56F8335_07

56F8335/56F8135 Data Sheet Preliminary Technical Data 56F8300 16-bit Digital Signal Controller MC56F8335 Rev. 5 01/2007 freescale.com Document Revision History Version History Rev. 0 Rev. 1 Initial Release Deleted RSTO from Pin Group 2 (listed after Table 10-1). Deleted formula for Max Ambient Operating Temperature (Automotive) and Max Ambient Operating Temperature (Industrial) in Table 10-4. Added RoHS-compliance and “pb-free” language to back cover. Added information/corrected state during reset in Table 2-2. Clarified external reference crystal frequency for PLL in Table 10-14 by increasing maximum value to 8.4MHz. Replaced “Tri-stated” with an explanation in State During Reset column in Table 2-2. Revised Table 4-4 to include correct program Flash size. • Added the following note to the description of the TMS signal in Table 2-2: Note: Always tie the TMS pin to VDD through a 2.2K resistor. • Added the following note to the description of the TRST signal in Table 2-2: Note: For normal operation, connect TRST directly to VSS. If the design is to be used in a debugging environment, TRST may be tied to VSS through a 1K resistor. Description of Change Rev. 2 Rev. 3 Rev. 4 Rev. 5 Please see http://www.freescale.com for the most current data sheet revision. 56F8335 Technical Data, Rev. 5 2 Freescale Semiconductor Preliminary 56F8335/56F8135 General Description Note: Features in italics are NOT available in the 56F8135 device. • Up to 60 MIPS at 60MHz core frequency • DSP and MCU functionality in a unified, C-efficient architecture • 64KB Program Flash • 4KB Program RAM • 8KB Data Flash • 8KB Data RAM • 8KB Boot Flash • Up to two 6-channel PWM modules • Four 4-channel, 12-bit ADCs • Temperature Sensor • Up to two Quadrature Decoders • FlexCAN module • Optional On-Chip Regulator • Two Serial Communication Interfaces (SCIs) • Up to two Serial Peripheral Interface (SPIs) • Up to four general-purpose Quad Timers • Computer Operating Properly (COP)/Watchdog • JTAG/Enhanced On-Chip Emulation (OnCE™) for unobtrusive, real-time debugging • Up to 49 GPIO lines • 128-pin LQFP Package RSTO RESET 6 PWM Outputs 3 4 Current Sense Inputs or GPIOC Fault Inputs Program Controller and Hardware Looping Unit 5 JTAG/ EOnCE Port VPP 2 VCAP 4 OCR_DIS VDD VSS 7 5 Digital Reg VDDA 2 VSSA PWMA Analog Reg 16-Bit 56800E Core Low Voltage Supervisor Bit Manipulation Unit 6 PWM Outputs 3 4 4 4 5 4 4 Current Sense Inputs or GPIOD Fault Inputs PWMB Address Generation Unit Data ALU 16 x 16 + 36 -->36-Bit MAC Three 16-bit Input Registers Four 36-bit Accumulators AD0 AD1 VREF PAB PDB CDBR CDBW ADCA Memory Program Memory 32K x 16 Flash 2K x 16 RAM 4K x 16 Boot Flash Data Memory 4K x 16 Flash 4K x 16 RAM XDB2 XAB1 XAB2 PDB CDBR CDBW R/W Control AD0 ADCB AD1 TEMP_SENSE 4 Quadrature Decoder 0 or Quad Timer A or GPIOC Quadrature Decoder 1 or Quad Timer B or SP1I or GPIOC Quad Timer C or GPIOE Quad Timer D or GPIOE FlexCAN System Bus Control External Bus Interface Unit PAB * External Address Bus Switch * External Data Bus Switch * Bus Control 6 5 A8-13 or GPIOA0-5 GPIOB0-4 or A16-20 4 D7-10 or GPIOF0-3 6 GPIOD0-5 or CS2-7 4 IPBus Bridge (IPBB) Peripheral Device Selects 2 4 2 Decoding Peripherals RW Control IPAB IPWDB IPRDB Clock resets P System O Integration R Module PLL * EMI not functional in this package; use as GPIO pins SPI0 or GPIOE 4 SCI1 or GPIOD 2 SCI0 or GPIOE 2 COP/ Interrupt Watchdog Controller O Clock S Generator C XTAL EXTAL IRQA IRQB CLKO CLKMODE 56F8335/56F8135 Block Diagram - 128 LQFP 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 3 Table of Contents Part 1: Overview . . . . . . . . . . . . . . . . . . . . . . . 5 1.1. 1.2. 1.3. 1.4. 1.5. 1.6. 56F8335/56F8135 Features . . . . . . . . . . . . . . .5 Device Description . . . . . . . . . . . . . . . . . . . . . 7 Award-Winning Development Environment . . .9 Architecture Block Diagram . . . . . . . . . . . . . . . 9 Product Documentation . . . . . . . . . . . . . . . . . 12 Data Sheet Conventions . . . . . . . . . . . . . . . . 13 Part 8: General Purpose Input/Output (GPIO) . . . . . . . . . . . . . . . . . . . . . . 120 8.1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 120 8.2. Memory Maps . . . . . . . . . . . . . . . . . . . . . . . 120 8.3. Configuration . . . . . . . . . . . . . . . . . . . . . . . . 120 Part 9: Joint Test Action Group (JTAG) . . 125 9.1. JTAG Information . . . . . . . . . . . . . . . . . . . . 125 Part 2: Signal/Connection Descriptions . . 14 2.1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . 14 2.2. Signal Pins . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Part 10: Specifications. . . . . . . . . . . . . . . . 126 10.1. General Characteristics. . . . . . . . . . . . . . . 126 10.2. DC Electrical Characteristics. . . . . . . . . . . 130 10.3. AC Electrical Characteristics . . . . . . . . . . . 134 10.4. Flash Memory Characteristics . . . . . . . . . . 134 10.5. External Clock Operation Timing . . . . . . . 135 10.6. Phase Locked Loop Timing. . . . . . . . . . . . 135 10.7. Crystal Oscillator Timing . . . . . . . . . . . . . . 136 10.8. Reset, Stop, Wait, Mode Select and Interrupt Timing . . . . . . . . . . . 136 10.9. Serial Peripheral Interface (SPI) Timing . . . 138 10.10. Quad Timer Timing . . . . . . . . . . . . . . . . . 142 10.11. Quadrature Decoder Timing . . . . . . . . . . . 142 10.12. Serial Communication Interface (SCI) Timing . . . . . . . . . . . . . . . . . 143 10.13. Controller Area Network (CAN) Timing . . 144 10.14. JTAG Timing . . . . . . . . . . . . . . . . . . . . . . 144 10.15. Analog-to-Digital Converter ( ADC) Parameters . . . . . . . . . . . . . 146 10.16. Equivalent Circuit for ADC Inputs . . . . . . 148 10.17. Power Consumption . . . . . . . . . . . . . . . . 149 Part 3: On-Chip Clock Synthesis (OCCS) . 33 3.1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . 33 3.2. External Clock Operation . . . . . . . . . . . . . . . 33 3.3. Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Part 4: Memory Map. . . . . . . . . . . . . . . . . . . 35 4.1. 4.2. 4.3. 4.4. 4.5. 4.6. 4.7. 4.8. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Program Map. . . . . . . . . . . . . . . . . . . . . . . . . 36 Interrupt Vector Table . . . . . . . . . . . . . . . . . . .37 Data Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Flash Memory Map . . . . . . . . . . . . . . . . . . . . 42 EOnCE Memory Map . . . . . . . . . . . . . . . . . . .43 Peripheral Memory Mapped Registers . . . . . .44 Factory Programmed Memory. . . . . . . . . . . . 71 Part 5: Interrupt Controller (ITCN) . . . . . . . . 71 5.1. 5.2. 5.3. 5.4. 5.5. 5.6. 5.7. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . 71 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 Functional Description . . . . . . . . . . . . . . . . . . 71 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . 73 Operating Modes . . . . . . . . . . . . . . . . . . . . . . 73 Register Descriptions . . . . . . . . . . . . . . . . . . .74 Resets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99 Part 11: Packaging . . . . . . . . . . . . . . . . . . 152 11.1. 56F8335 Package and Pin-Out Information . . . . . . . . . . . . 152 11.2. 56F8135 Package and Pin-Out Information . . . . . . . . . . . . 155 Part 6: System Integration Module (SIM) . 100 6.1. 6.2. 6.3. 6.4. 6.5. 6.6. 6.7. 6.8. 6.9. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . Features . . . . . . . . . . . . . . . . . . . . . . . . . . . Operating Modes . . . . . . . . . . . . . . . . . . . . . Operating Mode Register . . . . . . . . . . . . . . Register Descriptions . . . . . . . . . . . . . . . . . Clock Generation Overview. . . . . . . . . . . . . Power-Down Modes Overview . . . . . . . . . . Stop and Wait Mode Disable Function . . . . Resets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 100 101 101 102 114 115 116 116 Part 12: Design Considerations . . . . . . . . 159 12.1. Thermal Design Considerations . . . . . . . . . 159 12.2. Electrical Design Considerations . . . . . . . 159 12.3. Power Distribution and I/O Ring Implementation . . . . . . . . . . . . . . . 159 Part 13: Ordering Information . . . . . . . . . . 159 Part 7: Security Features . . . . . . . . . . . . . 117 7.1. Operation with Security Enabled . . . . . . . . .117 7.2. Flash Access Blocking Mechanisms . . . . . .117 56F8335 Technical Data, Rev. 5 4 Freescale Semiconductor Preliminary 56F8335/56F8135 Features Part 1 Overview 1.1 56F8335/56F8135 Features 1.1.1 • • • • • • • • • • • • • • Core Efficient 16-bit 56800E family controller engine with dual Harvard architecture Up to 60 Million Instructions Per Second (MIPS) at 60MHz core frequency Single-cycle 16 × 16-bit parallel Multiplier-Accumulator (MAC) Four 36-bit accumulators, including extension bits Arithmetic and logic multi-bit shifter Parallel instruction set with unique DSP addressing modes Hardware DO and REP loops Three internal address buses Four internal data buses Instruction set supports both DSP and controller functions Controller-style addressing modes and instructions for compact code Efficient C compiler and local variable support Software subroutine and interrupt stack with depth limited only by memory JTAG/EOnCE debug programming interface 1.1.2 Differences Between Devices Table 1-1 outlines the key differences between the 56F8335 and 56F8135 devices. Table 1-1 Device Differences Feature Guaranteed Speed Program RAM Data Flash PWM CAN Quad Timer Quadrature Decoder Temperature Sensor 56F8335 60MHz/60 MIPS 4KB 8KB 2x6 1 4 2x4 1 56F8135 40MHz/40MIPS Not Available Not Available 1x6 Not Available 2 1x4 Not Available 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 5 1.1.3 • • • Memory Harvard architecture permits as many as three simultaneous accesses to program and data memory Flash security protection feature On-chip memory, including a low-cost, high-volume Flash solution — 64KB of Program Flash — 4KB of Program RAM — 8KB of Data Flash — 8KB of Data RAM — 8KB of Boot Flash Note: Features in italics are NOT available in the 56F8135 device. • EEPROM emulation capability 1.1.4 • Peripheral Circuits Pulse Width Modulator module: — In the 56F8335, two Pulse Width Modulator modules, each with six PWM outputs, three Current Sense inputs, and four Fault inputs; fault-tolerant design with dead time insertion; supports both center-aligned and edge-aligned modes — In the 56F8135, one Pulse Width Modulator module with six PWM outputs, three Current Sense inputs and three Fault inputs; fault-tolerant design with dead time insertion; supports both center-aligned and edge-aligned modes Note: Features in italics are NOT available in the 56F8135 device. • • Four 12-bit, Analog-to-Digital Converters (ADCs), which support four simultaneous conversions with quad, 4-pin multiplexed inputs; ADC and PWM modules can be synchronized through Timer C, channels 2 and 3 Quadrature Decoder: — In the 56F8335, two four-input Quadrature Decoders or two additional Quad Timers — In the 56F8135, one four-input Quadrature Decoder, which works in conjunction with Quad Timer A Temperature Sensor can be connected, on the board, to any of the ADC inputs to monitor the on-chip temperature Quad Timer: — In the 56F8335, four dedicated general-purpose Quad Timers totaling six dedicated pins: Timer C with two pins and Timer D with four pins — In the 56F8135, two Quad Timers; Timer A and Timer C both work in conjunction with GPIO Optional On-Chip Regulator FlexCAN (CAN Version 2.0 B-compliant) module with 2-pin port for transmit and receive Two Serial Communication Interfaces (SCIs), each with two pins (or four additional GPIO lines) Up to two Serial Peripheral Interfaces (SPIs), both with configurable 4-pin port (or eight additional GPIO lines); SPI 1 can also be used as Quadrature Decoder 1 or Quad Timer B Computer Operating Properly (COP)/Watchdog timer Two dedicated external interrupt pins • • • • • • • • 56F8335 Technical Data, Rev. 5 6 Freescale Semiconductor Preliminary Device Description • • • • • • 49 General Purpose I/O (GPIO) pins; 28 pins dedicated to GPIO External reset input pin for hardware reset External reset output pin for system reset Integrated low-voltage interrupt module JTAG/Enhanced On-Chip Emulation (OnCE) for unobtrusive, processor speed-independent, real-time debugging Software-programmable, Phase Lock Loop-based frequency synthesizer for the core clock 1.1.5 • • • • • • Energy Information Fabricated in high-density CMOS with 5V-tolerant, TTL-compatible digital inputs On-board 3.3V down to 2.6V voltage regulator for powering internal logic and memories; can be disabled On-chip regulators for digital and analog circuitry to lower cost and reduce noise Wait and Stop modes available ADC smart power management Each peripheral can be individually disabled to save power 1.2 Device Description The 56F8335 and 56F8135 are members of the 56800E core-based family of controllers. Each combines, on a single chip, the processing power of a Digital Signal Processor (DSP) and the functionality of a microcontroller with a flexible set of peripherals to create an extremely cost-effective solution. Because of their low cost, configuration flexibility, and compact program code, the 56F8335 and 56F8135 are well-suited for many applications. The devices include many peripherals that are especially useful for motion control, smart appliances, steppers, encoders, tachometers, limit switches, power supply and control, automotive control (56F8335 only), engine management, noise suppression, remote utility metering, industrial control for power, lighting, and automation applications. The 56800E core is based on a Harvard-style architecture consisting of three execution units operating in parallel, allowing as many as six operations per instruction cycle. The MCU-style programming model and optimized instruction set allow straightforward generation of efficient, compact DSP and control code. The instruction set is also highly efficient for C/C++ Compilers to enable rapid development of optimized control applications. The 56F8335 and 56F8135 support program execution from internal memories. Two data operands can be accessed from the on-chip data RAM per instruction cycle. These devices also provide two external dedicated interrupt lines and up to 49 General Purpose Input/Output (GPIO) lines, depending on peripheral configuration. 1.2.1 56F8335 Features The 56F8335 includes 64KB of Program Flash and 8KB of Data Flash (each programmable through the JTAG port) with 4KB of Program RAM and 8KB of Data RAM. A total of 8KB of Boot Flash is incorporated for easy customer inclusion of field-programmable software routines that can be used to program the main Program and Data Flash memory areas. Both Program and Data Flash memories can be 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 7 independently bulk erased or erased in pages. Program Flash page erase size is 1KB. Boot and Data Flash page erase size is 512 bytes. The Boot Flash memory can also be either bulk or page erased. A key application-specific feature of the 56F8335 is the inclusion of two Pulse Width Modulator (PWM) modules. These modules each incorporate three complementary, individually programmable PWM signal output pairs (each module is also capable of supporting six independent PWM functions, for a total of 12 PWM outputs) to enhance motor control functionality. Complementary operation permits programmable dead time insertion, distortion correction via current sensing by software, and separate top and bottom output polarity control. The up-counter value is programmable to support a continuously variable PWM frequency. Edge-aligned and center-aligned synchronous pulse width control (0% to 100% modulation) is supported. The device is capable of controlling most motor types: ACIM (AC Induction Motors); both BDC and BLDC (Brush and Brushless DC motors); SRM and VRM (Switched and Variable Reluctance Motors); and stepper motors. The PWMs incorporate fault protection and cycle-by-cycle current limiting with sufficient output drive capability to directly drive standard optoisolators. A “smoke-inhibit”, write-once protection feature for key parameters is also included. A patented PWM waveform distortion correction circuit is also provided. Each PWM is double-buffered and includes interrupt controls to permit integral reload rates to be programmable from 1 to 16. The PWM modules provide reference outputs to synchronize the Analog-to-Digital Converters through two channels of Quad Timer C. The 56F8335 incorporates two Quadrature Decoders capable of capturing all four transitions on the two-phase inputs, permitting generation of a number proportional to actual position. Speed computation capabilities accommodate both fast- and slow-moving shafts. An integrated watchdog timer in the Quadrature Decoder can be programmed with a time-out value to alert when no shaft motion is detected. Each input is filtered to ensure only true transitions are recorded. This controller also provides a full set of standard programmable peripherals that include two Serial Communications Interfaces (SCIs); two Serial Peripheral Interfaces (SPIs); and four Quad Timers. Any of these interfaces can be used as General Purpose Input/Outputs (GPIOs) if that function is not required. A Flex Controller Area Network (FlexCAN) interface (CAN Version 2.0 B-compliant) and an internal interrupt controller are also a part of the 56F8335. 1.2.2 56F8135 Features The 56F8135 includes 64KB of Program Flash, programmable through the JTAG port, and 8KB of Data RAM. A total of 8KB of Boot Flash is incorporated for easy customer inclusion of field-programmable software routines that can be used to program the main Program Flash memory area. The Program Flash memory can be independently bulk erased or erased in pages; Program Flash page erase size is 1KB. The Boot Flash page erase size is 512 bytes; Boot Flash memory can also be either bulk or page erased. A key application-specific feature of the 56F8135 is the inclusion of one Pulse Width Modulator (PWM) module. This module incorporates three complementary, individually programmable PWM signal output pairs and can also support six independent PWM functions to enhance motor control functionality. Complementary operation permits programmable dead time insertion, distortion correction via current sensing by software, and separate top and bottom output polarity control. The up-counter value is programmable to support a continuously variable PWM frequency. Edge-aligned and center-aligned synchronous pulse width control (0% to 100% modulation) is supported. The device is capable of controlling most motor types: ACIM (AC Induction Motors); both BDC and BLDC (Brush and Brushless 56F8335 Technical Data, Rev. 5 8 Freescale Semiconductor Preliminary Award-Winning Development Environment DC motors); SRM and VRM (Switched and Variable Reluctance Motors); and stepper motors. The PWM incorporates fault protection and cycle-by-cycle current limiting with sufficient output drive capability to directly drive standard optoisolators. A “smoke-inhibit”, write-once protection feature for key parameters is also included. A patented PWM waveform distortion correction circuit is also provided. The PWM is double-buffered and includes interrupt controls to permit integral reload rates to be programmable from 1 to 16. The PWM module provides reference outputs to synchronize the Analog-to-Digital Converters through two channels of Quad Timer C. The 56F8135 incorporates a Quadrature Decoder capable of capturing all four transitions on the two-phase inputs, permitting generation of a number proportional to actual position. Speed computation capabilities accommodate both fast- and slow-moving shafts. An integrated watchdog timer in the Quadrature Decoder can be programmed with a time-out value to alert when no shaft motion is detected. Each input is filtered to ensure only true transitions are recorded. This controller also provides a full set of standard programmable peripherals that include two Serial Communications Interfaces (SCIs); two Serial Peripheral Interfaces (SPIs); and two Quad Timers. Any of these interfaces can be used as General Purpose Input/Outputs (GPIOs) if that function is not required. An internal interrupt controller is also a part of the 56F8135. 1.3 Award-Winning Development Environment Processor ExpertTM (PE) provides a Rapid Application Design (RAD) tool that combines easy-to-use component-based software application creation with an expert knowledge system. The CodeWarrior Integrated Development Environment is a sophisticated tool for code navigation, compiling, and debugging. A complete set of evaluation modules (EVMs) and development system cards will support concurrent engineering. Together, PE, CodeWarrior and EVMs create a complete, scalable tools solution for easy, fast, and efficient development. 1.4 Architecture Block Diagram Note: Features in italics are NOT available in the 56F8135 device and are shaded in the following figures. The 56F8335/56F8135 architecture is shown in Figure 1-1 and Figure 1-2. Figure 1-1 illustrates how the 56800E system buses communicate with internal memories and the IPBus Bridge. Table 1-2 lists the internal buses in the 56800E architecture and provides a brief description of their function. Figure 1-2 shows the peripherals and control blocks connected to the IPBus Bridge. The figures do not show the on-board regulator and power and ground signals. They also do not show the multiplexing between peripherals or the dedicated GPIOs. Please see Part 2, Signal/Connection Descriptions, to see which signals are multiplexed with those of other peripherals. Also shown in Figure 1-2 are connections between the PWM, Timer C and ADC blocks. These connections allow the PWM and/or Timer C to control the timing of the start of ADC conversions. The Timer C channel indicated can generate periodic start (SYNC) signals to the ADC to start its conversions. In another operating mode, the PWM load interrupt (SYNC output) signal is routed internally to the Timer C input channel as indicated. The timer can then be used to introduce a controllable delay before generating its output signal. The timer output then triggers the ADC. To fully understand this interaction, please see the 56F8300 Peripheral User’s Manual for clarification on the operation of all three of these peripherals. 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 9 5 JTAG / EOnCE Boot Flash pdb_m[15:0] pab[20:0] Program Flash Program RAM cdbw[31:0] 56800E EMI* CHIP TAP Controller 11 4 6 Address Data Control TAP Linking Module xab1[23:0] xab2[23:0] Data RAM External JTAG Port cdbr_m[31:0] xdb2_m[15:0 Data Flash IPBus Bridge NOT available on the 56F8135 device. * EMI not functional in this package; since only part of the address/data bus is bonded out, use as GPIO pins To Flash Control Logic Flash Memory Module IPBus Figure 1-1 System Bus Interfaces Note: Flash memories are encapsulated within the Flash Memory (FM) Module. Flash control is accomplished by the I/O to the FM over the peripheral bus, while reads and writes are completed between the core and the Flash memories. The primary data RAM port is 32 bits wide. Other data ports are 16 bits. Note: 56F8335 Technical Data, Rev. 5 10 Freescale Semiconductor Preliminary Architecture Block Diagram To/From IPBus Bridge CLKGEN (OSC / PLL) Interrupt Controller Low-Voltage Interrupt Timer A 4 4 POR & LVI System POR SIM RESET Quadrature Decoder 0 Timer D COP Reset Timer B 4 COP FlexCAN 2 Quadrature Decoder 1 SPI1 PWMA 13 SYNC Output GPIOA GPIOB GPIOC GPIOD PWMB SYNC Output ch3i Timer C ch3o 13 ch2i ch2o 2 GPIOE GPIOF 4 2 2 SPI0 SCI0 SCI1 IPBus NOT available on the 56F8135 device. ADCB ADCA TEMP_SENSE 1 8 8 Note: ADC A and ADC B use the same voltage reference circuit with VREFH, VREFP, VREFMID, VREFN, and VREFLO pins. Figure 1-2 Peripheral Subsystem 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 11 Table 1-2 Bus Signal Names Name Function Program Memory Interface pdb_m[15:0] cdbw[15:0] pab[20:0] cdbr_m[31:0] cdbw[31:0] xab1[23:0] Program data bus for instruction word fetches or read operations. Primary core data bus used for program memory writes. (Only these 16 bits of the cdbw[31:0] bus are used for writes to program memory.) Program memory address bus. Data is returned on pdb_m bus. Primary Data Memory Interface Bus Primary core data bus for memory reads. Addressed via xab1 bus. Primary core data bus for memory writes. Addressed via xab1 bus. Primary data address bus. Capable of addressing bytes1, words, and long data types. Data is written on cdbw and returned on cdbr_m. Also used to access memory-mapped I/O. Secondary Data Memory Interface xdb2_m[15:0] xab2[23:0] Secondary data bus used for secondary data address bus xab2 in the dual memory reads. Secondary data address bus used for the second of two simultaneous accesses. Capable of addressing only words. Data is returned on xdb2_m. Peripheral Interface Bus IPBus [15:0] Peripheral bus accesses all on-chip peripherals registers. This bus operates at the same clock rate as the Primary Data Memory and therefore generates no delays when accessing the processor. Write data is obtained from cdbw. Read data is provided to cdbr_m. 1. Byte accesses can only occur in the bottom half of the memory address space. The MSB of the address will be forced to 0. 