MM88C30M

MM88C29 • MM88C30 Quad Single-Ended Line Driver • Dual Differential Line Driver October 1987 Revised June 2001 MM88C29 • MM88C30 Quad Single-Ended Line Driver • Dual Differential Line Driver General Description The MM88C30 is a dual differential line driver that also performs the dual four-input NAND or dual four-input AND function. The absence of a clamp diode to VCC in the input protection circuitry of the MM88C30 allows a CMOS user to interface systems operating at different voltage levels. Thus, a CMOS digital signal source can operate at a VCC voltage greater than the VCC voltage of the MM88C30 line driver. The differential output of the MM88C30 eliminates ground-loop errors. The MM88C29 is a non-inverting single-wire transmission line driver. Since the output ON resistance is a low 20Ω typ., the device can be used to drive lamps, relays, solenoids, and clock lines, besides driving data lines. Features s Wide supply voltage range: 3V to 15V s High noise immunity: 0.45 VCC (typ.) s Low output ON resistance: 20Ω (typ.) Ordering Code: Order Number MM88C29N MM88C30M MM88C30N Package Number N14A M14A N14A Package Description 14-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300" Wide 14-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-012, 0.150" Narrow 14-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300" Wide Devices also available in Tape and Reel. Specify by appending suffix letter “X” to the ordering code. Connection Diagrams Pin Assignments for DIP MM88C29 Pin Assignments for DIP and SOIC MM88C30 Top View Top View © 2001 Fairchild Semiconductor Corporation DS005908 www.fairchildsemi.com MM88C29 • MM88C30 Logic Diagrams 1/4 MM88C29 1/2 MM88C30 www.fairchildsemi.com 2 MM88C29 • MM88C30 Absolute Maximum Ratings(Note 1) Voltage at Any Pin (Note 2) Operating Temperature Range Storage Temperature Power Dissipation (PD) Dual-In-Line Small Outline Operating VCC Range Absolute Maximum VCC 700 mW 500 mW 3V to 15V 18V Average Current at Output MM88C30 MM88C29 Maximum Junction Temperature, Tj Lead Temperature (Soldering, 10 seconds) 260°C 50 mA 25 mA 150°C −0.3V to VCC +16V −40°C to +85°C −65°C to +150°C Note 1: “Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be guaranteed. Except for “Operating Temperature Range” they are not meant to imply that the devices should be operated at these limits. The Electrical Characteristics tables provide conditions for actual device operation. Note 2: AC Parameters are guaranteed by DC correlated testing. DC Electrical Characteristics Min/Max limits apply across temperature range unless otherwise noted Symbol Parameter Conditions CMOS TO CMOS VIN(1) VIN(0) IIN(1) IIN(0) ICC ISOURCE Logical “1” Input Voltage Logical “0” Input Voltage Logical “1” Input Current Logical “0” Input Current Supply Current Output Source Current VCC = 5V VCC = 10V VCC = 5V VCC = 10V VCC = 15V, VIN = 15V VCC = 15V, VIN = 0V VCC = 5V VOUT = VCC − 1.6V, VCC ≥ 4.75V, Tj = 25°C Tj = 85°C MM88C29 MM88C30 ISINK Output Sink Current VOUT = VCC − 0.8V VCC ≥ 4.5V VOUT = 0.4V, VCC = 4.75V, Tj = 25°C Tj = 85°C VOUT = 0.4V, VCC = 10V, Tj = 25°C Tj = 125°C ISOURCE Output Source Resistance VOUT = VCC − 1.6V, VCC ≥ 4.75V, Tj = 25°C Tj = 85°C ISINK Output Sink Resistance VOUT = 0.4V, VCC = 4.75V, Tj = 25°C Tj = 85°C VOUT = 0.4V, VCC = 10V, Tj = 25°C Tj = 85°C Output Resistance Temperature Coefficient Source Sink θJA Thermal Resistance (N-Package) 0.55 0.40 150 %/°C %/°C °C/W 10 12 21 26 Ω Ω 18 22 41 50 Ω Ω 20 27 34 50 Ω Ω 19 15.5 40 33 mA mA 9.5 8 22 18 mA mA −47 −32 −2 −80 −60 −20 mA mA mA −1 0.005 −0.005 0.05 100 3.5 8 1.5 2 1 V V V V µA µA mA Min Typ Max Units OUTPUT DRIVE 3 www.fairchildsemi.com MM88C29 • MM88C30 AC Electrical Characteristics TA = 25°C, CL = 50 pF Symbol tpd Parameter Propagation Delay Time to Logical “1” or “0” MM88C29 MM88C30 tpd Differential Propagation Delay Time to Logical “1” or “0” MM88C30 CIN Input Capacitance MM88C29 MM88C30 CPD Power Dissipation Capacitance MM88C29 MM88C30 Note 3: Capacitance is guaranteed by periodic testing. (Note 2) Conditions Min Typ Max Units (See Figure 1) VCC = 5V VCC = 10V VCC = 5V VCC = 10V RL = 100Ω, CL = 5000 pF (See Figure 2) VCC = 5V VCC = 10V (Note 3) (Note 3) (Note 3) (Note 3) 5.0 5.0 150 200 400 150 ns ns pF pF pF pF 80 35 110 50 200 100 350 150 ns ns ns ns Note 4: CPD determines the no load AC power consumption of any CMOS device. For complete explanation see Family Characteristics application note AN-90 (CMOS Logic Databook). AC Test Circuits FIGURE 1. FIGURE 2. www.fairchildsemi.com 4 MM88C29 • MM88C30 Typical Applications Digital Data Transmission Note A: Exact value depends on line length. Note B: Optional to control response time. Note C: VCC= 4.5V to 5.5V for the DS7820, VCC=4.5V to 15V for the DS78C20. VCC is 3V to 15V. Typical Data Rate vs Transmission Line Length Note: The transmission line used was #22 gauge unshielded twisted pair (40k termination). Note: The curves generated assume that both drivers are driving equal lines, and that the maximum power is 500 mW/package. 5 www.fairchildsemi.com MM88C29 • MM88C30 Typical Performance Characteristics MM88C29 Typical Propagation Delay vs. Load Capacitance MM88C30 Typical Propagation Delay vs. Load Capacitance MM88C29 Typical Propagation Delay vs. Load Capacitance Typical Sink Current vs. Output Voltage MM88C30 Typical Propagation Delay vs. Load Capacitance Typical Source Current vs. Output Voltage www.fairchildsemi.com 6 MM88C29 • MM88C30 Physical Dimensions inches (millimeters) unless otherwise noted 14-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-012, 0.150" Narrow Package Number M14A 7 www.fairchildsemi.com MM88C29 • MM88C30 Quad Single-Ended Line Driver • Dual Differential Line Driver Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 14-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300" Wide Package Number N14A Fairchild does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and Fairchild reserves the right at any time without notice to change said circuitry and specifications. LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. www.fairchildsemi.com 8 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. www.fairchildsemi.com