MC9S08JM32CGTE

MC9S08JM60 MC9S08JM32 Data Sheet HCS08 Microcontrollers MC9S08JM60 Rev. 3 1/2009 freescale.com MC9S08JM60 Series Features 8-Bit HCS08 Central Processor Unit (CPU) • • • • • 48-MHz HCS08 CPU (central processor unit) 24-MHz internal bus frequency HC08 instruction set with added BGND instruction Background debugging system Breakpoint capability to allow single breakpoint setting during in-circuit debugging (plus two more breakpoints in on-chip debug module) • In-circuit emulator (ICE) debug module containing two comparators and nine trigger modes. Eight deep FIFO for storing change-of-flow addresses and event-only data. Debug module supports both tag and force breakpoints. • Support for up to 32 interrupt/reset sources • SPI — Two 8- or 16-bit selectable serial peripheral interface modules with a receive data buffer hardware match function • IIC — Inter-integrated circuit bus module to operate at up to 100 kbps with maximum bus loading; multi-master operation; programmable slave address; interrupt-driven byte-by-byte data transfer; 10-bit addressing and broadcast modes support • Timers — One 2-channel and one 6-channel 16-bit timer/pulse-width modulator (TPM) modules: Selectable input capture, output compare, and edge-aligned PWM capability on each channel. Each timer module may be configured for buffered, centered PWM (CPWM) on all channels • KBI — 8-pin keyboard interrupt module • RTC — Real-time counter with binary- or decimal-based prescaler Memory Options • Up to 60 KB of on-chip in-circuit programmable flash memory with block protection and security options • Up to 4 KB of on-chip RAM • 256 bytes of USB RAM Input/Output • Up to 51 general-purpose input/output pins • Software selectable pullups on ports when used as inputs • Software selectable slew rate control on ports when used as outputs • Software selectable drive strength on ports when used as outputs • Master reset pin and power-on reset (POR) • Internal pullup on RESET, IRQ, and BKGD/MS pins to reduce customer system cost Clock Source Options • Clock source options include crystal, resonator, external clock • MCG (multi-purpose clock generator) — PLL and FLL; internal reference clock with trim adjustment System Protection • Optional computer operating properly (COP) reset with option to run from independent 1-kHz internal clock source or the bus clock • Low-voltage detection with reset or interrupt • Illegal opcode detection with reset • Illegal address detection with reset Package Options • • • • 64-pin quad flat package (QFP) 64-pin low-profile quad flat package (LQFP) 48-pin quad flat no-lead (QFN) 44-pin low-profile quad flat package (LQFP) Power-Saving Modes • Wait plus two stops Peripherals • USB — USB 2.0 full-speed (12 Mbps) device controller with dedicated on-chip USB transceiver, 3.3-V regulator and USBDP pull-up resister; supports control, interrupt, isochronous, and bulk transfers; supports endpoint 0 and up to 6 additional endpoints; endpoints 5 and 6 can be combined to provide double buffering capability • ADC — 12-channel, 12-bit analog-to-digital converter with automatic compare function; internal temperature sensor • ACMP — Analog comparator with option to compare to internal reference; operation in stop3 mode • SCI — Two serial communications interface modules with optional 13-bit break LIN extensions MC9S08JM60 Series Data Sheet Covers MC9S08JM60 MC9S08JM32 MC9S08JM60 Rev. 3 1/2009 Revision History To provide the most up-to-date information, the revision of our documents on the World Wide Web will be the most current. Your printed copy may be an earlier revision. To verify you have the latest information available, refer to: http://freescale.com/ The following revision history table summarizes changes contained in this document. Revision Number 1 Revision Date 11/27/2007 Initial release Description of Changes 2 3/4/2008 Changed the location of RS to connect to EXTAL in Figure 2-4. Changed port rise and fall time in Table A-13. Added DC injection current and RAM retention voltage in Table A-6. Deleted note on 625 ns of item 17 in Table A-12. Moved Bandgap Voltage Reference item from Table A-8 to Table A-6. Added one paragraph on how to improve accuracy to Section 10.1.1.5, “Temperature Sensor.” Changed the VTEMP25 from 1.396 mV to 1.396 V in Table A-10. Complete the EMC data in Section A.15, “EMC Performance.” Revised the Typo in Table 11-4. 3 1/21/2009 This product incorporates SuperFlash® technology licensed from SST. Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc. © Freescale Semiconductor, Inc., 2007-2009. All rights reserved. List of Chapters Chapter Number Title Page Chapter 1 Device Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Chapter 2 Pins and Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Chapter 3 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Chapter 4 Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Chapter 5 Resets, Interrupts, and System Configuration . . . . . . . . . . . . . . . 65 Chapter 6 Parallel Input/Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 Chapter 7 Central Processor Unit (S08CPUV2) . . . . . . . . . . . . . . . . . . . . . . . 99 Chapter 8 5 V Analog Comparator (S08ACMPV2) . . . . . . . . . . . . . . . . . . . . 119 Chapter 9 Keyboard Interrupt (S08KBIV2) . . . . . . . . . . . . . . . . . . . . . . . . . . 127 Chapter 10 Analog-to-Digital Converter (S08ADC12V1) . . . . . . . . . . . . . . . 135 Chapter 11 Inter-Integrated Circuit (S08IICV2) . . . . . . . . . . . . . . . . . . . . . . . 161 Chapter 12 Multi-Purpose Clock Generator (S08MCGV1) . . . . . . . . . . . . . . 181 Chapter 13 Real-Time Counter (S08RTCV1) . . . . . . . . . . . . . . . . . . . . . . . . . 213 Chapter 14 Serial Communications Interface (S08SCIV4) . . . . . . . . . . . . . . 223 Chapter 15 16-Bit Serial Peripheral Interface (S08SPI16V1) . . . . . . . . . . . . 243 Chapter 16 Timer/Pulse-Width Modulator (S08TPMV3) . . . . . . . . . . . . . . . . 271 Chapter 17 Universal Serial Bus Device Controller (S08USBV1) . . . . . . . . 295 Chapter 18 Development Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 327 Appendix A Electrical Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 349 Appendix B Ordering Information and Mechanical Drawings. . . . . . . . . . 373 MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 7 Contents Section Number Title Chapter 1 Device Overview 1.1 1.2 1.3 Introduction .....................................................................................................................................19 MCU Block Diagram ......................................................................................................................19 System Clock Distribution ..............................................................................................................21 Page Chapter 2 Pins and Connections 2.1 2.2 2.3 Introduction .....................................................................................................................................25 Device Pin Assignment ...................................................................................................................26 Recommended System Connections ...............................................................................................28 2.3.1 Power (VDD, VSS, VSSOSC, VDDAD, VSSAD, VUSB33) ....................................................30 2.3.2 Oscillator (XTAL, EXTAL) ..............................................................................................30 2.3.3 RESET Pin ........................................................................................................................31 2.3.4 Background/Mode Select (BKGD/MS) ............................................................................31 2.3.5 ADC Reference Pins (VREFH, VREFL) .............................................................................31 2.3.6 External Interrupt Pin (IRQ) .............................................................................................31 2.3.7 USB Data Pins (USBDP, USBDN) ...................................................................................32 2.3.8 General-Purpose I/O and Peripheral Ports ........................................................................32 Chapter 3 Modes of Operation 3.1 3.2 3.3 3.4 3.5 3.6 Introduction .....................................................................................................................................35 Features ...........................................................................................................................................35 Run Mode ........................................................................................................................................35 Active Background Mode ...............................................................................................................35 Wait Mode .......................................................................................................................................36 Stop Modes ......................................................................................................................................37 3.6.1 Stop3 Mode .......................................................................................................................37 3.6.2 Stop2 Mode .......................................................................................................................38 3.6.3 On-Chip Peripheral Modules in Stop Modes ....................................................................39 Chapter 4 Memory 4.1 4.2 4.3 4.4 MC9S08JM60 Series Memory Map ...............................................................................................41 4.1.1 Reset and Interrupt Vector Assignments ...........................................................................42 Register Addresses and Bit Assignments ........................................................................................43 RAM (System RAM) ......................................................................................................................50 USB RAM .......................................................................................................................................51 MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 9 4.5 4.6 4.7 Flash ................................................................................................................................................51 4.5.1 Features .............................................................................................................................51 4.5.2 Program and Erase Times .................................................................................................52 4.5.3 Program and Erase Command Execution .........................................................................52 4.5.4 Burst Program Execution ..................................................................................................54 4.5.5 Access Errors ....................................................................................................................55 4.5.6 Flash Block Protection ......................................................................................................56 4.5.7 Vector Redirection ............................................................................................................57 Security ............................................................................................................................................57 Flash Registers and Control Bits .....................................................................................................58 4.7.1 Flash Clock Divider Register (FCDIV) ............................................................................59 4.7.2 Flash Options Register (FOPT and NVOPT) ....................................................................60 4.7.3 Flash Configuration Register (FCNFG) ...........................................................................61 4.7.4 Flash Protection Register (FPROT and NVPROT) ..........................................................61 4.7.5 Flash Status Register (FSTAT) ..........................................................................................62 4.7.6 Flash Command Register (FCMD) ...................................................................................63 Chapter 5 Resets, Interrupts, and System Configuration 5.1 5.2 5.3 5.4 5.5 Introduction .....................................................................................................................................65 Features ...........................................................................................................................................65 MCU Reset ......................................................................................................................................65 Computer Operating Properly (COP) Watchdog .............................................................................66 Interrupts .........................................................................................................................................67 5.5.1 Interrupt Stack Frame .......................................................................................................68 5.5.2 External Interrupt Request (IRQ) Pin ...............................................................................68 5.5.3 Interrupt Vectors, Sources, and Local Masks ...................................................................69 Low-Voltage Detect (LVD) System ................................................................................................71 5.6.1 Power-On Reset Operation ...............................................................................................71 5.6.2 Low-Voltage Detection (LVD) Reset Operation ...............................................................71 5.6.3 Low-Voltage Warning (LVW) Interrupt Operation ...........................................................71 Reset, Interrupt, and System Control Registers and Control Bits ...................................................72 5.7.1 Interrupt Pin Request Status and Control Register (IRQSC) ............................................72 5.7.2 System Reset Status Register (SRS) .................................................................................73 5.7.3 System Background Debug Force Reset Register (SBDFR) ............................................74 5.7.4 System Options Register 1 (SOPT1) ................................................................................74 5.7.5 System Options Register 2 (SOPT2) ................................................................................76 5.7.6 System Device Identification Register (SDIDH, SDIDL) ................................................76 5.7.7 System Power Management Status and Control 1 Register (SPMSC1) ...........................77 5.7.8 System Power Management Status and Control 2 Register (SPMSC2) ...........................78 5.6 5.7 Chapter 6 Parallel Input/Output 6.1 6.2 Introduction .....................................................................................................................................81 Port Data and Data Direction ..........................................................................................................81 MC9S08JM60 Series Data Sheet, Rev. 3 10 Freescale Semiconductor 6.3 6.4 6.5 Pin Control ......................................................................................................................................82 6.3.1 Internal Pullup Enable ......................................................................................................83 6.3.2 Output Slew Rate Control Enable .....................................................................................83 6.3.3 Output Drive Strength Select ............................................................................................83 Pin Behavior in Stop Modes ............................................................................................................83 Parallel I/O and Pin Control Registers ............................................................................................83 6.5.1 Port A I/O Registers (PTAD and PTADD) ........................................................................84 6.5.2 Port A Pin Control Registers (PTAPE, PTASE, PTADS) .................................................84 6.5.3 Port B I/O Registers (PTBD and PTBDD) ........................................................................86 6.5.4 Port B Pin Control Registers (PTBPE, PTBSE, PTBDS) .................................................86 6.5.5 Port C I/O Registers (PTCD and PTCDD) ........................................................................88 6.5.6 Port C Pin Control Registers (PTCPE, PTCSE, PTCDS) .................................................88 6.5.7 Port D I/O Registers (PTDD and PTDDD) .......................................................................90 6.5.8 Port D Pin Control Registers (PTDPE, PTDSE, PTDDS) ................................................90 6.5.9 Port E I/O Registers (PTED and PTEDD) ........................................................................92 6.5.10 Port E Pin Control Registers (PTEPE, PTESE, PTEDS) ..................................................92 6.5.11 Port F I/O Registers (PTFD and PTFDD) .........................................................................94 6.5.12 Port F Pin Control Registers (PTFPE, PTFSE, PTFDS) ...................................................94 6.5.13 Port G I/O Registers (PTGD and PTGDD) .......................................................................96 6.5.14 Port G Pin Control Registers (PTGPE, PTGSE, PTGDS) ................................................96 Chapter 7 Central Processor Unit (S08CPUV2) 7.1 7.2 Introduction .....................................................................................................................................99 7.1.1 Features .............................................................................................................................99 Programmer’s Model and CPU Registers .....................................................................................100 7.2.1 Accumulator (A) .............................................................................................................100 7.2.2 Index Register (H:X) ......................................................................................................100 7.2.3 Stack Pointer (SP) ...........................................................................................................101 7.2.4 Program Counter (PC) ....................................................................................................101 7.2.5 Condition Code Register (CCR) .....................................................................................101 Addressing Modes .........................................................................................................................103 7.3.1 Inherent Addressing Mode (INH) ...................................................................................103 7.3.2 Relative Addressing Mode (REL) ..................................................................................103 7.3.3 Immediate Addressing Mode (IMM) ..............................................................................103 7.3.4 Direct Addressing Mode (DIR) ......................................................................................103 7.3.5 Extended Addressing Mode (EXT) ................................................................................104 7.3.6 Indexed Addressing Mode ..............................................................................................104 Special Operations .........................................................................................................................105 7.4.1 Reset Sequence ...............................................................................................................105 7.4.2 Interrupt Sequence ..........................................................................................................105 7.4.3 Wait Mode Operation ......................................................................................................106 7.4.4 Stop Mode Operation ......................................................................................................106 7.4.5 BGND Instruction ...........................................................................................................107 HCS08 Instruction Set Summary ..................................................................................................108 MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 11 7.3 7.4 7.5 Chapter 8 5 V Analog Comparator (S08ACMPV2) 8.1 Introduction ...................................................................................................................................119 8.1.1 ACMP Configuration Information ..................................................................................119 8.1.2 ACMP/TPM Configuration Information ........................................................................119 8.1.3 Features ...........................................................................................................................121 8.1.4 Modes of Operation ........................................................................................................121 8.1.5 Block Diagram ................................................................................................................121 External Signal Description ..........................................................................................................123 Memory Map ................................................................................................................................123 8.3.1 Register Descriptions ......................................................................................................123 Functional Description ..................................................................................................................125 8.2 8.3 8.4 Chapter 9 Keyboard Interrupt (S08KBIV2) 9.1 Introduction ...................................................................................................................................127 9.1.1 Features ...........................................................................................................................129 9.1.2 Modes of Operation ........................................................................................................129 9.1.3 Block Diagram ................................................................................................................129 External Signal Description ..........................................................................................................130 Register Definition ........................................................................................................................130 9.3.1 KBI Status and Control Register (KBISC) .....................................................................130 9.3.2 KBI Pin Enable Register (KBIPE) ..................................................................................131 9.3.3 KBI Edge Select Register (KBIES) ................................................................................131 Functional Description ..................................................................................................................132 9.4.1 Edge Only Sensitivity .....................................................................................................132 9.4.2 Edge and Level Sensitivity .............................................................................................132 9.4.3 KBI Pullup/Pulldown Resistors ......................................................................................133 9.4.4 KBI Initialization ............................................................................................................133 9.2 9.3 9.4 Chapter 10 Analog-to-Digital Converter (S08ADC12V1) 10.1 Overview .......................................................................................................................................135 10.1.1 Module Configurations ...................................................................................................135 10.1.2 Low-Power Mode Operation ..........................................................................................137 10.1.3 Features ...........................................................................................................................139 10.1.4 ADC Module Block Diagram .........................................................................................139 10.2 External Signal Description ..........................................................................................................140 10.2.1 Analog Power (VDDAD) ..................................................................................................141 10.2.2 Analog Ground (VSSAD) .................................................................................................141 10.2.3 Voltage Reference High (VREFH) ...................................................................................141 10.2.4 Voltage Reference Low (VREFL) ....................................................................................141 10.2.5 Analog Channel Inputs (ADx) ........................................................................................141 10.3 Register Definition ........................................................................................................................141 10.3.1 Status and Control Register 1 (ADCSC1) ......................................................................141 MC9S08JM60 Series Data Sheet, Rev. 3 12 Freescale Semiconductor 10.3.2 Status and Control Register 2 (ADCSC2) ......................................................................143 10.3.3 Data Result High Register (ADCRH) .............................................................................143 10.3.4 Data Result Low Register (ADCRL) ..............................................................................144 10.3.5 Compare Value High Register (ADCCVH) ....................................................................144 10.3.6 Compare Value Low Register (ADCCVL) .....................................................................145 10.3.7 Configuration Register (ADCCFG) ................................................................................145 10.3.8 Pin Control 1 Register (APCTL1) ..................................................................................146 10.3.9 Pin Control 2 Register (APCTL2) ..................................................................................147 10.3.10Pin Control 3 Register (APCTL3) ..................................................................................148 10.4 Functional Description ..................................................................................................................149 10.4.1 Clock Select and Divide Control ....................................................................................150 10.4.2 Input Select and Pin Control ...........................................................................................150 10.4.3 Hardware Trigger ............................................................................................................150 10.4.4 Conversion Control .........................................................................................................150 10.4.5 Automatic Compare Function .........................................................................................153 10.4.6 MCU Wait Mode Operation ............................................................................................153 10.4.7 MCU Stop3 Mode Operation ..........................................................................................154 10.4.8 MCU Stop2 Mode Operation ..........................................................................................154 10.5 Initialization Information ..............................................................................................................154 10.5.1 ADC Module Initialization Example .............................................................................155 10.6 Application Information ................................................................................................................156 10.6.1 External Pins and Routing ..............................................................................................156 10.6.2 Sources of Error ..............................................................................................................158 Chapter 11 Inter-Integrated Circuit (S08IICV2) 11.1 Introduction ...................................................................................................................................161 11.1.1 Features ...........................................................................................................................163 11.1.2 Modes of Operation ........................................................................................................163 11.1.3 Block Diagram ................................................................................................................163 11.2 External Signal Description ..........................................................................................................164 11.2.1 SCL — Serial Clock Line ...............................................................................................164 11.2.2 SDA — Serial Data Line ................................................................................................164 11.3 Register Definition ........................................................................................................................164 11.3.1 IIC Address Register (IICA) ...........................................................................................165 11.3.2 IIC Frequency Divider Register (IICF) ..........................................................................165 11.3.3 IIC Control Register (IICC1) ..........................................................................................168 11.3.4 IIC Status Register (IICS) ...............................................................................................168 11.3.5 IIC Data I/O Register (IICD) ..........................................................................................169 11.3.6 IIC Control Register 2 (IICC2) .......................................................................................170 11.4 Functional Description ..................................................................................................................171 11.4.1 IIC Protocol .....................................................................................................................171 11.4.2 10-bit Address .................................................................................................................174 11.4.3 General Call Address ......................................................................................................175 11.5 Resets ............................................................................................................................................175 MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 13 11.6 Interrupts .......................................................................................................................................175 11.6.1 Byte Transfer Interrupt ....................................................................................................175 11.6.2 Address Detect Interrupt .................................................................................................176 11.6.3 Arbitration Lost Interrupt ................................................................................................176 11.7 Initialization/Application Information ..........................................................................................177 Chapter 12 Multi-Purpose Clock Generator (S08MCGV1) 12.1 Introduction ...................................................................................................................................181 12.1.1 Features ...........................................................................................................................183 12.1.2 Modes of Operation ........................................................................................................185 12.2 External Signal Description ..........................................................................................................185 12.3 Register Definition ........................................................................................................................186 12.3.1 MCG Control Register 1 (MCGC1) ...............................................................................186 12.3.2 MCG Control Register 2 (MCGC2) ...............................................................................187 12.3.3 MCG Trim Register (MCGTRM) ...................................................................................188 12.3.4 MCG Status and Control Register (MCGSC) .................................................................189 12.3.5 MCG Control Register 3 (MCGC3) ...............................................................................190 12.4 Functional Description ..................................................................................................................192 12.4.1 Operational Modes ..........................................................................................................192 12.4.2 Mode Switching ..............................................................................................................196 12.4.3 Bus Frequency Divider ...................................................................................................196 12.4.4 Low Power Bit Usage .....................................................................................................197 12.4.5 Internal Reference Clock ................................................................................................197 12.4.6 External Reference Clock ...............................................................................................197 12.4.7 Fixed Frequency Clock ...................................................................................................197 12.5 Initialization / Application Information ........................................................................................198 12.5.1 MCG Module Initialization Sequence ............................................................................198 12.5.2 MCG Mode Switching ....................................................................................................199 12.5.3 Calibrating the Internal Reference Clock (IRC) .............................................................210 Chapter 13 Real-Time Counter (S08RTCV1) 13.1 Introduction ...................................................................................................................................213 13.1.1 Features ...........................................................................................................................215 13.1.2 Modes of Operation ........................................................................................................215 13.1.3 Block Diagram ................................................................................................................216 13.2 External Signal Description ..........................................................................................................216 13.3 Register Definition ........................................................................................................................216 13.3.1 RTC Status and Control Register (RTCSC) ....................................................................217 13.3.2 RTC Counter Register (RTCCNT) ..................................................................................218 13.3.3 RTC Modulo Register (RTCMOD) ................................................................................218 13.4 Functional Description ..................................................................................................................218 13.4.1 RTC Operation Example .................................................................................................219 13.5 Initialization/Application Information ..........................................................................................220 MC9S08JM60 Series Data Sheet, Rev. 3 14 Freescale Semiconductor Chapter 14 Serial Communications Interface (S08SCIV4) 14.1 Introduction ...................................................................................................................................223 14.1.1 Features ...........................................................................................................................225 14.1.2 Modes of Operation ........................................................................................................225 14.1.3 Block Diagram ................................................................................................................226 14.2 Register Definition ........................................................................................................................228 14.2.1 SCI Baud Rate Registers (SCIxBDH, SCIxBDL) ..........................................................228 14.2.2 SCI Control Register 1 (SCIxC1) ...................................................................................229 14.2.3 SCI Control Register 2 (SCIxC2) ...................................................................................230 14.2.4 SCI Status Register 1 (SCIxS1) ......................................................................................231 14.2.5 SCI Status Register 2 (SCIxS2) ......................................................................................233 14.2.6 SCI Control Register 3 (SCIxC3) ...................................................................................234 14.2.7 SCI Data Register (SCIxD) .............................................................................................235 14.3 Functional Description ..................................................................................................................235 14.3.1 Baud Rate Generation .....................................................................................................235 14.3.2 Transmitter Functional Description ................................................................................236 14.3.3 Receiver Functional Description ....................................................................................237 14.3.4 Interrupts and Status Flags ..............................................................................................239 14.3.5 Additional SCI Functions ...............................................................................................240 Chapter 15 16-Bit Serial Peripheral Interface (S08SPI16V1) 15.1 Introduction ...................................................................................................................................243 15.1.1 SPI Port Configuration Information ...............................................................................243 15.1.2 Features ...........................................................................................................................246 15.1.3 Modes of Operation ........................................................................................................246 15.1.4 Block Diagrams ..............................................................................................................246 15.2 External Signal Description ..........................................................................................................248 15.2.1 SPSCK — SPI Serial Clock ............................................................................................248 15.2.2 MOSI — Master Data Out, Slave Data In ......................................................................249 15.2.3 MISO — Master Data In, Slave Data Out ......................................................................249 15.2.4 SS — Slave Select ..........................................................................................................249 15.3 Register Definition ........................................................................................................................249 15.3.1 SPI Control Register 1 (SPIxC1) ....................................................................................249 15.3.2 SPI Control Register 2 (SPIxC2) ....................................................................................250 15.3.3 SPI Baud Rate Register (SPIxBR) ..................................................................................252 15.3.4 SPI Status Register (SPIxS) ............................................................................................253 15.3.5 SPI Data Registers (SPIxDH:SPIxDL) ...........................................................................254 15.3.6 SPI Match Registers (SPIxMH:SPIxML) .......................................................................255 15.4 Functional Description ..................................................................................................................256 15.4.1 General ............................................................................................................................256 15.4.2 Master Mode ...................................................................................................................256 15.4.3 Slave Mode .....................................................................................................................257 15.4.4 Data Transmission Length ..............................................................................................258 MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 15 15.4.5 SPI Clock Formats ..........................................................................................................259 15.4.6 SPI Baud Rate Generation ..............................................................................................261 15.4.7 Special Features ..............................................................................................................262 15.4.8 Error Conditions .............................................................................................................263 15.4.9 Low Power Mode Options ..............................................................................................264 15.4.10SPI Interrupts ..................................................................................................................265 15.5 Initialization/Application Information ..........................................................................................267 15.5.1 SPI Module Initialization Example .................................................................................267 Chapter 16 Timer/Pulse-Width Modulator (S08TPMV3) 16.1 Introduction ...................................................................................................................................271 16.1.1 Features ...........................................................................................................................273 16.1.2 Modes of Operation ........................................................................................................273 16.1.3 Block Diagram ................................................................................................................274 16.2 Signal Description .........................................................................................................................276 16.2.1 Detailed Signal Descriptions ..........................................................................................276 16.3 Register Definition ........................................................................................................................280 16.3.1 TPM Status and Control Register (TPMxSC) ................................................................280 16.3.2 TPM-Counter Registers (TPMxCNTH:TPMxCNTL) ....................................................281 16.3.3 TPM Counter Modulo Registers (TPMxMODH:TPMxMODL) ....................................282 16.3.4 TPM Channel n Status and Control Register (TPMxCnSC) ..........................................283 16.3.5 TPM Channel Value Registers (TPMxCnVH:TPMxCnVL) ..........................................285 16.4 Functional Description ..................................................................................................................286 16.4.1 Counter ............................................................................................................................287 16.4.2 Channel Mode Selection .................................................................................................288 16.5 Reset Overview .............................................................................................................................292 16.5.1 General ............................................................................................................................292 16.5.2 Description of Reset Operation .......................................................................................292 16.6 Interrupts .......................................................................................................................................292 16.6.1 General ............................................................................................................................292 16.6.2 Description of Interrupt Operation .................................................................................292 Chapter 17 Universal Serial Bus Device Controller (S08USBV1) 17.1 Introduction ...................................................................................................................................295 17.1.1 Clocking Requirements ...................................................................................................295 17.1.2 Current Consumption in USB Suspend ..........................................................................295 17.1.3 3.3 V Regulator ...............................................................................................................295 17.1.4 Features ...........................................................................................................................298 17.1.5 Modes of Operation ........................................................................................................298 17.1.6 Block Diagram ................................................................................................................299 17.2 External Signal Description ..........................................................................................................300 17.2.1 USBDP ............................................................................................................................300 17.2.2 USBDN ...........................................................................................................................300 MC9S08JM60 Series Data Sheet, Rev. 3 16 Freescale Semiconductor 17.2.3 VUSB33 ............................................................................................................................................................. 