V23838-S5-N1

Product Specification Press-fit Cage for Small Form-factor Pluggable (SFP) Transceiver V23838-S5-N1 V23838-S5-N1-BB PRODUCT FEATURES V23838-S5-N1 • 3D foot design for improved press-fit retention and contact to host board holes • One-piece, stainless steel construction • Low emission design via fold-back spring fingers – no openings for radiation to pass through • Enhanced transceiver kick-out springs • Simple and fast installation/removal • Host board holes not damaged when cage is removed • Heat transfer windows on all SFP cage surfaces • Supports MSA compliant host board layouts and transceiver designs File: 1142 V23838-S5-N1-BB File: 1143 PRODUCT SELECTION Part Number Description V23838-S5-N1 For single-sided mounting V23838-S5-N1-BB For double-sided "belly to belly" mounting (see Figure 3) © Finisar Corporation August 07, 2003 Rev. D Page 1 V23838-S5-N1, V23838-S5-N1-BB Product Specification – August 2003 Description Finisar is offering its cage for Small Form-factor Pluggable (SFP) transceivers with one of the most rigid mechanical designs available on the market. The cage is designed for press fit applications in order to reduce high volume manufacturing effort. Externally bent bezel contact springs and one-piece construction enhance EMI performance. Application Notes • Testing of rear connector may take place before SFP Cage is installed onto host board • SFP cage mounting holes should be plated with HASL, gold, or immersion silver finish per MSA dimensional recommendations • For double-sided mounting, host board thickness is .118 in [3.0 mm] minimum per the MSA. For belly-to-belly applications, three mounting feet are removed to avoid interference (V23838-S5-N1-BB) • Supports any single sided, belly to belly, or offset belly to belly configuration with a minimum pitch of 16.25 mm • Installation of the SFP cage should be done with a solid metal block across the top surface of the cage. Block dimensions to be controlled by customer • Removal of the cage should be done with an internal solid metal block • The Finisar SFP cage does not cause any damage when carefully removed; the outside profile of the 3D feet is smooth and will not destroy pre-plated host board mounting holes • Trapped fluids from washing process must be dried to prevent corrosion beneath the SFP cage • Cage retention depends on finished hole size and plating thickness © Finisar Corporation August 07, 2003 Rev. D Page 2 V23838-S5-N1, V23838-S5-N1-BB Product Specification – August 2003 X SFP Cage Host Board Mechanical Layout 1) 1) Datum and basic dimensions established by customer 2) Pads and vias are chassis ground, 11 places 3) Thru holes, plating optional 34.5 10 3 PLACES Y 1) 7.2 2.5 BSC 2.5 4.8 11.93 8.48 1.7 1.7 9.6 5.68 8.58 PIN 1 2) 2 11 PLACES 11.08 14.25 16.25 3.68 CROSS-HATCHED AREA DENOTES COMPONENT AND TRACE KEEP-OUT (EXCEPT CHASSIS GROUND) ∅0.85±0.05 ⊕ ∅0.1 S X Y A 2) 7.1 2) 2 11 PLACES THIS AREA DENOTES COMPONENT KEEP-OUT (TRACES ALLOWED) ∅1.05±0.1 ⊕ ∅0.1 L X A S 10 HOLES 2) ∅0.95±0.05 ⊕ ∅0.1 L X A S 9 HOLES 3) 5 10 3 PLACES 26.8 41.3 42.3 Dimensions in mm Figure 1 File: 1519 Single-sided Host Board Layout 16.25±0.1 [.640] 1) 1.7±0.9 3.5±0.3 10.4±0.1 10 REF Y 15.25±0.1 [.600] Y SECTION Y-Y 0.4±0.1 BEZEL OPENING BELOW PC BOARD 1) MINIMUM PITCH ILLUSTRATED, ENGLISH DIMENSIONS ARE FOR REFERENCE ONLY NOT RECOMMENDED FOR PCI EXPANSION CARD APPLICATIONS Dimensions in mm [inches] Figure 2 File: 1520 Recommended Bezel Design © Finisar Corporation August 07, 2003 Rev. D Page 3 V23838-S5-N1, V23838-S5-N1-BB Product Specification – August 2003 V23838-S5-N1 SINGLE SIDED MOUNTING HOST PCB CROSS SECTION V23838-S5-N1-BB BELLY TO BELLY THREE FEET REMOVED File: 1514 Figure 3 © Finisar Corporation August 07, 2003 Rev. D Page 4 V23838-S5-N1, V23838-S5-N1-BB Product Specification – August 2003 Single-sided Application File: 1515 Figure 4 File: 1516 Figure 5 © Finisar Corporation August 07, 2003 Rev. D Page 5 V23838-S5-N1, V23838-S5-N1-BB Product Specification – August 2003 Belly to Belly Application File: 1517 Figure 6 File: 1518 Figure 7 © Finisar Corporation August 07, 2003 Rev. D Page 6 V23838-S5-N1, V23838-S5-N1-BB Product Specification – August 2003 Package Outlines 16.25 48.70 14 9 9.55 11.50 2.10 A DETAIL A Dimensions in mm Figure 8 File: 1221 V23838-S5-N1 © Finisar Corporation August 07, 2003 Rev. D Page 7 V23838-S5-N1, V23838-S5-N1-BB Product Specification – August 2003 16.25 48.70 14 9 11.50 9.55 2.10 A DETAIL A Dimensions in mm Figure 9 File: 1222 V23838-S5-N1-BB © Finisar Corporation August 07, 2003 Rev. D Page 8 V23838-S5-N1, V23838-S5-N1-BB Product Specification – August 2003 Revision History: Previous Version: Page August 07, 2003 Rev. D July 08, 2003 Subjects (major changes since last revision) Company name has been changed Document’s layout has been changed December 2004 For More Information Finisar Corporation 1308 Moffett Park Drive Sunnyvale, CA 94089-1133 Tel. 1-408-548-1000 Fax 1-408-541-6138 sales@finisar.com www.finisar.com © Finisar Corporation August 07, 2003 Rev. D Page 9