1.5 Product Documentation The documents listed in Table 1-3 are required for a complete description and proper design with the 56F8335 and 56F8135 devices. Documentation is available from local Freescale distributors, Freescale semiconductor sales offices, Freescale Literature Distribution Centers, or online at http://www.freescale.com. Table 1-3 Chip Documentation Topic DSP56800E Reference Manual 56F8300 Peripheral User Manual 56F8300 SCI/CAN Bootloader User Manual 56F8335/56F8135 Technical Data Sheet Errata Description Detailed description of the 56800E family architecture, 16-bit hybrid controller core processor, and the instruction set Detailed description of peripherals of the 56F8300 family of devices Detailed description of the SCI/CAN Bootloaders 56F8300 family of devices Electrical and timing specifications, pin descriptions, device specific peripheral information and package descriptions (this document) Details any chip issues that might be present Order Number DSP56800ERM MC56F8300UM MC56F83xxBLUM MC56F8335 MC56F8335E MC56F8135E 56F8335 Technical Data, Rev. 5 12 Freescale Semiconductor Preliminary Data Sheet Conventions 1.6 Data Sheet Conventions This data sheet uses the following conventions: OVERBAR This is used to indicate a signal that is active when pulled low. For example, the RESET pin is active when low. A high true (active high) signal is high or a low true (active low) signal is low. A high true (active high) signal is low or a low true (active low) signal is high. Signal/Symbol PIN PIN PIN PIN Logic State True False True False Signal State Asserted Deasserted Asserted Deasserted Voltage1 VIL/VOL VIH/VOH VIH/VOH VIL/VOL “asserted” “deasserted” Examples: 1. Values for VIL, VOL, VIH, and VOH are defined by individual product specifications. 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 13 Part 2 Signal/Connection Descriptions 2.1 Introduction The input and output signals of the 56F8335 and 56F8135 are organized into functional groups, as detailed in Table 2-2 and as illustrated in Figure 2-1. In Table 2-2, each table row describes the signal or signals present on a pin. Table 2-1 Functional Group Pin Allocations Functional Group Power (VDD or VDDA) Power Option Control Ground (VSS or VSSA) Supply Capacitors1 & VPP PLL and Clock Bus Control Interrupt and Program Control Pulse Width Modulator (PWM) Ports Serial Peripheral Interface (SPI) Port 0 Serial Peripheral Interface (SPI) Port 1 Quadrature Decoder Port 02 Quadrature Decoder Port 13 Serial Communications Interface (SCI) Ports CAN Ports Analog-to-Digital Converter (ADC) Ports Timer Module Ports JTAG/Enhanced On-Chip Emulation (EOnCE) Temperature Sense Dedicated GPIO (Address Bus = 11; Data Bus = 44) Number of Pins in Package 56F8335 9 1 6 6 4 6 4 26 4 — 4 4 4 2 21 6 5 1 28 56F8135 9 1 6 6 4 6 4 13 4 4 4 — 4 — 21 4 5 — 28 1. If the on-chip regulator is disabled, the VCAP pins serve as 2.5V VDD_CORE power inputs 2. Alternately, can function as Quad Timer pins or GPIO 3. Pins in this section can function as Quad Timer, SPI 1, or GPIO 4. EMI not functional in these packages; use as GPIO pins. Note: See Table 1-1 for 56F8135 functional differences. 56F8335 Technical Data, Rev. 5 14 Freescale Semiconductor Preliminary Introduction Power Power Power Ground Ground VDD_IO VDDA_ADC VDDA_OSC_PLL VSS VSSA_ADC OCR_DIS 7 1 1 5 1 1 4 2 1 1 1 1 6 5 1 1 1 1 PHASEA0 (TA0, GPIOC4) PHASEB0(TA1, GPIOC5) INDEX0 (TA2, GPIOC6) HOME0 (TA3, GPIOC7) SCLK0 (GPIOE4) MOSI0 (GPIOE5) MISO0 (GPIOE6) SS0 (GPIOE7) PHASEA1(TB0, SCLK1, GPIOC0) PHASEB1 (TB1, MOSI1, GPIOC1) INDEX1 (TB2, MISO1, GPIOC2) HOME1 (TB3, SS1, GPIOC3) PWMA0 - 5 ISA0 - 2 (GPIOC8 - 10) FAULTA0 - 3 PWMB0 - 5 ISB0 - 2 (GPIOD10 - 12) FAULTB0-3 ANA0 - 7 VREF ANB0 - 7 TEMP_SENSE CAN_RX CAN_TX TC0 - 1 (GPIOE8 - 9) TD0 - 3 (GPIOE10 - 13) Quadrature Decoder 0 or Quad Timer A or GPIO 56F8335 1 1 1 1 1 1 1 1 Other Supply Ports PLL and Clock VCAP1 - VCAP4 VPP1 & VPP2 CLKMODE EXTAL XTAL CLKO A8 - A13 (GPIOA0 - 5) GPIOB0-4 (A16 - 20) SPI0 or GPIO Quadrature Decoder 1 or Quad Timer B or SPI1 or GPIO *External Address Bus or GPIO 6 3 4 6 PWMA *External Data Bus D7 - D10 (GPIOF0 - 3) 4 3 4 PWMB *External Bus Control GPIOD0 - 5 (CS2 - 7) 8 6 5 8 1 ADCA ADCB Temperature Sensor SCI0 or GPIOE SCI1 or GPIO TXD0 (GPIOE0) RXD0 (GPIOE1) TXD1 (GPIOD6) RXD1 (GPIOD7) TCK TMS TDI TDO TRST 1 1 1 1 1 1 1 1 1 1 1 2 4 CAN Quad Timer C and D or GPIO JTAG/ EOnCE Port 1 1 1 1 IRQA IRQB RESET RSTO Interrupt/ Program Control * EMI not functional in this package; use as GPIO pins Figure 2-1 56F8335 Signals Identified by Functional Group1 (128-Pin LQFP) 1. Alternate pin functionality is shown in parenthesis; pin direction/type shown is the default functionality. 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 15 Power Power Power Ground Ground VDD_IO VDDA_ADC VDDA_OSC_PLL VSS VSSA_ADC OCR_DIS 7 1 1 5 1 1 4 2 1 1 1 1 6 5 1 1 1 1 PHASEA0 (TA0, GPIOC4) PHASEB0(TA1, GPIOC5) INDEX0 (TA2, GPIOC6) HOME0 (TA3, GPIOC7) SCLK0 (GPIOE4) MOSI0 (GPIOE5) MISO0 (GPIOE6) SS0 (GPIOE7) (SCLK1, GPIOC0) (MOSI1, GPIOC1) (MISO1, GPIOC2) (SS1,GPIOC3) Quadrature Decoder 0 or Quad Timer A or GPIO 56F8135 1 1 1 1 1 1 1 1 Other Supply Ports PLL and Clock VCAP1 - VCAP4 VPP1 & VPP2 CLKMODE EXTAL XTAL CLKO A8 - A13 (GPIOA0 - 5) GPIOB0-4 (A16 - 20) SPI0 or GPIO SPI1 or GPIO *External Address Bus or GPIO 3 (GPIOC8 - 10) GPIO *External Data Bus D7 - D10 (GPIOF0 - 3) 6 4 3 4 PWMB0 - 5 ISB0 - 2 (GPIOD10 - 12) FAULTB0-3 ANA0 - 7 VREF ANB0 - 7 ADCA ADCB PWMB *External Bus Control GPIOD0 - 5 (CS2 - 7) 8 6 5 8 SCI0 or GPIOE SCI1 or GPIO TXD0 (GPIOE0) RXD0 (GPIOE1) TXD1 (GPIOD6) RXD1 (GPIOD7) TCK TMS TDI TDO TRST 1 1 1 1 1 1 1 1 1 1 1 1 1 IRQA IRQB RESET RSTO Interrupt/ Program Control 2 4 TC0 - 1 (GPIOE8 - 9) (GPIOE10 - 13) QUAD Timer C or GPIO JTAG/ EOnCE Port * EMI not functional in this package; use as GPIO pins Figure 2-2 56F8135 Signals Identified by Functional Group1 (128-Pin LQFP) 1. Alternate pin functionality is shown in parenthesis; pin direction/type shown is the default functionality. 56F8335 Technical Data, Rev. 5 16 Freescale Semiconductor Preliminary Signal Pins 2.2 Signal Pins After reset, each pin is configured for its primary function (listed first). Any alternate functionality must be programmed. EMI is not functional in this package; since only part of the address/data bus is bonded out, use as GPIO pins. Note: Signals in italics are NOT available in the 56F8135 device. If the “State During Reset” lists more than one state for a pin, the first state is the actual reset state. Other states show the reset condition of the alternate function, which you get if the alternate pin function is selected without changing the configuration of the alternate peripheral. For example, the A8/GPIOA0 pin shows that it is tri-stated during reset. If the GPIOA_PER is changed to select the GPIO function of the pin, it will become an input if no other registers are changed. Table 2-2 Signal and Package Information for the 128-Pin LQFP Signal Name VDD_IO VDD_IO VDD_IO VDD_IO VDD_IO VDD_IO VDD_IO VDDA_ADC VDDA_OSC_ PLL Pin No. Type State During Reset Signal Description 4 14 25 36 62 76 112 94 72 Supply I/O Power — This pin supplies 3.3V power to the chip I/O interface and also the Processor core throught the on-chip voltage regulator, if it is enabled. Supply Supply ADC Power — This pin supplies 3.3V power to the ADC modules. It must be connected to a clean analog power supply. Oscillator and PLL Power — This pin supplies 3.3V power to the OSC and to the internal regulator that in turn supplies the Phase Locked Loop. It must be connected to a clean analog power supply. Ground — These pins provide ground for chip logic and I/O drivers. VSS VSS VSS VSS VSS 3 21 35 59 65 Supply 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 17 Table 2-2 Signal and Package Information for the 128-Pin LQFP (Continued) Signal Name VSSA_ADC OCR_DIS Pin No. Type State During Reset Signal Description 95 71 Supply Input Input ADC Analog Ground — This pin supplies an analog ground to the ADC modules. On-Chip Regulator Disable — Tie this pin to VSS to enable the on-chip regulator Tie this pin to VDD to disable the on-chip regulator This pin is intended to be a static DC signal from power-up to shut down. Do not try to toggle this pin for power savings during operation. VCAP1 VCAP2 VCAP3 VCAP4 49 122 75 13 Supply Supply VCAP1 - 4 — When OCR_DIS is tied to VSS (regulator enabled), connect each pin to a 2.2μF or greater bypass capacitor in order to bypass the core logic voltage regulator, required for proper chip operation. When OCR_DIS is tied to VDD (regulator disabled), these pins become VDD_CORE and should be connected to a regulated 2.5V power supply. Note: This bypass is required even if the chip is powered with an external supply. VPP1 VPP2 CLKMODE 119 5 79 Input Input VPP1 - 2 — These pins should be left unconnected as an open circuit for normal functionality. Clock Input Mode Selection — This input determines the function of the XTAL and EXTAL pins. 1 = External clock input on XTAL is used to directly drive the input clock of the chip. The EXTAL pin should be grounded. 0 = A crystal or ceramic resonator should be connected between XTAL and EXTAL. Input Input EXTAL 74 Input Input External Crystal Oscillator Input — This input can be connected to an 8MHz external crystal. Tie this pin low if XTAL is driven by an external clock source. Crystal Oscillator Output — This output connects the internal crystal oscillator output to an external crystal. If an external clock is used, XTAL must be used as the input and EXTAL connected to GND. The input clock can be selected to provide the clock directly to the core. This input clock can also be selected as the input clock for the on-chip PLL. XTAL 73 Input/ Output Chip-driven 56F8335 Technical Data, Rev. 5 18 Freescale Semiconductor Preliminary Signal Pins Table 2-2 Signal and Package Information for the 128-Pin LQFP (Continued) Signal Name CLKO Pin No. Type State During Reset In reset, output is disabled Signal Description 6 Output Clock Output — This pin outputs a buffered clock signal. Using the SIM CLKO Select Register (SIM_CLKOSR), this pin can be programmed as any of the following: disabled, CLK_MSTR (system clock), IPBus clock, oscillator output, prescaler clock and postscaler clock. Other signals are also available for test purposes. See Part 6.5.7 for details. A8 15 Output In reset, output is disabled, pull-up is enabled Address Bus — A8 - A13 specify six of the address lines for external program or data memory accesses. Depending upon the state of the DRV bit in the EMI bus control register (BCR), A8 A13 and EMI control signals are tri-stated when the external bus is inactive. Port A GPIO — These six GPIO pins can be individually programmed as input or output pins. After reset, these pins default to address bus functionality and must be programmed as GPIO. To deactivate the internal pull-up resistor, clear the appropriate GPIO bit in the GPIOA_PUR register. Example: GPIOA0, clear bit 0 in the GPIOA_PUR register. (GPIOA0) A9 (GPIOA1) A10 (GPIOA2) A11 (GPIOA3) A12 (GPIOA4) A13 (GPIOA5) GPIOB0 16 17 18 19 20 27 Schmitt Input/ Output Note: Primary function is not available in this package configuration; GPIO function must be used instead. Schmitt Input/ Output Output Input, pull-up enabled Port B GPIO — These four GPIO pins can be individually programmed as an input or output pin. (A16) GPIOB1 (A17) GPIOB2 (A18) GPIOB3 (A19) 30 29 28 Address Bus — A16 - A19 specify four of the address lines for external program or data memory accesses. Depending upon the state of the DRV bit in the EMI bus control register (BCR), A16 A19 and EMI control signals are tri-stated when the external bus is inactive. After reset, the default state is GPIO. To deactivate the internal pull-up resistor, clear bit 0 in the GPIOB_PUR register. Example: GPIOB1, clear bit 1 in the GPIOB_PUR register. 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 19 Table 2-2 Signal and Package Information for the 128-Pin LQFP (Continued) Signal Name GPIOB4 Pin No. Type State During Reset Input, pull-up enabled Signal Description 31 Schmitt Input/ Output Output Port B GPIO — This GPIO pin can be individually programmed as an input or output pin. (A20) Address Bus — A20 specifies one of the address lines for external program or data memory accesses. Depending upon the state of the DRV bit in the EMI bus control register (BCR), A20 and EMI control signals are tri-stated when the external bus is inactive. Clock Output — can be used to monitor the prescaler_clock on GPIOB4. After reset, the default state is GPIO. This pin can also be used to view the prescaler_clock. In these cases, the GPIOB_PER can be used to disable the GPIO. The CLKOSR register in the SIM can then be used to choose between address and clock functions; see Part 6.5.7 for details. To deactivate the internal pull-up resistor, clear bit 4 in the GPIOB_PUR register. (prescaler_ clock) Output D7 22 Input/ Output In reset, output is disabled, pull-up is enabled Data Bus — D7 - D10 specify part of the data for external program or data memory accesses. Depending upon the state of the DRV bit in the EMI bus control register (BCR), D7 - D10 are tri-stated when the external bus is inactive Port F GPIO — These four GPIO pins can be individually programmed as input or output pins. After reset, these pins default to data bus functionality and should be programmed as GPIO. To deactivate the internal pull-up resistor, clear the appropriate GPIO bit in the GPIOF_PUR register. Example: GPIOF0, clear bit 0 in the GPIOF_PUR register. Note: Primary function is not available in this package configuration; GPIO function must be used instead. (GPIOF0) D8 (GPIOF1) D9 (GPIOF2) D10 (GPIOF3) 23 24 26 Input/ Output 56F8335 Technical Data, Rev. 5 20 Freescale Semiconductor Preliminary Signal Pins Table 2-2 Signal and Package Information for the 128-Pin LQFP (Continued) Signal Name GPIOD0 Pin No. Type State During Reset Input, pull-up enabled Signal Description 42 Input/ Output Output Port D GPIO — These six GPIO pins can be individually programmed as input or output pins. Chip Select — CS2 - CS7 may be programmed within the EMI module to act as chip selects for specific areas of the external memory map. Depending upon the state of the DRV bit in the EMI bus control register (BCR), CS2 - CS7 are tri-stated when the external bus is inactive. After reset, these pins are configured as GPIO. (CS2) GPIOD1 (CS3) GPIOD2 (CS4) GPIOD3 (CS5) GPIOD4 (CS6) GPIOD5 (CS7) TXD0 (GPIOE0) 43 44 45 46 47 7 To deactivate the internal pull-up resistor, clear the appropriate GPIO bit in the GPIOD_PUR register. Example: GPIOD0, clear bit 0 in the GPIOD_PUR register. Output Input/ Output In reset, output is disabled, pull-up is enabled Transmit Data — SCI0 transmit data output Port E GPIO — This GPIO pin can be individually programmed as an input or output pin. After reset, the default state is SCI output. To deactivate the internal pull-up resistor, clear bit 0 in the GPIOE_PUR register. RXD0 (GPIOE1) 8 Input Input/ Output Input, pull-up enabled Receive Data — SCI0 receive data input Port E GPIO — This GPIO pin can be individually programmed as an input or output pin. After reset, the default state is SCI output. To deactivate the internal pull-up resistor, clear bit 1 in the GPIOE_PUR register. TXD1 (GPIOD6) 40 Output Input/ Output In reset, output is disabled, pull-up is enabled Transmit Data — SCI1 transmit data output Port D GPIO — This GPIO pin can be individually programmed as an input or output pin. After reset, the default state is SCI output. To deactivate the internal pull-up resistor, clear bit 6 in the GPIOD_PUR register. 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 21 Table 2-2 Signal and Package Information for the 128-Pin LQFP (Continued) Signal Name RXD1 (GPIOD7) Pin No. Type State During Reset Input, pull-up enabled Signal Description 41 Input Input/ Output Receive Data — SCI1 receive data input Port D GPIO — This GPIO pin can be individually programmed as an input or output pin. After reset, the default state is SCI input. To deactivate the internal pull-up resistor, clear bit 7 in the GPIOD_PUR register. TCK 115 Schmitt Input Input, pulled low internally Input, pulled high internally Test Clock Input — This input pin provides a gated clock to synchronize the test logic and shift serial data to the JTAG/EOnCE port. The pin is connected internally to a pull-down resistor. Test Mode Select Input — This input pin is used to sequence the JTAG TAP controller’s state machine. It is sampled on the rising edge of TCK and has an on-chip pull-up resistor. To deactivate the internal pull-up resistor, set the JTAG bit in the SIM_PUDR register. Note: Always tie the TMS pin to VDD through a 2.2K resistor. TMS 116 Schmitt Input TDI 117 Schmitt Input Input, pulled high internally Test Data Input — This input pin provides a serial input data stream to the JTAG/EOnCE port. It is sampled on the rising edge of TCK and has an on-chip pull-up resistor. To deactivate the internal pull-up resistor, set the JTAG bit in the SIM_PUDR register. TDO 118 Output In reset, output is disabled, pull-up is enabled Test Data Output — This tri-stateable output pin provides a serial output data stream from the JTAG/EOnCE port. It is driven in the shift-IR and shift-DR controller states, and changes on the falling edge of TCK. 56F8335 Technical Data, Rev. 5 22 Freescale Semiconductor Preliminary Signal Pins Table 2-2 Signal and Package Information for the 128-Pin LQFP (Continued) Signal Name TRST Pin No. Type State During Reset Input, pulled high internally Signal Description 114 Schmitt Input Test Reset — As an input, a low signal on this pin provides a reset signal to the JTAG TAP controller. To ensure complete hardware reset, TRST should be asserted whenever RESET is asserted. The only exception occurs in a debugging environment when a hardware device reset is required and the JTAG/EOnCE module must not be reset. In this case, assert RESET, but do not assert TRST. To deactivate the internal pull-up resistor, set the JTAG bit in the SIM_PUDR register. Note: For normal operation, connect TRST directly to VSS. If the design is to be used in a debugging environment, TRST may be tied to VSS through a 1K resistor. PHASEA0 127 Schmitt Input Schmitt Input/ Output Schmitt Input/ Output Input, pull-up enabled Phase A — Quadrature Decoder 0, PHASEA input (TA0) TA0 — Timer A, Channel 0 (GPIOC4) Port C GPIO — This GPIO pin can be individually programmed as an input or output pin. After reset, the default state is PHASEA0. To deactivate the internal pull-up resistor, clear bit 4 of the GPIOC_PUR register. PHASEB0 128 Schmitt Input Schmitt Input/ Output Schmitt Input/ Output Input, pull-up enabled Phase B — Quadrature Decoder 0, PHASEB input (TA1) TA1 — Timer A, Channel 1 (GPIOC5) Port C GPIO — This GPIO pin can be individually programmed as an input or output pin. After reset, the default state is PHASEB0. To deactivate the internal pull-up resistor, clear bit 5 of the GPIOC_PUR register. 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 23 Table 2-2 Signal and Package Information for the 128-Pin LQFP (Continued) Signal Name INDEX0 Pin No. Type State During Reset Input, pull-up enabled Signal Description 1 Schmitt Input Schmitt Input/ Output Schmitt Input/ Output Index — Quadrature Decoder 0, INDEX input (TA2) TA2 — Timer A, Channel 2 (GPIOC6) Port C GPIO — This GPIO pin can be individually programmed as an input or output pin. After reset, the default state is INDEX0. To deactivate the internal pull-up resistor, clear bit 6 of the GPIOC_PUR register. HOME0 2 Schmitt Input Schmitt Input/ Output Schmitt Input/ Output Input, pull-up enabled Home — Quadrature Decoder 0, HOME input (TA3) TA3 — Timer A ,Channel 3 (GPIOC7) Port C GPIO — This GPIO pin can be individually programmed as an input or output pin. After reset, the default state is HOME0. To deactivate the internal pull-up resistor, clear bit 7 of the GPIOC_PUR register. SCLK0 124 Schmitt Input/ Output Schmitt Input/ Output Input, pull-up enabled SPI 0 Serial Clock — In the master mode, this pin serves as an output, clocking slaved listeners. In slave mode, this pin serves as the data clock input. Port E GPIO — This GPIO pin can be individually programmed as an input or output pin. After reset, the default state is SCLK0. To deactivate the internal pull-up resistor, clear bit 4 in the GPIOE_PUR register. (GPIOE4) 56F8335 Technical Data, Rev. 5 24 Freescale Semiconductor Preliminary Signal Pins Table 2-2 Signal and Package Information for the 128-Pin LQFP (Continued) Signal Name MOSI0 Pin No. Type State During Reset In reset, output is disabled, pull-up is enabled Signal Description 126 Input/ Output SPI 0 Master Out/Slave In — This serial data pin is an output from a master device and an input to a slave device. The master device places data on the MOSI line a half-cycle before the clock edge the slave device uses to latch the data. Port E GPIO — This GPIO pin can be individually programmed as an input or output pin. After reset, the default state is MOSI0. To deactivate the internal pull-up resistor, clear bit 5 in the GPIOE_PUR register. (GPIOE5) Input/ Output MISO0 125 Input/ Output Input, pull-up enabled SPI 0 Master In/Slave Out — This serial data pin is an input to a master device and an output from a slave device. The MISO line of a slave device is placed in the high-impedance state if the slave device is not selected. The slave device places data on the MISO line a half-cycle before the clock edge the master device uses to latch the data. Port E GPIO — This GPIO pin can be individually programmed as an input or output pin. After reset, the default state is MISO0. To deactivate the internal pull-up resistor, clear bit 6 in the GPIOE_PUR register. (GPIOE6) Input/ Output SS0 123 Input Input, pull-up enabled SPI 0 Slave Select — SS0 is used in slave mode to indicate to the SPI module that the current transfer is to be received. Port E GPIO — This GPIO pin can be individually programmed as an input or output pin. After reset, the default state is SS0. To deactivate the internal pull-up resistor, clear bit 7 in the GPIOE_PUR register. (GPIOE7) Input/ Output 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 25 Table 2-2 Signal and Package Information for the 128-Pin LQFP (Continued) Signal Name PHASEA1 (TB0) Schmitt Input/ Output (SCLK1) Schmitt Input/ Output SPI 1 Serial Clock — In the master mode, this pin serves as an output, clocking slaved listeners. In slave mode, this pin serves as the data clock input. To activate the SPI function, set the PHSA_ALT bit in the SIM_GPS register. For details, see Part 6.5.8. Port C GPIO — This GPIO pin can be individually programmed as an input or output pin. In the 56F8335, the default state after reset is PHASEA1. In the 56F8135, the default state is not one of the functions offered and must be reconfigured. To deactivate the internal pull-up resistor, clear bit 0 in the GPIOC_PUR register. PHASEB1 10 Schmitt Input Schmitt Input/ Output Schmitt Input/ Output Input, pull-up enabled Phase B1 — Quadrature Decoder 1, PHASEB input for decoder 1. TB1 — Timer B, Channel 1 Pin No. Type State During Reset Input, pull-up enabled Signal Description 9 Schmitt Input Phase A1 — Quadrature Decoder 1, PHASEA input for decoder 1. TB0 — Timer B, Channel 0 (GPIOC0) Schmitt Input/ Output (TB1) (MOSI1) SPI 1 Master Out/Slave In — This serial data pin is an output from a master device and an input to a slave device. The master device places data on the MOSI line a half-cycle before the clock edge the slave device uses to latch the data. To activate the SPI function, set the PHSB_ALT bit in the SIM_GPS register. For details, see Part 6.5.8. Port C GPIO — This GPIO pin can be individually programmed as an input or output pin. In the 56F8335, the default state after reset is PHASEB1. In the 56F8135, the default state is not one of the functions offered and must be reconfigured. To deactivate the internal pull-up resistor, clear bit 1 in the GPIOC_PUR register. (GPIOC1) Schmitt Input/ Output 56F8335 Technical Data, Rev. 5 26 Freescale Semiconductor Preliminary Signal Pins Table 2-2 Signal and Package Information for the 128-Pin LQFP (Continued) Signal Name INDEX1 Pin No. Type State During Reset Input, pull-up enabled Signal Description 11 Schmitt Input Schmitt Input/ Output Schmitt Input/ Output Index1 — Quadrature Decoder 1, INDEX input (TB2) TB2 — Timer B, Channel 2 (MISO1) SPI 1 Master In/Slave Out — This serial data pin is an input to a master device and output from a slave device. The MISO line of a slave device is placed in the high-impedance state if the slave device is not selected. The slave device places data on the MISO line a half-cycle before the clock edge the master device uses to latch the data. To activate the