300 17.3 Register Definition ........................................................................................................................300 17.3.1 USB Control Register 0 (USBCTL0) .............................................................................301 17.3.2 Peripheral ID Register (PERID) .....................................................................................301 17.3.3 Peripheral ID Complement Register (IDCOMP) ............................................................302 17.3.4 Peripheral Revision Register (REV) ...............................................................................302 17.3.5 Interrupt Status Register (INTSTAT) ..............................................................................303 17.3.6 Interrupt Enable Register (INTENB) ..............................................................................304 17.3.7 Error Interrupt Status Register (ERRSTAT) ...................................................................305 17.3.8 Error Interrupt Enable Register (ERRENB) ...................................................................306 17.3.9 Status Register (STAT) ....................................................................................................307 17.3.10Control Register (CTL) ...................................................................................................308 17.3.11Address Register (ADDR) ..............................................................................................309 17.3.12Frame Number Register (FRMNUML, FRMNUMH) ...................................................309 17.3.13Endpoint Control Register (EPCTLn, n=0-6) .................................................................310 17.4 Functional Description ..................................................................................................................311 17.4.1 Block Descriptions ..........................................................................................................311 17.4.2 Buffer Descriptor Table (BDT) .......................................................................................316 17.4.3 USB Transactions ...........................................................................................................319 17.4.4 USB Packet Processing ...................................................................................................321 17.4.5 Start of Frame Processing ...............................................................................................322 17.4.6 Suspend/Resume .............................................................................................................323 17.4.7 Resets ..............................................................................................................................324 17.4.8 Interrupts .........................................................................................................................325 Chapter 18 Development Support 18.1 Introduction ...................................................................................................................................327 18.1.1 Features ...........................................................................................................................328 18.2 Background Debug Controller (BDC) ..........................................................................................328 18.2.1 BKGD Pin Description ...................................................................................................329 18.2.2 Communication Details ..................................................................................................330 18.2.3 BDC Commands .............................................................................................................334 18.2.4 BDC Hardware Breakpoint .............................................................................................336 18.3 On-Chip Debug System (DBG) ....................................................................................................337 18.3.1 Comparators A and B .....................................................................................................337 18.3.2 Bus Capture Information and FIFO Operation ...............................................................337 18.3.3 Change-of-Flow Information ..........................................................................................338 18.3.4 Tag vs. Force Breakpoints and Triggers .........................................................................338 18.3.5 Trigger Modes .................................................................................................................339 18.3.6 Hardware Breakpoints ....................................................................................................341 18.4 Register Definition ........................................................................................................................341 18.4.1 BDC Registers and Control Bits .....................................................................................341 18.4.2 System Background Debug Force Reset Register (SBDFR) ..........................................343 18.4.3 DBG Registers and Control Bits .....................................................................................344 MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 17 Appendix A Electrical Characteristics Introduction ....................................................................................................................................349 Parameter Classification.................................................................................................................349 Absolute Maximum Ratings...........................................................................................................349 Thermal Characteristics..................................................................................................................350 ESD Protection and Latch-Up Immunity .......................................................................................351 DC Characteristics..........................................................................................................................352 Supply Current Characteristics.......................................................................................................357 Analog Comparator (ACMP) Electricals .......................................................................................358 ADC Characteristics.......................................................................................................................358 External Oscillator (XOSC) Characteristics ..................................................................................362 MCG Specifications .......................................................................................................................363 AC Characteristics..........................................................................................................................364 A.12.1 Control Timing ................................................................................................................364 A.12.2 Timer/PWM (TPM) Module Timing ...............................................................................365 A.12.3 SPI Characteristics ...........................................................................................................366 A.13 Flash Specifications........................................................................................................................369 A.14 USB Electricals ..............................................................................................................................370 A.15 EMC Performance..........................................................................................................................370 A.15.1 Radiated Emissions..........................................................................................................370 A.1 A.2 A.3 A.4 A.5 A.6 A.7 A.8 A.9 A.10 A.11 A.12 Appendix B Ordering Information and Mechanical Drawings B.1 Ordering Information .....................................................................................................................373 B.2 Orderable Part Numbering System ................................................................................................373 B.3 Mechanical Drawings.....................................................................................................................373 MC9S08JM60 Series Data Sheet, Rev. 3 18 Freescale Semiconductor Chapter 1 Device Overview 1.1 Introduction MC9S08JM60 series MCUs are members of the low-cost, high-performance HCS08 Family of 8-bit microcontroller units (MCUs). All MCUs in the family use the enhanced HCS08 core and are available with a variety of modules, memory sizes, memory types, and package types. Table 1-1 summarizes the peripheral availability per package type for the devices available in the MC9S08JM60 series. Table 1-1. Devices in the MC9S08JM60 Series Device Feature MC9S08JM60 Package Flash RAM USB RAM ACMP ADC IIC IRQ KBI SCI1 SCI2 SPI1 SPI2 TPM1 TPM2 USB I/O pins Package types 51 64 QFP 64 LQFP 6-ch 8 12-ch 64-pin 48-pin 60,912 4096 256 yes 8-ch yes yes 7 yes yes yes yes 4-ch 2-ch yes 37 48 QFN 33 44 LQFP 51 64 QFP 64 LQFP 4-ch 6-ch 7 8 8-ch 12-ch 44-pin 64-pin MC9S08JM32 48-pin 32,768 2048 256 yes 8-ch yes yes 7 yes yes yes yes 4-ch 2-ch yes 37 48 QFN 33 44 LQFP 4-ch 7 8-ch 44-pin 1.2 MCU Block Diagram The block diagram in Figure 1-1 shows the structure of the MC9S08JM60 series MCU. MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 19 Chapter 1 Device Overview USBDP USBDN PORT A 6 PTA5– PTA0 PTB7/ADP7 PTB6/ADP6 PTB5/KBIP5/ADP5 PTB4/KBIP4/ADP4 PTB3/SS2/ADP3 PTB2/SPSCK2/ADP2 PTB1/MOSI2/ADP1 PTB0/MISO2/ADP0 PTC6 PTC5/RxD2 PTC4 PTC3/TxD2 PTC2 PTC1/SDA PTC0/SCL HCS08 CORE ON-CHIP ICE AND DEBUG MODULE (DBG) FULL SPEED USB USB ENDPOINT TRANSCEIVER RAM 8-/16-BIT SERIAL PERIPHERAL INTERFACE MODULE (SPI2) SS2 SPSCK2 MOSI2 MISO2 RxD2 TxD2 SDA SCL USB SIE BKGD/MS BDC CPU RESET HCS08 SYSTEM CONTROL RESETS AND INTERRUPTS MODES OF OPERATION POWER MANAGEMENT IRQ/TPMCLK SERIAL COMMUNICATIONS INTERFACE MODULE (SCI2) COP IRQ LVD IIC MODULE (IIC) VDDAD VSSAD VREFL VREFH USER Flash (IN BYTES) MC9S08JM60 = 60,912 MC9S08JM32 = 32,768 12-CHANNEL, 12-BIT ANALOG-TO-DIGITAL CONVERTER (ADC) 8 4 PORT D PORT C PORT B ACMP– ANALOG COMPARATOR (ACMP) ACMP+ ACMPO SS1 SPSCK1 MOSI1 MISO1 6-CHANNEL TIMER/PWM MODULE (TPM1) SERIAL COMMUNICATIONS INTERFACE MODULE (SCI1) PORT E TPMCLK TPM1CH1 TPM1CH0 TPM1CHx 4 RxD1 TxD1 TPMCLK TPM2CH1 TPM2CH0 KBIPx 8-BIT KEYBOARD INTERRUPT MODULE (KBI) KBIPx EXTAL XTAL PTD7 PTD6 PTD5 PTD4/ADP11 PTD3/KBIP3/ADP10 PTD2/KBIP2/ACMPO PTD1/ADP9/ACMP– PTD0/ADP8/ACMP+ PTE7/SS1 PTE6/SPSCK1 PTE5/MOSI1 PTE4/MISO1 PTE3/TPM1CH1 PTE2/TPM1CH0 PTE1/RxD1 PTE0/TxD1 PTF7 PTF6 PTF5/TPM2CH1 PTF4/TPM2CH0 PTF3/TPM1CH5 PTF2/TPM1CH4 PTF1/TPM1CH3 PTF0/TPM1CH2 PTG5/EXTAL PTG4/XTAL PTG3/KBIP7 PTG2/KBIP6 PTG1/KBIP1 PTG0/KBIP0 USER RAM (IN BYTES) MC9S08JM60 = 4096 MC9S08JM32 = 2048 8-/16-BIT SERIAL PERIPHERAL INTERFACE MODULE (SPI1) MULTI-PURPOSE CLOCK GENERATOR (MCG) VSSOSC LOW-POWER OSCILLATOR SYSTEM VOLTAGE REGULATOR USB 3.3-V VOLTAGE REGULATOR REAL-TIME COUNTER (RTC) VDD VSS MODULE (TPM2) VUSB33 4 4 NOTES: 1. Port pins are software configurable with pullup device if input port. 2. Pin contains software configurable pullup/pull-down device if IRQ is enabled (IRQPE = 1). Pull-down is enabled if rising edge detect is selected (IRQEDG = 1) 3. IRQ does not have a clamp diode to VDD. IRQ must not be driven above VDD. 4. Pin contains integrated pullup device. 5. When pin functions as KBI (KBIPEn = 1) and associated pin is configured to enable the pullup device, KBEDGn can be used to reconfigure the pullup as a pull-down device. Figure 1-1. MC9S08JM60 Series Block Diagram MC9S08JM60 Series Data Sheet, Rev. 3 20 Freescale Semiconductor PORT G PORT F 2-CHANNEL TIMER/PWM Chapter 1 Device Overview Table 1-2 lists the functional versions of the on-chip modules. Table 1-2. Versions of On-Chip Modules Module Analog Comparator Analog-to-Digital Converter Central Processing Unit IIC Module Keyboard Interrupt Multi-Purpose Clock Generator Real-Time Counter Serial Communications Interface 16-bit Serial Peripheral Interface Timer Pulse-Width Modulator Universal Serial Bus Debug Module (ACMP) (ADC) (CPU) (IIC) (KBI) (MCG) (RTC) (SCI) (SPI16) (TPM) (USB) (DBG) Version 2 1 2 2 2 1 1 4 1 3 1 2 1.3 System Clock Distribution Figure 1-2 shows a simplified clock connection diagram. Some modules in the MCU have selectable clock inputs as shown. The clock inputs to the modules indicate the clock(s) that are used to drive the module function. All memory mapped registers associated with the modules are clocked with BUSCLK. MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 21 Chapter 1 Device Overview TPMCLK 1 kHz LPO LPO clock MCGERCLK MCGIRCLK MCG MCGFFCLK FFCLK1 RTC COP TPM1 TPM2 IIC SCI1 SCI2 SPI1 SPI2 ÷2 BUSCLK MCGOUT MCGLCLK XOSC USB RAM ÷2 USB CPU BDC ADC2 RAM Flash3 EXTAL XTAL 1. The FFCLK is internally synchronized to the bus clock and must not exceed one half of the bus clock frequency. 2. ADC has min. and max. frequency requirements. See Chapter 10, “Analog-to-Digital Converter (S08ADC12V1),” and Appendix A, “Electrical Characteristics,” for details. 3. Flash has the frequency requirements for program and erase operation. See the Appendix A, “Electrical Characteristics,” for details. Figure 1-2. System Clock Distribution Diagram The MCG supplies the following clock sources: • MCGOUT — This clock source is used as the CPU, USB RAM and USB module clock, and is divided by two to generate the peripheral bus clock (BUSCLK). Control bits in the MCG control registers determine which of the three clock sources is connected: — Internal reference clock — External reference clock — Frequency-locked loop (FLL) or Phase-locked loop (PLL) output See Chapter 12, “Multi-Purpose Clock Generator (S08MCGV1),” for details on configuring the MCGOUT clock. • MCGLCLK — This clock source is derived from the digitally controlled oscillator (DCO) of the MCG. Development tools can select this internal self-clocked source to speed up BDC communications in systems where the bus clock is slow. • MCGIRCLK — This is the internal reference clock and can be selected as the real-time counter clock source. Chapter 12, “Multi-Purpose Clock Generator (S08MCGV1),” explains the MCGIRCLK in more detail. See Chapter 13, “Real-Time Counter (S08RTCV1),” for more information regarding the use of MCGIRCLK. • MCGERCLK — This is the external reference clock and can be selected as the clock source of real-time counter and ADC module. Section 12.4.6, “External Reference Clock,” explains the MCGERCLK in more detail. See Chapter 13, “Real-Time Counter (S08RTCV1),” and Chapter 10, MC9S08JM60 Series Data Sheet, Rev. 3 22 Freescale Semiconductor Chapter 1 Device Overview • • • “Analog-to-Digital Converter (S08ADC12V1),” for more information regarding the use of MCGERCLK with these modules. MCGFFCLK — This clock source is divided by 2 to generate FFCLK after being synchronized to the BUSCLK. It can be selected as clock source for the TPM modules. The frequency of the MCGFFCLK is determined by the settings of the MCG. See the Section 12.4.7, “Fixed Frequency Clock,” for details. LPO clock— This clock is generated from an internal Low Power Oscillator that is completely independent of the MCG module. The LPO clock can be selected as the clock source to the RTC or COP modules. See Chapter 13, “Real-Time Counter (S08RTCV1),” and Section 5.4, “Computer Operating Properly (COP) Watchdog,” for details on using the LPO clock with these modules. TPMCLK — TPMCLK is the optional external clock source for the TPM modules. The TPMCLK must be limited to 1/4th the frequency of the BUSCLK for synchronization. See Chapter 16, “Timer/Pulse-Width Modulator (S08TPMV3),” for more details. MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 23 Chapter 1 Device Overview MC9S08JM60 Series Data Sheet, Rev. 3 24 Freescale Semiconductor Chapter 2 Pins and Connections 2.1 Introduction This chapter describes signals that connect to package pins. It includes pinout diagrams, a table of signal properties, and detailed discussion of signals. MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 25 Chapter 2 Pins and Connections 2.2 Device Pin Assignment PTD3/KBIP3/ADP10 49 63 2 3 4 5 6 7 8 9 10 11 12 13 14 15 18 17 PTA2 PTA3 PTG0/KBIP0 PTG1/KBIP1 PTE7/SS1 PTE6/SPSCK1 PTE4/MISO1 PTE5/MOSI1 USBDN USBDP VUSB33 PTA0 PTA1 VDD VSS 19 20 21 22 23 24 25 26 27 28 29 30 31 32 PTA4 62 61 60 59 58 57 56 55 54 53 52 51 50 47 46 45 44 43 42 48 PTD2/KBIP2/ACMPO VSSAD VREFL VREFH VDDAD PTD1/ADP9/ACMP– PTD0/ADP8/ACMP+ PTB7/ADP7 PTB6/ADP6 PTB5/KBIP5/ADP5 PTB4/KBIP4/ADP4 PTB3/SS2/ADP3 PTB2/SPSCK2/ADP2 PTB1/MOSI2/ADP1 PTB0/MISO2/ADP0 33 PTA5 41 40 39 38 37 36 35 34 PTG5/EXTAL PTC3/TxD2 PTC1/SDA PTC2 64 PTC4 1 IRQ/TPMCLK RESET PTF0/TPM1CH2 PTF1/TPM1CH3 PTF2/TPM1CH4 PTF3/TPM1CH5 PTF4/TPM2CH0 PTC6 PTF7 PTF5/TPM2CH1 PTF6 PTE0/TxD1 PTE1/RxD1 PTE2/TPM1CH0 PTE3/TPM1CH1 16 64-Pin QFP/LQFP Figure 2-1. MC9S08JM60 in 64-Pin QFP/LQFP Package MC9S08JM60 Series Data Sheet, Rev. 3 26 Freescale Semiconductor PTD7 PTD6 PTD4/ADP11 PTG2/KBIP6 PTG3/KBIP7 PTC5/RxD2 PTG4/XTAL PTC0/SCL VSSOSC BKGD/MS PTD5 Chapter 2 Pins and Connections PTG5/EXTAL PTC3/TxD2 PTC1/SDA PTC2 PTG2/KBIP6 38 PTG3/KBIP7 PTC5/RxD2 PTG4/XTAL PTC0/SCL VSSOSC BKGD/MS 48 PTC4 1 IRQ/TPMCLK RESET PTF0/TPM1CH2 PTF1/TPM1CH3 PTF4/TPM2CH0 PTF5/TPM2CH1 PTF6 PTE0/TxD1 PTE1/RxD1 PTE2/TPM1CH0 PTE3/TPM1CH1 12 14 13 VSS PTE7/SS1 USBDN USBDP VDD PTG0/KBIP0 PTE6/SPSCK1 PTG1/KBIP1 PTE4/MISO1 PTE5/MOSI1 VUSB33 15 16 17 18 19 20 21 22 23 2 3 4 5 6 7 8 9 10 11 47 46 45 44 43 42 41 40 39 PTD7 37 36 PTD2/KBIP2/ACMPO 35 34 33 32 VSSAD/VREFL VDDAD/VREFH PTD1/ADP9/ACMP– PTD0/ADP8/ACMP+ PTB5/KBIP5/ADP5 PTB4/KBIP4/ADP4 PTB3/SS2/ADP3 PTB2/SPSCK2/ADP2 PTB1/MOSI2/ADP1 PTB0/MISO2/ADP0 25 PTA5 24 PTA0 31 30 29 28 27 26 48-Pin QFN Figure 2-2. MC9S08JM60 Series in 48-Pin QFN Package MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 27 Chapter 2 Pins and Connections PTG5/EXTAL PTC3/TxD2 PTC1/SDA PTC2 44 PTC4 1 IRQ/TPMCLK RESET PTF0/TPM1CH2 PTF1/TPM1CH3 PTF4/TPM2CH0 PTF5/TPM2CH1 PTE0/TxD1 PTE1/RxD1 PTE2/TPM1CH0 PTE3/TPM1CH1 11 13 12 VSS PTE7/SS1 USBDN USBDP VDD PTG0/KBIP0 PTE6/SPSCK1 PTE4/MISO1 PTE5/MOSI1 VUSB33 14 15 16 17 18 19 20 21 2 3 4 5 6 7 8 9 10 43 42 41 40 39 38 37 36 35 PTG2/KBIP6 34 33 PTD2/KBIP2/ACMPO 32 31 30 29 VSSAD/VREFL VDDAD/VREFH PTD1/ADP9/ACMP– PTD0/ADP8/ACMP+ PTB5/KBIP5/ADP5 PTB4/KBIP4/ADP4 PTB3/SS2/ADP3 PTB2/SPSCK2/ADP2 PTB1/MOSI2/ADP1 23 PTB0/MISO2/ADP0 22 PTG1/KBIP1 28 27 26 25 24 44-Pin LQFP Figure 2-3. MC9S08JM60 Series in 44-Pin LQFP Package 2.3 Recommended System Connections Figure 2-4 shows pin connections that are common to almost all MC9S08JM60 series application systems. MC9S08JM60 Series Data Sheet, Rev. 3 28 Freescale Semiconductor PTG3/KBIP7 PTC5/RxD2 PTG4/XTAL PTC0/SCL VSSOSC BKGD/MS Chapter 2 Pins and Connections CBYAD 0.1 μF SYSTEM POWER + 5V VDD CBLK + 10 μF VREFH MC9S08JM60 VDDAD PORT A PTA0–PTA5 VSSAD VREFL VDD CBY 0.1 μF VSS PTB0/MISO2/ADP0 PTB1/MOSI2/ADP1 PTB2/SPSCK2/ADP2 PORT B PTB3/SS2/ADP3 PTB4/KBIP4/ADP4 PTB5/KBIP5/ADP5 PTB6/ADP6 PTB7/ADP7 PTC0/SCL PTC1/SDA PTC2 PTC3/TxD2 PTC4 PTC5/RxD2 PTC6 I/O AND PTD0/ADP8/ACMP+ PTD1/ADP9/ACMP– PERIPHERAL PTD2/KBIP2/ACMPO PTD3/KBIP3/ADP10 INTERFACE TO PTD4/ADP11 APPLICATION PTD5 PTD6 SYSTEM PTD7 PTE0/TxD1 PTE1/RxD1 PTE2/TPM1CH0 PTE3/TPM1CH1 PTE4/MISO1 PTE5/MOSI1 PTE6/SPSCK1 PTE7/SS1 PTF0/TPM1CH2 PTF1/TPM1CH3 PTF2/TPM1CH4 PTF3/TPM1CH5 PTF4/TPM2CH0 PTF5/TPM2CH1 PTF6 PTF7 PTG0/KBIP0 PTG1/KBIP1 PTG2/KBIP6 PTG3/KBIP7 PTG4/XTAL PTG5/EXTAL NOTE 1 RF XTAL C1 X1 C2 RS VSSOSC EXTAL PORT C BACKGROUND HEADER VDD VDD 4.7 kΩ–10 kΩ 0.1 μF VDD OPTIONAL MANUAL RESET ASYNCHRONOUS INTERRUPT INPUT 3.3-V Reference + 4.7 μF 0.47 μF VUSB33 4.7 kΩ– 10 kΩ 0.1 μF RESET BKGD/MS PORT D IRQ PORT E USB SERIES-B CONNECTOR 2 3 1 4 VBus PORT F USBDN VUSB33 RPUDP USBDP PORT G NOTES: 1. External crystal circuity is not required if using the MCG internal clock option. For USB operation, an external crystal is required. 2. XTAL and EXTAL are the same pins as PTG4 and PTG5, respectively. 3. RC filters on RESET and IRQ are recommended for EMC-sensitive applications. 4. RPUDP is shown for full-speed USB only. The diagram shows a configuration where the on-chip regulator and RPUDP are enabled. The voltage regulator output is used for RPUDP. RPUDP can optionally be disabled if using an external pullup resistor on USBDP 5. VBUS is a 5.0-V supply from upstream port that can be used for USB operation 6. USBDP and USBDN are powered by the 3.3-V regulator or external 3.3-V supply on VUSB33. Figure 2-4. Basic System Connections MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 29 Chapter 2 Pins and Connections 2.3.1 Power (VDD, VSS, VSSOSC, VDDAD, VSSAD, VUSB33) VDD and VSS are the primary power supply pins for the MCU. This voltage source supplies power to all I/O buffer circuitry and to an internal voltage regulator. The internal voltage regulator provides regulated lower-voltage source to the CPU and other internal circuitry of the MCU. Typically, application systems have two separate capacitors across the power pins. In this case, there must be a bulk electrolytic capacitor, such as a 10-μF tantalum capacitor, to provide bulk charge storage for the overall system and a 0.1-μF ceramic bypass capacitor located as near to the paired VDD and VSS power pins as practical to suppress high-frequency noise. The MC9S08JM60 series have a VSSOSC pin. This pin must be connected to the system ground plane or to the primary VSS pin through a low-impedance connection. VDDAD and VSSAD are the analog power supply pins for the MCU. This voltage source supplies power to the ADC module. A 0.1-μF ceramic bypass capacitor must be located as near to the analog power pins as practical to suppress high-frequency noise. VUSB33 is connected to the internal USB 3.3-V regulator. VUSB33 maintains an output voltage of 3.3 V and can only source enough current for internal USB transceiver and USB pullup resistor. Two separate capacitors (4.7-μF bulk electrolytic stability capacitor and 0.47-μF ceramic bypass capacitors) must be connected across this pin to ground to decrease the output ripple of this voltage regulator when it is enabled. 2.3.2 Oscillator (XTAL, EXTAL) Immediately after reset, the MCU uses an internally generated clock provided by the multi-purpose clock generator (MCG) module. For more information on the MCG, see Chapter 12, “Multi-Purpose Clock Generator (S08MCGV1).” The oscillator (XOSC) in this MCU is a Pierce oscillator that can accommodate a crystal or ceramic resonator. Rather than a crystal or ceramic resonator, an external oscillator can be connected to the EXTAL input pin. RS (when used) and RF must be low-inductance resistors such as carbon composition resistors. Wire-wound resistors, and some metal film resistors, have too much inductance. C1 and C2 normally must be high-quality ceramic capacitors that are specifically designed for high-frequency applications. RF is used to provide a bias path to keep the EXTAL input in its linear range during crystal startup; its value is not generally critical. Typical systems use 1 MΩ to 10 MΩ. Higher values are sensitive to humidity and lower values reduce gain and (in extreme cases) could prevent startup. C1 and C2 are typically in the 5-pF to 25-pF range and are chosen to match the requirements of a specific crystal or resonator. Be sure to take into account printed circuit board (PCB) capacitance and MCU pin capacitance when selecting C1 and C2. The crystal manufacturer typically specifies a load capacitance which is the series combination of C1 and C2 (which are usually the same size). As a first-order approximation, use 10 pF as an estimate of combined pin and PCB capacitance for each oscillator pin (EXTAL and XTAL). MC9S08JM60 Series Data Sheet, Rev. 3 30 Freescale Semiconductor Chapter 2 Pins and Connections 2.3.3 RESET Pin RESET is a dedicated pin with a pullup device built in. It has input hysteresis, a high current output driver, and no output slew rate control. Internal power-on reset and low-voltage reset circuitry typically make external reset circuitry unnecessary. This pin is normally connected to the standard 6-pin background debug connector, so a development system can directly reset the MCU system. If desired, a manual external reset can be added by supplying a simple switch to ground (pull reset pin low to force a reset). Whenever any reset is initiated (whether from an external source or from an internal source, the RESET pin is driven low for approximately 66 bus cycles and released. The reset circuity decodes the cause of reset and records it by setting a corresponding bit in the system control reset status register (SRS). In EMC-sensitive applications, an external RC filter is recommended on the reset pin. See Figure 2-4 for an example. 2.3.4 Background/Mode Select (BKGD/MS) When in reset, the BKGD/MS pin functions as a mode select pin. Immediately after reset rises the pin functions as the background pin and can be used for background debug communication. While functioning as a background/mode select pin, the pin includes an internal pullup device, input hysteresis, a standard output driver, and no output slew rate control. If nothing is connected to this pin, the MCU will enter normal operating mode at the rising edge of reset. If a debug system is connected to the 6-pin standard background debug header, it can hold BKGD/MS low during the rising edge of reset which forces the MCU to active background mode. The BKGD pin is used primarily for background debug controller (BDC) communications using a custom protocol that uses 16 clock cycles of the target MCU’s BDC clock per bit time. The target MCU’s BDC clock could be as fast as the bus clock rate, so there must never be any significant capacitance connected to the BKGD/MS pin that could interfere with background serial communications. Although the BKGD pin is a pseudo open-drain pin, the background debug communication protocol provides brief, actively driven, high speedup pulses to ensure fast rise times. Small capacitances from cables and the absolute value of the internal pullup device play almost no role in determining rise and fall times on the BKGD pin. 2.3.5 ADC Reference Pins (VREFH, VREFL) The VREFH and VREFL pins are the voltage reference high and voltage reference low inputs respectively for the ADC module. 2.3.6 External Interrupt Pin (IRQ) The IRQ pin is the input source for the IRQ interrupt and is also the input for the BIH and BIL instructions. If the IRQ function is not enabled, this pin can be used for TPMCLK. In EMC-sensitive applications, an external RC filter is recommended on the IRQ pin. See Figure 2-4 for an example. MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 31 Chapter 2 Pins and Connections 2.3.7 USB Data Pins (USBDP, USBDN) The USBDP (D+) and USBDN (D–) pins are the analog input/output lines to/from full-speed internal USB transciever. An optional internal pullup resistor for the USBDP pin, RPUDP, is available. 2.3.8 General-Purpose I/O and Peripheral Ports The MC9S08JM60 series of MCUs support up to 51 general-purpose I/O pins, which are shared with on-chip peripheral functions (timers, serial I/O, ADC, keyboard interrupts, etc.). When a port pin is configured as a general-purpose output or a peripheral uses the port pin as an output, software can select one of two drive strengths and enable or disable slew rate control. When a port pin is configured as a general-purpose input or a peripheral uses the port pin as an input, software can enable a pullup device. For information about controlling these pins as general-purpose I/O pins, see the Chapter 6, “Parallel Input/Output.” For information about how and when on-chip peripheral systems use these pins, see the appropriate module chapter. Immediately after reset, all pins are configured as high-impedance general-purpose inputs with internal pullup devices disabled. MC9S08JM60 Series Data Sheet, Rev. 3 32 Freescale Semiconductor Chapter 2 Pins and Connections Table 2-1. Pin Availability by Package Pin-Count Pin Number 64 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 48 1 2 3 4 5 — — 6 — — 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 44 1 2 3 4 5 — — 6 — — 7 — 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 PTG0 PTG1 PTA0 PTA1 PTA2 PTA3 PTA4 KBIP0 KBIP1 PTF0 PTF1 PTF2 PTF3 PTF4 PTC6 PTF7 PTF5 PTF6 PTE0 PTE1 PTE2 PTE3 PTE4 PTE5 PTE6 PTE7 TxD1 RxD1 TPM1CH0 TPM1CH1 MISO1 MOSI1 SPSCK1 SS1 VDD VSS USBDN USBDP VUSB33 TPM2CH1 TPM1CH2 TPM1CH3 TPM1CH4 TPM1CH5 TPM2CH0 Lowest Highest Port Pin PTC4 IRQ TPMCLK RESET Alt1 Alt2 Pin Number 64 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 48 25 26 27 28 29 30 31 — — 32 33 34 23 24 25 26 27 28 — — 29 30 31 44 Lowest Highest Port Pin PTA5 PTB0 PTB1 PTB2 PTB3 PTB4 PTB5 PTB6 PTB7 PTD0 PTD1 MISO2 MOSI2 SPSCK2 SS2 KBIP4 KBIP5 ADP6 ADP7 ADP8 ADP9 ACMP+ ACMP– VDDAD VREFH VREFL VSSAD PTD2 PTD3 PTD4 PTD5 PTD6 PTD7 PTG2 PTG3 KBIP6 KBIP7 BKGD PTG4 PTG5 XTAL EXTAL VSSOSC PTC0 PTC1 PTC2 PTC3 PTC5 TxD2 RxD2 SCL SDA MS KBIP2 KBIP3 ADP11 ACMPO ADP10 ADP0 ADP1 ADP2 ADP3 ADP4 ADP5 Alt1 Alt2 35 36 — — — — 37 38 39 40 41 42 43 44 45 46 47 48 32 33 — — — — — 34 35 36 37 38 39 40 41 42 43 44 MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 33 Chapter 2 Pins and Connections NOTE When an alternative function is first enabled, it is possible to get a spurious edge to the module, user software must clear out any associated flags before interrupts are enabled. Table 2-1 illustrates the priority if multiple modules are enabled. The highest priority module will have control over the pin. Selecting a higher priority pin function with a lower priority function already enabled can cause spurious edges to the lower priority module. It is recommended that all modules that share a pin be disabled before enabling another module. MC9S08JM60 Series Data Sheet, Rev. 3 34 Freescale Semiconductor Chapter 3 Modes of Operation 3.1 Introduction The operating modes of the MC9S08JM60 series are described in this chapter. Entry into each mode, exit from each mode, and functionality while in each mode are described. 3.2 • • Features Active background mode for code development Wait mode: — CPU halts operation to conserve power — System clocks running — Full voltage regulation is maintained Stop modes: CPU and bus clocks stopped — Stop2: Partial power down of internal circuits; RAM and USB RAM contents retained — Stop3: All internal circuits powered for fast recovery; RAM, USB RAM, and register contents are retained • 3.3 Run Mode Run is the normal operating mode for the MC9S08JM60 series. This mode is selected upon the MCU exiting reset if the BKGD/MS pin is high. In this mode, the CPU executes code from internal memory with execution beginning at the address fetched from memory at 0xFFFE:0xFFFF after reset. 3.4 Active Background Mode The active background mode functions are managed through the background debug controller (BDC) in the HCS08 core. The BDC, together with the on-chip in-circuit emulator (ICE) debug module (DBG), provides the means for analyzing MCU operation during software development. Active background mode is entered in any of five ways: • When the BKGD/MS pin is low at the rising edge of reset • When a BACKGROUND command is received through the BKGD pin • When a BGND instruction is executed • When encountering a BDC breakpoint • When encountering a DBG breakpoint MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 35 Chapter 3 Modes of Operation After entering active background mode, the CPU is held in a suspended state waiting for serial background commands rather than executing instructions from the user application program. Background commands are of two types: • Non-intrusive commands, defined as commands that can be issued while the user program is running. Non-intrusive commands can be issued through the BKGD pin while the MCU is in run mode; non-intrusive commands can also be executed when the MCU is in the active background mode. Non-intrusive commands include: — Memory access commands — Memory-access-with-status commands — BDC register access commands — The BACKGROUND command • Active background commands, which can only be executed while the MCU is in active background mode. Active background commands include commands to: — Read or write CPU registers — Trace one user program instruction at a time — Leave active background mode to return to the user application program (GO) The active background mode is used to program a bootloader or user application program into the flash program memory before the MCU is operated in run mode for the first time. When the MC9S08JM60 series is shipped from the Freescale factory, the flash program memory is erased by default unless specifically noted, so there is no program that could be executed in run mode until the flash memory is initially programmed. The active background mode can also be used to erase and reprogram the flash memory after it has been previously programmed. For additional information about the active background mode, refer to Chapter 18, “Development Support.” 3.5 Wait Mode Wait mode is entered by executing a WAIT instruction. Upon execution of the WAIT instruction, the CPU enters a low-power state in which it is not clocked. The I bit in the condition code register (CCR) is cleared when the CPU enters wait mode, enabling interrupts. When an interrupt request occurs, the CPU exits wait mode and resumes processing, beginning with the stacking operations leading to the interrupt service routine. While the MCU is in wait mode, there are some restrictions on which background debug commands can be used. • Only the BACKGROUND command and memory-access-with-status commands are available while the MCU is in wait mode. • The memory-access-with-status commands do not allow memory access, but they report an error indicating that the MCU is in stop or wait mode. • The BACKGROUND command can be used to wake the MCU from wait mode and enter active background mode. MC9S08JM60 Series Data Sheet, Rev. 3 36 Freescale Semiconductor Chapter 3 Modes of Operation 3.6 Stop Modes One of two stop modes is entered upon execution of a STOP instruction when STOPE in SOPT1 is set. In any stop mode, the bus and CPU clocks are halted. The MCG module can be configured to leave the reference clocks running. See Chapter 12, “Multi-Purpose Clock Generator (S08MCGV1),” for more information. Table 3-1 shows all of the control bits that affect stop mode selection and the mode selected under various conditions. The selected mode is entered following the execution of a STOP instruction. Table 3-1. Stop Mode Selection STOPE 0 1 1 1 1 1 ENBDM 1 x 1 0 0 0 LVDE x x LVDSE PPDC x x x 0 1 Stop Mode Stop modes disabled; illegal opcode reset if STOP instruction executed Stop3 with BDM enabled 2 Stop3 with voltage regulator active Stop3 Stop2 Both bits must be 1 Either bit a 0 Either bit a 0 ENBDM is located in the BDCSCR which is only accessible through BDC commands, see Section 18.4.1.1, “BDC Status and Control Register (BDCSCR).” 2 When in stop3 mode with BDM enabled, The SIDD will be near RIDD levels because internal clocks are enabled. 3.6.1 Stop3 Mode Stop3 mode is entered by executing a STOP instruction under the conditions as shown in Table 3-1. The states of all of the internal registers and logic, RAM contents, and I/O pin states are maintained. Stop3 can be exited by asserting RESET, or by an interrupt from one of the following sources: the real-time clock (RTC) interrupt, the USB resume interrupt, LVD, ADC, IRQ, KBI, SCI, or the ACMP. If stop3 is exited by means of the RESET pin, then the MCU is reset and operation will resume after taking the reset vector. Exit by means of one of the internal interrupt sources results in the MCU taking the appropriate interrupt vector. 3.6.1.1 LVD Enabled in Stop Mode The LVD system is capable of generating either an interrupt or a reset when the supply voltage drops below the LVD voltage. If the LVD is enabled in stop (LVDE and LVDSE bits in SPMSC1 both set) at the time the CPU executes a STOP instruction, then the voltage regulator remains active during stop mode. If the user attempts to enter stop2 with the LVD enabled for stop, the MCU will enter stop3 instead. For the ADC to operate, the LVD must be left enabled when entering stop3. For the ACMP to operate when ACGBS in ACMPSC is set, the LVD must be left enabled when entering stop3. For the XOSC to operate with an external reference when RANGE in MCGC2 is set, the LVD must be left enabled when entering stop3. MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 37 Chapter 3 Modes of Operation 3.6.1.2 Active BDM Enabled in Stop Mode Entry into the active background mode from run mode is enabled if ENBDM in BDCSCR is set. This register is described in Chapter 18, “Development Support.” If ENBDM is set when the CPU executes a STOP instruction, the system clocks to the background debug logic remain active when the MCU enters stop mode. Because of this, background debug communication remains possible. In addition, the voltage regulator does not enter its low-power standby state but maintains full internal regulation. If the user attempts to enter stop2 with ENBDM set, the MCU will enter stop3 instead. Most background commands are not available in stop mode. The memory-access-with-status commands do not allow memory access, but they report an error indicating that the MCU is in stop or wait mode. The BACKGROUND command can be used to wake the MCU from stop and enter active background mode if the ENBDM bit is set. After entering background debug mode, all background commands are available. 3.6.2 Stop2 Mode Stop2 mode is entered by executing a STOP instruction under the conditions as shown in Table 3-1. Most of the internal circuitry of the MCU is powered off in stop2, with the exception of the RAM. Upon entering stop2, all I/O pin control signals are latched so that the pins retain their states during stop2. Exit from stop2 is performed by asserting either wake-up pin: RESET or IRQ/TPMCLK. NOTE IRQ/TPMCLK always functions as an active-low wakeup input when the MCU is in stop2, regardless of how the pin is configured before entering stop2. It must be configured as an input before executing a STOP instruction to avoid an immediate exit from stop2. This pin must be driven or pulled high externally while in stop2 mode. In addition, the RTC interrupt can wake the MCU from stop2, if enabled. Upon wake-up from stop2 mode, the MCU starts up as from a power-on reset (POR): • All module control and status registers are reset • The LVD reset function is enabled and the MCU remains in the reset state if VDD is below the LVD trip point (low trip point selected due to POR) • The CPU takes the reset vector In addition to the above, upon waking up from stop2, the PPDF bit in SPMSC2 is set. This flag is used to direct user code to go to a stop2 recovery routine. PPDF remains set and the I/O pin states remain latched until a 1 is written to PPDACK in SPMSC2. To maintain I/O states for pins that were configured as general-purpose I/O before entering stop2, the user must restore the contents of the I/O port registers, which have been saved in RAM, to the port registers before writing to the PPDACK bit. If the port registers are not restored from RAM before writing to PPDACK, then the pins will switch to their reset states when PPDACK is written. For pins that were configured as peripheral I/O, the user must reconfigure the peripheral module that interfaces to the pin before writing to the PPDACK bit. If the peripheral module is not enabled before MC9S08JM60 Series Data Sheet, Rev. 3 38 Freescale Semiconductor Chapter 3 Modes of Operation writing to PPDACK, the pins will be controlled by their associated port control registers when the I/O latches are opened. 