FMA3007

FMA3007 2-20GHZ BROADBAND MMIC AMPLIFIER FEATURES: • • • • • • 17 dBm Output Power 11 dB Gain pHEMT Technology Input Return Loss < -13dB Output Return Loss < -11dB Voltage Gain Control Production Datasheet v3.0 FUNCTIONAL SCHEMATIC: VG2 VDD RF Input RF Output VG1 GENERAL DESCRIPTION: The FMA3007 is a high performance 2-20GHz Gallium Arsenide monolithic travelling wave amplifier. It is suitable for use in broadband communication, instrumentation and electronic warfare applications. The die is fabricated using the Filtronic 0.25µm process. TYPICAL APPLICATIONS: • • • Test Instrumentation Electronic Warfare Broadband Communication Infrastructure ELECTRICAL SPECIFICATIONS: PARAMETER Small Signal Gain Small Signal Gain Input Return Loss Output Return Loss Reverse Isolation Output Power at 1dB compression point CONDITIONS 1, 2, 3 2-12GHz 12-20GHz 2-20GHz 2-20GHz 2-20GHz 2GHz 10GHz 20GHz MIN 9.5 9.5 16 18 14 60 - TYP 10.5 11.5 19 19 16 4.5 100 3.5 MAX 11.5 12.5 -13 -11 -27 8.5 5.5 150 - UNITS dB dB dB dB dB dBm dBm dBm dB dB mA V Noise Figure Noise Figure Drain Current Drain Voltage 2-4.5 GHz 4.5-20 GHz For Vdd = 3.5V , Vg1 = -0.38V , Vg2=+1V Notes: 1. TAmbient = +25°C 2. Device is biased at constant gate voltage, measured on wafer with Z0 = 50Ω 3. Measurement Conditions VG1= -0.38V, VDD= 3.5V, VG2=+1V. 1 Specifications subject to change without notice Filtronic Compound Semiconductors Ltd Fax: +44 (0) 1325 306177 Email: sales@filcs.com Tel: +44 (0) 1325 301111 Website: www.filtronic.com FMA3007 Production Datasheet v3.0 ABSOLUTE MAXIMUM RATINGS: PARAMETER Max Input Power Gate Voltage Drain Voltage Total Power Dissipation Gain Compression Thermal Resistivity Operating Temp Storage Temp SYMBOL Pin VG1 VDD ABSOLUTE MAXIMUM +20dBm PAD REF A PAD NAME RF in VDP DESCRIPTION PIN COORDINATES (µm) (140, 1153) (2097, 140) RF in (+Ve) Temperature Monitoring Diode -2V B +10V C VDN (-Ve) Temperature Monitoring Diode Ptot tbd (2321, 140) Comp tbd 38°C/W -40°C to +85°C -55°C to +150°C D E F G H GND VG1 VG2 RF Out GND VDD Ground Gate Control Gain Control RF Out Ground Drain Voltage (2545, 140) (2769, 140) (2993, 140) (3004, 1141) (2800, 1650) (2550, 1650) θJC Toper Tstor Note: Exceeding any one of these absolute maximum ratings may cause permanent damage to the device. I Note: Co-ordinates are referenced from the bottom left hand corner of the die to the centre of bond pad opening PAD LAYOUT: I A H G B C D E F DIE SIZE (µm) 3150 x 1780 DIE THICKNESS (µm) 100 MIN. BOND PAD PITCH (µm) 220 MIN. BOND PAD OPENING (µm x µm ) 100 x 100 2 