FSA5157P6X_NL

FSA5157 0.4: Low Voltage SPDT Analog Switch (Preliminary) November 2005 Revised November 2005 FSA5157 0.4: Low Voltage SPDT Analog Switch (Preliminary) General Description The FSA5157 is a low ON Resistance, low power Single Pole Double Throw (SPDT) analog switch. This product has been designed for switching audio signals in applications such as cell phones and portable media players. The ultra-low 0.4 Ohm impedance, sub 1P A current consumption, and 1.65V to 4.3V operating voltage range makes this product ideal for battery power applications. The FSA5157 also features bi-directional operation and make-before-break functionality. This device is fully specified for operation at 1.8V, 2.5V and 3.3V. A growing number of applications require the voltage applied to the select input to be lower then the VCC applied. Under this condition, most switches would typically consume over 100P A of current. This would be an unacceptable level for battery powered applications. The FSA5157 has been designed to minimize current consumption under this condition. The ICCT is specified for 12P A under a worse case condition of VCC = 4.3V and VIN = 1.8V. Features O Typical 0.4: On Resistance (RON) for 2.7V supply O FSA5157 features less than 12PA ICCT current when S input is lower than VCC O 0.25: maximum RON flatness for 2.7V supply O 1.0mm x 1.45mm 6-Lead Pb-Free MicroPak¥ package O Broad VCC operating range: 1.65V to 4.3V O Low THD (0.02% typical for 32: load) O High current handling capability (350mA continuous current under 3.3V supply) O Control logic is 1.8V CMOS logic compatible Applications O Cellular phone O PDA O Portable Media Player Ordering Code: Product Order Number FSA5157P6X FSA5157P6X_NL FSA5157L6X Package Number MAA06A MAA06A MAC06A Code Top Mark A57 A57 FT Package Description Supplied As 6-Lead SC70, EIAJ SC88, 1.25mm Wide 3K Units on Tape and Reel Pb-Free 6-Lead SC70, EIAJ SC88, 1.25mm Wide Pb-Free 6-Lead MicroPak, 1.0mm Wide 3K Units on Tape and Reel 5K Units on Tape and Reel Pb-Free package per JEDEC J-STD-020B. Applications Diagram MicroPak¥ is a trademark of Fairchild Semiconductor Corporation. © 2005 Fairchild Semiconductor Corporation DS500900 www.fairchildsemi.com FSA5157 Analog Symbols Pin Assignment for SC70 Truth Table Control Input(s) L H H = HIGH Logic Level L = LOW Logic Level Function B0 Connected to A B1 Connected to A Pin Descriptions Pin Names (Top View) Pin Assignment for MicroPak A, B0, B1 S Function Data Ports Control Input (Top Through View) www.fairchildsemi.com 2 FSA5157 Absolute Maximum Ratings(Note 1) Supply Voltage (VCC) Switch Voltage (VS) (Note 2) Input Voltage (VIN) (Note 2) Input Diode Current Switch Current Peak Switch Current (Pulsed at 1 ms duration, 10% Duty Cycle) Storage Temperature Range (TSTG) Maximum Junction Temperature (TJ) Lead Temperature (TL) Soldering, 10 seconds ESD Human Body Model 8000V 500 mA Recommended Operating Conditions Supply Voltage (VCC) Control Input Voltage (VIN) (Note 3) Switch Input Voltage (VIN) Operating Temperature (TA) 1.65V to 4.3V 0V to VCC 0V to VCC 0.5V to 4.6V 0.5V to VCC  3.0V 0.5V to 4.6V 50 mA 350 mA 40qC to 85qC 65qC to 150qC 150qC 260qC Note 1: The “Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be guaranteed. The device should not be operated at these limits. The parametric values defined in the Electrical Characteristics tables are not guaranteed at the absolute maximum