3.6.3 On-Chip Peripheral Modules in Stop Modes When the MCU enters any stop mode, system clocks to the internal peripheral modules are stopped. Even in the exception case (ENBDM = 1), where clocks to the background debug logic continue to operate, clocks to the peripheral systems are halted to reduce power consumption. Refer to Section 3.6.2, “Stop2 Mode,” and Section 3.6.1, “Stop3 Mode,” for specific information on system behavior in stop modes. Table 3-2. Stop Mode Behavior Mode Peripheral Stop2 CPU RAM Flash Parallel Port Registers ADC ACMP MCG IIC RTC SCI SPI TPM System Voltage Regulator XOSC I/O Pins USB (SIE and Transceiver) USB 3.3-V Regulator USB RAM 1 2 3 4 5 6 Stop3 Standby Standby Standby Standby Optionally On1 Optionally On2 Optionally On3 Standby on4 Optionally on4 Standby Standby Standby Standby Optionally On5 States Held Optionally On6 Standby Standby Off Standby Off Off Off Off Off Off Optionally Off Off Off Off Off States Held Off Off Standby Requires the asynchronous ADC clock and LVD to be enabled, else in standby. If ACGBS in ACMPSC is set, LVD must be enabled, else in standby. IRCLKEN and IREFSTEN set in MCGC1, else in standby. RTCPS[3:0] in RTCSC does not equal 0 before entering stop, else off. ERCLKEN and EREFSTEN set in MCGC2, else in standby. For high frequency range (RANGE in MCGC2 set) requires the LVD to also be enabled in stop3. USBEN in CTL is set and USBPHYEN in USBCTL0 is set, else off. MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 39 Chapter 3 Modes of Operation MC9S08JM60 Series Data Sheet, Rev. 3 40 Freescale Semiconductor Chapter 4 Memory 4.1 MC9S08JM60 Series Memory Map Figure 4-1 shows the memory map for the MC9S08JM60 series. On-chip memory in the MC9S08JM60 series of MCUs consists of RAM, flash program memory for nonvolatile data storage, plus I/O and control/status registers. The registers are divided into three groups: • Direct-page registers (0x0000 through 0x00AF) • High-page registers (0x1800 through 0x185F) • Nonvolatile registers (0xFFB0 through 0xFFBF) MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 41 Chapter 4 Memory 0x0000 0x00AF 0x00B0 0x0000 0x00AF 0x00B0 0x08AF 0x08B0 DIRECT PAGE REGISTERS RAM 4096 BYTES DIRECT PAGE REGISTERS RAM 2048 BYTES UNIMPLEMENTED 0x10AF 0x10B0 0x17FF 0x1800 0x185F 0x1860 FLASH 1872 BYTES HIGH PAGE REGISTERS 96 BYTES USB RAM — 256 BYTES 0x17FF 0x1800 0x185F 0x1860 3936 BYTES HIGH PAGE REGISTERS 96 BYTES USB RAM — 256 BYTES 0x195F 0x1960 0x195F 0x1960 UNIMPLEMENTED 0x7FFF 0x8000 FLASH 59,088 BYTES FLASH 32,768 BYTES 0xFFFF 0xFFFF MC9S08JM60 MC9S08JM32 Figure 4-1. MC9S08JM60 Series Memory Map 4.1.1 Reset and Interrupt Vector Assignments Figure 4-1 shows address assignments for reset and interrupt vectors. The vector names shown in this table are the labels used in the Freescale-provided equate file for the MC9S08JM60 series. For more details about resets, interrupts, interrupt priority, and local interrupt mask controls, refer to Chapter 5, “Resets, Interrupts, and System Configuration.” Table 4-1. Reset and Interrupt Vectors Address (High/Low) 0xFFC0:0xFFC1 to 0xFFC2:FFC3 0xFFC4:FFC5 0xFFC6:FFC7 0xFFC8:FFC9 Vector Vector Name Unused Vector Space RTC IIC ACMP Vrtc Viic Vacmp MC9S08JM60 Series Data Sheet, Rev. 3 42 Freescale Semiconductor Chapter 4 Memory Table 4-1. Reset and Interrupt Vectors (continued) Address (High/Low) 0xFFCA:FFCB 0xFFCC:FFCD 0xFFCE:FFCF 0xFFD0:FFD1 0xFFD2:FFD3 0xFFD4:FFD5 0xFFD6:FFD7 0xFFD8:FFD9 0xFFDA:FFDB 0xFFDC:FFDD 0xFFDE:FFDF 0xFFE0:FFE1 0xFFE2:FFE3 0xFFE4:FFE5 0xFFE6:FFE7 0xFFE8:FFE9 0xFFEA:FFEB 0xFFEC:FFED 0xFFEE:FFEF 0xFFF0:FFF1 0xFFF2:FFF3 0xFFF4:FFF5 0xFFF6:FFF7 0xFFF8:FFF9 0xFFFA:FFFB 0xFFFC:FFFD 0xFFFE:FFFF Vector ADC Conversion KBI SCI2 Transmit SCI2 Receive SCI2 Error SCI1 Transmit SCI1 Receive SCI1 Error TPM2 Overflow TPM2 Channel 1 TPM2 Channel 0 TPM1 Overflow TPM1 Channel 5 TPM1 Channel 4 TPM1 Channel 3 TPM1 Channel 2 TPM1 Channel 1 TPM1 Channel 0 Reserved USB Status SPI2 SPI1 MCG Loss of Lock Low Voltage Detect IRQ SWI Reset Vector Name Vadc Vkeyboard Vsci2tx Vsci2rx Vsci2err Vsci1tx Vsci1rx Vsci1err Vtpm2ovf Vtpm2ch1 Vtpm2ch0 Vtpm1ovf Vtpm1ch5 Vtpm1ch4 Vtpm1ch3 Vtpm1ch2 Vtpm1ch1 Vtpm1ch0 — Vusb Vspi2 Vspi1 Vlol Vlvd Virq Vswi Vreset 4.2 Register Addresses and Bit Assignments The registers in the MC9S08JM60 series are divided into these three groups: • Direct-page registers are located in the first 176 locations in the memory map, so they are accessible with efficient direct addressing mode instructions. • High-page registers are used much less often, so they are located above 0x1800 in the memory map. This leaves more room in the direct page for more frequently used registers and variables. • The nonvolatile register area consists of a block of 16 locations in flash memory at 0xFFB0–0xFFBF. Nonvolatile register locations include: — Three values which are loaded into working registers at reset MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 43 Chapter 4 Memory — An 8-byte backdoor comparison key which optionally allows a user to gain controlled access to secure memory Because the nonvolatile register locations are flash memory, they must be erased and programmed like other flash memory locations. Direct-page registers can be accessed with efficient direct addressing mode instructions. Bit manipulation instructions can be used to access any bit in any direct-page register. Table 4-2 is a summary of all user-accessible direct-page registers and control bits. The direct page registers in Table 4-2 can use the more efficient direct addressing mode which only requires the lower byte of the address. Because of this, the lower byte of the address in column one is shown in bold text. In Table 4-3 and Table 4-4, the whole address in column one is shown in bold. In Table 4-2, Table 4-3, and Table 4-4, the register names in column two are shown in bold to set them apart from the bit names to the right. Cells that are not associated with named bits are shaded. A shaded cell with a 0 indicates this unused bit always reads as a 0. Shaded cells with dashes indicate unused or reserved bit locations that could read as 1s or 0s. MC9S08JM60 Series Data Sheet, Rev. 3 44 Freescale Semiconductor Chapter 4 Memory Table 4-2. Direct-Page Register Summary (Sheet 1 of 4) Address 0x0000 0x0001 0x0002 0x0003 0x0004 0x0005 0x0006 0x0007 0x0008 0x0009 0x000A 0x000B 0x000C 0x000D 0x000E 0x000F 0x0010 0x0011 0x0012 0x0013 0x0014 0x0015 0x0016 0x0017 0x0018 Register Name PTAD PTADD PTBD PTBDD PTCD PTCDD PTDD PTDDD PTED PTEDD PTFD PTFDD PTGD PTGDD ACMPSC Reserved ADCSC1 ADCSC2 ADCRH ADCRL ADCCVH ADCCVL ADCCFG APCTL1 APCTL2 Bit 7 — — PTBD7 PTBDD7 — — PTDD7 PTDDD7 PTED7 PTEDD7 PTFD7 PTFDD7 — — ACME — COCO ADACT 0 ADR7 0 ADCV7 ADLPC ADPC7 — — 0 0 KBIPE7 KBEDG7 — TOF Bit 15 Bit 7 Bit 15 Bit 7 CH0F Bit 15 Bit 7 CH1F Bit 15 ADPC6 — — IRQPDD 0 KBIPE6 KBEDG6 — TOIE 14 6 14 6 CH0IE 14 6 CH1IE 14 6 — — PTBD6 PTBDD6 PTCD6 PTCDD6 PTDD6 PTDDD6 PTED6 PTEDD6 PTFD6 PTFDD6 — — ACBGS — AIEN ADTRG 0 ADR6 0 ADCV6 ADIV ADPC5 — — IRQEDG 0 KBIPE5 KBEDG5 — CPWMS 13 5 13 5 MS0B 13 5 MS1B 13 5 PTAD5 PTADD5 PTBD5 PTBDD5 PTCD5 PTCDD5 PTDD5 PTDDD5 PTED5 PTEDD5 PTFD5 PTFDD5 PTGD5 PTGDD5 ACF — ADCO ACFE 0 ADR5 0 ADCV5 ACFGT 0 ADR4 0 ADCV4 ADLSMP ADPC4 — — IRQPE 0 KBIPE4 KBEDG4 — CLKSB 12 4 12 4 MS0A 12 4 MS1A 12 0 ADR11 ADR3 ADCV11 ADCV3 ADPC3 ADPC11 — IRQF KBF KBIPE3 KBEDG3 — CLKSA 11 3 11 3 ELS0B 11 3 ELS1B 11 4 PTAD4 PTADD4 PTBD4 PTBDD4 PTCD4 PTCDD4 PTDD4 PTDDD4 PTED4 PTEDD4 PTFD4 PTFDD4 PTGD4 PTGDD4 ACIE — 3 PTAD3 PTADD3 PTBD3 PTBDD3 PTCD3 PTCDD3 PTDD3 PTDDD3 PTED3 PTEDD3 PTFD3 PTFDD3 PTGD3 PTGDD3 ACO — 2 PTAD2 PTADD2 PTBD2 PTBDD2 PTCD2 PTCDD2 PTDD2 PTDDD2 PTED2 PTEDD2 PTFD2 PTFDD2 PTGD2 PTGDD2 ACOPE — ADCH 0 ADR10 ADR2 ADCV10 ADCV2 ADPC2 ADPC10 — IRQACK KBACK KBIPE2 KBEDG2 — PS2 10 2 10 2 ELS0A 10 2 ELS1A 10 R ADR9 ADR1 ADCV9 ADCV1 ADPC1 ADPC9 — IRQIE KBIE KBIPE1 KBEDG1 — PS1 9 1 9 1 0 9 1 0 9 R ADR8 ADR0 ADCV8 ADCV0 ADPC0 ADPC8 — IRQMOD KBMOD KBIPE0 KBEDG0 — PS0 Bit 8 Bit 0 Bit 8 Bit 0 0 Bit 8 Bit 0 0 Bit 8 — 1 PTAD1 PTADD1 PTBD1 PTBDD1 PTCD1 PTCDD1 PTDD1 PTDDD1 PTED1 PTEDD1 PTFD1 PTFDD1 PTGD1 PTGDD1 Bit 0 PTAD0 PTADD0 PTBD0 PTBDD0 PTCD0 PTCDD0 PTDD0 PTDDD0 PTED0 PTEDD0 PTFD0 PTFDD0 PTGD0 PTGDD0 — ACMOD MODE ADICLK 0x0019– Reserved 0x001A 0x001B 0x001C 0x001D 0x001E 0x001F 0x0020 0x0021 0x0022 0x0023 0x0024 0x0025 0x0026 0x0027 0x0028 0x0029 IRQSC KBISC KBIPE KBIES Reserved TPM1SC TPM1CNTH TPM1CNTL TPM1MODH TPM1MODL TPM1C0SC TPM1C0VH TPM1C0VL TPM1C1SC TPM1C1VH MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 45 Chapter 4 Memory Table 4-2. Direct-Page Register Summary (Sheet 2 of 4) Address 0x002A 0x002B 0x002C 0x002D 0x002E 0x002F 0x0030 0x0031 0x0032 0x0033 0x0034 0x0035 0x0036 0x0037 0x0038 0x0039 0x003A 0x003B 0x003C 0x003D 0x003E 0x003F 0x0040 0x0041 0x0042 0x0043 0x0044 0x0045 0x0046 0x0047 0x0048 0x0049 0x004A 0x004B 0x004C 0x004D Register Name TPM1C1VL TPM1C2SC TPM1C2VH TPM1C2VL TPM1C3SC TPM1C3VH TPM1C3VL TPM1C4SC TPM1C4VH TPM1C4VL TPM1C5SC TPM1C5VH TPM1C5VL Reserved SCI1BDH SCI1BDL SCI1C1 SCI1C2 SCI1S1 SCI1S2 SCI1C3 SCI1D SCI2BDH SCI2BDL SCI2C1 SCI2C2 SCI2S1 SCI2S2 SCI2C3 SCI2D MCGC1 MCGC2 MCGTRM MCGSC MCGC3 MCGT LOLS LOLIE 0 — SPIE SPMIE 0 SPRF LOCK PLLS 0 — SPE SPIMODE SPPR2 SPMF PLLST CME 0 — SPTIE 0 SPPR1 SPTEF 0 0 — MSTR MODFEN SPPR0 MODF 0 — CPOL BIDIROE 0 0 0 — CPHA 0 SPR2 0 Bit 7 Bit 7 CH2F Bit 15 Bit 7 CH3F Bit 15 Bit 7 CH4F Bit 15 Bit 7 CH5F Bit 15 Bit 7 — LBKDIE SBR7 LOOPS TIE TDRE LBKDIF R8 Bit 7 LBKDIE SBR7 LOOPS TIE TDRE LBKDIF R8 Bit 7 CLKS BDIV RANGE 6 6 CH2IE 14 6 CH3IE 14 6 CH4IE 14 6 CH5IE 14 6 — RXEDGIE SBR6 SCISWAI TCIE TC RXEDGIF T8 6 RXEDGIE SBR6 SCISWAI TCIE TC RXEDGIF T8 6 5 5 MS2B 13 5 MS3B 13 5 MS4B 13 5 MS5B 13 5 — 0 SBR5 RSRC RIE RDRF 0 TXDIR 5 0 SBR5 RSRC RIE RDRF 0 TXDIR 5 4 4 MS2A 12 4 MS3A 12 4 MS4A 12 4 MS5A 12 4 — SBR12 SBR4 M ILIE IDLE RXINV TXINV 4 SBR12 SBR4 M ILIE IDLE RXINV TXINV 4 RDIV HGO TRIM IREFST CLKST OSCINIT VDIV 0 — SSOE SPISWAI SPR1 0 0 — LSBFE SPC0 SPR0 0 FTRIM LP 3 3 ELS2B 11 3 ELS3B 11 3 ELS4B 11 3 ELS5B 11 3 — SBR11 SBR3 WAKE TE OR RWUID ORIE 3 SBR11 SBR3 WAKE TE OR RWUID ORIE 3 2 2 ELS2A 10 2 ELS3A 10 2 ELS4A 10 2 ELS5A 10 2 — SBR10 SBR2 ILT RE NF BRK13 NEIE 2 SBR10 SBR2 ILT RE NF BRK13 NEIE 2 IREFS EREFS 1 1 0 9 1 0 9 1 0 9 1 0 9 1 — SBR9 SBR1 PE RWU FE LBKDE FEIE 1 SBR9 SBR1 PE RWU FE LBKDE FEIE 1 IRCLKEN Bit 0 Bit 0 0 Bit 8 Bit 0 0 Bit 8 Bit 0 0 Bit 8 Bit 0 0 Bit 8 Bit 0 — SBR8 SBR0 PT SBK PF RAF PEIE Bit 0 SBR8 SBR0 PT SBK PF RAF PEIE Bit 0 IREFSTEN ERCLKEN EREFSTEN 0x004E– Reserved 0x004F 0x0050 0x0051 0x0052 0x0053 SPI1C1 SPI1C2 SPI1BR SPI1S MC9S08JM60 Series Data Sheet, Rev. 3 46 Freescale Semiconductor Chapter 4 Memory Table 4-2. Direct-Page Register Summary (Sheet 3 of 4) Address 0x0054 0x0055 0x0056 0x0057 0x0058 0x0059 0x005A 0x005B 0x005C 0x005D Register Name SPI1DH SPI1DL SPI1MH SPI1ML IICA IICF IICC1 IICS IICD IICC2 GCAEN — TOF Bit 15 Bit 7 Bit 15 Bit 7 CH0F Bit 15 Bit 7 CH1F Bit 15 Bit 7 — RTIF ADEXT — TOIE 14 6 14 6 CH0IE 14 6 CH1IE 14 6 — RTCLKS 0 — CPWMS 13 5 13 5 MS0B 13 5 MS1B 13 5 — 0 — CLKSB 12 4 12 4 MS0A 12 4 MS1A 12 4 — RTIE RTCCNT RTCMOD — SPIE SPMIE 0 SPRF Bit 15 Bit 7 Bit 15 Bit 7 — USBRESET — 0 — SPE SPIMODE SPPR2 SPMF 14 6 14 6 — USBPU — 0 — SPTIE 0 SPPR1 SPTEF 13 5 13 5 — USBRESMEN — ID5 — MSTR MODFEN SPPR0 MODF 12 4 12 4 — LPRESF — ID4 — CPOL BIDIROE 0 0 11 3 11 3 — — — ID3 — CPHA 0 SPR2 0 10 2 10 2 — USBVREN — ID2 — SSOE SPISWAI SPR1 0 9 1 9 1 — — — ID1 — LSBFE SPC0 SPR0 0 Bit 8 Bit 0 Bit 8 Bit 0 — USBPHYEN — ID0 IICEN TCF Bit 7 Bit 15 Bit 7 Bit 15 Bit 7 AD7 MULT IICIE IAAS MST BUSY TX ARBL DATA 0 — CLKSA 11 3 11 3 ELS0B 11 3 ELS1B 11 3 — AD10 — PS2 10 2 10 2 ELS0A 10 2 ELS1A 10 2 — RTCPS AD9 — PS1 9 1 9 1 0 9 1 0 9 1 — AD8 — PS0 Bit 8 Bit 0 Bit 8 Bit 0 0 Bit 8 Bit 0 0 Bit 8 Bit 0 — TXAK 0 6 14 6 14 6 AD6 5 13 5 13 5 AD5 4 12 4 12 4 AD4 3 11 3 11 3 AD3 ICR RSTA SRW 0 IICIF 0 RXAK 2 10 2 10 2 AD2 1 9 1 9 1 AD1 Bit 0 Bit 8 Bit 0 Bit 8 Bit 0 0 0x005E– Reserved 0x005F 0x0060 0x0061 0x0062 0x0063 0x0064 0x0065 0x0066 0x0067 0x0068 0x0069 0x006A 0x006B 0x006C 0x006D 0x006E 0x006F 0x0070 0x0071 0x0072 0x0073 0x0074 0x0075 0x0076 0x0077 TPM2SC TPM2CNTH TPM2CNTL TPM2MODH TPM2MODL TPM2C0SC TPM2C0VH TPM2C0VL TPM2C1SC TPM2C1VH TPM2C1VL Reserved RTCSC RTCCNT RTCMOD Reserved SPI2C1 SPI2C2 SPI2BR SPI2S SPI2DH SPI2DL SPI2MH SPI2ML 0x0078– Reserved 0x007F 0x0080 USBCTL0 0x0081– Reserved 0x0087 0x0088 PERID MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 47 Chapter 4 Memory Table 4-2. Direct-Page Register Summary (Sheet 4 of 4) Address 0x0089 0x008A Register Name IDCOMP REV Bit 7 1 REV7 — STALLF STALL BTSERRF BTSERR — — FRM7 0 — — — — — — — — — 6 1 REV6 — — — — — — ADDR6 FRM6 0 — — — — — — — — — 5 NID5 REV5 — RESUMEF RESUME BUFERRF BUFERR ENDP TSUSPEND ADDR5 FRM5 0 — 0 0 0 0 0 0 0 — — ADDR4 FRM4 0 — EPCTLDIS EPCTLDIS EPCTLDIS EPCTLDIS EPCTLDIS EPCTLDIS EPCTLDIS — 4 NID4 REV4 — SLEEPF SLEEP BTOERRF BTOERR 3 NID3 REV3 — TOKDNEF TOKDNE DFN8F DFN8 IN — ADDR3 FRM3 0 — EPRXEN EPRXEN EPRXEN EPRXEN EPRXEN EPRXEN EPRXEN — 2 NID2 REV2 — SOFTOKF SOFTOK CRC16F CRC16 ODD CRESUME ADDR2 FRM2 FRM10 — EPTXEN EPTXEN EPTXEN EPTXEN EPTXEN EPTXEN EPTXEN — 1 NID1 REV1 — ERRORF ERROR CRC5F CRC5 0 ODDRST ADDR1 FRM1 FRM9 — EPSTALL EPSTALL EPSTALL EPSTALL EPSTALL EPSTALL EPSTALL — Bit 0 NID0 REV0 — USBRSTF USBRST PIDERRF PIDERR 0 USBEN ADDR0 FRM0 FRM8 — EPHSHK EPHSHK EPHSHK EPHSHK EPHSHK EPHSHK EPHSHK — 0x008B– Reserved 0x008F 0x0090 0x0091 0x0092 0x0093 0x0094 0x0095 0x0096 0x0097 0x0098 INTSTAT INTENB ERRSTAT ERRENB STAT CTL ADDR FRMNUML FRMNUMH 0x0099– Reserved 0x009C 0x009D 0x009E 0x009F 0x00A0 0x00A1 0x00A2 0x00A3 EPCTL0 EPCTL1 EPCTL2 EPCTL3 EPCTL4 EPCTL5 EPCTL6 0x00A4– Reserved 0x00AF High-page registers, shown in Table 4-3, are accessed much less often than other I/O and control registers so they have been located outside the direct addressable memory space, starting at 0x1800. Table 4-3. High-Page Register Summary (Sheet 1 of 3) Address 0x1800 0x1801 0x1802 0x1803 0x1804– 0x1805 0x1806 0x1807 0x1808 0x1809 0x180A 0x180B– 0x180F Register Name SRS SBDFR SOPT1 SOPT2 Reserved SDIDH SDIDL Reserved SPMSC1 SPMSC2 Reserved Bit 7 POR 0 COPT COPCLKS — — ID7 — LVWF — — COPW — — ID6 — LVWACK — — 6 PIN 0 5 COP 0 STOPE 0 — — ID5 — LVWIE LVDV — 4 ILOP 0 — 0 — — ID4 — LVDRE LVWV — 3 0 0 0 0 — ID11 ID3 — LVDSE PPDF — 2 LOC 0 0 SPI1FE — ID10 ID2 — LVDE PPDACK — 1 LVD 0 — SPI2FE — ID9 ID1 — 01 — — Bit 0 — BDFR — ACIC — ID8 ID0 — BGBE PPDC — MC9S08JM60 Series Data Sheet, Rev. 3 48 Freescale Semiconductor Chapter 4 Memory Table 4-3. High-Page Register Summary (Sheet 2 of 3) Address 0x1810 0x1811 0x1812 0x1813 0x1814 0x1815 0x1816 0x1817 0x1818 0x1819– 0x181F 0x1820 0x1821 0x1822 0x1823 0x1824 0x1825 0x1826 0x1827– 0x183F 0x1840 0x1841 0x1842 0x1843 0x1844 0x1845 0x1846 0x1847 0x1848 0x1849 0x184A 0x184B 0x184C 0x184D 0x184E 0x184F 0x1850 0x1851 0x1852 0x1853 0x1854 0x1855 0x1856 Register Name DBGCAH DBGCAL DBGCBH DBGCBL DBGFH DBGFL DBGC DBGT DBGS Reserved FCDIV FOPT Reserved FCNFG FPROT FSTAT FCMD Reserved PTAPE PTASE PTADS Reserved PTBPE PTBSE PTBDS Reserved PTCPE PTCSE PTCDS Reserved PTDPE PTDSE PTDDS Reserved PTEPE PTESE PTEDS Reserved PTFPE PTFSE PTFDS Bit 7 Bit 15 Bit 7 Bit 15 Bit 7 Bit 15 Bit 7 DBGEN TRGSEL AF — DIVLD KEYEN — 0 FPS7 FCBEF FCMD7 — — — — — PTBPE7 PTBSE7 PTBDS7 — — — — — PTDPE7 PTDSE7 PTDDS7 — PTEPE7 PTESE7 PTEDS7 — PTFPE7 PTFSE7 PTFDS7 6 14 6 14 6 14 6 ARM BEGIN BF — PRDIV8 FNORED — 0 FPS6 FCCF FCMD6 — — — — — PTBPE6 PTBSE6 PTBDS6 — PTCPE6 PTCSE6 PTCDS6 — PTDPE6 PTDSE6 PTDDS6 — PTEPE6 PTESE6 PTEDS6 — PTFPE6 PTFSE6 PTFDS6 5 13 5 13 5 13 5 TAG 0 ARMF — DIV5 0 — KEYACC FPS5 FPVIOL FCMD5 — PTAPE5 PTASE5 PTADS5 — PTBPE5 PTBSE5 PTBDS5 — PTCPE5 PTCSE5 PTCDS5 — PTDPE5 PTDSE5 PTDDS5 — PTEPE5 PTESE5 PTEDS5 — PTFPE5 PTFSE5 PTFDS5 4 12 4 12 4 12 4 BRKEN 0 0 — DIV4 0 — 0 FPS4 FACCERR FCMD4 — PTAPE4 PTASE4 PTADS4 — PTBPE4 PTBSE4 PTBDS4 — PTCPE4 PTCSE4 PTCDS4 — PTDPE4 PTDSE4 PTDDS4 — PTEPE4 PTESE4 PTEDS4 — PTFPE4 PTFSE4 PTFDS4 3 11 3 11 3 11 3 RWA TRG3 CNT3 — DIV3 0 — 0 FPS3 0 FCMD3 — PTAPE3 PTASE3 PTADS3 — PTBPE3 PTBSE3 PTBDS3 — PTCPE3 PTCSE3 PTCDS3 — PTDPE3 PTDSE3 PTDDS3 — PTEPE3 PTESE3 PTEDS3 — PTFPE3 PTFSE3 PTFDS3 2 10 2 10 2 10 2 RWAEN TRG2 CNT2 — DIV2 0 — 0 FPS2 FBLANK FCMD2 — PTAPE2 PTASE2 PTADS2 — PTBPE2 PTBSE2 PTBDS2 — PTCPE2 PTCSE2 PTCDS2 — PTDPE2 PTDSE2 PTDDS2 — PTEPE2 PTESE2 PTEDS2 — PTFPE2 PTFSE2 PTFDS2 1 9 1 9 1 9 1 RWB TRG1 CNT1 — DIV1 SEC01 — 0 FPS1 0 FCMD1 — PTAPE1 PTASE1 PTADS1 — PTBPE1 PTBSE1 PTBDS1 — PTCPE1 PTCSE1 PTCDS1 — PTDPE1 PTDSE1 PTDDS1 — PTEPE1 PTESE1 PTEDS1 — PTFPE1 PTFSE1 PTFDS1 Bit 0 Bit 8 Bit 0 Bit 8 Bit 0 Bit 8 Bit 0 RWBEN TRG0 CNT0 — DIV0 SEC00 — 0 FPDIS 0 FCMD0 — PTAPE0 PTASE0 PTADS0 — PTBPE0 PTBSE0 PTBDS0 — PTCPE0 PTCSE0 PTCDS0 — PTDPE0 PTDSE0 PTDDS0 — PTEPE0 PTESE0 PTEDS0 — PTFPE0 PTFSE0 PTFDS0 MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 49 Chapter 4 Memory Table 4-3. High-Page Register Summary (Sheet 3 of 3) Address 0x1857 0x1858 0x1859 0x185A 0x185B– 0x185F 1 Register Name Reserved PTGPE PTGSE PTGDS Reserved Bit 7 — — — — — 6 — — — — — 5 — PTGPE5 PTGSE5 PTGDS5 — 4 — PTGPE4 PTGSE4 PTGDS4 — 3 — PTGPE3 PTGSE3 PTGDS3 — 2 — PTGPE2 PTGSE2 PTGDS2 — 1 — PTGPE1 PTGSE1 PTGDS1 — Bit 0 — PTGPE0 PTGSE0 PTGDS0 — This reserved bit must always be written to 0. Nonvolatile flash registers, shown in Table 4-4, are located in the flash memory. These registers include an 8-byte backdoor key which optionally can be used to gain access to secure memory resources. During reset events, the contents of NVPROT and NVOPT in the nonvolatile register area of the flash memory are transferred into corresponding FPROT and FOPT working registers in the high-page registers to control security and block protection options. Table 4-4. Nonvolatile Register Summary Address 0xFFAE 0xFFAF Register Name Reserved for storage of FTRIM Res. for storage of MCGTRIM Bit 7 0 6 0 5 0 4 0 TRIM 8-Byte Comparison Key — FPS7 — KEYEN — FPS6 — FNORED — FPS5 — 0 — FPS4 — 0 — FPS3 — 0 — FPS2 — 0 — FPS1 — SEC01 — FPDIS — SEC00 3 0 2 0 1 0 Bit 0 FTRIM 0xFFB0– NVBACKKEY 0xFFB7 0xFFB8– Reserved 0xFFBC 0xFFBD 0xFFBE 0xFFBF NVPROT Reserved NVOPT Provided the key enable (KEYEN) bit is 1, the 8-byte comparison key can be used to temporarily disengage memory security. This key mechanism can be accessed only through user code running in secure memory. (A security key cannot be entered directly through background debug commands.) This security key can be disabled completely by programming the KEYEN bit to 0. If the security key is disabled, the only way to disengage security is by mass erasing the flash if needed (normally through the background debug interface) and verifying that flash is blank. To avoid returning to secure mode after the next reset, program the security bits (SEC01:SEC00) to the unsecured state (1:0). 4.3 RAM (System RAM) The MC9S08JM60 series includes static RAM. The locations in RAM below 0x0100 can be accessed using the more efficient direct addressing mode, and any single bit in this area can be accessed with the bit manipulation instructions (BCLR, BSET, BRCLR, and BRSET). Locating the most frequently accessed program variables in this area of RAM is preferred. MC9S08JM60 Series Data Sheet, Rev. 3 50 Freescale Semiconductor Chapter 4 Memory The RAM retains data when the MCU is in low-power wait, stop2, or stop3 mode. At power-on, the contents of RAM are uninitialized. RAM data is unaffected by any reset provided that the supply voltage does not drop below the minimum value for RAM retention. For compatibility with older M68HC05 MCUs, the HCS08 resets the stack pointer to 0x00FF. In the MC9S08JM60 series, it is usually best to re-initialize the stack pointer to the top of the RAM so the direct page RAM can be used for frequently accessed RAM variables and bit-addressable program variables. Include the following 2-instruction sequence in your reset initialization routine (where RamLast is equated to the highest address of the RAM in the Freescale-provided equate file). LDHX TXS #RamLast+1 ;point one past RAM ;SP fADCK Subsequent continuous 10-bit or 12-bit; fBUS > fADCK Subsequent continuous 8-bit; fBUS > fADCK/11 Subsequent continuous 10-bit or 12-bit; fBUS > fADCK/11 ADICLK 0x, 10 0x, 10 0x, 10 0x, 10 11 11 11 11 xx xx xx xx ADLSMP 0 0 1 1 0 0 1 1 0 0 1 1 Max Total Conversion Time 20 ADCK cycles + 5 bus clock cycles 23 ADCK cycles + 5 bus clock cycles 40 ADCK cycles + 5 bus clock cycles 43 ADCK cycles + 5 bus clock cycles 5 μs + 20 ADCK + 5 bus clock cycles 5 μs + 23 ADCK + 5 bus clock cycles 5 μs + 40 ADCK + 5 bus clock cycles 5 μs + 43 ADCK + 5 bus clock cycles 17 ADCK cycles 20 ADCK cycles 37 ADCK cycles 40 ADCK cycles MC9S08JM60 Series Data Sheet, Rev. 3 152 Freescale Semiconductor Analog-to-Digital Converter (S08ADC12V1) The maximum total conversion time is determined by the clock source chosen and the divide ratio selected. The clock source is selectable by the ADICLK bits, and the divide ratio is specified by the ADIV bits. For example, in 10-bit mode, with the bus clock selected as the input clock source, the input clock divide-by-1 ratio selected, and a bus frequency of 8 MHz, then the conversion time for a single conversion is: Conversion time = 23 ADCK Cyc 8 MHz/1 + 5 bus Cyc 8 MHz = 3.5 μs Number of bus cycles = 3.5 μs x 8 MHz = 28 cycles NOTE The ADCK frequency must be between fADCK minimum and fADCK maximum to meet ADC specifications. 10.4.5 Automatic Compare Function The compare function can be configured to check for an upper or lower limit. After the input is sampled and converted, the result is added to the two’s complement of the compare value (ADCCVH and ADCCVL). When comparing to an upper limit (ACFGT = 1), if the result is greater-than or equal-to the compare value, COCO is set. When comparing to a lower limit (ACFGT = 0), if the result is less than the compare value, COCO is set. The value generated by the addition of the conversion result and the two’s complement of the compare value is transferred to ADCRH and ADCRL. Upon completion of a conversion while the compare function is enabled, if the compare condition is not true, COCO is not set and no data is transferred to the result registers. An ADC interrupt is generated upon the setting of COCO if the ADC interrupt is enabled (AIEN = 1). NOTE The compare function can monitor the voltage on a channel while the MCU is in wait or stop3 mode. The ADC interrupt wakes the MCU when the compare condition is met. 10.4.6 MCU Wait Mode Operation Wait mode is a lower power-consumption standby mode from which recovery is fast because the clock sources remain active. If a conversion is in progress when the MCU enters wait mode, it continues until completion. Conversions can be initiated while the MCU is in wait mode by means of the hardware trigger or if continuous conversions are enabled. The bus clock, bus clock divided by two, and ADACK are available as conversion clock sources while in wait mode. The use of ALTCLK as the conversion clock source in wait is dependent on the definition of ALTCLK for this MCU. Consult the module introduction for information on ALTCLK specific to this MCU. A conversion complete event sets the COCO and generates an ADC interrupt to wake the MCU from wait mode if the ADC interrupt is enabled (AIEN = 1). MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 153 Analog-to-Digital Converter (S08ADC12V1) 10.4.7 MCU Stop3 Mode Operation Stop mode is a low power-consumption standby mode during which most or all clock sources on the MCU are disabled. 10.4.7.1 Stop3 Mode With ADACK Disabled If the asynchronous clock, ADACK, is not selected as the conversion clock, executing a stop instruction aborts the current conversion and places the ADC in its idle state. The contents of ADCRH and ADCRL are unaffected by stop3 mode. After exiting from stop3 mode, a software or hardware trigger is required to resume conversions. 10.4.7.2 Stop3 Mode With ADACK Enabled If ADACK is selected as the conversion clock, the ADC continues operation during stop3 mode. For guaranteed ADC operation, the MCU’s voltage regulator must remain active during stop3 mode. Consult the module introduction for configuration information for this MCU. If a conversion is in progress when the MCU enters stop3 mode, it continues until completion. Conversions can be initiated while the MCU is in stop3 mode by means of the hardware trigger or if continuous conversions are enabled. A conversion complete event sets the COCO and generates an ADC interrupt to wake the MCU from stop3 mode if the ADC interrupt is enabled (AIEN = 1). NOTE The ADC module can wake the system from low-power stop and cause the MCU to begin consuming run-level currents without generating a system level interrupt. To prevent this scenario, software should ensure the data transfer blocking mechanism (discussed in Section 10.4.4.2, “Completing Conversions,”) is cleared when entering stop3 and continuing ADC conversions. 10.4.8 MCU Stop2 Mode Operation The ADC module is automatically disabled when the MCU enters stop2 mode. All module registers contain their reset values following exit from stop2. Therefore, the module must be re-enabled and re-configured following exit from stop2. 10.5 Initialization Information This section gives an example that provides some basic direction on how to initialize and configure the ADC module. You can configure the module for 8-, 10-, or 12-bit resolution, single or continuous conversion, and a polled or interrupt approach, among many other options. Refer to Table 10-7, Table 10-8, and Table 10-9 for information used in this example. MC9S08JM60 Series Data Sheet, Rev. 3 154 Freescale Semiconductor Analog-to-Digital Converter (S08ADC12V1) NOTE Hexadecimal values designated by a preceding 0x, binary values designated by a preceding %, and decimal values have no preceding character. 10.5.1 10.5.1.1 ADC Module Initialization Example Initialization Sequence Before the ADC module can be used to complete conversions, an initialization procedure must be performed. A typical sequence is as follows: 1. Update the configuration register (ADCCFG) to select the input clock source and the divide ratio used to generate the internal clock, ADCK. This register is also used for selecting sample time and low-power configuration. 2. Update status and control register 2 (ADCSC2) to select the conversion trigger (hardware or software) and compare function options, if enabled. 3. Update status and control register 1 (ADCSC1) to select whether conversions will be continuous or completed only once, and to enable or disable conversion complete interrupts. The input channel on which conversions will be performed is also selected here. 10.5.1.2 Pseudo-Code Example In this example, the ADC module is set up with interrupts enabled to perform a single 10-bit conversion at low power with a long sample time on input channel 1, where the internal ADCK clock is derived from the bus clock divided by 1. ADCCFG = 0x98 (%10011000) Bit Bit Bit Bit Bit 7 6:5 4 3:2 1:0 ADLPC ADIV ADLSMP MODE ADICLK 1 00 1 10 00 Configures for low power (lowers maximum clock speed) Sets the ADCK to the input clock ÷ 1 Configures for long sample time Sets mode at 10-bit conversions Selects bus clock as input clock source ADCSC2 = 0x00 (%00000000) Bit Bit Bit Bit Bit Bit 7 6 5 4 3:2 1:0 ADACT ADTRG ACFE ACFGT 0 0 0 0 00 00 Flag indicates if a conversion is in progress Software trigger selected Compare function disabled Not used in this example Reserved, always reads zero Reserved for Freescale’s internal use; always write zero ADCSC1 = 0x41 (%01000001) Bit Bit Bit Bit 7 6 5 4:0 COCO AIEN ADCO ADCH 0 1 0 00001 Read-only flag which is set when a conversion completes Conversion complete interrupt enabled One conversion only (continuous conversions disabled) Input channel 1 selected as ADC input channel ADCRH/L = 0xxx Holds results of conversion. Read high byte (ADCRH) before low byte (ADCRL) so that conversion data cannot be overwritten with data from the next conversion. MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 155 Analog-to-Digital Converter (S08ADC12V1) ADCCVH/L = 0xxx Holds compare value when compare function enabled APCTL1=0x02 AD1 pin I/O control disabled. All other AD pins remain general purpose I/O pins APCTL2=0x00 All other AD pins remain general purpose I/O pins Reset Initialize ADC ADCCFG = 0x98 ADCSC2 = 0x00 ADCSC1 = 0x41 Check COCO=1? Yes Read ADCRH Then ADCRL To Clear COCO Bit No Continue Figure 10-13. Initialization Flowchart for Example 10.6 Application Information This section contains information for using the ADC module in applications. The ADC has been designed to be integrated into a microcontroller for use in embedded control applications requiring an A/D converter. 10.6.1 External Pins and Routing The following sections discuss the external pins associated with the ADC module and how they should be used for best results. MC9S08JM60 Series Data Sheet, Rev. 3 156 Freescale Semiconductor Analog-to-Digital Converter (S08ADC12V1) 10.6.1.1 Analog Supply Pins The ADC module has analog power and ground supplies (VDDAD and VSSAD) available as separate pins on some devices. VSSAD is shared on the same pin as the MCU digital VSS on some devices. On other devices, VSSAD and VDDAD are shared with the MCU digital supply pins. In these cases, there are separate pads for the analog supplies bonded to the same pin as the corresponding digital supply so that some degree of isolation between the supplies is maintained. When available on a separate pin, both VDDAD and VSSAD must be connected to the same voltage potential as their corresponding MCU digital supply (VDD and VSS) and must be routed carefully for maximum noise immunity and bypass capacitors placed as near as possible to the package. If separate power supplies are used for analog and digital power, the ground connection between these supplies must be at the VSSAD pin. This should be the only ground connection between these supplies if possible. The VSSAD pin makes a good single point ground location. 10.6.1.2 Analog Reference Pins In addition to the analog supplies, the ADC module has connections for two reference voltage inputs. The high reference is VREFH, which may be shared on the same pin as VDDAD on some devices. The low reference is VREFL, which may be shared on the same pin as VSSAD on some devices. When available on a separate pin, VREFH may be connected to the same potential as VDDAD, or may be driven by an external source between the minimum VDDAD spec and the VDDAD potential (VREFH must never exceed VDDAD). When available on a separate pin, VREFL must be connected to the same voltage potential as VSSAD. VREFH and VREFL must be routed carefully for maximum noise immunity and bypass capacitors placed as near as possible to the package. AC current in the form of current spikes required to supply charge to the capacitor array at each successive approximation step is drawn through the VREFH and VREFL loop. The best external component to meet this current demand is a 0.1 μF capacitor with good high frequency characteristics. This capacitor is connected between VREFH and VREFL and must be placed as near as possible to the package pins. Resistance in the path is not recommended because the current causes a voltage drop that could result in conversion errors. Inductance in this path must be minimum (parasitic only). 10.6.1.3 Analog Input Pins The external analog inputs are typically shared with digital I/O pins on MCU devices. The pin I/O control is disabled by setting the appropriate control bit in one of the pin control registers. Conversions can be performed on inputs without the associated pin control register bit set. It is recommended that the pin control register bit always be set when using a pin as an analog input. This avoids problems with contention because the output buffer is in its high impedance state and the pullup is disabled. Also, the input buffer draws DC current when its input is not at VDD or VSS. Setting the pin control register bits for all pins used as analog inputs should be done to achieve lowest operating current. Empirical data shows that capacitors on the analog inputs improve performance in the presence of noise or when the source impedance is high. Use of 0.01 μF capacitors with good high-frequency characteristics is sufficient. These capacitors are not necessary in all cases, but when used they must be placed as near as possible to the package pins and be referenced to VSSA. MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 157 Analog-to-Digital Converter (S08ADC12V1) For proper conversion, the input voltage must fall between VREFH and VREFL. If the input is equal to or exceeds VREFH, the converter circuit converts the signal to 0xFFF (full scale 12-bit representation), 0x3FF (full scale 10-bit representation) or 0xFF (full scale 8-bit representation). If the input is equal to or less than VREFL, the converter circuit converts it to 0x000. Input voltages between VREFH and VREFL are straight-line linear conversions. There is a brief current associated with VREFL when the sampling capacitor is charging. The input is sampled for 3.5 cycles of the ADCK source when ADLSMP is low, or 23.5 cycles when ADLSMP is high. For minimal loss of accuracy due to current injection, pins adjacent to the analog input pins should not be transitioning during conversions. 10.6.2 Sources of Error Several sources of error exist for A/D conversions. These are discussed in the following sections. 10.6.2.1 Sampling Error For proper conversions, the input must be sampled long enough to achieve the proper accuracy. Given the maximum input resistance of approximately 7kΩ and input capacitance of approximately 5.5 pF, sampling to within 1/4LSB (at 12-bit resolution) can be achieved within the minimum sample window (3.5 cycles @ 8 MHz maximum ADCK frequency) provided the resistance of the external analog source (RAS) is kept below 2 kΩ. Higher source resistances or higher-accuracy sampling is possible by setting ADLSMP (to increase the sample window to 23.5 cycles) or decreasing ADCK frequency to increase sample time. 10.6.2.2 Pin Leakage Error Leakage on the I/O pins can cause conversion error if the external analog source resistance (RAS) is high. If this error cannot be tolerated by the application, keep RAS lower than VDDAD / (2N*ILEAK) for less than 1/4LSB leakage error (N = 8 in 8-bit, 10 in 10-bit or 12 in 12-bit mode). 10.6.2.3 Noise-Induced Errors System noise that occurs during the sample or conversion process can affect the accuracy of the conversion. The ADC accuracy numbers are guaranteed as specified only if the following conditions are met: • There is a 0.1 μF low-ESR capacitor from VREFH to VREFL. • There is a 0.1 μF low-ESR capacitor from VDDAD to VSSAD. • If inductive isolation is used from the primary supply, an additional 1 μF capacitor is placed from VDDAD to VSSAD. • VSSAD (and VREFL, if connected) is connected to VSS at a quiet point in the ground plane. • Operate the MCU in wait or stop3 mode before initiating (hardware triggered conversions) or immediately after initiating (hardware or software triggered conversions) the ADC conversion. — For software triggered conversions, immediately follow the write to ADCSC1 with a wait instruction or stop instruction. MC9S08JM60 Series Data Sheet, Rev. 3 158 Freescale Semiconductor Analog-to-Digital Converter (S08ADC12V1) • — For stop3 mode operation, select ADACK as the clock source. Operation in stop3 reduces VDD noise but increases effective conversion time due to stop recovery. There is no I/O switching, input or output, on the MCU during the conversion. There are some situations where external system activity causes radiated or conducted noise emissions or excessive VDD noise is coupled into the ADC. In these situations, or when the MCU cannot be placed in wait or stop3 or I/O activity cannot be halted, these recommended actions may reduce the effect of noise on the accuracy: • Place a 0.01 μF capacitor (CAS) on the selected input channel to VREFL or VSSAD (this improves noise issues, but affects the sample rate based on the external analog source resistance). • Average the result by converting the analog input many times in succession and dividing the sum of the results. Four samples are required to eliminate the effect of a 1LSB, one-time error. • Reduce the effect of synchronous noise by operating off the asynchronous clock (ADACK) and averaging. Noise that is synchronous to ADCK cannot be averaged out. 10.6.2.4 Code Width and Quantization Error The ADC quantizes the ideal straight-line transfer function into 4096 steps (in 12-bit mode). Each step ideally has the same height (1 code) and width. The width is defined as the delta between the transition points to one code and the next. The ideal code width for an N bit converter (in this case N can be 8, 10 or 12), defined as 1LSB, is: 1 lsb = (VREFH - VREFL) / 2N Eqn. 10-2 There is an inherent quantization error due to the digitization of the result. For 8-bit or 10-bit conversions the code transitions when the voltage is at the midpoint between the points where the straight line transfer function is exactly represented by the actual transfer function. Therefore, the quantization error will be ± 1/2 lsb in 8- or 10-bit mode. As a consequence, however, the code width of the first (0x000) conversion is only 1/2 lsb and the code width of the last (0xFF or 0x3FF) is 1.5 lsb. For 12-bit conversions the code transitions only after the full code width is present, so the quantization error is −1 lsb to 0 lsb and the code width of each step is 1 lsb. 10.6.2.5 Linearity Errors The ADC may also exhibit non-linearity of several forms. Every effort has been made to reduce these errors but the system should be aware of them because they affect overall accuracy. These errors are: • Zero-scale error (EZS) (sometimes called offset) — This error is defined as the difference between the actual code width of the first conversion and the ideal code width (1/2 lsb in 8-bit or 10-bit modes and 1 lsb in 12-bit mode). If the first conversion is 0x001, the difference between the actual 0x001 code width and its ideal (1 lsb) is used. • Full-scale error (EFS) — This error is defined as the difference between the actual code width of the last conversion and the ideal code width (1.5 lsb in 8-bit or 10-bit modes and 1LSB in 12-bit mode). If the last conversion is 0x3FE, the difference between the actual 0x3FE code width and its ideal (1LSB) is used. MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 159 Analog-to-Digital Converter (S08ADC12V1) • • • Differential non-linearity (DNL) — This error is defined as the worst-case difference between the actual code width and the ideal code width for all conversions. Integral non-linearity (INL) — This error is defined as the highest-value the (absolute value of the) running sum of DNL achieves. More simply, this is the worst-case difference of the actual transition voltage to a given code and its corresponding ideal transition voltage, for all codes. Total unadjusted error (TUE) — This error is defined as the difference between the actual transfer function and the ideal straight-line transfer function and includes all forms of error. 10.6.2.6 Code Jitter, Non-Monotonicity, and Missing Codes Analog-to-digital converters are susceptible to three special forms of error. These are code jitter, non-monotonicity, and missing codes. Code jitter is when, at certain points, a given input voltage converts to one of two values when sampled repeatedly. Ideally, when the input voltage is infinitesimally smaller than the transition voltage, the converter yields the lower code (and vice-versa). However, even small amounts of system noise can cause the converter to be indeterminate (between two codes) for a range of input voltages around the transition voltage. This range is normally around ±1/2 lsb in 8-bit or 10-bit mode, or around 2 lsb in 12-bit mode, and increases with noise. This error may be reduced by repeatedly sampling the input and averaging the result. Additionally the techniques discussed in Section 10.6.2.3 reduces this error. Non-monotonicity is defined as when, except for code jitter, the converter converts to a lower code for a higher input voltage. Missing codes are those values never converted for any input value. In 8-bit or 10-bit mode, the ADC is guaranteed to be monotonic and have no missing codes. MC9S08JM60 Series Data Sheet, Rev. 3 160 Freescale Semiconductor Chapter 11 Inter-Integrated Circuit (S08IICV2) 11.1 Introduction The MC9S08JM60 series of microcontrollers has an inter-integrated circuit (IIC) module for communication with other integrated circuits. The two pins associated with this module, SCL and SDA, are shared with PTC0 and PTC1, respectively. NOTE MC9S08JM60 series devices operate at a higher voltage range (2.7 V to 5.5 V) and do not include stop1 mode. Therefore, please disregard references to stop1. MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 161 Chapter 11 Inter-Integrated Circuit (S08IICV2) USBDP USBDN PORT A 6 PTA5– PTA0 PTB7/ADP7 PTB6/ADP6 PTB5/KBIP5/ADP5 PTB4/KBIP4/ADP4 PTB3/SS2/ADP3 PTB2/SPSCK2/ADP2 PTB1/MOSI2/ADP1 PTB0/MISO2/ADP0 PTC6 PTC5/RxD2 PTC4 PTC3/TxD2 PTC2 PTC1/SDA PTC0/SCL PTD7 PTD6 PTD5 PTD4/ADP11 PTD3/KBIP3/ADP10 PTD2/KBIP2/ACMPO PTD1/ADP9/ACMP– PTD0/ADP8/ACMP+ PTE7/SS1 PTE6/SPSCK1 PTE5/MOSI1 PTE4/MISO1 PORT E PTE3/TPM1CH1 PTE2/TPM1CH0 PTE1/RxD1 PTE0/TxD1 PTF7 PTF6 PTF5/TPM2CH1 PTF4/TPM2CH0 PTF3/TPM1CH5 PTF2/TPM1CH4 PTF1/TPM1CH3 PTF0/TPM1CH2 PTG5/EXTAL PTG4/XTAL PTG3/KBIP7 PTG2/KBIP6 PTG1/KBIP1 PTG0/KBIP0 PORT G HCS08 CORE ON-CHIP ICE AND DEBUG MODULE (DBG) FULL SPEED USB USB ENDPOINT TRANSCEIVER RAM 8-/16-BIT SERIAL PERIPHERAL INTERFACE MODULE (SPI2) SS2 SPSCK2 MOSI2 MISO2 RxD2 TxD2 SDA SCL USB SIE BKGD/MS BDC CPU RESET HCS08 SYSTEM CONTROL RESETS AND INTERRUPTS MODES OF OPERATION POWER MANAGEMENT IRQ/TPMCLK SERIAL COMMUNICATIONS INTERFACE MODULE (SCI2) COP IRQ LVD IIC MODULE (IIC) VDDAD VSSAD VREFL VREFH USER Flash (IN BYTES) MC9S08JM60 = 60,912 MC9S08JM32 = 32,768 12-CHANNEL, 12-BIT ANALOG-TO-DIGITAL CONVERTER (ADC) 8 4 PORT D ACMP– ANALOG COMPARATOR (ACMP) ACMP+ ACMPO SS1 SPSCK1 MOSI1 MISO1 TPMCLK TPM1CH1 TPM1CH0 TPM1CHx 4 RxD1 TxD1 TPMCLK TPM2CH1 TPM2CH0 KBIPx USER RAM (IN BYTES) MC9S08JM60 = 4096 MC9S08JM32 = 2048 8-/16-BIT SERIAL PERIPHERAL INTERFACE MODULE (SPI1) MULTI-PURPOSE CLOCK GENERATOR (MCG) VSSOSC 6-CHANNEL TIMER/PWM MODULE (TPM1) SERIAL COMMUNICATIONS INTERFACE MODULE (SCI1) LOW-POWER OSCILLATOR SYSTEM VOLTAGE REGULATOR USB 3.3-V VOLTAGE REGULATOR REAL-TIME COUNTER (RTC) VDD VSS MODULE (TPM2) VUSB33 4 4 8-BIT KEYBOARD INTERRUPT MODULE (KBI) KBIPx EXTAL XTAL NOTES: 1. Port pins are software configurable with pullup device if input port. 2. Pin contains software configurable pullup/pull-down device if IRQ is enabled (IRQPE = 1). Pull-down is enabled if rising edge detect is selected (IRQEDG = 1) 3. IRQ does not have a clamp diode to VDD. IRQ must not be driven above VDD. 4. Pin contains integrated pullup device. 