Finisar
Product Specification OC-48 IR-1/STM S-16.1 Multirate 2x10 SFF Transceiver FTLF1421S1xCL
PRODUCT FEATURES • • • • • • • • • • Up to 2.67Gb/s bi-directional data links Standard 2x10 pin SFF footprint (MSA compliant) Analog diagnostics functions Uncooled 1310nm DFB laser transmitter Duplex LC connector Very low jitter Metal enclosure, for lower EMI Single 3.3V power supply Low power dissipation 2db data rates. Please refer to the Optical Specifications in Table IV to calculate a more accurate link budget based on specific conditions in your application.
VI.
Environmental Specifications
Finisar 1310nm SFP transceivers have an extended operating temperature range from –10°C to +70°C case temperature.
Parameter Case Operating Temperature Storage Temperature Symbol Top Tsto Min -10 -40 Typ Max 70 85 Units °C °C Ref.
VII.
Regulatory Compliance
Finisar transceivers are Class 1 Laser Products and comply with US FDA regulations. These products are certified by TÜV and CSA to meet the Class 1 eye safety requirements of EN (IEC) 60825 and the electrical safety requirements of EN (IEC) 60950. Copies of certificates are available at Finisar Corporation upon request.
© Finisar Corporation March, 2006 Rev A
Page 5
FTLF1421S1XCL 2x10 Pin SFF Product Specification – March 2006
Finisar
VIII. Analog Diagnostics Functions (Top = -10 to 70 °C, VCC = 3.00 to 3.60 Volts)
Parameter Transmitter Monitor photodiode current monitor Laser bias current monitor Receiver Received photocurrent Photodiode responsivity Applied voltage at PD pin Symbol Pmon+, PmonBmon+, BmonRpd R Vpd Min 0 0 Typ Max Vcc Vcc Unit V V Ref. 1 2
0 0.5 2.4
0.9
1 1.0 Vcc
mA A/W V
3 3
Notes: 1. Pins 19 and 20 provide an analog voltage output proportional to the monitor photodiode current, per the following formula: IBIAS = .V(Pmon+ - Pmon-) / 200Ω. The figure below shows the equivalent circuit. 2. Pins 17 and 18 provide an analog voltage output proportional to the laser bias current, per the following formula: IBIAS = .V(Bmon+ - Bmon-) / 10Ω. The figure below shows the equivalent circuit. 3. Pin 1 is used to monitor the received photocurrent. It must be connected to a positive voltage within the range specified above. The current that flows into this pin is the received photocurrent. The received power is given by the photocurrent multiplied by the photodiode responsivity.
Vcc Laser 3 KΩ Bmon+ 10 Ω Bmon3 KΩ Ibias Imon 200 Ω Pmon3 KΩ Receiver Photodidoe Vcc Monitor Photodidoe 3 KΩ Pmon+ Ipd Vpd
Analog monitoring function connections.
© Finisar Corporation March, 2006 Rev A
Page 6
FTLF1421S1XCL 2x10 Pin SFF Product Specification – March 2006
Finisar
IX.
Mechanical Specifications
Finisar’s OC-48/STM-16 Small Form Factor (SFF) transceivers comply with the standard dimensions defined by the Small Form Factor Multi-Sourcing Agreement (MSA).
FTLF1421S1GCL (dimensions are in inches) – 2 pin version
© Finisar Corporation March, 2006 Rev A
Page 7
FTLF1421S1XCL 2x10 Pin SFF Product Specification – March 2006
Finisar
FTLF1421S1HCL (dimensions are in inches) – 6 pin version
© Finisar Corporation March, 2006 Rev A
Page 8
FTLF1421S1XCL 2x10 Pin SFF Product Specification – March 2006
Finisar
FTLF1421S1HCL – 6 pin version (Long EMI Shield)
© Finisar Corporation March, 2006 Rev A
Page 9
FTLF1421S1XCL 2x10 Pin SFF Product Specification – March 2006
Finisar
X.
PCB Layout and Bezel Recommendations
Minimum Recommended Pitch is 0.600”
© Finisar Corporation March, 2006 Rev A
Page 10
FTLF1421S1XCL 2x10 Pin SFF Product Specification – March 2006
Finisar
XI. 1.
References Small Form Factor (SFF) Transceiver Multi-Source Agreement (MSA). January 1998. Documentation is available from Finisar upon request. Bellcore GR-253 and ITU-T G.957 Specifications (Transmitter Optical Output Power complies with SONET OC-48 requirements only). IEEE Std 802.3, 2002 Edition, Clause 38, PMD Type 1000BASE-LX. IEEE Standards Department, 2002. (Transmit Optical Output has a minimum Extinction Ratio of 8.2 dB only). “Fibre Channel Draft Physical Interface Specification (FC-PI 13.0)”. American National Standard for Information Systems. (*) Directive 2002/95/EC of the European Council Parliament and of the Council. “On the restriction of the use of certain hazardous substances in electrical and electronic equipment”. January 27, 2003. “Application Note AN-2038: Finisar Implementation of RoHS Compliant Transceivers:. Finisar Corporation, January 21, 2005.
2.
3.
4.
5.
6.
(*) Neither IEEE 802.3 nor FC-PI 13.0 specifies a 1310nm DFB single mode interface. The FTLF1421S1XCL complies with these standards except for receiver sensitivity, and transmit output power. See Section IV for details.
XII.
For More Information
Finisar Corporation 1308 Moffett Park Drive Sunnyvale, CA 94089-1133 Tel. 1-408-548-1000 Fax 1-408-541-6138 sales@finisar.com www.finisar.com
© Finisar Corporation March, 2006 Rev A
Page 11
FTLF1421S1XCL 2x10 Pin SFF Product Specification – March 2006
Finisar
© Finisar Corporation March, 2006 Rev A
Page 12
很抱歉,暂时无法提供与“FTLF1421S1GCL”相匹配的价格&库存,您可以联系我们找货
免费人工找货