Specifications subject to change without notice Filtronic Compound Semiconductors Ltd Fax: +44 (0) 1325 306177 Email: sales@filcs.com Tel: +44 (0) 1325 301111 Website: www.filtronic.com FMA3007 Production Datasheet v3.0 TYPICAL PERFORMANCE FOR ON WAFER MEASUREMENTS: Note: Measurement Conditions VG1= -0.38V, VDD= 3.5V, VG2=+1V, TAMBIENT = 25°C P1dB 20 P 1 d B (d B m ) 15 10 5 0 2 4 6 8 10 12 14 16 18 20 Fre que ncy (GHz) Gain vs VG2 C ontrol Voltage 10 Freq = 10 GHz 8 Gain (dB) 6 4 2 0 -0.5 -0.4 -0.3 -0.2 -0.1 0 Vg2(V)Voltage 0.1 0.2 0.3 0.4 3 Specifications subject to change without notice Filtronic Compound Semiconductors Ltd Fax: +44 (0) 1325 306177 Email: sales@filcs.com Tel: +44 (0) 1325 301111 Website: www.filtronic.com FMA3007 Production Datasheet v3.0 TYPICAL MEASURED PERFORMANCE FOR ON WAFER TEMPERATURE MEASUREMENTS: Note: Measurement Conditions VG1= -0.38V, VDD= 3.5V, VG2= +1V, TAMBIENT = -40°C to +85°C 4 Specifications subject to change without notice Filtronic Compound Semiconductors Ltd Fax: +44 (0) 1325 306177 Email: sales@filcs.com Tel: +44 (0) 1325 301111 Website: www.filtronic.com FMA3007 Production Datasheet v3.0 S-PARAMETERS FOR ON-WAFER MEASUREMENTS: Note: Measurement Conditions VDD= 3.5V, Vg1=-0.38V and Vg2=1V S11 Frequenc y Mag 2 2. 19 2. 38 2. 57 2. 76 2. 95 3. 14 3. 33 3. 52 3. 71 3. 9 4. 09 4. 28 4. 47 4. 66 4. 85 5. 04 5. 23 5. 42 5. 61 5. 8 5. 99 6. 18 6. 37 6. 56 6. 75 6. 94 7. 13 7. 32 7. 51 7. 7 7. 89 8. 08 8. 27 8. 46 8. 65 8. 84 9. 03 9. 22 9. 41 9. 6 9. 79 9. 98 10. 17 10. 36 10. 55 10. 74 10. 93 Angle 0. 17 0. 17 0. 16 0. 15 0. 14 0. 13 0. 12 0. 11 0. 11 0. 10 0. 09 0. 08 0. 08 0. 07 0. 06 0. 05 0. 05 0. 04 0. 03 0. 02 0. 02 0. 01 0. 00 0. 00 0. 01 0. 02 0. 02 0. 03 0. 04 0. 04 0. 05 0. 05 0. 06 0. 07 0. 07 0. 08 0. 08 0. 09 0. 09 0. 09 0. 10 0. 10 0. 10 0. 11 0. 11 0. 11 0. 11 0. 11 7. 23 2. 14 -4. 69 -10. 51 -15. 56 -20. 19 -24. 56 -28. 52 -32. 28 -36. 00 -39. 67 -43. 21 -46. 86 -50. 51 -53. 98 -57. 63 -60. 76 -63. 54 -66. 22 -68. 53 -68. 00 -64. 51 -42. 62 39. 78 17. 49 16. 81 15. 13 84. 08 82. 14 79. 53 76. 81 74. 57 72. 42 69. 51 66. 45 64. 01 60. 83 58. 56 55. 69 52. 28 48. 64 45. 29 41. 97 38. 97 36. 22 33. 38 30. 10 26. 91 S 21 Mag 3. 47 3. 45 3. 43 3. 42 3. 42 3. 42 3. 42 3. 42 3. 42 3. 41 3. 42 3. 42 3. 42 3. 42 3. 43 3. 43 3. 44 3. 44 3. 45 3. 46 3. 47 3. 48 3. 48 3. 49 3. 50 3. 51 3. 51 3. 52 3. 52 3. 52 3. 53 3. 53 3. 52 3. 52 3. 51 3. 51 3. 51 3. 50 3. 49 3. 48 3. 47 3. 46 3. 45 3. 45 3. 44 3. 43 3. 43 3. 43 S 12 A ngle Mag -36. 35 -42. 93 -48. 73 -54. 29 -59. 82 -65. 