RM6R-3H3-A315

FERROXCUBE DATA SHEET RM6R RM, RM/I, RM/ILP cores and accessories Supersedes data of September 2004 2008 Sep 01 Ferroxcube RM, RM/I, RM/ILP cores and accessories CORE SETS Effective core parameters SYMBOL Σ(I/A) Ve Ie Ae Amin m PARAMETER core factor (C1) effective volume effective length effective area minimum area mass of set VALUE 0.810 810 25.6 32.0 23.8 ≈ 4.5 UNIT mm−1 mm3 mm mm2 mm2 g M1.7 17.9 0 −0.7 ∅6.4 0 −0.2 handbook, halfpage RM6R 14.7 0 −0.6 0 2.9 −0.4 7.4 ∅3 +0.1 0 10.35 ±0.2 2.3 8 +0.4 12.4 0 ±0.1 ∅12.4 +0.5 0 Dimensions in mm. CBW128 Fig.1 RM6R core set. Core sets for filter applications Clamping force for AL measurements, 40 ±20 N. GRADE 3D3 AL (nH) 40 ±3% 63 ±3% 100 ±3% 160 ±3% 1000 ±25% 3H3 160 ±3% 250 ±3% 315 ±3% 400 ±3% 2200 ±25% µe ≈ 26 ≈ 41 ≈ 65 ≈ 103 ≈ 650 ≈ 103 ≈ 161 ≈ 203 ≈ 258 ≈ 1 420 TOTAL AIR GAP (µm) ≈ 1 200 ≈ 700 ≈ 400 ≈ 200 ≈0 ≈ 230 ≈ 110 ≈ 90 ≈ 70 ≈0 TYPE NUMBER (WITH NUT) RM6R-3D3-E40/N RM6R-3D3-E63/N RM6R-3D3-E100/N RM6R-3D3-A160/N − RM6R-3H3-A160/N RM6R-3H3-A250/N RM6R-3H3-A315/N RM6R-3H3-A400/N − TYPE NUMBER (WITHOUT NUT) RM6R-3D3-E40 RM6R-3D3-E63 RM6R-3D3-E100 RM6R-3D3-A160 RM6R-3D3 RM6R-3H3-A160 RM6R-3H3-A250 RM6R-3H3-A315 RM6R-3H3-A400 RM6R-3H3 2008 Sep 01 1202 Ferroxcube RM, RM/I, RM/ILP cores and accessories INDUCTANCE ADJUSTER General data PARAMETER Material of head and thread Maximum operating temperature SPECIFICATION polypropylene (PP), glass fibre reinforced 125 °C 9.5 handbook, halfpage RM6R 0.07 O 3.13 0 3.4 M 1.7 0.7 2.4 min MGC079 Dimensions in mm. Fig.2 RM6R inductance adjuster. Inductance adjuster selection chart GRADE 3H3 AL (nH) 40 − 63 − 100 ADJ-RM6-GREEN 160 ADJ-RM6-GREEN 200 ADJ-RM6-RED 250 ADJ-RM6-WHITE 315 ADJ-RM6-WHITE 400 ADJ-RM6-VIOLET 630 ADJ-RM6-BLACK 1000 ADJ-RM6-BLACK 1250 − 3D3 40 − 63 − 100 ADJ-RM6-GREEN 160 ADJ-RM6-RED Note 1. Maximum adjustment range. TYPES FOR LOW ADJUSTMENT (applies to all types) ∆L/L(1) TYPES FOR MEDIUM ∆L/L(1) % ADJUSTMENT % − − 10 6 8 12 9 8 9 5 − − − 9 10 − ADJ-RM6-GREEN ADJ-RM6-RED ADJ-RM6-RED ADJ-RM6-WHITE ADJ-RM6-VIOLET ADJ-RM6-BROWN ADJ-RM6-BLACK ADJ-RM6-GREY ADJ-RM6-GREY ADJ-RM6-GREY − ADJ-RM6-GREEN ADJ-RM6-RED ADJ-RM6-WHITE − 14 16 10 15 14 15 16 15 8 5 − 14 16 17 TYPES FOR HIGH ADJUSTMENT ADJ-RM6-GREEN ADJ-RM6-RED − ADJ-RM6-WHITE ADJ-RM6-VIOLET ADJ-RM6-BROWN ADJ-RM6-BLACK ADJ-RM6-GREY − − − ADJ-RM6-GREEN ADJ-RM6-RED ADJ-RM6-WHITE − ∆L/L(1) % 20 22 − 19 18 20 22 30 − − − 20 23 28 − 2008 Sep 01 1203 Ferroxcube RM, RM/I, RM/ILP cores and accessories COIL FORMERS General data PARAMETER Coil former material Pin material Maximum operating temperature Resistance to soldering heat Solderability SPECIFICATION phenolformaldehyde (PF), glass-reinforced, flame retardant in accordance with “UL 94V-0”; UL file number E167521(M) copper-tin alloy (CuSn), tin (Sn) plated 180 °C, “IEC 