VA/VBn] Capacitance Symbol CIN CI/O (OFF) CI/O (ON) Parameter Control Pin Input Capacitance Switch Port Off Capacitance Switch Port Capacitance when Switch is Enabled Typ 2.5 5.0 10.0 Max Units pF pF pF VCC VCC VCC 0V 5.0V 5.0V Figure 6 Figure 7 Conditions Figures www.fairchildsemi.com 4 FSA266 • NC7WB66 AC Loading and Waveforms Input driven by 50: source terminated in 50: CL includes load and stray capacitance. Input PRR 1.0 MHz; tw 500 ns FIGURE 1. AC Test Circuit FIGURE 2. AC Waveforms FIGURE 3. Charge Injection Test 5 www.fairchildsemi.com FSA266 • NC7WB66 AC Loading and Waveforms (Continued) FIGURE 4. Off Isolation FIGURE 5. Crosstalk FIGURE 6. Channel Off Capacitance FIGURE 7. Channel On Capacitance FIGURE 8. Bandwidth www.fairchildsemi.com 6 FSA266 • NC7WB66 Tape and Reel Specification TAPE FORMAT for US8 Package Designator K8X Tape Section Leader (Start End) Carrier Trailer (Hub End) Number Cavities 125 (typ) 250 75 (typ) Cavity Status Empty Filled Empty Cover Tape Status Sealed Sealed Sealed TAPE DIMENSIONS inches (millimeters) TAPE FORMAT for MicroPak Package Designator L8X Tape Section Leader (Start End) Carrier Trailer (Hub End) Number Cavities 125 (typ) 250 75 (typ) Cavity Status Empty Filled Empty Cover Tape Status Sealed Sealed Sealed TAPE DIMENSIONS inches (millimeters) 7 www.fairchildsemi.com FSA266 • NC7WB66 REEL DIMENSIONS inches (millimeters) Tape Size 8 mm A 7.0 (177.8) B 0.059 (1.50) C 0.512 (13.00) D 0.795 (20.20) N 2.165 (55.00) 0.331  0.059/0.000 (8.40  1.50/0.00) W1 W2 0.567 (14.40) W1  0.078/0.039 (W1  2.00/1.00) W3 www.fairchildsemi.com 8 FSA266 • NC7WB66 Physical Dimensions inches (millimeters) unless otherwise noted 8-Lead US8, JEDEC MO-187, Variation CA 3.1mm Wide Package Number MAB08A 9 www.fairchildsemi.com FSA266 • NC7WB66 Physical Dimensions inches (millimeters) unless otherwise noted (Continued) Pb-Free 8-Lead MicroPak, 1.6 mm Wide Package Number MAC08A www.fairchildsemi.com 10 FSA266 • NC7WB66 Low Voltage Dual SPST Normally Open Analog Switch or 2-Bit Bus Switch DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION As used herein: provided in the labeling, can be reasonably expected to result in significant injury to the user. 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or 2. A critical component is any component of a life support (b) support or sustain life, or (c) whose failure to perform device or system whose failure to perform can be reasonwhen properly used in accordance with instructions for use ably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. PRODUCT STATUS DEFINITIONS Definition of terms Datasheet Identification Product Status Advance Information Preliminary Formative or In Design First Production Definition This datasheet contains the design specifications for product development. Specifications may change in any manner without notice. This datasheet contains preliminary data, and supplementary data will be published at a later date. Fairchild Semiconductor reserves the right to make changes at any time without notice in order to improve design. This datasheet contains final specifications. Fairchild Semiconductor reserves the right to make changes at any time without notice in order to improve design. This datasheet contains specifications on a product that has been discontinued by Fairchild Semiconductor. The datasheet is printed for reference information only. No Identification Needed Full Production Obsolete Not In Production 11 www.fairchildsemi.com