SPI function, set the INDEX_ALT bit in the SIM_GPS register. See Part 6.5.8 for details. Port C GPIO — This GPIO pin can be individually programmed as an input or output pin. In the 56F8335, the default state after reset is INDEX1. In the 56F8135, the default state is not one of the functions offered and must be reconfigured. To deactivate the internal pull-up resistor, clear bit 2 in the GPIOC_PUR register. (GPIOC2) Schmitt Input/ Output HOME1 12 Schmitt Input Schmitt Input/ Output Schmitt Input Input, pull-up enabled Home — Quadrature Decoder 1, HOME input (TB3) TB3 — Timer B, Channel 3 (SS1) SPI 1 Slave Select — In the master mode, this pin is used to arbitrate multiple masters. In slave mode, this pin is used to select the slave. To activate the SPI function, set the HOME_ALT bit in the SIM_GPS register. See Part 6.5.8 for details. Port C GPIO — This GPIO pin can be individually programmed as input or output pin. In the 56F8335, the default state after reset is HOME1. In the 56F8135, the default state is not one of the functions offered and must be reconfigured. To deactivate the internal pull-up resistor, clear bit 3 in the GPIOC_PUR register. (GPIOC3) Schmitt Input/ Output 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 27 Table 2-2 Signal and Package Information for the 128-Pin LQFP (Continued) Signal Name PWMA0 PWMA1 PWMA2 PWMA3 PWMA4 PWMA5 ISA0 Pin No. Type State During Reset In reset, output is disabled, pull-up is enabled Signal Description 58 60 61 63 64 66 104 Output PWMA0 - 5 — These are six PWMA output pins. Schmitt Input Input, pull-up enabled ISA0 - 2 — These three input current status pins are used for top/bottom pulse width correction in complementary channel operation for PWMA. Port C GPIO — These GPIO pins can be individually programmed as input or output pins. In the 56F8335, these pins default to ISA functionality. (GPIOC8) ISA1 (GPIOC9) ISA2 (GPIOC10) 106 105 Schmitt Input/ Output In the 56F8135, the default state is not one of the functions offered and must be reconfigured. To deactivate the internal pull-up resistor, clear the appropriate bit of the GPIOC_PUR register. See Part 6.5.6 for details. FAULTA0 FAULTA1 FAULTA2 67 68 69 Schmitt Input Input, pull-up enabled FAULTA0 - 2 — These three fault input pins are used for disabling selected PWMA outputs in cases where fault conditions originate off-chip. To deactivate the internal pull-up resistor, set the PWMA0 bit in the SIM_PUDR register. See Part 6.5.6 for details. FAULTA3 70 Schmitt Input Input, pull-up enabled FAULTA3 — This fault input pin is used for disabling selected PWMA outputs in cases where fault conditions originate off-chip. To deactivate the internal pull-up resistor, set the PWMA1 bit in the SIM_PUDR register. See Part 6.5.6 for details. PWMB0 PWMB1 PWMB2 PWMB3 PWMB4 PWMB5 32 33 34 37 38 39 Output In reset, output is disabled, pull-up is enabled PWMB0 - 5 — Six PWMB output pins. 56F8335 Technical Data, Rev. 5 28 Freescale Semiconductor Preliminary Signal Pins Table 2-2 Signal and Package Information for the 128-Pin LQFP (Continued) Signal Name ISB0 Pin No. Type State During Reset Input, pull-up enabled Signal Description 48 Schmitt Input ISB0 - 2 — These three input current status pins are used for top/bottom pulse width correction in complementary channel operation for PWMB. Port D GPIO — These GPIO pins can be individually programmed as input or output pins. At reset, these pins default to ISB functionality. (GPIOD10) ISB1 (GPIOD11) ISB2 (GPIOD12) FAULTB0 FAULTB1 FAULTB2 FAULTB3 ANA0 ANA1 ANA2 ANA3 ANA4 ANA5 ANA6 ANA7 VREFH VREFP VREFMID VREFN VREFLO 50 51 Schmitt Input/ Output To deactivate the internal pull-up resistor, clear the appropriate bit of the GPIOD_PUR register. See Part 6.5.6 for details. Schmitt Input Input, pull-up enabled FAULTB0 - 3 — These four fault input pins are used for disabling selected PWMB outputs in cases where fault conditions originate off-chip. To deactivate the internal pull-up resistor, set the PWMB bit in the SIM_PUDR register. See Part 6.5.6 for details. Input Analog Input ANA0 - 3 — Analog inputs to ADC A, channel 0 54 55 56 57 80 81 82 83 84 85 86 87 93 Input Analog Input ANA4 - 7 — Analog inputs to ADC A, channel 1 Input Analog Input Analog Input/ Output VREFH — Analog Reference Voltage High. VREFH must be less than or equal to VDDA_ADC. VREFP, VREFMID & VREFN — Internal pins for voltage reference which are brought off-chip so that they can be bypassed. Connect to a 0.1 μF low ESR capacitor. 92 91 90 89 Input/ Output Input Analog Input VREFLO — Analog Reference Voltage Low. This should normally be connected to a low-noise VSSA. 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 29 Table 2-2 Signal and Package Information for the 128-Pin LQFP (Continued) Signal Name ANB0 ANB1 ANB2 ANB3 ANB4 ANB5 ANB6 ANB7 TEMP_ SENSE Pin No. Type State During Reset Analog Input Signal Description 96 97 98 99 100 101 102 103 88 Input ANB0 - 3 — Analog inputs to ADC B, channel 0 Input Analog Input ANB4 - 7 — Analog inputs to ADC B, channel 1 Output Analog Output Temperature Sense Diode — This signal connects to an on-chip diode that can be connected to one of the ADC inputs and is used to monitor the temperature of the die. Must be bypassed with a 0.01 μF capacitor. FlexCAN Receive Data — This is the CAN input. This pin has an internal pull-up resistor. To deactivate the internal pull-up resistor, set the CAN bit in the SIM_PUDR register. CAN_RX 121 Schmitt Input Input, pull-up enabled CAN_TX 120 Open Drain Output Open Drain Output FlexCAN Transmit Data — CAN output with internal pull-up enable at reset.* * Note: If a pin is configured as open drain output mode, internal pull-up will automatically be disabled when it outputs low. Internal pull-up will be enabled unless it has been manually disabled by clearing the corresponding bit in the PUREN register of the GPIO module, when it outputs high. If a pin is configured as push-pull output mode, internal pull-up will automatically be disabled, whether it outputs low or high. TC0 111 Schmitt Input/ Output Schmitt Input/ Output Input, pull-up enabled TC0 - 1 — Timer C, Channels 0 and 1 (GPIOE8) TC1 (GPIOE9) 113 Port E GPIO — These GPIO pins can be individually programmed as input or output pins. At reset, these pins default to Timer functionality. To deactivate the internal pull-up resistor, clear the appropriate bit of the GPIOE_PUR register. See Part 6.5.6 for details. 56F8335 Technical Data, Rev. 5 30 Freescale Semiconductor Preliminary Signal Pins Table 2-2 Signal and Package Information for the 128-Pin LQFP (Continued) Signal Name TD0 Pin No. Type State During Reset Input, pull-up enabled Signal Description 107 Schmitt Input/ Output Schmitt Input/ Output TD0 - TD3 — Timer D, Channels 0, 1, 2 and 3 (GPIOE10) TD1 (GPIOE11) TD2 (GPIOE12) TD3 (GPIOE13) IRQA IRQB 108 109 110 52 53 Schmitt Input Input, pull-up enabled Port E GPIO — These GPIO pins can be individually programmed as input or output pins. At reset, these pins default to Timer functionality. To deactivate the internal pull-up resistor, clear the appropriate bit of the GPIOE_PUR register. See Part 6.5.6 for details. External Interrupt Request A and B — The IRQA and IRQB inputs are asynchronous external interrupt requests during Stop and Wait mode operation. During other operating modes, they are synchronized external interrupt requests, which indicate an external device is requesting service. They can be programmed to be level-sensitive or negative-edge triggered. To deactivate the internal pull-up resistor, set the IRQ bit in the SIM_PUDR register. See Part 6.5.6 for details. RESET 78 Schmitt Input Input, pull-up enabled Reset — This input is a direct hardware reset on the processor. When RESET is asserted low, the device is initialized and placed in the reset state. A Schmitt trigger input is used for noise immunity. The internal reset signal will be deasserted synchronous with the internal clocks after a fixed number of internal clocks. To ensure complete hardware reset, RESET and TRST should be asserted together. The only exception occurs in a debugging environment when a hardware device reset is required and the JTAG/EOnCE module must not be reset. In this case, assert RESET, but do not assert TRST. Note: The internal Power-On Reset will assert on initial power-up. To deactivate the internal pull-up resistor, set the RESET bit in the SIM_PUDR register. See Part 6.5.6. for details. RSTO 77 Output Output Reset Output — This output reflects the internal reset state of the chip. 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 31 Table 2-2 Signal and Package Information for the 128-Pin LQFP (Continued) Signal Name EXTBOOT Pin No. Type State During Reset Input, pull-up enabled Signal Description Internal Ground Schmitt Input External Boot — This input is tied to VDD to force the device to boot from off-chip memory (assuming that the on-chip Flash memory is not in a secure state). Otherwise, it is tied to ground. For details, see Table 4-4. Note: When this pin is tied low, the customer boot software should disable the internal pull-up resistor by setting the XBOOT bit of the SIM_PUDR; see Part 6.5.6. Note: This pin is internally tied low (to VSS). EMI_MODE Internal Ground Schmitt Input Input, pull-up enabled External Memory Mode — This device will boot from internal Flash memory under normal operation. This function is also affected by EXTBOOT and the Flash security mode; see Table 4-4 for details. Note: When this pin is tied low, the customer boot software should disable the internal pull-up resistor by setting the EMI_MODE bit of the SIM_PUDR; see Part 6.5.6. Note: This pin is internally tied low (to VSS). 56F8335 Technical Data, Rev. 5 32 Freescale Semiconductor Preliminary Introduction Part 3 On-Chip Clock Synthesis (OCCS) 3.1 Introduction Refer to the OCCS chapter of the 56F8300 Peripheral User Manual for a full description of the OCCS. The material contained here identifies the specific features of the OCCS design. Figure 3-1 shows the specific OCCS block diagram to reference in the OCCS chapter of the 56F8300 Peripheral User Manual. CLKMODE XTAL MUX Crystal OSC EXTAL ZSRC Prescaler CLK PLLDB FREF PLL FOUT x (1 to 128) FEEDBACK PLLCID PLLCOD Prescaler ÷ (1,2,4,8) MSTR_OSC ÷2 FOUT/2 Postscaler ÷ (1,2,4,8) Postscaler CLK MUX SYS_CLK2 Source to SIM Bus Interface & Control Bus Interface Lock Detector Loss of Reference Clock Detector LCK Loss of Reference Clock Interrupt Figure 3-1 OCCS Block Diagram 3.2 External Clock Operation The system clock can be derived from an external crystal, ceramic resonator, or an external system clock signal. To generate a reference frequency using the internal oscillator, a reference crystal or ceramic resonator must be connected between the EXTAL and XTAL pins. 3.2.1 Crystal Oscillator The internal oscillator is designed to interface with a parallel-resonant crystal resonator in the frequency range specified for the external crystal in Table 10-15. A recommended crystal oscillator circuit is shown in Figure 3-2. Follow the crystal supplier’s recommendations when selecting a crystal, since crystal parameters determine the component values required to provide maximum stability and reliable start-up. The crystal and associated components should be mounted as near as possible to the EXTAL and XTAL 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 33 pins to minimize output distortion and start-up stabilization time. Crystal Frequency = 4 - 8MHz (optimized for 8MHz) EXTAL RZ CLKMODE = 0 XTAL EXTAL RZ XTAL Sample External Crystal Parameters: Rz = 750 KΩ Note: If the operating temperature range is limited to below 85oC (105oC junction), then Rz = 10 Meg Ω CL2 CL1 Figure 3-2 Connecting to a Crystal Oscillator Note: The OCCS_COHL bit must be set to 1 when a crystal oscillator is used. The reset condition on the OCCS_COHL bit is 0. Please see the COHL bit in the Oscillator Control (OSCTL) register, discussed in the 56F8300 Peripheral User’s Manual. 3.2.2 Ceramic Resonator (Default) It is also possible to drive the internal oscillator with a ceramic resonator, assuming the overall system design can tolerate the reduced signal integrity. A typical ceramic resonator circuit is shown in Figure 3-3. Refer to the supplier’s recommendations when selecting a ceramic resonator and associated components. The resonator and components should be mounted as near as possible to the EXTAL and XTAL pins. Resonator Frequency = 4 - 8MHz (optimized for 8MHz) 2 Terminal 3 Terminal EXTAL XTAL Rz EXTAL XTAL Rz Sample External Ceramic Resonator Parameters: Rz = 750 KΩ CL1 CL2 CLKMODE = 0 C1 C2 Figure 3-3 Connecting a Ceramic Resonator Note: The OCCS_COHL bit must be set to 0 when a ceramic resonator is used. The reset condition on the OCCS_COHL bit is 0. Please see the COHL bit in the Oscillator Control (OSCTL) register, discussed in the 56F8300 Peripheral User’s Manual. 3.2.3 External Clock Source The recommended method of connecting an external clock is illustrated in Figure 3-4. The external clock source is connected to XTAL and the EXTAL pin is grounded. Set OCCS_COHL bit high when using an external clock source as well. 56F8335 Technical Data, Rev. 5 34 Freescale Semiconductor Preliminary Registers XTAL External Clock EXTAL VSS Note: When using an external clocking source with this configuration, the input “CLKMODE” should be high and COHL bit in the OSCTL register should be set to 1. Figure 3-4 Connecting an External Clock Signal Register 3.3 Registers When referring to the register definitions for the OCCS in the 56F8300 Peripheral User Manual, use the register definitions without the internal Relaxation Oscillator, since the 56F8335/56F8135 devices do NOT contain this oscillator. Part 4 Memory Map 4.1 Introduction The 56F8335 and 56F8135 devices are 16-bit motor-control chips based on the 56800E core. These parts use a Harvard-style architecture with two independent memory spaces for Data and Program. On-chip RAM and Flash memories are used in both spaces. This section provides memory maps for: • • Program Address Space, including the Interrupt Vector Table Data Address Space, including the EOnCE Memory and Peripheral Memory Maps On-chip memory sizes for each device are summarized in Table 4-1. Flash memories’ restrictions are identified in the “Use Restrictions” column of Table 4-1. Note: Data Flash and Program RAM are NOT available on the 56F8135 device. Table 4-1 Chip Memory Configurations On-Chip Memory Program Flash 56F8335 64KB 56F8135 64KB Use Restrictions Erase / Program via Flash interface unit and word writes to CDBW 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 35 Table 4-1 Chip Memory Configurations On-Chip Memory Data Flash 56F8335 8KB 56F8135 — Use Restrictions Erase / Program via Flash interface unit and word writes to CDBW. Data Flash can be read via either CDBR or XDB2, but not by both simultaneously None None Erase / Program via Flash Interface unit and word writes to CDBW Program RAM Data RAM Program Boot Flash 4KB 8KB 8KB — 8KB 8KB 4.2 Program Map The Program memory map is located in Table 4-4. The operating mode control bits (MA and MB) in the Operating Mode Register (OMR) control the Program memory map. At reset, these bits are set as indicated in Table 4-2. EXT_BOOT = EMI_MODE = 0 and cannot be changed in the 56F8335 or 56F8135. Table 4-2 OMR MB/MA Value at Reset1 OMR MB = Flash Secured State2,3 0 0 1 1 OMR MA = EXTBOOT Pin 0 1 0 1 Chip Operating Mode Mode 0 – Internal Boot; EMI is configured to use 16 address lines; Flash Memory is secured; external P-space is not allowed; the EOnCE is disabled Not valid; cannot boot externally if the Flash is secured and will actually configure to 00 state Mode 0 – Internal Boot; EMI is configured to use 16 address lines Mode 1 – External Boot; Flash Memory is not secured; EMI configuration is determined by the state of the EMI_MODE pin 1. Information in shaded areas not applicable to 56F8335/56F8135. 2. This bit is only configured at reset. If the Flash secured state changes, this will not be reflected in MB until the next reset. 3. Changing MB in software will not affect Flash memory security. After reset, the OMR MA bit can be changed and will have an effect on the P-space memory map, as shown in Table 4-3. Changing the OMR MB bit will have no effect. Table 4-3 Changing OMR MA Value During Normal Operation OMR MA 0 11 Chip Operating Mode Use internal P-space memory map configuration Use external P-space memory map configuration – If MB = 0 at reset, changing this bit has no effect. 56F8335 Technical Data, Rev. 5 36 Freescale Semiconductor Preliminary Interrupt Vector Table 1. Setting this bit can cause unpredictable results and is not recommended, since the EMI is not functional in this package. Table 4-4 shows the memory map options of the 56F8335/56F8135. The two right columns cannot be used, since the EMI pins are not provided in the package; therefore, only the Mode 0 column is relevant. Note: Program RAM is NOT available on the 56F8135 device. Table 4-4 Program Memory Map at Reset Mode 0 (MA = 0) Begin/End Address Internal Boot Internal Boot 16-Bit External Address Bus External Program Memory5 Mode 11 (MA = 1) External Boot EMI_MODE = 02, 3 16-Bit External Address Bus External Program Memory5 EMI_MODE = 14 20-Bit External Address Bus External Program Memory5 External Program RAM5 COP Reset Address = 02 0002 Boot Location = 02 0000 P:$1F FFFF P:$10 0000 P:$0F FFFF P:$03 0000 P:$02 FFFF P:$02 F800 P:$02 F7FF P:$02 1000 P:$02 0FFF P:$02 0000 On-Chip Program RAM 4KB On-Chip Program RAM 4KB Reserved 116KB Boot Flash 8KB COP Reset Address = 02 0002 Boot Location = 02 0000 External Program RAM5 Boot Flash 8KB (Not Used for Boot in this Mode) Reserved 64KB Internal Program Flash 64KB P:$01 FFFF P:$01 8000 P:$01 7FFF P:$01 0000 P:$00 FFFF P:$00 8000 P:$00 7FFF P:$00 0000 Reserved 64KB Internal Program Flash 64KB External Program RAM5 COP Reset Address = 00 0002 Boot Location = 00 0000 1. Cannot be used since MA = EXTBOOT = 0 and the EMI is not available; information in shaded areas not applicable to 56F8335/56F8135. 2. This mode provides maximum compatibility with 56F80x parts while operating externally. 3. “EMI_MODE = 0”, EMI_MODE pin is tied to ground at boot up. 4. “EMI_MODE = 1”, EMI_MODE pin is tied to VDD at boot up. 5. Not accessible in this part, since the EMI is not fully pinned out in this package; information in shaded areas not applicable to 56F8335/56F8135. 4.3 Interrupt Vector Table Table 4-5 provides the reset and interrupt priority structure, including on-chip peripherals. The table is organized with higher-priority vectors at the top and lower-priority interrupts lower in the table. The priority of an interrupt can be assigned to different levels, as indicated, allowing some control over 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 37 interrupt priorities. All level 3 interrupts will be serviced before level 2, and so on. For a selected priority level, the lowest vector number has the highest priority. The location of the vector table is determined by the Vector Base Address (VBA) register. Please see Part 5.6.11 for the reset value of the VBA. In some configurations, the reset address and COP reset address will correspond to vector 0 and 1 of the interrupt vector table. In these instances, the first two locations in the vector table must contain branch or JMP instructions. All other entries must contain JSR instructions. Note: PWMA, FlexCAN, Quadrature Decoder 1, and Quad Timers B and D are NOT available on the 56F8135 device. Table 4-5 Interrupt Vector Table Contents1 Peripheral Vector Number Priority Level Vector Base Address + Interrupt Function Reserved for Reset Overlay2 Reserved for COP Reset Overlay2 core core core core core core 2 3 4 5 6 7 3 3 3 3 1-3 1-3 P:$04 P:$06 P:$08 P:$0A P:$0C P:$0E Illegal Instruction SW Interrupt 3 HW Stack Overflow Misaligned Long Word Access OnCE Step Counter OnCE Breakpoint Unit 0 Reserved core core core 9 10 11 1-3 1-3 1-3 P:$12 P:$14 P:$16 OnCE Trace Buffer OnCE Transmit Register Empty OnCE Receive Register Full Reserved core core core core core 14 15 16 17 18 2 1 0 0-2 0-2 P:$1C P:$1E P:$20 P:$22 P:$24 SW Interrupt 2 SW Interrupt 1 SW Interrupt 0 IRQA IRQB Reserved LVI PLL FM FM 20 21 22 23 0-2 0-2 0-2 0-2 P:$28 P:$2A P:$2C P:$2E Low Voltage Detector (power sense) PLL FM Access Error Interrupt FM Command Complete 56F8335 Technical Data, Rev. 5 38 Freescale Semiconductor Preliminary Interrupt Vector Table Table 4-5 Interrupt Vector Table Contents1 (Continued) Peripheral FM Vector Number 24 Priority Level 0-2 Vector Base Address + P:$30 Interrupt Function FM Command, data and address Buffers Empty Reserved FLEXCAN FLEXCAN FLEXCAN FLEXCAN GPIOF GPIOE GPIOD GPIOC GPIOB GPIOA 26 27 28 29 30 31 32 33 34 35 0-2 0-2 0-2 0-2 0-2 0-2 0-2 0-2 0-2 0-2 P:$34 P:$36 P:$38 P:$3A P:$3C P:$3E P:$40 P:$42 P:$44 P:$46 FLEXCAN Bus Off FLEXCAN Error FLEXCAN Wake Up FLEXCAN Message Buffer Interrupt GPIO F GPIO E GPIO D GPIO C GPIO B GPIO A Reserved SPI1 SPI1 SPI0 SPI0 SCI1 SCI1 38 39 40 41 42 43 0-2 0-2 0-2 0-2 0-2 0-2 P:$4C P:$4E P:$50 P:$52 P:$54 P:$56 SPI 1 Receiver Full SPI 1 Transmitter Empty SPI 0 Receiver Full SPI 0 Transmitter Empty SCI 1 Transmitter Empty SCI 1 Transmitter Idle Reserved SCI1 SCI1 45 46 0-2 0-2 P:$5A P:$5C SCI 1 Receiver Error SCI 1 Receiver Full 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 39 Table 4-5 Interrupt Vector Table Contents1 (Continued) Peripheral DEC1 DEC1 DEC0 DEC0 Vector Number 47 48 49 50 Priority Level 0-2 0-2 0-2 0-2 Vector Base Address + P:$5E P:$60 P:$62 P:$64 Interrupt Function Quadrature Decoder #1 Home Switch or Watchdog Quadrature Decoder #1 INDEX Pulse Quadrature Decoder #0 Home Switch or Watchdog Quadrature Decoder #0 INDEX Pulse Reserved TMRD TMRD TMRD TMRD TMRC TMRC TMRC TMRC TMRB TMRB TMRB TMRB TMRA TMRA TMRA TMRA SCI0 SCI0 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 0-2 0-2 0-2 0-2 0-2 0-2 0-2 0-2 0-2 0-2 0-2 0-2 0-2 0-2 0-2 0-2 0-2 0-2 P:$68 P:$6A P:$6C P:$6E P:$70 P:$72 P:$74 P:$76 P:$78 P:$7A P:$7C P:$7E P:$80 P:$82 P:$84 P:$86 P:$88 P:$8A Timer D, Channel 0 Timer D, Channel 1 Timer D, Channel 2 Timer D, Channel 3 Timer C, Channel 0 Timer C, Channel 1 Timer C, Channel 2 Timer C, Channel 3 Timer B, Channel 0 Timer B, Channel 1 Timer B, Channel 2 Timer B, Channel 3 Timer A, Channel 0 Timer A, Channel 1 Timer A,Channel 2 Timer A, Channel 3 SCI 0 Transmitter Empty SCI 0 Transmitter Idle Reserved SCI0 SCI0 ADCB ADCA ADCB ADCA PWMB PWMA PWMB 71 72 73 74 75 76 77 78 79 0-2 0-2 0-2 0-2 0-2 0-2 0-2 0-2 0-2 P:$8E P:$90 P:$92 P:$94 P:$96 P:$98 P:$9A P:$9C P:$9E SCI 0 Receiver Error SCI 0 Receiver Full ADC B Conversion Compete / End of Scan ADC A Conversion Complete / End of Scan ADC B Zero Crossing or Limit Error ADC A Zero Crossing or Limit Error Reload PWM B Reload PWM A PWM B Fault 56F8335 Technical Data, Rev. 5 40 Freescale Semiconductor Preliminary Data Map Table 4-5 Interrupt Vector Table Contents1 (Continued) Peripheral PWMA core Vector Number 80 81 Priority Level 0-2 -1 Vector Base Address + P:$A0 P:$A2 PWM A Fault SW Interrupt LP Interrupt Function 1. Two words are allocated for each entry in the vector table. This does not allow the full address range to be referenced from the vector table, providing only 19 bits of address. 2. If the VBA is set to $0200 (or VBA = 0000 for Mode 1, EMI_MODE = 0), the first two locations of the vector table are the chip reset addresses; therefore, these locations are not interrupt vectors. 4.4 Data Map Note: Data Flash is NOT available on the 56F8135 device. Table 4-6 Data Memory Map1, Begin/End Address X:$FF FFFF X:$FF FF00 X:$FF FEFF X:$01 0000 X:$00 FFFF X:$00 F000 X:$00 EFFF X:$00 2000 X:$00 1FFF X:$00 1000 X:$00 0FFF X:$00 0000 EX = 03 EOnCE 256 locations allocated External Memory On-Chip Peripherals 4096 locations allocated External Memory On-Chip Data Flash 8KB On-Chip Data RAM 8KB5 2 EX = 14 EOnCE 256 locations allocated External Memory On-Chip Peripherals 4096 locations allocated External Memory 1. Information in shaded areas not applicable to 56F8335/56F8135. 2. All addresses are 16-bit Word addresses, not byte addresses. 3. In the Operation Mode Register. 4. Setting EX = 1 is not recommended in the 56F8335/56F8135, since the EMI is not functional in this package. 5. The Data RAM is organized as a 2K x 32-bit memory to allow single-cycle, long-word operations. 