FTRJ1519P1WNL

Product Specification 2 Gigabit Long-Wavelength Pluggable SFP Transceiver FTRJ1519P1xNL PRODUCT FEATURES • • • • • • • • • • • Up to 2.125Gb/s bi-directional data links Hot-pluggable SFP footprint Built-in digital diagnostic functions Uncooled 1550nm DFB laser transmitter Duplex LC connector Very low jitter Metal enclosure, for lower EMI Single 3.3V power supply Up to 80 km on 9/125µm SMF Low power dissipation typically 2.0V or open, enabled on TDIS 2Gb/s data rates. Please refer to the Optical Specifications in Table IV to calculate a more accurate link budget based on specific conditions in your application. VI. Environmental Specifications Finisar 1550nm SFP transceivers have an extended operating temperature range from –5°C to +85°C case temperature. Parameter Case Operating Temperature Storage Temperature Symbol Top Tsto Min -5 -40 Typ Max 85 85 Units °C °C Ref. VII. Regulatory Compliance Finisar transceivers are Class 1 Laser Products and comply with US FDA regulations. These products are certified by TÜV and CSA to meet the Class 1 eye safety requirements of EN (IEC) 60825 and the electrical safety requirements of EN (IEC) 60950. Copies of certificates are available at Finisar Corporation upon request. Copies of the referenced certificates are available at Finisar Corporation upon request.  Finisar Corporation April 11, 2005 Rev C Page 5 FTRJ1519P1xCL Pluggable SFP Product Specification – April 2005 VIII. Digital Diagnostic Functions Finisar FTRJ1519P1xNL SFP transceivers support the 2-wire serial communication protocol as defined in the SFP MSA1. It is very closely related to the E2PROM defined in the GBIC standard, with the same electrical specifications. The standard SFP serial ID provides access to identification information that describes the transceiver’s capabilities, standard interfaces, manufacturer, and other information. Additionally, Finisar SFP transceivers provide a unique enhanced digital diagnostic monitoring interface, which allows real-time access to device operating parameters such as transceiver temperature, laser bias current, transmitted optical power, received optical power and transceiver supply voltage. It also defines a sophisticated system of alarm and warning flags, which alerts end-users when particular operating parameters are outside of a factory set normal range. The SFP MSA defines a 256-byte memory map in E2PROM that is accessible over a 2-wire serial interface at the 8 bit address 1010000X (A0h). The digital diagnostic monitoring interface makes use of the 8 bit address 1010001X (A2h), so the originally defined serial ID memory map remains unchanged. The interface is identical to, and is thus fully backward compatible with both the GBIC Specification and the SFP Multi Source Agreement. The complete interface is described in Finisar Application Note AN2030: “Digital Diagnostics Monitoring Interface for SFP Optical Transceivers”. The operating and diagnostics information is monitored and reported by a Digital Diagnostics Transceiver Controller (DDTC) inside the transceiver, which is accessed through a 2-wire serial interface. When the serial protocol is activated, the serial clock signal (SCL, Mod Def 1) is generated by the host. The positive edge clocks data into the SFP transceiver into those segments of the E2PROM that are not write-protected. The negative edge clocks data from the SFP transceiver. The serial data signal (SDA, Mod Def 2) is bi-directional for serial data transfer. The host uses SDA in conjunction with SCL to mark the start and end of serial protocol activation. The memories are organized as a series of 8-bit data words that can be addressed individually or sequentially. For more information, please see the SFP MSA documentation1 or Finisar Application Note AN-2030. Digital diagnostics for the FTRJ1519P1xNL are externally calibrated by default. Please note that evaluation board FDB-1018 is available with Finisar ModDEMO software that allows simple to use communication over the 2-wire serial interface.  Finisar Corporation April 11, 2005 Rev C Page 6 FTRJ1519P1xCL Pluggable SFP Product Specification – April 2005 IX. Mechanical Specifications Finisar’s OC-48/STM-16 Small Form Factor Pluggable (SFP) transceivers are compatible with the dimensions defined by the SFP Multi-Sourcing Agreement (MSA). FTRJ1519P1BNL  Finisar Corporation April 11, 2005 Rev C Page 7 FTRJ1519P1xCL Pluggable SFP Product Specification – April 2005 FTRJ1519P1WNL  Finisar Corporation April 11, 2005 Rev C Page 8 FTRJ1519P1xCL Pluggable SFP Product Specification – April 2005 X. PCB Layout and Bezel Recommendations  Finisar Corporation April 11, 2005 Rev C Page 9 FTRJ1519P1xCL Pluggable SFP Product Specification – April 2005  Finisar Corporation April 11, 2005 Rev C Page 10 FTRJ1519P1xCL Pluggable SFP Product Specification – April 2005 XI. 1. 2. 3. 4. References “Fibre Channel Physical and Signaling Interface (FC-PH, FC-PH2, FC-PH3)”. American National Standard for Information Systems. “Fibre Channel Draft Physical Interface Specification (FC-PI 13.0)”. American National Standard for Information Systems.(*) Small Form Factor Pluggable (SFP) Transceiver Multi-Source Agreement (MSA), September 2000. Documentation is currently available at Finisar upon request. IEEE Std 802.3. IEEE Standards Department, 2002. (*) Neither IEEE 802.3 nor FC-PI 13.0 specifies a 1550nm DFB single mode interface. The FTRJ1519P1xNL complies with these standards except for receiver sensitivity, and transmit output power. See Section IV for details. XII. For More Information Finisar Corporation 1308 Moffett Park Drive Sunnyvale, CA 94089-1133 Tel. 1-408-548-1000 Fax 1-408-541-6138 sales@finisar.com www.finisar.com  Finisar Corporation April 11, 2005 Rev C Page 11