28 -70. 67 -75. 97 -81. 24 -86. 45 88. 39 83. 29 78. 22 73. 16 68. 10 63. 07 58. 02 52. 99 47. 95 42. 91 37. 87 32. 78 27. 71 22. 64 17. 55 12. 44 7. 30 2. 14 -3. 01 -8. 15 -13. 28 -18. 47 -23. 66 -28. 79 -33. 90 -39. 00 -44. 12 -49. 28 -54. 36 -59. 39 -64. 39 -69. 39 -74. 39 -79. 32 -84. 20 -17. 05 86. 12 81. 37 0. 00 0. 00 0. 00 0. 00 0. 00 0. 00 0. 00 0. 00 0. 00 0. 00 0. 00 0. 00 0. 00 0. 00 0. 00 0. 00 0. 00 0. 00 0. 00 0. 00 0. 00 0. 01 0. 01 0. 01 0. 01 0. 01 0. 01 0. 01 0. 01 0. 01 0. 01 0. 01 0. 01 0. 01 0. 01 0. 01 0. 01 0. 01 0. 01 0. 01 0. 01 0. 01 0. 01 0. 01 0. 01 0. 01 0. 01 0. 01 S22 A ngle Mag -63. 41 -29. 52 72. 59 42. 47 27. 49 13. 11 4. 32 -3. 76 -11. 28 -17. 93 -24. 95 -30. 94 -40. 08 -45. 92 -50. 32 -56. 49 -63. 05 -67. 95 -74. 11 -79. 14 -83. 92 18. 48 84. 14 80. 03 73. 81 68. 78 64. 80 60. 68 55. 34 49. 63 47. 53 41. 87 38. 81 35. 08 30. 21 27. 00 21. 43 17. 73 16. 35 11. 43 8. 25 4. 95 2. 14 -1. 56 -5. 54 -10. 51 -14. 21 -19. 00 0. 02 0. 02 0. 01 0. 00 0. 01 0. 01 0. 01 0. 01 0. 01 0. 01 0. 01 0. 01 0. 01 0. 02 0. 02 0. 02 0. 03 0. 04 0. 04 0. 05 0. 06 0. 07 0. 08 0. 09 0. 10 0. 11 0. 12 0. 13 0. 14 0. 15 0. 16 0. 17 0. 18 0. 19 0. 20 0. 21 0. 22 0. 22 0. 23 0. 23 0. 24 0. 24 0. 24 0. 24 0. 24 0. 24 0. 24 0. 24 Angle -48. 45 -37. 80 -33. 00 27. 64 -38. 27 -44. 59 21. 28 15. 31 13. 40 13. 67 -16. 72 -6. 18 -65. 06 -53. 62 -44. 57 -39. 29 -37. 33 -37. 85 -39. 95 -42. 71 -45. 73 -49. 38 -53. 42 -57. 88 -62. 71 -67. 57 -72. 36 -77. 27 -82. 39 -51. 70 87. 01 81. 73 76. 45 71. 34 65. 86 60. 25 54. 28 48. 57 42. 85 36. 83 30. 81 24. 23 17. 61 10. 75 3. 94 -3. 27 -10. 81 -18. 81 5 Specifications subject to change without notice Filtronic Compound Semiconductors Ltd Fax: +44 (0) 1325 306177 Email: sales@filcs.com Tel: +44 (0) 1325 301111 Website: www.filtronic.com FMA3007 Production Datasheet v3.0 S-PARAMETERS CONTINUED S11 Frequenc y Mag 11. 12 11. 31 11. 5 11. 69 11. 88 12. 07 12. 26 12. 45 12. 64 12. 83 13. 02 13. 21 13. 4 13. 59 13. 78 13. 97 14. 16 14. 35 14. 54 14. 73 14. 92 15. 11 15. 3 15. 49 15. 68 15. 87 16. 06 16. 25 16. 44 16. 63 16. 82 17. 01 17. 2 17. 39 17. 58 17. 77 17. 96 18. 15 18. 34 18. 53 18. 72 18. 91 19. 1 19. 29 19. 48 19. 67 19. 86 20 S 21 Angle Mag 22. 84 19. 06 14. 69 9. 79 6. 23 1. 32 -2. 75 -7. 08 -11. 05 -15. 83 -20. 74 -26. 37 -33. 12 -39. 86 -46. 40 -54. 81 -64. 08 -72. 76 -47. 47 47. 91 71. 00 53. 20 33. 02 13. 93 -4. 28 -18. 94 -30. 60 -41. 49 -51. 22 -59. 08 -68. 00 -76. 62 -83. 90 17. 35 82. 44 76. 96 70. 63 62. 97 54. 75 45. 09 34. 89 25. 38 14. 08 -0. 07 -17. 44 -45. 