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 41 4.5 Flash Memory Map Figure 4-1 illustrates the Flash Memory (FM) map on the system bus. The Flash Memory is divided into three functional blocks. The Program and boot memories reside on the Program Memory buses. They are controlled by one set of banked registers. Data Memory Flash resides on the Data Memory buses and is controlled separately by its own set of banked registers. The top nine words of the Program Memory Flash are treated as special memory locations. The content of these words is used to control the operation of the Flash Controller. Because these words are part of the Flash Memory content, their state is maintained during power-down and reset. During chip initialization, the content of these memory locations is loaded into Flash Memory control registers, detailed in the Flash Memory chapter of the 56F8300 Peripheral User Manual. These configuration parameters are located between $00_FFF7 and $00_FFFF. Program Memory BOOT_FLASH_START + $1FFF BOOT_FLASH_START = $02_0000 Data Memory FM_BASE + $14 FM_BASE + $00 8KB Boot Banked Registers Unbanked Registers Reserved DATA_FLASH_START + $0FFF 8KB DATA_FLASH_START + $0000 PROG_FLASH_START + $00_FFFF PROG_FLASH_START + $00_FFF7 PROG_FLASH_START + $00_FFF6 FM_PROG_MEM_TOP = $00_FFFF Configure Field Block 0 Odd Block 0 Even ... BLOCK 0 Odd (2 Bytes) $00_0003 BLOCK 0 Even (2 Bytes) $00_0002 BLOCK 0 Odd (2 Bytes) $00_0001 BLOCK 0 Even (2 Bytes) $00_0000 Note: Data Flash is NOT available in the 56F8135 device. 64KB PROG_FLASH_START = $00_0000 Figure 4-1 Flash Array Memory Maps Table 4-7 shows the page and sector sizes used within each Flash memory block on the chip. Note: Data Flash is NOT available on the 56F8135 device. Table 4-7. Flash Memory Partitions Flash Size Program Flash 64KB Sectors 16 Sector Size 2K x 16 bits Page Size 512 x 16 bits 56F8335 Technical Data, Rev. 5 42 Freescale Semiconductor Preliminary EOnCE Memory Map Table 4-7. Flash Memory Partitions Flash Size Data Flash Data Flash Boot Flash 8KB 8KB Sectors 16 4 Sector Size 256 x 16 bits 1K x 16 bits Page Size 256 x 16 bits 256 x 16 bits Please see the 56F8300 Peripheral User Manual for additional Flash information. 4.6 EOnCE Memory Map Table 4-8 EOnCE Memory Map Address Register Acronym Reserved X:$FF FF8A OESCR External Signal Control Register Reserved X:$FF FF8E OBCNTR Breakpoint Unit [0] Counter Reserved X:$FF FF90 X:$FF FF91 X:$FF FF92 X:$FF FF93 X:$FF FF94 X:$FF FF95 X:$FF FF96 X:$FF FF97 X:$FF FF98 X:$FF FF99 X:$FF FF9A X:$FF FF9B X:$FF FF9C X:$FF FF9D X:$FF FF9E X:$FF FF9F X:$FF FFA0 OBMSK (32 bits) — OBAR2 (32 bits) — OBAR1 (24 bits) — OBCR (24 bits) — OTB (21-24 bits/stage) — OTBPR (8 bits) OTBCR OBASE (8 bits) OSR OSCNTR (24 bits) — OCR (bits) Breakpoint 1 Unit [0] Mask Register Breakpoint 1 Unit [0] Mask Register Breakpoint 2 Unit [0] Address Register Breakpoint 2 Unit [0] Address Register Breakpoint 1 Unit [0] Address Register Breakpoint 1 Unit [0] Address Register Breakpoint Unit [0] Control Register Breakpoint Unit [0] Control Register Trace Buffer Register Stages Trace Buffer Register Stages Trace Buffer Pointer Register Trace Buffer Control Register Peripheral Base Address Register Status Register Instruction Step Counter Instruction Step Counter Control Register Reserved X:$FF FFFC X:$FF FFFD OCLSR (8 bits) OTXRXSR (8 bits) Core Lock / Unlock Status Register Transmit and Receive Status and Control Register Register Name 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 43 Table 4-8 EOnCE Memory Map (Continued) Address X:$FF FFFE X:$FF FFFF Register Acronym OTX / ORX (32 bits) OTX1 / ORX1 Register Name Transmit Register / Receive Register Transmit Register Upper Word Receive Register Upper Word 4.7 Peripheral Memory Mapped Registers On-chip peripheral registers are part of the data memory map on the 56800E series. These locations may be accessed with the same addressing modes used for ordinary Data memory, except all peripheral registers should be read/written using word accesses only. Table 4-9 summarizes base addresses for the set of peripherals on the 56F8335 and 56F8135 devices. Peripherals are listed in order of the base address. The following tables list all of the peripheral registers required to control or access the peripherals. Note: Features in italics are NOT available in the 56F8135 device. Table 4-9 Data Memory Peripheral Base Address Map Summary Peripheral External Memory Interface Timer A Timer B Timer C Timer D PWM A PWM B Quadrature Decoder 0 Quadrature Decoder 1 ITCN ADC A ADC B Temperature Sensor SCI #0 SCI #1 SPI #0 SPI #1 COP PLL, OSC GPIO Port A GPIO Port B EMI TMRA TMRB TMRC TMRD PWMA PWMB DEC0 DEC1 ITCN ADCA ADCB TSENSOR SCI0 SCI1 SPI0 SPI1 COP CLKGEN GPIOA GPIOB Prefix Base Address X:$00 F020 X:$00 F040 X:$00 F080 X:$00 F0C0 X:$00 F100 X:$00 F140 X:$00 F160 X:$00 F180 X:$00 F190 X:$00 F1A0 X:$00 F200 X:$00 F240 X:$00 F270 X:$00 F280 X:$00 F290 X:$00 F2A0 X:$00 F2B0 X:$00 F2C0 X:$00 F2D0 X:$00 F2E0 X:$00 F300 Table Number 4-10 4-11 4-12 4-13 4-14 4-15 4-16 4-17 4-18 4-19 4-20 4-21 4-22 4-23 4-24 4-25 4-26 4-27 4-28 4-29 4-30 56F8335 Technical Data, Rev. 5 44 Freescale Semiconductor Preliminary Peripheral Memory Mapped Registers Table 4-9 Data Memory Peripheral Base Address Map Summary (Continued) Peripheral GPIO Port C GPIO Port D GPIO Port E GPIO Port F SIM Power Supervisor FM FlexCAN Prefix GPIOC GPIOD GPIOE GPIOF SIM LVI FM FC Base Address X:$00 F310 X:$00 F320 X:$00 F330 X:$00 F340 X:$00 F350 X:$00 F360 X:$00 F400 X:$00 F800 Table Number 4-31 4-32 4-33 4-34 4-35 4-36 4-37 4-38 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 45 Table 4-10 External Memory Integration Registers Address Map (EMI_BASE = $00 F020) Register Acronym CSBAR 0 CSBAR 1 CSBAR 2 CSBAR 3 CSBAR 4 CSBAR 5 CSBAR 6 CSBAR 7 CSOR 0 CSOR 1 CSOR 2 CSOR 3 CSOR 4 CSOR 5 CSOR 6 CSOR 7 CSTC 0 CSTC 1 CSTC 2 CSTC 3 CSTC 4 CSTC 5 CSTC 6 CSTC 7 BCR Address Offset $0 $1 $2 $3 $4 $5 $6 $7 $8 $9 $A $B $C $D $E $F $10 $11 $12 $13 $14 $15 $16 $17 $18 Register Description Chip Select Base Address Register 0 Chip Select Base Address Register 1 Chip Select Base Address Register 2 Chip Select Base Address Register 3 Chip Select Base Address Register 4 Chip Select Base Address Register 5 Chip Select Base Address Register 6 Chip Select Base Address Register 7 Chip Select Option Register 0 Chip Select Option Register 1 Chip Select Option Register 2 Chip Select Option Register 3 Chip Select Option Register 4 Chip Select Option Register 5 Chip Select Option Register 6 Chip Select Option Register 7 Chip Select Timing Control Register 0 Chip Select Timing Control Register 1 Chip Select Timing Control Register 2 Chip Select Timing Control Register 3 Chip Select Timing Control Register 4 Chip Select Timing Control Register 5 Chip Select Timing Control Register 6 Chip Select Timing Control Register 7 Bus Control Register Reset Values 0 x 0004 = 64K since EXTBOOT = EMI_MODE = 0 0 x 0004 = 64K since EMI_MODE = 0 Table 4-11 Quad Timer A Registers Address Map (TMRA_BASE = $00 F040) Register Acronym TMRA0_CMP1 TMRA0_CMP2 TMRA0_CAP TMRA0_LOAD TMRA0_HOLD Address Offset $0 $1 $2 $3 $4 Register Description Compare Register 1 Compare Register 2 Capture Register Load Register Hold Register 56F8335 Technical Data, Rev. 5 46 Freescale Semiconductor Preliminary This table added to provide complete information, but this peripheral is not functional in the 56F8335/56F8135 package Peripheral Memory Mapped Registers Table 4-11 Quad Timer A Registers Address Map (Continued) (TMRA_BASE = $00 F040) Register Acronym TMRA0_CNTR TMRA0_CTRL TMRA0_SCR TMRA0_CMPLD1 TMRA0_CMPLD2 TMRA0_COMSCR Address Offset $5 $6 $7 $8 $9 $A Register Description Counter Register Control Register Status and Control Register Comparator Load Register 1 Comparator Load Register 2 Comparator Status and Control Register Reserved TMRA1_CMP1 TMRA1_CMP2 TMRA1_CAP TMRA1_LOAD TMRA1_HOLD TMRA1_CNTR TMRA1_CTRL TMRA1_SCR TMRA1_CMPLD1 TMRA1_CMPLD2 TMRA1_COMSCR $10 $11 $12 $13 $14 $15 $16 $17 $18 $19 $1A Compare Register 1 Compare Register 2 Capture Register Load Register Hold Register Counter Register Control Register Status and Control Register Comparator Load Register 1 Comparator Load Register 2 Comparator Status and Control Register Reserved TMRA2_CMP1 TMRA2_CMP2 TMRA2_CAP TMRA2_LOAD TMRA2_HOLD TMRA2_CNTR TMRA2_CTRL TMRA2_SCR TMRA2_CMPLD1 TMRA2_CMPLD2 TMRA2_COMSCR $20 $21 $22 $23 $24 $25 $26 $27 $28 $29 $2A Compare Register 1 Compare Register 2 Capture Register Load Register Hold Register Counter Register Control Register Status and Control Register Comparator Load Register 1 Comparator Load Register 2 Comparator Status and Control Register Reserved 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 47 Table 4-11 Quad Timer A Registers Address Map (Continued) (TMRA_BASE = $00 F040) Register Acronym TMRA3_CMP1 TMRA3_CMP2 TMRA3_CAP TMRA3_LOAD TMRA3_HOLD TMRA3_CNTR TMRA3_CTRL TMRA3_SCR TMRA3_CMPLD1 TMRA3_CMPLD2 TMRA3_COMSCR Address Offset $30 $31 $32 $33 $34 $35 $36 $37 $38 $39 $3A Register Description Compare Register 1 Compare Register 2 Capture Register Load Register Hold Register Counter Register Control Register Status and Control Register Comparator Load Register 1 Comparator Load Register 2 Comparator Status and Control Register Table 4-12 Quad Timer B Registers Address Map (TMRB_BASE = $00 F080) Quad Timer B is NOT available in the 56F8135 device Register Acronym TMRB0_CMP1 TMRB0_CMP2 TMRB0_CAP TMRB0_LOAD TMRB0_HOLD TMRB0_CNTR TMRB0_CTRL TMRB0_SCR TMRB0_CMPLD1 TMRB0_CMPLD2 TMRB0_COMSCR Address Offset $0 $1 $2 $3 $4 $5 $6 $7 $8 $9 $A Register Description Compare Register 1 Compare Register 2 Capture Register Load Register Hold Register Counter Register Control Register Status and Control Register Comparator Load Register 1 Comparator Load Register 2 Comparator Status and Control Register Reserved TMRB1_CMP1 TMRB1_CMP2 TMRB1_CAP TMRB1_LOAD TMRB1_HOLD TMRB1_CNTR $10 $11 $12 $13 $14 $15 Compare Register 1 Compare Register 2 Capture Register Load Register Hold Register Counter Register 56F8335 Technical Data, Rev. 5 48 Freescale Semiconductor Preliminary Peripheral Memory Mapped Registers Table 4-12 Quad Timer B Registers Address Map (Continued) (TMRB_BASE = $00 F080) Quad Timer B is NOT available in the 56F8135 device Register Acronym TMRB1_CTRL TMRB1_SCR TMRB1_CMPLD1 TMRB1_CMPLD2 TMRB1_COMSCR Address Offset $16 $17 $18 $19 $1A Control Register Status and Control Register Comparator Load Register 1 Comparator Load Register 2 Comparator Status and Control Register Reserved TMRB2_CMP1 TMRB2_CMP2 TMRB2_CAP TMRB2_LOAD TMRB2_HOLD TMRB2_CNTR TMRB2_CTRL TMRB2_SCR TMRB2_CMPLD1 TMRB2_CMPLD2 TMRB2_COMSCR $20 $21 $22 $23 $24 $25 $26 $27 $28 $29 $2A Compare Register 1 Compare Register 2 Capture Register Load Register Hold Register Counter Register Control Register Status and Control Register Comparator Load Register 1 Comparator Load Register 2 Comparator Status and Control Register Reserved TMRB3_CMP1 TMRB3_CMP2 TMRB3_CAP TMRB3_LOAD TMRB3_HOLD TMRB3_CNTR TMRB3_CTRL TMRB3_SCR TMRB3_CMPLD1 TMRB3_CMPLD2 TMRB3_COMSCR $30 $31 $32 $33 $34 $35 $36 $37 $38 $39 $3A Compare Register 1 Compare Register 2 Capture Register Load Register Hold Register Counter Register Control Register Status and Control Register Comparator Load Register 1 Comparator Load Register 2 Comparator Status and Control Register Register Description 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 49 Table 4-13 Quad Timer C Registers Address Map (TMRC_BASE = $00 F0C0) Register Acronym TMRC0_CMP1 TMRC0_CMP2 TMRC0_CAP TMRC0_LOAD TMRC0_HOLD TMRC0_CNTR TMRC0_CTRL TMRC0_SCR TMRC0_CMPLD1 TMRC0_CMPLD2 TMRC0_COMSCR Address Offset $0 $1 $2 $3 $4 $5 $6 $7 $8 $9 $A Register Description Compare Register 1 Compare Register 2 Capture Register Load Register Hold Register Counter Register Control Register Status and Control Register Comparator Load Register 1 Comparator Load Register 2 Comparator Status and Control Register Reserved TMRC1_CMP1 TMRC1_CMP2 TMRC1_CAP TMRC1_LOAD TMRC1_HOLD TMRC1_CNTR TMRC1_CTRL TMRC1_SCR TMRC1_CMPLD1 TMRC1_CMPLD2 TMRC1_COMSCR $10 $11 $12 $13 $14 $15 $16 $17 $18 $19 $1A Compare Register 1 Compare Register 2 Capture Register Load Register Hold Register Counter Register Control Register Status and Control Register Comparator Load Register 1 Comparator Load Register 2 Comparator Status and Control Register Reserved TMRC2_CMP1 TMRC2_CMP2 TMRC2_CAP TMRC2_LOAD TMRC2_HOLD TMRC2_CNTR TMRC2_CTRL TMRC2_SCR TMRC2_CMPLD1 $20 $21 $22 $23 $24 $25 $26 $27 $28 Compare Register 1 Compare Register 2 Capture Register Load Register Hold Register Counter Register Control Register Status and Control Register Comparator Load Register 1 56F8335 Technical Data, Rev. 5 50 Freescale Semiconductor Preliminary Peripheral Memory Mapped Registers Table 4-13 Quad Timer C Registers Address Map (Continued) (TMRC_BASE = $00 F0C0) Register Acronym TMRC2_CMPLD2 TMRC2_COMSCR Address Offset $29 $2A Register Description Comparator Load Register 2 Comparator Status and Control Register Reserved TMRC3_CMP1 TMRC3_CMP2 TMRC3_CAP TMRC3_LOAD TMRC3_HOLD TMRC3_CNTR TMRC3_CTRL TMRC3_SCR TMRC3_CMPLD1 TMRC3_CMPLD2 TMRC3_COMSCR $30 $31 $32 $33 $34 $35 $36 $37 $38 $39 $3A Compare Register 1 Compare Register 2 Capture Register Load Register Hold Register Counter Register Control Register Status and Control Register Comparator Load Register 1 Comparator Load Register 2 Comparator Status and Control Register Table 4-14 Quad Timer D Registers Address Map (TMRD_BASE = $00 F100) Quad Timer D is NOT available in the 56F8135 device Register Acronym TMRD0_CMP1 TMRD0_CMP2 TMRD0_CAP TMRD0_LOAD TMRD0_HOLD TMRD0_CNTR TMRD0_CTRL TMRD0_SCR TMRD0_CMPLD1 TMRD0_CMPLD2 TMRD0_COMSCR Address Offset $0 $1 $2 $3 $4 $5 $6 $7 $8 $9 $A Register Description Compare Register 1 Compare Register 2 Capture Register Load Register Hold Register Counter Register Control Register Status and Control Register Comparator Load Register 1 Comparator Load Register 2 Comparator Status and Control Register Reserved TMRD1_CMP1 TMRD1_CMP2 $10 $11 Compare Register 1 Compare Register 2 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 51 Table 4-14 Quad Timer D Registers Address Map (Continued) (TMRD_BASE = $00 F100) Quad Timer D is NOT available in the 56F8135 device Register Acronym TMRD1_CAP TMRD1_LOAD TMRD1_HOLD TMRD1_CNTR TMRD1_CTRL TMRD1_SCR TMRD1_CMPLD1 TMRD1_CMPLD2 TMRD1_COMSCR Address Offset $12 $13 $14 $15 $16 $17 $18 $19 $1A Capture Register Load Register Hold Register Counter Register Control Register Status and Control Register Comparator Load Register 1 Comparator Load Register 2 Comparator Status and Control Register Reserved TMRD2_CMP1 TMRD2_CMP2 TMRD2_CAP TMRD2_LOAD TMRD2_HOLD TMRD2_CNTR TMRD2_CTRL TMRD2_SCR TMRD2_CMPLD1 TMRD2_CMPLD2 TMRD2_COMSCR $20 $21 $22 $23 $24 $25 $26 $27 $28 $29 $2A Compare Register 1 Compare Register 2 Capture Register Load Register Hold Register Counter Register Control Register Status and Control Register Comparator Load Register 1 Comparator Load Register 2 Comparator Status and Control Register Reserved TMRD3_CMP1 TMRD3_CMP2 TMRD3_CAP TMRD3_LOAD TMRD3_HOLD TMRD3_CNTR TMRD3_CTRL TMRD3_SCR TMRD3_CMPLD1 TMRD3_CMPLD2 TMRD3_COMSCR $30 $31 $32 $33 $34 $35 $36 $37 $38 $39 $3A Compare Register 1 Compare Register 2 Capture Register Load Register Hold Register Counter Register Control Register Status and Control Register Comparator Load Register 1 Comparator Load Register 2 Comparator Status and Control Register Register Description 56F8335 Technical Data, Rev. 5 52 Freescale Semiconductor Preliminary Peripheral Memory Mapped Registers Table 4-15 Pulse Width Modulator A Registers Address Map (PWMA_BASE = $00 F140) PWMA is NOT available in the 56F8135 device Register Acronym PWMA_PMCTL PWMA_PMFCTL PWMA_PMFSA PWMA_PMOUT PWMA_PMCNT PWMA_PWMCM PWMA_PWMVAL0 PWMA_PWMVAL1 PWMA_PWMVAL2 PWMA_PWMVAL3 PWMA_PWMVAL4 PWMA_PWMVAL5 PWMA_PMDEADTM PWMA_PMDISMAP1 PWMA_PMDISMAP2 PWMA_PMCFG PWMA_PMCCR PWMA_PMPORT PWMA_PMICCR Address Offset $0 $1 $2 $3 $4 $5 $6 $7 $8 $9 $A $B $C $D $E $F $10 $11 $12 Control Register Fault Control Register Fault Status Acknowledge Register Output Control Register Counter Register Counter Modulo Register Value Register 0 Value Register 1 Value Register 2 Value Register 3 Value Register 4 Value Register 5 Dead Time Register Disable Mapping Register 1 Disable Mapping Register 2 Configure Register Channel Control Register Port Register PWM Internal Correction Control Register Register Description Table 4-16 Pulse Width Modulator B Registers Address Map (PWMB_BASE = $00 F160) Register Acronym PWMB_PMCTL PWMB_PMFCTL PWMB_PMFSA PWMB_PMOUT PWMB_PMCNT PWMB_PWMCM PWMB_PWMVAL0 PWMB_PWMVAL1 Address Offset $0 $1 $2 $3 $4 $5 $6 $7 Control Register Fault Control Register Fault Status Acknowledge Register Output Control Register Counter Register Counter Modulo Register Value Register 0 Value Register 1 Register Description 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 53 Table 4-16 Pulse Width Modulator B Registers Address Map (Continued) (PWMB_BASE = $00 F160) Register Acronym PWMB_PWMVAL2 PWMB_PWMVAL3 PWMB_PWMVAL4 PWMB_PWMVAL5 PWMB_PMDEADTM PWMB_PMDISMAP1 PWMB_PMDISMAP2 PWMB_PMCFG PWMB_PMCCR PWMB_PMPORT PWMB_PMICCR Address Offset $8 $9 $A $B $C $D $E $F $10 $11 $12 Value Register 2 Value Register 3 Value Register 4 Value Register 5 Dead Time Register Disable Mapping Register 1 Disable Mapping Register 2 Configure Register Channel Control Register Port Register PWM Internal Correction Control Register Register Description Table 4-17 Quadrature Decoder 0 Registers Address Map (DEC0_BASE = $00 F180) Register Acronym DEC0_DECCR DEC0_FIR DEC0_WTR DEC0_POSD DEC0_POSDH DEC0_REV DEC0_REVH DEC0_UPOS DEC0_LPOS DEC0_UPOSH DEC0_LPOSH DEC0_UIR DEC0_LIR DEC0_IMR Address Offset $0 $1 $2 $3 $4 $5 $6 $7 $8 $9 $A $B $C $D Register Description Decoder Control Register Filter Interval Register Watchdog Time-out Register Position Difference Counter Register Position Difference Counter Hold Register Revolution Counter Register Revolution Hold Register Upper Position Counter Register Lower Position Counter Register Upper Position Hold Register Lower Position Hold Register Upper Initialization Register Lower Initialization Register Input Monitor Register 56F8335 Technical Data, Rev. 5 54 Freescale Semiconductor Preliminary Peripheral Memory Mapped Registers Table 4-18 Quadrature Decoder 1 Registers Address Map (DEC1_BASE = $00 F190) Quadrature Decoder 1 is NOT available in the 56F8135 device Register Acronym DEC1_DECCR DEC1_FIR DEC1_WTR DEC1_POSD DEC1_POSDH DEC1_REV DEC1_REVH DEC1_UPOS DEC1_LPOS DEC1_UPOSH DEC1_LPOSH DEC1_UIR DEC1_LIR DEC1_IMR Address Offset $0 $1 $2 $3 $4 $5 $6 $7 $8 $9 $A $B $C $D Register Description Decoder Control Register Filter Interval Register Watchdog Time-out Register Position Difference Counter Register Position Difference Counter Hold Register Revolution Counter Register Revolution Hold Register Upper Position Counter Register Lower Position Counter Register Upper Position Hold Register Lower Position Hold Register Upper Initialization Register Lower Initialization Register Input Monitor Register Table 4-19 Interrupt Control Registers Address Map (ITCN_BASE = $00 F1A0) Register Acronym IPR 0 IPR 1 IPR 2 IPR 3 IPR 4 IPR 5 IPR 6 IPR 7 IPR 8 IPR 9 Address Offset $0 $1 $2 $3 $4 $5 $6 $7 $8 $9 Register Description Interrupt Priority Register 0 Interrupt Priority Register 1 Interrupt Priority Register 2 Interrupt Priority Register 3 Interrupt Priority Register 4 Interrupt Priority Register 5 Interrupt Priority Register 6 Interrupt Priority Register 7 Interrupt Priority Register 8 Interrupt Priority Register 9 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 55 Table 4-19 Interrupt Control Registers Address Map (Continued) (ITCN_BASE = $00 F1A0) Register Acronym VBA FIM0 FIVAL0 FIVAH0 FIM1 FIVAL1 FIVAH1 IRQP 0 IRQP 1 IRQP 2 IRQP 3 IRQP 4 IRQP 5 Address Offset $A $B $C $D $E $F $10 $11 $12 $13 $14 $15 $16 Register Description Vector Base Address Register Fast Interrupt Match Register 0 Fast Interrupt Vector Address Low 0 Register Fast Interrupt Vector Address High 0 Register Fast Interrupt Match Register 1 Fast Interrupt Vector Address Low 1 Register Fast Interrupt Vector Address High 1 Register IRQ Pending Register 0 IRQ Pending Register 1 IRQ Pending Register 2 IRQ Pending Register 3 IRQ Pending Register 4 IRQ Pending Register 5 Reserved ICTL $1D Interrupt Control Register Table 4-20 Analog-to-Digital Converter Registers Address Map (ADCA_BASE = $00 F200) Register Acronym ADCA_CR1 ADCA_CR2 ADCA_ZCC ADCA_LST 1 ADCA_LST 2 ADCA_SDIS ADCA_STAT ADCA_LSTAT ADCA_ZCSTAT ADCA_RSLT 0 ADCA_RSLT 1 ADCA_RSLT 2 ADCA_RSLT 3 ADCA_RSLT 4 Address Offset $0 $1 $2 $3 $4 $5 $6 $7 $8 $9 $A $B $C $D Register Description Control Register 1 Control Register 2 Zero Crossing Control Register Channel List Register 1 Channel List Register 2 Sample Disable Register Status Register Limit Status Register Zero Crossing Status Register Result Register 0 Result Register 1 Result Register 2 Result Register 3 Result Register 4 56F8335 Technical Data, Rev. 5 56 Freescale Semiconductor Preliminary Peripheral Memory Mapped Registers Table 4-20 Analog-to-Digital Converter Registers Address Map (Continued) (ADCA_BASE = $00 F200) Register Acronym ADCA_RSLT 5 ADCA_RSLT 6 ADCA_RSLT 7 ADCA_LLMT 0 ADCA_LLMT 1 ADCA_LLMT 2 ADCA_LLMT 3 ADCA_LLMT 4 ADCA_LLMT 5 ADCA_LLMT 6 ADCA_LLMT 7 ADCA_HLMT 0 ADCA_HLMT 1 ADCA_HLMT 2 ADCA_HLMT 3 ADCA_HLMT 4 ADCA_HLMT 5 ADCA_HLMT 6 ADCA_HLMT 7 ADCA_OFS 0 ADCA_OFS 1 ADCA_OFS 2 ADCA_OFS 3 ADCA_OFS 4 ADCA_OFS 5 ADCA_OFS 6 ADCA_OFS 7 Address Offset $E $F $10 $11 $12 $13 $14 $15 $16 $17 $18 $19 $1A $1B $1C $1D $1E $1F $20 $21 $22 $23 $24 $25 $26 $27 $28 Register Description Result Register 5 Result Register 6 Result Register 7 Low Limit Register 0 Low Limit Register 1 Low Limit Register 2 Low Limit Register 3 Low Limit Register 4 Low Limit Register 5 Low Limit Register 6 Low Limit Register 7 High Limit Register 0 High Limit Register 1 High Limit Register 2 High Limit Register 3 High Limit Register 4 High Limit Register 5 High Limit Register 6 High Limit Register 7 Offset Register 0 Offset Register 1 Offset Register 2 Offset Register 3 Offset Register 4 Offset Register 5 Offset Register 6 Offset Register 7 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 57 Table 4-20 Analog-to-Digital Converter Registers Address Map (Continued) (ADCA_BASE = $00 F200) Register Acronym ADCA_POWER ADCA_CAL Address Offset $29 $2A Register Description Power Control Register ADC Calibration Register Table 4-21 Analog-to-Digital Converter Registers Address Map (ADCB_BASE = $00 F240) Register Acronym ADCB_CR1 ADCB_CR2 ADCB_ZCC ADCB_LST 1 ADCB_LST 2 ADCB_SDIS ADCB_STAT ADCB_LSTAT ADCB_ZCSTAT ADCB_RSLT 0 ADCB_RSLT 1 ADCB_RSLT 2 ADCB_RSLT 3 ADCB_RSLT 4 ADCB_RSLT 5 ADCB_RSLT 6 ADCB_RSLT 7 ADCB_LLMT 0 ADCB_LLMT 1 ADCB_LLMT 2 ADCB_LLMT 3 ADCB_LLMT 4 ADCB_LLMT 5 ADCB_LLMT 6 ADCB_LLMT 7 ADCB_HLMT 0 ADCB_HLMT 1 Address Offset $0 $1 $2 $3 $4 $5 $6 $7 $8 $9 $A $B $C $D $E $F $10 $11 $12 $13 $14 $15 $16 $17 $18 $19 $1A Register Description Control Register 1 Control Register 2 Zero Crossing Control Register Channel List Register 1 Channel List Register 2 Sample Disable Register Status Register Limit Status Register Zero Crossing Status Register Result Register 0 Result Register 1 Result Register 2 Result Register 3 Result Register 4 Result Register 5 Result Register 6 Result Register 7 Low Limit Register 0 Low Limit Register 1 Low Limit Register 2 Low Limit Register 3 Low Limit Register 4 Low Limit Register 5 Low Limit Register 6 Low Limit Register 7 High Limit Register 0 High Limit Register 1 56F8335 Technical Data, Rev. 5 58 Freescale Semiconductor Preliminary Peripheral Memory Mapped Registers Table 4-21 Analog-to-Digital Converter Registers Address Map (Continued) (ADCB_BASE = $00 F240) Register Acronym ADCB_HLMT 2 ADCB_HLMT 3 ADCB_HLMT 4 ADCB_HLMT 5 ADCB_HLMT 6 ADCB_HLMT 7 ADCB_OFS 0 ADCB_OFS 1 ADCB_OFS 2 ADCB_OFS 3 ADCB_OFS 4 ADCB_OFS 5 ADCB_OFS 6 ADCB_OFS 7 ADCB_POWER ADCB_CAL Address Offset $1B $1C $1D $1E $1F $20 $21 $22 $23 $24 $25 $26 $27 $28 $29 $2A Register Description High Limit Register 2 High Limit Register 3 High Limit Register 4 High Limit Register 5 High Limit Register 6 High Limit Register 7 Offset Register 0 Offset Register 1 Offset Register 2 Offset Register 3 Offset Register 4 Offset Register 5 Offset Register 6 Offset Register 7 Power Control Register ADC Calibration Register Table 4-22 Temperature Sensor Register Address Map (TSENSOR_BASE = $00 F270) Temperature Sensor is NOT available in the 56F8135 device Register Acronym TSENSOR_CNTL Address Offset $0 Control Register Register Description Table 4-23 Serial Communication Interface 0 Registers Address Map (SCI0_BASE = $00 F280) Register Acronym SCI0_SCIBR Address Offset $0 Register Description Baud Rate Register 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 59 Table 4-23 Serial Communication Interface 0 Registers Address Map (Continued) (SCI0_BASE = $00 F280) Register Acronym SCI0_SCICR Address Offset $1 Control Register Reserved SCI0_SCISR SCI0_SCIDR $3 $4 Status Register Data Register Register Description Table 4-24 Serial Communication Interface 1 Registers Address Map (SCI1_BASE = $00 F290) Register Acronym SCI1_SCIBR SCI1_SCICR Address Offset $0 $1 Register Description Baud Rate Register Control Register Reserved SCI1_SCISR SCI1_SCIDR $3 $4 Status Register Data Register Table 4-25 Serial Peripheral Interface 0 Registers Address Map (SPI0_BASE = $00 F2A0) Register Acronym SPI0_SPSCR SPI0_SPDSR SPI0_SPDRR SPI0_SPDTR Address Offset $0 $1 $2 $3 Register Description Status and Control Register Data Size Register Data Receive Register Data Transmitter Register Table 4-26 Serial Peripheral Interface 1 Registers Address Map (SPI1_BASE = $00 F2B0) Register Acronym SPI1_SPSCR SPI1_SPDSR SPI1_SPDRR SPI1_SPDTR Address Offset $0 $1 $2 $3 Register Description Status and Control Register Data Size Register Data Receive Register Data Transmitter Register 56F8335 Technical Data, Rev. 5 60 Freescale Semiconductor Preliminary Peripheral Memory Mapped Registers Table 4-27 Computer Operating Properly Registers Address Map (COP_BASE = $00 F2C0) Register Acronym COPCTL COPTO COPCTR Address Offset $0 $1 $2 Control Register Time-Out Register Counter Register Register Description Table 4-28 Clock Generation Module Registers Address Map (CLKGEN_BASE = $00 F2D0) Register Acronym PLLCR PLLDB PLLSR Address Offset $0 $1 $2 Control Register Divide-By Register Status Register Reserved SHUTDOWN OSCTL $4 $5 Shutdown Register Oscillator Control Register Register Description Table 4-29 GPIOA Registers Address Map (GPIOA_BASE = $00 F2E0) Register Acronym GPIOA_PUR GPIOA_DR GPIOA_DDR GPIOA_PER GPIOA_IAR GPIOA_IENR GPIOA_IPOLR GPIOA_IPR GPIOA_IESR GPIOA_PPMODE GPIOA_RAWDATA Address Offset $0 $1 $2 $3 $4 $5 $6 $7 $8 $9 $A Register Description Pull-up Enable Register Data Register Data Direction Register Peripheral Enable Register Interrupt Assert Register Interrupt Enable Register Interrupt Polarity Register Interrupt Pending Register Interrupt Edge-Sensitive Register Push-Pull Mode Register Raw Data Input Register Reset Value 0 x 3FFF 0 x 0000 0 x 0000 0 x 3FFF 0 x 0000 0 x 0000 0 x 0000 0 x 0000 0 x 0000 0 x 3FFF — 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 61 Table 4-30 GPIOB Registers Address Map (GPIOB_BASE = $00 F300) Register Acronym GPIOB_PUR GPIOB_DR GPIOB_DDR GPIOB_PER GPIOB_IAR GPIOB_IENR GPIOB_IPOLR GPIOB_IPR GPIOB_IESR GPIOB_PPMODE GPIOB_RAWDATA Address Offset $0 $1 $2 $3 $4 $5 $6 $7 $8 $9 $A Register Description Pull-up Enable Register Data Register Data Direction Register Peripheral Enable Register Interrupt Assert Register Interrupt Enable Register Interrupt Polarity Register Interrupt Pending Register Interrupt Edge-Sensitive Register Push-Pull Mode Register Raw Data Input Register Reset Value 0 x 00FF 0 x 0000 0 x 0000 0 x 0000 0 x 0000 0 x 0000 0 x 0000 0 x 0000 0 x 0000 0 x 00FF — Table 4-31 GPIOC Registers Address Map (GPIOC_BASE = $00 F310) Register Acronym GPIOC_PUR GPIOC_DR GPIOC_DDR GPIOC_PER GPIOC_IAR GPIOC_IENR GPIOC_IPOLR GPIOC_IPR GPIOC_IESR GPIOC_PPMODE GPIOC_RAWDATA Address Offset $0 $1 $2 $3 $4 $5 $6 $7 $8 $9 $A Register Description Pull-up Enable Register Data Register Data Direction Register Peripheral Enable Register Interrupt Assert Register Interrupt Enable Register Interrupt Polarity Register Interrupt Pending Register Interrupt Edge-Sensitive Register Push-Pull Mode Register Raw Data Input Register Reset Value 0 x 07FF 0 x 0000 0 x 0000 0 x 07FF 0 x 0000 0 x 0000 0 x 0000 0 x 0000 0 x 0000 0 x 07FF — 56F8335 Technical Data, Rev. 5 62 Freescale Semiconductor Preliminary Peripheral Memory Mapped Registers Table 4-32 GPIOD Registers Address Map (GPIOD_BASE = $00 F320) Register Acronym GPIOD_PUR GPIOD_DR GPIOD_DDR GPIOD_PER GPIOD_IAR GPIOD_IENR GPIOD_IPOLR GPIOD_IPR GPIOD_IESR GPIOD_PPMODE GPIOD_RAWDATA Address Offset $0 $1 $2 $3 $4 $5 $6 $7 $8 $9 $A Register Description Pull-up Enable Register Data Register Data Direction Register Peripheral Enable Register Interrupt Assert Register Interrupt Enable Register Interrupt Polarity Register Interrupt Pending Register Interrupt Edge-Sensitive Register Push-Pull Mode Register Raw Data Input Register Reset Value 0 x 1FFF 0 x 0000 0 x 0000 0 x 1FC0 0 x 0000 0 x 0000 0 x 0000 0 x 0000 0 x 0000 0 x 1FFF — Table 4-33 GPIOE Registers Address Map (GPIOE_BASE = $00 F330) Register Acronym GPIOE_PUR GPIOE_DR GPIOE_DDR GPIOE_PER GPIOE_IAR GPIOE_IENR GPIOE_IPOLR GPIOE_IPR GPIOE_IESR GPIOE_PPMODE GPIOE_RAWDATA Address Offset $0 $1 $2 $3 $4 $5 $6 $7 $8 $9 $A Register Description Pull-up Enable Register Data Register Data Direction Register Peripheral Enable Register Interrupt Assert Register Interrupt Enable Register Interrupt Polarity Register Interrupt Pending Register Interrupt Edge-Sensitive Register Push-Pull Mode Register Raw Data Input Register Reset Value 0 x 3FFF 0 x 0000 0 x 0000 0 x 3FFF 0 x 0000 0 x 0000 0 x 0000 0 x 0000 0 x 0000 0 x 3FFF — 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 63 Table 4-34 GPIOF Registers Address Map (GPIOF_BASE = $00 F340) Register Acronym GPIOF_PUR GPIOF_DR GPIOF_DDR GPIOF_PER GPIOF_IAR GPIOF_IENR GPIOF_IPOLR GPIOF_IPR GPIOF_IESR GPIOF_PPMODE GPIOF_RAWDATA Address Offset $0 $1 $2 $3 $4 $5 $6 $7 $8 $9 $A Register Description Pull-up Enable Register Data Register Data Direction Register Peripheral Enable Register Interrupt Assert Register Interrupt Enable Register Interrupt Polarity Register Interrupt Pending Register Interrupt Edge-Sensitive Register Push-Pull Mode Register Raw Data Input Register Reset Value 0 x FFFF 0 x 0000 0 x 0000 0 x FFFF 0 x 0000 0 x 0000 0 x 0000 0 x 0000 0 x 0000 0 x FFFF — Table 4-35 System Integration Module Registers Address Map (SIM_BASE = $00 F350) Register Acronym SIM_CONTROL SIM_RSTSTS SIM_SCR0 SIM_SCR1 SIM_SCR2 SIM_SCR3 SIM_MSH_ID SIM_LSH_ID SIM_PUDR Address Offset $0 $1 $2 $3 $4 $5 $6 $7 $8 Control Register Reset Status Register Software Control Register 0 Software Control Register 1 Software Control Register 2 Software Control Register 3 Most Significant Half JTAG ID Least Significant Half JTAG ID Pull-up Disable Register Reserved SIM_CLKOSR SIM_GPS SIM_PCE SIM_ISALH SIM_ISALL $A $B $C $D $E Clock Out Select Register Quad Decoder 1 / Timer B / SPI 1 Select Register Peripheral Clock Enable Register I/O Short Address Location High Register I/O Short Address Location Low Register Register Description 56F8335 Technical Data, Rev. 5 64 Freescale Semiconductor Preliminary Peripheral Memory Mapped Registers Table 4-36 Power Supervisor Registers Address Map (LVI_BASE = $00 F360) Register Acronym LVI_CONTROL LVI_STATUS Address Offset $0 $1 Control Register Status Register Register Description Table 4-37 Flash Module Registers Address Map (FM_BASE = $00 F400) Register Acronym FMCLKD FMMCR Address Offset $0 $1 Register Description Clock Divider Register Module Control Register Reserved FMSECH FMSECL $3 $4 Security High Half Register Security Low Half Register Reserved Reserved FMPROT FMPROTB $10 $11 Protection Register (Banked) Protection Boot Register (Banked) Reserved FMUSTAT FMCMD $13 $14 User Status Register (Banked) Command Register (Banked) Reserved Reserved FMOPT 0 $1A 16-Bit Information Option Register 0 Hot temperature ADC reading of Temperature Sensor; value set during factory test 16-Bit Information Option Register 1 Not used 16-Bit Information Option Register 2 Room temperature ADC reading of Temperature Sensor; value set during factory test FMOPT 1 FMOPT 2 $1B $1C 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 65 Table 4-38 FlexCAN Registers Address Map (FC_BASE = $00 F800) FlexCAN is NOT available in the 56F8135 device Register Acronym FCMCR Address Offset $0 Register Description Module Configuration Register Reserved FCCTL0 FCCTL1 FCTMR FCMAXMB $3 $4 $5 $6 Control Register 0 Register Control Register 1 Register Free-Running Timer Register Maximum Message Buffer Configuration Register Reserved FCRXGMASK_H FCRXGMASK_L FCRX14MASK_H FCRX14MASK_L FCRX15MASK_H FCRX15MASK_L $8 $9 $A $B $C $D Receive Global Mask High Register Receive Global Mask Low Register Receive Buffer 14 Mask High Register Receive Buffer 14 Mask Low Register Receive Buffer 15 Mask High Register Receive Buffer 15 Mask Low Register Reserved FCSTATUS FCIMASK1 FCIFLAG1 FCR/T_ERROR_CNTRS $10 $11 $12 $13 Error and Status Register Interrupt Masks 1 Register Interrupt Flags 1 Register Receive and Transmit Error Counters Register Reserved Reserved Reserved FCMB0_CONTROL FCMB0_ID_HIGH FCMB0_ID_LOW FCMB0_DATA FCMB0_DATA FCMB0_DATA FCMB0_DATA $40 $41 $42 $43 $44 $45 $46 Message Buffer 0 Control / Status Register Message Buffer 0 ID High Register Message Buffer 0 ID Low Register Message Buffer 0 Data Register Message Buffer 0 Data Register Message Buffer 0 Data Register Message Buffer 0 Data Register Reserved FCMSB1_CONTROL FCMSB1_ID_HIGH $48 $49 Message Buffer 1 Control / Status Register Message Buffer 1 ID High Register 56F8335 Technical Data, Rev. 5 66 Freescale Semiconductor Preliminary Peripheral Memory Mapped Registers Table 4-38 FlexCAN Registers Address Map (Continued) (FC_BASE = $00 F800) FlexCAN is NOT available in the 56F8135 device Register Acronym FCMSB1_ID_LOW FCMB1_DATA FCMB1_DATA FCMB1_DATA FCMB1_DATA Address Offset $4A $4B $4C $4D $4E Register Description Message Buffer 1 ID Low Register Message Buffer 1 Data Register Message Buffer 1 Data Register Message Buffer 1 Data Register Message Buffer 1 Data Register Reserved FCMB2_CONTROL FCMB2_ID_HIGH FCMB2_ID_LOW FCMB2_DATA FCMB2_DATA FCMB2_DATA FCMB2_DATA $50 $51 $52 $53 $54 $55 $56 Message Buffer 2 Control / Status Register Message Buffer 2 ID High Register Message Buffer 2 ID Low Register Message Buffer 2 Data Register Message Buffer 2 Data Register Message Buffer 2 Data Register Message Buffer 2 Data Register Reserved FCMB3_CONTROL FCMB3_ID_HIGH FCMB3_ID_LOW FCMB3_DATA FCMB3_DATA FCMB3_DATA FCMB3_DATA $58 $59 $5A $5B $5C $5D $5E Message Buffer 3 Control / Status Register Message Buffer 3 ID High Register Message Buffer 3 ID Low Register Message Buffer 3 Data Register Message Buffer 3 Data Register Message Buffer 3 Data Register Message Buffer 3 Data Register Reserved FCMB4_CONTROL FCMB4_ID_HIGH FCMB4_ID_LOW FCMB4_DATA FCMB4_DATA FCMB4_DATA FCMB4_DATA $60 $61 $62 $63 $64 $65 $66 Message Buffer 4 Control / Status Register Message Buffer 4 ID High Register Message Buffer 4 ID Low Register Message Buffer 4 Data Register Message Buffer 4 Data Register Message Buffer 4 Data Register Message Buffer 4 Data Register Reserved FCMB5_CONTROL FCMB5_ID_HIGH FCMB5_ID_LOW $68 $69 $6A Message Buffer 5 Control / Status Register Message Buffer 5 ID High Register Message Buffer 5 ID Low Register 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 67 Table 4-38 FlexCAN Registers Address Map (Continued) (FC_BASE = $00 F800) FlexCAN is NOT available in the 56F8135 device Register Acronym FCMB5_DATA FCMB5_DATA FCMB5_DATA FCMB5_DATA Address Offset $6B $6C $6D $6E Register Description Message Buffer 5 Data Register Message Buffer 5 Data Register Message Buffer 5 Data Register Message Buffer 5 Data Register Reserved FCMB6_CONTROL FCMB6_ID_HIGH FCMB6_ID_LOW FCMB6_DATA FCMB6_DATA FCMB6_DATA FCMB6_DATA $70 $71 $72 $73 $74 $75 $76 Message Buffer 6 Control / Status Register Message Buffer 6 ID High Register Message Buffer 6 ID Low Register Message Buffer 6 Data Register Message Buffer 6 Data Register Message Buffer 6 Data Register Message Buffer 6 Data Register Reserved FCMB7_CONTROL FCMB7_ID_HIGH FCMB7_ID_LOW FCMB7_DATA FCMB7_DATA FCMB7_DATA FCMB7_DATA $78 $79 $7A $7B $7C $7D $7E Message Buffer 7 Control / Status Register Message Buffer 7 ID High Register Message Buffer 7 ID Low Register Message Buffer 7 Data Register Message Buffer 7 Data Register Message Buffer 7 Data Register Message Buffer 7 Data Register Reserved FCMB8_CONTROL FCMB8_ID_HIGH FCMB8_ID_LOW FCMB8_DATA FCMB8_DATA FCMB8_DATA FCMB8_DATA $80 $81 $82 $83 $84 $85 $86 Message Buffer 8 Control / Status Register Message Buffer 8 ID High Register Message Buffer 8 ID Low Register Message Buffer 8 Data Register Message Buffer 8 Data Register Message Buffer 8 Data Register Message Buffer 8 Data Register Reserved FCMB9_CONTROL FCMB9_ID_HIGH $88 $89 Message Buffer 9 Control / Status Register Message Buffer 9 ID High Register 56F8335 Technical Data, Rev. 5 68 Freescale Semiconductor Preliminary Peripheral Memory Mapped Registers Table 4-38 FlexCAN Registers Address Map (Continued) (FC_BASE = $00 F800) FlexCAN is NOT available in the 56F8135 device Register Acronym FCMB9_ID_LOW FCMB9_DATA FCMB9_DATA FCMB9_DATA FCMB9_DATA Address Offset $8A $8B $8C $8D $8E Register Description Message Buffer 9 ID Low Register Message Buffer 9 Data Register Message Buffer 9 Data Register Message Buffer 9 Data Register Message Buffer 9 Data Register Reserved FCMB10_CONTROL FCMB10_ID_HIGH FCMB10_ID_LOW FCMB10_DATA FCMB10_DATA FCMB10_DATA FCMB10_DATA $90 $91 $92 $93 $94 $95 $96 Message Buffer 10 Control / Status Register Message Buffer 10 ID High Register Message Buffer 10 ID Low Register Message Buffer 10 Data Register Message Buffer 10 Data Register Message Buffer 10 Data Register Message Buffer 10 Data Register Reserved FCMB11_CONTROL FCMB11_ID_HIGH FCMB11_ID_LOW FCMB11_DATA FCMB11_DATA FCMB11_DATA FCMB11_DATA $98 $99 $9A $9B $9C $9D $9E Message Buffer 11 Control / Status Register Message Buffer 11 ID High Register Message Buffer 11 ID Low Register Message Buffer 11 Data Register Message Buffer 11 Data Register Message Buffer 11 Data Register Message Buffer 11 Data Register Reserved FCMB12_CONTROL FCMB12_ID_HIGH FCMB12_ID_LOW FCMB12_DATA FCMB12_DATA FCMB12_DATA FCMB12_DATA $A0 $A1 $A2 $A3 $A4 $A5 $A6 Message Buffer 12 Control / Status Register Message Buffer 12 ID High Register Message Buffer 12 ID Low Register Message Buffer 12 Data Register Message Buffer 12 Data Register Message Buffer 12 Data Register Message Buffer 12 Data Register Reserved FCMB13_CONTROL FCMB13_ID_HIGH FCMB13_ID_LOW $A8 $A9 $AA Message Buffer 13 Control / Status Register Message Buffer 13 ID High Register Message Buffer 13 ID Low Register 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 69 Table 4-38 FlexCAN Registers Address Map (Continued) (FC_BASE = $00 F800) FlexCAN is NOT available in the 56F8135 device Register Acronym FCMB13_DATA FCMB13_DATA FCMB13_DATA FCMB13_DATA Address Offset $AB $AC $AD $AE Register Description Message Buffer 13 Data Register Message Buffer 13 Data Register Message Buffer 13 Data Register Message Buffer 13 Data Register Reserved FCMB14_CONTROL FCMB14_ID_HIGH FCMB14_ID_LOW FCMB14_DATA FCMB14_DATA FCMB14_DATA FCMB14_DATA $B0 $B1 $B2 $B3 $B4 $B5 $B6 Message Buffer 14 Control / Status Register Message Buffer 14 ID High Register Message Buffer 14 ID Low Register Message Buffer 14 Data Register Message Buffer 14 Data Register Message Buffer 14 Data Register Message Buffer 14 Data Register Reserved FCMB15_CONTROL FCMB15_ID_HIGH FCMB15_ID_LOW FCMB15_DATA FCMB15_DATA FCMB15_DATA FCMB15_DATA $B8 $B9 $BA $BB $BC $BD $BE Message Buffer 15 Control / Status Register Message Buffer 15 ID High Register Message Buffer 15 ID Low Register Message Buffer 15 Data Register Message Buffer 15 Data Register Message Buffer 15 Data Register Message Buffer 15 Data Register Reserved 56F8335 Technical Data, Rev. 5 70 Freescale Semiconductor Preliminary Factory Programmed Memory 4.8 Factory Programmed Memory The Boot Flash memory block is programmed during manufacturing with a default Serial Bootloader program. The Serial Bootloader application can be used to load a user application into the Program and Data Flash(NOT available in the 56F8135) memories of the device. The 56F83xx SCI/CAN Bootloader User Manual (MC56F83xxBLUM) provides detailed information on this firmware. An application note, Production Flash Programming (AN1973), details how the Serial Bootloader program can be used to perform production Flash programming of the on-board Flash memories as well as other potential methods. Like all the Flash memory blocks, the Boot Flash can be erased and programmed by the user. The Serial Bootloader application is programmed as an aid to the end user, but is not required to be used or maintained in the Boot Flash memory. Part 5 Interrupt Controller (ITCN) 5.1 Introduction The Interrupt Controller (ITCN) module is used to arbitrate between various interrupt requests (IRQs), to signal to the 56800E core when an interrupt of sufficient priority exists, and to what address to jump in order to service this interrupt. 5.2 Features The ITCN module design includes these distinctive features: • • • • Programmable priority levels for each IRQ Two programmable Fast Interrupts Notification to SIM module to restart clocks out of Wait and Stop modes Drives initial address on the address bus after reset For further information, see Table 4-5, Interrupt Vector Table Contents. 5.3 Functional Description The Interrupt Controller is a slave on the IPBus. It contains registers allowing each of the 82 interrupt sources to be set to one of four priority levels, excluding certain interrupts of fixed priority. Next, all of the interrupt requests of a given level are priority encoded to determine the lowest numerical value of the active interrupt requests for that level. Within a given priority level, 0 is the highest priority, while number 81 is the lowest. 5.3.1 Normal Interrupt Handling Once the ITCN has determined that an interrupt is to be serviced and which interrupt has the highest priority, an interrupt vector address is generated. Normal interrupt handling concatenates the VBA and the vector number to determine the vector address. In this way, an offset is generated into the vector table for each interrupt. 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 71 5.3.2 Interrupt Nesting Interrupt exceptions may be nested to allow an IRQ of higher priority than the current exception to be serviced. The following tables define the nesting requirements for each priority level. Table 5-1 Interrupt Mask Bit Definition SR[9]1 0 0 1 1 SR[8]1 0 1 0 1 Permitted Exceptions Priorities 0, 1, 2, 3 Priorities 1, 2, 3 Priorities 2, 3 Priority 3 Masked Exceptions None Priority 0 Priorities 0, 1 Priorities 0, 1, 2 1. Core status register bits indicating current interrupt mask within the core. Table 5-2. Interrupt Priority Encoding IPIC_LEVEL[1:0]1 00 01 10 11 Current Interrupt Priority Level No Interrupt or SWILP Priority 0 Priority 1 Priorities 2 or 3 Required Nested Exception Priority Priorities 0, 1, 2, 3 Priorities 1, 2, 3 Priorities 2, 3 Priority 3 1. See IPIC field definition in Part 5.6.30.2 5.3.3 Fast Interrupt Handling Fast interrupts are described in the DSP56F800E Reference Manual. The interrupt controller recognizes fast interrupts before the core does. A fast interrupt is defined (to the ITCN) by: 1. Setting the priority of the interrupt as level 2, with the appropriate field in the IPR registers 2. Setting the FIMn register to the appropriate vector number 3. Setting the FIVALn and FIVAHn registers with the address of the code for the fast interrupt When an interrupt occurs, its vector number is compared with the FIM0 and FIM1 register values. If a match occurs, and it is a level 2 interrupt, the ITCN handles it as a fast interrupt. The ITCN takes the vector address from the appropriate FIVALn and FIVAHn registers, instead of generating an address that is an offset from the VBA. The core then fetches the instruction from the indicated vector adddress and if it is not a JSR, the core starts its fast interrupt handling. 56F8335 Technical Data, Rev. 5 72 Freescale Semiconductor Preliminary Block Diagram 5.4 Block Diagram Priority Level any0 Level 0 82 -> 7 Priority Encoder 7 INT1 2 -> 4 Decode INT VAB CONTROL IPIC any3 Level 3 Priority Level 82 -> 7 Priority Encoder IACK SR[9:8] 7 PIC_EN INT82 2 -> 4 Decode Figure 5-1 Interrupt Controller Block Diagram 5.5 Operating Modes The ITCN module design contains two major modes of operation: • • Functional Mode The ITCN is in this mode by default. Wait and Stop Modes During Wait and Stop modes, the system clocks and the 56800E core are turned off. The ITCN will signal a pending IRQ to the System Integration Module (SIM) to restart the clocks and service the IRQ. An IRQ can only wake up the core if the IRQ is enabled prior to entering the Wait or Stop mode. Also, the IRQA and IRQB signals automatically become low-level sensitive in these modes, even if the control register bits are set to make them falling-edge sensitive. This is because there is no clock available to detect the falling edge. A peripheral which requires a clock to generate interrupts will not be able to generate interrupts during Stop mode. The FlexCAN module can wake the device from Stop mode, and a reset will do just that, or IRQA and IRQB can wake it up. 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 73 5.6 Register Descriptions A register address is the sum of a base address and an address offset. The base address is defined at the system level and the address offset is defined at the module level. The ITCN peripheral has 24 registers. Table 5-3 ITCN Register Summary (ITCN_BASE = $00F1A0) Register Acronym IPR0 IPR1 IPR2 IPR3 IPR4 IPR5 IPR6 IPR7 IPR8 IPR9 VBA FIM0 FIVAL0 FIVAH0 FIM1 FIVAL1 FIVAH1 IRQP0 IRQP1 IRQP2 IRQP3 IRQP4 IRQP5 Base Address + $0 $1 $2 $3 $4 $5 $6 $7 $8 $9 $A $B $C $D $E $F $10 $11 $12 $13 $14 $15 $16 Register Name Interrupt Priority Register 0 Interrupt Priority Register 1 Interrupt Priority Register 2 Interrupt Priority Register 3 Interrupt Priority Register 4 Interrupt Priority Register 5 Interrupt Priority Register 6 Interrupt Priority Register 7 Interrupt Priority Register 8 Interrupt Priority Register 9 Vector Base Address Register Fast Interrupt 0 Match Register Fast Interrupt 0 Vector Address Low Register Fast Interrupt 0 Vector Address High Register Fast Interrupt 1 Match Register Fast Interrupt 1 Vector Address Low Register Fast Interrupt 1 Vector Address High Register IRQ Pending Register 0 IRQ Pending Register 1 IRQ Pending Register 2 IRQ Pending Register 3 IRQ Pending Register 4 IRQ Pending Register 5 Reserved ICTL $1D Interrupt Control Register 5.6.30 Section Location 5.6.1 5.6.2 5.6.3 5.6.4 5.6.5 5.6.6 5.6.7 5.6.8 5.6.9 5.6.10 5.6.11 5.6.12 5.6.13 5.6.14 5.6.15 5.6.16 5.6.17 5.6.18 5.6.19 5.6.20 5.6.21 5.6.22 5.6.23 56F8335 Technical Data, Rev. 5 74 Freescale Semiconductor Preliminary Register Descriptions Add. Register Offset Name $0 $1 $2 $3 $4 $5 $6 $7 $8 $9 $A $B $C $D $E $F $10 $11 $12 $13 $14 $15 IPR0 IPR1 IPR2 IPR3 IPR4 IPR5 IPR6 IPR7 IPR8 IPR9 VBA FIM0 FIVAL0 FIVAH0 FIM1 FIVAL1 FIVAH1 IRQP0 IRQP1 IRQP2 IRQP3 IRQP4 R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W Reserved $1D ICTL R W 15 0 0 14 0 0 13 12 11 10 9 0 0 8 0 0 7 0 0 6 0 0 5 0 4 0 3 0 2 0 1 0 0 0 BKPT_U0 IPL 0 0 STPCNT IPL 0 0 RX_REG IPL 0 0 TX_REG IPL IRQB IPL FCBOFF IPL GPIOB IPL SCI1_XMIT IPL DEC0_XIRQ IPL TMRC2 IPL TMRA2 IPL ADCA_CC IPL TRBUF IPL IRQA IPL 0 0 FMCBE IPL GPIOD IPL SPI0_RCV IPL FMCC IPL GPIOE IPL SPI1_XMIT IPL FMERR IPL GPIOF IPL SPI1_RCV IPL SCI1_RCV IPL TMRD2 IPL TMRB2 IPL 0 0 LOCK IPL FCMSGBUF IPL 0 0 LVI IPL FCWKUP IPL 0 0 0 0 FCERR IPL GPIOA IPL SCI1_TIDL IPL 0 0 GPIOC IPL SPI0_XMIT IPL DEC0_HIRQ IPL TMRC1 IPL TMRA1 IPL ADCB_CC IPL DEC1_XIRQ IPL DEC1_HIRQ IPL TMRC0 IPL TMRA0 IPL SCI0_RCV IPL PWMA_F IPL 0 0 0 0 TMRD3 IPL TMRB3 IPL SCI0_RERR IPL PWMB_F IPL 0 0 0 SCI1_RERR IPL TMRD1 IPL TMRB1 IPL SCI0_TIDL IPL PWMB_RL IPL TMRD0 IPL TMRB0 IPL SCI0_XMIT IPL ADCA_ZC IPL TMRC3 IPL TMRA3 IPL ABCB_ZC IPL PWMA_RL IPL VECTOR BASE ADDRESS 0 0 0 0 0 FAST INTERRUPT 0 FAST INTERRUPT 0 VECTOR ADDRESS LOW 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FAST INTERRUPT 0 VECTOR ADDRESS HIGH FAST INTERRUPT 1 FAST INTERRUPT 1 VECTOR ADDRESS LOW 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FAST INTERRUPT 1 VECTOR ADDRESS HIGH 1 PENDING [16:2] PENDING [32:17] PENDING [48:33] PENDING [64:49] PENDING [80:65] $16 IRQP5 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 PENDING [81] INT IPIC VAB INT_DIS 1 IRQA IRQB STATE STATE IRQB EDG IRQA EDG = Reserved 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 75 Figure 5-2 ITCN Register Map Summary 5.6.1 Interrupt Priority Register 0 (IPR0) 15 0 Base + $0 Read Write RESET 14 0 13 12 11 10 9 0 8 0 7 0 6 0 5 0 4 0 3 0 2 0 1 0 0 0 BKPT_U0IPL 0 0 STPCNT IPL 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Figure 5-3 Interrupt Priority Register 0 (IPR0) 5.6.1.1 5.6.1.2 Reserved—Bits 15–14 EOnCE Breakpoint Unit 0 Interrupt Priority Level (BKPT_U0 IPL)— Bits13–12 This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing. This field is used to set the interrupt priority levels for IRQs. This IRQ is limited to priorities 1 through 3. It is disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 1 10 = IRQ is priority level 2 11 = IRQ is priority level 3 5.6.1.3 EOnCE Step Counter Interrupt Priority Level (STPCNT IPL)— Bits 11–10 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 1 through 3. It is disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 1 10 = IRQ is priority level 2 11 = IRQ is priority level 3 5.6.1.4 Reserved—Bits 9–0 This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing. 5.6.2 Interrupt Priority Register 1 (IPR1) Base + $1 Read Write RESET 0 0 0 0 0 0 0 0 0 0 15 0 14 0 13 0 12 0 11 0 10 0 9 0 8 0 7 0 6 0 5 4 3 2 1 0 RX_REG IPL 0 0 TX_REG IPL 0 0 TRBUF IPL 0 0 Figure 5-4 Interrupt Priority Register 1 (IPR1) 56F8335 Technical Data, Rev. 5 76 Freescale Semiconductor Preliminary Register Descriptions 5.6.2.1 5.6.2.2 Reserved—Bits 15–6 EOnCE Receive Register Full Interrupt Priority Level (RX_REG IPL)—Bits 5–4 This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing. This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 1 through 3. It is disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 1 10 = IRQ is priority level 2 11 = IRQ is priority level 3 5.6.2.3 EOnCE Transmit Register Empty Interrupt Priority Level (TX_REG IPL)—Bits 3–2 