KSP2907A

KSP2907A PNP General Purpose Amplifier September 2006 KSP2907A PNP General Purpose Amplifier Features • Collector-Emitter Voltage: VCEO= 60V • Collector Power Dissipation: PC (max)=625mW • Suffix “-C” means a Center Collector (1.Emitter 2.Collector 3.Base) • Non suffix “-C” means a Side Collector (1.Emitter 2.Base 3.Collector) • Available as PN2907A KSP2907A 1 23 tm TO-92 : 1. Emitter 2. Base 3. Collector KSP2907AC : 1. Emitter 2. Collector 3. Base Absolute Maximum Ratings * T Symbol VCBO VCEO VEBO IC TJ Tstg Collector-Base Voltage Collector-Emitter Voltage Emitter-Base Voltage Collector current Junction Temperature Storage Temperature a = 25°C unless otherwise noted Parameter Value -60 -60 -5 -600 +150 -55 ~ +150 Units V V V mA °C °C * 1. These ratings are limiting values above which the serviceability of any semiconductor device may be impaired. 2. These are steady state limits. The factory should be consulted on applications involving pulsed or low duty cycle operations. Thermal Characteristics T =25°C unless otherwise noted a Symbol PC RθJC RθJA Parameter Collector Power Dissipation, by RθJA Thermal Resistance, Junction to Case(note1) Thermal Resistance, Junction to Ambient(note2) Max 625 83.3 200 Units mW °C/W °C/W Note1. Infinite heat sink. Note2. Minimum Land pad size. Electrical Characteristics * T Symbol V(BR)CBO V(BR)CEO V(BR)EBO ICBO hFE a = 25°C unless otherwise noted Parameter Collector-Base Breakdown Voltage Collector-Emitter Breakdown Voltage Emitter-Base Breakdown Voltage Collector Cutoff Current DC Current Gain Test Condition IC = -10µA, IE = 0 IC = -10mA, IB = 0 IE = -10µA, IC = 0 VCB = -50V, IE = 0 VCE = -10V, IC = -0.1mA, VCE = -10V, IC = -1mA, VCE = -10V, IC = -10mA, VCE = -10V, IC = -150mA, VCE = -10V, IC = -500mA, IC = -150mA, IB = -15mA IC = -500mA, IB = -50mA IC = -150mA, IB = -15mA IC = -500mA, IB = -50mA VCB = -10V, IE = 0, f = 1.0MHz IC = -50mA, VCE = -20V, f = 100MHz VCC= -30V, IC = -150mA, IB1= -15mA VCC= -6V, IC = -150mA,IB1= IB1 = -15mA Min. -60 -60 -5.0 Typ. Max. Units V V V nA -10 75 100 100 100 50 300 -0.4 -1.6 -1.3 -2.6 8 V V V V pF MHz ns ns VCE(sat) VBE(sat) Cobo fT tON tOFF Collector-Emitter Saturation Voltage Base-Emitter Saturation Voltage Output Capacitance Current Gain Bandwidth Product Turn On Time Turn Off Time 200 45 100 * DC Item are tested by Pulse Test: Pulse Width≤300us, Duty Cycle≤2% ©2006 Fairchild Semiconductor Corporation 1 www.fairchildsemi.com KSP2907A Rev. E KSP2907A PNP General Purpose Amplifier Package Marking and Ordering Information Device(note) KSP2907ABU KSP2907ACBU KSP2907ATA KSP2907ACTA KSP2907ATF Device Marking KSP2907A KSP2907AC KSP2907A KSP2907AC KSP2907A Package TO-92 TO-92 TO-92 TO-92 TO-92 Packing Method BULK BULK TAPE & AMMO TAPE & AMMO TAPE & REEL Qty(pcs) --2,000 2,000 2,000 Pin Definitions 1.Emitter 2.Base 3.Collector 1.Emitter 2.Collector 3.Base 1.Emitter 2.Base 3.Collector 1.Emitter 2.Collector 3.Base 1.Emitter 2.Base 3.Collector Note : Affix “-C-” - center collector pin. Suffix “-BU” - Bulk packing, straight lead form.