86 -13. 12 61. 43 S 12 A ngle Mag 76. 53 71. 78 67. 04 62. 28 57. 43 52. 51 47. 60 42. 70 37. 72 32. 50 27. 22 21. 86 16. 46 11. 01 5. 41 -0. 34 -6. 03 -11. 60 -17. 22 -22. 91 -28. 64 -34. 30 -39. 83 -45. 39 -51. 01 -56. 69 -62. 28 -67. 91 -73. 44 -79. 17 -84. 87 -18. 55 83. 72 77. 99 72. 22 66. 41 60. 59 54. 74 48. 84 42. 97 37. 06 31. 13 25. 16 19. 10 13. 14 6. 99 0. 89 -5. 39 S22 A ngle Mag -22. 37 -27. 33 -31. 55 -37. 22 -42. 25 -48. 26 -52. 88 -57. 45 -64. 77 -71. 06 -76. 93 -82. 74 -16. 85 85. 12 79. 01 73. 33 68. 29 62. 69 57. 29 51. 71 46. 06 40. 76 34. 90 29. 64 24. 41 19. 88 14. 12 8. 67 3. 54 -3. 05 -7. 81 -13. 42 -18. 83 -24. 46 -29. 63 -35. 63 -40. 03 -46. 04 -51. 04 -56. 89 -61. 73 -67. 11 -72. 52 -78. 57 -84. 34 -17. 99 84. 17 78. 45 0. 11 0. 11 0. 11 0. 11 0. 11 0. 11 0. 10 0. 10 0. 10 0. 10 0. 09 0. 09 0. 08 0. 08 0. 07 0. 07 0. 06 0. 05 0. 05 0. 04 0. 04 0. 03 0. 03 0. 04 0. 04 0. 04 0. 05 0. 05 0. 06 0. 06 0. 07 0. 07 0. 07 0. 07 0. 07 0. 07 0. 07 0. 07 0. 07 0. 06 0. 06 0. 05 0. 04 0. 04 0. 03 0. 02 0. 02 0. 03 3. 43 3. 43 3. 44 3. 45 3. 47 3. 49 3. 52 3. 54 3. 58 3. 62 3. 65 3. 68 3. 72 3. 75 3. 78 3. 80 3. 81 3. 82 3. 84 3. 85 3. 85 3. 84 3. 84 3. 85 3. 85 3. 85 3. 85 3. 85 3. 86 3. 87 3. 87 3. 87 3. 87 3. 87 3. 88 3. 89 3. 89 3. 89 3. 89 3. 90 3. 90 3. 90 3. 91 3. 91 3. 92 3. 93 3. 95 3. 96 0. 01 0. 01 0. 01 0. 01 0. 01 0. 01 0. 02 0. 02 0. 02 0. 02 0. 02 0. 02 0. 02 0. 02 0. 02 0. 02 0. 02 0. 02 0. 02 0. 02 0. 02 0. 02 0. 02 0. 02 0. 02 0. 02 0. 02 0. 03 0. 03 0. 03 0. 03 0. 03 0. 03 0. 03 0. 03 0. 03 0. 03 0. 03 0. 03 0. 03 0. 03 0. 03 0. 03 0. 03 0. 03 0. 03 0. 03 0. 03 0. 23 0. 22 0. 21 0. 21 0. 20 0. 19 0. 18 0. 17 0. 16 0. 16 0. 15 0. 15 0. 15 0. 15 0. 15 0. 15 0. 16 0. 16 0. 16 0. 17 0. 17 0. 16 0. 16 0. 16 0. 16 0. 16 0. 15 0. 15 0. 14 0. 14 0. 14 0. 14 0. 13 0. 13 0. 13 0. 13 0. 13 0. 13 0. 13 0. 12 0. 12 0. 12 0. 12 0. 12 0. 12 0. 11 0. 10 0. 10 Angle -27. 22 -36. 26 -45. 16 -55. 08 -65. 94 -77. 17 -17. 48 77. 51 63. 15 48. 80 33. 57 17. 88 1. 73 -13. 77 -28. 48 -41. 98 -54. 27 -65. 54 -76. 15 -50. 08 48. 74 76. 52 69. 26 62. 48 56. 54 50. 74 45. 36 41. 50 37. 88 35. 17 31. 98 28. 68 25. 14 22. 71 20. 43 18. 02 15. 16 11. 60 7. 77 4. 20 1. 11 -3. 30 -7. 78 -12. 88 -19. 22 -24. 90 -30. 45 -37. 