KBPC10XX

www.DataSheet4U.com Data Sheet 10 to 40 Amp SINGLE PHASE SILICON BRIDGE Description Features n BUILT-IN INTEGRAL HEAT SINK n UL RECOGNITION AVAILABLE n UP TO 400 AMP SURGE OVERLOAD RATING n OPTION OF WIRE LEADS OR FASTON TERMINALS KBPC10 . . . 40XX Series -00 50 35 50 KBPC10 KBPC15 KBPC25 KBPC35 KBPC40 -01 100 70 100 -02 200 140 200 -04 400 280 400 10 15 25 35 40 -06 600 420 600 -08 800 560 800 -10 1000 700 1000 -12 1200 840 1200 Electrical Characteristics @ 25o C. Maximum Ratings Peak Repetitive Reverse Voltage...VRRM RMS Reverse Voltage...VR(rms) DC Blocking Voltage...VDC Average Forward Rectified Current...IF(av) Units Volts Volts Volts Amps Amps Amps Amps Amps KBPC10 KBPC15 KBPC25 KBPC35 KBPC40 Forward Voltage...VF KBPC10, IF = 5A KBPC15, IF = 7.5A KBPC25, IF = 12.5A KBPC35, IF = 17.5A KBPC40, IF = 20.0A Isolation Voltage Case to Leads...VISO DC Reverse Current...IR @ Rated DC Blocking Voltage per Leg TA = 25°C TA = 125°C Typical Thermal Resistance...RθJC Junction to Case per Leg Typical Junction Capacitance...CJ Operating & Storage Temperature Range...TJ, TSTRG Non-Repetitive Peak Forward Surge Current...IFSM ............................................. ............................................. ............................................. ............................................. ............................................. ............................................. ............................................. ............................................. ............................................. ............................................. ............................................. ............................................. ............................................. ............................................. ............................................. ............................................. ............................................... ............................................... ............................................... ............................................... ............................................... 200 ............................................... Amps 300 ............................................... Amps 300 ............................................... Amps 400 ............................................... Amps 400 ............................................... Amps 1.1 ............................................... Volts 1.1 ............................................... Volts 1.1 ............................................... Volts 1.1 ............................................... Volts 1.1 ............................................... Volts 2500 ............................................... Volts AC µAmps µAmps °C / W pF °C ............................................. 5.0 ............................................... ............................................. 500 ............................................... ............................................. 1.9 ............................................... ............................................. 300 ............................................... ......................................... -55 to150 .......................................... Page 3-28 KBPC10XX . . . 40XX Series Data Sheet 10 to 40 Amp SINGLE PHASE SILICON BRIDGE KBPC10XX . . . 40XX Series Instantaneous Forward Characteristics Typical Reverse Characteristics Page 3-29 NOTES: 1. Reverse Recovery Cond., If = .5A, Ir = 1.0A, Irr = .25A. 2. Thermal Resistance Junction to Ambient, Jedec Method. 3. When Mounted to heat sink, from body. Data Sheet 10 to 40 Amp SINGLE PHASE SILICON BRIDGE Mechanical Dimensions Ratings at 25 Deg. C ambient temperature unless otherwise specified. Single Phase Half Wave, 60 HZ Resistive or Inductive Load. For Capacitive Load, Derate Current by 20%. NOTES: 1 . Corrosion-Resistant Terminals Designed for .250" Female Quick Connect Wrap Around or Solder. 2 . A Thin Film of Silicone Thermal Compound is Recommended Between Bridge and Mounting Surface for Improved Thermal Conduction. 3 . These FCI Bridges Are Also Available in Fast Recovery, In Positive and Negative Center Tap and in Double Configurations. Consult with FCI for Your Special Requirements. Page 3-30 KBPC10XX . . . 40XX Series Data Sheet 10 to 40 Amp SINGLE PHASE SILICON BRIDGE KBPC10XX . . . 40XX Series Case - Metal or Molded Plastic AC In Terminals - Plated .25" Faston or Plated Copper Wire Leads .040" Diameter Weight - 0.706 Ounces, 20 Grams DC Out Mounting Position - Any with Bolt Down with Silicone Thermal Compound Between Bridge and Mounting Surface for Optimum Heat Transfer Mounting Torque - 20 Inch Pound Max FCI’S KBPC Series of Bridges Can Be Ordered with Options on Terminals and Case Materials. How To Specify Case Material and Terminal Options: n For Metal Case, Order Suffix (1) “M” n For Plastic Case, Order Suffix (1) “P” n For Faston Terminals, Order Suffix (2) “F” n For Wire Lead Terminals, Order Suffix (2) “W” n For a UL Recognized Device, Order Suffix (3) “U” Ordering Information KBPC Series Examples To Order a 25 Amp, 400 Volt Bridge with Faston Leads and a Plastic Case: Specify - KBPC2504PF . . . Where “P” = Plastic and “F” = Faston Terminals To Order a 35 Amp, 800 Volt Bridge with Wire Leads and a Metal Case: Specify - KBPC3508MW . . . Where “M” = Metal and “W” = Wire Leads (Terminals) To Order a 15 Amp, 200 Volt, UL Recognized Bridge with Wire Leads and a Plastic Case: Specify - KBPC1502PWU . . . Where “P” = Plastic and “W” = Wire Leads (Terminals) and “U” = UL Recognized NOTE: Fast Recovery Bridges (Diodes) Are Available; Please Contact FCI Components. KBPC - “S” Series Examples To Order Bridges with the “In-Line” Pin Configuration, Select the Current and Voltage Desired and Add “S” as the Suffix, as shown in the following example. To Order a 35 Amp, 800 Volt Bridge with In-Line Wire Leads: Specify - KBPC3508S . . . Where “S” = In-Line Wire Lead Terminals Page 3-31