5. When pin functions as KBI (KBIPEn = 1) and associated pin is configured to enable the pullup device, KBEDGn can be used to reconfigure the pull-up as a pull-down device. Figure 11-1. MC9S08JM60 Series Block Diagram Highlighting the IIC Block and Pins MC9S08JM60 Series Data Sheet, Rev. 3 162 Freescale Semiconductor PORT F 2-CHANNEL TIMER/PWM PORT C PORT B 11.1.1 Features The IIC includes these distinctive features: • Compatible with IIC bus standard • Multi-master operation • Software programmable for one of 64 different serial clock frequencies • Software selectable acknowledge bit • Interrupt driven byte-by-byte data transfer • Arbitration lost interrupt with automatic mode switching from master to slave • Calling address identification interrupt • Start and stop signal generation/detection • Repeated start signal generation • Acknowledge bit generation/detection • Bus busy detection • General call recognition • 10-bit address extension 11.1.2 Modes of Operation A brief description of the IIC in the various MCU modes is given here. • Run mode — This is the basic mode of operation. To conserve power in this mode, disable the module. • Wait mode — The module continues to operate while the MCU is in wait mode and can provide a wake-up interrupt. • Stop mode — The IIC is inactive in stop3 mode for reduced power consumption. The stop instruction does not affect IIC register states. Stop2 resets the register contents. 11.1.3 Block Diagram Figure 11-2 is a block diagram of the IIC. MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 163 Address Interrupt ADDR_DECODE Data Bus DATA_MUX CTRL_REG FREQ_REG ADDR_REG STATUS_REG DATA_REG Input Sync Start Stop Arbitration Control Clock Control In/Out Data Shift Register Address Compare SCL SDA Figure 11-2. IIC Functional Block Diagram 11.2 External Signal Description This section describes each user-accessible pin signal. 11.2.1 SCL — Serial Clock Line The bidirectional SCL is the serial clock line of the IIC system. 11.2.2 SDA — Serial Data Line The bidirectional SDA is the serial data line of the IIC system. 11.3 Register Definition This section consists of the IIC register descriptions in address order. Refer to the direct-page register summary in the memory chapter of this document for the absolute address assignments for all IIC registers. This section refers to registers and control bits only by their names. A MC9S08JM60 Series Data Sheet, Rev. 3 164 Freescale Semiconductor Freescale-provided equate or header file is used to translate these names into the appropriate absolute addresses. 11.3.1 IIC Address Register (IICA) 7 6 5 4 3 2 1 0 R AD7 W Reset 0 0 0 0 0 0 0 AD6 AD5 AD4 AD3 AD2 AD1 0 0 = Unimplemented or Reserved Figure 11-3. IIC Address Register (IICA) Table 11-1. IICA Field Descriptions Field 7–1 AD[7:1] Description Slave Address. The AD[7:1] field contains the slave address to be used by the IIC module. This field is used on the 7-bit address scheme and the lower seven bits of the 10-bit address scheme. 11.3.2 IIC Frequency Divider Register (IICF) 7 6 5 4 3 2 1 0 R MULT W Reset 0 0 0 0 0 0 0 0 ICR Figure 11-4. IIC Frequency Divider Register (IICF) MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 165 Table 11-2. IICF Field Descriptions Field 7–6 MULT Description IIC Multiplier Factor. The MULT bits define the multiplier factor, mul. This factor, along with the SCL divider, generates the IIC baud rate. The multiplier factor mul as defined by the MULT bits is provided below. 00 mul = 01 01 mul = 02 10 mul = 04 11 Reserved IIC Clock Rate. The ICR bits are used to prescale the bus clock for bit rate selection. These bits and the MULT bits determine the IIC baud rate, the SDA hold time, the SCL Start hold time, and the SCL Stop hold time. Table 11-4 provides the SCL divider and hold values for corresponding values of the ICR. The SCL divider multiplied by multiplier factor mul generates IIC baud rate. bus speed (Hz) IIC baud rate = -------------------------------------------mul × SCLdivider 5–0 ICR Eqn. 11-1 SDA hold time is the delay from the falling edge of SCL (IIC clock) to the changing of SDA (IIC data). SDA hold time = bus period (s) × mul × SDA hold value Eqn. 11-2 SCL start hold time is the delay from the falling edge of SDA (IIC data) while SCL is high (Start condition) to the falling edge of SCL (IIC clock). SCL Start hold time = bus period (s) × mul × SCL Start hold value SCL stop hold time is the delay from the rising edge of SCL (IIC clock) to the rising edge of SDA SDA (IIC data) while SCL is high (Stop condition). SCL Stop hold time = bus period (s) × mul × SCL Stop hold value Eqn. 11-3 Eqn. 11-4 For example, if the bus speed is 8 MHz, the table below shows the possible hold time values with different ICR and MULT selections to achieve an IIC baud rate of 100kbps. Table 11-3. Hold Time Values for 8 MHz Bus Speed Hold Times (μs) MULT ICR SDA 0x2 0x1 0x1 0x0 0x0 0x00 0x07 0x0B 0x14 0x18 3.500 2.500 2.250 2.125 1.125 SCL Start 3.000 4.000 4.000 4.250 4.750 SCL Stop 5.500 5.250 5.250 5.125 5.125 MC9S08JM60 Series Data Sheet, Rev. 3 166 Freescale Semiconductor Table 11-4. IIC Divider and Hold Values ICR (hex) 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F SCL Divider 20 22 24 26 28 30 34 40 28 32 36 40 44 48 56 68 48 56 64 72 80 88 104 128 80 96 112 128 144 160 192 240 SDA Hold Value 7 7 8 8 9 9 10 10 7 7 9 9 11 11 13 13 9 9 13 13 17 17 21 21 9 9 17 17 25 25 33 33 SCL Hold (Start) Value 6 7 8 9 10 11 13 16 10 12 14 16 18 20 24 30 18 22 26 30 34 38 46 58 38 46 54 62 70 78 94 118 SCL Hold (Stop) Value 11 12 13 14 15 16 18 21 15 17 19 21 23 25 29 35 25 29 33 37 41 45 53 65 41 49 57 65 73 81 97 121 ICR (hex) 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F SCL Divider 160 192 224 256 288 320 384 480 320 384 448 512 576 640 768 960 640 768 896 1024 1152 1280 1536 1920 1280 1536 1792 2048 2304 2560 3072 3840 SDA Hold Value 17 17 33 33 49 49 65 65 33 33 65 65 97 97 129 129 65 65 129 129 193 193 257 257 129 129 257 257 385 385 513 513 SCL Hold (Start) Value 78 94 110 126 142 158 190 238 158 190 222 254 286 318 382 478 318 382 446 510 574 638 766 958 638 766 894 1022 1150 1278 1534 1918 SCL Hold (Stop) Value 81 97 113 129 145 161 193 241 161 193 225 257 289 321 385 481 321 385 449 513 577 641 769 961 641 769 897 1025 1153 1281 1537 1921 MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 167 11.3.3 IIC Control Register (IICC1) 7 6 5 4 3 2 1 0 R IICEN W Reset 0 0 0 0 0 IICIE MST TX TXAK 0 RSTA 0 0 0 0 0 = Unimplemented or Reserved Figure 11-5. IIC Control Register (IICC1) Table 11-5. IICC1 Field Descriptions Field 7 IICEN 6 IICIE 5 MST Description IIC Enable. The IICEN bit determines whether the IIC module is enabled. 0 IIC is not enabled 1 IIC is enabled IIC Interrupt Enable. The IICIE bit determines whether an IIC interrupt is requested. 0 IIC interrupt request not enabled 1 IIC interrupt request enabled Master Mode Select. The MST bit changes from a 0 to a 1 when a start signal is generated on the bus and master mode is selected. When this bit changes from a 1 to a 0 a stop signal is generated and the mode of operation changes from master to slave. 0 Slave mode 1 Master mode Transmit Mode Select. The TX bit selects the direction of master and slave transfers. In master mode, this bit should be set according to the type of transfer required. Therefore, for address cycles, this bit is always high. When addressed as a slave, this bit should be set by software according to the SRW bit in the status register. 0 Receive 1 Transmit Transmit Acknowledge Enable. This bit specifies the value driven onto the SDA during data acknowledge cycles for master and slave receivers. 0 An acknowledge signal is sent out to the bus after receiving one data byte 1 No acknowledge signal response is sent Repeat start. Writing a 1 to this bit generates a repeated start condition provided it is the current master. This bit is always read as cleared. Attempting a repeat at the wrong time results in loss of arbitration. 4 TX 3 TXAK 2 RSTA 11.3.4 IIC Status Register (IICS) 7 6 5 4 3 2 1 0 R W Reset TCF IAAS 1 0 BUSY ARBL 0 0 0 SRW IICIF RXAK 0 0 0 0 = Unimplemented or Reserved Figure 11-6. IIC Status Register (IICS) MC9S08JM60 Series Data Sheet, Rev. 3 168 Freescale Semiconductor Table 11-6. IICS Field Descriptions Field 7 TCF Description Transfer Complete Flag. This bit is set on the completion of a byte transfer. This bit is only valid during or immediately following a transfer to the IIC module or from the IIC module.The TCF bit is cleared by reading the IICD register in receive mode or writing to the IICD in transmit mode. 0 Transfer in progress 1 Transfer complete Addressed as a Slave. The IAAS bit is set when the calling address matches the programmed slave address or when the GCAEN bit is set and a general call is received. Writing the IICC register clears this bit. 0 Not addressed 1 Addressed as a slave Bus Busy. The BUSY bit indicates the status of the bus regardless of slave or master mode. The BUSY bit is set when a start signal is detected and cleared when a stop signal is detected. 0 Bus is idle 1 Bus is busy Arbitration Lost. This bit is set by hardware when the arbitration procedure is lost. The ARBL bit must be cleared by software by writing a 1 to it. 0 Standard bus operation 1 Loss of arbitration Slave Read/Write. When addressed as a slave, the SRW bit indicates the value of the R/W command bit of the calling address sent to the master. 0 Slave receive, master writing to slave 1 Slave transmit, master reading from slave IIC Interrupt Flag. The IICIF bit is set when an interrupt is pending. This bit must be cleared by software, by writing a 1 to it in the interrupt routine. One of the following events can set the IICIF bit: • One byte transfer completes • Match of slave address to calling address • Arbitration lost 0 No interrupt pending 1 Interrupt pending Receive Acknowledge. When the RXAK bit is low, it indicates an acknowledge signal has been received after the completion of one byte of data transmission on the bus. If the RXAK bit is high it means that no acknowledge signal is detected. 0 Acknowledge received 1 No acknowledge received 6 IAAS 5 BUSY 4 ARBL 2 SRW 1 IICIF 0 RXAK 11.3.5 IIC Data I/O Register (IICD) 7 6 5 4 3 2 1 0 R DATA W Reset 0 0 0 0 0 0 0 0 Figure 11-7. IIC Data I/O Register (IICD) MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 169 Table 11-7. IICD Field Descriptions Field 7–0 DATA Description Data — In master transmit mode, when data is written to the IICD, a data transfer is initiated. The most significant bit is sent first. In master receive mode, reading this register initiates receiving of the next byte of data. NOTE When transitioning out of master receive mode, the IIC mode should be switched before reading the IICD register to prevent an inadvertent initiation of a master receive data transfer. In slave mode, the same functions are available after an address match has occurred. The TX bit in IICC must correctly reflect the desired direction of transfer in master and slave modes for the transmission to begin. For instance, if the IIC is configured for master transmit but a master receive is desired, reading the IICD does not initiate the receive. Reading the IICD returns the last byte received while the IIC is configured in master receive or slave receive modes. The IICD does not reflect every byte transmitted on the IIC bus, nor can software verify that a byte has been written to the IICD correctly by reading it back. In master transmit mode, the first byte of data written to IICD following assertion of MST is used for the address transfer and should comprise of the calling address (in bit 7 to bit 1) concatenated with the required R/W bit (in position bit 0). 11.3.6 IIC Control Register 2 (IICC2) 7 6 5 4 3 2 1 0 R GCAEN W Reset 0 0 ADEXT 0 0 0 AD10 AD9 0 AD8 0 0 0 0 0 = Unimplemented or Reserved Figure 11-8. IIC Control Register (IICC2) Table 11-8. IICC2 Field Descriptions Field 7 GCAEN 6 ADEXT 2–0 AD[10:8] Description General Call Address Enable. The GCAEN bit enables or disables general call address. 0 General call address is disabled 1 General call address is enabled Address Extension. The ADEXT bit controls the number of bits used for the slave address. 0 7-bit address scheme 1 10-bit address scheme Slave Address. The AD[10:8] field contains the upper three bits of the slave address in the 10-bit address scheme. This field is only valid when the ADEXT bit is set. MC9S08JM60 Series Data Sheet, Rev. 3 170 Freescale Semiconductor 11.4 Functional Description This section provides a complete functional description of the IIC module. 11.4.1 IIC Protocol The IIC bus system uses a serial data line (SDA) and a serial clock line (SCL) for data transfer. All devices connected to it must have open drain or open collector outputs. A logic AND function is exercised on both lines with external pull-up resistors. The value of these resistors is system dependent. Normally, a standard communication is composed of four parts: • Start signal • Slave address transmission • Data transfer • Stop signal The stop signal should not be confused with the CPU stop instruction. The IIC bus system communication is described briefly in the following sections and illustrated in Figure 11-9. msb SCL 1 2 3 4 5 6 7 lsb 8 9 msb 1 2 3 4 5 6 7 lsb 8 9 SDA AD7 AD6 AD5 AD4 AD3 AD2 AD1 R/W XXX D7 D6 D5 D4 D3 D2 D1 D0 Start Signal Calling Address Read/ Ack Write Bit Data Byte No Ack Bit lsb Stop Signal msb SCL 1 2 3 4 5 6 7 lsb 8 9 msb 1 2 3 4 5 6 7 8 9 SDA AD7 AD6 AD5 AD4 AD3 AD2 AD1 R/W XX AD7 AD6 AD5 AD4 AD3 AD2 AD1 R/W Start Signal Calling Address Read/ Ack Write Bit Repeated Start Signal New Calling Address Read/ Write No Ack Bit Stop Signal Figure 11-9. IIC Bus Transmission Signals 11.4.1.1 Start Signal When the bus is free, no master device is engaging the bus (SCL and SDA lines are at logical high), a master may initiate communication by sending a start signal. As shown in Figure 11-9, a start signal is defined as a high-to-low transition of SDA while SCL is high. This signal denotes the beginning of a new data transfer (each data transfer may contain several bytes of data) and brings all slaves out of their idle states. MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 171 11.4.1.2 Slave Address Transmission The first byte of data transferred immediately after the start signal is the slave address transmitted by the master. This is a seven-bit calling address followed by a R/W bit. The R/W bit tells the slave the desired direction of data transfer. 1 = Read transfer, the slave transmits data to the master. 0 = Write transfer, the master transmits data to the slave. Only the slave with a calling address that matches the one transmitted by the master responds by sending back an acknowledge bit. This is done by pulling the SDA low at the ninth clock (see Figure 11-9). No two slaves in the system may have the same address. If the IIC module is the master, it must not transmit an address equal to its own slave address. The IIC cannot be master and slave at the same time. However, if arbitration is lost during an address cycle, the IIC reverts to slave mode and operates correctly even if it is being addressed by another master. 11.4.1.3 Data Transfer Before successful slave addressing is achieved, the data transfer can proceed byte-by-byte in a direction specified by the R/W bit sent by the calling master. All transfers that come after an address cycle are referred to as data transfers, even if they carry sub-address information for the slave device Each data byte is 8 bits long. Data may be changed only while SCL is low and must be held stable while SCL is high as shown in Figure 11-9. There is one clock pulse on SCL for each data bit, the msb being transferred first. Each data byte is followed by a 9th (acknowledge) bit, which is signalled from the receiving device. An acknowledge is signalled by pulling the SDA low at the ninth clock. In summary, one complete data transfer needs nine clock pulses. If the slave receiver does not acknowledge the master in the ninth bit time, the SDA line must be left high by the slave. The master interprets the failed acknowledge as an unsuccessful data transfer. If the master receiver does not acknowledge the slave transmitter after a data byte transmission, the slave interprets this as an end of data transfer and releases the SDA line. In either case, the data transfer is aborted and the master does one of two things: • Relinquishes the bus by generating a stop signal. • Commences a new calling by generating a repeated start signal. 11.4.1.4 Stop Signal The master can terminate the communication by generating a stop signal to free the bus. However, the master may generate a start signal followed by a calling command without generating a stop signal first. This is called repeated start. A stop signal is defined as a low-to-high transition of SDA while SCL at logical 1 (see Figure 11-9). The master can generate a stop even if the slave has generated an acknowledge at which point the slave must release the bus. MC9S08JM60 Series Data Sheet, Rev. 3 172 Freescale Semiconductor 11.4.1.5 Repeated Start Signal As shown in Figure 11-9, a repeated start signal is a start signal generated without first generating a stop signal to terminate the communication. This is used by the master to communicate with another slave or with the same slave in different mode (transmit/receive mode) without releasing the bus. 11.4.1.6 Arbitration Procedure The IIC bus is a true multi-master bus that allows more than one master to be connected on it. If two or more masters try to control the bus at the same time, a clock synchronization procedure determines the bus clock, for which the low period is equal to the longest clock low period and the high is equal to the shortest one among the masters. The relative priority of the contending masters is determined by a data arbitration procedure, a bus master loses arbitration if it transmits logic 1 while another master transmits logic 0. The losing masters immediately switch over to slave receive mode and stop driving SDA output. In this case, the transition from master to slave mode does not generate a stop condition. Meanwhile, a status bit is set by hardware to indicate loss of arbitration. 11.4.1.7 Clock Synchronization Because wire-AND logic is performed on the SCL line, a high-to-low transition on the SCL line affects all the devices connected on the bus. The devices start counting their low period and after a device’s clock has gone low, it holds the SCL line low until the clock high state is reached. However, the change of low to high in this device clock may not change the state of the SCL line if another device clock is still within its low period. Therefore, synchronized clock SCL is held low by the device with the longest low period. Devices with shorter low periods enter a high wait state during this time (see Figure 11-10). When all devices concerned have counted off their low period, the synchronized clock SCL line is released and pulled high. There is then no difference between the device clocks and the state of the SCL line and all the devices start counting their high periods. The first device to complete its high period pulls the SCL line low again. Delay SCL1 Start Counting High Period SCL2 SCL Internal Counter Reset Figure 11-10. IIC Clock Synchronization MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 173 11.4.1.8 Handshaking The clock synchronization mechanism can be used as a handshake in data transfer. Slave devices may hold the SCL low after completion of one byte transfer (9 bits). In such a case, it halts the bus clock and forces the master clock into wait states until the slave releases the SCL line. 11.4.1.9 Clock Stretching The clock synchronization mechanism can be used by slaves to slow down the bit rate of a transfer. After the master has driven SCL low the slave can drive SCL low for the required period and then release it. If the slave SCL low period is greater than the master SCL low period then the resulting SCL bus signal low period is stretched. 11.4.2 10-bit Address For 10-bit addressing, 0x11110 is used for the first 5 bits of the first address byte. Various combinations of read/write formats are possible within a transfer that includes 10-bit addressing. 11.4.2.1 Master-Transmitter Addresses a Slave-Receiver The transfer direction is not changed (see Table 11-9). When a 10-bit address follows a start condition, each slave compares the first seven bits of the first byte of the slave address (11110XX) with its own address and tests whether the eighth bit (R/W direction bit) is 0. More than one device can find a match and generate an acknowledge (A1). Then, each slave that finds a match compares the eight bits of the second byte of the slave address with its own address. Only one slave finds a match and generates an acknowledge (A2). The matching slave remains addressed by the master until it receives a stop condition (P) or a repeated start condition (Sr) followed by a different slave address. Slave Address 1st 7 bits S 11110 + AD10 + AD9 0 R/W A1 AD[8:1] Slave Address 2nd byte A2 Data A ... Data A/A P Table 11-9. Master-Transmitter Addresses Slave-Receiver with a 10-bit Address After the master-transmitter has sent the first byte of the 10-bit address, the slave-receiver sees an IIC interrupt. Software must ensure the contents of IICD are ignored and not treated as valid data for this interrupt. 11.4.2.2 Master-Receiver Addresses a Slave-Transmitter The transfer direction is changed after the second R/W bit (see Table 11-10). Up to and including acknowledge bit A2, the procedure is the same as that described for a master-transmitter addressing a slave-receiver. After the repeated start condition (Sr), a matching slave remembers that it was addressed before. This slave then checks whether the first seven bits of the first byte of the slave address following Sr are the same as they were after the start condition (S) and tests whether the eighth (R/W) bit is 1. If there is a match, the slave considers that it has been addressed as a transmitter and generates acknowledge A3. The slave-transmitter remains addressed until it receives a stop condition (P) or a repeated start condition (Sr) followed by a different slave address. MC9S08JM60 Series Data Sheet, Rev. 3 174 Freescale Semiconductor After a repeated start condition (Sr), all other slave devices also compare the first seven bits of the first byte of the slave address with their own addresses and test the eighth (R/W) bit. However, none of them are addressed because R/W = 1 (for 10-bit devices) or the 11110XX slave address (for 7-bit devices) does not match. S Slave Address 1st 7 bits 11110 + AD10 + AD9 R/W A1 0 Slave Address 2nd byte AD[8:1] A2 Sr Slave Address 1st 7 bits 11110 + AD10 + AD9 R/W A3 1 Data A ... Data A P Table 11-10. Master-Receiver Addresses a Slave-Transmitter with a 10-bit Address After the master-receiver has sent the first byte of the 10-bit address, the slave-transmitter sees an IIC interrupt. Software must ensure the contents of IICD are ignored and not treated as valid data for this interrupt. 11.4.3 General Call Address General calls can be requested in 7-bit address or 10-bit address. If the GCAEN bit is set, the IIC matches the general call address as well as its own slave address. When the IIC responds to a general call, it acts as a slave-receiver and the IAAS bit is set after the address cycle. Software must read the IICD register after the first byte transfer to determine whether the address matches is its own slave address or a general call. If the value is 00, the match is a general call. If the GCAEN bit is clear, the IIC ignores any data supplied from a general call address by not issuing an acknowledgement. 11.5 Resets The IIC is disabled after reset. The IIC cannot cause an MCU reset. 11.6 Interrupts The IIC generates a single interrupt. An interrupt from the IIC is generated when any of the events in Table 11-11 occur, provided the IICIE bit is set. The interrupt is driven by bit IICIF (of the IIC status register) and masked with bit IICIE (of the IIC control register). The IICIF bit must be cleared by software by writing a 1 to it in the interrupt routine. You can determine the interrupt type by reading the status register. Table 11-11. Interrupt Summary Interrupt Source Complete 1-byte transfer Match of received calling address Arbitration Lost Status TCF IAAS ARBL Flag IICIF IICIF IICIF Local Enable IICIE IICIE IICIE 11.6.1 Byte Transfer Interrupt The TCF (transfer complete flag) bit is set at the falling edge of the ninth clock to indicate the completion of byte transfer. MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 175 11.6.2 Address Detect Interrupt When the calling address matches the programmed slave address (IIC address register) or when the GCAEN bit is set and a general call is received, the IAAS bit in the status register is set. The CPU is interrupted, provided the IICIE is set. The CPU must check the SRW bit and set its Tx mode accordingly. 11.6.3 Arbitration Lost Interrupt The IIC is a true multi-master bus that allows more than one master to be connected on it. If two or more masters try to control the bus at the same time, the relative priority of the contending masters is determined by a data arbitration procedure. The IIC module asserts this interrupt when it loses the data arbitration process and the ARBL bit in the status register is set. Arbitration is lost in the following circumstances: • SDA sampled as a low when the master drives a high during an address or data transmit cycle. • SDA sampled as a low when the master drives a high during the acknowledge bit of a data receive cycle. • A start cycle is attempted when the bus is busy. • A repeated start cycle is requested in slave mode. • A stop condition is detected when the master did not request it. This bit must be cleared by software writing a 1 to it. MC9S08JM60 Series Data Sheet, Rev. 3 176 Freescale Semiconductor 11.7 Initialization/Application Information Module Initialization (Slave) 1. Write: IICC2 — to enable or disable general call — to select 10-bit or 7-bit addressing mode 2. Write: IICA — to set the slave address 3. Write: IICC1 — to enable IIC and interrupts 4. Initialize RAM variables (IICEN = 1 and IICIE = 1) for transmit data 5. Initialize RAM variables used to achieve the routine shown in Figure 11-12 Module Initialization (Master) 1. Write: IICF — to set the IIC baud rate (example provided in this chapter) 2. Write: IICC1 — to enable IIC and interrupts 3. Initialize RAM variables (IICEN = 1 and IICIE = 1) for transmit data 4. Initialize RAM variables used to achieve the routine shown in Figure 11-12 5. Write: IICC1 — to enable TX Register Model IICA MULT AD[7:1] 0 When addressed as a slave (in slave mode), the module responds to this address IICF ICR Baud rate = BUSCLK / (2 x MULT x (SCL DIVIDER)) IICC1 IICS IICD IICEN TCF IICIE IAAS MST BUSY TX ARBL DATA Data register; Write to transmit IIC data read to read IIC data IICC2 GCAEN ADEXT Address configuration 0 0 0 AD10 AD9 AD8 TXAK 0 RSTA SRW 0 IICIF 0 RXAK Module configuration Module status flags Figure 11-11. IIC Module Quick Start MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 177 Clear IICIF Y Master Mode ? N TX Tx/Rx ? RX Y Arbitration Lost ? N Last Byte Transmitted ? N Y Clear ARBL RXAK=0 ? Y N Last Byte to Be Read ? N N Y IAAS=1 ? Y Y IAAS=1 ? N Data Transfer See Note 2 TX/RX ? TX RX Address Transfer See Note 1 Y End of Addr Cycle (Master Rx) ? N Y 2nd Last Byte to Be Read ? N Y (Read) SRW=1 ? N (Write) Write Next Byte to IICD Set TXACK =1 Generate Stop Signal (MST = 0) Set TX Mode Y ACK from Receiver ? N Read Data from IICD and Store Write Data to IICD Tx Next Byte Switch to Rx Mode Set RX Mode Switch to Rx Mode Dummy Read from IICD Generate Stop Signal (MST = 0) Read Data from IICD and Store Dummy Read from IICD Dummy Read from IICD RTI NOTES: 1. If general call is enabled, a check must be done to determine whether the received address was a general call address (0x00). If the received address was a general call address, then the general call must be handled by user software. 2. When 10-bit addressing is used to address a slave, the slave sees an interrupt following the first byte of the extended address. Figure 11-12. Typical IIC Interrupt Routine MC9S08JM60 Series Data Sheet, Rev. 3 178 Freescale Semiconductor MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 179 MC9S08JM60 Series Data Sheet, Rev. 3 180 Freescale Semiconductor Chapter 12 Multi-Purpose Clock Generator (S08MCGV1) 12.1 Introduction The multi-purpose clock generator (MCG) module provides several clock source choices for the MCU. which contains a frequency-locked loop (FLL) and a phase-locked loop (PLL). The module can select either of the FLL or PLL clocks, or either of the internal or external reference clocks as a source for the MCU system clock. Whichever clock source is chosen, it is passed through a reduced bus divider which allows a lower output clock frequency to be derived. The MCG also controls an external oscillator (XOSC) for the use of a crystal or resonator as the external reference clock. For USB operation on the MC9S08JM60 series, the MCG must be configured for PLL engaged external (PEE) mode in order to achieve a MCGOUT frequency of 48 MHz MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 181 Chapter 12 Multi-Purpose Clock Generator (S08MCGV1) USBDP USBDN PORT A 6 PTA5– PTA0 PTB7/ADP7 PTB6/ADP6 PTB5/KBIP5/ADP5 PTB4/KBIP4/ADP4 PTB3/SS2/ADP3 PTB2/SPSCK2/ADP2 PTB1/MOSI2/ADP1 PTB0/MISO2/ADP0 PTC6 PTC5/RxD2 PTC4 PTC3/TxD2 PTC2 PTC1/SDA PTC0/SCL HCS08 CORE ON-CHIP ICE AND DEBUG MODULE (DBG) FULL SPEED USB USB ENDPOINT TRANSCEIVER RAM 8-/16-BIT SERIAL PERIPHERAL INTERFACE MODULE (SPI2) SS2 SPSCK2 MOSI2 MISO2 RxD2 TxD2 SDA SCL USB SIE BKGD/MS BDC CPU RESET HCS08 SYSTEM CONTROL RESETS AND INTERRUPTS MODES OF OPERATION POWER MANAGEMENT IRQ/TPMCLK SERIAL COMMUNICATIONS INTERFACE MODULE (SCI2) COP IRQ LVD IIC MODULE (IIC) VDDAD VSSAD VREFL VREFH USER Flash (IN BYTES) MC9S08JM60 = 60,912 MC9S08JM32 = 32,768 12-CHANNEL, 12-BIT ANALOG-TO-DIGITAL CONVERTER (ADC) 8 4 PORT D PORT C PORT B ACMP– ANALOG COMPARATOR (ACMP) ACMP+ ACMPO SS1 SPSCK1 MOSI1 MISO1 6-CHANNEL TIMER/PWM MODULE (TPM1) SERIAL COMMUNICATIONS INTERFACE MODULE (SCI1) PORT E TPMCLK TPM1CH1 TPM1CH0 TPM1CHx 4 RxD1 TxD1 TPMCLK TPM2CH1 TPM2CH0 KBIPx 8-BIT KEYBOARD INTERRUPT MODULE (KBI) KBIPx EXTAL XTAL PTD7 PTD6 PTD5 PTD4/ADP11 PTD3/KBIP3/ADP10 PTD2/KBIP2/ACMPO PTD1/ADP9/ACMP– PTD0/ADP8/ACMP+ PTE7/SS1 PTE6/SPSCK1 PTE5/MOSI1 PTE4/MISO1 PTE3/TPM1CH1 PTE2/TPM1CH0 PTE1/RxD1 PTE0/TxD1 PTF7 PTF6 PTF5/TPM2CH1 PTF4/TPM2CH0 PTF3/TPM1CH5 PTF2/TPM1CH4 PTF1/TPM1CH3 PTF0/TPM1CH2 PTG5/EXTAL PTG4/XTAL PTG3/KBIP7 PTG2/KBIP6 PTG1/KBIP1 PTG0/KBIP0 USER RAM (IN BYTES) MC9S08JM60 = 4096 MC9S08JM32 = 2048 8-/16-BIT SERIAL PERIPHERAL INTERFACE MODULE (SPI1) MULTI-PURPOSE CLOCK GENERATOR (MCG) VSSOSC LOW-POWER OSCILLATOR SYSTEM VOLTAGE REGULATOR USB 3.3-V VOLTAGE REGULATOR REAL-TIME COUNTER (RTC) VDD VSS MODULE (TPM2) VUSB33 4 4 NOTES: 1. Port pins are software configurable with pullup device if input port. 2. Pin contains software configurable pullup/pull-down device if IRQ is enabled (IRQPE = 1). Pull-down is enabled if rising edge detect is selected (IRQEDG = 1) 3. IRQ does not have a clamp diode to VDD. IRQ must not be driven above VDD. 4. Pin contains integrated pullup device. 5. When pin functions as KBI (KBIPEn = 1) and associated pin is configured to enable the pullup device, KBEDGn can be used to reconfigure the pullup as a pull-down device. Figure 12-1. MC9S08JM60 Series Block Diagram Highlighting MCG Block and Pins MC9S08JM60 Series Data Sheet, Rev. 3 182 Freescale Semiconductor PORT G PORT F 2-CHANNEL TIMER/PWM Multi-Purpose Clock Generator (S08MCGV1) 12.1.1 Features Key features of the MCG module are: • Frequency-locked loop (FLL) — 0.2% resolution using internal 32-kHz reference — 2% deviation over voltage and temperature using internal 32-kHz reference — Internal or external reference can be used to control the FLL • Phase-locked loop (PLL) — Voltage-controlled oscillator (VCO) — Modulo VCO frequency divider — Phase/Frequency detector — Integrated loop filter — Lock detector with interrupt capability • Internal reference clock — Nine trim bits for accuracy — Can be selected as the clock source for the MCU • External reference clock — Control for external oscillator — Clock monitor with reset capability — Can be selected as the clock source for the MCU • Reference divider is provided • Clock source selected can be divided down by 1, 2, 4, or 8 • BDC clock (MCGLCLK) is provided as a constant divide by 2 of the DCO output whether in an FLL or PLL mode. MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 183 Multi-Purpose Clock Generator (S08MCGV1) External Oscillator (XOSC) RANGE HGO CME Clock Monitor EREFS EREFSTEN IREFSTEN ERCLKEN IRCLKEN CLKS BDIV MCGERCLK MCGIRCLK / 2n Internal Reference Clock LP n=0-3 MCGOUT LOC OSCINIT IREFS 9 TRIM DCO DCOOUT PLLS /2 n RDIV_CLK Lock Detector Filter FLL LOLS LOCK MCGFFCLK LP VCOOUT /2 MCGLCLK n=0-7 RDIV Phase Detector VDIV Charge Pump Internal Filter PLL VCO /(4,8,12,...,40) Multi-purpose Clock Generator (MCG) Figure 12-2. Multi-Purpose Clock Generator (MCG) Block Diagram MC9S08JM60 Series Data Sheet, Rev. 3 184 Freescale Semiconductor Multi-Purpose Clock Generator (S08MCGV1) 12.1.2 Modes of Operation There are nine modes of operation for the MCG: • FLL Engaged Internal (FEI) • FLL Engaged External (FEE) • FLL Bypassed Internal (FBI) • FLL Bypassed External (FBE) • PLL Engaged External (PEE) • PLL Bypassed External (PBE) • Bypassed Low Power Internal (BLPI) • Bypassed Low Power External (BLPE) • Stop For details see Section 12.4.1, “Operational Modes.” 12.2 External Signal Description There are no MCG signals that connect off chip. MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 185 Multi-Purpose Clock Generator (S08MCGV1) 12.3 12.3.1 Register Definition MCG Control Register 1 (MCGC1) 7 6 5 4 3 2 1 0 R CLKS W Reset: 0 0 0 0 0 1 0 0 RDIV IREFS IRCLKEN IREFSTEN Figure 12-3. MCG Control Register 1 (MCGC1) Table 12-1. MCG Control Register 1 Field Descriptions Field 7:6 CLKS Description Clock Source Select — Selects the system clock source. 00 Encoding 0 — Output of FLL or PLL is selected. 01 Encoding 1 — Internal reference clock is selected. 10 Encoding 2 — External reference clock is selected. 11 Encoding 3 — Reserved, defaults to 00. Reference Divider — Selects the amount to divide down the reference clock selected by the IREFS bit. If the FLL is selected, the resulting frequency must be in the range 31.25 kHz to 39.0625 kHz. If the PLL is selected, the resulting frequency must be in the range 1 MHz to 2 MHz. 000 Encoding 0 — Divides reference clock by 1 (reset default) 001 Encoding 1 — Divides reference clock by 2 010 Encoding 2 — Divides reference clock by 4 011 Encoding 3 — Divides reference clock by 8 100 Encoding 4 — Divides reference clock by 16 101 Encoding 5 — Divides reference clock by 32 110 Encoding 6 — Divides reference clock by 64 111 Encoding 7 — Divides reference clock by 128 Internal Reference Select — Selects the reference clock source. 1 Internal reference clock selected 0 External reference clock selected Internal Reference Clock Enable — Enables the internal reference clock for use as MCGIRCLK. 1 MCGIRCLK active 0 MCGIRCLK inactive Internal Reference Stop Enable — Controls whether or not the internal reference clock remains enabled when the MCG enters stop mode. 1 Internal reference clock stays enabled in stop if IRCLKEN is set or if MCG is in FEI, FBI, or BLPI mode before entering stop 0 Internal reference clock is disabled in stop 5:3 RDIV 2 IREFS 1 IRCLKEN 0 IREFSTEN MC9S08JM60 Series Data Sheet, Rev. 3 186 Freescale Semiconductor Multi-Purpose Clock Generator (S08MCGV1) 12.3.2 MCG Control Register 2 (MCGC2) 7 6 5 4 3 2 1 0 R BDIV W Reset: 0 1 0 0 0 0 0 0 RANGE HGO LP EREFS ERCLKEN EREFSTEN Figure 12-4. MCG Control Register 2 (MCGC2) Table 12-2. MCG Control Register 2 Field Descriptions Field 7:6 BDIV Description Bus Frequency Divider — Selects the amount to divide down the clock source selected by the CLKS bits in the MCGC1 register. This controls the bus frequency. 00 Encoding 0 — Divides selected clock by 1 01 Encoding 1 — Divides selected clock by 2 (reset default) 10 Encoding 2 — Divides selected clock by 4 11 Encoding 3 — Divides selected clock by 8 Frequency Range Select — Selects the frequency range for the external oscillator or external clock source. 1 High frequency range selected for the external oscillator of 1 MHz to 16 MHz (1 MHz to 40 MHz for external clock source) 0 Low frequency range selected for the external oscillator of 32 kHz to 100 kHz (32 kHz to 1 MHz for external clock source) High Gain Oscillator Select — Controls the external oscillator mode of operation. 1 Configure external oscillator for high gain operation 0 Configure external oscillator for low power operation Low Power Select — Controls whether the FLL (or PLL) is disabled in bypassed modes. 1 FLL (or PLL) is disabled in bypass modes (lower power). 0 FLL (or PLL) is not disabled in bypass modes. External Reference Select — Selects the source for the external reference clock. 1 Oscillator requested 0 External Clock Source requested External Reference Enable — Enables the external reference clock for use as MCGERCLK. 1 MCGERCLK active 0 MCGERCLK inactive 5 RANGE 4 HGO 3 LP 2 EREFS 1 ERCLKEN 0 External Reference Stop Enable — Controls whether or not the external reference clock remains enabled when EREFSTEN the MCG enters stop mode. 1 External reference clock stays enabled in stop if ERCLKEN is set or if MCG is in FEE, FBE, PEE, PBE, or BLPE mode before entering stop 0 External reference clock is disabled in stop MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 187 Multi-Purpose Clock Generator (S08MCGV1) 12.3.3 MCG Trim Register (MCGTRM) 7 6 5 4 3 2 1 0 R TRIM W POR: Reset: 1 U 0 U 0 U 0 U 0 U 0 U 0 U 0 U Figure 12-5. MCG Trim Register (MCGTRM) Table 12-3. MCG Trim Register Field Descriptions Field 7:0 TRIM Description MCG Trim Setting — Controls the internal reference clock frequency by controlling the internal reference clock period. The TRIM bits are binary weighted (i.e., bit 1 will adjust twice as much as bit 0). Increasing the binary value in TRIM will increase the period, and decreasing the value will decrease the period. An additional fine trim bit is available in MCGSC as the FTRIM bit. If a TRIM[7:0] value stored in nonvolatile memory is to be used, it’s the user’s responsibility to copy that value from the nonvolatile memory location to this register. MC9S08JM60 Series Data Sheet, Rev. 3 188 Freescale Semiconductor Multi-Purpose Clock Generator (S08MCGV1) 12.3.4 MCG Status and Control Register (MCGSC) 7 6 5 4 3 2 1 0 R W POR: Reset: LOLS LOCK PLLST IREFST CLKST OSCINIT FTRIM 0 0 0 0 0 0 1 1 0 0 0 0 0 0 0 U Figure 12-6. MCG Status and Control Register (MCGSC) Table 12-4. MCG Status and Control Register Field Descriptions Field 7 LOLS Description Loss of Lock Status — This bit is a sticky indication of lock status for the FLL or PLL. LOLS is set when lock detection is enabled and after acquiring lock, the FLL or PLL output frequency has fallen outside the lock exit frequency tolerance, Dunl. LOLIE determines whether an interrupt request is made when set. LOLS is cleared by reset or by writing a logic 1 to LOLS when LOLS is set. Writing a logic 0 to LOLS has no effect. 0 FLL or PLL has not lost lock since LOLS was last cleared. 1 FLL or PLL has lost lock since LOLS was last cleared. Lock Status — Indicates whether the FLL or PLL has acquired lock. Lock detection is disabled when both the FLL and PLL are disabled. If the lock status bit is set then changing the value of any of the following bits IREFS, PLLS, RDIV[2:0], TRIM[7:0] (if in FEI or FBI modes), or VDIV[3:0] (if in PBE or PEE modes), will cause the lock status bit to clear and stay cleared until the FLL or PLL has reacquired lock. Stop mode entry will also cause the lock status bit to clear and stay cleared until the FLL or PLL has reacquired lock. Entry into BLPI or BLPE mode will also cause the lock status bit to clear and stay cleared until the MCG has exited these modes and the FLL or PLL has reacquired lock. 0 FLL or PLL is currently unlocked. 1 FLL or PLL is currently locked. PLL Select Status — The PLLST bit indicates the current source for the PLLS clock. The PLLST bit does not update immediately after a write to the PLLS bit due to internal synchronization between clock domains. 0 Source of PLLS clock is FLL clock. 1 Source of PLLS clock is PLL clock. Internal Reference Status — The IREFST bit indicates the current source for the reference clock. The IREFST bit does not update immediately after a write to the IREFS bit due to internal synchronization between clock domains. 0 Source of reference clock is external reference clock (oscillator or external clock source as determined by the EREFS bit in the MCGC2 register). 1 Source of reference clock is internal reference clock. Clock Mode Status — The CLKST bits indicate the current clock mode. The CLKST bits do not update immediately after a write to the CLKS bits due to internal synchronization between clock domains. 00 Encoding 0 — Output of FLL is selected. 01 Encoding 1 — Internal reference clock is selected. 10 Encoding 2 — External reference clock is selected. 11 Encoding 3 — Output of PLL is selected. 6 LOCK 5 PLLST 4 IREFST 3:2 CLKST MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 189 Multi-Purpose Clock Generator (S08MCGV1) Table 12-4. MCG Status and Control Register Field Descriptions (continued) Field 1 OSCINIT Description OSC Initialization — If the external reference clock is selected by ERCLKEN or by the MCG being in FEE, FBE, PEE, PBE, or BLPE mode, and if EREFS is set, then this bit is set after the initialization cycles of the external oscillator clock have completed. This bit is only cleared when either EREFS is cleared or when the MCG is in either FEI, FBI, or BLPI mode and ERCLKEN is cleared. MCG Fine Trim — Controls the smallest adjustment of the internal reference clock frequency. Setting FTRIM will increase the period and clearing FTRIM will decrease the period by the smallest amount possible. If an FTRIM value stored in nonvolatile memory is to be used, it’s the user’s responsibility to copy that value from the nonvolatile memory location to this register’s FTRIM bit. 0 FTRIM 12.3.5 MCG Control Register 3 (MCGC3) 7 6 5 4 3 2 1 0 R LOLIE W Reset: 0 0 0 PLLS CME 0 VDIV 0 0 0 0 1 Figure 12-7. MCG PLL Register (MCGPLL) Table 12-5. MCG PLL Register Field Descriptions Field 7 LOLIE Description Loss of Lock Interrupt Enable — Determines if an interrupt request is made following a loss of lock indication. The LOLIE bit only has an effect when LOLS is set. 0 No request on loss of lock. 1 Generate an interrupt request on loss of lock. PLL Select — Controls whether the PLL or FLL is selected. If the PLLS bit is clear, the PLL is disabled in all modes. If the PLLS is set, the FLL is disabled in all modes. 