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 1 through 3. It is disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 1 10 = IRQ is priority level 2 11 = IRQ is priority level 3 5.6.2.4 EOnCE Trace Buffer Interrupt Priority Level (TRBUF IPL)— Bits 1–0 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 1 through 3. It is disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 1 10 = IRQ is priority level 2 11 = IRQ is priority level 3 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 77 5.6.3 Interrupt Priority Register 2 (IPR2) 15 14 13 12 11 10 9 8 7 6 5 0 Base + $2 Read Write RESET 4 0 3 2 1 0 FMCBE IPL 0 0 FMCC IPL 0 0 FMERR IPL 0 0 LOCK IPL 0 0 LVI IPL 0 0 IRQB IPL 0 0 IRQA IPL 0 0 0 0 Figure 5-5 Interrupt Priority Register 2 (IPR2) 5.6.3.1 Flash Memory Command, Data, Address Buffers Empty Interrupt Priority Level (FMCBE IPL)—Bits 15–14 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. It is disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.3.2 Flash Memory Command Complete Priority Level (FMCC IPL)— Bits 13–12 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. It is disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.3.3 Flash Memory Error Interrupt Priority Level (FMERR IPL)—Bits 11–10 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. It is disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.3.4 PLL Loss of Lock Interrupt Priority Level (LOCK IPL)—Bits 9–8 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. It is disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 56F8335 Technical Data, Rev. 5 78 Freescale Semiconductor Preliminary Register Descriptions 5.6.3.5 Low Voltage Detector Interrupt Priority Level (LVI IPL)—Bits 7–6 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. It is disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.3.6 5.6.3.7 Reserved—Bits 5–4 External IRQ B Interrupt Priority Level (IRQB IPL)—Bits 3–2 This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing. This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. It is disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.3.8 External IRQ A Interrupt Priority Level (IRQA IPL)—Bits 1–0 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. It is disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.4 Interrupt Priority Register 3 (IPR3) Base + $3 Read Write RESET 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 0 0 GPIOD IPL 0 0 GPIOE IPL 0 0 GPIOF IPL 0 0 FCMSGBUF IPL 0 0 FCWKUP IPL 0 0 FCERR IPL 0 0 FCBOFF IPL 0 0 0 0 Figure 5-6 Interrupt Priority Register 3 (IPR3) 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 79 5.6.4.1 GPIOD Interrupt Priority Level (GPIOD IPL)—Bits 15–14 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.4.2 GPIOE Interrupt Priority Level (GPIOE IPL)—Bits 13–12 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.4.3 GPIOF Interrupt Priority Level (GPIOF IPL)—Bits 11–10 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.4.4 FlexCAN Message Buffer Interrupt Priority Level (FCMSGBUF IPL)— Bits 9–8 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.4.5 FlexCAN Wake Up Interrupt Priority Level (FCWKUP IPL)—Bits 7–6 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 56F8335 Technical Data, Rev. 5 80 Freescale Semiconductor Preliminary Register Descriptions 5.6.4.6 FlexCAN Error Interrupt Priority Level (FCERR IPL)—Bits 5–4 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.4.7 FlexCAN Bus Off Interrupt Priority Level (FCBOFF IPL)—Bits 3–2 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.4.8 Reserved—Bits 1–0 This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing. 5.6.5 Interrupt Priority Register 4 (IPR4) 15 14 13 12 11 10 9 0 Base + $4 Read Write RESET 8 0 7 0 6 0 5 4 3 2 1 0 SPI0_RCV IPL 0 0 SPI1_XMIT IPL 0 0 SPI1_RCV IPL 0 0 GPIOA IPL 0 0 GPIOB IPL 0 0 GPIOC IPL 0 0 0 0 0 0 Figure 5-7 Interrupt Priority Register 4 (IPR4) 5.6.5.1 SPI 0 Receiver Full Interrupt Priority Level (SPI0_RCV IPL)— Bits 15–14 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 81 5.6.5.2 SPI 1 Transmit Empty Interrupt Priority Level (SPI1_XMIT IPL)— Bits 13–12 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.5.3 SPI 1 Receiver Full Interrupt Priority Level (SPI1_RCV IPL)— Bits 11–10 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.5.4 5.6.5.5 Reserved—Bits 9–6 GPIOA Interrupt Priority Level (GPIOA IPL)—Bits 5–4 This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing. This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.5.6 GPIOB Interrupt Priority Level (GPIOB IPL)—Bits 3–2 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.5.7 GPIOC Interrupt Priority Level (GPIOC IPL)—Bits 1–0 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. 56F8335 Technical Data, Rev. 5 82 Freescale Semiconductor Preliminary Register Descriptions • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.6 Interrupt Priority Register 5 (IPR5) 15 14 13 12 11 10 9 8 7 0 Base + $5 Read Write RESET 6 0 5 4 3 2 1 0 DEC1_XIRQ IPL 0 0 DEC1_HIRQ IPL 0 0 SCI1_RCV IPL 0 0 SCI1_RERR IPL 0 0 SCI1_TIDL IPL 0 0 SCI1_XMIT IPL 0 0 SPI0_XMIT IPL 0 0 0 0 Figure 5-8 Interrupt Priority Register 5 (IPR5) 5.6.6.1 Quadrature Decoder 1 INDEX Pulse Interrupt Priority Level (DEC1_XIRQ IPL)—Bits 15–14 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.6.2 Quadrature Decoder 1 HOME Signal Transition or Watchdog Timer Interrupt Priority Level (DEC1_HIRQ IPL)—Bits 13–12 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.6.3 SCI 1 Receiver Full Interrupt Priority Level (SCI1_RCV IPL)— Bits 11–10 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 83 • • 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.6.4 SCI 1 Receiver Error Interrupt Priority Level (SCI1_RERR IPL)— Bits 9–8 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.6.5 5.6.6.6 Reserved—Bits 7–6 SCI 1 Transmitter Idle Interrupt Priority Level (SCI1_TIDL IPL)— Bits 5–4 This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing. This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.6.7 SCI 1 Transmitter Empty Interrupt Priority Level (SCI1_XMIT IPL)— Bits 3–2 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.6.8 SPI 0 Transmitter Empty Interrupt Priority Level (SPI0_XMIT IPL)— Bits 1–0 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 56F8335 Technical Data, Rev. 5 84 Freescale Semiconductor Preliminary Register Descriptions 5.6.7 Interrupt Priority Register 6 (IPR6) 15 14 13 12 11 10 9 8 7 6 5 0 Base + $6 Read Write RESET 4 0 3 2 1 0 TMRC0 IPL 0 0 TMRD3 IPL 0 0 TMRD2 IPL 0 0 TMRD1 IPL 0 0 TMRD0 IPL 0 0 DEC0_XIRQ IPL 0 0 DEC0_HIRQ IPL 0 0 0 0 Figure 5-9 Interrupt Priority Register 6 (IPR6) 5.6.7.1 Timer C, Channel 0 Interrupt Priority Level (TMRC0 IPL)— Bits 15–14 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.7.2 Timer D, Channel 3 Interrupt Priority Level (TMRD3 IPL)— Bits 13–12 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.7.3 Timer D, Channel 2 Interrupt Priority Level (TMRD2 IPL)— Bits 11–10 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.7.4 Timer D, Channel 1 Interrupt Priority Level (TMRD1 IPL)— Bits 9–8 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. • 00 = IRQ disabled (default) 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 85 • • • 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.7.5 Timer D, Channel 0 Interrupt Priority Level (TMRD0 IPL)— Bits 7–6 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.7.6 5.6.7.7 Reserved—Bits 5–4 Quadrature Decoder 0, INDEX Pulse Interrupt Priority Level (DEC0_XIRQ IPL)—Bits 3–2 This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing. This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.7.8 Quadrature Decoder 0, HOME Signal Transition or Watchdog Timer Interrupt Priority Level (DEC0_HIRQ IPL)—Bits 1–0 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.8 Interrupt Priority Register 7 (IPR7) 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Read Write RESET Base + $7 TMRA0 IPL 0 0 TMRB3 IPL 0 0 TMRB2 IPL 0 0 TMRB1 IPL 0 0 TMRB0 IPL 0 0 TMRC3 IPL 0 0 TMRC2 IPL 0 0 TMRC1 IPL 0 0 Figure 5-10 Interrupt Priority Register (IPR7) 56F8335 Technical Data, Rev. 5 86 Freescale Semiconductor Preliminary Register Descriptions 5.6.8.1 Timer A, Channel 0 Interrupt Priority Level (TMRA0 IPL)—Bits 15–14 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.8.2 Timer B, Channel 3 Interrupt Priority Level (TMRB3 IPL)—Bits 13–12 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.8.3 Timer B, Channel 2 Interrupt Priority Level (TMRB2 IPL)—Bits 11–10 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.8.4 Timer B, Channel 1 Interrupt Priority Level (TMRB1 IPL)—Bits 9–8 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.8.5 Timer B, Channel 0 Interrupt Priority Level (TMRB0 IPL)—Bits 7–6 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 87 • 11 = IRQ is priority level 2 5.6.8.6 Timer C, Channel 3 Interrupt Priority Level (TMRC3 IPL)—Bits 5–4 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.8.7 Timer C, Channel 2 Interrupt Priority Level (TMRC2 IPL)—Bits 3–2 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.8.8 Timer C, Channel 1 Interrupt Priority Level (TMRC1 IPL)—Bits 1–0 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.9 Interrupt Priority Register 8 (IPR8) 15 14 13 12 11 0 Base + $8 Read Write RESET 10 0 9 8 7 6 5 4 3 2 1 0 SCI0_RCV IPL 0 0 SCI0_RERR IPL 0 0 SCI0_TIDL IPL 0 0 SCI0_XMIT IPL 0 0 TMRA3 IPL 0 0 TMRA2 IPL 0 0 TMRA1 IPL 0 0 0 0 Figure 5-11 Interrupt Priority Register 8 (IPR8) 5.6.9.1 SCI0 Receiver Full Interrupt Priority Level (SCI0_RCV IPL)—Bits 15–14 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 56F8335 Technical Data, Rev. 5 88 Freescale Semiconductor Preliminary Register Descriptions 5.6.9.2 SCI0 Receiver Error Interrupt Priority Level (SCI0_RERR IPL)— Bits 13–12 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.9.3 5.6.9.4 Reserved—Bits 11–10 SCI0 Transmitter Idle Interrupt Priority Level (SCI0_TIDL IPL)— Bits 9–8 This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing. This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.9.5 SCI0 Transmitter Empty Interrupt Priority Level (SCI0_XMIT IPL)— Bits 7–6 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.9.6 Timer A, Channel 3 Interrupt Priority Level (TMRA3 IPL)—Bits 5–4 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. • 00 = IRQ disabled (default) 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 89 • • • 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.9.7 Timer A, Channel 2 Interrupt Priority Level (TMRA2 IPL)—Bits 3–2 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.9.8 Timer A, Channel 1 Interrupt Priority Level (TMRA1 IPL)—Bits 1–0 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.10 Interrupt Priority Register 9 (IPR9) 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Read Write PWMA_RL IPL 0 0 PWMB_RL IPL 0 0 ADCA_CC IPL 0 0 ADCB_CC IPL 0 0 Base + $9 PWMA_F IPL 0 0 PWMB_F IPL 0 0 ADCA_ZC IPL ABCB_ZC IPL 0 0 0 0 RESET Figure 5-12 Interrupt Priority Register 9 (IPR9) 5.6.10.1 PWM A Fault Interrupt Priority Level (PWMA_F IPL)—Bits 15–14 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.10.2 PWM B Fault Interrupt Priority Level (PWMB_F IPL)—Bits 13–12 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. 56F8335 Technical Data, Rev. 5 90 Freescale Semiconductor Preliminary Register Descriptions • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.10.3 Reload PWM A Interrupt Priority Level (PWMA_RL IPL)—Bits 11–10 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.10.4 Reload PWM B Interrupt Priority Level (PWMB_RL IPL)—Bits 9–8 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.10.5 ADC A Zero Crossing or Limit Error Interrupt Priority Level (ADCA_ZC IPL)—Bits 7–6 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.10.6 ADC B Zero Crossing Interrupt Priority Level (ADCB_ZC IPL)— Bits 5–4 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 91 5.6.10.7 ADC A Conversion Complete Interrupt Priority Level (ADCA_CC IPL)—Bits 3–2 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.10.8 ADC B Conversion Complete Interrupt Priority Level (ADCB_CC IPL)—Bits 1–0 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. • • • • 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.11 Vector Base Address Register (VBA) 15 0 Base + $A Read Write RESET 14 0 13 0 12 11 10 9 8 7 6 5 4 3 2 1 0 VECTOR BASE ADDRESS 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Figure 5-13 Vector Base Address Register (VBA) 5.6.11.1 5.6.11.2 Reserved—Bits 15–13 Interrupt Vector Base Address (VECTOR BASE ADDRESS)— Bits 12–0 This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing. The contents of this register determine the location of the Vector Address Table. The value in this register is used as the upper 13 bits of the interrupt Vector Address Bus (VAB[20:0]). The lower eight bits are determined based upon the highest-priority interrupt. They are then appended onto VBA before presenting the full interrupt address to the 56800E core; see Part 5.3.1 for details. 56F8335 Technical Data, Rev. 5 92 Freescale Semiconductor Preliminary Register Descriptions 5.6.12 Fast Interrupt 0 Match Register (FIM0) 15 0 Base + $B Read Write RESET 14 0 13 0 12 0 11 0 10 0 9 0 8 0 7 0 6 5 4 3 2 1 0 FAST INTERRUPT 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Figure 5-14 Fast Interrupt 0 Match Register (FIM0) 5.6.12.1 5.6.12.2 Reserved—Bits 15–7 Fast Interrupt 0 Vector Number (FAST INTERRUPT 0)—Bits 6–0 This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing. This value determines which IRQ will be a Fast Interrupt 0. Fast interrupts vector directly to a service routine based on values in the Fast Interrupt Vector Address registers without having to go to a jump table first; see Part 5.3.3. IRQs used as fast interrupts must be set to priority level 2. Unexpected results will occur if a fast interrupt vector is set to any other priority. Fast interrupts automatically become the highest-priority level 2 interrupt, regardless of their location in the interrupt table, prior to being declared as fast interrupt. Fast Interrupt 0 has priority over Fast Interrupt 1. To determine the vector number of each IRQ, refer to Table 4-5. 5.6.13 Fast Interrupt 0 Vector Address Low Register (FIVAL0) 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Read Write FAST INTERRUPT 0 VECTOR ADDRESS LOW 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Base + $C RESET Figure 5-15 Fast Interrupt 0 Vector Address Low Register (FIVAL0) 5.6.13.1 Fast Interrupt 0 Vector Address Low (FIVAL0)—Bits 15–0 The lower 16 bits of the vector address used for Fast Interrupt 0. This register is combined with FIVAH0 to form the 21-bit vector address for Fast Interrupt 0 defined in the FIM0 register. 5.6.14 Fast Interrupt 0 Vector Address High Register (FIVAH0) 15 0 Base + $D Read Write RESET 14 0 13 0 12 0 11 0 10 0 9 0 8 0 7 0 6 0 5 0 4 3 2 1 0 FAST INTERRUPT 0 VECTOR ADDRESS HIGH 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Figure 5-16 Fast Interrupt 0 Vector Address High Register (FIVAH0) 5.6.14.1 Reserved—Bits 15–5 This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing. 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 93 5.6.14.2 Fast Interrupt 0 Vector Address High (FIVAH0)—Bits 4–0 The upper five bits of the vector address used for Fast Interrupt 0. This register is combined with FIVAL0 to form the 21-bit vector address for Fast Interrupt 0 defined in the FIM0 register. 5.6.15 Fast Interrupt 1 Match Register (FIM1) 15 0 Base + $E Read Write RESET 14 0 13 0 12 0 11 0 10 0 9 0 8 0 7 0 6 5 4 3 2 1 0 FAST INTERRUPT 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Figure 5-17 Fast Interrupt 1 Match Register (FIM1) 5.6.15.1 5.6.15.2 Reserved—Bits 15–7 Fast Interrupt 1 Vector Number (FAST INTERRUPT 1)—Bits 6–0 This bit field is reserved or not implemented. It is read as 0, but cannot be modified by writing. This value determines which IRQ will be a Fast Interrupt 1. Fast interrupts vector directly to a service routine based on values in the Fast Interrupt Vector Address registers without having to go to a jump table first; see Part 5.3.3. IRQs used as fast interrupts must be set to priority level 2. Unexpected results will occur if a fast interrupt vector is set to any other priority. Fast interrupts automatically become the highest-priority level 2 interrupt, regardless of their location in the interrupt table, prior to being declared as fast interrupt. Fast Interrupt 0 has priority over Fast Interrupt 1. To determine the vector number of each IRQ, refer to Table 4-5. 5.6.16 Fast Interrupt 1 Vector Address Low Register (FIVAL1) 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Read Write FAST INTERRUPT 1 VECTOR ADDRESS LOW 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Base + $F RESET Figure 5-18 Fast Interrupt 1 Vector Address Low Register (FIVAL1) 5.6.16.1 Fast Interrupt 1 Vector Address Low (FIVAL1)—Bits 15–0 The lower 16 bits of the vector address are used for Fast Interrupt 1. This register is combined with FIVAH1 to form the 21-bit vector address for Fast Interrupt 1 defined in the FIM1 register. 5.6.17 Fast Interrupt 1 Vector Address High Register (FIVAH1) 15 0 Base + $10 Read Write RESET 14 0 13 0 12 0 11 0 10 0 9 0 8 0 7 0 6 0 5 0 4 3 2 1 0 FAST INTERRUPT 1 VECTOR ADDRESS HIGH 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Figure 5-19 Fast Interrupt 1 Vector Address High Register (FIVAH1) 56F8335 Technical Data, Rev. 5 94 Freescale Semiconductor Preliminary Register Descriptions 5.6.17.1 5.6.17.2 Reserved—Bits 15–5 Fast Interrupt 1 Vector Address High (FIVAH1)—Bits 4–0 This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing. The upper five bits of the vector address are used for Fast Interrupt 1. This register is combined with FIVAL1 to form the 21-bit vector address for Fast Interrupt 1 defined in the FIM1 register. 5.6.18 IRQ Pending 0 Register (IRQP0) 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 1 Base + $11 Read Write RESET PENDING [16:2] 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Figure 5-20 IRQ Pending 0 Register (IRQP0) 5.6.18.1 IRQ Pending (PENDING)—Bits 16–2 This register combines with the other five to represent the pending IRQs for interrupt vector numbers 2 through 81. • • 0 = IRQ pending for this vector number 1 = No IRQ pending for this vector number 5.6.18.2 Reserved—Bit 0 This bit is reserved or not implemented. It is read as 1 and cannot be modified by writing. 5.6.19 IRQ Pending 1 Register (IRQP1) 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Read Write PENDING [32:17] $Base + $12 RESET 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Figure 5-21 IRQ Pending 1 Register (IRQP1) 5.6.19.1 IRQ Pending (PENDING)—Bits 32–17 This register combines with the other five to represent the pending IRQs for interrupt vector numbers 2 through 81. • • 0 = IRQ pending for this vector number 1 = No IRQ pending for this vector number 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 95 5.6.20 IRQ Pending 2 Register (IRQP2) 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Read Write PENDING [48:33] Base + $13 RESET 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Figure 5-22 IRQ Pending 2 Register (IRQP2) 5.6.20.1 IRQ Pending (PENDING)—Bits 48–33 This register combines with the other five to represent the pending IRQs for interrupt vector numbers 2 through 81. • • 0 = IRQ pending for this vector number 1 = No IRQ pending for this vector number 5.6.21 IRQ Pending 3 Register (IRQP3) 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Read Write PENDING [64:49] Base + $14 RESET 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Figure 5-23 IRQ Pending 3 Register (IRQP3) 5.6.21.1 IRQ Pending (PENDING)—Bits 64–49 This register combines with the other five to represent the pending IRQs for interrupt vector numbers 2 through 81. • • 0 = IRQ pending for this vector number 1 = No IRQ pending for this vector number 5.6.22 IRQ Pending 4 Register (IRQP4) 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Read Write PENDING [80:65] Base + $15 RESET 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Figure 5-24 IRQ Pending 4 Register (IRQP4) 5.6.22.1 IRQ Pending (PENDING)—Bits 80–65 This register combines with the other five to represent the pending IRQs for interrupt vector numbers 2 through 81. • 0 = IRQ pending for this vector number 56F8335 Technical Data, Rev. 5 96 Freescale Semiconductor Preliminary Register Descriptions • 1 = No IRQ pending for this vector number 5.6.23 IRQ Pending 5 Register (IRQP5) 15 1 Base + $16 Read Write RESET 14 1 13 1 12 1 11 1 10 1 9 1 8 1 7 1 6 1 5 1 4 1 3 1 2 1 1 1 0 PENDING [81] 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Figure 5-25 IRQ Pending Register 5 (IRQP5) 5.6.23.1 5.6.23.2 Reserved—Bits 96–82 IRQ Pending (PENDING)—Bit 81 This bit field is reserved or not implemented. The bits are read as 1 and cannot be modified by writing. This register combines with the other five to represent the pending IRQs for interrupt vector numbers 2 through 81. • • 0 = IRQ pending for this vector number 1 = No IRQ pending for this vector number 5.6.24 5.6.25 5.6.26 5.6.27 5.6.28 5.6.29 Reserved—Base + 17 Reserved—Base + 18 Reserved—Base + 19 Reserved—Base + 1A Reserved—Base + 1B Reserved—Base + 1C 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 97 5.6.30 ITCN Control Register (ICTL) 15 INT Base + $1D Read Write RESET 14 IPIC 13 12 11 10 9 VAB 8 7 6 5 INT_DIS 4 1 3 IRQB STATE 2 IRQA STATE 1 IRQB EDG 0 0 IRQA EDG 0 0 0 0 1 0 0 0 0 0 0 0 1 1 1 Figure 5-26 ITCN Control Register (ICTL) 5.6.30.1 • • Interrupt (INT)—Bit 15 This read-only bit reflects the state of the interrupt to the 56800E core. 0 = No interrupt is being sent to the 56800E core 1 = An interrupt is being sent to the 56800E core 5.6.30.2 Interrupt Priority Level (IPIC)—Bits 14–13 These read-only bits reflect the state of the new interrupt priority level bits being presented to the 56800E core at the time the last IRQ was taken. This field is only updated when the 56800E core jumps to a new interrupt service routine. Note: • • • • Nested interrupts may cause this field to be updated before the original interrupt service routine can read it. 00 = Required nested exception priority levels are 0, 1, 2, or 3 01 = Required nested exception priority levels are 1, 2, or 3 10 = Required nested exception priority levels are 2 or 3 11 = Required nested exception priority level is 3 5.6.30.3 Vector Number - Vector Address Bus (VAB)—Bits 12–6 This read-only field shows the vector number (VAB[7:1]) used at the time the last IRQ was taken. This field is only updated when the 56800E core jumps to a new interrupt service routine. Note: Nested interrupts may cause this field to be updated before the original interrupt service routine can read it. 5.6.30.4 • • Interrupt Disable (INT_DIS)—Bit 5 This bit allows all interrupts to be disabled. 0 = Normal operation (default) 1 = All interrupts disabled 5.6.30.5 Reserved—Bit 4 This bit field is reserved or not implemented. It is read as 1 and cannot be modified by writing. 56F8335 Technical Data, Rev. 5 98 Freescale Semiconductor Preliminary Resets 5.6.30.6 5.6.30.7 5.6.30.8 IRQB State Pin (IRQB STATE)—Bit 3 IRQA State Pin (IRQA STATE)—Bit 2 IRQB Edge Pin (IRQB Edg)—Bit 1 This read-only bit reflects the state of the external IRQB pin. This read-only bit reflects the state of the external IRQA pin. This bit controls whether the external IRQB interrupt is edge- or level-sensitive. During Stop and Wait modes, it is automatically level-sensitive. • • 0 = IRQB interrupt is a low-level sensitive (default) 1 = IRQB interrupt is falling-edge sensitive. 5.6.30.9 IRQA Edge Pin (IRQA Edg)—Bit 0 This bit controls whether the external IRQA interrupt is edge- or level-sensitive. During Stop and Wait modes, it is automatically level-sensitive. • • 0 = IRQA interrupt is a low-level sensitive (default) 1 = IRQA interrupt is falling-edge sensitive. 5.7 Resets 5.7.1 Reset Handshake Timing The ITCN provides the 56800E core with a reset vector address whenever RESET is asserted. The reset vector will be presented until the second rising clock edge after RESET is released. 5.7.2 ITCN After Reset After reset, all of the ITCN registers are in their default states. This means all interrupts are disabled except the core IRQs with fixed priorities: • • • • • • • • Illegal Instruction SW Interrupt 3 HW Stack Overflow Misaligned Long Word Access SW Interrupt 2 SW Interrupt 1 SW Interrupt 0 SW Interrupt LP These interrupts are enabled at their fixed priority levels. 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 99 Part 6 System Integration Module (SIM) 6.1 Introduction The SIM module is a system catchall for the glue logic that ties together the system-on-chip. It controls distribution of resets and clocks and provides a number of control features. The system integration module is responsible for the following functions: • • • • • • • Reset sequencing Clock generation & distribution Stop/Wait control Pull-up enables for selected peripherals System status registers Registers for software access to the JTAG ID of the chip Enforcing Flash security These are discussed in more detail in the sections that follow. 