ratings. The “Recommended Operating Conditions” table will define the conditions for actual device operation. Note 2: The input and output negative voltage ratings may be exceeded if the input and output diode current ratings are observed. Note 3: Unused inputs must be held HIGH or LOW. They may not float. DC Electrical Characteristics (All typical values are @ 25qC unless otherwise specified) Symbol VIH Parameter Input Voltage High VCC (V) 3.6 to 4.3 2.7 to 3.6 2.3 to 2.7 1.65 to 1.95 VIL Input Voltage Low 3.6 to 4.3 2.7 to 3.6 2.3 to 2.7 1.65 to 1.95 IIN INO(OFF), INC(OFF) IA(ON) Control Input Leakage OFF-Leakage Current of Port B0 and B1 ON Leakage Current of Port A RON Switch On Resistance (Note 4) 2.7 0.4 0.7 4.3 0.36 0.6 1.95 to 4.3 1.65 to 4.3 1.95 to 4.3 -10.0 10.0 Min TA = 25qC Typ Max TA = 40qC to 85qC Min 1.4 1.3 V 1.1 0.9 0.7 0.5 V 0.4 0.4 Max Units Conditions 0.5 50.0 100 0.5 50.0 PA nA VIN = 0V to VCC A = 0.3V, VCC  0.3V B0 or B1 = 0.3V, VCC  0.3V or Floating A = 0.3V, VCC  0.3V B0 or B1 = 0.3V, VCC  0.3V or Floating IOUT = 100 mA, B0 or 0.7V, 3.6V B0 or B1 = 0V, 0.7V, 3.6V, 4.3V IOUT = 100 mA, B0 or B1 = 0V, 20.0 20.0 100 nA : 2.3 0.55 0.8 0.7V, 2.0V, 2.7V IOUT = 100 mA, 0V or Delete 0.7V, 2.0V, 2.3V 1.65 1.5 0.04 0.06 0.12 1.0 2.5 3.0 0.75 0.13 0.2 IOUT = 100 mA, B0 or B1 = 0.7V 'RON On Resistance Matching Between Channels (Note 5) 4.3 2.7 2.3 1.65 : IOUT = 100 mA, B0 or B1 = 0.7V RFLAT(ON) On Resistance Flatness (Note 6) 4.3 2.7 2.3 1.65 0.3 0.25 0.25 0.3 : IOUT = 100 mA, B0 or B1 = 0V to VCC ICC ICCT Quiescent Supply Current Increase in ICC per Control Input 4.3 4.3 100.0 30.0 7.0 3.0 100.0 12.0 6.0 500 500 15.0 7.0 nA VIN = 0V or VCC, IOUT = 0V VIN = 1.8 VIN = 2.6 PA 3 www.fairchildsemi.com FSA5157 DC Electrical Characteristics (Continued) Note 4: On Resistance is determined by the voltage drop between A and B pins at the indicated current through the switch. Note 5: 'RON = RONmax  RONmin measured at identical VCC, temperature, and voltage. Note 6: Flatness is defined as the difference between the maximum and minimum value of On Resistance over the specified range of conditions. AC Electrical Characteristics (All typical value are @ 25qC unless otherwise specified) Symbol tON Parameter Turn ON Time VCC (V) 3.6 to 4.3 2.7 to 3.6 2.3 to 2.7 1.65 to 1.95 tOFF Turn OFF Time 3.6 to 4.3 2.7 to 3.6 2.3 to 2.7 1.65 to 1.95 tB-M Break-Before-Make Time 3.6 to 4.3 2.7 to 3.6 2.3 to 2.7 1.65 to 1.95 Q Charge Injection 3.6 to 4.3 2.7 to 3.6 2.3 to 2.7 1.65 to 1.95 OIRR OFF-Isolation 3.6 to 4.3 2.7 to 3.6 2.3 to 2.7 1.65 to 1.95 Xtalk Crosstalk 3.6 to 4.3 2.7 to 3.6 2.3 to 2.7 1.65 to 1.95 BW THD 6.0 6.0 pC 6.0 CL = 1.0 nF, VGEN = 0V, RGEN = 0: Figure 7 40.0 5.0 5.0 ns 5.0 5.0 B0 or B1 = 1.5V, RL = 50:, CL = 35 pF Figure 5 70.0 30.0 35.0 40.0 Min TA = 25qC Typ Max 55.0 60.0 65.0 TA= 40qC to 85qC Min Max 60.0 65.0 ns 70.0 90.0 35.0 40.0 ns 45.0 55.0 B0 or B1 = 1.5V, RL = 50:, CL = 35 pF Figure 4 B0 or B1 = 1.5V, RL = 50:, CL = 35 pF Figure 4 Figure Units Conditions Number 75.0 75.0 75.0 75.0 75.0 75.0 75.0 70.0 80.0 dB f = 100kHz, RL = 50:, CL = 5 pF (Stray) Figure 6 dB f = 100kHz, RL = 50:, CL = 5 pF (Stray) Figure 6 3db Bandwidth Total Harmonic Distortion 1.65 to 4.3 3.6 to 4.3 2.7 to 3.6 2.3 to 2.7 1.65 to 1.95 MHz RL = 5 0 : RL = 32:, VIN = 2V P.P, f= 20Hz to 20kHz RL = 32:, VIN = 1.5V P.P, f= 20Hz to 20kHz RL = 32:, VIN = 1.2V P.P, f= 20Hz to 20kHz Figure 9 