NC7S08M5X-NL

NC7S08 TinyLogic£ HS 2-Input AND Gate October 1995 Revised January 2005 NC7S08 TinyLogic£ HS 2-Input AND Gate General Description The NC7S08 is a single 2-Input high performance CMOS AND Gate. Advanced Silicon Gate CMOS fabrication assures high speed and low power circuit operation over a broad VCC range. ESD protection diodes inherently guard both inputs and output with respect to the VCC and GND rails. Three stages of gain between inputs and outputs assures high noise immunity and reduced sensitivity to input edge rate. Features ■ Space saving SOT23 or SC70 5-lead package ■ High Speed; tPD 3.5 ns typ ■ Ultra small MicroPak¥ Pb-Free leadless package ■ Low Quiescent Power; ICC  1 PA ■ Balanced Output Drive; 2 mA IOL, 2 mA IOH ■ Broad VCC Operating Range; 2V–6V ■ Balanced Propagation Delays ■ Specified for 3V operation Ordering Code: Order Number NC7S08M5X NC7S08M5X_NL (Note 1) NC7S08P5X Package Product Code Number MA05B MA05B MAA05A Top Mark 7S08 7S08 S08 S08 PP Package Description 5-Lead SOT23, JEDEC MO-178, 1.6mm Pb-Free 5-Lead SOT23, JEDEC MO-178, 1.6mm 5-Lead SC70, EIAJ SC-88a, 1.25mm Wide Supplied As 3k Units on Tape and Reel 3k Units on Tape and Reel 3k Units on Tape and Reel NC7S08P5X_NL MAA05A (Note 1) NC7S08L6X MAC06A Pb-Free 5-Lead SC70, EIAJ SC-88a, 1.25mm Wide 3k Units on Tape and Reel Pb-Free 6-Lead MicroPak, 1.0mm Wide 5k Units on Tape and Reel Note 1: “_NL” indicates Pb-Free product (per JEDEC J-STD-020B). Device is available in Tape and Reel only. TinyLogic£ is a registered trademark of Fairchild Semiconductor Corporation. MicroPak¥ is a trademark of Fairchild Semiconductor Corporation. © 2005 Fairchild Semiconductor Corporation DS012141 www.fairchildsemi.com NC7S08 Logic Symbol IEEE/IEC Connection Diagrams Pin Assignments for SC70 and SOT23 Pin Descriptions Pin Names A, B Y NC Description Inputs Output No Connect Pad Assignments for MicroPak (Top View) Function Table Y Inputs A L L H H H HIGH Logic Level L AB Output B L H L H LOW Logic Level Y L L L H (Top Thru View) www.fairchildsemi.com 2 NC7S08 Absolute Maximum Ratings(Note 2) Supply Voltage (VCC) 0.5V to 7.0V DC Input Diode Current (IIK) @ VIN t VCC 0.5V DC Input Voltage (VIN ) DC Output Diode Current (IOK) @ VOUT ! VCC 0.5V DC Output Voltage (VOUT) DC Output Source or Sink Current (IOUT) DC VCC or Ground Current per Output Pin (ICC or IGND) Storage Temperature (TSTG) Junction Temperature (TJ) Lead Temperature (TL); Power Dissipation (PD) @85qC SOT23-5 SC70-5 (Soldering, 10 seconds) @ VOUT  0.5V @ VIN d 0.5V Recommended Operating Conditions (Note 3) Supply Voltage (VCC) Input Voltage (VIN) Output Voltage (VOUT) Operating Temperature (TA) Input Rise and Fall Time (tr, tf) VCC @ 2.0V VCC @ 3.0V VCC @ 4.5V Thermal Resistance (TJA) SOT23-5 SC70-5 VCC @ 6.0V 0 to 1000 ns 0 to 750 ns 0 to 500 ns 0 to 400 ns 300qC/W 425qC/W 2.0V to 6.0V 0V to VCC 0V to VCC 20 mA 20 mA 0.5V to VCC  0.5V 20 mA 20 mA 0.5V to VCC  0.5V r12.5 mA r25 mA 65qC to 150qC 150qC 260qC 200 mW 150 mW 40qC to 85qC Note 2: Absolute maximum ratings are those values beyond which damage to the device may occur. The databook specifications should be met, without exception, to ensure that the system design is reliable over its power supply, temperature, and output/input loading variables. Fairchild does not recommend operation of circuits outside databook specifications. Note 3: Unused inputs must be held HIGH or LOW. They may not float. DC Electrical Characteristics Symbol VIH VIL VOH Parameter HIGH Level Input Voltage LOW Level Input Voltage HIGH Level Output Voltage VCC (V) 2.0 3.0-6.0 2.0 3.0-6.0 2.0 3.0 4.5 6.0 3.0 4.5 6.0 