FO5LSCBM62.5-T1

FO5LS 5.0mm x 3.2mm SMD LVDS Oscillator (Former F530D/F540D families) Features • • • • LVDS Output Stabilities to ±20 PPM Operating Temperature Ranges to -40°C to +85°C Supply Voltages: 1.8V, 2.5V, 3.3V 2.5/3.3V SPECIFICATIONS PARAMETERS Frequency Range Temperature Range Storage (TSTG) Supply Voltage (VDD) Input Current (IDD) Standby Current Output Symmetry (50% VP-P) Rise Time (20%~80% VP-P) Fall Time (80%~20% VP-P) Differential Output Voltage (VOD) Differential Offset Voltage (VOS) Differential Output Voltage Swing (Vopp) Output Load (HCMOS) Start-up Time (TS) Output Disable Time 1 Output Enable Time 1 Aging (per year @ 25C) Phase Jitter (12kHz~20MHz) MAX (Unless otherwise noted) 13.5 ~ 250MHz -55°C ~ +125°C 2.5V±10% 50 mA 15 µA 45 % ~ 55 % 0.5 nS 0.5 nS 0.247V ~ 0.454V 1.125V ~ 1.375V 0.25Vpp min 100 Ohms Typical 10 mS 200 µS 10 mS ±3 PPM 1 pS 3.3V±10% 0.35Vpp min ENABLE / DISABLE FUNCTION Pin1 OPEN 1 ‘1’ Level VIH ≥ 70%VDD ‘0’ Level VIL ≤ 30%VDD Out 1 (pin 4), Out 2 (pin 5) Active Active High Z Available Options by Stability & Operating Temp Frequency Stability2 ±100PPM ±100PPM ±100PPM ±50PPM ±50PPM ±50PPM ±25PPM ±25PPM ±25PPM3 ±20PPM3 Revised A: 05/06/2020 Operating Temperature (°C) -10 ~ +70 -20 ~ +70 -40 ~ +85 -10 ~ +70 -20 ~ +70 -40 ~ +70 -10 ~ +85 -20 ~ +70 -40 ~ +85 -20 ~ +70 Frequency Range (MHz) 13.500 ~ 250.000 13.500 ~ 250.000 13.500 ~ 250.000 13.500 ~ 250.000 13.500 ~ 250.000 13.500 ~ 250.000 13.500 ~ 250.000 13.500 ~ 250.000 13.500 ~ 250.000 13.500 ~ 250.000 Page 1 of 4 www.foxonline.com FO5LS 5.0mm x 3.2mm SMD LVDS Oscillator (Former F530D/F540D families) 1.8V SPECIFICATIONS PARAMETERS Frequency Range Temperature Range Storage (TSTG) Supply Voltage (VDD) Input Current (IDD) Standby Current Output Symmetry (50% Vp-p) Rise Time (20%~80% VP-P) Fall Time (80%~20% VP-P) Differential Output Voltage (VOD) Differential Offset Voltage (VOS) Differential Output Voltage Swing (Vopp) Output Load (HCMOS) Start-up Time (TS) Output Disable Time 1 Output Enable Time 1 Aging (per year @ 25C) Phase Jitter (12kHz~20MHz) MAX (Unless otherwise noted) 100 ~ 170MHz -55°C ~ +125°C 1.8V±10% 66 mA 30 µA 45% ~ 55% 0.7 nS 0.7 nS 0.33V typ 1.125V ~ 1.375V (1.25V typ) 0.25Vp-p min 100 Ohms Typical 10 mS 200 nS 10 mS ±3 PPM 1 pS (0.5pS typ) ENABLE / DISABLE FUNCTION Pin1 OPEN 1 ‘1’ Level VIH ≥ 70%VDD ‘0’ Level VIL ≤ 30%VDD Out 1 (pin 4), Out 2 (pin 5) Active Active High Z Available Options by Stability & Operating Temp Frequency Stability2 ±100PPM ±100PPM ±50PPM ±50PPM ±25PPM ±25PPM3 Operating Temperature (°C) -20 ~ +70 -40 ~ +85 -20 ~ +70 -40 ~ +85 -20 ~ +70 -40 ~ +85 Frequency Range (MHz) 100.0 ~ 170.0 100.0 ~ 170.0 100.0 ~ 170.0 100.0 ~ 170.0 100.0 ~ 170.0 100.0 ~ 170.0 An internal pull-up resistor from pin 1 to pin 6 allows active output if pin 1 is left open Inclusive of 25°C tolerance, operating temperature range, input voltage change, load change, Reflow, one-year aging, shock, and vibration. 3 Inclusive of 25°C tolerance and operating temperature range. 1 2 Revised A: 05/06/2020 Page 2 of 4 www.foxonline.com FO5LS 5.0mm x 3.2mm SMD LVDS Oscillator (Former F530D/F540D families) DIMENSIONS / MECHANICAL SPECIFICATIONS ` Note: 1. A 0.01μF capacitor should be placed between VDD (Pin 6) and GND (Pin3) to minimize power supply line noise. 2. Dimensional drawing is for reference to critical specifications defined by size measurements. Certain non-critical visual attributes, such as side castellation’s, pin shape etc. may vary. STANDARD SPECIFICATIONS PARAMETERS Maximum Soldering Temp / Time Moisture Sensitivity Level (MSL) Termination Finish Seal Method Lead (Pb) Free REACH/REACH Compliant Revised A: 05/06/2020 MAX (Unless otherwise noted) 260°C / 10 Seconds x 2 1 Au over Ni Seam Yes Yes Page 3 of 4 www.foxonline.com FO5LS 5.0mm x 3.2mm SMD LVDS Oscillator (Former F530D/F540D families) TAPE SPECIFICATIONS (mm) REEL SPECIFICATIONS (mm) A B C D E F REEL QTY G H I J K L M ø1.5 4.0 480 3.5 16.0 1.4 -T1 = 1,000 2.0 Ø13 Ø21 Ø60 Ø180 13.0 2.0 Available Options & Part Identification for SMD LVDS Oscillator O5LS* Sample PN: FO5LSCDM125.0 -T1 F O5LS C D M 125.0 -T1 Fox Model Number Voltage K = 1.8V±5% J = 2.5V±10% C = 3.3V±10% Stability A = ±100 PPM B = ±50 PPM D = ±25 PPM E = ±20 PPM Operating Temperature E = -10 to +70°C F = -20 to +70°C M = -40 to +85°C Frequency (MHz) Reel Quantity Blank = Bulk T1 = 1,000 pcs * Not all frequencies in the frequency range, or every combination of stability, temp range, and voltage available. See stabilities and op temps for each VDD. Reliability Test Conditions Please contact Abracon Quality Assurance department Revised A: 05/06/2020 Page 4 of 4 www.foxonline.com