FTR-1629-59

Finisar Preliminary Product Specification DWDM GBIC Transceiver FTR-1629-XX PRODUCT FEATURES • • • • • • • • • Up to 1.25 Gb/s bi-directional data links Standard GBIC footprint Temperature-stabilized DWDMrated DFB laser transmitter 100GHz ITU Grid, C Band Very low jitter Metal enclosure for low EMI Extended operating range: 0°C to 70°C case temperature Wavelength controlled within ± 0.1 nm over entire temperature range Extended link budget of 30dB with APD receiver technology APPLICATIONS • • • ITU grid optical networks Bandwidth aggregation Ring topologies with OADM Finisar’s Dense Wavelength-Division Multiplexing (DWDM) transceivers offer DWDM transport with dramatically lower power and cost in a standard plugable GBIC package. The FTR-1629 is designed expressly for service providers deploying DWDM networking equipment in metropolitan access and core networks. The fiber link budget has been enhanced to 30dB with an Avalanche Photo Diode (APD) receiver. The FTR-1629 has serial identification features as described for Module Definition “4” GBICs in the GBIC Specification Revision 5.51 . In addition, digital diagnostic features are implemented as described in Finisar Application Note AN-2030, “Using the Finisar GBIC I2 C Test/Diagnostics Port”2 . © Finisar Corporation Rev D, June 2003 PRELIMINARY and Confidential Page 1 Finisar PRODUCT SELECTION Product Code FTR-1629-17 FTR-1629-18 FTR-1629-19 FTR-1629-20 FTR-1629-21 FTR-1629-22 FTR-1629-23 FTR-1629-24 FTR-1629-25 FTR-1629-26 FTR-1629-27 FTR-1629-28 FTR-1629-29 FTR-1629-30 FTR-1629-31 FTR-1629-32 FTR-1629-33 FTR-1629-34 FTR-1629-35 FTR-1629-36 FTR-1629-37 FTR-1629-38 FTR-1629-39 FTR-1629-40 FTR-1629-41 FTR-1629-42 FTR-1629-43 FTR-1629-44 FTR-1629-45 FTR-1629-46 FTR-1629-47 FTR-1629-48 FTR-1629-49 FTR-1629-50 FTR-1629-51 FTR-1629-52 FTR-1629-53 FTR-1629-54 FTR-1629-55 FTR-1629-56 FTR-1629-57 FTR-1629-58 FTR-1629-59 FTR-1629-60 FTR-1629-61 Frequency (THz) 191.7 191.8 191.9 192.0 192.1 192.2 192.3 192.4 192.5 192.6 192.7 192.8 192.9 193.0 193.1 193.2 193.3 193.4 193.5 193.6 193.7 193.8 193.9 194.0 194.1 194.2 194.3 194.4 194.5 194.6 194.7 194.8 194.9 195.0 195.1 195.2 195.3 195.4 195.5 195.6 195.7 195.8 195.9 196.0 196.1 Center Wavelength (nm) 1563.86 1563.05 1562.23 1561.42 1560.61 1559.79 1558.98 1558.17 1557.36 1556.55 1555.75 1554.94 1554.13 1553.33 1552.52 1551.72 1550.92 1550.12 1549.32 1548.51 1547.72 1546.92 1546.12 1545.32 1544.53 1543.73 1542.94 1542.14 1541.35 1540.56 1539.77 1538.98 1538.19 1537.40 1536.61 1535.82 1535.04 1534.25 1533.47 1532.68 1531.90 1531.12 1530.33 1529.55 1528.77 © Finisar Corporation Rev D, June 2003 PRELIMINARY and Confidential Page 2 FTR-1629-XX DWDM GBIC Preliminary Product Specification – June 2003 Finisar I. Pin Out Pin Name RX_LOS GND GND MOD_DEF(0) MOD_DEF(1) MOD_DEF(2) TX_DISABLE GND GND TX_FAULT GND -RX_DAT +RX_DAT GND VCC VCC GND +TX_DAT -TX_DAT GND Pin # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Sequence 2 2 2 2 2 2 2 2 2 2 1 1 1 1 2 2 1 1 1 1 Table 1. GBIC to Host Connector Pin Assignment “Sequence” indicates the order in which pins make contact when the device is hot plugged. See “Table 3: Signal Definitions” in the GBIC Specification Revision 5.51 for a description of the function of each pin listed above. © Finisar Corporation Rev D, June 2003 PRELIMINARY and Confidential Page 3 FTR-1629-XX DWDM GBIC Preliminary Product Specification – June 2003 Finisar II. Electrical Power Interface The GBIC specification calls for a range of 4.75V to 5.25 volts as described in Table 2. The maximum voltage of 6V is not to be applied continuously. Parameter Supply Current Inrush Current Maximum Voltage Input Voltage Symbol Is Isurge Vmax Vcc 4.75 5.0 Min Typ 250 Max 400 350 30 6 5.25 Units mA mA mA V V Referenced to GND Notes/Conditions Tc