1 PLL is selected 0 FLL is selected 6 PLLS MC9S08JM60 Series Data Sheet, Rev. 3 190 Freescale Semiconductor Multi-Purpose Clock Generator (S08MCGV1) Table 12-5. MCG PLL Register Field Descriptions (continued) Field 5 CME Description Clock Monitor Enable — Determines if a reset request is made following a loss of external clock indication. The CME bit should only be set to a logic 1 when either the MCG is in an operational mode that uses the external clock (FEE, FBE, PEE, PBE, or BLPE) or the external reference is enabled (ERCLKEN=1 in the MCGC2 register). Whenever the CME bit is set to a logic 1, the value of the RANGE bit in the MCGC2 register should not be changed. 0 Clock monitor is disabled. 1 Generate a reset request on loss of external clock. VCO Divider — Selects the amount to divide down the VCO output of PLL. The VDIV bits establish the multiplication factor (M) applied to the reference clock frequency. 0000 Encoding 0 — Reserved. 0001 Encoding 1 — Multiply by 4. 0010 Encoding 2 — Multiply by 8. 0011 Encoding 3 — Multiply by 12. 0100 Encoding 4 — Multiply by 16. 0101 Encoding 5 — Multiply by 20. 0110 Encoding 6 — Multiply by 24. 0111 Encoding 7 — Multiply by 28. 1000 Encoding 8 — Multiply by 32. 1001 Encoding 9 — Multiply by 36. 1010 Encoding 10 — Multiply by 40. 1011 Encoding 11 — Reserved (default to M=40). 11xx Encoding 12-15 — Reserved (default to M=40). 3:0 VDIV MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 191 Multi-Purpose Clock Generator (S08MCGV1) 12.4 12.4.1 Functional Description Operational Modes IREFS=1 CLKS=00 PLLS=0 IREFS=1 CLKS=01 PLLS=0 BDM Enabled or LP=0 FLL Engaged Internal (FEI) FLL Engaged External (FEE) IREFS=0 CLKS=00 PLLS=0 IREFS=0 CLKS=10 PLLS=0 BDM Enabled or LP=0 FLL Bypassed Internal (FBI) FLL Bypassed External (FBE) IREFS=0 CLKS=10 BDM Disabled and LP=1 Bypassed IREFS=1 Low Power CLKS=01 Internal (BLPI) BDM Disabled and LP=1 Bypassed Low Power External (BLPE) PLL Bypassed External (PBE) IREFS=0 CLKS=10 PLLS=1 BDM Enabled or LP=0 IREFS=0 CLKS=00 PLLS=1 PLL Engaged External (PEE) Entered from any state when MCU enters stop Stop Returns to state that was active before MCU entered stop, unless RESET occurs while in stop. Figure 12-8. Clock Switching Modes The nine states of the MCG are shown as a state diagram and are described below. The arrows indicate the allowed movements between the states. 12.4.1.1 FLL Engaged Internal (FEI) FLL engaged internal (FEI) is the default mode of operation and is entered when all the following conditions occur: • CLKS bits are written to 00 • IREFS bit is written to 1 • PLLS bit is written to 0 • RDIV bits are written to 000. Since the internal reference clock frequency should already be in the range of 31.25 kHz to 39.0625 kHz after it is trimmed, no further frequency divide is necessary. MC9S08JM60 Series Data Sheet, Rev. 3 192 Freescale Semiconductor Multi-Purpose Clock Generator (S08MCGV1) In FLL engaged internal mode, the MCGOUT clock is derived from the FLL clock, which is controlled by the internal reference clock. The FLL clock frequency locks to 1024 times the reference frequency, as selected by the RDIV bits. The MCGLCLK is derived from the FLL and the PLL is disabled in a low power state. 12.4.1.2 • • • • FLL Engaged External (FEE) The FLL engaged external (FEE) mode is entered when all the following conditions occur: CLKS bits are written to 00 IREFS bit is written to 0 PLLS bit is written to 0 RDIV bits are written to divide reference clock to be within the range of 31.25 kHz to 39.0625 kHz In FLL engaged external mode, the MCGOUT clock is derived from the FLL clock which is controlled by the external reference clock. The external reference clock which is enabled can be an external crystal/resonator or it can be another external clock source.The FLL clock frequency locks to 1024 times the reference frequency, as selected by the RDIV bits. The MCGLCLK is derived from the FLL and the PLL is disabled in a low power state. 12.4.1.3 FLL Bypassed Internal (FBI) In FLL bypassed internal (FBI) mode, the MCGOUT clock is derived from the internal reference clock and the FLL is operational but its output clock is not used. This mode is useful to allow the FLL to acquire its target frequency while the MCGOUT clock is driven from the internal reference clock. The FLL bypassed internal mode is entered when all the following conditions occur: • CLKS bits are written to 01 • IREFS bit is written to 1 • PLLS bit is written to 0 • RDIV bits are written to 000. Since the internal reference clock frequency should already be in the range of 31.25 kHz to 39.0625 kHz after it is trimmed, no further frequency divide is necessary. • LP bit is written to 0 In FLL bypassed internal mode, the MCGOUT clock is derived from the internal reference clock. The FLL clock is controlled by the internal reference clock, and the FLL clock frequency locks to 1024 times the reference frequency, as selected by the RDIV bits. The MCGLCLK is derived from the FLL and the PLL is disabled in a low power state. 12.4.1.4 FLL Bypassed External (FBE) In FLL bypassed external (FBE) mode, the MCGOUT clock is derived from the external reference clock and the FLL is operational but its output clock is not used. This mode is useful to allow the FLL to acquire its target frequency while the MCGOUT clock is driven from the external reference clock. The FLL bypassed external mode is entered when all the following conditions occur: MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 193 Multi-Purpose Clock Generator (S08MCGV1) • • • • • CLKS bits are written to 10 IREFS bit is written to 0 PLLS bit is written to 0 RDIV bits are written to divide reference clock to be within the range of 31.25 kHz to 39.0625 kHz LP bit is written to 0 In FLL bypassed external mode, the MCGOUT clock is derived from the external reference clock. The external reference clock which is enabled can be an external crystal/resonator or it can be another external clock source.The FLL clock is controlled by the external reference clock, and the FLL clock frequency locks to 1024 times the reference frequency, as selected by the RDIV bits. The MCGLCLK is derived from the FLL and the PLL is disabled in a low power state. NOTE It is possible to briefly operate in FBE mode with an FLL reference clock frequency that is greater than the specified maximum frequency. This can be necessary in applications that operate in PEE mode using an external crystal with a frequency above 5 MHz. Please see 12.5.2.4, “Example # 4: Moving from FEI to PEE Mode: External Crystal = 8 MHz, Bus Frequency = 8 MHz for a detailed example. 12.4.1.5 • • • • PLL Engaged External (PEE) The PLL engaged external (PEE) mode is entered when all the following conditions occur: CLKS bits are written to 00 IREFS bit is written to 0 PLLS bit is written to 1 RDIV bits are written to divide reference clock to be within the range of 1 MHz to 2 MHz In PLL engaged external mode, the MCGOUT clock is derived from the PLL clock which is controlled by the external reference clock. The external reference clock which is enabled can be an external crystal/resonator or it can be another external clock source The PLL clock frequency locks to a multiplication factor, as selected by the VDIV bits, times the reference frequency, as selected by the RDIV bits. If BDM is enabled then the MCGLCLK is derived from the DCO (open-loop mode) divided by two. If BDM is not enabled then the FLL is disabled in a low power state. MC9S08JM60 Series Data Sheet, Rev. 3 194 Freescale Semiconductor Multi-Purpose Clock Generator (S08MCGV1) 12.4.1.6 PLL Bypassed External (PBE) In PLL bypassed external (PBE) mode, the MCGOUT clock is derived from the external reference clock and the PLL is operational but its output clock is not used. This mode is useful to allow the PLL to acquire its target frequency while the MCGOUT clock is driven from the external reference clock. The PLL bypassed external mode is entered when all the following conditions occur: • • • • • CLKS bits are written to 10 IREFS bit is written to 0 PLLS bit is written to 1 RDIV bits are written to divide reference clock to be within the range of 1 MHz to 2 MHz LP bit is written to 0 In PLL bypassed external mode, the MCGOUT clock is derived from the external reference clock. The external reference clock which is enabled can be an external crystal/resonator or it can be another external clock source. The PLL clock frequency locks to a multiplication factor, as selected by the VDIV bits, times the reference frequency, as selected by the RDIV bits. If BDM is enabled then the MCGLCLK is derived from the DCO (open-loop mode) divided by two. If BDM is not enabled then the FLL is disabled in a low power state. 12.4.1.7 Bypassed Low Power Internal (BLPI) The bypassed low power internal (BLPI) mode is entered when all the following conditions occur: • CLKS bits are written to 01 • IREFS bit is written to 1 • PLLS bit is written to 0 or 1 • LP bit is written to 1 • BDM mode is not active In bypassed low power internal mode, the MCGOUT clock is derived from the internal reference clock. The PLL and the FLL are disabled at all times in BLPI mode and the MCGLCLK will not be available for BDC communications If the BDM becomes active the mode will switch to one of the bypassed internal modes as determined by the state of the PLLS bit. 12.4.1.8 Bypassed Low Power External (BLPE) The bypassed low power external (BLPE) mode is entered when all the following conditions occur: • CLKS bits are written to 10 • IREFS bit is written to 0 • PLLS bit is written to 0 or 1 • LP bit is written to 1 • BDM mode is not active MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 195 Multi-Purpose Clock Generator (S08MCGV1) In bypassed low power external mode, the MCGOUT clock is derived from the external reference clock. The external reference clock which is enabled can be an external crystal/resonator or it can be another external clock source. The PLL and the FLL are disabled at all times in BLPE mode and the MCGLCLK will not be available for BDC communications. If the BDM becomes active the mode will switch to one of the bypassed external modes as determined by the state of the PLLS bit. 12.4.1.9 Stop Stop mode is entered whenever the MCU enters a STOP state. In this mode, the FLL and PLL are disabled and all MCG clock signals are static except in the following cases: MCGIRCLK will be active in stop mode when all the following conditions occur: • IRCLKEN = 1 • IREFSTEN = 1 MCGERCLK will be active in stop mode when all the following conditions occur: • ERCLKEN = 1 • EREFSTEN = 1 12.4.2 Mode Switching When switching between engaged internal and engaged external modes the IREFS bit can be changed at anytime, but the RDIV bits must be changed simultaneously so that the reference frequency stays in the range required by the state of the PLLS bit (31.25 kHz to 39.0625 kHz if the FLL is selected, or 1 MHz to 2 MHz if the PLL is selected). After a change in the IREFS value the FLL or PLL will begin locking again after the switch is completed. The completion of the switch is shown by the IREFST bit. For the special case of entering stop mode immediately after switching to FBE mode, if the external clock and the internal clock are disabled in stop mode, (EREFSTEN = 0 and IREFSTEN = 0), it is necessary to allow 100us after the IREFST bit is cleared to allow the internal reference to shutdown. For most cases the delay due to instruction execution times will be sufficient. The CLKS bits can also be changed at anytime, but in order for the MCGLCLK to be configured correctly the RDIV bits must be changed simultaneously so that the reference frequency stays in the range required by the state of the PLLS bit (31.25 kHz to 39.0625 kHz if the FLL is selected, or 1 MHz to 2MHz if the PLL is selected). The actual switch to the newly selected clock will be shown by the CLKST bits. If the newly selected clock is not available, the previous clock will remain selected. For details see Figure 12-8. 12.4.3 Bus Frequency Divider The BDIV bits can be changed at anytime and the actual switch to the new frequency will occur immediately. MC9S08JM60 Series Data Sheet, Rev. 3 196 Freescale Semiconductor Multi-Purpose Clock Generator (S08MCGV1) 12.4.4 Low Power Bit Usage The low power bit (LP) is provided to allow the FLL or PLL to be disabled and thus conserve power when these systems are not being used. However, in some applications it may be desirable to enable the FLL or PLL and allow it to lock for maximum accuracy before switching to an engaged mode. Do this by writing the LP bit to 0. 12.4.5 Internal Reference Clock When IRCLKEN is set the internal reference clock signal will be presented as MCGIRCLK, which can be used as an additional clock source. The MCGIRCLK frequency can be re-targeted by trimming the period of the internal reference clock. This can be done by writing a new value to the TRIM bits in the MCGTRM register. Writing a larger value will decrease the MCGIRCLK frequency, and writing a smaller value to the MCGTRM register will increase the MCGIRCLK frequency. The TRIM bits will effect the MCGOUT frequency if the MCG is in FLL engaged internal (FEI), FLL bypassed internal (FBI), or bypassed low power internal (BLPI) mode. The TRIM and FTRIM value is initialized by POR but is not affected by other resets. Until MCGIRCLK is trimmed, programming low reference divider (RDIV) factors may result in MCGOUT frequencies that exceed the maximum chip-level frequency and violate the chip-level clock timing specifications (see the Device Overview chapter). If IREFSTEN and IRCLKEN bits are both set, the internal reference clock will keep running during stop mode in order to provide a fast recovery upon exiting stop. 12.4.6 External Reference Clock The MCG module can support an external reference clock with frequencies between 31.25 kHz to 5 MHz in FEE and FBE modes, 1 MHz to 16 MHz in PEE and PBE modes, and 0 to 40 MHz in BLPE mode. When ERCLKEN is set, the external reference clock signal will be presented as MCGERCLK, which can be used as an additional clock source. When IREFS = 1, the external reference clock will not be used by the FLL or PLL and will only be used as MCGERCLK. In these modes, the frequency can be equal to the maximum frequency the chip-level timing specifications will support (see the Device Overview chapter). If EREFSTEN and ERCLKEN bits are both set or the MCG is in FEE, FBE, PEE, PBE or BLPE mode, the external reference clock will keep running during stop mode in order to provide a fast recovery upon exiting stop. If CME bit is written to 1, the clock monitor is enabled. If the external reference falls below a certain frequency (floc_high or floc_low depending on the RANGE bit in the MCGC2), the MCU will reset. The LOC bit in the System Reset Status (SRS) register will be set to indicate the error. 12.4.7 Fixed Frequency Clock The MCG presents the divided reference clock as MCGFFCLK for use as an additional clock source. The MCGFFCLK frequency must be no more than 1/4 of the MCGOUT frequency to be valid. Because of this requirement, the MCGFFCLK is not valid in bypass modes for the following combinations of BDIV and RDIV values: MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 197 Multi-Purpose Clock Generator (S08MCGV1) • BDIV=00 (divide by 1), RDIV < 010 BDIV=01 (divide by 2), RDIV < 011 12.5 Initialization / Application Information This section describes how to initialize and configure the MCG module in application. The following sections include examples on how to initialize the MCG and properly switch between the various available modes. 12.5.1 MCG Module Initialization Sequence The MCG comes out of reset configured for FEI mode with the BDIV set for divide-by-2. The internal reference will stabilize in tirefst microseconds before the FLL can acquire lock. As soon as the internal reference is stable, the FLL will acquire lock in tfll_lock milliseconds. Upon POR, the internal reference will require trimming to guarantee an accurate clock. Freescale recommends using FLASH location 0xFFAE for storing the fine trim bit, FTRIM in the MCGSC register, and 0xFFAF for storing the 8-bit trim value in the MCGTRM register. The MCU will not automatically copy the values in these FLASH locations to the respective registers. Therefore, user code must copy these values from FLASH to the registers. NOTE The BDIV value should not be changed to divide-by-1 without first trimming the internal reference. Failure to do so could result in the MCU running out of specification. 12.5.1.1 Initializing the MCG Because the MCG comes out of reset in FEI mode, the only MCG modes which can be directly switched to upon reset are FEE, FBE, and FBI modes (see Figure 12-8). Reaching any of the other modes requires first configuring the MCG for one of these three initial modes. Care must be taken to check relevant status bits in the MCGSC register reflecting all configuration changes within each mode. To change from FEI mode to FEE or FBE modes, follow this procedure: 1. Enable the external clock source by setting the appropriate bits in MCGC2. 2. Write to MCGC1 to select the clock mode. — If entering FEE, set RDIV appropriately, clear the IREFS bit to switch to the external reference, and leave the CLKS bits at %00 so that the output of the FLL is selected as the system clock source. — If entering FBE, clear the IREFS bit to switch to the external reference and change the CLKS bits to %10 so that the external reference clock is selected as the system clock source. The RDIV bits should also be set appropriately here according to the external reference frequency because although the FLL is bypassed, it is still on in FBE mode. — The internal reference can optionally be kept running by setting the IRCLKEN bit. This is useful if the application will switch back and forth between internal and external modes. For MC9S08JM60 Series Data Sheet, Rev. 3 198 Freescale Semiconductor Multi-Purpose Clock Generator (S08MCGV1) minimum power consumption, leave the internal reference disabled while in an external clock mode. 3. After the proper configuration bits have been set, wait for the affected bits in the MCGSC register to be changed appropriately, reflecting that the MCG has moved into the proper mode. — If ERCLKEN was set in step 1 or the MCG is in FEE, FBE, PEE, PBE, or BLPE mode, and EREFS was also set in step 1, wait here for the OSCINIT bit to become set indicating that the external clock source has finished its initialization cycles and stabilized. Typical crystal startup times are given in Appendix A, “Electrical Characteristics”. — If in FEE mode, check to make sure the IREFST bit is cleared and the LOCK bit is set before moving on. — If in FBE mode, check to make sure the IREFST bit is cleared, the LOCK bit is set, and the CLKST bits have changed to %10 indicating the external reference clock has been appropriately selected. Although the FLL is bypassed in FBE mode, it is still on and will lock in FBE mode. To change from FEI clock mode to FBI clock mode, follow this procedure: 1. Change the CLKS bits to %01 so that the internal reference clock is selected as the system clock source. 2. Wait for the CLKST bits in the MCGSC register to change to %01, indicating that the internal reference clock has been appropriately selected. 12.5.2 MCG Mode Switching When switching between operational modes of the MCG, certain configuration bits must be changed in order to properly move from one mode to another. Each time any of these bits are changed (PLLS, IREFS, CLKS, or EREFS), the corresponding bits in the MCGSC register (PLLST, IREFST, CLKST, or OSCINIT) must be checked before moving on in the application software. Additionally, care must be taken to ensure that the reference clock divider (RDIV) is set properly for the mode being switched to. For instance, in PEE mode, if using a 4 MHz crystal, RDIV must be set to %001 (divide-by-2) or %010 (divide -by-4) in order to divide the external reference down to the required frequency between 1 and 2 MHz. The RDIV and IREFS bits should always be set properly before changing the PLLS bit so that the FLL or PLL clock has an appropriate reference clock frequency to switch to. MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 199 Multi-Purpose Clock Generator (S08MCGV1) The table below shows MCGOUT frequency calculations using RDIV, BDIV, and VDIV settings for each clock mode. The bus frequency is equal to MCGOUT divided by 2. Table 12-6. MCGOUT Frequency Calculation Options Clock Mode FEI (FLL engaged internal) fMCGOUT1 (fint * 1024) / B Note Typical fMCGOUT = 16 MHz immediately after reset. RDIV bits set to %000. fext / R must be in the range of 31.25 kHz to 39.0625 kHz fext / R must be in the range of 31.25 kHz to 39.0625 kHz Typical fint = 32 kHz fext / R must be in the range of 1 MHz to 2 MHz fext / R must be in the range of 1 MHz to 2 MHz FEE (FLL engaged external) FBE (FLL bypassed external) FBI (FLL bypassed internal) PEE (PLL engaged external) PBE (PLL bypassed external) BLPI (Bypassed low power internal) BLPE (Bypassed low power external) 1R (fext / R *1024) / B fext / B fint / B [(fext / R) * M] / B fext / B fint / B fext / B is the reference divider selected by the RDIV bits, B is the bus frequency divider selected by the BDIV bits, and M is the multiplier selected by the VDIV bits. This section will include 3 mode switching examples using a 4 MHz external crystal. If using an external clock source less than 1 MHz, the MCG should not be configured for any of the PLL modes (PEE and PBE). 12.5.2.1 Example # 1: Moving from FEI to PEE Mode: External Crystal = 4 MHz, Bus Frequency = 8 MHz In this example, the MCG will move through the proper operational modes from FEI to PEE mode until the 4 MHz crystal reference frequency is set to achieve a bus frequency of 8 MHz. Because the MCG is in FEI mode out of reset, this example also shows how to initialize the MCG for PEE mode out of reset. First, the code sequence will be described. Then a flowchart will be included which illustrates the sequence. 1. First, FEI must transition to FBE mode: a) MCGC2 = 0x36 (%00110110) – BDIV (bits 7 and 6) set to %00, or divide-by-1 – RANGE (bit 5) set to 1 because the frequency of 4 MHz is within the high frequency range – HGO (bit 4) set to 1 to configure external oscillator for high gain operation – EREFS (bit 2) set to 1, because a crystal is being used – ERCLKEN (bit 1) set to 1 to ensure the external reference clock is active b) Loop until OSCINIT (bit 1) in MCGSC is 1, indicating the crystal selected by the EREFS bit has been initialized. MC9S08JM60 Series Data Sheet, Rev. 3 200 Freescale Semiconductor Multi-Purpose Clock Generator (S08MCGV1) c) MCGC1 = 0xB8 (%10111000) – CLKS (bits 7 and 6) set to %10 in order to select external reference clock as system clock source – RDIV (bits 5-3) set to %111, or divide-by-128 because 4 MHz / 128 = 31.25 kHz which is in the 31.25 kHz to 39.0625 kHz range required by the FLL – IREFS (bit 2) cleared to 0, selecting the external reference clock d) Loop until IREFST (bit 4) in MCGSC is 0, indicating the external reference is the current source for the reference clock e) Loop until CLKST (bits 3 and 2) in MCGSC are %10, indicating that the external reference clock is selected to feed MCGOUT 2. Then, FBE must transition either directly to PBE mode or first through BLPE mode and then to PBE mode: a) BLPE: If a transition through BLPE mode is desired, first set LP (bit 3) in MCGC2 to 1. b) BLPE/PBE: MCGC1 = 0x90 (%10010000) – RDIV (bits 5-3) set to %010, or divide-by-4 because 4 MHz / 4 = 1 MHz which is in the 1 MHz to 2 MHz range required by the PLL. In BLPE mode, the configuration of the RDIV does not matter because both the FLL and PLL are disabled. Changing them only sets up the the dividers for PLL usage in PBE mode c) BLPE/PBE: MCGC3 = 0x44 (%01000100) – PLLS (bit 6) set to 1, selects the PLL. In BLPE mode, changing this bit only prepares the MCG for PLL usage in PBE mode – VDIV (bits 3-0) set to %0100, or multiply-by-16 because 1 MHz reference * 16 = 16 MHz. In BLPE mode, the configuration of the VDIV bits does not matter because the PLL is disabled. Changing them only sets up the multiply value for PLL usage in PBE mode d) BLPE: If transitioning through BLPE mode, clear LP (bit 3) in MCGC2 to 0 here to switch to PBE mode e) PBE: Loop until PLLST (bit 5) in MCGSC is set, indicating that the current source for the PLLS clock is the PLL f) PBE: Then loop until LOCK (bit 6) in MCGSC is set, indicating that the PLL has acquired lock 3. Last, PBE mode transitions into PEE mode: a) MCGC1 = 0x10 (%00010000) – CLKS (bits7 and 6) in MCGSC1 set to %00 in order to select the output of the PLL as the system clock source – Loop until CLKST (bits 3 and 2) in MCGSC are %11, indicating that the PLL output is selected to feed MCGOUT in the current clock mode b) Now, With an RDIV of divide-by-4, a BDIV of divide-by-1, and a VDIV of multiply-by-16, MCGOUT = [(4 MHz / 4) * 16] / 1 = 16 MHz, and the bus frequency is MCGOUT / 2, or 8 MHz MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 201 Multi-Purpose Clock Generator (S08MCGV1) START IN FEI MODE MCGC2 = $36 IN BLPE MODE ? (LP=1) CHECK OSCINIT = 1 ? NO YES MCGC2 = $36 (LP = 0) NO YES MCGC1 = $B8 CHECK PLLST = 1? CHECK IREFST = 0? YES CHECK LOCK = 1? CHECK CLKST = %10? NO YES YES MCGC1 = $10 NO NO YES NO ENTER BLPE MODE ? NO CHECK CLKST = %11? NO YES MCGC2 = $3E (LP = 1) YES CONTINUE IN PEE MODE MCGC1 = $90 MCGC3 = $44 Figure 12-9. Flowchart of FEI to PEE Mode Transition using a 4 MHz Crystal MC9S08JM60 Series Data Sheet, Rev. 3 202 Freescale Semiconductor Multi-Purpose Clock Generator (S08MCGV1) 12.5.2.2 Example # 2: Moving from PEE to BLPI Mode: External Crystal = 4 MHz, Bus Frequency =16 kHz In this example, the MCG will move through the proper operational modes from PEE mode with a 4 MHz crystal configured for an 8 MHz bus frequency (see previous example) to BLPI mode with a 16 kHz bus frequency.First, the code sequence will be described. Then a flowchart will be included which illustrates the sequence. 1. First, PEE must transition to PBE mode: a) MCGC1 = 0x90 (%10010000) – CLKS (bits 7 and 6) set to %10 in order to switch the system clock source to the external reference clock b) Loop until CLKST (bits 3 and 2) in MCGSC are %10, indicating that the external reference clock is selected to feed MCGOUT 2. Then, PBE must transition either directly to FBE mode or first through BLPE mode and then to FBE mode: a) BLPE: If a transition through BLPE mode is desired, first set LP (bit 3) in MCGC2 to 1 b) BLPE/FBE: MCGC1 = 0xB8 (%10111000) – RDIV (bits 5-3) set to %111, or divide-by-128 because 4 MHz / 128 = 31.25 kHz which is in the 31.25 kHz to 39.0625 kHz range required by the FLL. In BLPE mode, the configuration of the RDIV does not matter because both the FLL and PLL are disabled. Changing them only sets up the dividers for FLL usage in FBE mode c) BLPE/FBE: MCGC3 = 0x04 (%00000100) – PLLS (bit 6) clear to 0 to select the FLL. In BLPE mode, changing this bit only prepares the MCG for FLL usage in FBE mode. With PLLS = 0, the VDIV value does not matter. d) BLPE: If transitioning through BLPE mode, clear LP (bit 3) in MCGC2 to 0 here to switch to FBE mode e) FBE: Loop until PLLST (bit 5) in MCGSC is clear, indicating that the current source for the PLLS clock is the FLL f) FBE: Optionally, loop until LOCK (bit 6) in the MCGSC is set, indicating that the FLL has acquired lock. Although the FLL is bypassed in FBE mode, it is still enabled and running. 3. Next, FBE mode transitions into FBI mode: a) MCGC1 = 0x44 (%01000100) – CLKS (bits7 and 6) in MCGSC1 set to %01 in order to switch the system clock to the internal reference clock – IREFS (bit 2) set to 1 to select the internal reference clock as the reference clock source – RDIV (bits 5-3) set to %000, or divide-by-1 because the trimmed internal reference should be within the 31.25 kHz to 39.0625 kHz range required by the FLL b) Loop until IREFST (bit 4) in MCGSC is 1, indicating the internal reference clock has been selected as the reference clock source c) Loop until CLKST (bits 3 and 2) in MCGSC are %01, indicating that the internal reference clock is selected to feed MCGOUT MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 203 Multi-Purpose Clock Generator (S08MCGV1) 4. Lastly, FBI transitions into FBILP mode. a) MCGC2 = 0x08 (%00001000) – LP (bit 3) in MCGSC is 1 START IN PEE MODE MCGC1 = $90 CHECK PLLST = 0? CHECK CLKST = %10 ? NO NO YES YES ENTER BLPE MODE ? OPTIONAL: CHECK LOCK = 1? NO YES MCGC1 = $44 NO YES MCGC2 = $3E CHECK IREFST = 0? MCGC1 = $B8 MCGC3 = $04 YES NO IN BLPE MODE ? (LP=1) NO CHECK CLKST = %01? NO YES YES MCGC2 = $36 (LP = 0) MCGC2 = $08 CONTINUE IN BLPI MODE Figure 12-10. Flowchart of PEE to BLPI Mode Transition using a 4 MHz Crystal MC9S08JM60 Series Data Sheet, Rev. 3 204 Freescale Semiconductor Multi-Purpose Clock Generator (S08MCGV1) 12.5.2.3 Example #3: Moving from BLPI to FEE Mode: External Crystal = 4 MHz, Bus Frequency = 16 MHz In this example, the MCG will move through the proper operational modes from BLPI mode at a 16 kHz bus frequency running off of the internal reference clock (see previous example) to FEE mode using a 4 MHz crystal configured for a 16 MHz bus frequency. First, the code sequence will be described. Then a flowchart will be included which illustrates the sequence. 1. First, BLPI must transition to FBI mode. a) MCGC2 = 0x00 (%00000000) – LP (bit 3) in MCGSC is 0 b) Optionally, loop until LOCK (bit 6) in the MCGSC is set, indicating that the FLL has acquired lock. Although the FLL is bypassed in FBI mode, it is still enabled and running. 2. Next, FBI will transition to FEE mode. a) MCGC2 = 0x36 (%00110110) – RANGE (bit 5) set to 1 because the frequency of 4 MHz is within the high frequency range – HGO (bit 4) set to 1 to configure external oscillator for high gain operation – EREFS (bit 2) set to 1, because a crystal is being used – ERCLKEN (bit 1) set to 1 to ensure the external reference clock is active b) Loop until OSCINIT (bit 1) in MCGSC is 1, indicating the crystal selected by the EREFS bit has been initialized. c) MCGC1 = 0x38 (%00111000) – CLKS (bits 7 and 6) set to %00 in order to select the output of the FLL as system clock source – RDIV (bits 5-3) set to %111, or divide-by-128 because 4 MHz / 128 = 31.25 kHz which is in the 31.25 kHz to 39.0625 kHz range required by the FLL – IREFS (bit 1) cleared to 0, selecting the external reference clock d) Loop until IREFST (bit 4) in MCGSC is 0, indicating the external reference clock is the current source for the reference clock e) Optionally, loop until LOCK (bit 6) in the MCGSC is set, indicating that the FLL has reacquired lock. f) Loop until CLKST (bits 3 and 2) in MCGSC are %00, indicating that the output of the FLL is selected to feed MCGOUT MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 205 Multi-Purpose Clock Generator (S08MCGV1) START IN BLPI MODE CHECK IREFST = 0? MCGC2 = $00 YES NO OPTIONAL: CHECK LOCK = 1? YES MCGC2 = $36 NO OPTIONAL: CHECK LOCK = 1? YES NO CHECK CLKST = %00? NO CHECK OSCINIT = 1 ? NO YES CONTINUE YES IN FEE MODE MCGC1 = $38 Figure 12-11. Flowchart of BLPI to FEE Mode Transition using a 4 MHz Crystal 12.5.2.4 Example # 4: Moving from FEI to PEE Mode: External Crystal = 8 MHz, Bus Frequency = 8 MHz In this example, the MCG will move through the proper operational modes from FEI to PEE mode until the 8 MHz crystal reference frequency is set to achieve a bus frequency of 8 MHz. This example is similar to example number one except that in this case the frequency of the external crystal is 8 MHz instead of 4 MHz. Special consideration must be taken with this case since there is a period of time along the way from FEI mode to PEE mode where the FLL operates based on a reference clock with a frequency that is greater than the maximum allowed for the FLL. This occurs because with an 8 MHz MC9S08JM60 Series Data Sheet, Rev. 3 206 Freescale Semiconductor Multi-Purpose Clock Generator (S08MCGV1) external crystal and a maximum reference divider factor of 128, the resulting frequency of the reference clock for the FLL is 62.5 kHz (greater than the 39.0625 kHz maximum allowed). Care must be taken in the software to minimize the amount of time spent in this state where the FLL is operating in this condition. The following code sequence describes how to move from FEI mode to PEE mode until the 8 MHz crystal reference frequency is set to achieve a bus frequency of 8 MHz. Because the MCG is in FEI mode out of reset, this example also shows how to initialize the MCG for PEE mode out of reset. First, the code sequence will be described. Then a flowchart will be included which illustrates the sequence. 1. First, FEI must transition to FBE mode: a) MCGC2 = 0x36 (%00110110) – BDIV (bits 7 and 6) set to %00, or divide-by-1 – RANGE (bit 5) set to 1 because the frequency of 8 MHz is within the high frequency range – HGO (bit 4) set to 1 to configure external oscillator for high gain operation – EREFS (bit 2) set to 1, because a crystal is being used – ERCLKEN (bit 1) set to 1 to ensure the external reference clock is active b) Loop until OSCINIT (bit 1) in MCGSC is 1, indicating the crystal selected by the EREFS bit has been initialized. c) Block Interrupts (If applicable by setting the interrupt bit in the CCR). d) MCGC1 = 0xB8 (%10111000) – CLKS (bits 7 and 6) set to %10 in order to select external reference clock as system clock source – RDIV (bits 5-3) set to %111, or divide-by-128. NOTE 8 MHz / 128 = 62.5 kHz which is greater than the 31.25 kHz to 39.0625 kHz range required by the FLL. Therefore after the transition to FBE is complete, software must progress through to BLPE mode immediately by setting the LP bit in MCGC2. – IREFS (bit 2) cleared to 0, selecting the external reference clock e) Loop until IREFST (bit 4) in MCGSC is 0, indicating the external reference is the current source for the reference clock f) Loop until CLKST (bits 3 and 2) in MCGSC are %10, indicating that the external reference clock is selected to feed MCGOUT 2. Then, FBE mode transitions into BLPE mode: a) MCGC2 = 0x3E (%00111110) – LP (bit 3) in MCGC2 to 1 (BLPE mode entered) NOTE There must be no extra steps (including interrupts) between steps 1d and 2a. b) Enable Interrupts (if applicable by clearing the interrupt bit in the CCR). MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 207 Multi-Purpose Clock Generator (S08MCGV1) c) MCGC1 = 0x98 (%10011000) – RDIV (bits 5-3) set to %011, or divide-by-8 because 8 MHz / 8= 1 MHz which is in the 1 MHz to 2 MHz range required by the PLL. In BLPE mode, the configuration of the RDIV does not matter because both the FLL and PLL are disabled. Changing them only sets up the the dividers for PLL usage in PBE mode d) MCGC3 = 0x44 (%01000100) – PLLS (bit 6) set to 1, selects the PLL. In BLPE mode, changing this bit only prepares the MCG for PLL usage in PBE mode – VDIV (bits 3-0) set to %0100, or multiply-by-16 because 1 MHz reference * 16 = 16 MHz. In BLPE mode, the configuration of the VDIV bits does not matter because the PLL is disabled. Changing them only sets up the multiply value for PLL usage in PBE mode e) Loop until PLLST (bit 5) in MCGSC is set, indicating that the current source for the PLLS clock is the PLL 3. Then, BLPE mode transitions into PBE mode: a) Clear LP (bit 3) in MCGC2 to 0 here to switch to PBE mode b) Then loop until LOCK (bit 6) in MCGSC is set, indicating that the PLL has acquired lock 4. Last, PBE mode transitions into PEE mode: a) MCGC1 = 0x18 (%00011000) – CLKS (bits7 and 6) in MCGSC1 set to %00 in order to select the output of the PLL as the system clock source – Loop until CLKST (bits 3 and 2) in MCGSC are %11, indicating that the PLL output is selected to feed MCGOUT in the current clock mode b) Now, With an RDIV of divide-by-8, a BDIV of divide-by-1, and a VDIV of multiply-by-16, MCGOUT = [(8 MHz / 8) * 16] / 1 = 16 MHz, and the bus frequency is MCGOUT / 2, or 8 MHz MC9S08JM60 Series Data Sheet, Rev. 3 208 Freescale Semiconductor Multi-Purpose Clock Generator (S08MCGV1) START IN FEI MODE MCGC2 = $36 CHECK OSCINIT = 1 ? NO CHECK PLLST = 1? YES NO YES MCGC2 = $36 (LP = 0) MCGC1 = $B8 CHECK IREFST = 0? YES NO CHECK LOCK = 1? NO YES CHECK CLKST = %10? NO MCGC1 = $18 YES MCGC2 = $3E (LP = 1) CHECK CLKST = %11? NO YES MCGC1 = $98 MCGC3 = $44 CONTINUE IN PEE MODE Figure 12-12. Flowchart of FEI to PEE Mode Transition using a 8 MHz Crystal MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 209 Multi-Purpose Clock Generator (S08MCGV1) 12.5.3 Calibrating the Internal Reference Clock (IRC) The IRC is calibrated by writing to the MCGTRM register first, then using the FTRIM bit to “fine tune” the frequency. We will refer to this total 9-bit value as the trim value, ranging from 0x000 to 0x1FF, where the FTRIM bit is the LSB. The trim value after a POR is always 0x100 (MCGTRM = 0x80 and FTRIM = 0). Writing a larger value will decrease the frequency and smaller values will increase the frequency. The trim value is linear with the period, except that slight variations in wafer fab processing produce slight non-linearities between trim value and period. These non-linearities are why an iterative trimming approach to search for the best trim value is recommended. In example #4 later in this section, this approach will be demonstrated. After a trim value has been found for a device, this value can be stored in FLASH memory to save the value. If power is removed from the device, the IRC can easily be re-trimmed by copying the saved value from FLASH to the MCG registers. Freescale identifies recommended FLASH locations for storing the trim value for each MCU. Consult the memory map in the data sheet for these locations. On devices that are factory trimmed, the factory trim value will be stored in these locations. 12.5.3.1 Example #5: Internal Reference Clock Trim For applications that require a tight frequency tolerance, a trimming procedure is provided that will allow a very accurate internal clock source. This section outlines one example of trimming the internal oscillator. Many other possible trimming procedures are valid and can be used. In the example below, the MCG trim will be calibrated for the 9-bit MCGTRM and FTRIM collective value. This value will be referred to as TRMVAL. MC9S08JM60 Series Data Sheet, Rev. 3 210 Freescale Semiconductor Multi-Purpose Clock Generator (S08MCGV1) Initial conditions: 1) Clock supplied from ATE has 500 μs duty period 2) MCG configured for internal reference with 8MHz bus START TRIM PROCEDURE TRMVAL = $100 n=1 MEASURE INCOMING CLOCK WIDTH (COUNT = # OF BUS CLOCKS / 8) COUNT < EXPECTED = 500 (RUNNING TOO SLOW) . CASE STATEMENT COUNT = EXPECTED = 500 COUNT > EXPECTED = 500 (RUNNING TOO FAST) TRMVAL = TRMVAL - 256/ (2**n) (DECREASING TRMVAL INCREASES THE FREQUENCY) TRMVAL = TRMVAL + 256/ (2**n) (INCREASING TRMVAL DECREASES THE FREQUENCY) STORE MCGTRM AND FTRIM VALUES IN NON-VOLATILE MEMORY CONTINUE n = n+1 IS n > 9? NO YES Figure 12-13. Trim Procedure In this particular case, the MCU has been attached to a PCB and the entire assembly is undergoing final test with automated test equipment. A separate signal or message is provided to the MCU operating under user provided software control. The MCU initiates a trim procedure as outlined in Figure 12-13 while the tester supplies a precision reference signal. If the intended bus frequency is near the maximum allowed for the device, it is recommended to trim using a reference divider value (RDIV setting) of twice the final value. After the trim procedure is complete, the reference divider can be restored. This will prevent accidental overshoot of the maximum clock frequency. MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 211 Multi-Purpose Clock Generator (S08MCGV1) MC9S08JM60 Series Data Sheet, Rev. 3 212 Freescale Semiconductor Chapter 13 Real-Time Counter (S08RTCV1) 13.1 Introduction The real-time counter (RTC) consists of one 8-bit counter, one 8-bit comparator, several binary-based and decimal-based prescaler dividers, two clock sources, and one programmable periodic interrupt. This module can be used for time-of-day, calendar or any task scheduling functions. It can also serve as a cyclic wake up from low power modes without the need of external components. MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 213 Chapter 13 Real-Time Counter (S08RTCV1) USBDP USBDN PORT A 6 PTA5– PTA0 PTB7/ADP7 PTB6/ADP6 PTB5/KBIP5/ADP5 PTB4/KBIP4/ADP4 PTB3/SS2/ADP3 PTB2/SPSCK2/ADP2 PTB1/MOSI2/ADP1 PTB0/MISO2/ADP0 PTC6 PTC5/RxD2 PTC4 PTC3/TxD2 PTC2 PTC1/SDA PTC0/SCL HCS08 CORE ON-CHIP ICE AND DEBUG MODULE (DBG) FULL SPEED USB USB ENDPOINT TRANSCEIVER RAM 8-/16-BIT SERIAL PERIPHERAL INTERFACE MODULE (SPI2) SS2 SPSCK2 MOSI2 MISO2 RxD2 TxD2 SDA SCL USB SIE BKGD/MS BDC CPU RESET HCS08 SYSTEM CONTROL RESETS AND INTERRUPTS MODES OF OPERATION POWER MANAGEMENT IRQ/TPMCLK SERIAL COMMUNICATIONS INTERFACE MODULE (SCI2) COP IRQ LVD IIC MODULE (IIC) VDDAD VSSAD VREFL VREFH USER Flash (IN BYTES) MC9S08JM60 = 60,912 MC9S08JM32 = 32,768 12-CHANNEL, 12-BIT ANALOG-TO-DIGITAL CONVERTER (ADC) 8 4 PORT D PORT C PORT B ACMP– ANALOG COMPARATOR (ACMP) ACMP+ ACMPO SS1 SPSCK1 MOSI1 MISO1 6-CHANNEL TIMER/PWM MODULE (TPM1) SERIAL COMMUNICATIONS INTERFACE MODULE (SCI1) PORT E TPMCLK TPM1CH1 TPM1CH0 TPM1CHx 4 RxD1 TxD1 TPMCLK TPM2CH1 TPM2CH0 KBIPx 8-BIT KEYBOARD INTERRUPT MODULE (KBI) KBIPx EXTAL XTAL PTD7 PTD6 PTD5 PTD4/ADP11 PTD3/KBIP3/ADP10 PTD2/KBIP2/ACMPO PTD1/ADP9/ACMP– PTD0/ADP8/ACMP+ PTE7/SS1 PTE6/SPSCK1 PTE5/MOSI1 PTE4/MISO1 PTE3/TPM1CH1 PTE2/TPM1CH0 PTE1/RxD1 PTE0/TxD1 PTF7 PTF6 PTF5/TPM2CH1 PTF4/TPM2CH0 PTF3/TPM1CH5 PTF2/TPM1CH4 PTF1/TPM1CH3 PTF0/TPM1CH2 PTG5/EXTAL PTG4/XTAL PTG3/KBIP7 PTG2/KBIP6 PTG1/KBIP1 PTG0/KBIP0 USER RAM (IN BYTES) MC9S08JM60 = 4096 MC9S08JM32 = 2048 8-/16-BIT SERIAL PERIPHERAL INTERFACE MODULE (SPI1) MULTI-PURPOSE CLOCK GENERATOR (MCG) VSSOSC LOW-POWER OSCILLATOR SYSTEM VOLTAGE REGULATOR USB 3.3-V VOLTAGE REGULATOR REAL-TIME COUNTER (RTC) VDD VSS MODULE (TPM2) VUSB33 4 4 NOTES: 1. Port pins are software configurable with pullup device if input port. 2. Pin contains software configurable pullup/pull-down device if IRQ is enabled (IRQPE = 1). Pull-down is enabled if rising edge detect is selected (IRQEDG = 1) 3. IRQ does not have a clamp diode to VDD. IRQ must not be driven above VDD. 4. Pin contains integrated pullup device. 5. When pin functions as KBI (KBIPEn = 1) and associated pin is configured to enable the pullup device, KBEDGn can be used to reconfigure the pullup as a pull-down device. Figure 13-1. MC9S08JM60 Series Block Diagram Highlighting RTC Block MC9S08JM60 Series Data Sheet, Rev. 3 214 Freescale Semiconductor PORT G PORT F 2-CHANNEL TIMER/PWM Real-Time Counter (S08RTCV1) 13.1.1 Features Features of the RTC module include: • 8-bit up-counter — 8-bit modulo match limit — Software controllable periodic interrupt on match • Three software selectable clock sources for input to prescaler with selectable binary-based and decimal-based divider values — 1 kHz internal low-power oscillator (LPO) — External clock (ERCLK) — 32 kHz internal clock (IRCLK) 13.1.2 Modes of Operation This section defines the operation in stop, wait and background debug modes. 