FO3PSCDM156.253906-T3

3.2mm x 2.5mm LVPECL Oscillator FO3PS Features • • • • LVPECL Output Stabilities to ±20 PPM Temperature Ranges to -40˚C to +85˚C Supply Voltages: 2.5V, 3.3V ELECTRICAL CHARACTERISTICS PARAMETERS Frequency Range (FO) Temperature Range Storage (TSTG) Supply Voltage (VDD) (±5%) Input Current (IDD) Standby Current Output Symmetry (50% VP-P level) Rise Time (20%~80% VP-P level) Fall Time (80%~20% VP-P level) Output Voltage Level (VOL) (VOH) Output Load Start-up Time (TS) Output Disable Time1 Output Enable Time1 Aging (@ 25C) Phase Jitter (12kHz~20MHz) Maximum Soldering Temp / Time Moisture Sensitivity Level (MSL) Termination Finish Seal Method Lead (Pb) Free RoHS/REACH Compliant MAX (Unless otherwise noted) 13.5 ~ 250 MHz -55°C ~ +125°C 2.5V; 3.3V ±10% 70 mA 15µA 45% ~ 55% 0.5 nS 0.5 nS VDD – 1.62V VDD – 1.025V Min. 50 Ohms to VDD – 2.0V 10mS 200nS 10mS ±5PPM first year 1pS 260°C / 10 Seconds x 2 1 Au over Ni Seam Seal YES YES ENABLE / DISABLE FUNCTION Pin1 OPEN 1 ‘1’ Level VIH ≥ 80%VDD ‘0’ Level VIL ≤ 20%VDD Revised A: 08/29/2019 Out 1 (pin 4), Out 2 (pin 5) Active Active High Z Page 1 of 4 www.foxonline.com 3.2mm x 2.5mm LVPECL Oscillator FO3PS Available Options by Stability & Operating Temp Frequency Stability2 ±100PPM ±100PPM ±50PPM ±50PPM ±25PPM ±25PPM ±20PPM Operating Temperature (°C) -20 ~ +70 -40 ~ +85 -20 ~ +70 -40 ~ +85 -20 ~ +70 -40 ~ +85 -20 ~ +70 Frequency Range (MHz) 13.5 13.5 13.5 13.5 13.5 13.5 13.5 ~ 250 ~ 250 ~ 250 ~ 250 ~ 250 ~ 250 ~ 250 An internal pull-up resistor from pin 1 to pin 6 allows active output if pin 1 is left open. Inclusive of 25°C tolerance, operating temperature range, input voltage change, load change, Reflow, one-year aging, shock, and vibration. 3 Inclusive of 25°C tolerance, operating temperature range. 1 2 Revised A: 08/29/2019 Page 2 of 4 www.foxonline.com 3.2mm x 2.5mm LVPECL Oscillator FO3PS DIMENSIONS / MECHANICAL SPECIFICATIONS Note: 1, A 0.01μF capacitor should be placed between VDD (Pin 4) and GND (Pin2) to minimize power supply line noise. 2, Dimensional drawing is for reference to critical specifications defined by size measurements. Certain non-critical visual attributes, such as side castellation’s, etc. may vary. Revised A: 08/29/2019 Page 3 of 4 www.foxonline.com 3.2mm x 2.5mm LVPECL Oscillator FO3PS TAPE SPECIFICATIONS (mm) A B ø1.5 4.0 C 4.0 D E 3.5 8.0 REEL SPECIFICATIONS (mm) F REEL QTY G H I J K L M 1.4 -T2 = 2,000 -T1 = 1,000 2.0 Ø13 Ø21 Ø60 Ø180 9.0 1.2 Available Options & Part Identification* Sample PN: FO3PSCBM125.0-T2 F O3PS C B M 125.0 -T2 Fox Model Number Voltage J = 2.5V±10% C = 3.3V±10% Stability A = ±100PPM B = ±50PPM D = ±25PPM E = ±20PPM Operating Temperature F = -20 to +70˚C M = -40 to +85°C Frequency (MHz) Values Added Options Blank = Bulk T1 = 1,000 pcs T2 = 2,000 pcs *Not all frequencies in the frequency range, or every combination of stability, temp range, and voltage available. See stabilities and op temps for each VDD. Reliability Test Conditions Please contact Abracon Quality Assurance department Revised A: 08/29/2019 Page 4 of 4 www.foxonline.com