6.2 Features The SIM has the following features: • • • Flash security feature prevents unauthorized access to code/data contained in on-chip Flash memory Power-saving clock gating for peripheral Three power modes (Run, Wait, Stop) to control power utilization — Stop mode shuts down the 56800E core, system clock, peripheral clock, and PLL operation — Stop mode entry can optionally disable PLL and Oscillator (low power vs. fast restart); must be done explicitly — Wait mode shuts down the 56800E core and unnecessary system clock operation — Run mode supports full part operation • • • • • • • Controls to enable/disable the 56800E core WAIT and STOP instructions Calculates base delay for reset extension based upon POR or RESET operations. Reset delay will be 3 x 32 clocks (phased release of reset) for reset, except for POR, which is 221 clock cycles. Controls reset sequencing after reset Software-initiated reset Four 16-bit registers reset only by a Power-On Reset usable for general-purpose software control System Control Register Registers for software access to the JTAG ID of the chip 56F8335 Technical Data, Rev. 5 100 Freescale Semiconductor Preliminary Operating Modes 6.3 Operating Modes Since the SIM is responsible for distributing clocks and resets across the chip, it must understand the various chip operating modes and take appropriate action. These are: • Reset Mode, which has two submodes: — POR and RESET operation The 56800E core and all peripherals are reset. This occurs when the internal POR is asserted or the RESET pin is asserted. — COP reset and software reset operation The 56800E core and all peripherals are reset. The MA bit within the OMR is not changed. This allows the software to determine the boot mode (internal or external boot) to be used on the next reset. • • Run Mode This is the primary mode of operation for this device. In this mode, the 56800E controls chip operation. Debug Mode The 56800E is controlled via JTAG/EOnCE when in debug mode. All peripherals, except the COP and PWMs, continue to run. COP is disabled and PWM outputs are optionally switched off to disable any motor from being driven; see the PWM chapter in the 56F8300 Peripheral User Manual for details. Wait Mode In Wait mode, the core clock and memory clocks are disabled. Optionally, the COP can be stopped. Similarly, it is an option to switch off PWM outputs to disable any motor from being driven. All other peripherals continue to run. Stop Mode When in Stop mode, the 56800E core, memory and most peripheral clocks are shut down. Optionally, the COP and CAN can be stopped. For lowest power consumption in Stop mode, the PLL can be shut down. This must be done explicitly before entering Stop mode, since there is no automatic mechanism for this. The CAN (along with any non-gated interrupt) is capable of waking the chip up from Stop mode, but is not fully functional in Stop mode. • • 6.4 Operating Mode Register Bit 15 NL 14 13 12 11 10 9 8 CM R/W 7 XP R/W 0 6 SD R/W 0 5 R R/W 0 4 SA R/W 0 3 EX R/W 0 2 0 1 MB R/W 0 MA R/W X Type RESET R/W 0 0 0 0 0 0 0 0 0 X Figure 6-1 OMR The reset state for MB and MA will depend on the Flash secured state. See Part 4.2 and Part 7 for detailed information on how the Operating Mode Register (OMR) MA and MB bits operate in this device. For additional information on the EX bit, see Part 4.4. For all other bits, see the DSP56F800E Reference Manual. Note: The OMR is not a Memory Map register; it is directly accessible in code through the acronym OMR. 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 101 6.5 Register Descriptions Table 6-1 SIM Registers (SIM_BASE = $00 F350) Address Offset Base + $0 Base + $1 Base + $2 Base + $3 Base + $4 Base + $5 Base + $6 Base + $7 Base + $8 Address Acronym SIM_CONTROL SIM_RSTSTS SIM_SCR0 SIM_SCR1 SIM_SCR2 SIM_SCR3 SIM_MSH_ID SIM_LSH_ID SIM_PUDR Register Name Control Register Reset Status Register Software Control Register 0 Software Control Register 1 Software Control Register 2 Software Control Register 3 Most Significant Half of JTAG ID Least Significant Half of JTAG ID Pull-up Disable Register Reserved Base + $A Base + $B Base + $C Base + $D Base + $E SIM_CLKOSR SIM_GPS SIM_PCE SIM_ISALH SIM_ISALL CLKO Select Register GPIO Peripheral Select Register Peripheral Clock Enable Register I/O Short Address Location High Register I/O Short Address Location Low Register 6.5.7 6.5.8 6.5.9 6.5.10 6.5.10 Section Location 6.5.1 6.5.2 6.5.3 6.5.3 6.5.3 6.5.3 6.5.4 6.5.5 6.5.6 56F8335 Technical Data, Rev. 5 102 Freescale Semiconductor Preliminary Register Descriptions Add. Offset $0 $1 $2 $3 $4 $5 $6 $7 $8 Register Name SIM_ CONTROL SIM_ RSTSTS SIM_SCR0 SIM_SCR1 SIM_SCR2 SIM_SCR3 SIM_MSH_ ID SIM_LSH_ID SIM_PUDR Reserved R W R W R W R W R W R W R W R W R W R W R W R W R W R W 15 0 0 14 0 0 13 0 0 12 0 0 11 0 0 10 0 0 9 0 0 8 0 0 7 0 0 6 0 0 5 ONCE EBL0 SWR 4 SW RST COPR 3 2 1 0 STOP_ DISABLE EXTR POR WAIT_ DISABLE 0 0 FIELD FIELD FIELD FIELD 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 1 0 1 0 1 0 0 1 0 1 1 0 0 1 1 1 0 0 0 0 0 1 0 PWMA1 CAN EMI_ RESET MODE 0 0 0 0 IRQ XBOOT PWMB PWMA0 CTRL JTAG $A $B $C $D $E SIM_ CLKOSR SIM_GPS SIM_PCE SIM_ISALH SIM_ISALL 0 0 0 0 0 0 0 0 A23 0 A22 0 A21 0 A20 0 CLKDIS 0 0 C3 SPI1 1 CLKOSEL C2 SPI0 1 C1 C0 EMI 1 ADCB 1 ADCA 1 CAN 1 DEC1 1 DEC 0 1 TMRD 1 TMRC 1 TMRB 1 TMRA 1 SCI1 1 SCI0 1 PWMB PWMA ISAL[23:22] ISAL[21:6] = Reserved Figure 6-2 SIM Register Map Summary 6.5.1 SIM Control Register (SIM_CONTROL) 15 0 Base + $0 Read Write RESET 14 0 13 0 12 0 11 0 10 0 9 0 8 0 7 0 6 0 5 ONCE EBL 0 4 SW RST 0 3 2 1 0 STOP_ DISABLE 0 0 WAIT_ DISABLE 0 0 0 0 0 0 0 0 0 0 0 0 Figure 6-3 SIM Control Register (SIM_CONTROL) 6.5.1.1 6.5.1.2 • • Reserved—Bits 15–6 OnCE Enable (OnCE EBL)—Bit 5 This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing. 0 = OnCE clock to 56800E core enabled when core TAP is enabled 1 = OnCE clock to 56800E core is always enabled 6.5.1.3 Software Reset (SW RST)—Bit 4 This bit is always read as 0. Writing 1 to this field will cause the part to reset. 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 103 6.5.1.4 • • • • Stop Disable (STOP_DISABLE)—Bits 3–2 00 = Stop mode will be entered when the 56800E core executes a STOP instruction 01 = The 56800E STOP instruction will not cause entry into Stop mode; STOP_DISABLE can be reprogrammed in the future 10 = The 56800E STOP instruction will not cause entry into Stop mode; STOP_DISABLE can then only be changed by resetting the device 11 = Same operation as 10 6.5.1.5 • • • • Wait Disable (WAIT_DISABLE)—Bits 1–0 00 = Wait mode will be entered when the 56800E core executes a WAIT instruction 01 = The 56800E WAIT instruction will not cause entry into Wait mode; WAIT_DISABLE can be reprogrammed in the future 10 = The 56800E WAIT instruction will not cause entry into Wait mode; WAIT_DISABLE can then only be changed by resetting the device 11 = Same operation as 10 6.5.2 SIM Reset Status Register (SIM_RSTSTS) Bits in this register are set upon any system reset and are initialized only by a Power-On Reset (POR). A reset (other than POR) will only set bits in the register; bits are not cleared. Only software should clear this register. Base + $1 Read Write RESET 0 0 0 0 0 0 0 0 0 0 15 0 14 0 13 0 12 0 11 0 10 0 9 0 8 0 7 0 6 0 5 SWR 4 COPR 3 EXTR 2 POR 1 0 0 0 0 0 Figure 6-4 SIM Reset Status Register (SIM_RSTSTS) 6.5.2.1 6.5.2.2 Reserved—Bits 15–6 Software Reset (SWR)—Bit 5 This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing. When 1, this bit indicates that the previous reset occurred as a result of a software reset (write to SW RST bit in the SIM_CONTROL register). This bit will be cleared by any hardware reset or by software. Writing a 0 to this bit position will set the bit, while writing a 1 to the bit will clear it. 6.5.2.3 COP Reset (COPR)—Bit 4 When 1, the COPR bit indicates the Computer Operating Properly (COP) timer-generated reset has occurred. This bit will be cleared by a Power-On Reset or by software. Writing a 0 to this bit position will set the bit, while writing a 1 to the bit will clear it. 6.5.2.4 External Reset (EXTR)—Bit 3 If 1, the EXTR bit indicates an external system reset has occurred. This bit will be cleared by a Power-On Reset or by software. Writing a 0 to this bit position will set the bit, while writing a 1 to the bit position 56F8335 Technical Data, Rev. 5 104 Freescale Semiconductor Preliminary Register Descriptions will clear it. Basically, when the EXTR bit is 1, the previous system reset was caused by the external RESET pin being asserted low. 6.5.2.5 Power-On Reset (POR)—Bit 2 When 1, the POR bit indicates a Power-On Reset occurred some time in the past. This bit can be cleared only by software or by another type of reset. Writing a 0 to this bit will set the bit, while writing a 1 to the bit position will clear the bit. In summary, if the bit is 1, the previous system reset was due to a Power-On Reset. 6.5.2.6 Reserved—Bits 1–0 This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing. 6.5.3 SIM Software Control Registers (SIM_SCR0, SIM_SCR1, SIM_SCR2, and SIM_SCR3) Only SIM_SCR0 is shown in this section. SIM_SCR1, SIM_SCR2, and SIM_SCR3 are identical in functionality. Base + $2 Read Write POR 15 14 13 12 11 10 9 8 FIELD 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Figure 6-5 SIM Software Control Register 0 (SIM_SCR0) 6.5.3.1 Software Control Data 1 (FIELD)—Bits 15–0 This register is reset only by the Power-On Reset (POR). It has no part-specific functionality and is intended for use by a software developer to contain data that will be unaffected by the other reset sources (RESET pin, software reset, and COP reset). 6.5.4 Most Significant Half of JTAG ID (SIM_MSH_ID) This read-only register displays the most significant half of the JTAG ID for the chip. This register reads $01F4. Base + $6 Read Write RESET 0 0 0 0 0 0 0 1 1 1 1 1 0 1 0 0 15 0 14 0 13 0 12 0 11 0 10 0 9 0 8 1 7 1 6 1 5 1 4 1 3 0 2 1 1 0 0 0 Figure 6-6 Most Significant Half of JTAG ID (SIM_MSH_ID) 6.5.5 Least Significant Half of JTAG ID (SIM_LSH_ID) This read-only register displays the least significant half of the JTAG ID for the chip. This register reads $401D. 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 105 Base + $7 Read Write RESET 15 0 14 1 13 0 12 0 11 0 10 0 9 0 8 0 7 0 6 0 5 0 4 1 3 1 2 1 1 0 0 1 0 1 0 0 0 0 0 0 0 0 0 1 1 1 0 1 Figure 6-7 Least Significant Half of JTAG ID (SIM_LSH_ID) 6.5.6 SIM Pull-up Disable Register (SIM_PUDR) Most of the pins on the chip have on-chip pull-up resistors. Pins which can operate as GPIO can have these resistors disabled via the GPIO function. Non-GPIO pins can have their pull-ups disabled by setting the appropriate bit in this register. Disabling pull-ups is done on a peripheral-by-peripheral basis (for pins not muxed with GPIO). Each bit in the register (see Figure 6-8) corresponds to a functional group of pins. See Table 2-2 to identify which pins can deactivate the internal pull-up resistor. Base + $8 Read Write RESET 15 0 14 PWMA1 0 13 CAN 0 12 EMI_ MODE 0 11 RESET 0 10 IRQ 0 9 XBOOT 0 8 7 6 0 5 CTRL 0 4 0 3 JTAG 0 2 0 1 0 0 0 PWMB PWMA0 0 0 0 0 0 0 0 0 Figure 6-8 SIM Pull-up Disable Register (SIM_PUDR) 6.5.6.1 6.5.6.2 6.5.6.3 Reserved—Bit 15 PWMA1—Bit 14 This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing. This bit controls the pull-up resistors on the FAULTA3 pin. This bit controls the pull-up resistors on the CAN_RX pin. CAN—Bit 13 6.5.6.4 Note: This bit controls the pull-up resistors on the EMI_MODE pin. In this package, this input pin is double-bonded with the adjacent VSS pin and this bit should be changed to a 1 in order to reduce power consumption. EMI_MODE—Bit 12 6.5.6.5 6.5.6.6 RESET—Bit 11 IRQ—Bit 10 This bit controls the pull-up resistors on the RESET pin. This bit controls the pull-up resistors on the IRQA and IRQB pins. 56F8335 Technical Data, Rev. 5 106 Freescale Semiconductor Preliminary Register Descriptions 6.5.6.7 Note: This bit controls the pull-up resistors on the EXTBOOT pin. In this package, this input pin is double-bonded with the adjacent VSS pin and this bit should be changed to a 1 in order to reduce power consumption. XBOOT—Bit 9 6.5.6.8 This bit controls the pull-up resistors on the FAULTB0, FAULTB1, FAULTB2, and FAULTB3 pins. PWMB—Bit 8 6.5.6.9 This bit controls the pull-up resistors on the FAULTA0, FAULTA1, and FAULTA2 pins. PWMA0—Bit 7 6.5.6.10 6.5.6.11 6.5.6.12 6.5.6.13 Reserved—Bit 6 CTRL—Bit 5 This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing. This bit controls the pull-up resistors on the WR and RD pins. Reserved—Bit 4 JTAG—Bit 3 This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing. This bit controls the pull-up resistors on the TRST, TMS and TDI pins. 6.5.6.14 Reserved—Bit 2–0 This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing. 6.5.7 CLKO Select Register (SIM_CLKOSR) The CLKO select register can be used to multiplex out any one of the clocks generated inside the clock generation and SIM modules. The default value is SYS_CLK. This path has been optimized in order to minimize any delay and clock duty cycle distortion. All other clocks primarily muxed out are for test purposes only, and are subject to significant phase shift at high frequencies. The upper four bits of the GPIOB register can function as GPIO, [A23:A20], or as additional clock output signals. GPIO has priority and is enabled/disabled via the GPIOB_PER. If GPIOB[7:4] are programmed to operate as peripheral outputs, then the choice between [A23:A20] and additional clock outputs is done here in the CLKOSR. The default state is for the peripheral function of GPIOB[7:4] to be programmed as [A23:A20]. This can be changed by altering [A23:A20], as shown in Figure 6-9. Base + $A Read Write RESET 15 0 14 0 13 0 12 0 11 0 10 0 9 A23 0 8 A22 0 7 A21 0 6 A20 0 5 CLK DIS 1 4 3 2 CLKOSEL 1 0 0 0 0 0 0 0 0 0 0 0 0 Figure 6-9 CLKO Select Register (SIM_CLKOSR) 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 107 6.5.7.1 6.5.7.2 • • Reserved—Bits 15–10 Alternate GPIO_B Peripheral Function for A23 (A23)—Bit 9 This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing. 0 = Peripheral output function of GPIOB[7] is defined to be A[23] 1 = Peripheral output function of GPIOB[7] is defined to be the oscillator clock (MSTR_OSC, see Figure 3-4) 6.5.7.3 • • Alternate GPIO_B Peripheral Function for A22 (A22)—Bit 8 0 = Peripheral output function of GPIOB[6] is defined to be A[22] 1 = Peripheral output function of GPIOB[6] is defined to be SYS_CLK2 6.5.7.4 • • Alternate GPIO_B Peripheral Function for A21 (A21)—Bit 7 0 = Peripheral output function of GPIOB[5] is defined to be A[21] 1 = Peripheral output function of GPIOB[5] is defined to be SYS_CLK 6.5.7.5 • • Alternate GPIO_B Peripheral Function for A20 (A20)—Bit 6 0 = Peripheral output function of GPIOB[4] is defined to be A[20] 1 = Peripheral output function of GPIOB[4] is defined to be the prescaler clock (FREF, see Figure 3-4) 6.5.7.6 • • Clockout Disable (CLKDIS)—Bit 5 0 = CLKOUT output is enabled and will output the signal indicated by CLKOSEL 1 = CLKOUT is tri-stated 6.5.7.7 • • • • • • • • • • • • • • CLockout Select (CLKOSEL)—Bits 4–0 Selects clock to be muxed out on the CLKO pin. 00000 = SYS_CLK (from OCCS - DEFAULT) 00001 = Reserved for factory test—56800E clock 00010 = Reserved for factory test—XRAM clock 00011 = Reserved for factory test—PFLASH odd clock 00100 = Reserved for factory test—PFLASH even clock 00101 = Reserved for factory test—BFLASH clock 00110 = Reserved for factory test—DFLASH clock 00111 = Oscillator output 01000 = Fout (from OCCS) 01001 = Reserved for factory test—IPB clock 01010 = Reserved for factory test—Feedback (from OCCS, this is path to PLL) 01011 = Reserved for factory test—Prescaler clock (from OCCS) 01100 = Reserved for factory test—Postscaler clock (from OCCS) 01101 = Reserved for factory test—SYS_CLK2 (from OCCS) 56F8335 Technical Data, Rev. 5 108 Freescale Semiconductor Preliminary Register Descriptions • • • • 01110 = Reserved for factory test—SYS_CLK_DIV2 01111 = Reserved for factory test—SYS_CLK_D 10000 = ADCA clock 10001 = ADCB clock 6.5.8 GPIO Peripheral Select Register (SIM_GPS) The GPIO Peripheral Select Register can be used to multiplex out any one of the three alternate peripherals for GPIOC. The default peripheral is Quad Decoder 1 and Quad Timer B (NOT available in the 56F8135 device); these peripherals work together. The four I/O pins associated with GPIOC can function as GPIO, Quad Decoder 1/Quad Timer B, or as SPI 1 signals. GPIO is not the default and is enabled/disabled via the GPIOC_PER, as shown in Figure 6-10 and Table 6-2. When GPIOC[3:0] are programmed to operate as peripheral I/O, then the choice between decoder/timer and SPI inputs/outputs is made in the SIM_GPS and in conjunction with the Quad Timer Status and Control Registers (SCR). The default state is for the peripheral function of GPIOC[3:0] to be programmed as decoder functions. This can be changed by altering the appropriate controls in the indicated registers. GPIOC_PER Register GPIO Controlled 0 I/O Pad Control 1 SIM_ GPS Register Quad Timer Controlled 0 SPI Controlled 1 Figure 6-10 Overall Control of Pads Using SIM_GPS Control Table 6-2 Control of Pads Using SIM_GPS Control 1 Control Registers Pin Function Quad Timer SCR Register OEN bits GPIOC_DTR GPIOC_PER SIM_GPS Comments GPIO Input GPIO Output 0 0 0 1 — — — — 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 109 Table 6-2 Control of Pads Using SIM_GPS Control 1 Control Registers Pin Function Quad Timer SCR Register OEN bits GPIOC_PER GPIOC_DTR SIM_GPS Comments Quad Timer Input / Quad Decoder Input 2 Quad Timer Output / Quad Decoder Input 3 SPI input SPI output 1 — 0 0 1 — 0 1 See the “Switch Matrix for Inputs to the Timer” table in the 56F8300 Peripheral User Manual for the definition of timer inputs based on the Quad Decoder mode configuration. 1 1 — — 1 1 — — See SPI controls for determining the direction of each of the SPI pins. 1. This applies to the four pins that serve as Quad Decoder / Quad Timer / SPI / GPIOC functions. A separate set of control bits is used for each pin. 2. Reset configuration 3. Quad Decoder pins are always inputs and function in conjunction with the Quad Timer pins. Base + $B Read Write RESET 15 0 14 0 13 0 12 0 11 0 10 0 9 0 8 0 7 0 6 0 5 0 4 0 3 C3 0 2 C2 0 1 C1 0 0 C0 0 0 0 0 0 0 0 0 0 0 0 0 0 Figure 6-11 GPIO Peripheral Select Register (SIM_GPS) 6.5.8.1 6.5.8.2 • • Reserved—Bits 15–4 GPIOC3 (C3)—Bit 3 This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing. This bit selects the alternate function for GPIOC3. 0 = HOME1/TB3 (default - see “Switch Matrix Mode” bits of the Quad Decoder DECCR register in the 56F8300 Peripheral User’s Manual) 1 = SS1 6.5.8.3 • • GPIOC2 (C2)—Bit 2 This bit selects the alternate function for GPIOC2. 0 = INDEX1/TB2 (default) 1 = MISO1 6.5.8.4 GPIOC1 (C1)—Bit 1 This bit selects the alternate function for GPIOC1. 56F8335 Technical Data, Rev. 5 110 Freescale Semiconductor Preliminary Register Descriptions • • 0 = PHASEB1/TB1 (default) 1 = MOSI1 6.5.8.5 • • GPIOC0 (C0)—Bit 0 This bit selects the alternate function for GPIOC0. 0 = PHASEA1/TB0 (default) 1 = SCLK1 6.5.9 Peripheral Clock Enable Register (SIM_PCE) The Peripheral Clock Enable register is used to enable or disable clocks to the peripherals as a power savings feature. The clocks can be individually controlled for each peripheral on the chip. Base + $C Read Write RESET 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 15 EMI 14 13 12 11 10 9 TMRD 8 TMRC 7 6 5 SCI1 4 SCI0 3 SPI1 2 SPI0 1 0 ADCB ADCA CAN DEC1 DEC0 TMRB TMRA PWMB PWMA Figure 6-12 Peripheral Clock Enable Register (SIM_PCE) 6.5.9.1 • • External Memory Interface Enable (EMI)—Bit 15 Each bit controls clocks to the indicated peripheral. 1 = Clocks are enabled 0 = The clock is not provided to the peripheral (the peripheral is disabled) 6.5.9.2 • • Analog-to-Digital Converter B Enable (ADCB)—Bit 14 Each bit controls clocks to the indicated peripheral. 1 = Clocks are enabled 0 = The clock is not provided to the peripheral (the peripheral is disabled) 6.5.9.3 • • Analog-to-Digital Converter A Enable (ADCA)—Bit 13 Each bit controls clocks to the indicated peripheral. 1 = Clocks are enabled 0 = The clock is not provided to the peripheral (the peripheral is disabled) 6.5.9.4 • • FlexCAN Enable (CAN)—Bit 12 Each bit controls clocks to the indicated peripheral. 1 = Clocks are enabled 0 = The clock is not provided to the peripheral (the peripheral is disabled) 6.5.9.5 Decoder 1 Enable (DEC1)—Bit 11 Each bit controls clocks to the indicated peripheral. 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 111 • • 1 = Clocks are enabled 0 = The clock is not provided to the peripheral (the peripheral is disabled) 6.5.9.6 • • Decoder 0 Enable (DEC0)—Bit 10 Each bit controls clocks to the indicated peripheral. 1 = Clocks are enabled 0 = The clock is not provided to the peripheral (the peripheral is disabled) 6.5.9.7 • • Quad Timer D Enable (TMRD)—Bit 9 Each bit controls clocks to the indicated peripheral. 1 = Clocks are enabled 0 = The clock is not provided to the peripheral (the peripheral is disabled) 6.5.9.8 • • Quad Timer C Enable (TMRC)—Bit 8 Each bit controls clocks to the indicated peripheral. 1 = Clocks are enabled 0 = The clock is not provided to the peripheral (the peripheral is disabled) 6.5.9.9 • • Quad Timer B Enable (TMRB)—Bit 7 Each bit controls clocks to the indicated peripheral. 1 = Clocks are enabled 0 = The clock is not provided to the peripheral (the peripheral is disabled) 6.5.9.10 • • Quad Timer A Enable (TMRA)—Bit 6 Each bit controls clocks to the indicated peripheral. 1 = Clocks are enabled 0 = The clock is not provided to the peripheral (the peripheral is disabled) 6.5.9.11 • • Serial Communications Interface 1 Enable (SCI1)—Bit 5 Each bit controls clocks to the indicated peripheral. 1 = Clocks are enabled 0 = The clock is not provided to the peripheral (the peripheral is disabled) 6.5.9.12 • • Serial Communications Interface 0 Enable (SCI0)—Bit 4 Each bit controls clocks to the indicated peripheral. 1 = Clocks are enabled 0 = The clock is not provided to the peripheral (the peripheral is disabled) 6.5.9.13 Serial Peripheral Interface 1 Enable (SPI1)—Bit 3 Each bit controls clocks to the indicated peripheral. 56F8335 Technical Data, Rev. 5 112 Freescale Semiconductor Preliminary Register Descriptions • • 1 = Clocks are enabled 0 = The clock is not provided to the peripheral (the peripheral is disabled) 6.5.9.14 • • Serial Peripheral Interface 0 Enable (SPI0)—Bit 2 Each bit controls clocks to the indicated peripheral. 1 = Clocks are enabled 0 = The clock is not provided to the peripheral (the peripheral is disabled) 6.5.9.15 • • Pulse Width Modulator B Enable (PWMB)—Bit 1 Each bit controls clocks to the indicated peripheral. 1 = Clocks are enabled 0 = The clock is not provided to the peripheral (the peripheral is disabled) 6.5.9.16 • • Pulse Width Modulator A Enable (PWMA)—Bit 0 Each bit controls clocks to the indicated peripheral. 1 = Clocks are enabled 0 = The clock is not provided to the peripheral (the peripheral is disabled) 6.5.10 I/O Short Address Location Register (SIM_ISALH and SIM_ISALL) The I/O Short Address Location registers are used to specify the memory referenced via the I/O short address mode. The I/O short address mode allows the instruction to specify the lower six bits of address; the upper address bits are not directly controllable. This register set allows limited control of the full address, as shown in Figure 6-13. Note: If this register is set to something other than the top of memory (EOnCE register space) and the EX bit in the OMR is set to 1, the JTAG port cannot access the on-chip EOnCE registers, and debug functions will be affected. “Hard Coded” Address Portion 6 Bits from I/O Short Address Mode Instruction Instruction Portion 16 Bits from SIM_ISALL Register 2 Bits from SIM_ISALH Register Full 24-Bit for Short I/O Address Figure 6-13 I/O Short Address Determination With this register set, an interrupt driver can set the SIM_ISALL register pair to point to its peripheral 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 113 registers and then use the I/O Short addressing mode to reference them. The ISR should restore this register to its previous contents prior to returning from interrupt. Note: Note: The default value of this register set points to the EOnCE registers. The pipeline delay between setting this register set and using short I/O addressing with the new value is three cycles. Base + $D Read Write RESET 15 1 14 1 13 1 12 1 11 1 10 1 9 1 8 1 7 1 6 1 5 1 4 1 3 1 2 1 1 0 ISAL[23:22] 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Figure 6-14 I/O Short Address Location High Register (SIM_ISALH) 6.5.10.1 Input/Output Short Address Low (ISAL[23:22])—Bit 1–0 This field represents the upper two address bits of the “hard coded” I/O short address. Base + $E Read Write RESET 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 ISAL[21:6] 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Figure 6-15 I/O Short Address Location Low Register (SIM_ISAL) 6.5.10.2 Input/Output Short Address Low (ISAL[21:6])—Bit 15–0 This field represents the lower 16 address bits of the “hard coded” I/O short address. 