FSP1084D25A

5A LOW DROPOUT LINEAR REGULATOR FSP1084 FEATURES Low Dropout Voltage: 1.3V Typically at 5A Current Limiting and Thermal Protection Output Current: 5A Current Limit: 6.5A Operating Junction Temperature Range: 0 to 125℃ Line Regulation: 0.015%(Typical) Load Regulation: 0.2%(Typical) GENERAL DESCRIPTION The FSP1084 is a series of low dropout positive voltage regulators with a maximum dropout of 1.5V at 5A of load current. The series features on-chip thermal limiting which provides protection against any combination of overload and ambient temperatures that would create excessive junction temperatures. It also includes a trimmed bandgap reference and a current limiting circuit. The FSP1084 is available in 1.5V, 1.8V, 2.5V, 3.3V and 5.0V versions. The fixed versions integrate the adjust resistors. It is also available in an adjustable version which can set output voltage with two external resistors. The FSP1084 series is available in standard package of TO263-2L, TO220-3L and TO252-2L. APPLICATIONS High Efficiency Linear Regulators Battery Chargers Post Regulation for Switching Supply Microprocessor Supply Desktop PCs, RISC and Embedded Processors’ Supply PIN CONFIGURATION (1) TO220-3L 3 2 1 Metal Tab VOUT VIN VOUT ADJ/GND (2) TO252-2L 3 2 1 Metal Tab VOUT VOUT ADJ/GND VIN (3) TO263-2L 3 2 1 Metal Tab VOUT VIN VOUT (TAB) ADJ/GND BLOCK DIAGRAM 3 INPUT A1 B A2 For Adjustable Output, disconnect A1 and A2, connect B For Fixed Output,connect A1 and A2, disconnect B 1 ADJ/GND 1/9 + Thermal Protection 2 OUTPUT 2007-4-6 5A LOW DROPOUT LINEAR REGULATOR FSP1084 ABSOLUTE MAXIMUM RATINGS (NOTE 1) Symbol Parameter Rating Unit TJ Maximum Junction Temperature 150 ℃ TS Storage Temperature Range -65~150 ℃ TLEAD Lead Temperature (10 sec.) 300 ℃ ESD ESD (Human Body Model) 2000 V Note 1: Stresses greater than those listed under“Absolute Maximum Ratings” may cause permanent damage to the device. These are stress rating only, and functional operation of the device at these or any other conditions beyond those indicated under “Recommended Operating Conditions” is not implied. Exposure to “Absolute Maximum Ratings” for extended periods may affect device reliability. RECOMMENDED OPERATING CONDITIONS Symbol VIN TJ Parameter Input Voltage Operating Junction Temperature Range Rating 12 0~125 Unit V ℃ ELECTRICAL CHARACTERISTICS Typicals and limits appearing in normal type apply for TJ=25℃. Limiting appearing in Boldface type apply over the entire operating junction temperature range. Parameter Reference Voltage Symbol VREF FSP1084-ADJ FSP1084-1.5 FSP1084-1.8 Output Voltage VOUT FSP1084-2.5 FSP1084-3.3 FSP1084-5.0 RegLINE FSP1084-ADJ FSP1084-1.5 FSP1084-1.8 Line Regulation ΔVOUT FSP1084-2.5 FSP1084-3.3 FSP1084-5.0 IO=10mA,4.1V≤VIN≤10V IO=10mA,4.9V≤VIN≤10V IO=10mA,6.6V≤VIN≤10V Test Condition IO=10mA, VIN-VOUT=3V IO=10mA~5A,1.5V≤VIN-VOUT≤5V IO=0mA, VIN=4.5V IO=10mA~5A, 3.1V≤VIN≤6V IO=0mA, VIN=4.8V IO=10mA~5A, 3.4V≤VIN≤6V IO=0mA, VIN=5.5V