FO7PSJBM106.25-T1

FO7PS 7mm x 5mm LVPECL Oscillator (Former F4600, F4620 Series) ) Features • • • • LVPECL Output Stabilities to ±20 PPM Temperature Ranges -40°C to +85°C Supply Voltages: 2.5V, 3.3V 2.5V ELECTRICAL CHARACTERISTICS PARAMETERS Frequency Range Temperature Range Storage (TSTG) Supply Voltage (VDD) Input Current (IDD) Standby Current Output Symmetry (50% VDD) 40.000 ~ 170.000 MHz >170.000 ~ 325.000 MHz Rise Time (20%~80% VP-P) Fall Time (80%~20% VP-P) Output Voltage (VOL) (VOH) Output Load (HCMOS) Start-up Time (TS) Output Disable Time 1 Output Enable Time 1 Phase Jitter (12kHz~20MHz BW) MAX (Unless otherwise noted) 40.000 ~325.000 MHz -55°C ~ +125°C 2.5V±10% 88mA 30 µA 45% ~ 55% 40 % ~ 60 % 1nS 1nS 1.195V 1.415V Min. 50 Ohms to VDD – 2.0V 10 mS 200 nS 10 mS 0.3pS Typ. ENABLE / DISABLE FUNCTION Pin OPEN 1 ‘1’ Level VIH ≥ 70%VDD ‘0’ Level VIL ≤ 30%VDD 1 Out 1 (pin 4), Out 2 (pin 5) Active Active High Z Available Options by Stability & Operating Temp for 2.5V2 Frequency Stability2 ±100PPM ±100PPM ±100PPM ±50PPM ±50PPM ±50PPM ±25PPM ±25PPM ±25PPM Operating Temperature (°C) -10 ~ +70 -20 ~ +70 -40 ~ +85 -10 ~ +70 -20 ~ +70 -40 ~ +85 -10 ~ +70 -20 ~ +70 -40 ~ +85 Frequency Range (MHz) 40.000 ~ 325.000 40.000 ~ 325.000 40.000 ~ 325.000 40.000 ~ 325.000 40.000 ~ 325.000 40.000 ~ 325.000 40.000 ~ 325.000 40.000 ~ 325.000 40.000 ~ 200.000 1 An 2 internal pull-up resistor from pin 1 to pin 4 allows active output if pin 1 is left open Inclusive of 25°C tolerance, operating temperature range, input voltage change, load change, Shock, vibration, reflow, and one-year aging. (*Excludes shock and vibration) Revised A: 05/05/2020 Page 1 of 4 www.foxonline.com FO7PS 7mm x 5mm LVPECL Oscillator (Former F4600, F4620 Series) ) 3.3V ELECTRICAL CHARACTERISTICS PARAMETERS Frequency Range Temperature Range Storage (TSTG) Supply Voltage (VDD) Input Current (IDD) Standby Current Output Symmetry (50% VDD) 40.000 ~ 170.000 MHz >170.000 ~ 325.000 MHz Rise Time (20%~80% VP-P) Fall Time (80%~20% VP-P) Output Voltage (VOL) (VOH) Output Load (HCMOS) Start-up Time (TS) Output Disable Time 1 Output Enable Time 1 Phase Jitter (12kHz~20MHz BW) MAX (Unless otherwise noted) 40.000 ~325.000 MHz -55°C ~ +125°C 3.3V±10% 88mA 30 µA 45% ~ 55% 40 % ~ 60 % 1nS 1nS 1.7V 2.2V Min. 50 Ohms to VDD – 2.0V 10 mS 100 nS 10 mS 0.3pS Typ. ENABLE / DISABLE FUNCTION Pin OPEN 1 ‘1’ Level VIH ≥ 70%VDD ‘0’ Level VIL ≤ 30%VDD 2 Out 1 (pin 4), Out 2 (pin 5) Active Active High Z Available Options by Stability & Operating Temp for 3.3V2 Frequency Stability2 ±100PPM ±100PPM ±100PPM ±50PPM ±50PPM ±50PPM ±25PPM ±25PPM ±25PPM ±20PPM ±20PPM 1 2 Operating Temperature (°C) -10 ~ +70 -20 ~ +70 -40 ~ +85 -10 ~ +70 -20 ~ +70 -40 ~ +85 -10 ~ +70* -20 ~ +70* -40 ~ +85* -10 ~ +70* -20 ~ +70* Frequency Range (MHz) 40.000 ~ 325.000 40.000 ~ 325.000 40.000 ~ 325.000 40.000 ~ 325.000 40.000 ~ 325.000 40.000 ~ 325.000 40.000 ~ 325.000 40.000 ~ 325.000 40.000 ~ 280.000 40.000 ~ 280.000 40.000 ~ 280.000 An internal pull-up resistor from pin 2 to pin 6 allows active output if pin 1 is left open Inclusive of 25°C tolerance, operating temperature range, input voltage change, load change, Shock, vibration. (*Excludes shock and vibration) Revised A: 05/05/2020 Page 2 of 4 www.foxonline.com FO7PS 7mm x 5mm LVPECL Oscillator (Former F4600, F4620 Series) ) DIMENSIONS / MECHANICAL SPECIFICATIONS ` Note: * A 0.01μF capacitor should be placed between VDD (Pin 4) and GND (Pin2) to minimize power supply line noise. *Dimensional drawing is for reference to critical specifications defined by size measurements. Certain non-critical visual attributes, such as side castellation’s, etc. may vary. STANDARD SPECIFICATIONS PARAMETERS Maximum Soldering Temp / Time Moisture Sensitivity Level (MSL) Termination Finish Seal Method Lead (Pb) Free RoHS /REACH Compliant (latest version) Revised A: 05/05/2020 MAX (Unless otherwise noted) 260°C / 10 Seconds x 2 1 Au over Ni Seam Yes Yes Page 3 of 4 www.foxonline.com FO7PS 7mm x 5mm LVPECL Oscillator (Former F4600, F4620 Series) ) TAPE SPECIFICATIONS (mm) A B ø1.5 4.0 C 8.0 D E 7.5 16.0 REEL SPECIFICATIONS (mm) F STD REEL QTY G H I J K L M 2.15 -T1 = 1,000 -T2 = 2,000 2.0 Ø13 Ø21 Ø80 Ø255 17.5 2.0 Available Options & Part Identification for O7PS* Sample PN: FO7PSCBM62.5-T1 F O7PS C B M 62.5 -T1 Fox Model Number Voltage J = 2.5V±10% C = 3.3V±10% Stability A = ±100PPM B = ±50PPM D = ±25PPM E = ±20PPM Operating Temperature E = -10 to +70˚C F = -20 to +70˚C M = -40 to +85°C Frequency (MHz) Values Added Options Blank = Bulk T1 = 1,000 pcs T2 = 2,000 pcs *Not all frequencies in the frequency range, or every combination of stability, temp range, and voltage available. See stabilities and op temps for each VDD. Reliability Test Conditions Please contact Abracon Quality Assurance department Revised A: 05/05/2020 Page 4 of 4 www.foxonline.com