05 6 Specifications subject to change without notice Filtronic Compound Semiconductors Ltd Fax: +44 (0) 1325 306177 Email: sales@filcs.com Tel: +44 (0) 1325 301111 Website: www.filtronic.com FMA3007 Production Datasheet v3.0 BIASING CIRCUIT SCHEMATIC: VDD VG2 100nF 100pF 100pF 100nF RF Output RF Input VG1 100nF 100pF ASSEMBLY DIAGRAM: It is recommended that the RF connections be made using two bond wires 25µm in diameter and a maximum length of 300µm. Improved input return loss can be achieved, to compensate for bond wire length, with the addition of a microstrip transformer, shown in the diagram below. To Evaluation Board via an 0402 Surface Mounted capacitor 100pF Capacitor 0.8mm 0.61mm 0.8mm 0.61mm 1.0mm 1.0mm Substrate: Alumina Thickness: 635µm Transformer Impedance 43Ω Electrical Length 32º at 10GHz 100pF Capacitors To Evaluation Board via an 0402 Surface Mounted capacitor BILL OF MATERIALS: COMPONENT All RF tracks should be 50Ω characteristic material Capacitor, 100pF, chip capacitor Capacitor, 100pF, 0402 7 Specifications subject to change without notice Filtronic Compound Semiconductors Ltd Fax: +44 (0) 1325 306177 Email: sales@filcs.com Tel: +44 (0) 1325 301111 Website: www.filtronic.com FMA3007 Production Datasheet v3.0 PREFERRED ASSEMBLY INSTRUCTIONS: GaAs devices are fragile and should be handled with great care. Specially designed collets should be used where possible. The recommended die attach is gold/tin eutectic solder under a nitrogen atmosphere. Stage temperature should be 280-290°C; maximum time at temperature is one minute. The recommended wire bond method is thermo-compression wedge bonding with 0.7 or 1.0 mil (0.018 or 0.025 mm) gold wire. Stage temperature should be 250-260°C. Bonds should be made from the die first and then to the mounting substrate or package. The physical length of the bondwires should be minimised especially when making RF or ground connections. ORDERING INFORMATION: PART NUMBER FMA3007 (Gel-pak available on request) DESCRIPTION Die in Waffle-pack HANDLING PRECAUTIONS: To avoid damage to the devices care should be exercised during handling. Proper Electrostatic Discharge (ESD) precautions should be observed at all stages of storage, handling, assembly, and testing. These devices should be treated as Class 0 (0-250 V) as defined in JEDEC Standard No. 22-A114. Further information on ESD control measures can be found in MIL-STD-1686 and MILHDBK-263. APPLICATION NOTES & DESIGN DATA: Application Notes and design data including Sparameters, noise data are available on request. DISCLAIMERS: This product is not designed for use in any space based or life sustaining/supporting equipment. 8 Specifications subject to change without notice Filtronic Compound Semiconductors Ltd Fax: +44 (0) 1325 306177 Email: sales@filcs.com Tel: +44 (0) 1325 301111 Website: www.filtronic.com