(see package dimensions) Suffix “-TF” - Tape& Reel packing, 0.200 In-Line Spacing lead form. (see package dimensions) SUffix “-TA” - Tape& AMMO packing, 0.200 In-Line Spacing lead form. (see package dimensions) 2 KSP2907A Rev. E www.fairchildsemi.com KSP2907A PNP General Purpose Amplifier Typical Characteristics VBE(sat), VCE(sat)[V], SATURATION VOLTAGE -10 1000 VCE = -10V IC = 10 IB hFE, DC CURRENT GAIN -1 VBE(sat) 100 -0.1 VCE(sat) -0.01 -1 -10 -100 -1000 10 -1 -10 -100 -1000 IC[A], COLLECTOR CURRENT IC[mA], COLLECTOR CURRENT Figure 1. DC current Gain Figure 2. Collector-Emitter Saturation Voltage Base-Emitter Saturation Voltage 100 1000 IE = 0 f = 1MHz fT[MHz], CURRENT GAIN BANDWIDTH PRODUCT VCE = -20V Cob [pF], CAPACITANCE 10 100 1 0.1 -1 -10 -100 10 -1 -10 -100 -1000 VCB [V], COLLECTOR-BASE VOLTAGE IC[mA], COLLECTOR CURRENT Figure 3. Output Capacitance Figure 4. Current Gain Bandwidth Product 3 KSP2907A Rev. E www.fairchildsemi.com KSP2907A PNP General Purpose Amplifier Package Dimensions TO-92 Straight Lead Form 4.58 –0.15 +0.25 14.47 ±0.40 0.46 ±0.10 4.58 ±0.20 1.27TYP [1.27 ±0.20] 3.60 ±0.20 3.86MAX 1.27TYP [1.27 ±0.20] 0.38 –0.05 +0.10 1.02 ±0.10 0.38 –0.05 +0.10 (R2.29) (0.25) Dimensions in Millimeters Dimensions in Millime TO-92 0.200 In-Line Spacing Lead Form Dimensions in Inches[Millimeters] 4 KSP2907A Rev. E www.fairchildsemi.com KSP2907A PNP General Purpose Amplifier KSP2907A PNP General Purpose Amplifier TRADEMARKS The following are registered and unregistered trademarks Fairchild Semiconductor owns or is authorized to use and is not intended to be an exhaustive list of all such trademarks. ACEx™ ActiveArray™ Bottomless™ Build it Now™ CoolFET™ CROSSVOLT™ DOME™ EcoSPARK™ E2CMOS™ EnSigna™ FACT™ FAST® FASTr™ FPS™ FRFET™ FACT Quiet Series™ GlobalOptoisolator™ GTO™ HiSeC™ I2C™ i-Lo™ ImpliedDisconnect™ IntelliMAX™ ISOPLANAR™ LittleFET™ MICROCOUPLER™ MicroFET™ MicroPak™ MICROWIRE™ MSX™ MSXPro™ Across the board. Around the world.™ The Power Franchise® Programmable Active Droop™ OCX™ OCXPro™ OPTOLOGIC® OPTOPLANAR™ PACMAN™ POP™ Power247™ PowerEdge™ PowerSaver™ PowerTrench® QFET® QS™ QT Optoelectronics™ Quiet Series™ RapidConfigure™ RapidConnect™ µSerDes™ ScalarPump™ SILENT SWITCHER® SMART START™ SPM™ Stealth™ SuperFET™ SuperSOT™-3 SuperSOT™-6 SuperSOT™-8 SyncFET™ TCM™ TinyBoost™ TinyBuck™ TinyPWM™ TinyPower™ TinyLogic® TINYOPTO™ TruTranslation™ UHC™ UltraFET® UniFET™ VCX™ Wire™ DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN;NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. THESE SPECIFICATIONS DO NOT EXPAND THE TERMS OF FAIRCHILD’S WORLDWIDE TERMS AND CONDITIONS, SPECIFICALLY THE WARRANTY THEREIN, WHICH COVERS THESE PRODUCTS. LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, or (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. PRODUCT STATUS DEFINITIONS Definition of Terms Datasheet Identification Advance Information Product Status Formative or In Design Definition This datasheet contains the design specifications for product development. Specifications may change in any manner without notice. This datasheet contains preliminary data, and supplementary data will be published at a later date. Fairchild Semiconductor reserves the right to make changes at any time without notice in order to improve design. This datasheet contains final specifications. Fairchild Semiconductor reserves the right to make changes at any time without notice in order to improve design. Preliminary First Production No Identification Needed Full Production Obsolete Not In Production This datasheet contains specifications on a product that has been discontinued by Fairchild semiconductor. The datasheet is printed for reference information only. Rev. I20 5 KSP2907A Rev. E www.fairchildsemi.com