0.02 % 0.036 0.01 Figure 10 Capacitance Symbol CIN COFF CON Parameter Control Pin Input Capacitance B Port OFF Capacitance A Port ON Capacitance VCC (V) 0.0 4.5 4.5 Min TA = 25qC Typ 1.5 21.0 90.0 Max TA = 40qC to 85qC Min Max pF pF pF f = 1MHz (see Figure 8) f = 1MHz (see Figure 8) f = 1MHz (see Figure 8) Units Conditions www.fairchildsemi.com 4 FSA5157 FIGURE 1. RON Switch On Resistance, ION = 100mA, VCC = 2.3V FIGURE 2. RON Switch On Resistance, ION = 100mA, VCC = 2.7V FIGURE 3. RON Switch On Resistance, ION = 100mA, VCC = 4.3V 5 www.fairchildsemi.com FSA5157 AC Loading and Waveforms CL includes Fixture and Stray Capacitance Logic Input Waveforms Inverted for Switches that have the Opposite Logic Sense FIGURE 4. Turn-On/Turn-Off Timing CL Includes Fixture and Stray Capacitance FIGURE 5. Break-Before-Make Timing FIGURE 6. OFF Isolation and Crosstalk www.fairchildsemi.com 6 FSA5157 AC Loading and Waveforms (Continued) Q = ('VOUT)(CL) FIGURE 7. Charge Injection FIGURE 8. ON/OFF Capacitance Measurement Setup FIGURE 9. Bandwidth FIGURE 10. Harmonic Distortion 7 www.fairchildsemi.com FSA5157 Tape and Reel Specification Tape Format For Micropak 6 Package Designator L6X Tape Section Leader (Start End) Carrier Trailer (Hub End) Number Cavities 125 (typ) 5000 75 (typ) Cavity Status Empty Filled Empty Cover Tape Status Sealed Sealed Sealed REEL DIMENSIONS inches (millimeters) Tape Size 8 mm A 7.0 (177.8) B 0.059 (1.50) C 0.512 (13.00) D 0.795 (20.20) N 2.165 (55.00) W1 0.331  0.059/0.000 (8.40  1.50/0.00) W2 0.567 (14.40) W3 W1  0.078/0.039 (W1  2.00/1.00) www.fairchildsemi.com 8 FSA5157 Physical Dimensions inches (millimeters) unless otherwise noted 6-Lead SC70, EIAJ SC88, 1.25mm Wide Package Number MAA06A 9 www.fairchildsemi.com FSA5157 Physical Dimensions inches (millimeters) unless otherwise noted (Continued) Pb-Free 6-Lead MicroPak, 1.0mm Wide Package Number MAC06A www.fairchildsemi.com 10 FSA5157 0.4: Low Voltage SPDT Analog Switch (Preliminary) DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION As used herein: provided in the labeling, can be reasonably expected to result in significant injury to the user. 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or 2. A critical component is any component of a life support (b) support or sustain life, or (c) whose failure to perform device or system whose failure to perform can be reasonwhen properly used in accordance with instructions for use ably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. PRODUCT STATUS DEFINITIONS Definition of terms Datasheet Identification Product Status Advance Information Preliminary Formative or In Design First Production Definition This datasheet contains the design specifications for product development. Specifications may change in any manner without notice. This datasheet contains preliminary data, and supplementary data will be published at a later date. Fairchild Semiconductor reserves the right to make changes at any time without notice in order to improve design. This datasheet contains final specifications. Fairchild Semiconductor reserves the right to make changes at any time without notice in order to improve design. This datasheet contains specifications on a product that has been discontinued by Fairchild Semiconductor. The datasheet is printed for reference information only. No Identification Needed Full Production Obsolete Not In Production 11 www.fairchildsemi.com