E32-3F3-A315-E

FERROXCUBE DATA SHEET E32/6/20 Planar E cores and accessories Supersedes data of September 2004 2008 Sep 01 Ferroxcube Planar E cores and accessories CORES Effective core parameters of a set of E cores SYMBOL Σ(I/A) Ve Ie Ae Amin m PARAMETER core factor (C1) effective volume effective length effective area minimum area mass of core half VALUE 0.323 5380 41.4 130 130 ≈ 13 UNIT mm−1 mm3 mm mm2 mm2 g R0.25 typ. handbook, halfpage E32/6/20 31.75 ±0.64 24.9 min. 6.35 ±0.13 3.18 ±0.2 6.35 ±0.13 20.32 ±0.41 R0.64 ref. typ. CBW407 Dimensions in mm. Fig.1 E32/6/20. Effective core parameters of an E/PLT combination SYMBOL Σ(I/A) Ve Ie Ae Amin m PARAMETER core factor (C1) effective volume effective length effective area minimum area mass of plate VALUE 0.278 4560 35.1 130 130 ≈ 10 UNIT mm−1 mm3 mm mm2 mm2 g handbook, halfpage 31.75 ±0.64 3.18 ±0.13 Ordering information for plates GRADE 3C90 3C92 3C93 3C94 3C95 3C96 3F3 3F4 TYPE NUMBER PLT32/20/3.2-3C90 PLT32/20/3.2-3C92 PLT32/20/3.2-3C93 PLT32/20/3.2-3C94 PLT32/20/3.2-3C95 PLT32/20/3.2-3C96 PLT32/20/3.2-3F3 PLT32/20/3.2-3F4 Dimensions in mm. 20.32 ±0.41 R0.64 ref. typ. CBW408 Fig.2 PLT32/20/3.2. 2008 Sep 01 2 Ferroxcube Planar E cores and accessories E32/6/20 Core halves for use in combination with an E core AL measured in combination with a non-gapped core half, clamping force for AL measurements, 30 ±10 N, unless stated otherwise. GRADE 3C90 AL (nH) 160 ±3%(1) 250 ±3%(1) 315 ±3% 400 ±5% 630 ±8% 6425 ±25% 3C92 3C93 3C94 5000 ±25% 5900 ±25% 160 ±3%(1) 250 ±3%(1) 315 ±3% 400 ±5% 630 ±8% 6425 ±25% 3C95 3C96 3F3 7690 ±25% 6425 ±25% 160 ±3%(1) 250 ±3%(1) 315 ±3% 400 ±5% 630 ±8% 5900 ±25% 3F4 160 ±3%(1) 250 ±3%(1) 315 ±3% 400 ±5% 630 ±8% 3200 ±25% Note 1. Measured in combination with an equal gapped E core half, clamping force for AL measurements, 30 ±10 N. µe ≈ 41 ≈ 64 ≈ 81 ≈ 103 ≈ 162 ≈ 1 650 ≈ 1 290 ≈ 1520 ≈ 41 ≈ 64 ≈ 81 ≈ 103 ≈ 162 ≈ 1 650 ≈ 1950 ≈ 1 650 ≈ 41 ≈ 64 ≈ 81 ≈ 103 ≈ 162 ≈ 1 520 ≈ 41 ≈ 64 ≈ 81 ≈ 103 ≈ 162 ≈ 820 TOTAL AIR GAP (µm) ≈ 1200 ≈ 700 ≈ 550 ≈ 450 ≈ 260 ≈0 ≈0 ≈0 ≈ 1200 ≈ 700 ≈ 550 ≈ 450 ≈ 260 ≈0 ≈0 ≈0 ≈ 1200 ≈ 700 ≈ 550 ≈ 450 ≈ 260 ≈0 ≈ 1200 ≈ 700 ≈ 550 ≈ 450 ≈ 260 ≈0 TYPE NUMBER E32/6/20-3C90-E160-E E32/6/20-3C90-E250-E E32/6/20-3C90-A315-E E32/6/20-3C90-A400-E E32/6/20-3C90-A630-E E32/6/20-3C90 E32/6/20-3C92 E32/6/20-3C93 E32/6/20-3C94-E160-E E32/6/20-3C94-E250-E E32/6/20-3C94-A315-E E32/6/20-3C94-A400-E E32/6/20-3C94-A630-E E32/6/20-3C94 E32/6/20-3C95 E32/6/20-3C96 E32/6/20-3F3-E160-E E32/6/20-3F3-E250-E E32/6/20-3F3-A315-E E32/6/20-3F3-A400-E E32/6/20-3F3-A630-E E32/6/20-3F3 E32/6/20-3F4-E160-E E32/6/20-3F4-E250-E E32/6/20-3F4-A315-E E32/6/20-3F4-A400-E E32/6/20-3F4-A630-E E32/6/20-3F4 2008 Sep 01 3 Ferroxcube Planar E cores and accessories Core halves for use in combination with a plate (PLT) AL measured in combination with a plate (PLT), clamping force for AL measurements, 30 ±10 N. GRADE 3C90 AL (nH) 160 ±3% 250 ±3% 315 ±3% 400 ±5% 630 ±8% 7350 ±25% 3C92 3C93 3C94 5760 ±25% 6780 ±25% 160 ±3% 250 ±3% 315 ±3% 400 ±5% 630 ±8% 7350 ±25% 3C95 3C96 3F3 8750 ±25% 7350 ±25% 160 ±3% 250 ±3% 315 ±3% 400 ±5% 630 ±8% 6780 ±25% 3F4 160 ±3% 250 ±3% 315 ±3% 400 ±5% 630 ±8% 3700 ±25% µe ≈ 35 ≈ 55 ≈ 69 ≈ 87 ≈ 138 ≈ 1 610 ≈ 1270 ≈ 1 500 ≈ 35 ≈ 55 ≈ 69 ≈ 87 ≈ 138 ≈ 1 610 ≈ 1880 ≈ 1 610 ≈ 35 ≈ 55 ≈ 69 ≈ 87 ≈ 138 ≈ 1 490 ≈ 35 ≈ 55 ≈ 69 ≈ 87 ≈ 138 ≈ 810 AIR GAP (µm) ≈ 1200 ≈ 700 ≈ 550 ≈ 450 ≈ 260 ≈0 ≈0 ≈0 ≈ 1200 ≈ 700 ≈ 550 ≈ 450 ≈ 260 ≈0 ≈0 ≈0 ≈ 1200 ≈ 700 ≈ 550 ≈ 450 ≈ 260 ≈0 ≈ 1200 ≈ 700 ≈ 550 ≈ 450 ≈ 260 ≈0 E32/6/20 TYPE NUMBER E32/6/20-3C90-A160-P E32/6/20-3C90-A250-P E32/6/20-3C90-A315-P E32/6/20-3C90-A400-P E32/6/20-3C90-A630-P E32/6/20-3C90 E32/6/20-3C92 E32/6/20-3C93 E32/6/20-3C94-A160-P E32/6/20-3C94-A250-P E32/6/20-3C94-A315-P E32/6/20-3C94-A400-P E32/6/20-3C94-A630-P E32/6/20-3C94 E32/6/20-3C95 E32/6/20-3C96 E32/6/20-3F3-A160-P E32/6/20-3F3-A250-P E32/6/20-3F3-A315-P E32/6/20-3F3-A400-P E32/6/20-3F3-A630-P E32/6/20-3F3 E32/6/20-3F4-A160-P E32/6/20-3F4-A250-P E32/6/20-3F4-A315-P E32/6/20-3F4-A400-P E32/6/20-3F4-A630-P E32/6/20-3F4 2008 Sep 01 4 Ferroxcube Planar E cores and accessories Properties of core sets under power conditions B (mT) at GRADE H = 250 A/m; f = 10 kHz; T = 100 °C ≥320 ≥320 ≥370 ≥370 ≥320 ≥320 ≥320 ≥320 ≥320 ≥320 ≥320 ≥320 ≥300 ≥300 ≥250 ≥250 f = 100 kHz; ˆ B = 100 mT; T = 100 °C ≤ 0.65 ≤ 0.55 ≤ 0.48 ≤ 0.41 ≤ 0.48 (1) ≤ 0.41 (1) ≤ 0.48 ≤ 0.41 − − ≤ 0.36 ≤ 0.3 ≤ 0.65 ≤ 0.6 − − CORE LOSS (W) at f = 100 kHz; ˆ B = 200 mT; T = 25 °C − − − − − − − − ≤ 3.17 ≤ 2.69 − − − − − − f = 100 kHz; ˆ B = 200 mT; T = 100 °C − − ≤ 3.4 ≤ 2.9 ≤ 3.4 (1) ≤ 2.9 (1) ≤ 3.4 ≤ 2.9 ≤ 3.0 ≤ 2.55 ≤ 2.6 ≤ 2.2 − − − − E32/6/20 f = 400 kHz; ˆ B = 50 mT; T = 100 °C − − − − − − − − − − ≤ 0.9 ≤ 0.8 ≤ 1.0 ≤ 0.85 − − E+E32-3C90 E+PLT32-3C90 E+E32-3C92 E+PLT32-3C92 E+E32-3C93 E+PLT32-3C93 E+E32-3C94 E+PLT32-3C94 E+E32-3C95 E+PLT32-3C95 E+E32-3C96 E+PLT32-3C96 E+E32-3F3 E+PLT32-3F3 E+E32-3F4 E+PLT32-3F4 Measured at 140 °C. 1. Properties of core sets under power conditions (continued) B (mT) at GRADE H = 250 A/m; f = 10 kHz; T = 100 °C ≥320 ≥320 ≥300 ≥300 ≥250 ≥250 f = 500 kHz; ˆ B = 50 mT; T = 100 °C ≤ 2.0 ≤ 1.7 − − − − CORE LOSS (W) at f = 500 kHz; ˆ B = 100 mT; T = 100 °C − − − − − − f = 1 MHz; ˆ B = 30 mT; T = 100 °C − − − − ≤ 1.6 ≤ 1.36 f = 3 MHz; ˆ B = 10 mT; T = 100 °C − − − − ≤ 2.5 ≤ 2.2 E+E32-3C96 E+PLT32-3C96 E+E32-3F3 E+PLT32-3F3 E+E32-3F4 E+PLT32-3F4 2008 Sep 01 5 Ferroxcube Planar E cores and accessories DATA SHEET STATUS DEFINITIONS DATA SHEET STATUS Preliminary specification Product specification PRODUCT STATUS Development DEFINITIONS E32/6/20 This data sheet contains preliminary data. Ferroxcube reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. This data sheet contains final specifications. Ferroxcube reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Production DISCLAIMER Life support applications  These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Ferroxcube customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Ferroxcube for any damages resulting from such application. PRODUCT STATUS DEFINITIONS STATUS Prototype Design-in Preferred Support INDICATION DEFINITION These are products that have been made as development samples for the purposes of technical evaluation only. The data for these types is provisional and is subject to change. These products are recommended for new designs. These products are recommended for use in current designs and are available via our sales channels. These products are not recommended for new designs and may not be available through all of our sales channels. Customers are advised to check for availability. 2008 Sep 01 6