13.1.2.1 Wait Mode The RTC continues to run in wait mode if enabled before executing the appropriate instruction. Therefore, the RTC can bring the MCU out of wait mode if the real-time interrupt is enabled. For lowest possible current consumption, the RTC should be stopped by software if not needed as an interrupt source during wait mode. 13.1.2.2 Stop Modes The RTC continues to run in stop2 or stop3 mode if the RTC is enabled before executing the STOP instruction. Therefore, the RTC can bring the MCU out of stop modes with no external components, if the real-time interrupt is enabled. The LPO clock can be used in stop2 and stop3 modes. ERCLK and IRCLK clocks are only available in stop3 mode. Power consumption is lower when all clock sources are disabled, but in that case, the real-time interrupt cannot wake up the MCU from stop modes. 13.1.2.3 Active Background Mode The RTC suspends all counting during active background mode until the microcontroller returns to normal user operating mode. Counting resumes from the suspended value as long as the RTCMOD register is not written and the RTCPS and RTCLKS bits are not altered. MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 215 Real-Time Counter (S08RTCV1) 13.1.3 Block Diagram The block diagram for the RTC module is shown in Figure 13-2. LPO ERCLK IRCLK 8-Bit Modulo (RTCMOD) VDD Clock Source Select RTCLKS Background Mode RTCLKS[0] RTCPS D Q RTIF RTC Interrupt Request 8-Bit Comparator E R Write 1 to RTIF RTIE Prescaler Divide-By RTC Clock 8-Bit Counter (RTCCNT) Figure 13-2. Real-Time Counter (RTC) Block Diagram 13.2 External Signal Description The RTC does not include any off-chip signals. 13.3 Register Definition The RTC includes a status and control register, an 8-bit counter register, and an 8-bit modulo register. Refer to the direct-page register summary in the memory section of this document for the absolute address assignments for all RTC registers.This section refers to registers and control bits only by their names and relative address offsets. Table 13-1 is a summary of RTC registers. Table 13-1. RTC Register Summary Name R RTCSC W R RTCCNT W R RTCMOD W RTCMOD RTCCNT RTIF RTCLKS RTIE RTCPS 7 6 5 4 3 2 1 0 MC9S08JM60 Series Data Sheet, Rev. 3 216 Freescale Semiconductor Real-Time Counter (S08RTCV1) 13.3.1 RTC Status and Control Register (RTCSC) RTCSC contains the real-time interrupt status flag (RTIF), the clock select bits (RTCLKS), the real-time interrupt enable bit (RTIE), and the prescaler select bits (RTCPS). 7 6 5 4 3 2 1 0 R RTIF W Reset: 0 0 0 0 0 0 0 0 RTCLKS RTIE RTCPS Figure 13-3. RTC Status and Control Register (RTCSC) Table 13-2. RTCSC Field Descriptions Field 7 RTIF Description Real-Time Interrupt Flag This status bit indicates the RTC counter register reached the value in the RTC modulo register. Writing a logic 0 has no effect. Writing a logic 1 clears the bit and the real-time interrupt request. Reset clears RTIF. 0 RTC counter has not reached the value in the RTC modulo register. 1 RTC counter has reached the value in the RTC modulo register. Real-Time Clock Source Select. These two read/write bits select the clock source input to the RTC prescaler. Changing the clock source clears the prescaler and RTCCNT counters. When selecting a clock source, ensure that the clock source is properly enabled (if applicable) to ensure correct operation of the RTC. Reset clears RTCLKS. 00 Real-time clock source is the 1-kHz low power oscillator (LPO) 01 Real-time clock source is the external clock (ERCLK) 1x Real-time clock source is the internal clock (IRCLK) Real-Time Interrupt Enable. This read/write bit enables real-time interrupts. If RTIE is set, then an interrupt is generated when RTIF is set. Reset clears RTIE. 0 Real-time interrupt requests are disabled. Use software polling. 1 Real-time interrupt requests are enabled. Real-Time Clock Prescaler Select. These four read/write bits select binary-based or decimal-based divide-by values for the clock source. See Table 13-3. Changing the prescaler value clears the prescaler and RTCCNT counters. Reset clears RTCPS. 6–5 RTCLKS 4 RTIE 3–0 RTCPS Table 13-3. RTC Prescaler Divide-by values RTCPS RTCLKS[0] 0 0 1 Off Off 1 23 210 2 25 211 3 26 212 4 27 213 5 28 214 6 29 215 7 210 216 8 1 103 9 2 10 22 11 10 104 12 24 13 102 14 5x102 105 15 103 2x105 2x103 5x103 2x104 5x104 MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 217 Real-Time Counter (S08RTCV1) 13.3.2 RTC Counter Register (RTCCNT) RTCCNT is the read-only value of the current RTC count of the 8-bit counter. 7 6 5 4 3 2 1 0 R W Reset: 0 0 0 0 RTCCNT 0 0 0 0 Figure 13-4. RTC Counter Register (RTCCNT) Table 13-4. RTCCNT Field Descriptions Field 7:0 RTCCNT Description RTC Count. These eight read-only bits contain the current value of the 8-bit counter. Writes have no effect to this register. Reset, writing to RTCMOD, or writing different values to RTCLKS and RTCPS clear the count to 0x00. 13.3.3 RTC Modulo Register (RTCMOD) 7 6 5 4 3 2 1 0 R RTCMOD W Reset: 0 0 0 0 0 0 0 0 Figure 13-5. RTC Modulo Register (RTCMOD) Table 13-5. RTCMOD Field Descriptions Field Description 7:0 RTC Modulo. These eight read/write bits contain the modulo value used to reset the count to 0x00 upon a compare RTCMOD match and set the RTIF status bit. A value of 0x00 sets the RTIF bit on each rising edge of the prescaler output. Writing to RTCMOD resets the prescaler and the RTCCNT counters to 0x00. Reset sets the modulo to 0x00. 13.4 Functional Description The RTC is composed of a main 8-bit up-counter with an 8-bit modulo register, a clock source selector, and a prescaler block with binary-based and decimal-based selectable values. The module also contains software selectable interrupt logic. After any MCU reset, the counter is stopped and reset to 0x00, the modulus register is set to 0x00, and the prescaler is off. The 1-kHz internal oscillator clock is selected as the default clock source. To start the prescaler, write any value other than zero to the prescaler select bits (RTCPS). Three clock sources are software selectable: the low power oscillator clock (LPO), the external clock (ERCLK), and the internal clock (IRCLK). The RTC clock select bits (RTCLKS) select the desired clock source. If a different value is written to RTCLKS, the prescaler and RTCCNT counters are reset to 0x00. MC9S08JM60 Series Data Sheet, Rev. 3 218 Freescale Semiconductor Real-Time Counter (S08RTCV1) RTCPS and the RTCLKS[0] bit select the desired divide-by value. If a different value is written to RTCPS, the prescaler and RTCCNT counters are reset to 0x00. Table 13-6 shows different prescaler period values. Table 13-6. Prescaler Period RTCPS 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111 1-kHz Internal Clock (RTCLKS = 00) Off 8 ms 32 ms 64 ms 128 ms 256 ms 512 ms 1.024 s 1 ms 2 ms 4 ms 10 ms 16 ms 0.1 s 0.5 s 1s 1-MHz External Clock 32-kHz Internal Clock 32-kHz Internal Clock (RTCLKS = 01) (RTCLKS = 10) (RTCLKS = 11) Off 1.024 ms 2.048 ms 4.096 ms 8.192 ms 16.4 ms 32.8 ms 65.5 ms 1 ms 2 ms 5 ms 10 ms 20 ms 50 ms 0.1 s 0.2 s Off 250 μs 1 ms 2 ms 4 ms 8 ms 16 ms 32 ms 31.25 μs 62.5 μs 125 μs 312.5 μs 0.5 ms 3.125 ms 15.625 ms 31.25 ms Off 32 ms 64 ms 128 ms 256 ms 512 ms 1.024 s 2.048 s 31.25 ms 62.5 ms 156.25 ms 312.5 ms 0.625 s 1.5625 s 3.125 s 6.25 s The RTC modulo register (RTCMOD) allows the compare value to be set to any value from 0x00 to 0xFF. When the counter is active, the counter increments at the selected rate until the count matches the modulo value. When these values match, the counter resets to 0x00 and continues counting. The real-time interrupt flag (RTIF) is set when a match occurs. The flag sets on the transition from the modulo value to 0x00. Writing to RTCMOD resets the prescaler and the RTCCNT counters to 0x00. The RTC allows for an interrupt to be generated when RTIF is set. To enable the real-time interrupt, set the real-time interrupt enable bit (RTIE) in RTCSC. RTIF is cleared by writing a 1 to RTIF. 13.4.1 RTC Operation Example This section shows an example of the RTC operation as the counter reaches a matching value from the modulo register. MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 219 Real-Time Counter (S08RTCV1) Internal 1-kHz Clock Source RTC Clock (RTCPS = 0xA) RTCCNT 0x52 0x53 0x54 0x55 0x00 0x01 RTIF RTCMOD 0x55 Figure 13-6. RTC Counter Overflow Example In the example of Figure 13-6, the selected clock source is the 1-kHz internal oscillator clock source. The prescaler (RTCPS) is set to 0xA or divide-by-4. The modulo value in the RTCMOD register is set to 0x55. When the counter, RTCCNT, reaches the modulo value of 0x55, the counter overflows to 0x00 and continues counting. The real-time interrupt flag, RTIF, sets when the counter value changes from 0x55 to 0x00. A real-time interrupt is generated when RTIF is set, if RTIE is set. 13.5 Initialization/Application Information This section provides example code to give some basic direction to a user on how to initialize and configure the RTC module. The example software is implemented in C language. The example below shows how to implement time of day with the RTC using the 1-kHz clock source to achieve the lowest possible power consumption. Because the 1-kHz clock source is not as accurate as a crystal, software can be added for any adjustments. For accuracy without adjustments at the expense of additional power consumption, the external clock (ERCLK) or the internal clock (IRCLK) can be selected with appropriate prescaler and modulo values. /* Initialize the elapsed time counters */ Seconds = 0; Minutes = 0; Hours = 0; Days=0; /* Configure RTC to interrupt every 1 second from 1-kHz clock source */ RTCMOD.byte = 0x00; RTCSC.byte = 0x1F; /********************************************************************** Function Name : RTC_ISR Notes : Interrupt service routine for RTC module. **********************************************************************/ #pragma TRAP_PROC void RTC_ISR(void) { /* Clear the interrupt flag */ MC9S08JM60 Series Data Sheet, Rev. 3 220 Freescale Semiconductor Real-Time Counter (S08RTCV1) RTCSC.byte = RTCSC.byte | 0x80; /* RTC interrupts every 1 Second */ Seconds++; /* 60 seconds in a minute */ if (Seconds > 59){ Minutes++; Seconds = 0; } /* 60 minutes in an hour */ if (Minutes > 59){ Hours++; Minutes = 0; } /* 24 hours in a day */ if (Hours > 23){ Days ++; Hours = 0; } MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 221 Real-Time Counter (S08RTCV1) MC9S08JM60 Series Data Sheet, Rev. 3 222 Freescale Semiconductor Chapter 14 Serial Communications Interface (S08SCIV4) 14.1 Introduction The MC9S08JM60 series include two independent serial communications interface (SCI) modules which are sometimes called universal asynchronous receiver/transmitters (UARTs). Typically, these systems are used to connect to the RS232 serial input/output (I/O) port of a personal computer or workstation, but they can also be used to communicate with other embedded controllers. A flexible, 13-bit, modulo-based baud rate generator supports a broad range of standard baud rates beyond 115.2 kbaud. Transmit and receive within the same SCI use a common baud rate, and each SCI module has a separate baud rate generator. This SCI system offers many advanced features not commonly found on other asynchronous serial I/O peripherals on other embedded controllers. The receiver employs an advanced data sampling technique that ensures reliable communication and noise detection. Hardware parity, receiver wakeup, and double buffering on transmit and receive are also included. NOTE MC9S08JM60 series devices operate at a higher voltage range (2.7 V to 5.5 V) and do not include stop1 mode. Therefore, please disregard references to stop1. MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 223 Chapter 14 Serial Communications Interface (S08SCIV4) USBDP USBDN PORT A 6 PTA5– PTA0 PTB7/ADP7 PTB6/ADP6 PTB5/KBIP5/ADP5 PTB4/KBIP4/ADP4 PTB3/SS2/ADP3 PTB2/SPSCK2/ADP2 PTB1/MOSI2/ADP1 PTB0/MISO2/ADP0 PTC6 PTC5/RxD2 PTC4 PTC3/TxD2 PTC2 PTC1/SDA PTC0/SCL HCS08 CORE ON-CHIP ICE AND DEBUG MODULE (DBG) FULL SPEED USB USB ENDPOINT TRANSCEIVER RAM 8-/16-BIT SERIAL PERIPHERAL INTERFACE MODULE (SPI2) SS2 SPSCK2 MOSI2 MISO2 RxD2 TxD2 SDA SCL USB SIE BKGD/MS BDC CPU RESET HCS08 SYSTEM CONTROL RESETS AND INTERRUPTS MODES OF OPERATION POWER MANAGEMENT IRQ/TPMCLK SERIAL COMMUNICATIONS INTERFACE MODULE (SCI2) COP IRQ LVD IIC MODULE (IIC) VDDAD VSSAD VREFL VREFH USER Flash (IN BYTES) MC9S08JM60 = 60,912 MC9S08JM32 = 32,768 12-CHANNEL, 12-BIT ANALOG-TO-DIGITAL CONVERTER (ADC) 8 4 PORT D PORT C PORT B ACMP– ANALOG COMPARATOR (ACMP) ACMP+ ACMPO SS1 SPSCK1 MOSI1 MISO1 6-CHANNEL TIMER/PWM MODULE (TPM1) SERIAL COMMUNICATIONS INTERFACE MODULE (SCI1) PORT E TPMCLK TPM1CH1 TPM1CH0 TPM1CHx 4 RxD1 TxD1 TPMCLK TPM2CH1 TPM2CH0 KBIPx 8-BIT KEYBOARD INTERRUPT MODULE (KBI) KBIPx EXTAL XTAL PTD7 PTD6 PTD5 PTD4/ADP11 PTD3/KBIP3/ADP10 PTD2/KBIP2/ACMPO PTD1/ADP9/ACMP– PTD0/ADP8/ACMP+ PTE7/SS1 PTE6/SPSCK1 PTE5/MOSI1 PTE4/MISO1 PTE3/TPM1CH1 PTE2/TPM1CH0 PTE1/RxD1 PTE0/TxD1 PTF7 PTF6 PTF5/TPM2CH1 PTF4/TPM2CH0 PTF3/TPM1CH5 PTF2/TPM1CH4 PTF1/TPM1CH3 PTF0/TPM1CH2 PTG5/EXTAL PTG4/XTAL PTG3/KBIP7 PTG2/KBIP6 PTG1/KBIP1 PTG0/KBIP0 USER RAM (IN BYTES) MC9S08JM60 = 4096 MC9S08JM32 = 2048 8-/16-BIT SERIAL PERIPHERAL INTERFACE MODULE (SPI1) MULTI-PURPOSE CLOCK GENERATOR (MCG) VSSOSC LOW-POWER OSCILLATOR SYSTEM VOLTAGE REGULATOR USB 3.3-V VOLTAGE REGULATOR REAL-TIME COUNTER (RTC) VDD VSS MODULE (TPM2) VUSB33 4 4 NOTES: 1. Port pins are software configurable with pullup device if input port. 2. Pin contains software configurable pullup/pull-down device if IRQ is enabled (IRQPE = 1). Pull-down is enabled if rising edge detect is selected (IRQEDG = 1) 3. IRQ does not have a clamp diode to VDD. IRQ must not be driven above VDD. 4. Pin contains integrated pullup device. 5. When pin functions as KBI (KBIPEn = 1) and associated pin is configured to enable the pullup device, KBEDGn can be used to reconfigure the pullup as a pull-down device. Figure 14-1. MC9S08JM60 Series Block Diagram Highlighting the SCI Blocks and Pins MC9S08JM60 Series Data Sheet, Rev. 3 224 Freescale Semiconductor PORT G PORT F 2-CHANNEL TIMER/PWM Serial Communications Interface (S08SCIV4) 14.1.1 Features Features of SCI module include: • Full-duplex, standard non-return-to-zero (NRZ) format • Double-buffered transmitter and receiver with separate enables • Programmable baud rates (13-bit modulo divider) • Interrupt-driven or polled operation: — Transmit data register empty and transmission complete — Receive data register full — Receive overrun, parity error, framing error, and noise error — Idle receiver detect — Active edge on receive pin — Break detect supporting LIN • Hardware parity generation and checking • Programmable 8-bit or 9-bit character length • Receiver wakeup by idle-line or address-mark • Optional 13-bit break character generation / 11-bit break character detection • Selectable transmitter output polarity 14.1.2 Modes of Operation See Section 14.3, “Functional Description,” For details concerning SCI operation in these modes: • 8- and 9-bit data modes • Stop mode operation • Loop mode • Single-wire mode MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 225 Serial Communications Interface (S08SCIV4) 14.1.3 Block Diagram INTERNAL BUS (WRITE-ONLY) LOOPS SCID – Tx BUFFER RSRC LOOP CONTROL Figure 14-2 shows the transmitter portion of the SCI. START STOP M 11-BIT TRANSMIT SHIFT REGISTER TO RECEIVE DATA IN TO TxD PIN SHIFT DIRECTION LSB 1 × BAUD RATE CLOCK H 8 7 6 5 4 3 2 1 0 L TXINV PREAMBLE (ALL 1s) LOAD FROM SCIxD T8 PE PT TE SBK TXDIR BRK13 PARITY GENERATION BREAK (ALL 0s) SCI CONTROLS TxD SHIFT ENABLE TRANSMIT CONTROL TxD DIRECTION TO TxD PIN LOGIC TDRE TIE TC TCIE Tx INTERRUPT REQUEST Figure 14-2. SCI Transmitter Block Diagram MC9S08JM60 Series Data Sheet, Rev. 3 226 Freescale Semiconductor Serial Communications Interface (S08SCIV4) Figure 14-3 shows the receiver portion of the SCI. INTERNAL BUS (READ-ONLY) 16 × BAUD RATE CLOCK FROM TRANSMITTER SINGLE-WIRE LOOP CONTROL LSB 8 7 6 5 4 3 2 1 0 SHIFT DIRECTION RWU RWUID RDRF RIE IDLE ILIE LBKDIF LBKDIE RXEDGIF RXEDGIE OR ORIE FE FEIE NF NEIE PE PT PARITY CHECKING PF PEIE ERROR INTERRUPT REQUEST Rx INTERRUPT REQUEST M LBKDE ALL 1s DATA RECOVERY MSB STOP LOOPS RSRC FROM RxD PIN RXINV START L 11-BIT RECEIVE SHIFT REGISTER DIVIDE BY 16 SCID – Rx BUFFER H WAKE ILT ACTIVE EDGE DETECT WAKEUP LOGIC Figure 14-3. SCI Receiver Block Diagram MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 227 Serial Communications Interface (S08SCIV4) 14.2 Register Definition The SCI has eight 8-bit registers to control baud rate, select SCI options, report SCI status, and for transmit/receive data. Refer to the direct-page register summary in the Memory chapter of this data sheet for the absolute address assignments for all SCI registers. This section refers to registers and control bits only by their names. A Freescale-provided equate or header file is used to translate these names into the appropriate absolute addresses. 14.2.1 SCI Baud Rate Registers (SCIxBDH, SCIxBDL) This pair of registers controls the prescale divisor for SCI baud rate generation. To update the 13-bit baud rate setting [SBR12:SBR0], first write to SCIxBDH to buffer the high half of the new value and then write to SCIxBDL. The working value in SCIxBDH does not change until SCIxBDL is written. SCIxBDL is reset to a non-zero value, so after reset the baud rate generator remains disabled until the first time the receiver or transmitter is enabled (RE or TE bits in SCIxC2 are written to 1). 7 6 5 4 3 2 1 0 R LBKDIE W Reset 0 0 RXEDGIE 0 SBR12 0 0 SBR11 0 SBR10 0 SBR9 0 SBR8 0 = Unimplemented or Reserved Figure 14-4. SCI Baud Rate Register (SCIxBDH) Table 14-1. SCIxBDH Field Descriptions Field 7 LBKDIE 6 RXEDGIE 4:0 SBR[12:8] Description LIN Break Detect Interrupt Enable (for LBKDIF) 0 Hardware interrupts from LBKDIF disabled (use polling). 1 Hardware interrupt requested when LBKDIF flag is 1. RxD Input Active Edge Interrupt Enable (for RXEDGIF) 0 Hardware interrupts from RXEDGIF disabled (use polling). 1 Hardware interrupt requested when RXEDGIF flag is 1. Baud Rate Modulo Divisor — The 13 bits in SBR[12:0] are referred to collectively as BR, and they set the modulo divide rate for the SCI baud rate generator. When BR = 0, the SCI baud rate generator is disabled to reduce supply current. When BR = 1 to 8191, the SCI baud rate = BUSCLK/(16×BR). See also BR bits in Table 14-2. MC9S08JM60 Series Data Sheet, Rev. 3 228 Freescale Semiconductor Serial Communications Interface (S08SCIV4) 7 6 5 4 3 2 1 0 R SBR7 W Reset 0 0 0 0 0 1 0 0 SBR6 SBR5 SBR4 SBR3 SBR2 SBR1 SBR0 Figure 14-5. SCI Baud Rate Register (SCIxBDL) Table 14-2. SCIxBDL Field Descriptions Field 7:0 SBR[7:0] Description Baud Rate Modulo Divisor — These 13 bits in SBR[12:0] are referred to collectively as BR, and they set the modulo divide rate for the SCI baud rate generator. When BR = 0, the SCI baud rate generator is disabled to reduce supply current. When BR = 1 to 8191, the SCI baud rate = BUSCLK/(16×BR). See also BR bits in Table 14-1. 14.2.2 SCI Control Register 1 (SCIxC1) This read/write register is used to control various optional features of the SCI system. 7 6 5 4 3 2 1 0 R LOOPS W Reset 0 0 0 0 0 0 0 0 SCISWAI RSRC M WAKE ILT PE PT Figure 14-6. SCI Control Register 1 (SCIxC1) Table 14-3. SCIxC1 Field Descriptions Field 7 LOOPS Description Loop Mode Select — Selects between loop back modes and normal 2-pin full-duplex modes. When LOOPS = 1, the transmitter output is internally connected to the receiver input. 0 Normal operation — RxD and TxD use separate pins. 1 Loop mode or single-wire mode where transmitter outputs are internally connected to receiver input. (See RSRC bit.) RxD pin is not used by SCI. SCI Stops in Wait Mode 0 SCI clocks continue to run in wait mode so the SCI can be the source of an interrupt that wakes up the CPU. 1 SCI clocks freeze while CPU is in wait mode. Receiver Source Select — This bit has no meaning or effect unless the LOOPS bit is set to 1. When LOOPS = 1, the receiver input is internally connected to the TxD pin and RSRC determines whether this connection is also connected to the transmitter output. 0 Provided LOOPS = 1, RSRC = 0 selects internal loop back mode and the SCI does not use the RxD pins. 1 Single-wire SCI mode where the TxD pin is connected to the transmitter output and receiver input. 9-Bit or 8-Bit Mode Select 0 Normal — start + 8 data bits (LSB first) + stop. 1 Receiver and transmitter use 9-bit data characters start + 8 data bits (LSB first) + 9th data bit + stop. 6 SCISWAI 5 RSRC 4 M MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 229 Serial Communications Interface (S08SCIV4) Table 14-3. SCIxC1 Field Descriptions (continued) Field 3 WAKE Description Receiver Wakeup Method Select — Refer to Section 14.3.3.2, “Receiver Wakeup Operation” for more information. 0 Idle-line wakeup. 1 Address-mark wakeup. Idle Line Type Select — Setting this bit to 1 ensures that the stop bit and logic 1 bits at the end of a character do not count toward the 10 or 11 bit times of logic high level needed by the idle line detection logic. Refer to Section 14.3.3.2.1, “Idle-Line Wakeup” for more information. 0 Idle character bit count starts after start bit. 1 Idle character bit count starts after stop bit. Parity Enable — Enables hardware parity generation and checking. When parity is enabled, the most significant bit (MSB) of the data character (eighth or ninth data bit) is treated as the parity bit. 0 No hardware parity generation or checking. 1 Parity enabled. Parity Type — Provided parity is enabled (PE = 1), this bit selects even or odd parity. Odd parity means the total number of 1s in the data character, including the parity bit, is odd. Even parity means the total number of 1s in the data character, including the parity bit, is even. 0 Even parity. 1 Odd parity. 2 ILT 1 PE 0 PT 14.2.3 SCI Control Register 2 (SCIxC2) This register can be read or written at any time. 7 6 5 4 3 2 1 0 R TIE W Reset 0 0 0 0 0 0 0 0 TCIE RIE ILIE TE RE RWU SBK Figure 14-7. SCI Control Register 2 (SCIxC2) Table 14-4. SCIxC2 Field Descriptions Field 7 TIE 6 TCIE 5 RIE 4 ILIE Description Transmit Interrupt Enable (for TDRE) 0 Hardware interrupts from TDRE disabled (use polling). 1 Hardware interrupt requested when TDRE flag is 1. Transmission Complete Interrupt Enable (for TC) 0 Hardware interrupts from TC disabled (use polling). 1 Hardware interrupt requested when TC flag is 1. Receiver Interrupt Enable (for RDRF) 0 Hardware interrupts from RDRF disabled (use polling). 1 Hardware interrupt requested when RDRF flag is 1. Idle Line Interrupt Enable (for IDLE) 0 Hardware interrupts from IDLE disabled (use polling). 1 Hardware interrupt requested when IDLE flag is 1. MC9S08JM60 Series Data Sheet, Rev. 3 230 Freescale Semiconductor Serial Communications Interface (S08SCIV4) Table 14-4. SCIxC2 Field Descriptions (continued) Field 3 TE Description Transmitter Enable 0 Transmitter off. 1 Transmitter on. TE must be 1 in order to use the SCI transmitter. When TE = 1, the SCI forces the TxD pin to act as an output for the SCI system. When the SCI is configured for single-wire operation (LOOPS = RSRC = 1), TXDIR controls the direction of traffic on the single SCI communication line (TxD pin). TE also can be used to queue an idle character by writing TE = 0 then TE = 1 while a transmission is in progress. Refer to Section 14.3.2.1, “Send Break and Queued Idle” for more details. When TE is written to 0, the transmitter keeps control of the port TxD pin until any data, queued idle, or queued break character finishes transmitting before allowing the pin to revert to a general-purpose I/O pin. Receiver Enable — When the SCI receiver is off, the RxD pin reverts to being a general-purpose port I/O pin. If LOOPS = 1 the RxD pin reverts to being a general-purpose I/O pin even if RE = 1. 0 Receiver off. 1 Receiver on. Receiver Wakeup Control — This bit can be written to 1 to place the SCI receiver in a standby state where it waits for automatic hardware detection of a selected wakeup condition. The wakeup condition is either an idle line between messages (WAKE = 0, idle-line wakeup), or a logic 1 in the most significant data bit in a character (WAKE = 1, address-mark wakeup). Application software sets RWU and (normally) a selected hardware condition automatically clears RWU. Refer to Section 14.3.3.2, “Receiver Wakeup Operation” for more details. 0 Normal SCI receiver operation. 1 SCI receiver in standby waiting for wakeup condition. Send Break — Writing a 1 and then a 0 to SBK queues a break character in the transmit data stream. Additional break characters of 10 or 11 (13 or 14 if BRK13 = 1) bit times of logic 0 are queued as long as SBK = 1. Depending on the timing of the set and clear of SBK relative to the information currently being transmitted, a second break character may be queued before software clears SBK. Refer to Section 14.3.2.1, “Send Break and Queued Idle” for more details. 0 Normal transmitter operation. 1 Queue break character(s) to be sent. 2 RE 1 RWU 0 SBK 14.2.4 SCI Status Register 1 (SCIxS1) This register has eight read-only status flags. Writes have no effect. Special software sequences (which do not involve writing to this register) are used to clear these status flags. 7 6 5 4 3 2 1 0 R W Reset TDRE TC RDRF IDLE OR NF FE PF 1 1 0 0 0 0 0 0 = Unimplemented or Reserved Figure 14-8. SCI Status Register 1 (SCIxS1) MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 231 Serial Communications Interface (S08SCIV4) Table 14-5. SCIxS1 Field Descriptions Field 7 TDRE Description Transmit Data Register Empty Flag — TDRE is set out of reset and when a transmit data value transfers from the transmit data buffer to the transmit shifter, leaving room for a new character in the buffer. To clear TDRE, read SCIxS1 with TDRE = 1 and then write to the SCI data register (SCIxD). 0 Transmit data register (buffer) full. 1 Transmit data register (buffer) empty. Transmission Complete Flag — TC is set out of reset and when TDRE = 1 and no data, preamble, or break character is being transmitted. 0 Transmitter active (sending data, a preamble, or a break). 1 Transmitter idle (transmission activity complete). TC is cleared automatically by reading SCIxS1 with TC = 1 and then doing one of the following three things: • Write to the SCI data register (SCIxD) to transmit new data • Queue a preamble by changing TE from 0 to 1 • Queue a break character by writing 1 to SBK in SCIxC2 Receive Data Register Full Flag — RDRF becomes set when a character transfers from the receive shifter into the receive data register (SCIxD). To clear RDRF, read SCIxS1 with RDRF = 1 and then read the SCI data register (SCIxD). 0 Receive data register empty. 1 Receive data register full. Idle Line Flag — IDLE is set when the SCI receive line becomes idle for a full character time after a period of activity. When ILT = 0, the receiver starts counting idle bit times after the start bit. So if the receive character is all 1s, these bit times and the stop bit time count toward the full character time of logic high (10 or 11 bit times depending on the M control bit) needed for the receiver to detect an idle line. When ILT = 1, the receiver doesn’t start counting idle bit times until after the stop bit. So the stop bit and any logic high bit times at the end of the previous character do not count toward the full character time of logic high needed for the receiver to detect an idle line. To clear IDLE, read SCIxS1 with IDLE = 1 and then read the SCI data register (SCIxD). After IDLE has been cleared, it cannot become set again until after a new character has been received and RDRF has been set. IDLE will get set only once even if the receive line remains idle for an extended period. 0 No idle line detected. 1 Idle line was detected. Receiver Overrun Flag — OR is set when a new serial character is ready to be transferred to the receive data register (buffer), but the previously received character has not been read from SCIxD yet. In this case, the new character (and all associated error information) is lost because there is no room to move it into SCIxD. To clear OR, read SCIxS1 with OR = 1 and then read the SCI data register (SCIxD). 0 No overrun. 1 Receive overrun (new SCI data lost). Noise Flag — The advanced sampling technique used in the receiver takes seven samples during the start bit and three samples in each data bit and the stop bit. If any of these samples disagrees with the rest of the samples within any bit time in the frame, the flag NF will be set at the same time as the flag RDRF gets set for the character. To clear NF, read SCIxS1 and then read the SCI data register (SCIxD). 0 No noise detected. 1 Noise detected in the received character in SCIxD. 6 TC 5 RDRF 4 IDLE 3 OR 2 NF MC9S08JM60 Series Data Sheet, Rev. 3 232 Freescale Semiconductor Serial Communications Interface (S08SCIV4) Table 14-5. SCIxS1 Field Descriptions (continued) Field 1 FE Description Framing Error Flag — FE is set at the same time as RDRF when the receiver detects a logic 0 where the stop bit was expected. This suggests the receiver was not properly aligned to a character frame. To clear FE, read SCIxS1 with FE = 1 and then read the SCI data register (SCIxD). 0 No framing error detected. This does not guarantee the framing is correct. 1 Framing error. Parity Error Flag — PF is set at the same time as RDRF when parity is enabled (PE = 1) and the parity bit in the received character does not agree with the expected parity value. To clear PF, read SCIxS1 and then read the SCI data register (SCIxD). 0 No parity error. 1 Parity error. 0 PF 14.2.5 SCI Status Register 2 (SCIxS2) This register has one read-only status flag. 7 6 5 4 3 2 1 0 R LBKDIF W Reset 0 0 RXEDGIF 0 RXINV 0 0 RWUID 0 BRK13 0 LBKDE 0 RAF 0 = Unimplemented or Reserved Figure 14-9. SCI Status Register 2 (SCIxS2) Table 14-6. SCIxS2 Field Descriptions Field 7 LBKDIF Description LIN Break Detect Interrupt Flag — LBKDIF is set when the LIN break detect circuitry is enabled and a LIN break character is detected. LBKDIF is cleared by writing a “1” to it. 0 No LIN break character has been detected. 1 LIN break character has been detected. RxD Pin Active Edge Interrupt Flag — RXEDGIF is set when an active edge (falling if RXINV = 0, rising if RXINV=1) on the RxD pin occurs. RXEDGIF is cleared by writing a “1” to it. 0 No active edge on the receive pin has occurred. 1 An active edge on the receive pin has occurred. Receive Data Inversion — Setting this bit reverses the polarity of the received data input. 0 Receive data not inverted 1 Receive data inverted Receive Wake Up Idle Detect— RWUID controls whether the idle character that wakes up the receiver sets the IDLE bit. 0 During receive standby state (RWU = 1), the IDLE bit does not get set upon detection of an idle character. 1 During receive standby state (RWU = 1), the IDLE bit gets set upon detection of an idle character. Break Character Generation Length — BRK13 is used to select a longer transmitted break character length. Detection of a framing error is not affected by the state of this bit. 0 Break character is transmitted with length of 10 bit times (11 if M = 1) 1 Break character is transmitted with length of 13 bit times (14 if M = 1) 6 RXEDGIF 4 RXINV1 3 RWUID 2 BRK13 MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 233 Serial Communications Interface (S08SCIV4) Table 14-6. SCIxS2 Field Descriptions (continued) Field 1 LBKDE Description LIN Break Detection Enable— LBKDE is used to select a longer break character detection length. While LBKDE is set, framing error (FE) and receive data register full (RDRF) flags are prevented from setting. 0 Break character is detected at length of 10 bit times (11 if M = 1). 1 Break character is detected at length of 11 bit times (12 if M = 1). Receiver Active Flag — RAF is set when the SCI receiver detects the beginning of a valid start bit, and RAF is cleared automatically when the receiver detects an idle line. This status flag can be used to check whether an SCI character is being received before instructing the MCU to go to stop mode. 0 SCI receiver idle waiting for a start bit. 1 SCI receiver active (RxD input not idle). 0 RAF 1 Setting RXINV inverts the RxD input for all cases: data bits, start and stop bits, break, and idle. When using an internal oscillator in a LIN system, it is necessary to raise the break detection threshold by one bit time. Under the worst case timing conditions allowed in LIN, it is possible that a 0x00 data character can appear to be 10.26 bit times long at a slave which is running 14% faster than the master. This would trigger normal break detection circuitry which is designed to detect a 10 bit break symbol. When the LBKDE bit is set, framing errors are inhibited and the break detection threshold changes from 10 bits to 11 bits, preventing false detection of a 0x00 data character as a LIN break symbol. 14.2.6 SCI Control Register 3 (SCIxC3) 7 6 5 4 3 2 1 0 R W Reset R8 T8 0 0 TXDIR 0 TXINV 0 ORIE 0 NEIE 0 FEIE 0 PEIE 0 = Unimplemented or Reserved Figure 14-10. SCI Control Register 3 (SCIxC3) Table 14-7. SCIxC3 Field Descriptions Field 7 R8 Description Ninth Data Bit for Receiver — When the SCI is configured for 9-bit data (M = 1), R8 can be thought of as a ninth receive data bit to the left of the MSB of the buffered data in the SCIxD register. When reading 9-bit data, read R8 before reading SCIxD because reading SCIxD completes automatic flag clearing sequences which could allow R8 and SCIxD to be overwritten with new data. Ninth Data Bit for Transmitter — When the SCI is configured for 9-bit data (M = 1), T8 may be thought of as a ninth transmit data bit to the left of the MSB of the data in the SCIxD register. When writing 9-bit data, the entire 9-bit value is transferred to the SCI shift register after SCIxD is written so T8 should be written (if it needs to change from its previous value) before SCIxD is written. If T8 does not need to change in the new value (such as when it is used to generate mark or space parity), it need not be written each time SCIxD is written. TxD Pin Direction in Single-Wire Mode — When the SCI is configured for single-wire half-duplex operation (LOOPS = RSRC = 1), this bit determines the direction of data at the TxD pin. 0 TxD pin is an input in single-wire mode. 1 TxD pin is an output in single-wire mode. 6 T8 5 TXDIR MC9S08JM60 Series Data Sheet, Rev. 3 234 Freescale Semiconductor Serial Communications Interface (S08SCIV4) Table 14-7. SCIxC3 Field Descriptions (continued) Field 4 TXINV1 3 ORIE 2 NEIE 1 FEIE Description Transmit Data Inversion — Setting this bit reverses the polarity of the transmitted data output. 0 Transmit data not inverted 1 Transmit data inverted Overrun Interrupt Enable — This bit enables the overrun flag (OR) to generate hardware interrupt requests. 0 OR interrupts disabled (use polling). 1 Hardware interrupt requested when OR = 1. Noise Error Interrupt Enable — This bit enables the noise flag (NF) to generate hardware interrupt requests. 0 NF interrupts disabled (use polling). 1 Hardware interrupt requested when NF = 1. Framing Error Interrupt Enable — This bit enables the framing error flag (FE) to generate hardware interrupt requests. 0 FE interrupts disabled (use polling). 1 Hardware interrupt requested when FE = 1. Parity Error Interrupt Enable — This bit enables the parity error flag (PF) to generate hardware interrupt requests. 0 PF interrupts disabled (use polling). 1 Hardware interrupt requested when PF = 1. 0 PEIE 1 Setting TXINV inverts the TxD output for all cases: data bits, start and stop bits, break, and idle. 14.2.7 SCI Data Register (SCIxD) This register is actually two separate registers. Reads return the contents of the read-only receive data buffer and writes go to the write-only transmit data buffer. Reads and writes of this register are also involved in the automatic flag clearing mechanisms for the SCI status flags. 7 6 5 4 3 2 1 0 R W Reset R7 T7 0 R6 T6 0 R5 T5 0 R4 T4 0 R3 T3 0 R2 T2 0 R1 T1 0 R0 T0 0 Figure 14-11. SCI Data Register (SCIxD) 14.3 Functional Description The SCI allows full-duplex, asynchronous, NRZ serial communication among the MCU and remote devices, including other MCUs. The SCI comprises a baud rate generator, transmitter, and receiver block. The transmitter and receiver operate independently, although they use the same baud rate generator. During normal operation, the MCU monitors the status of the SCI, writes the data to be transmitted, and processes received data. The following describes each of the blocks of the SCI. 14.3.1 Baud Rate Generation As shown in Figure 14-12, the clock source for the SCI baud rate generator is the bus-rate clock. MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 235 Serial Communications Interface (S08SCIV4) MODULO DIVIDE BY (1 THROUGH 8191) DIVIDE BY 16 Tx BAUD RATE BUSCLK SBR12:SBR0 BAUD RATE GENERATOR OFF IF [SBR12:SBR0] = 0 Rx SAMPLING CLOCK (16 × BAUD RATE) BAUD RATE = BUSCLK [SBR12:SBR0] × 16 Figure 14-12. SCI Baud Rate Generation SCI communications require the transmitter and receiver (which typically derive baud rates from independent clock sources) to use the same baud rate. Allowed tolerance on this baud frequency depends on the details of how the receiver synchronizes to the leading edge of the start bit and how bit sampling is performed. The MCU resynchronizes to bit boundaries on every high-to-low transition, but in the worst case, there are no such transitions in the full 10- or 11-bit time character frame so any mismatch in baud rate is accumulated for the whole character time. For a Freescale Semiconductor SCI system whose bus frequency is driven by a crystal, the allowed baud rate mismatch is about ±4.5 percent for 8-bit data format and about ±4 percent for 9-bit data format. Although baud rate modulo divider settings do not always produce baud rates that exactly match standard rates, it is normally possible to get within a few percent, which is acceptable for reliable communications. 14.3.2 Transmitter Functional Description This section describes the overall block diagram for the SCI transmitter, as well as specialized functions for sending break and idle characters. The transmitter block diagram is shown in Figure 14-2. The transmitter output (TxD) idle state defaults to logic high (TXINV = 0 following reset). The transmitter output is inverted by setting TXINV = 1. The transmitter is enabled by setting the TE bit in SCIxC2. This queues a preamble character that is one full character frame of the idle state. The transmitter then remains idle until data is available in the transmit data buffer. Programs store data into the transmit data buffer by writing to the SCI data register (SCIxD). The central element of the SCI transmitter is the transmit shift register that is either 10 or 11 bits long depending on the setting in the M control bit. For the remainder of this section, we will assume M = 0, selecting the normal 8-bit data mode. In 8-bit data mode, the shift register holds a start bit, eight data bits, and a stop bit. When the transmit shift register is available for a new SCI character, the value waiting in the transmit data register is transferred to the shift register (synchronized with the baud rate clock) and the transmit data register empty (TDRE) status flag is set to indicate another character may be written to the transmit data buffer at SCIxD. If no new character is waiting in the transmit data buffer after a stop bit is shifted out the TxD pin, the transmitter sets the transmit complete flag and enters an idle mode, with TxD high, waiting for more characters to transmit. MC9S08JM60 Series Data Sheet, Rev. 3 236 Freescale Semiconductor Serial Communications Interface (S08SCIV4) Writing 0 to TE does not immediately release the pin to be a general-purpose I/O pin. Any transmit activity that is in progress must first be completed. This includes data characters in progress, queued idle characters, and queued break characters. 14.3.2.1 Send Break and Queued Idle The SBK control bit in SCIxC2 is used to send break characters which were originally used to gain the attention of old teletype receivers. Break characters are a full character time of logic 0 (10 bit times including the start and stop bits). A longer break of 13 bit times can be enabled by setting BRK13 = 1. Normally, a program would wait for TDRE to become set to indicate the last character of a message has moved to the transmit shifter, then write 1 and then write 0 to the SBK bit. This action queues a break character to be sent as soon as the shifter is available. If SBK is still 1 when the queued break moves into the shifter (synchronized to the baud rate clock), an additional break character is queued. If the receiving device is another Freescale Semiconductor SCI, the break characters will be received as 0s in all eight data bits and a framing error (FE = 1) occurs. When idle-line wakeup is used, a full character time of idle (logic 1) is needed between messages to wake up any sleeping receivers. Normally, a program would wait for TDRE to become set to indicate the last character of a message has moved to the transmit shifter, then write 0 and then write 1 to the TE bit. This action queues an idle character to be sent as soon as the shifter is available. As long as the character in the shifter does not finish while TE = 0, the SCI transmitter never actually releases control of the TxD pin. If there is a possibility of the shifter finishing while TE = 0, set the general-purpose I/O controls so the pin that is shared with TxD is an output driving a logic 1. This ensures that the TxD line will look like a normal idle line even if the SCI loses control of the port pin between writing 0 and then 1 to TE. The length of the break character is affected by the BRK13 and M bits as shown below. Table 14-8. Break Character Length BRK13 0 0 1 1 M 0 1 0 1 Break Character Length 10 bit times 11 bit times 13 bit times 14 bit times 14.3.3 Receiver Functional Description In this section, the receiver block diagram (Figure 14-3) is used as a guide for the overall receiver functional description. Next, the data sampling technique used to reconstruct receiver data is described in more detail. Finally, two variations of the receiver wakeup function are explained. The receiver input is inverted by setting RXINV = 1. The receiver is enabled by setting the RE bit in SCIxC2. Character frames consist of a start bit of logic 0, eight (or nine) data bits (LSB first), and a stop bit of logic 1. For information about 9-bit data mode, refer to Section 14.3.5.1, “8- and 9-Bit Data Modes.” For the remainder of this discussion, we assume the SCI is configured for normal 8-bit data mode. After receiving the stop bit into the receive shifter, and provided the receive data register is not already full, the data character is transferred to the receive data register and the receive data register full (RDRF) MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 237 Serial Communications Interface (S08SCIV4) status flag is set. If RDRF was already set indicating the receive data register (buffer) was already full, the overrun (OR) status flag is set and the new data is lost. Because the SCI receiver is double-buffered, the program has one full character time after RDRF is set before the data in the receive data buffer must be read to avoid a receiver overrun. When a program detects that the receive data register is full (RDRF = 1), it gets the data from the receive data register by reading SCIxD. The RDRF flag is cleared automatically by a 2-step sequence which is normally satisfied in the course of the user’s program that handles receive data. Refer to Section 14.3.4, “Interrupts and Status Flags,” for more details about flag clearing. 