VOL LOW Level Output Voltage 2.0 3.0 4.5 6.0 3.0 4.5 6.0 IIN ICC Input Leakage Current Quiescent Supply Current 6.0 6.0 1.90 2.90 4.40 5.90 2.68 4.18 5.68 2.0 3.0 4.5 6.0 2.85 4.35 5.85 0.0 0.0 0.0 0.0 0.1 0.1 0.1 0.10 0.10 0.10 0.10 0.26 0.26 0.26 Min 1.50 0.7 VCC 0.50 0.3 VCC 1.90 2.90 4.40 5.90 VIN 2.63 4.13 5.63 0.10 0.10 0.10 0.10 VIN 0.33 0.33 0.33 V IOH IOL IOL VIN VIN VIH or VIL 1.3 mA 2 mA 2.6 mA VCC, GND VCC, GND V IOL VIN 20 PA VIL V IOH IOH IOH VIH V IOH VIN TA 25qC Typ Max TA 40qC to 85qC Max Min 1.50 0.7 VCC Units V Conditions 0.50 0.3 VCC V 20 PA VIH 1.3 mA 2 mA 2.6 mA r0.1 1.0 r1.0 10.0 PA PA 3 www.fairchildsemi.com NC7S08 AC Electrical Characteristics Symbol tPLH, tPHL Parameter Propagation Delay VCC (V) 5.0 2.0 3.0 4.5 6.0 tTLH, tTHL Output Transition Time 5.0 2.0 3.0 4.5 6.0 CIN CPD Input Capacitance Power Dissipation Capacitance Open 5.0 Min TA 25qC Typ 3.5 20 11 8 7 3.0 25 16 11 9 2 6 Max 15 100 27 20 17 10 125 35 25 21 10 TA 40qC to 85qC Max 125 35 25 21 Min Units ns Conditions CL 15 pF Figure Number ns CL 50 pF Figures 1, 3 ns 155 45 31 26 10 pF pF ns CL 15 pF Figures 1, 3 CL 50 pF (Note 4) Figure 2 Note 4: CPD is defined as the value of the internal equivalent capacitance which is derived from dynamic operating current consumption (ICCD) at no output loading and operating at 50% duty cycle. (See Figure 2.) CPD is related to ICCD dynamic operating current by the expression: ICCD (CPD)(VCC)(fIN)  (ICCstatic). AC Loading and Waveforms CL includes load and stray capacitance Input PRR 1.0 MHz; tW 500 ns FIGURE 1. AC Test Circuit FIGURE 3. AC Waveforms Input PRR AC Waveform; variable; Duty Cycle 50% FIGURE 2. ICCD Test Circuit www.fairchildsemi.com 4 NC7S08 Tape and Reel Specification TAPE FORMAT for SC70 and SOT23 Package Tape Designator M5X, P5X Section Leader (Start End) Carrier Trailer (Hub End) TAPE DIMENSIONS inches (millimeters) Number Cavities 125 (typ) 3000 75 (typ) Cavity Status Empty Filled Empty Cover Tape Status Sealed Sealed Sealed Package SC70-5 SOT23-5 Tape Size 8 mm 8 mm DIM A 0.093 (2.35) 0.130 (3.3) DIM B 0.096 (2.45) 0.130 (3.3) DIM F (3.5 r 0.10) 0.138 r 0.004 0.053 r 0.004 0.138 r 0.002 0.055 r 0.004 (3.5 r 0.05) (1.4 r 0.11) (1.35 r 0.10) DIM Ko DIM P1 0.157 (4) 0.157 (4) DIM W 0.315 r 0.004 0.315 r 0.012 (8 r 0.3) (8 r 0.1) 5 www.fairchildsemi.com NC7S08 Tape and Reel Specification TAPE FORMAT for MicroPak Package Designator L6X Tape Section Leader (Start End) Carrier Trailer (Hub End) (Continued) Number Cavities 125 (typ) 5000 75 (typ) Cavity Status Empty Filled Empty Cover Tape Status Sealed Sealed Sealed REEL DIMENSIONS inches (millimeters) Tape Size 8 mm A 7.0 (177.8) B 0.059 (1.50) C 0.512 (13.00) D 0.795 (20.20) N 2.165 (55.00) W1 0.331  0.059/0.000 (8.40  1.50/0.00) W2 0.567 (14.40) W3 W1  0.078/0.039 (W1  2.00/1.00) www.fairchildsemi.com 6 NC7S08 Physical Dimensions inches (millimeters) unless otherwise noted 5-Lead SOT23, JEDEC MO-178, 1.6mm Package Number MA05B 7 www.fairchildsemi.com NC7S08 Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 5-Lead SC70, EIAJ SC-88a, 1.25mm Wide Package Number MAA05A www.fairchildsemi.com 8 NC7S08 TinyLogic£ HS 2-Input AND Gate Physical Dimensions inches (millimeters) unless otherwise noted (Continued) Pb-Free 6-Lead MicroPak, 1.0mm Wide Package Number MAC06A Fairchild does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and Fairchild reserves the right at any time without notice to change said circuitry and specifications. LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 9 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. www.fairchildsemi.com www.fairchildsemi.com