FO7LSCBM100.0-BULK

FO7LS 7.0mm x 5.0mm LVDS Oscillator (Former F4700, F4710 Series) Features • • • • LVDS Output Stabilities to ±20 PPM Temperature Ranges as wide as -40°C to +85°C Supply Voltages: 2.5V, 3.3V 2.5V ELECTRICAL CHARACTERISTICS PARAMETERS Frequency (FO) Storage Temperature Range (TSTG) Supply Voltage (VDD) Input Current (IDD) Standby Current Output Symmetry (50% VP-P ) Rise Time (20%~80% VP-P) Fall Time (80%~20% VP-P) Differential Output Voltage (VOD) Differential Offset Voltage (VOS) Output Termination Start-up Time (TS) Output Disable Time 1 Output Enable Time 1 Aging (per year @ 25C) Phase Jitter (12kHz~20MHz) MAX (Unless otherwise noted) 25.0 ~ 400.0 MHz -55 ~ +125°C 2.5V±10% 3.3V±10% 63 mA 30 µA 45% ~ 55% 0.5 nS 0.5 nS 0.247V ~ 0.454V 1.125V ~ 1.375V 100 Ohms Typical 10 mS 200 nS 10 mS ±3 PPM 1 pS ENABLE / DISABLE FUNCTION Pin OPEN 1 ‘1’ Level VIH ≥ 70%VDD ‘0’ Level VIL ≤ 30%VDD 1 Out 1 (pin 4), Out 2 (pin 5) Active Active High Z Available Options by Stability & Operating Temp for 2.5V Frequency Stability2 Operating Temperature (°C) Frequency Range (MHz) ±100PPM2 -10 ~ +70 25.0 ~ 400.0 2 ±100PPM -40 ~ +85 25.0 ~ 400.0 ±100PPM2 -40 ~ +105 25.0 ~ 300.0 ±50PPM2 -10 ~ +70 25.0 ~ 400.0 2 ±50PPM -40 ~ +85 25.0 ~ 400.0 ±50PPM2 -40 ~ +105 25.0 ~ 300.0 2 ±25PPM -10 ~ +70 25.0 ~ 400.0 ±25PPM3 -40 ~ +85 25.0 ~ 400.0 3 ±20PPM -10 ~ +70 25.0 ~ 400.0 An internal pull-up resistor from pin 1 to pin 6 allows active output if pin 1 is left open Inclusive of 25°C tolerance, operating temperature range, input voltage change, load change, Vibration, reflow, and one-year aging, shock, and vibration. 3 Inclusive of 25°C tolerance and operating temperature range. 1 2 Revised A: 05/05/2020 Page 1 of 3 www.foxonline.com FO7LS 7.0mm x 5.0mm LVDS Oscillator (Former F4700, F4710 Series) DIMENSIONS / MECHANICAL SPECIFICATIONS Note: *A 0.01μF capacitor should be placed between VDD (Pin 4) and GND (Pin2) to minimize power supply line noise. *Dimensional drawing is for reference to critical specifications defined by size measurements. certain non-critical visual attributes, such as side castellation’s, reference pin shape, etc. may vary STANDARD SPECIFICATIONS PARAMETERS Maximum Soldering Temp / Time Moisture Sensitivity Level (MSL) per J-STD-033 Termination Finish Seal Method Lead (Pb) Free RoHS Compliant REACH Compliant Revised A: 05/05/2020 MAX (Unless otherwise noted) 260°C / 10 Seconds x 2 1 Au (0.3~1µm) over Ni (1.27~8.89µm) Seam Yes Yes, no exemptions Yes Page 2 of 3 www.foxonline.com FO7LS 7.0mm x 5.0mm LVDS Oscillator (Former F4700, F4710 Series) TAPE SPECIFICATIONS (mm) REEL SPECIFICATIONS (mm) A B C D E F REEL QTY G H I J K L M ø1.55 4.0 8.0 7.5 16.0 2.1 -T2 = 2,000 -T1 = 1,000 2.0 Ø13 Ø21 Ø80 Ø255 17.5 2.0 Available Options & Part Identification for LVDS Oscillator O7LS* Sample PN: FO7LSCDM125.0-T2 F O7LS C D M 125.0 -T2 Fox Model Number Voltage Stability A = ±100PPM B = ±50PPM D = ±25PPM E = ±20 PPM Operating Temperature E = -10 to +70°C M = -40 to +85°C P = -40 to +105°C Frequency (MHz) Values Added Options Blank = Bulk T1 = 1,000 pcs T2 = 2,000 pcs J = 2.5V±10% C = 3.3V±10% * Not all frequencies in the frequency range, or every combination of stability, temp range, and voltage available. See stabilities and op temps table on page 2. Reliability Test Conditions Please contact Abracon Quality Assurance department Revised A: 05/05/2020 Page 3 of 3 www.foxonline.com