14.3.3.1 Data Sampling Technique The SCI receiver uses a 16× baud rate clock for sampling. The receiver starts by taking logic level samples at 16 times the baud rate to search for a falling edge on the RxD serial data input pin. A falling edge is defined as a logic 0 sample after three consecutive logic 1 samples. The 16× baud rate clock is used to divide the bit time into 16 segments labeled RT1 through RT16. When a falling edge is located, three more samples are taken at RT3, RT5, and RT7 to make sure this was a real start bit and not merely noise. If at least two of these three samples are 0, the receiver assumes it is synchronized to a receive character. The receiver then samples each bit time, including the start and stop bits, at RT8, RT9, and RT10 to determine the logic level for that bit. The logic level is interpreted to be that of the majority of the samples taken during the bit time. In the case of the start bit, the bit is assumed to be 0 if at least two of the samples at RT3, RT5, and RT7 are 0 even if one or all of the samples taken at RT8, RT9, and RT10 are 1s. If any sample in any bit time (including the start and stop bits) in a character frame fails to agree with the logic level for that bit, the noise flag (NF) will be set when the received character is transferred to the receive data buffer. The falling edge detection logic continuously looks for falling edges, and if an edge is detected, the sample clock is resynchronized to bit times. This improves the reliability of the receiver in the presence of noise or mismatched baud rates. It does not improve worst case analysis because some characters do not have any extra falling edges anywhere in the character frame. In the case of a framing error, provided the received character was not a break character, the sampling logic that searches for a falling edge is filled with three logic 1 samples so that a new start bit can be detected almost immediately. In the case of a framing error, the receiver is inhibited from receiving any new characters until the framing error flag is cleared. The receive shift register continues to function, but a complete character cannot transfer to the receive data buffer if FE is still set. 14.3.3.2 Receiver Wakeup Operation Receiver wakeup is a hardware mechanism that allows an SCI receiver to ignore the characters in a message that is intended for a different SCI receiver. In such a system, all receivers evaluate the first character(s) of each message, and as soon as they determine the message is intended for a different receiver, they write logic 1 to the receiver wake up (RWU) control bit in SCIxC2. When RWU bit is set, the status flags associated with the receiver (with the exception of the idle bit, IDLE, when RWUID bit is set) are inhibited from setting, thus eliminating the software overhead for handling the unimportant MC9S08JM60 Series Data Sheet, Rev. 3 238 Freescale Semiconductor Serial Communications Interface (S08SCIV4) message characters. At the end of a message, or at the beginning of the next message, all receivers automatically force RWU to 0 so all receivers wake up in time to look at the first character(s) of the next message. 14.3.3.2.1 Idle-Line Wakeup When WAKE = 0, the receiver is configured for idle-line wakeup. In this mode, RWU is cleared automatically when the receiver detects a full character time of the idle-line level. The M control bit selects 8-bit or 9-bit data mode that determines how many bit times of idle are needed to constitute a full character time (10 or 11 bit times because of the start and stop bits). When RWU is one and RWUID is zero, the idle condition that wakes up the receiver does not set the IDLE flag. The receiver wakes up and waits for the first data character of the next message which will set the RDRF flag and generate an interrupt if enabled. When RWUID is one, any idle condition sets the IDLE flag and generates an interrupt if enabled, regardless of whether RWU is zero or one. The idle-line type (ILT) control bit selects one of two ways to detect an idle line. When ILT = 0, the idle bit counter starts after the start bit so the stop bit and any logic 1s at the end of a character count toward the full character time of idle. When ILT = 1, the idle bit counter does not start until after a stop bit time, so the idle detection is not affected by the data in the last character of the previous message. 14.3.3.2.2 Address-Mark Wakeup When WAKE = 1, the receiver is configured for address-mark wakeup. In this mode, RWU is cleared automatically when the receiver detects a logic 1 in the most significant bit of a received character (eighth bit in M = 0 mode and ninth bit in M = 1 mode). Address-mark wakeup allows messages to contain idle characters but requires that the MSB be reserved for use in address frames. The logic 1 MSB of an address frame clears the RWU bit before the stop bit is received and sets the RDRF flag. In this case the character with the MSB set is received even though the receiver was sleeping during most of this character time. 14.3.4 Interrupts and Status Flags The SCI system has three separate interrupt vectors to reduce the amount of software needed to isolate the cause of the interrupt. One interrupt vector is associated with the transmitter for TDRE and TC events. Another interrupt vector is associated with the receiver for RDRF, IDLE, RXEDGIF and LBKDIF events, and a third vector is used for OR, NF, FE, and PF error conditions. Each of these ten interrupt sources can be separately masked by local interrupt enable masks. The flags can still be polled by software when the local masks are cleared to disable generation of hardware interrupt requests. The SCI transmitter has two status flags that optionally can generate hardware interrupt requests. Transmit data register empty (TDRE) indicates when there is room in the transmit data buffer to write another transmit character to SCIxD. If the transmit interrupt enable (TIE) bit is set, a hardware interrupt will be requested whenever TDRE = 1. Transmit complete (TC) indicates that the transmitter is finished transmitting all data, preamble, and break characters and is idle with TxD at the inactive level. This flag is often used in systems with modems to determine when it is safe to turn off the modem. If the transmit complete interrupt enable (TCIE) bit is set, a hardware interrupt will be requested whenever TC = 1. MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 239 Serial Communications Interface (S08SCIV4) Instead of hardware interrupts, software polling may be used to monitor the TDRE and TC status flags if the corresponding TIE or TCIE local interrupt masks are 0s. When a program detects that the receive data register is full (RDRF = 1), it gets the data from the receive data register by reading SCIxD. The RDRF flag is cleared by reading SCIxS1 while RDRF = 1 and then reading SCIxD. When polling is used, this sequence is naturally satisfied in the normal course of the user program. If hardware interrupts are used, SCIxS1 must be read in the interrupt service routine (ISR). Normally, this is done in the ISR anyway to check for receive errors, so the sequence is automatically satisfied. The IDLE status flag includes logic that prevents it from getting set repeatedly when the RxD line remains idle for an extended period of time. IDLE is cleared by reading SCIxS1 while IDLE = 1 and then reading SCIxD. After IDLE has been cleared, it cannot become set again until the receiver has received at least one new character and has set RDRF. If the associated error was detected in the received character that caused RDRF to be set, the error flags — noise flag (NF), framing error (FE), and parity error flag (PF) — get set at the same time as RDRF. These flags are not set in overrun cases. If RDRF was already set when a new character is ready to be transferred from the receive shifter to the receive data buffer, the overrun (OR) flag gets set instead the data along with any associated NF, FE, or PF condition is lost. At any time, an active edge on the RxD serial data input pin causes the RXEDGIF flag to set. The RXEDGIF flag is cleared by writing a “1” to it. This function does depend on the receiver being enabled (RE = 1). 14.3.5 Additional SCI Functions The following sections describe additional SCI functions. 14.3.5.1 8- and 9-Bit Data Modes The SCI system (transmitter and receiver) can be configured to operate in 9-bit data mode by setting the M control bit in SCIxC1. In 9-bit mode, there is a ninth data bit to the left of the MSB of the SCI data register. For the transmit data buffer, this bit is stored in T8 in SCIxC3. For the receiver, the ninth bit is held in R8 in SCIxC3. For coherent writes to the transmit data buffer, write to the T8 bit before writing to SCIxD. If the bit value to be transmitted as the ninth bit of a new character is the same as for the previous character, it is not necessary to write to T8 again. When data is transferred from the transmit data buffer to the transmit shifter, the value in T8 is copied at the same time data is transferred from SCIxD to the shifter. 9-bit data mode typically is used in conjunction with parity to allow eight bits of data plus the parity in the ninth bit. Or it is used with address-mark wakeup so the ninth data bit can serve as the wakeup bit. In custom protocols, the ninth bit can also serve as a software-controlled marker. MC9S08JM60 Series Data Sheet, Rev. 3 240 Freescale Semiconductor Serial Communications Interface (S08SCIV4) 14.3.5.2 Stop Mode Operation During all stop modes, clocks to the SCI module are halted. In stop1 and stop2 modes, all SCI register data is lost and must be re-initialized upon recovery from these two stop modes. No SCI module registers are affected in stop3 mode. The receive input active edge detect circuit is still active in stop3 mode, but not in stop2.. An active edge on the receive input brings the CPU out of stop3 mode if the interrupt is not masked (RXEDGIE = 1). Note, because the clocks are halted, the SCI module will resume operation upon exit from stop (only in stop3 mode). Software should ensure stop mode is not entered while there is a character being transmitted out of or received into the SCI module. 14.3.5.3 Loop Mode When LOOPS = 1, the RSRC bit in the same register chooses between loop mode (RSRC = 0) or single-wire mode (RSRC = 1). Loop mode is sometimes used to check software, independent of connections in the external system, to help isolate system problems. In this mode, the transmitter output is internally connected to the receiver input and the RxD pin is not used by the SCI, so it reverts to a general-purpose port I/O pin. 14.3.5.4 Single-Wire Operation When LOOPS = 1, the RSRC bit in the same register chooses between loop mode (RSRC = 0) or single-wire mode (RSRC = 1). Single-wire mode is used to implement a half-duplex serial connection. The receiver is internally connected to the transmitter output and to the TxD pin. The RxD pin is not used and reverts to a general-purpose port I/O pin. In single-wire mode, the TXDIR bit in SCIxC3 controls the direction of serial data on the TxD pin. When TXDIR = 0, the TxD pin is an input to the SCI receiver and the transmitter is temporarily disconnected from the TxD pin so an external device can send serial data to the receiver. When TXDIR = 1, the TxD pin is an output driven by the transmitter. In single-wire mode, the internal loop back connection from the transmitter to the receiver causes the receiver to receive characters that are sent out by the transmitter. MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 241 Serial Communications Interface (S08SCIV4) MC9S08JM60 Series Data Sheet, Rev. 3 242 Freescale Semiconductor Chapter 15 16-Bit Serial Peripheral Interface (S08SPI16V1) 15.1 Introduction The 8- or 16-bit selectable serial peripheral interface (SPI) module provides for full-duplex, synchronous, serial communication between the MCU and peripheral devices. These peripheral devices can include other microcontrollers, analog-to-digital converters, shift registers, sensors, memories, etc. The SPI runs at a baud rate up to the bus clock divided by two in master mode and up to the bus clock divided by four in slave mode. Software can poll the status flags, or SPI operation can be interrupt driven. The SPI also supports a data length of 8 or 16 bits and includes a hardware match feature for the receive data buffer. The MC9S08JM60 series have two serial peripheral interface modules (SPI1 and SPI2). The four pins associated with SPI functionality are shared with PTB[3:0] and PTE[7:4]. See Appendix A, “Electrical Characteristics,” for SPI electrical parametric information. 15.1.1 SPI Port Configuration Information By default, the input filters on the SPI port pins will be enabled (SPIxFE=1), which restricts the SPI data rate to 6 MHz, but protects the SPI from noise during data transfers.To configure the SPI at a baud rate of 6MHz or greater, the input filters on the SPI port pins must be disabled by clearing the SPIxFE in SOPT2. and also enable the high output drive strength selection on the affected SPI port pins. MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 243 Chapter 15 16-Bit Serial Peripheral Interface (S08SPI16V1) USBDP USBDN PORT A 6 PTA5– PTA0 PTB7/ADP7 PTB6/ADP6 PTB5/KBIP5/ADP5 PTB4/KBIP4/ADP4 PTB3/SS2/ADP3 PTB2/SPSCK2/ADP2 PTB1/MOSI2/ADP1 PTB0/MISO2/ADP0 PTC6 PTC5/RxD2 PTC4 PTC3/TxD2 PTC2 PTC1/SDA PTC0/SCL HCS08 CORE ON-CHIP ICE AND DEBUG MODULE (DBG) FULL SPEED USB USB ENDPOINT TRANSCEIVER RAM 8-/16-BIT SERIAL PERIPHERAL INTERFACE MODULE (SPI2) SS2 SPSCK2 MOSI2 MISO2 RxD2 TxD2 SDA SCL USB SIE BKGD/MS BDC CPU RESET HCS08 SYSTEM CONTROL RESETS AND INTERRUPTS MODES OF OPERATION POWER MANAGEMENT IRQ/TPMCLK SERIAL COMMUNICATIONS INTERFACE MODULE (SCI2) COP IRQ LVD IIC MODULE (IIC) VDDAD VSSAD VREFL VREFH USER Flash (IN BYTES) MC9S08JM60 = 60,912 MC9S08JM32 = 32,768 12-CHANNEL, 12-BIT ANALOG-TO-DIGITAL CONVERTER (ADC) 8 4 PORT D PORT C PORT B ACMP– ANALOG COMPARATOR (ACMP) ACMP+ ACMPO SS1 SPSCK1 MOSI1 MISO1 6-CHANNEL TIMER/PWM MODULE (TPM1) SERIAL COMMUNICATIONS INTERFACE MODULE (SCI1) PORT E TPMCLK TPM1CH1 TPM1CH0 TPM1CHx 4 RxD1 TxD1 TPMCLK TPM2CH1 TPM2CH0 KBIPx 8-BIT KEYBOARD INTERRUPT MODULE (KBI) KBIPx EXTAL XTAL PTD7 PTD6 PTD5 PTD4/ADP11 PTD3/KBIP3/ADP10 PTD2/KBIP2/ACMPO PTD1/ADP9/ACMP– PTD0/ADP8/ACMP+ PTE7/SS1 PTE6/SPSCK1 PTE5/MOSI1 PTE4/MISO1 PTE3/TPM1CH1 PTE2/TPM1CH0 PTE1/RxD1 PTE0/TxD1 PTF7 PTF6 PTF5/TPM2CH1 PTF4/TPM2CH0 PTF3/TPM1CH5 PTF2/TPM1CH4 PTF1/TPM1CH3 PTF0/TPM1CH2 PTG5/EXTAL PTG4/XTAL PTG3/KBIP7 PTG2/KBIP6 PTG1/KBIP1 PTG0/KBIP0 USER RAM (IN BYTES) MC9S08JM60 = 4096 MC9S08JM32 = 2048 8-/16-BIT SERIAL PERIPHERAL INTERFACE MODULE (SPI1) MULTI-PURPOSE CLOCK GENERATOR (MCG) VSSOSC LOW-POWER OSCILLATOR SYSTEM VOLTAGE REGULATOR USB 3.3-V VOLTAGE REGULATOR REAL-TIME COUNTER (RTC) VDD VSS MODULE (TPM2) VUSB33 4 4 NOTES: 1. Port pins are software configurable with pullup device if input port. 2. Pin contains software configurable pullup/pull-down device if IRQ is enabled (IRQPE = 1). Pull-down is enabled if rising edge detect is selected (IRQEDG = 1) 3. IRQ does not have a clamp diode to VDD. IRQ must not be driven above VDD. 4. Pin contains integrated pullup device. 5. When pin functions as KBI (KBIPEn = 1) and associated pin is configured to enable the pullup device, KBEDGn can be used to reconfigure the pullup as a pull-down device. Figure 15-1. MC9S08JM60 Series Block Diagram Highlighting the SPI Blocks and Pins MC9S08JM60 Series Data Sheet, Rev. 3 244 Freescale Semiconductor PORT G PORT F 2-CHANNEL TIMER/PWM Serial Peripheral Interface (S08SPI16V1) Module Initialization (Slave): Write: Write: Write: SPIxC1 SPIxC2 SPIxMH:SPIxML to configure to configure to set interrupts, set primary SPI options, slave mode select, and system enable. optional SPI features, hardware match interrupt enable, and 8- or 16-bit data transmission length hardware compare value that triggers SPMF (optional) when value in receive data buffer equals this value. Module Initialization (Master): Write: SPIxC1 to configure interrupts, set primary SPI options, master mode select, and system enable. optional SPI features, hardware match interrupt enable, and 8- or 16-bit data transmission length baud rate hardware compare value that triggers SPMF (optional) when value in receive data buffer equals this value. Module Use: After SPI master initiates transfer by checking that SPTEF = 1 and then writing data to SPIDH/L: Wait for SPRF, then read from SPIDH/L Wait for SPTEF, then write to SPIDH/L Data transmissions can be 8- or 16-bits long, and mode fault detection can be enabled for master mode in cases where more than one SPI device might become a master at the same time. Also, some applications may utilize the receive data buffer hardware match feature to trigger specific actions, such as when command data can be sent through the SPI or to indicate the end of an SPI transmission. SPIxC1 SPIE SPE SPTIE MSTR CPOL CPHA SSOE LSBFE Write: Write: SPIxC2 SPIxBR SPIxMH:SPIxML to configure to set Write: to set Module/interrupt enables and configuration SPIxC2 SPMIE SPIMODE MODFEN BIDIROE SPISWAI SPC0 Additional configuration options. SPIxBR SPPR2 SPPR1 SPPR0 SPR2 SPR1 SPR0 Baud rate = (BUSCLK/SPPR[2:0])/SPR2[2:0] SPIxDH SPIxDL Bit 15 Bit 7 Bit 14 Bit 6 Bit 13 Bit 5 Bit 12 Bit 4 Bit 11 Bit 3 Bit 10 Bit 2 Bit 9 Bit 1 Bit 8 Bit 0 SPIxMH SPIxML Bit 15 Bit 7 Bit 14 Bit 6 Bit 13 Bit 5 Bit 12 Bit 4 Bit 11 Bit 3 Bit 10 Bit 2 Bit 9 Bit 1 Bit 8 Bit 0 Hardware Match Value SPIxS SPRF SPMF SPTEF MODF Figure 15-2. SPI Module Quick Start MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 245 Serial Peripheral Interface (S08SPI16V1) 15.1.2 Features The SPI includes these distinctive features: • Master mode or slave mode operation • Full-duplex or single-wire bidirectional mode • Programmable transmit bit rate • Double-buffered transmit and receive data register • Serial clock phase and polarity options • Slave select output • Mode fault error flag with CPU interrupt capability • Control of SPI operation during wait mode • Selectable MSB-first or LSB-first shifting • Programmable 8- or 16-bit data transmission length • Receive data buffer hardware match feature 15.1.3 Modes of Operation The SPI functions in three modes, run, wait, and stop. • Run Mode This is the basic mode of operation. • Wait Mode SPI operation in wait mode is a configurable low power mode, controlled by the SPISWAI bit located in the SPIxC2 register. In wait mode, if the SPISWAI bit is clear, the SPI operates like in Run Mode. If the SPISWAI bit is set, the SPI goes into a power conservative state, with the SPI clock generation turned off. If the SPI is configured as a master, any transmission in progress stops, but is resumed after CPU goes into Run Mode. If the SPI is configured as a slave, reception and transmission of a byte continues, so that the slave stays synchronized to the master. • Stop Mode The SPI is inactive in stop3 mode for reduced power consumption. If the SPI is configured as a master, any transmission in progress stops, but is resumed after the CPU goes into Run Mode. If the SPI is configured as a slave, reception and transmission of a data continues, so that the slave stays synchronized to the master. The SPI is completely disabled in all other stop modes. When the CPU wakes from these stop modes, all SPI register content will be reset. This is a high level description only, detailed descriptions of operating modes are contained in section Section 15.4.9, “Low Power Mode Options.” 15.1.4 Block Diagrams This section includes block diagrams showing SPI system connections, the internal organization of the SPI module, and the SPI clock dividers that control the master mode bit rate. MC9S08JM60 Series Data Sheet, Rev. 3 246 Freescale Semiconductor Serial Peripheral Interface (S08SPI16V1) 15.1.4.1 SPI System Block Diagram Figure 15-3 shows the SPI modules of two MCUs connected in a master-slave arrangement. The master device initiates all SPI data transfers. During a transfer, the master shifts data out (on the MOSI pin) to the slave while simultaneously shifting data in (on the MISO pin) from the slave. The transfer effectively exchanges the data that was in the SPI shift registers of the two SPI systems. The SPSCK signal is a clock output from the master and an input to the slave. The slave device must be selected by a low level on the slave select input (SS pin). In this system, the master device has configured its SS pin as an optional slave select output. MASTER MOSI SPI SHIFTER MISO MISO MOSI SPI SHIFTER SLAVE 8 OR 16 BITS 8 OR 16 BITS SPSCK CLOCK GENERATOR SPSCK SS SS Figure 15-3. SPI System Connections 15.1.4.2 SPI Module Block Diagram Figure 15-4 is a block diagram of the SPI module. The central element of the SPI is the SPI shift register. Data is written to the double-buffered transmitter (write to SPIxDH:SPIxDL) and gets transferred to the SPI shift register at the start of a data transfer. After shifting in 8 or 16 bits (as determined by SPIMODE bit) of data, the data is transferred into the double-buffered receiver where it can be read (read from SPIxDH:SPIxDL). Pin multiplexing logic controls connections between MCU pins and the SPI module. When the SPI is configured as a master, the clock output is routed to the SPSCK pin, the shifter output is routed to MOSI, and the shifter input is routed from the MISO pin. When the SPI is configured as a slave, the SPSCK pin is routed to the clock input of the SPI, the shifter output is routed to MISO, and the shifter input is routed from the MOSI pin. In the external SPI system, simply connect all SPSCK pins to each other, all MISO pins together, and all MOSI pins together. Peripheral devices often use slightly different names for these pins. MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 247 Serial Peripheral Interface (S08SPI16V1) PIN CONTROL M SPE Tx BUFFER (WRITE SPIxDH:SPIxDL) ENABLE SPI SYSTEM SHIFT OUT SPIMODE 8 OR 16 BIT MODE SHIFT DIRECTION SPI SHIFT REGISTER SHIFT IN SPC0 BIDIROE LSBFE SHIFT CLOCK Rx BUFFER FULL Tx BUFFER EMPTY M S MISO (SISO) S MOSI (MOMI) Rx BUFFER (READ SPIxDH:SPIxDL) MASTER CLOCK BUS RATE CLOCK MSTR SPIBR CLOCK GENERATOR MASTER/SLAVE MODE SELECT MODFEN MODE FAULT DETECTION SSOE CLOCK LOGIC SLAVE CLOCK M S MASTER/ SLAVE SPSCK SS 16-BIT COMPARATOR SPIxMH:SPIxML 16-BIT LATCH SPRF SPTEF SPTIE MODF SPIE SPMF SPMIE SPI INTERRUPT REQUEST Figure 15-4. SPI Module Block Diagram 15.2 External Signal Description The SPI optionally shares four port pins. The function of these pins depends on the settings of SPI control bits. When the SPI is disabled (SPE = 0), these four pins revert to being general-purpose port I/O pins that are not controlled by the SPI. 15.2.1 SPSCK — SPI Serial Clock When the SPI is enabled as a slave, this pin is the serial clock input. When the SPI is enabled as a master, this pin is the serial clock output. MC9S08JM60 Series Data Sheet, Rev. 3 248 Freescale Semiconductor Serial Peripheral Interface (S08SPI16V1) 15.2.2 MOSI — Master Data Out, Slave Data In When the SPI is enabled as a master and SPI pin control zero (SPC0) is 0 (not bidirectional mode), this pin is the serial data output. When the SPI is enabled as a slave and SPC0 = 0, this pin is the serial data input. If SPC0 = 1 to select single-wire bidirectional mode, and master mode is selected, this pin becomes the bidirectional data I/O pin (MOMI). Also, the bidirectional mode output enable bit determines whether the pin acts as an input (BIDIROE = 0) or an output (BIDIROE = 1). If SPC0 = 1 and slave mode is selected, this pin is not used by the SPI and reverts to being a general-purpose port I/O pin. 15.2.3 MISO — Master Data In, Slave Data Out When the SPI is enabled as a master and SPI pin control zero (SPC0) is 0 (not bidirectional mode), this pin is the serial data input. When the SPI is enabled as a slave and SPC0 = 0, this pin is the serial data output. If SPC0 = 1 to select single-wire bidirectional mode, and slave mode is selected, this pin becomes the bidirectional data I/O pin (SISO) and the bidirectional mode output enable bit determines whether the pin acts as an input (BIDIROE = 0) or an output (BIDIROE = 1). If SPC0 = 1 and master mode is selected, this pin is not used by the SPI and reverts to being a general-purpose port I/O pin. 15.2.4 SS — Slave Select When the SPI is enabled as a slave, this pin is the low-true slave select input. When the SPI is enabled as a master and mode fault enable is off (MODFEN = 0), this pin is not used by the SPI and reverts to being a general-purpose port I/O pin. When the SPI is enabled as a master and MODFEN = 1, the slave select output enable bit determines whether this pin acts as the mode fault input (SSOE = 0) or as the slave select output (SSOE = 1). 15.3 Register Definition The SPI has eight 8-bit registers to select SPI options, control baud rate, report SPI status, hold an SPI data match value, and for transmit/receive data. Refer to the direct-page register summary in the Memory chapter of this data sheet for the absolute address assignments for all SPI registers. This section refers to registers and control bits only by their names, and a Freescale-provided equate or header file is used to translate these names into the appropriate absolute addresses. 15.3.1 SPI Control Register 1 (SPIxC1) This read/write register includes the SPI enable control, interrupt enables, and configuration options. 7 6 5 4 3 2 1 0 R SPIE W Reset 0 0 0 0 0 1 0 0 SPE SPTIE MSTR CPOL CPHA SSOE LSBFE Figure 15-5. SPI Control Register 1 (SPIxC1) MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 249 Serial Peripheral Interface (S08SPI16V1) Table 15-1. SPIxC1 Field Descriptions Field 7 SPIE Description SPI Interrupt Enable (for SPRF and MODF) — This is the interrupt enable for SPI receive buffer full (SPRF) and mode fault (MODF) events. 0 Interrupts from SPRF and MODF inhibited (use polling) 1 When SPRF or MODF is 1, request a hardware interrupt SPI System Enable — This bit enables the SPI system and dedicates the SPI port pins to SPI system functions. If SPE is cleared, SPI is disabled and forced into idle state, and all status bits in the SPIxS register are reset. 0 SPI system inactive 1 SPI system enabled SPI Transmit Interrupt Enable — This is the interrupt enable bit for SPI transmit buffer empty (SPTEF). 0 Interrupts from SPTEF inhibited (use polling) 1 When SPTEF is 1, hardware interrupt requested Master/Slave Mode Select — This bit selects master or slave mode operation. 0 SPI module configured as a slave SPI device 1 SPI module configured as a master SPI device Clock Polarity — This bit selects an inverted or non-inverted SPI clock. To transmit data between SPI modules, the SPI modules must have identical CPOL values. This bit effectively places an inverter in series with the clock signal from a master SPI or to a slave SPI device. Refer to Section 15.4.5, “SPI Clock Formats” for more details. 0 Active-high SPI clock (idles low) 1 Active-low SPI clock (idles high) Clock Phase — This bit selects one of two clock formats for different kinds of synchronous serial peripheral devices. Refer to Section 15.4.5, “SPI Clock Formats” for more details. 0 First edge on SPSCK occurs at the middle of the first cycle of a data transfer 1 First edge on SPSCK occurs at the start of the first cycle of a data transfer Slave Select Output Enable — This bit is used in combination with the mode fault enable (MODFEN) bit in SPIxC2 and the master/slave (MSTR) control bit to determine the function of the SS pin as shown in Table 15-2. LSB First (Shifter Direction) — This bit does not affect the position of the MSB and LSB in the data register. Reads and writes of the data register always have the MSB in bit 7 (or bit 15 in 16-bit mode). 0 SPI serial data transfers start with most significant bit 1 SPI serial data transfers start with least significant bit 6 SPE 5 SPTIE 4 MSTR 3 CPOL 2 CPHA 1 SSOE 0 LSBFE Table 15-2. SS Pin Function MODFEN 0 0 1 1 SSOE 0 1 0 1 Master Mode General-purpose I/O (not SPI) General-purpose I/O (not SPI) SS input for mode fault Automatic SS output Slave Mode Slave select input Slave select input Slave select input Slave select input 15.3.2 SPI Control Register 2 (SPIxC2) This read/write register is used to control optional features of the SPI system. Bits 6 and 5 are not implemented and always read 0. MC9S08JM60 Series Data Sheet, Rev. 3 250 Freescale Semiconductor Serial Peripheral Interface (S08SPI16V1) 7 6 5 4 3 2 1 0 R SPMIE W Reset 0 0 SPIMODE 0 MODFEN 0 0 BIDIROE 0 0 SPISWAI 0 0 SPC0 0 = Unimplemented or Reserved Figure 15-6. SPI Control Register 2 (SPIxC2) Table 15-3. SPIxC2 Register Field Descriptions Field 7 SPMIE Description SPI Match Interrupt Enable — This is the interrupt enable for the SPI receive data buffer hardware match (SPMF) function. 0 Interrupts from SPMF inhibited (use polling). 1 When SPMF = 1, requests a hardware interrupt. SPI 8- or 16-bit Mode — This bit allows the user to select either an 8-bit or 16-bit SPI data transmission length. In master mode, a change of this bit will abort a transmission in progress, force the SPI system into idle state, and reset all status bits in the SPIxS register. Refer to section Section 15.4.4, “Data Transmission Length,” for details. 0 8-bit SPI shift register, match register, and buffers. 1 16-bit SPI shift register, match register, and buffers. Master Mode-Fault Function Enable — When the SPI is configured for slave mode, this bit has no meaning or effect. (The SS pin is the slave select input.) In master mode, this bit determines how the SS pin is used (refer to Table 15-2 for details) 0 Mode fault function disabled, master SS pin reverts to general-purpose I/O not controlled by SPI 1 Mode fault function enabled, master SS pin acts as the mode fault input or the slave select output Bidirectional Mode Output Enable — When bidirectional mode is enabled by SPI pin control 0 (SPC0) = 1, BIDIROE determines whether the SPI data output driver is enabled to the single bidirectional SPI I/O pin. Depending on whether the SPI is configured as a master or a slave, it uses either the MOSI (MOMI) or MISO (SISO) pin, respectively, as the single SPI data I/O pin. When SPC0 = 0, BIDIROE has no meaning or effect. 0 Output driver disabled so SPI data I/O pin acts as an input 1 SPI I/O pin enabled as an output SPI Stop in Wait Mode — This bit is used for power conservation while in wait. 0 SPI clocks continue to operate in wait mode 1 SPI clocks stop when the MCU enters wait mode SPI Pin Control 0 — This bit enables bidirectional pin configurations as shown in Table 15-4. 0 SPI uses separate pins for data input and data output. 1 SPI configured for single-wire bidirectional operation. 6 SPIMODE 4 MODFEN 3 BIDIROE 1 SPISWAI 0 SPC0 MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 251 Serial Peripheral Interface (S08SPI16V1) Table 15-4. Bidirectional Pin Configurations Pin Mode SPC0 BIDIROE MISO MOSI Master Mode of Operation Normal Bidirectional 0 1 X 0 1 Slave Mode of Operation Normal Bidirectional 0 1 X 0 1 Slave Out Slave In Slave I/O Slave In MOSI not used by SPI Master In MISO not used by SPI Master Out Master In Master I/O 15.3.3 SPI Baud Rate Register (SPIxBR) This register is used to set the prescaler and bit rate divisor for an SPI master. This register may be read or written at any time. 7 6 5 4 3 2 1 0 R W Reset 0 SPPR2 0 0 SPPR1 0 SPPR0 0 0 SPR2 0 0 SPR1 0 SPR0 0 = Unimplemented or Reserved Figure 15-7. SPI Baud Rate Register (SPIxBR) Table 15-5. SPIxBR Register Field Descriptions Field 6:4 SPPR[2:0] Description SPI Baud Rate Prescale Divisor — This 3-bit field selects one of eight divisors for the SPI baud rate prescaler as shown in Table 15-6. The input to this prescaler is the bus rate clock (BUSCLK). The output of this prescaler drives the input of the SPI baud rate divider (see Figure 15-15). See Section 15.4.6, “SPI Baud Rate Generation,” for details. SPI Baud Rate Divisor — This 3-bit field selects one of eight divisors for the SPI baud rate divider as shown in Table 15-7. The input to this divider comes from the SPI baud rate prescaler (see Figure 15-15). See Section 15.4.6, “SPI Baud Rate Generation,” for details. 2:0 SPR[2:0] MC9S08JM60 Series Data Sheet, Rev. 3 252 Freescale Semiconductor Serial Peripheral Interface (S08SPI16V1) Table 15-6. SPI Baud Rate Prescaler Divisor SPPR2:SPPR1:SPPR0 0:0:0 0:0:1 0:1:0 0:1:1 1:0:0 1:0:1 1:1:0 1:1:1 Prescaler Divisor 1 2 3 4 5 6 7 8 Table 15-7. SPI Baud Rate Divisor SPR2:SPR1:SPR0 0:0:0 0:0:1 0:1:0 0:1:1 1:0:0 1:0:1 1:1:0 1:1:1 Rate Divisor 2 4 8 16 32 64 128 256 15.3.4 SPI Status Register (SPIxS) This register has four read-only status bits. Bits 3 through 0 are not implemented and always read 0. Writes have no meaning or effect. 7 6 5 4 3 2 1 0 R W Reset SPRF SPMF SPTEF MODF 0 0 0 0 0 0 1 0 0 0 0 0 = Unimplemented or Reserved Figure 15-8. SPI Status Register (SPIxS) MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 253 Serial Peripheral Interface (S08SPI16V1) Table 15-8. SPIxS Register Field Descriptions Field 7 SPRF Description SPI Read Buffer Full Flag — SPRF is set at the completion of an SPI transfer to indicate that received data may be read from the SPI data register (SPIxDH:SPIxDL). SPRF is cleared by reading SPRF while it is set, then reading the SPI data register. 0 No data available in the receive data buffer. 1 Data available in the receive data buffer. SPI Match Flag — SPMF is set after SPRF = 1 when the value in the receive data buffer matches the value in SPIMH:SPIML. To clear the flag, read SPMF when it is set, then write a 1 to it. 0 Value in the receive data buffer does not match the value in SPIxMH:SPIxML registers. 1 Value in the receive data buffer matches the value in SPIxMH:SPIxML registers. SPI Transmit Buffer Empty Flag — This bit is set when the transmit data buffer is empty. It is cleared by reading SPIxS with SPTEF set, followed by writing a data value to the transmit buffer at SPIxDH:SPIxDL. SPIxS must be read with SPTEF = 1 before writing data to SPIxDH:SPIxDL or the SPIxDH:SPIxDL write will be ignored. SPTEF is automatically set when all data from the transmit buffer transfers into the transmit shift register. For an idle SPI, data written to SPIxDH:SPIxDL is transferred to the shifter almost immediately so SPTEF is set within two bus cycles allowing a second data to be queued into the transmit buffer. After completion of the transfer of the data in the shift register, the queued data from the transmit buffer will automatically move to the shifter and SPTEF will be set to indicate there is room for new data in the transmit buffer. If no new data is waiting in the transmit buffer, SPTEF simply remains set and no data moves from the buffer to the shifter. 0 SPI transmit buffer not empty 1 SPI transmit buffer empty Master Mode Fault Flag — MODF is set if the SPI is configured as a master and the slave select input goes low, indicating some other SPI device is also configured as a master. The SS pin acts as a mode fault error input only when MSTR = 1, MODFEN = 1, and SSOE = 0; otherwise, MODF will never be set. MODF is cleared by reading MODF while it is 1, then writing to SPI control register 1 (SPIxC1). 0 No mode fault error 1 Mode fault error detected 6 SPMF 5 SPTEF 4 MODF 15.3.5 SPI Data Registers (SPIxDH:SPIxDL) 7 6 5 4 3 2 1 0 R Bit 15 W Reset 0 0 0 0 0 0 0 0 14 13 12 11 10 9 Bit 8 Figure 15-9. SPI Data Register High (SPIxDH) 7 6 5 4 3 2 1 0 R Bit 7 W Reset 0 0 0 0 0 0 0 0 6 5 4 3 2 1 Bit 0 Figure 15-10. SPI Data Register Low (SPIxDL) The SPI data registers (SPIxDH:SPIxDL) are both the input and output register for SPI data. A write to these registers writes to the transmit data buffer, allowing data to be queued and transmitted. MC9S08JM60 Series Data Sheet, Rev. 3 254 Freescale Semiconductor Serial Peripheral Interface (S08SPI16V1) When the SPI is configured as a master, data queued in the transmit data buffer is transmitted immediately after the previous transmission has completed. The SPI transmit buffer empty flag (SPTEF) in the SPIxS register indicates when the transmit data buffer is ready to accept new data. SPIxS must be read when SPTEF is set before writing to the SPI data registers, or the write will be ignored. Data may be read from SPIxDH:SPIxDL any time after SPRF is set and before another transfer is finished. Failure to read the data out of the receive data buffer before a new transfer ends causes a receive overrun condition and the data from the new transfer is lost. In 8-bit mode, only SPIxDL is available. Reads of SPIxDH will return all 0s. Writes to SPIxDH will be ignored. In 16-bit mode, reading either byte (SPIxDH or SPIxDL) latches the contents of both bytes into a buffer where they remain latched until the other byte is read. Writing to either byte (SPIxDH or SPIxDL) latches the value into a buffer. When both bytes have been written, they are transferred as a coherent 16-bit value into the transmit data buffer. 15.3.6 SPI Match Registers (SPIxMH:SPIxML) These read/write registers contain the hardware compare value, which sets the SPI match flag (SPMF) when the value received in the SPI receive data buffer equals the value in the SPIxMH:SPIxML registers. In 8-bit mode, only SPIxML is available. Reads of SPIxMH will return all 0s. Writes to SPIxMH will be ignored. In 16-bit mode, reading either byte (SPIxMH or SPIxML) latches the contents of both bytes into a buffer where they remain latched until the other byte is read. Writing to either byte (SPIxMH or SPIxML) latches the value into a buffer. When both bytes have been written, they are transferred as a coherent value into the SPI match registers. 7 6 5 4 3 2 1 0 R Bit 15 W Reset 0 0 0 0 0 0 0 0 14 13 12 11 10 9 Bit 8 Figure 15-11. SPI Match Register High (SPIxMH) 7 6 5 4 3 2 1 0 R Bit 7 W Reset 0 0 0 0 0 0 0 0 6 5 4 3 2 1 Bit 0 Figure 15-12. SPI Match Register Low (SPIxML) MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 255 Serial Peripheral Interface (S08SPI16V1) 15.4 15.4.1 Functional Description General The SPI system is enabled by setting the SPI enable (SPE) bit in SPI Control Register 1. While the SPE bit is set, the four associated SPI port pins are dedicated to the SPI function as: • Slave select (SS) • Serial clock (SPSCK) • Master out/slave in (MOSI) • Master in/slave out (MISO) An SPI transfer is initiated in the master SPI device by reading the SPI status register (SPIxS) when SPTEF = 1 and then writing data to the transmit data buffer (write to SPIxDH:SPIxDL). When a transfer is complete, received data is moved into the receive data buffer. The SPIxDH:SPIxDL registers act as the SPI receive data buffer for reads and as the SPI transmit data buffer for writes. The clock phase control bit (CPHA) and a clock polarity control bit (CPOL) in the SPI Control Register 1 (SPIxC1) select one of four possible clock formats to be used by the SPI system. The CPOL bit simply selects a non-inverted or inverted clock. The CPHA bit is used to accommodate two fundamentally different protocols by sampling data on odd numbered SPSCK edges or on even numbered SPSCK edges. The SPI can be configured to operate as a master or as a slave. When the MSTR bit in SPI control register 1 is set, master mode is selected, when the MSTR bit is clear, slave mode is selected. 15.4.2 Master Mode The SPI operates in master mode when the MSTR bit is set. Only a master SPI module can initiate transmissions. A transmission begins by reading the SPIxS register while SPTEF = 1 and writing to the master SPI data registers. If the shift register is empty, the byte immediately transfers to the shift register. The data begins shifting out on the MOSI pin under the control of the serial clock. • SPSCK The SPR2, SPR1, and SPR0 baud rate selection bits in conjunction with the SPPR2, SPPR1, and SPPR0 baud rate preselection bits in the SPI Baud Rate register control the baud rate generator and determine the speed of the transmission. The SPSCK pin is the SPI clock output. Through the SPSCK pin, the baud rate generator of the master controls the shift register of the slave peripheral. • MOSI, MISO pin In master mode, the function of the serial data output pin (MOSI) and the serial data input pin (MISO) is determined by the SPC0 and BIDIROE control bits. • SS pin If MODFEN and SSOE bit are set, the SS pin is configured as slave select output. The SS output becomes low during each transmission and is high when the SPI is in idle state. If MODFEN is set and SSOE is cleared, the SS pin is configured as input for detecting mode fault error. If the SS input becomes low this indicates a mode fault error where another master tries to drive the MOSI MC9S08JM60 Series Data Sheet, Rev. 3 256 Freescale Semiconductor Serial Peripheral Interface (S08SPI16V1) and SPSCK lines. In this case, the SPI immediately switches to slave mode, by clearing the MSTR bit and also disables the slave output buffer MISO (or SISO in bidirectional mode). So the result is that all outputs are disabled and SPSCK, MOSI and MISO are inputs. If a transmission is in progress when the mode fault occurs, the transmission is aborted and the SPI is forced into idle state. This mode fault error also sets the mode fault (MODF) flag in the SPI Status Register (SPIxS). If the SPI interrupt enable bit (SPIE) is set when the MODF flag gets set, then an SPI interrupt sequence is also requested. When a write to the SPI Data Register in the master occurs, there is a half SPSCK-cycle delay. After the delay, SPSCK is started within the master. The rest of the transfer operation differs slightly, depending on the clock format specified by the SPI clock phase bit, CPHA, in SPI Control Register 1 (see Section 15.4.5, “SPI Clock Formats.”) NOTE A change of the bits CPOL, CPHA, SSOE, LSBFE, MODFEN, SPC0, BIDIROE with SPC0 set, SPIMODE, SPPR2-SPPR0 and SPR2-SPR0 in master mode will abort a transmission in progress and force the SPI into idle state. The remote slave cannot detect this, therefore the master has to ensure that the remote slave is set back to idle state. 15.4.3 Slave Mode The SPI operates in slave mode when the MSTR bit in SPI Control Register1 is clear. • SPSCK In slave mode, SPSCK is the SPI clock input from the master. • MISO, MOSI pin In slave mode, the function of the serial data output pin (MISO) and serial data input pin (MOSI) is determined by the SPC0 bit and BIDIROE bit in SPI Control Register 2. • SS pin The SS pin is the slave select input. Before a data transmission occurs, the SS pin of the slave SPI must be low. SS must remain low until the transmission is complete. If SS goes high, the SPI is forced into idle state. The SS input also controls the serial data output pin, if SS is high (not selected), the serial data output pin is high impedance, and, if SS is low the first bit in the SPI Data Register is driven out of the serial data output pin. Also, if the slave is not selected (SS is high), then the SPSCK input is ignored and no internal shifting of the SPI shift register takes place. Although the SPI is capable of duplex operation, some SPI peripherals are capable of only receiving SPI data in a slave mode. For these simpler devices, there is no serial data out pin. MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 257 Serial Peripheral Interface (S08SPI16V1) NOTE When peripherals with duplex capability are used, take care not to simultaneously enable two receivers whose serial outputs drive the same system slave’s serial data output line. As long as no more than one slave device drives the system slave’s serial data output line, it is possible for several slaves to receive the same transmission from a master, although the master would not receive return information from all of the receiving slaves. If the CPHA bit in SPI Control Register 1 is clear, odd numbered edges on the SPSCK input cause the data at the serial data input pin to be latched. Even numbered edges cause the value previously latched from the serial data input pin to shift into the LSB or MSB of the SPI shift register, depending on the LSBFE bit. If the CPHA bit is set, even numbered edges on the SPSCK input cause the data at the serial data input pin to be latched. Odd numbered edges cause the value previously latched from the serial data input pin to shift into the LSB or MSB of the SPI shift register, depending on the LSBFE bit. When CPHA is set, the first edge is used to get the first data bit onto the serial data output pin. When CPHA is clear and the SS input is low (slave selected), the first bit of the SPI data is driven out of the serial data output pin. After the eighth (SPIMODE = 0) or sixteenth (SPIMODE = 1) shift, the transfer is considered complete and the received data is transferred into the SPI data registers. To indicate transfer is complete, the SPRF flag in the SPI Status Register is set. NOTE A change of the bits CPOL, CPHA, SSOE, LSBFE, MODFEN, SPC0 and BIDIROE with SPC0 set and SPIMODE in slave mode will corrupt a transmission in progress and has to be avoided. 