IO=10mA~5A, 4.1V≤VIN≤7V IO=0mA, VIN=6.3V IO=10mA~5A, 4.9V≤VIN≤8V IO=0mA, VIN=8V IO=10mA~5A, 6.6V≤VIN≤10V IO=10mA,2.85V≤VIN≤10V IO=10mA,3.1V≤VIN≤10V IO=10mA,3.4V≤VIN≤10V Min. 1.238 1.225 1.485 1.470 1.782 1.764 2.475 2.450 3.267 3.234 4.950 4.900 Typ. 1.250 1.250 1.5 1.5 1.8 1.8 2.5 2.5 3.3 3.3 5.0 5.0 0.015 0.035 0.5 1 0.5 1 0.5 1 0.5 1 0.5 1 Max. 1.262 1.270 1.515 1.530 1.818 1.836 2.525 2.550 3.333 3.366 5.050 5.100 0.2 0.2 6 6 6 6 6 6 6 6 10 10 Unit V V V V V V % mV mV 2/9 2007-4-6 5A LOW DROPOUT LINEAR REGULATOR FSP1084 ELECTRICAL CHARACTERISTICS (CONTINUED) Typicals and limits appearing in normal type apply for TJ=25℃. Limiting appearing in Boldface type apply over the entire operating junction temperature range. Parameter Symbol RegLoad Load Regulation ΔVOUT Dropout Voltage Current Limit Adjust Pin Current Adjust Pin Current Change Minimum Load Current Quiescent Current Ripple Rejection Temperature Stability Long-term Stability RMS Noise (% of VOUT) Thermal Resistance, Junction to case FSP1084-ADJ FSP1084-1.5/ 1.8/2.5/3.3 FSP1084-5.0 ILIMIT Test Condition IO=0mA~5A, VIN-VOUT=3V IO=0mA~5A, VIN-VOUT=3V IO=0mA~5A, VIN-VOUT=3V 5.5 Min. Typ. 0.1 0.2 3 7 5 10 1.3 6.5 55 0.2 3 5 60 72 0.5 0.5 0.003 4 3 3 Max. 0.3 0.4 15 20 20 35 1.5 120 5 10 10 Unit % mV mV V A µA µA mA mA dB % % % ℃/W IO=5A, ΔVREF,ΔVOUT=1% VIN-VOUT=3V IO=10mA, VIN=4.25V IO=10mA~5A, 1.5V≤VIN-VOUT≤4.5V VIN=10V (FSP1084-ADJ) VIN=10V (FSP1084) f=120Hz,COUT=25uF Tantalum, VIN-VOUT=3V, IOUT=5A IO=10mA, VIN-VOUT=1.5V TA=125℃, 1000hrs 10Hz≤f≤10kHz θJC TO252-2L TO220-3L TO263-2L TYPICAL APPLICATIONS FSP1084-ADJ Vin 10µF Tantalum + Vin ADJ Vout R1 + Vout 22µF Tantalum R2 V out=Vref*(1+R2/R1)+Iadj*R2 Vin 10µF Tantalum + FSP1084-5.0 Vin GND Vout + Vout 22µF Tantalum 3/9 2007-4-6 5A LOW DROPOUT LINEAR REGULATOR FSP1084 TYPICAL PERFORMANCE CHARACTERISTICS Dropout Voltage vs Output Current 1.50 1.45 1.40 1.35 1.30 1.25 1.20 1.15 1.10 1.05 1.00 0.95 0.90 0.85 0.80 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 Output Current (A) 2.53 2.52 Output Voltage (V) 2.51 2.50 2.49 2.48 2.47 0 Output Voltage vs Temperature Dropout Voltage (V) 25 50 75 TJ (℃) 100 125 0.0 Line Regulation (mV) -0.2 -0.4 -0.6 -0.8 -0.1 0 Line Regulation vs Temperature Adjust Pin Current (µA) 25 50 75 TJ (℃) 100 125 80 75 70 65 60 55 50 45 40 35 30 25 20 Adjust Pin Current vs Output Current 0 1 2 3 4 Output Current (A) 5 4/9 2007-4-6 5A LOW DROPOUT LINEAR REGULATOR FSP1084 TYPICAL PERFORMANCE CHARACTERISTICS (CONTINUED) Dropout Voltage vs Temperature Short Circuit Current (A) 1.40 Dropout Voltage (V) 1.35 1.30 1.25 1.20 0 8 7 6 5 4 3 2 1 0 Short Circuit Current vs Dropout Voltage 25 50 75 TJ (℃) 100 125 0 2 4 6 8 Dropout Voltage (V) 10 12 Load Transient Response Line Transient Response Vin=5.5V, Vout=2.5V Io=100mA to 5A Cin=Cout=10µ(tan) Vin=4.5V to 6.5V Vout=2.5V Io=200mA Cin=1µ(tan) Cout=10µ(tan) 5/9 2007-4-6 5A LOW DROPOUT LINEAR REGULATOR FSP1084 ORDERING INFORMATION FSP1084XXXX Package: T:TO220-3L K:TO263-2L D:TO252-2L Output Voltage: Blank: ADJ 15: 1.5V 18: 1.8V 25: 2.5V 33: 3.3V 50: 5.0V Temperature Grade: Packing: Blank: Tube or Bulk Blank:0~70℃ A: Tape & Reel MARKING INFORMATION (1)TO220-3L (2) TO263-2L Logo Logo 1084-VV YYWWXX Part Number: 1084-ADJ: ADJ 1084-15: 1.5V 1084-18: 1.8V 1084-25: 2.5V 1084-33: 3.3V 1084-50: 5.0V Internal Code Date Code: YY: Year (01=2001) WW: Nth week (01~52) 1084-VV YYWWXX Part Number: 1084-ADJ: ADJ 1084-15: 1.5V 1084-18: 1.8V 1084-25: 2.5V 1084-33: 3.3V 1084-50: 5.0V Internal Code Date Code: YY: Year (01=2001) WW: Nth week (01~52) (3) TO252-2L Logo 1084-VV YYWWXX Part Number: 1084-ADJ: ADJ 1084-15: 1.5V 1084-18: 1.8V 1084-25: 2.5V 1084-33: 3.3V 1084-50: 5.0V Internal Code Date Code: YY: Year (01=2001) WW: Nth week (01~52) 6/9 2007-4-6 5A LOW DROPOUT LINEAR REGULATOR FSP1084 PACKAGE INFORMATION (1) TO220-3L E P A F Q H1 SEATING PLANE D b1 L1 b L e e1 C J1 Symbol A b1 b C D E e e1 F H1 J1 L L1 P Q Min. 3.56 1.16 0.51 0.356 14.20 9.66 2.29 4.83 0.55 5.84 2.08 12.72 3.66 3.56 2.58 Dimensions In Millimeters Nom. 4.20 1.46 0.813 15.35 10.20 2.54 5.08 0.95 6.35 2.48 13.72 5.00 3.81 2.98 Max. 4.82 1.76 1.14 0.406 16.50 10.66 2.79 5.33 1.35 6.86 2.88 14.72 6.35 4.06 3.38 Min. 0.140 0.046 0.020 0.014 0.559 0.380 0.090 0.190 0.022 0.230 0.082 0.501 0.144 0.140 0.102 Dimensions In Inches Nom. 0.165 0.057 0.032 0.604 0.402 0.100 0.200 0.037 0.250 0.098 0.540 0.197 0.150 1.117 Max. 0.190 0.069 0.045 0.016 0.650 0.420 0.110 0.210 0.053 0.270 0.113 0.580 0.250 0.160 0.133 7/9 2007-4-6 5A LOW DROPOUT LINEAR REGULATOR FSP1084 (2) TO263-2L E 10.9 L2 D 9.1 L3 e b b2 1.3 2.54 Land Pattern Recommendation (Unit : mm) C 3 Symbol A b b2 C C2 D E e L L1 L2 L3 Dimensions In Millimeters Nom. Max. 4.45 4.83 0.75 0.99 1.27 1.40 0.38TYP. 1.14 1.27 1.40 8.65 9.15 9.65 9.65 9.97 10.29 2.54BSC. 14.61 15.24 15.88 2.28 2.54 2.80 1.30 2.92 1.27 1.52 1.78 Min. 4.06 0.51 1.14 Min. 0.160 0.020 0.045 0.045 0.341 0.380 0.575 0.090 0.050 Dimensions In Inches Nom. 0.175 0.030 0.050 0.015TYP. 0.050 0.360 0.393 0.100BSC. 0.600 0.100 0.051 0.060 C2 L1 A 15.7 L Max. 0.190 0.039 0.055 0.055 0.380 0.405 0.625 0.110 0.115 0.070 8/9 2007-4-6 5A LOW DROPOUT LINEAR REGULATOR FSP1084 (3) TO252-2L 5.6 E b2 L2 11.0 5.6 2.25 L1 2.0 1.2 b e1 H C1 L e Land Pattern Recommendation (Unit : mm) 7.2 D C A1 SEATING PLANE SEE NOTE2 Notes: 1. JEDEC Outline:TO-252 AB 2. Mils suggested for positive contact at mounting Symbol A A1 b b2 C C1 D E e e1 H L L1 L2 Dimensions In Millimeters Nom. Max. 2.29 2.38 1.15 1.32 0.78 5.35 5.43 0.51TYP. 0.52 0.58 5.57 5.80 6.58 6.68 2.34 4.68 9.70 10.40 0.83 1.78 0.95 2.03 Dimensions In Inches Nom. 0.090 0.045 0.211 0.020TYP. 0.020 0.219 0.259 0.382 0.033 0.070 Min. 2.18 1.08 0.64 5.23 0.46 5.33 6.38 2.24 4.48 9.00 0.51 0.65 1.52 Min. 0.086 0.043 0.025 0.206 0.018 0.210 0.251 0.088 0.176 0.354 0.020 0.026 0.060 9/9 2007-4-6 A Max. 0.094 0.052 0.031 0.214 0.023 0.228 0.263 0.092 0.184 0.409 0.037 0.080