60085”, class H “IEC 60068-2-20” , Part 2, Test Tb, method 1B, 350 °C, 3.5 s ‘‘IEC 60068-2-20”, Part 2, Test Ta, method 1 RM6R handbook, full pagewidth 12.7 7.62 1.6 0.4 2 3 0 7.8 0.15 (6.4 min) 0 0.8 0.1 0.75 O 0.6 2.54 0.15 6.5 0 1 8.6 5.7 max 4 1.4 min 0 0 O 12.3 0.2 O 7.45 0.2 0.4 5.2 1 0.15 0 MGC080 Dimensions in mm. Fig.3 RM6R coil former; 4-pins. Winding data and area product for 4-pins RM6R coil former NUMBER OF SECTIONS 1 2 NUMBER OF PINS 4 4 PIN POSITIONS USED all all AVERAGE LENGTH OF TURN (mm) 30 30 WINDING AREA (mm2) 15 2 × 7.0 WINDING WIDTH (mm) 6.4 2 × 3.0 AREA PRODUCT Ae x Aw (mm 4) 480 2 x 224 TYPE NUMBER CSV-RM6S/R-1S-4P CSV-RM6S/R-2S-4P 2008 Sep 01 1204 Ferroxcube RM, RM/I, RM/ILP cores and accessories RM6R handbook, full pagewidth 12.7 7.62 1.6 0.7 min 3 4 5 0.4 0 7.8 0.15 (6.4 min) 0 0.8 0.1 0.75 O 0.6 2.54 6.5 0.15 0 2 8.6 5.7 max 1 6 12.3 0 0 0.2 O 7.45 0.2 0.4 5.2 1 0.15 0 MGC081 Dimensions in mm. Fig.4 RM6R coil former; 6-pins. Winding data and area product for 6-pins RM6R coil former NUMBER OF SECTIONS 1 2 NUMBER OF PINS 6 6 PIN POSITIONS USED all all AVERAGE LENGTH OF TURN (mm) 30 30 WINDING AREA (mm2) 15 2 × 7.0 WINDING WIDTH (mm) 6.4 2 × 3.0 AREA PRODUCT Ae x Aw (mm4) 480 2 x 224 TYPE NUMBER CSV-RM6R-1S-6P CSV-RM6R-2S-6P MOUNTING PARTS handbook, halfpage General data ITEM Clamping force Clip material Clip plating Solderability Type number ≈ 20 N steel silver (Ag) “IEC 60 068-2-20”, Part 2, Test Ta, method 1 CLI/P-RM6 SPECIFICATION 2.3 1.6 12 9.8 0.7 MGC082 4.5 Dimensions in mm. Fig.5 Mounting clip for RM6R. 2008 Sep 01 1205 Ferroxcube RM, RM/I, RM/ILP cores and accessories DATA SHEET STATUS DEFINITIONS DATA SHEET STATUS Preliminary specification Product specification PRODUCT STATUS Development DEFINITIONS RM6R This data sheet contains preliminary data. Ferroxcube reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. This data sheet contains final specifications. Ferroxcube reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Production DISCLAIMER Life support applications  These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Ferroxcube customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Ferroxcube for any damages resulting from such application. PRODUCT STATUS DEFINITIONS STATUS Prototype Design-in Preferred Support INDICATION DEFINITION These are products that have been made as development samples for the purposes of technical evaluation only. The data for these types is provisional and is subject to change. These products are recommended for new designs. These products are recommended for use in current designs and are available via our sales channels. These products are not recommended for new designs and may not be available through all of our sales channels. Customers are advised to check for availability. 2008 Sep 01 1206