6.6 Clock Generation Overview The SIM uses an internal master clock from the OCCS (CLKGEN) module to produce the peripheral and system (core and memory) clocks. The maximum master clock frequency is 120MHz. Peripheral and system clocks are generated at half the master clock frequency and therefore at a maximum 60MHz. The SIM provides power modes (Stop, Wait) and clock enables (SIM_PCE register, CLK_DIS, ONCE_EBL) to control which clocks are in operation. The OCCS, power modes, and clock enables provide a flexible means to manage power consumption. Power utilization can be minimized in several ways. In the OCCS, crystal oscillator, and PLL may be shut down when not in use. When the PLL is in use, its prescaler and postscaler can be used to limit PLL and master clock frequency. Power modes permit system and/or peripheral clocks to be disabled when unused. Clock enables provide the means to disable individual clocks. Some peripherals provide further controls to disable unused subfunctions. Refer to Part 3 On-Chip Clock Synthesis (OCCS), and the 56F8300 Peripheral User Manual for further details. 56F8335 Technical Data, Rev. 5 114 Freescale Semiconductor Preliminary Power-Down Modes Overview 6.7 Power-Down Modes Overview The 56F8335/56F8135 operate in one of three power-down modes, as shown in Table 6-3. Table 6-3 Clock Operation in Power-Down Modes Mode Run Wait Core Clocks Active Core and memory clocks disabled Peripheral Clocks Active Active Description Device is fully functional Peripherals are active and can produce interrupts if they have not been masked off. Interrupts will cause the core to come out of its suspended state and resume normal operation. Typically used for power-conscious applications. The only possible recoveries from Stop mode are: 1. CAN traffic (1st message will be lost) 2. Non-clocked interrupts 3. COP reset 4. External reset 5. Power-on reset Stop System clocks continue to be generated in the SIM, but most are gated prior to reaching memory, core and peripherals. All peripherals, except the COP/watchdog timer, run off the IPBus clock frequency, which is the same as the main processor frequency in this architecture. The maximum frequency of operation is SYS_CLK = 60MHz. 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 115 6.8 Stop and Wait Mode Disable Function Permanent Disable D Q D-FLOP C 56800E Reprogrammable Disable D Q STOP_DIS D-FLOP Clock Select Reset C R Note: Wait disable circuit is similar Figure 6-16 Internal Stop Disable Circuit The 56800E core contains both STOP and WAIT instructions. Both put the CPU to sleep. For lowest power consumption in Stop mode, the PLL can be shut down. This must be done explicitly before entering Stop mode, since there is no automatic mechanism for this. When the PLL is shut down, the 56800E system clock must be set equal to the oscillator output. Some applications require the 56800E STOP and WAIT instructions to be disabled. To disable those instructions, write to the SIM control register (SIM_CONTROL), described in Part 6.5.1. This procedure can be on either a permanent or temporary basis. Permanently assigned applications last only until their next reset. 6.9 Resets The SIM supports four sources of reset. The two asynchronous sources are the external RESET pin and the Power-On Reset (POR). The two synchronous sources are the software reset, which is generated within the SIM itself by writing to the SIM_CONTROL register, and the COP reset. Reset begins with the assertion of any of the reset sources. Release of reset to various blocks is sequenced to permit proper operation of the device. A POR reset is first extended for 221 clock cycles to permit stabilization of the clock source, followed by a 32 clock window in which SIM clocking is initiated. It is then followed by a 32 clock window in which peripherals are released to implement Flash security, and, finally, followed by a 32 clock window in which the core is initialized. After completion of the described reset sequence, application code will begin execution. Resets may be asserted asynchronously, but are always released internally on a rising edge of the system clock. 56F8335 Technical Data, Rev. 5 116 Freescale Semiconductor Preliminary Operation with Security Enabled Part 7 Security Features The 56F8335/56F8135 offer security features intended to prevent unauthorized users from reading the contents of the Flash Memory (FM) array. The Flash security consists of several hardware interlocks that block the means by which an unauthorized user could gain access to the Flash array. However, part of the security must lie with the user’s code. An extreme example would be user’s code that dumps the contents of the internal program, as this code would defeat the purpose of security. At the same time, the user may also wish to put a “backdoor” in his program. As an example, the user downloads a security key through the SCI, allowing access to a programming routine that updates parameters stored in another section of the Flash. 7.1 Operation with Security Enabled Once the user has programmed the Flash with his application code, the device can be secured by programming the security bytes located in the FM configuration field, which occupies a portion of the FM array. These non-volatile bytes will keep the part secured through reset and through power-down of the device. Only two bytes within this field are used to enable or disable security. Refer to the Flash Memory section in the 56F8300 Peripheral User Manual for the state of the security bytes and the resulting state of security. When Flash security mode is enabled in accordance with the method described in the Flash Memory module specification, the device will disable the core EOnCE debug capabilities. Normal program execution is otherwise unaffected. 7.2 Flash Access Blocking Mechanisms The 56F8335/56F8135 have several operating functional and test modes. Effective Flash security must address operating mode selection and anticipate modes in which the on-chip Flash can be compromised and read without explicit user permission. Methods to block these are outlined in the next subsections. 7.2.1 • • Forced Operating Mode Selection Unsecured Mode Secure Mode (EOnCE disabled) At boot time, the SIM determines in which functional modes the device will operate. These are: When Flash security is enabled as described in the Flash Memory module specification, the device will disable the EOnCE debug interface. 7.2.2 Disabling EOnCE Access On-chip Flash can be read by issuing commands across the EOnCE port, which is the debug interface for the 56800E core. The TRST, TCLK, TMS, TDO, and TDI pins comprise a JTAG interface onto which the EOnCE port functionality is mapped. When the device boots, the chip-level JTAG TAP (Test Access Port) is active and provides the chip’s boundary scan capability and access to the ID register. Proper implementation of Flash security requires that no access to the EOnCE port is provided when security is enabled. The 56800E core has an input which disables reading of internal memory via the JTAG/EOnCE. The FM sets this input at reset to a value determined by the contents of the FM security bytes. 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 117 7.2.3 Flash Lockout Recovery If a user inadvertently enables Flash security on the device, a built-in lockout recovery mechanism can be used to reenable access to the device. This mechanism completely reases all on-chip Flash, thus disabling Flash security. Access to this recovery mechanism is built into CodeWarrior via an instruction in memory configuration (.cfg) files. Add, or uncomment the following configuration command: unlock_flash_on_connect 1 For more information, please see CodeWarrior MC56F83xx/DSP5685x Family Targeting Manual. The LOCKOUT_RECOVERY instruction has an associated 7-bit Data Register (DR) that is used to control the clock divider circuit within the FM module. This divider, FM_CLKDIV[6:0], is used to control the period of the clock used for timed events in the FM erase algorithm. This register must be set with appropriate values before the lockout sequence can begin. Refer to the JTAG section of the 56F8300 Peripheral User Manual for more details on setting this register value. The value of the JTAG FM_CLKDIV[6:0] will replace the value of the FM register FMCLKD that divides down the system clock for timed events, as illustrated in Figure 7-1. FM_CLKDIV[6] will map to the PRDIV8 bit, and FM_CLKDIV[5:0] will map to the DIV[5:0] bits. The combination of PRDIV8 and DIV must divide the FM input clock down to a frequency of 150kHz-200kHz. The “Writing the FMCLKD Register” section in the Flash Memory chapter of the 56F8300 Peripheral User Manual gives specific equations for calculating the correct values. Flash Memory SYS_CLK 2 input clock 7 FMCLKD 7 FM_CLKDIV JTAG FM_ERASE 7 DIVIDER Figure 7-1 JTAG to FM Connection for Lockout Recovery 56F8335 Technical Data, Rev. 5 118 Freescale Semiconductor Preliminary Flash Access Blocking Mechanisms Two examples of FM_CLKDIV calculations follow. EXAMPLE 1: If the system clock is the 8MHz crystal frequency because the PLL has not been set up, the input clock will be below 12.8MHz, so PRDIV8 = FM_CLKDIV[6] = 0. Using the following equation yields a DIV value of 19 for a clock of 200kHz, and a DIV value of 20 for a clock of 190kHz. This translates into an FM_CLKDIV[6:0] value of $13 or $14, respectively. 150[kHz] ( < SYS_CLK (2) (DIV + 1) )< 200[kHz] EXAMPLE 2: In this example, the system clock has been set up with a value of 32MHz, making the FM input clock 16MHz. Because that is greater than 12.8MHz, PRDIV8 = FM_CLKDIV[6] = 1. Using the following equation yields a DIV value of 9 for a clock of 200kHz, and a DIV value of 10 for a clock of 181kHz. This translates to an FM_CLKDIV[6:0] value of $49 or $4A, respectively. 150[kHz] < ( SYS_CLK (2) (DIV + 1) ) < 200[kHz] Once the LOCKOUT_RECOVERY instruction has been shifted into the instruction register, the clock divider value must be shifted into the corresponding 7-bit data register. After the data register has been updated, the user must transition the TAP controller into the RUN-TEST/IDLE state for the lockout sequence to commence. The controller must remain in this state until the erase sequence has completed. For details, see the JTAG Section in the 56F8300 Peripheral User Manual. Note: When the lockout recovery sequence has completed, the user must reset both the JTAG TAP controller (by asserting TRST) and the device (by asserting external chip reset) to return to normal unsecured operation. 7.2.4 Product Analysis The recommended method of unsecuring a programmed device for product analysis of field failures is via the backdoor key access. The customer would need to supply Technical Support with the backdoor key and the protocol to access the backdoor routine in the Flash. Additionally, the KEYEN bit that allows backdoor key access must be set. An alternative method for performing analysis on a secured hybrid controller would be to mass-erase and reprogram the Flash with the original code, but to modify the security bytes. To insure that a customer does not inadvertently lock himself out of the device during programming, it is recommended that he program the backdoor access key first, his application code second, and the security bytes within the FM configuration field last. 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 119 Part 8 General Purpose Input/Output (GPIO) 8.1 Introduction This section is intended to supplement the GPIO information found in the 56F8300 Peripheral User Manual and contains only chip-specific information. This information supercedes the generic information in the 56F8300 Peripheral User Manual. 8.2 Memory Maps The width of the GPIO port defines how many bits are implemented in each of the GPIO registers. Based on this and the default function of each of the GPIO pins, the reset values of the GPIOx_PUR and GPIOx_PER registers change from port to port. Tables 4-29 through 4-34 define the actual reset values of these registers. 8.3 Configuration There are six GPIO ports defined on the 56F8335/56F8135. The width of each port and the associated peripheral function is shown in Table 8-1 and Table 8-2. The specific mapping of GPIO port pins is shown in Table 8-3. Table 8-1 56F8335 GPIO Ports Configuration GPIO Port Port Width 14 8 11 Available Pins in 56F8335 Peripheral Function 6 pins - EMI Address pins - Can only be used as GPIO 8 pins - EMI Address pins - Not available in this package 5 pins - EMI Address pins - Can only be used as GPIO 3 pins - EMI Address pins - Not available in this package 4 pins - DEC1 / TMRB / SPI1 4 pins - DEC0 / TMRA 3 pins - PWMA current sense Reset Function EMI Address N/A GPIO N/A DEC1 / TMRB DEC0 / TMRA PWMA current sense A B C 6 5 11 56F8335 Technical Data, Rev. 5 120 Freescale Semiconductor Preliminary Configuration Table 8-1 56F8335 GPIO Ports Configuration GPIO Port Port Width 13 Available Pins in 56F8335 Peripheral Function 2 pins - EMI CSn 4 pins - EMI CSn - Can only be used as GPIO 2 pins - SCI1 2 pins - EMI CSn - Not available in this package 3 pins - PWMB current sense 2 pins - SCI0 2 pins - EMI Address pins - Not available in this package 4 pins - SPI0 2 pins - TMRC 4 pins - TMRD 4 pins - EMI Data - Can only be used as GPIO 12 pins - EMI Data - Not available in this package Reset Function EMI Chip Selects EMI Chip Selects SCI1 N/A PWMB current sense SCI0 N/A SPI0 TMRC TMRD EMI Data N/A D 11 E 14 12 F 16 4 Table 8-2 56F8135 GPIO Ports Configuration GPIO Port Port Width 14 8 11 Available Pins in 56F8135 6 5 11 Peripheral Function 6 pins - EMI Address pins - Can only be used as GPIO 8 pins - EMI Address pins - Not available in this package 5 pins - EMI Address pins - Can only be used as GPIO 3 pins - EMI Address pins - Not available in this package 4 pins - SPI1 4 pins - DEC0 / TMRA 3 pins - Dedicated GPIO 6 pins - EMI CSn - Can only be used as GPIO 2 pins - SCI1 2 pins - EMI CSn - Not available in this package 3 pins - PWMB current sense 2 pins - SCI0 2 pins - EMI Address pins - Not available in this package 4 pins - SPI0 2 pins - TMRC 4 pins - Dedicated GPIO 4 pins - EMI Data - Can only be used as GPIO 12 pins - EMI Data - Not available in this package Reset Function EMI Address N/A GPIO N/A DEC1 / TMRB DEC0 / TMRA GPIO EMI Chip Selects SCI1 N/A PWMB current sense SCI0 N/A SPI0 TMRC GPIO EMI Data N/A A B C D 13 11 E 14 12 F 16 4 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 121 Table 8-3 GPIO External Signals Map Pins in shaded rows are not available in 56F8335 / 56F8135 Pins in italics are NOT available in the 56F8135 device GPIO Port GPIO Bit 0 1 2 3 4 5 GPIOA 6 7 8 9 10 11 12 13 0 1 2 GPIOB 3 4 5 6 7 Reset Function Peripheral Peripheral Peripheral Peripheral Peripheral Peripheral N/A N/A N/A N/A N/A N/A N/A N/A GPIO GPIO GPIO GPIO GPIO N/A N/A N/A A161 A171 A181 A191 A20 / Prescaler_clock 27 28 29 30 31 Functional Signal A81 A91 A101 A111 A121 A131 Package Pin # 15 16 17 18 19 20 56F8335 Technical Data, Rev. 5 122 Freescale Semiconductor Preliminary Configuration Table 8-3 GPIO External Signals Map (Continued) Pins in shaded rows are not available in 56F8335 / 56F8135 Pins in italics are NOT available in the 56F8135 device GPIO Port GPIO Bit 0 1 Reset Function Peripheral Peripheral Functional Signal PHASEA1 / TB0 / SCLK12 PHASEB1 / TB1 / PHASEB1 / TB1 / MOSI12 INDEX1 / TB2 / MISO12 HOME1 / TB3 /SS12 PHASEA0 / TA0 PHASEB0 / TA1 INDEX0 / TA2 HOME0 / TA3 ISA0 ISA1 ISA2 CS21 CS31 CS41 CS51 CS61 CS71 TXD1 RXD1 Package Pin # 9 10 2 3 GPIOC 4 5 6 7 8 9 10 0 1 2 3 4 5 GPIOD 6 7 8 9 10 11 12 Peripheral Peripheral Peripheral Peripheral Peripheral Peripheral Peripheral Peripheral Peripheral GPIO GPIO GPIO GPIO GPIO GPIO Peripheral Peripheral N/A N/A Peripheral Peripheral Peripheral 11 12 127 128 1 2 104 105 106 42 43 44 45 46 47 40 41 ISB0 ISB1 ISB2 48 50 51 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 123 Table 8-3 GPIO External Signals Map (Continued) Pins in shaded rows are not available in 56F8335 / 56F8135 Pins in italics are NOT available in the 56F8135 device GPIO Port GPIO Bit 0 1 2 3 4 5 GPIOE 6 7 8 9 10 11 12 13 Reset Function Peripheral Peripheral N/A N/A Peripheral Peripheral Peripheral Peripheral Peripheral Peripheral Peripheral Peripheral Peripheral Peripheral SCLK0 MOSI0 MISO0 SS0 TC0 TC1 TD0 TD1 TD2 TD3 124 126 125 123 111 113 107 108 109 110 Functional Signal TXD0 RXD0 Package Pin # 7 8 56F8335 Technical Data, Rev. 5 124 Freescale Semiconductor Preliminary JTAG Information Table 8-3 GPIO External Signals Map (Continued) Pins in shaded rows are not available in 56F8335 / 56F8135 Pins in italics are NOT available in the 56F8135 device GPIO Port GPIO Bit 0 1 2 3 4 5 6 GPIOF 7 8 9 10 11 12 13 14 15 Reset Function Peripheral Peripheral Peripheral Peripheral N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A Functional Signal D71 D81 D91 D101 Package Pin # 22 23 24 26 1. Not useful in reset configuration in this package - reconfigure as GPIO 2. See Part 6.5.8 to determine how to select peripherals from this set; DEC1 is the selected peripheral at reset Part 9 Joint Test Action Group (JTAG) 9.1 JTAG Information Please contact your Freescale marketing device/package-specific BSDL information. representative or authorized distributor for 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 125 Part 10 Specifications 10.1 General Characteristics The 56F8335/56F8135 are fabricated in high-density CMOS with 5V-tolerant TTL-compatible digital inputs. The term “5V-tolerant” refers to the capability of an I/O pin, built on a 3.3V-compatible process technology, to withstand a voltage up to 5.5V without damaging the device. Many systems have a mixture of devices designed for 3.3V and 5V power supplies. In such systems, a bus may carry both 3.3V- and 5V-compatible I/O voltage levels (a standard 3.3V I/O is designed to receive a maximum voltage of 3.3V ± 10% during normal operation without causing damage). This 5V-tolerant capability therefore offers the power savings of 3.3V I/O levels combined with the ability to receive 5V levels without damage. Absolute maximum ratings in Table 10-1 are stress ratings only, and functional operation at the maximum is not guaranteed. Stress beyond these ratings may affect device reliability or cause permanent damage to the device. Note: All specifications meet both Automotive and Industrial requirements unless individual specifications are listed. Note: The 56F8135 device is guaranteed to 40MHz and specified to meet Industrial requirements only. CAUTION This device contains protective circuitry to guard against damage due to high static voltage or electrical fields. However, normal precautions are advised to avoid application of any voltages higher than maximum-rated voltages to this high-impedance circuit. Reliability of operation is enhanced if unused inputs are tied to an appropriate voltage level. Note: The 56F8135 device is specified to meet Industrial requirements only; CAN is NOT available on the 56F8135 device. Table 10-1 Absolute Maximum Ratings (VSS = VSSA_ADC = 0) Characteristic Supply voltage ADC Supply Voltage Oscillator / PLL Supply Voltage Internal Logic Core Supply Voltage Input Voltage (digital) Symbol VDD_IO VDDA_ADC, VREFH VDDA_OSC_PLL VDD_CORE VIN OCR_DIS is High Pin Groups 1, 2, 5, 6, 9, 10 Notes Min - 0.3 Max 4.0 4.0 4.0 3.0 6.0 Unit V V V V V VREFH must be less than or equal to VDDA_ADC - 0.3 - 0.3 - 0.3 -0.3 56F8335 Technical Data, Rev. 5 126 Freescale Semiconductor Preliminary General Characteristics Table 10-1 Absolute Maximum Ratings (Continued) (VSS = VSSA_ADC = 0) Characteristic Input Voltage (analog) Output Voltage Output Voltage (open drain) Ambient Temperature (Automotive) Ambient Temperature (Industrial) Junction Temperature (Automotive) Junction Temperature (Industrial) Storage Temperature (Automotive) Storage Temperature (Industrial) Symbol VINA VOUT VOD TA TA TJ TJ TSTG TSTG Notes Pin Groups 11, 12, 13 Pin Groups 1, 2, 3, 4, 5, 6, 7, 8 Min -0.3 -0.3 -0.3 -40 -40 -40 -40 -55 -55 Max 4.0 4.0 6.01 6.0 125 105 150 125 150 150 Unit V V V °C °C °C °C °C °C Pin Group 4 1. If corresponding GPIO pin is configured as open drain. Note: Pins in italics are NOT available in the 56F8135 device. Pin Group 1: TXD0-1, RXD0-1, SS0, MISO0, MOSI0 Pin Group 2: PHASEA0, PHASEA1, PHASEB0, PHASEB1, INDEX0, INDEX1, HOME0, HOME1, ISB0-2, ISA0-2, TD2-3, TC0-1, TDO, SCLK0 Pin Group 3: RSTO, TDO Pin Group 4: CAN_TX Pin Group 5: D0-15, GPIOD0-5 Pin Group 6: A8-15, GPIOB0-4, TD0-1 Pin Group 7: CLKO Pin Group 8: PWMA0-5, PWMB0-5 Pin Group 9: IRQA, IRQB, RESET, EXTBOOT, TRST,TMS, TDI, CAN_RX, EMI_MODE, FAULTA0-3, FAULTB0-3 Pin Group 10: TCK Pin Group 11: XTAL, EXTAL Pin Group 12: ANA0-7, ANB0-7 Pin Group 13: OCR_DIS, CLKMODE 56F8335 Technical Data, Rev. 5 Freescale Semiconductor Preliminary 127 Table 10-2 ElectroStatic Discharge (ESD) Protection Characteristic ESD for Human Body Model (HBM) ESD for Machine Model (MM) ESD for Charge Device Model (CDM) Min 2000 200 500 Typ — — — Max — — — Unit V V V Table 10-3 Thermal Characteristics6 Value Characteristic Comments Symbol 128-pin LQFP Unit Notes Junction to ambient Natural convection Junction to ambient (@1m/sec) Junction to ambient Natural convection Junction to ambient (@1m/sec) Junction to case Junction to center of case I/O pin power dissipation Power dissipation Maximum allowed PD Four layer board (2s2p) RθJA RθJMA RθJMA (2s2p) RθJMA RθJC ΨJT P I/O PD PDMAX 50.8 46.5 43.9 °C/W °C/W °C/W 2 2 1,2 Four layer board (2s2p) 41.7 13.9 1.2 User-determined P D = (IDD x VDD + P I/O) (TJ - TA) / RθJA7 °C/W °C/W °C/W W W W 1,2 3 4, 5 1. Theta-JA determined on 2s2p test boards is frequently lower than would be observed in an application. Determined on 2s2p thermal test board. 2. Junction to ambient thermal resistance, Theta-JA (RθJA) was simulated to be equivalent to the JEDEC specification JESD51-2 in a horizontal configuration in natural convection. Theta-JA was also simulated on a thermal test board with two internal planes (2s2p, where “s” is the number of signal layers and “p” is the number of planes) per JESD51-6 and JESD51-7. The correct name for Theta-JA for forced convection or with the non-single layer boards is Theta-JMA. 3. Junction to case thermal resistance, Theta-JC (RθJC ), was simulated to be equivalent to the measured values using the cold plate technique with the cold plate temperature used as the "case" temperature. The basic cold plate measurement technique is described by MIL-STD 883D, Method 1012.1. This is the correct thermal metric to use to calculate thermal performance when the package is being used with a heat sink. 4. Thermal Characterization Parameter, Psi-JT (ΨJT ), is the "resistance" from junction to reference point thermocouple on top center of case as defined in JESD51-2. ΨJT is a useful value to use to estimate junction temperature in steady-state customer environments. 5. Junction temperature is a function of on-chip power dissipation, package thermal resistance, mounting site (board) temperature, ambient temperature, air flow, power dissipation of other components on the board, and board thermal resistance. 6. See Part 12.1 for more details on thermal design considerations. 56F8335 Technical Data, Rev. 5 128 Freescale Semiconductor Preliminary General Characteristics 7. TJ = Junction Temperature TA = Ambient Temperature Note: The 56F8135 device is guaranteed to 40MHz and specified to meet Industrial requirements only; CAN is NOT available on the 56F8135 device. Table 10-4 Operating Conditions (VREFLO = 0V, VSS = VSSA_ADC = 0V, VDDA = VDDA_ADC = VDDA_OSC_PLL ) Characteristic Supply voltage ADC Supply Voltage Symbol VDD_IO VDDA_ADC, VREFH VDDA_OSC _PLL Notes Min 3 Typ 3.3 3.3 Max 3.6 3.6 Unit V V VREFH must be less than or equal to VDDA_ADC 3 Oscillator / PLL Supply Voltage Internal Logic Core Supply Voltage Device Clock Frequency Input High Voltage (digital) Input High Voltage (analog) Input High Voltage (XTAL/EXTAL, XTAL is not driven by an external clock) 3 OCR_DIS is High 3.3 2.5 — — — — — — — — — — — — — — — — — 3.6 2.75 60 5.5 VDDA+0.3 VDDA+0.3 VDDA+0.3 .8 -4 -8 -12 4 8 12 125 105 V V MHz V V V V V mA VDD_CORE FSYSCLK VIN VIHA VIHC VIHC VIL IOH 2.25 0 Pin Groups 1, 2, 5, 6, 9, 10 Pin Group 13 Pin Group 11 Pin Group 11 Pin Groups 1, 2, 5, 6, 9, 10, 11, 13 Pin Groups 1, 2, 3 Pin Groups 5, 6, 7 Pin Groups 8 2 2 VDDA-0.8 2 -0.3 — — — — — — -40 -40 Input high voltage (XTAL/EXTAL, XTAL is driven by an external clock) Input Low Voltage Output High Source Current VOH = 2.4V (VOH min.) Output Low Sink Current VOL = 0.4V (VOL max) IOL Pin Groups 1, 2, 3, 4 Pin Groups 5, 6, 7 Pin Group 8 mA Ambient Operating Temperature (Automotive) Ambient Operating Temperature (Industrial) Flash Endurance (Automotive) (Program Erase Cycles) Flash Endurance (Industrial) (Program Erase Cycles) Flash Data Retention (Automotive) TA TA NF NF TR TA = -40°C to 125°C TA = -40°C to 105°C TJ