15.4.4 Data Transmission Length The SPI can support data lengths of 8 or 16 bits. The length can be configured with the SPIMODE bit in the SPIxC2 register. In 8-bit mode (SPIMODE = 0), the SPI Data Register is comprised of one byte: SPIxDL. The SPI Match Register is also comprised of only one byte: SPIxML. Reads of SPIxDH and SPIxMH will return zero. Writes to SPIxDH and SPIxMH will be ignored. In 16-bit mode (SPIMODE = 1), the SPI Data Register is comprised of two bytes: SPIxDH and SPIxDL. Reading either byte (SPIxDH or SPIxDL) latches the contents of both bytes into a buffer where they remain latched until the other byte is read. Writing to either byte (SPIxDH or SPIxDL) latches the value into a buffer. When both bytes have been written, they are transferred as a coherent 16-bit value into the transmit data buffer. In 16-bit mode, the SPI Match Register is also comprised of two bytes: SPIxMH and SPIxML. Reading either byte (SPIxMH or SPIxML) latches the contents of both bytes into a buffer where they remain latched until the other byte is read. Writing to either byte (SPIxMH or SPIxML) latches the value into a buffer. When both bytes have been written, they are transferred as a coherent 16-bit value into the transmit data buffer. MC9S08JM60 Series Data Sheet, Rev. 3 258 Freescale Semiconductor Serial Peripheral Interface (S08SPI16V1) Any switching between 8- and 16-bit data transmission length (controlled by SPIMODE bit) in master mode will abort a transmission in progress, force the SPI system into idle state, and reset all status bits in the SPIxS register. To initiate a transfer after writing to SPIMODE, the SPIxS register must be read with SPTEF = 1, and data must be written to SPIxDH:SPIxDL in 16-bit mode (SPIMODE = 1) or SPIxDL in 8-bit mode (SPIMODE = 0). In slave mode, user software should write to SPIMODE only once to prevent corrupting a transmission in progress. NOTE Data can be lost if the data length is not the same for both master and slave devices. 15.4.5 SPI Clock Formats To accommodate a wide variety of synchronous serial peripherals from different manufacturers, the SPI system has a clock polarity (CPOL) bit and a clock phase (CPHA) control bit to select one of four clock formats for data transfers. CPOL selectively inserts an inverter in series with the clock. CPHA chooses between two different clock phase relationships between the clock and data. Figure 15-13 shows the clock formats when SPIMODE = 0 (8-bit mode) and CPHA = 1. At the top of the figure, the eight bit times are shown for reference with bit 1 starting at the first SPSCK edge and bit 8 ending one-half SPSCK cycle after the sixteenth SPSCK edge. The MSB first and LSB first lines show the order of SPI data bits depending on the setting in LSBFE. Both variations of SPSCK polarity are shown, but only one of these waveforms applies for a specific transfer, depending on the value in CPOL. The SAMPLE IN waveform applies to the MOSI input of a slave or the MISO input of a master. The MOSI waveform applies to the MOSI output pin from a master and the MISO waveform applies to the MISO output from a slave. The SS OUT waveform applies to the slave select output from a master (provided MODFEN and SSOE = 1). The master SS output goes to active low one-half SPSCK cycle before the start of the transfer and goes back high at the end of the eighth bit time of the transfer. The SS IN waveform applies to the slave select input of a slave. MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 259 Serial Peripheral Interface (S08SPI16V1) BIT TIME # (REFERENCE) 1 2 ... 6 7 8 SPSCK (CPOL = 0) SPSCK (CPOL = 1) SAMPLE IN (MISO OR MOSI) MOSI (MASTER OUT) MSB FIRST LSB FIRST MISO (SLAVE OUT) BIT 7 BIT 0 BIT 6 BIT 1 ... ... BIT 2 BIT 5 BIT 1 BIT 6 BIT 0 BIT 7 SS OUT (MASTER) SS IN (SLAVE) Figure 15-13. SPI Clock Formats (CPHA = 1) When CPHA = 1, the slave begins to drive its MISO output when SS goes to active low, but the data is not defined until the first SPSCK edge. The first SPSCK edge shifts the first bit of data from the shifter onto the MOSI output of the master and the MISO output of the slave. The next SPSCK edge causes both the master and the slave to sample the data bit values on their MISO and MOSI inputs, respectively. At the third SPSCK edge, the SPI shifter shifts one bit position which shifts in the bit value that was just sampled, and shifts the second data bit value out the other end of the shifter to the MOSI and MISO outputs of the master and slave, respectively. When CPHA = 1, the slave’s SS input is not required to go to its inactive high level between transfers. Figure 15-14 shows the clock formats when SPIMODE = 0 and CPHA = 0. At the top of the figure, the eight bit times are shown for reference with bit 1 starting as the slave is selected (SS IN goes low), and bit 8 ends at the last SPSCK edge. The MSB first and LSB first lines show the order of SPI data bits depending on the setting in LSBFE. Both variations of SPSCK polarity are shown, but only one of these waveforms applies for a specific transfer, depending on the value in CPOL. The SAMPLE IN waveform applies to the MOSI input of a slave or the MISO input of a master. The MOSI waveform applies to the MOSI output pin from a master and the MISO waveform applies to the MISO output from a slave. The SS OUT waveform applies to the slave select output from a master (provided MODFEN and SSOE = 1). The master SS output goes to active low at the start of the first bit time of the transfer and goes back high one-half MC9S08JM60 Series Data Sheet, Rev. 3 260 Freescale Semiconductor Serial Peripheral Interface (S08SPI16V1) SPSCK cycle after the end of the eighth bit time of the transfer. The SS IN waveform applies to the slave select input of a slave. BIT TIME # (REFERENCE) SPSCK (CPOL = 0) 1 2 ... 6 7 8 SPSCK (CPOL = 1) SAMPLE IN (MISO OR MOSI) MOSI (MASTER OUT) MSB FIRST LSB FIRST MISO (SLAVE OUT) BIT 7 BIT 0 BIT 6 BIT 1 ... ... BIT 2 BIT 5 BIT 1 BIT 6 BIT 0 BIT 7 SS OUT (MASTER) SS IN (SLAVE) Figure 15-14. SPI Clock Formats (CPHA = 0) When CPHA = 0, the slave begins to drive its MISO output with the first data bit value (MSB or LSB depending on LSBFE) when SS goes to active low. The first SPSCK edge causes both the master and the slave to sample the data bit values on their MISO and MOSI inputs, respectively. At the second SPSCK edge, the SPI shifter shifts one bit position which shifts in the bit value that was just sampled and shifts the second data bit value out the other end of the shifter to the MOSI and MISO outputs of the master and slave, respectively. When CPHA = 0, the slave’s SS input must go to its inactive high level between transfers. 15.4.6 SPI Baud Rate Generation As shown in Figure 15-15, the clock source for the SPI baud rate generator is the bus clock. The three prescale bits (SPPR2:SPPR1:SPPR0) choose a prescale divisor of 1, 2, 3, 4, 5, 6, 7, or 8. The three rate select bits (SPR2:SPR1:SPR0) divide the output of the prescaler stage by 2, 4, 8, 16, 32, 64, 128, or 256 to get the internal SPI master mode bit-rate clock. The baud rate generator is activated only when the SPI is in the master mode and a serial transfer is taking place. In the other cases, the divider is disabled to decrease IDD current. MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 261 Serial Peripheral Interface (S08SPI16V1) The baud rate divisor equation is as follows: BaudRateDivisor = ( SPPR + 1 ) • 2 ( SPR + 1 ) The baud rate can be calculated with the following equation: Baud Rate = BusClock ⁄ BaudRateDivisor PRESCALER BUS CLOCK DIVIDE BY 1, 2, 3, 4, 5, 6, 7, or 8 BAUD RATE DIVIDER DIVIDE BY 2, 4, 8, 16, 32, 64, 128, or 256 MASTER SPI BIT RATE SPPR2:SPPR1:SPPR0 SPR2:SPR1:SPR0 Figure 15-15. SPI Baud Rate Generation 15.4.7 15.4.7.1 Special Features SS Output The SS output feature automatically drives the SS pin low during transmission to select external devices and drives it high during idle to deselect external devices. When SS output is selected, the SS output pin is connected to the SS input pin of the external device. The SS output is available only in master mode during normal SPI operation by asserting the SSOE and MODFEN bits as shown in Table 15-2. The mode fault feature is disabled while SS output is enabled. NOTE Care must be taken when using the SS output feature in a multi-master system since the mode fault feature is not available for detecting system errors between masters. 15.4.7.2 Bidirectional Mode (MOMI or SISO) The bidirectional mode is selected when the SPC0 bit is set in SPI Control Register 2 (see Table 15-9.) In this mode, the SPI uses only one serial data pin for the interface with external device(s). The MSTR bit decides which pin to use. The MOSI pin becomes the serial data I/O (MOMI) pin for the master mode, and the MISO pin becomes serial data I/O (SISO) pin for the slave mode. The MISO pin in master mode and MOSI pin in slave mode are not used by the SPI. MC9S08JM60 Series Data Sheet, Rev. 3 262 Freescale Semiconductor Serial Peripheral Interface (S08SPI16V1) Table 15-9. Normal Mode and Bidirectional Mode When SPE = 1 Master Mode MSTR = 1 Slave Mode MSTR = 0 Serial Out MOSI Serial In SPI MOSI Normal Mode SPC0 = 0 SPI Serial In MISO Serial Out MISO Serial Out MOMI BIDIROE Serial In BIDIROE SPI Serial Out SISO Bidirectional Mode SPC0 = 1 SPI Serial In . The direction of each serial I/O pin depends on the BIDIROE bit. If the pin is configured as an output, serial data from the shift register is driven out on the pin. The same pin is also the serial input to the shift register. The SPSCK is output for the master mode and input for the slave mode. The SS is the input or output for the master mode, and it is always the input for the slave mode. The bidirectional mode does not affect SPSCK and SS functions. NOTE In bidirectional master mode, with mode fault enabled, both data pins MISO and MOSI can be occupied by the SPI, though MOSI is normally used for transmissions in bidirectional mode and MISO is not used by the SPI. If a mode fault occurs, the SPI is automatically switched to slave mode, in this case MISO becomes occupied by the SPI and MOSI is not used. This has to be considered, if the MISO pin is used for another purpose. 15.4.8 Error Conditions The SPI has one error condition: • Mode fault error 15.4.8.1 Mode Fault Error If the SS input becomes low while the SPI is configured as a master, it indicates a system error where more than one master may be trying to drive the MOSI and SPSCK lines simultaneously. This condition is not permitted in normal operation, and the MODF bit in the SPI status register is set automatically provided the MODFEN bit is set. MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 263 Serial Peripheral Interface (S08SPI16V1) In the special case where the SPI is in master mode and MODFEN bit is cleared, the SS pin is not used by the SPI. In this special case, the mode fault error function is inhibited and MODF remains cleared. In case the SPI system is configured as a slave, the SS pin is a dedicated input pin. Mode fault error doesn’t occur in slave mode. If a mode fault error occurs the SPI is switched to slave mode, with the exception that the slave output buffer is disabled. So SPSCK, MISO and MOSI pins are forced to be high impedance inputs to avoid any possibility of conflict with another output driver. A transmission in progress is aborted and the SPI is forced into idle state. If the mode fault error occurs in the bidirectional mode for a SPI system configured in master mode, output enable of the MOMI (MOSI in bidirectional mode) is cleared if it was set. No mode fault error occurs in the bidirectional mode for the SPI system configured in slave mode. The mode fault flag is cleared automatically by a read of the SPI Status Register (with MODF set) followed by a write to SPI Control Register 1. If the mode fault flag is cleared, the SPI becomes a normal master or slave again. 15.4.9 15.4.9.1 Low Power Mode Options SPI in Run Mode In run mode with the SPI system enable (SPE) bit in the SPI control register clear, the SPI system is in a low-power, disabled state. SPI registers can still be accessed, but clocks to the core of this module are disabled. 15.4.9.2 SPI in Wait Mode SPI operation in wait mode depends upon the state of the SPISWAI bit in SPI Control Register 2. • If SPISWAI is clear, the SPI operates normally when the CPU is in wait mode • If SPISWAI is set, SPI clock generation ceases and the SPI module enters a power conservation state when the CPU is in wait mode. — If SPISWAI is set and the SPI is configured for master, any transmission and reception in progress stops at wait mode entry. The transmission and reception resumes when the SPI exits wait mode. – If SPISWAI is set and the SPI is configured as a slave, any transmission and reception in progress continues if the SPSCK continues to be driven from the master. This keeps the slave synchronized to the master and the SPSCK. If the master transmits data while the slave is in wait mode, the slave will continue to send out data consistent with the operation mode at the start of wait mode (i.e., if the slave is currently sending its SPIxDH:SPIxDL to the master, it will continue to send the same byte. Otherwise, if the slave is currently sending the last data received byte from the master, it will continue to send each previously receive data from the master byte). MC9S08JM60 Series Data Sheet, Rev. 3 264 Freescale Semiconductor Serial Peripheral Interface (S08SPI16V1) NOTE Care must be taken when expecting data from a master while the slave is in wait or stop3 mode. Even though the shift register will continue to operate, the rest of the SPI is shut down (i.e. a SPRF interrupt will not be generated until exiting stop or wait mode). Also, the data from the shift register will not be copied into the SPIxDH:SPIxDL registers until after the slave SPI has exited wait or stop mode. A SPRF flag and SPIxDH:SPIxDL copy is only generated if wait mode is entered or exited during a tranmission. If the slave enters wait mode in idle mode and exits wait mode in idle mode, neither a SPRF nor a SPIxDH:SPIxDL copy will occur. 15.4.9.3 SPI in Stop Mode Stop3 mode is dependent on the SPI system. Upon entry to stop3 mode, the SPI module clock is disabled (held high or low). If the SPI is in master mode and exchanging data when the CPU enters stop mode, the transmission is frozen until the CPU exits stop mode. After stop, data to and from the external SPI is exchanged correctly. In slave mode, the SPI will stay synchronized with the master. The stop mode is not dependent on the SPISWAI bit. In all other stop modes, the SPI module is completely disabled. After stop, all registers are reset to their default values, and the SPI module must be re-initialized. 15.4.9.4 Reset The reset values of registers and signals are described in Section 15.3, “Register Definition.” which details the registers and their bit-fields. • If a data transmission occurs in slave mode after reset without a write to SPIxDH:SPIxDL, it will transmit garbage, or the data last received from the master before the reset. • Reading from the SPIxDH:SPIxDL after reset will always read zeros. 15.4.9.5 Interrupts The SPI only originates interrupt requests when the SPI is enabled (SPE bit in SPIxC1 set). The following is a description of how the SPI makes a request and how the MCU should acknowledge that request. The interrupt vector offset and interrupt priority are chip dependent. 15.4.10 SPI Interrupts There are four flag bits, three interrupt mask bits, and one interrupt vector associated with the SPI system. The SPI interrupt enable mask (SPIE) enables interrupts from the SPI receiver full flag (SPRF) and mode fault flag (MODF). The SPI transmit interrupt enable mask (SPTIE) enables interrupts from the SPI transmit buffer empty flag (SPTEF). The SPI match interrupt enable mask bit (SPIMIE) enables interrupts from the SPI match flag (SPMF). When one of the flag bits is set, and the associated interrupt mask bit is set, a hardware interrupt request is sent to the CPU. If the interrupt mask bits are cleared, software can poll the associated flag bits instead of using interrupts. The SPI interrupt service routine (ISR) should check MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 265 Serial Peripheral Interface (S08SPI16V1) the flag bits to determine what event caused the interrupt. The service routine should also clear the flag bit(s) before returning from the ISR (usually near the beginning of the ISR). 15.4.10.1 MODF MODF occurs when the master detects an error on the SS pin. The master SPI must be configured for the MODF feature (see Table 15-2). Once MODF is set, the current transfer is aborted and the following bit is changed: • MSTR=0, The master bit in SPIxC1 resets. The MODF interrupt is reflected in the status register MODF flag. Clearing the flag will also clear the interrupt. This interrupt will stay active while the MODF flag is set. MODF has an automatic clearing process which is described in Section 15.3.4, “SPI Status Register (SPIxS).” 15.4.10.2 SPRF SPRF occurs when new data has been received and copied to the SPI receive data buffer. In 8-bit mode, SPRF is set only after all 8 bits have been shifted out of the shift register and into SPIxDL. In 16-bit mode, SPRF is set only after all 16 bits have been shifted out of the shift register and into SPIxDH:SPIxDL. Once SPRF is set, it does not clear until it is serviced. SPRF has an automatic clearing process which is described in Section 15.3.4, “SPI Status Register (SPIxS).” In the event that the SPRF is not serviced before the end of the next transfer (i.e. SPRF remains active throughout another transfer), the latter transfers will be ignored and no new data will be copied into the SPIxDH:SPIxDL. 15.4.10.3 SPTEF SPTEF occurs when the SPI transmit buffer is ready to accept new data. In 8-bit mode, SPTEF is set only after all 8 bits have been moved from SPIxDL into the shifter. In 16-bit mode, SPTEF is set only after all 16 bits have been moved from SPIxDH:SPIxDL into the shifter. Once SPTEF is set, it does not clear until it is serviced. SPTEF has an automatic clearing process which is described in Section 15.3.4, “SPI Status Register (SPIxS). 15.4.10.4 SPMF SPMF occurs when the data in the receive data buffer is equal to the data in the SPI match register. In 8-bit mode, SPMF is set only after bits 8–0 in the receive data buffer are determined to be equivalent to the value in SPIxML. In 16-bit mode, SPMF is set after bits 15–0 in the receive data buffer are determined to be equivalent to the value in SPIxMH:SPIxML. MC9S08JM60 Series Data Sheet, Rev. 3 266 Freescale Semiconductor Serial Peripheral Interface (S08SPI16V1) 15.5 15.5.1 Initialization/Application Information SPI Module Initialization Example Initialization Sequence 15.5.1.1 Before the SPI module can be used for communication, an initialization procedure must be carried out, as follows: 1. Update control register 1 (SPIxC1) to enable the SPI and to control interrupt enables. This register also sets the SPI as master or slave, determines clock phase and polarity, and configures the main SPI options. 2. Update control register 2 (SPIxC2) to enable additional SPI functions such as the SPI match interrupt feature, the master mode-fault function, and bidirectional mode output. 8- or 16-bit mode select and other optional features are controlled here as well. 3. Update the baud rate register (SPIxBR) to set the prescaler and bit rate divisor for an SPI master. 4. Update the hardware match register (SPIxMH:SPIxML) with the value to be compared to the receive data register for triggering an interrupt if hardware match interrupts are enabled. 5. In the master, read SPIxS while SPTEF = 1, and then write to the transmit data register (SPIxDH:SPIxDL) to begin transfer. 15.5.1.2 Pseudo—Code Example In this example, the SPI module will be set up for master mode with only hardware match interrupts enabled. The SPI will run in 16-bit mode at a maximum baud rate of bus clock divided by 2. Clock phase and polarity will be set for an active-high SPI clock where the first edge on SPSCK occurs at the start of the first cycle of a data transfer. SPIxC1=0x54(%01010100) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 SPIE SPE SPTIE MSTR CPOL CPHA SSOE LSBFE =0 =1 =0 =1 =0 =1 =0 =0 Disables receive and mode fault interrupts Enables the SPI system Disables SPI transmit interrupts Sets the SPI module as a master SPI device Configures SPI clock as active-high First edge on SPSCK at start of first data transfer cycle Determines SS pin function when mode fault enabled SPI serial data transfers start with most significant bit MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 267 Serial Peripheral Interface (S08SPI16V1) SPIxC2 = 0xC0(%11000000) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 SPISWAI SPC0 MODFEN BIDIROE SPMIE SPIMODE =1 =1 =0 =0 =0 =0 =0 =0 SPI hardware match interrupt enabled Configures SPI for 16-bit mode Unimplemented Disables mode fault function SPI data I/O pin acts as input Unimplemented SPI clocks operate in wait mode uses separate pins for data input and output SPIxBR = 0x00(%00000000) Bit 7 Bit 6:4 Bit 3 Bit 2:0 =0 = 000 =0 = 000 Unimplemented Sets prescale divisor to 1 Unimplemented Sets baud rate divisor to 2 SPIxS = 0x00(%00000000) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3:0 SPRF SPMF SPTEF MODF =0 =0 =0 =0 =0 Flag is set when receive data buffer is full Flag is set when SPIMH/L = receive data buffer Flag is set when transmit data buffer is empty Mode fault flag for master mode Unimplemented SPIxMH = 0xXX In 16-bit mode, this register holds bits 8–15 of the hardware match buffer. In 8-bit mode, writes to this register will be ignored. SPIxML = 0xXX Holds bits 0–7 of the hardware match buffer. SPIxDH = 0xxx In 16-bit mode, this register holds bits 8–15 of the data to be transmitted by the transmit buffer and received by the receive buffer. SPIxDL = 0xxx Holds bits 0–7 of the data to be transmitted by the transmit buffer and received by the receive buffer. MC9S08JM60 Series Data Sheet, Rev. 3 268 Freescale Semiconductor Serial Peripheral Interface (S08SPI16V1) RESET INITIALIZE SPI SPIxC1 = 0x54 SPIxC2 = 0xC0 SPIxBR = 0x00 SPIxMH = 0xXX YES SPTEF = 1 ? YES WRITE TO SPIxDH:SPIxDL NO SPRF = 1 ? YES READ SPIxDH:SPIxDL NO SPMF = 1 ? YES READ SPMF WHILE SET TO CLEAR FLAG, THEN WRITE A 1 TO IT NO CONTINUE Figure 15-16. Initialization Flowchart Example for SPI Master Device in 16-bit Mode MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 269 Serial Peripheral Interface (S08SPI16V1) MC9S08JM60 Series Data Sheet, Rev. 3 270 Freescale Semiconductor Chapter 16 Timer/Pulse-Width Modulator (S08TPMV3) 16.1 Introduction The MC9S08JM60 series includes two independent timer/PWM (TPM) modules which support traditional input capture, output compare, or buffered edge-aligned pulse-width modulation (PWM) on each channel. A control bit in each TPM configures all channels in that timer to operate as center-aligned PWM functions. In each of these two TPMs, timing functions are based on a separate 16-bit counter with prescaler and modulo features to control frequency and range (period between overflows) of the time reference. MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 271 Chapter 16 Timer/Pulse-Width Modulator (S08TPMV3) USBDP USBDN PORT A 6 PTA5– PTA0 PTB7/ADP7 PTB6/ADP6 PTB5/KBIP5/ADP5 PTB4/KBIP4/ADP4 PTB3/SS2/ADP3 PTB2/SPSCK2/ADP2 PTB1/MOSI2/ADP1 PTB0/MISO2/ADP0 PTC6 PTC5/RxD2 PTC4 PTC3/TxD2 PTC2 PTC1/SDA PTC0/SCL HCS08 CORE ON-CHIP ICE AND DEBUG MODULE (DBG) FULL SPEED USB USB ENDPOINT TRANSCEIVER RAM 8-/16-BIT SERIAL PERIPHERAL INTERFACE MODULE (SPI2) SS2 SPSCK2 MOSI2 MISO2 RxD2 TxD2 SDA SCL USB SIE BKGD/MS BDC CPU RESET HCS08 SYSTEM CONTROL RESETS AND INTERRUPTS MODES OF OPERATION POWER MANAGEMENT IRQ/TPMCLK SERIAL COMMUNICATIONS INTERFACE MODULE (SCI2) COP IRQ LVD IIC MODULE (IIC) VDDAD VSSAD VREFL VREFH USER Flash (IN BYTES) MC9S08JM60 = 60,912 MC9S08JM32 = 32,768 12-CHANNEL, 12-BIT ANALOG-TO-DIGITAL CONVERTER (ADC) 8 4 PORT D PORT C PORT B ACMP– ANALOG COMPARATOR (ACMP) ACMP+ ACMPO SS1 SPSCK1 MOSI1 MISO1 6-CHANNEL TIMER/PWM MODULE (TPM1) SERIAL COMMUNICATIONS INTERFACE MODULE (SCI1) PORT E TPMCLK TPM1CH1 TPM1CH0 TPM1CHx 4 RxD1 TxD1 TPMCLK TPM2CH1 TPM2CH0 KBIPx 8-BIT KEYBOARD INTERRUPT MODULE (KBI) KBIPx EXTAL XTAL PTD7 PTD6 PTD5 PTD4/ADP11 PTD3/KBIP3/ADP10 PTD2/KBIP2/ACMPO PTD1/ADP9/ACMP– PTD0/ADP8/ACMP+ PTE7/SS1 PTE6/SPSCK1 PTE5/MOSI1 PTE4/MISO1 PTE3/TPM1CH1 PTE2/TPM1CH0 PTE1/RxD1 PTE0/TxD1 PTF7 PTF6 PTF5/TPM2CH1 PTF4/TPM2CH0 PTF3/TPM1CH5 PTF2/TPM1CH4 PTF1/TPM1CH3 PTF0/TPM1CH2 PTG5/EXTAL PTG4/XTAL PTG3/KBIP7 PTG2/KBIP6 PTG1/KBIP1 PTG0/KBIP0 USER RAM (IN BYTES) MC9S08JM60 = 4096 MC9S08JM32 = 2048 8-/16-BIT SERIAL PERIPHERAL INTERFACE MODULE (SPI1) MULTI-PURPOSE CLOCK GENERATOR (MCG) VSSOSC LOW-POWER OSCILLATOR SYSTEM VOLTAGE REGULATOR USB 3.3-V VOLTAGE REGULATOR REAL-TIME COUNTER (RTC) VDD VSS MODULE (TPM2) VUSB33 4 4 NOTES: 1. Port pins are software configurable with pullup device if input port. 2. Pin contains software configurable pullup/pull-down device if IRQ is enabled (IRQPE = 1). Pull-down is enabled if rising edge detect is selected (IRQEDG = 1) 3. IRQ does not have a clamp diode to VDD. IRQ must not be driven above VDD. 4. Pin contains integrated pullup device. 5. When pin functions as KBI (KBIPEn = 1) and associated pin is configured to enable the pullup device, KBEDGn can be used to reconfigure the pullup as a pull-down device. Figure 16-1. MC9S08JM60 Series Block Diagram Highlighting the TPM Blocks and Pins MC9S08JM60 Series Data Sheet, Rev. 3 272 Freescale Semiconductor PORT G PORT F 2-CHANNEL TIMER/PWM Timer/PWM Module (S08TPMV3) 16.1.1 Features The TPM includes these distinctive features: • One to eight channels: — Each channel may be input capture, output compare, or edge-aligned PWM — Rising-Edge, falling-edge, or any-edge input capture trigger — Set, clear, or toggle output compare action — Selectable polarity on PWM outputs • Module may be configured for buffered, center-aligned pulse-width-modulation (CPWM) on all channels • Timer clock source selectable as prescaled bus clock, fixed system clock, or an external clock pin — Prescale taps for divide-by 1, 2, 4, 8, 16, 32, 64, or 128 — Fixed system clock source are synchronized to the bus clock by an on-chip synchronization circuit — External clock pin may be shared with any timer channel pin or a separated input pin • 16-bit free-running or modulo up/down count operation • Timer system enable • One interrupt per channel plus terminal count interrupt 16.1.2 Modes of Operation In general, TPM channels may be independently configured to operate in input capture, output compare, or edge-aligned PWM modes. A control bit allows the whole TPM (all channels) to switch to center-aligned PWM mode. When center-aligned PWM mode is selected, input capture, output compare, and edge-aligned PWM functions are not available on any channels of this TPM module. When the microcontroller is in active BDM background or BDM foreground mode, the TPM temporarily suspends all counting until the microcontroller returns to normal user operating mode. During stop mode, all system clocks, including the main oscillator, are stopped; therefore, the TPM is effectively disabled until clocks resume. During wait mode, the TPM continues to operate normally. Provided the TPM does not need to produce a real time reference or provide the interrupt source(s) needed to wake the MCU from wait mode, the user can save power by disabling TPM functions before entering wait mode. • Input capture mode When a selected edge event occurs on the associated MCU pin, the current value of the 16-bit timer counter is captured into the channel value register and an interrupt flag bit is set. Rising edges, falling edges, any edge, or no edge (disable channel) may be selected as the active edge which triggers the input capture. • Output compare mode When the value in the timer counter register matches the channel value register, an interrupt flag bit is set, and a selected output action is forced on the associated MCU pin. The output compare action may be selected to force the pin to zero, force the pin to one, toggle the pin, or ignore the pin (used for software timing functions). MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 273 Timer/PWM Module (S08TPMV3) • • Edge-aligned PWM mode The value of a 16-bit modulo register plus 1 sets the period of the PWM output signal. The channel value register sets the duty cycle of the PWM output signal. The user may also choose the polarity of the PWM output signal. Interrupts are available at the end of the period and at the duty-cycle transition point. This type of PWM signal is called edge-aligned because the leading edges of all PWM signals are aligned with the beginning of the period, which is the same for all channels within a TPM. Center-aligned PWM mode Twice the value of a 16-bit modulo register sets the period of the PWM output, and the channel-value register sets the half-duty-cycle duration. The timer counter counts up until it reaches the modulo value and then counts down until it reaches zero. As the count matches the channel value register while counting down, the PWM output becomes active. When the count matches the channel value register while counting up, the PWM output becomes inactive. This type of PWM signal is called center-aligned because the centers of the active duty cycle periods for all channels are aligned with a count value of zero. This type of PWM is required for types of motors used in small appliances. This is a high-level description only. Detailed descriptions of operating modes are in later sections. 16.1.3 Block Diagram The TPM uses one input/output (I/O) pin per channel, TPMxCHn (timer channel n) where n is the channel number (1-8). The TPM shares its I/O pins with general purpose I/O port pins (refer to I/O pin descriptions in full-chip specification for the specific chip implementation). Figure 16-2 shows the TPM structure. The central component of the TPM is the 16-bit counter that can operate as a free-running counter or a modulo up/down counter. The TPM counter (when operating in normal up-counting mode) provides the timing reference for the input capture, output compare, and edge-aligned PWM functions. The timer counter modulo registers, TPMxMODH:TPMxMODL, control the modulo value of the counter (the values 0x0000 or 0xFFFF effectively make the counter free running). Software can read the counter value at any time without affecting the counting sequence. Any write to either half of the TPMxCNT counter resets the counter, regardless of the data value written. MC9S08JM60 Series Data Sheet, Rev. 3 274 Freescale Semiconductor Timer/PWM Module (S08TPMV3) BUS CLOCK FIXED SYSTEM CLOCK EXTERNAL CLOCK SYNC CLOCK SOURCE SELECT OFF, BUS, FIXED SYSTEM CLOCK, EXT PRESCALE AND SELECT ³1, 2, 4, 8, 16, 32, 64, or ³128 CLKSB:CLKSA CPWMS 16-BIT COUNTER COUNTER RESET 16-BIT COMPARATOR TPMxMODH:TPMxMODL ELS0B ELS0A PS2:PS1:PS0 TOF TOIE INTERRUPT LOGIC CHANNEL 0 16-BIT COMPARATOR TPMxC0VH:TPMxC0VL 16-BIT LATCH PORT LOGIC CH0F INTERRUPT LOGIC TPMxCH0 MS0B MS0A CH0IE INTERNAL BUS CHANNEL 1 16-BIT COMPARATOR TPMxC1VH:TPMxC1VL 16-BIT LATCH ELS1B ELS1A PORT LOGIC CH1F INTERRUPT LOGIC TPMxCH1 MS1B MS1A CH1IE Up to 8 channels CHANNEL 7 16-BIT COMPARATOR TPMxC7VH:TPMxC7VL 16-BIT LATCH ELS7B ELS7A PORT LOGIC CH7F INTERRUPT LOGIC TPMxCH7 MS7B MS7A CH7IE Figure 16-2. TPM Block Diagram MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 275 Timer/PWM Module (S08TPMV3) The TPM channels are programmable independently as input capture, output compare, or edge-aligned PWM channels. Alternately, the TPM can be configured to produce CPWM outputs on all channels. When the TPM is configured for CPWMs, the counter operates as an up/down counter; input capture, output compare, and EPWM functions are not practical. If a channel is configured as input capture, an internal pullup device may be enabled for that channel. The details of how a module interacts with pin controls depends upon the chip implementation because the I/O pins and associated general purpose I/O controls are not part of the module. Refer to the discussion of the I/O port logic in a full-chip specification. Because center-aligned PWMs are usually used to drive 3-phase AC-induction motors and brushless DC motors, they are typically used in sets of three or six channels. 16.2 Signal Description Table 16-1 shows the user-accessible signals for the TPM. The number of channels may be varied from one to eight. When an external clock is included, it can be shared with the same pin as any TPM channel; however, it could be connected to a separate input pin. Refer to the I/O pin descriptions in full-chip specification for the specific chip implementation. Table 16-1. Signal Properties Name EXTCLK1 TPMxCHn 1 2 Function External clock source which may be selected to drive the TPM counter. I/O pin associated with TPM channel n When preset, this signal can share any channel pin; however depending upon full-chip implementation, this signal could be connected to a separate external pin. 2 n=channel number (1 to 8) Refer to documentation for the full-chip for details about reset states, port connections, and whether there is any pullup device on these pins. TPM channel pins can be associated with general purpose I/O pins and have passive pullup devices which can be enabled with a control bit when the TPM or general purpose I/O controls have configured the associated pin as an input. When no TPM function is enabled to use a corresponding pin, the pin reverts to being controlled by general purpose I/O controls, including the port-data and data-direction registers. Immediately after reset, no TPM functions are enabled, so all associated pins revert to general purpose I/O control. 16.2.1 Detailed Signal Descriptions This section describes each user-accessible pin signal in detail. Although Table 16-1 grouped all channel pins together, any TPM pin can be shared with the external clock source signal. Since I/O pin logic is not part of the TPM, refer to full-chip documentation for a specific derivative for more details about the interaction of TPM pin functions and general purpose I/O controls including port data, data direction, and pullup controls. MC9S08JM60 Series Data Sheet, Rev. 3 276 Freescale Semiconductor Timer/PWM Module (S08TPMV3) 16.2.1.1 EXTCLK — External Clock Source Control bits in the timer status and control register allow the user to select nothing (timer disable), the bus-rate clock (the normal default source), a crystal-related clock, or an external clock as the clock which drives the TPM prescaler and subsequently the 16-bit TPM counter. The external clock source is synchronized in the TPM. The bus clock clocks the synchronizer; the frequency of the external source must be no more than one-fourth the frequency of the bus-rate clock, to meet Nyquist criteria and allowing for jitter. The external clock signal shares the same pin as a channel I/O pin, so the channel pin will not be usable for channel I/O function when selected as the external clock source. It is the user’s responsibility to avoid such settings. If this pin is used as an external clock source (CLKSB:CLKSA = 1:1), the channel can still be used in output compare mode as a software timer (ELSnB:ELSnA = 0:0). 16.2.1.2 TPMxCHn — TPM Channel n I/O Pin(s) Each TPM channel is associated with an I/O pin on the MCU. The function of this pin depends on the channel configuration. The TPM pins share with general purpose I/O pins, where each pin has a port data register bit, and a data direction control bit, and the port has optional passive pullups which may be enabled whenever a port pin is acting as an input. The TPM channel does not control the I/O pin when (ELSnB:ELSnA = 0:0) or when (CLKSB:CLKSA = 0:0) so it normally reverts to general purpose I/O control. When CPWMS = 1 (and ELSnB:ELSnA not = 0:0), all channels within the TPM are configured for center-aligned PWM and the TPMxCHn pins are all controlled by the TPM system. When CPWMS=0, the MSnB:MSnA control bits determine whether the channel is configured for input capture, output compare, or edge-aligned PWM. When a channel is configured for input capture (CPWMS=0, MSnB:MSnA = 0:0 and ELSnB:ELSnA not = 0:0), the TPMxCHn pin is forced to act as an edge-sensitive input to the TPM. ELSnB:ELSnA control bits determine what polarity edge or edges will trigger input-capture events. A synchronizer based on the bus clock is used to synchronize input edges to the bus clock. This implies the minimum pulse width—that can be reliably detected—on an input capture pin is four bus clock periods (with ideal clock pulses as near as two bus clocks can be detected). TPM uses this pin as an input capture input to override the port data and data direction controls for the same pin. When a channel is configured for output compare (CPWMS=0, MSnB:MSnA = 0:1 and ELSnB:ELSnA not = 0:0), the associated data direction control is overridden, the TPMxCHn pin is considered an output controlled by the TPM, and the ELSnB:ELSnA control bits determine how the pin is controlled. The remaining three combinations of ELSnB:ELSnA determine whether the TPMxCHn pin is toggled, cleared, or set each time the 16-bit channel value register matches the timer counter. When the output compare toggle mode is initially selected, the previous value on the pin is driven out until the next output compare event—then the pin is toggled. MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 277 Timer/PWM Module (S08TPMV3) When a channel is configured for edge-aligned PWM (CPWMS=0, MSnB=1 and ELSnB:ELSnA not = 0:0), the data direction is overridden, the TPMxCHn pin is forced to be an output controlled by the TPM, and ELSnA controls the polarity of the PWM output signal on the pin. When ELSnB:ELSnA=1:0, the TPMxCHn pin is forced high at the start of each new period (TPMxCNT=0x0000), and the pin is forced low when the channel value register matches the timer counter. When ELSnA=1, the TPMxCHn pin is forced low at the start of each new period (TPMxCNT=0x0000), and the pin is forced high when the channel value register matches the timer counter. TPMxMODH:TPMxMODL = 0x0008 TPMxCnVH:TPMxCnVL = 0x0005 TPMxCNTH:TPMxCNTL TPMxCHn CHnF BIT TOF BIT ... 0 1 2 3 4 5 6 7 8 0 1 2 ... Figure 16-3. High-True Pulse of an Edge-Aligned PWM TPMxMODH:TPMxMODL = 0x0008 TPMxCnVH:TPMxCnVL = 0x0005 TPMxCNTH:TPMxCNTL TPMxCHn CHnF BIT TOF BIT ... 0 1 2 3 4 5 6 7 8 0 1 2 ... Figure 16-4. Low-True Pulse of an Edge-Aligned PWM MC9S08JM60 Series Data Sheet, Rev. 3 278 Freescale Semiconductor Timer/PWM Module (S08TPMV3) When the TPM is configured for center-aligned PWM (and ELSnB:ELSnA not = 0:0), the data direction for all channels in this TPM are overridden, the TPMxCHn pins are forced to be outputs controlled by the TPM, and the ELSnA bits control the polarity of each TPMxCHn output. If ELSnB:ELSnA=1:0, the corresponding TPMxCHn pin is cleared when the timer counter is counting up, and the channel value register matches the timer counter; the TPMxCHn pin is set when the timer counter is counting down, and the channel value register matches the timer counter. If ELSnA=1, the corresponding TPMxCHn pin is set when the timer counter is counting up and the channel value register matches the timer counter; the TPMxCHn pin is cleared when the timer counter is counting down and the channel value register matches the timer counter. TPMxMODH:TPMxMODL = 0x0008 TPMxCnVH:TPMxCnVL = 0x0005 TPMxCNTH:TPMxCNTL TPMxCHn CHnF BIT TOF BIT ... 7 8 7 6 5 4 3 2 1 0 1 2 3 4 5 6 7 8 7 6 5 ... Figure 16-5. High-True Pulse of a Center-Aligned PWM TPMxMODH:TPMxMODL = 0x0008 TPMxCnVH:TPMxCnVL = 0x0005 TPMxCNTH:TPMxCNTL TPMxCHn CHnF BIT TOF BIT ... 7 8 7 6 5 4 3 2 1 0 1 2 3 4 5 6 7 8 7 6 5 ... Figure 16-6. Low-True Pulse of a Center-Aligned PWM MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 279 Timer/PWM Module (S08TPMV3) 16.3 Register Definition This section consists of register descriptions in address order. A typical MCU system may contain multiple TPMs, and each TPM may have one to eight channels, so register names include placeholder characters to identify which TPM and which channel is being referenced. For example, TPMxCnSC refers to timer (TPM) x, channel n. TPM1C2SC would be the status and control register for channel 2 of timer 1. 16.3.1 TPM Status and Control Register (TPMxSC) TPMxSC contains the overflow status flag and control bits used to configure the interrupt enable, TPM configuration, clock source, and prescale factor. These controls relate to all channels within this timer module. 7 6 5 4 3 2 1 0 R W Reset TOF TOIE 0 0 0 0 0 0 0 0 0 CPWMS CLKSB CLKSA PS2 PS1 PS0 Figure 16-7. TPM Status and Control Register (TPMxSC) Table 16-2. TPMxSC Field Descriptions Field 7 TOF Description Timer overflow flag. This read/write flag is set when the TPM counter resets to 0x0000 after reaching the modulo value programmed in the TPM counter modulo registers. Clear TOF by reading the TPM status and control register when TOF is set and then writing a logic 0 to TOF. If another TPM overflow occurs before the clearing sequence is complete, the sequence is reset so TOF would remain set after the clear sequence was completed for the earlier TOF. This is done so a TOF interrupt request cannot be lost during the clearing sequence for a previous TOF. Reset clears TOF. Writing a logic 1 to TOF has no effect. 0 TPM counter has not reached modulo value or overflow 1 TPM counter has overflowed Timer overflow interrupt enable. This read/write bit enables TPM overflow interrupts. If TOIE is set, an interrupt is generated when TOF equals one. Reset clears TOIE. 0 TOF interrupts inhibited (use for software polling) 1 TOF interrupts enabled Center-aligned PWM select. When present, this read/write bit selects CPWM operating mode. By default, the TPM operates in up-counting mode for input capture, output compare, and edge-aligned PWM functions. Setting CPWMS reconfigures the TPM to operate in up/down counting mode for CPWM functions. Reset clears CPWMS. 0 All channels operate as input capture, output compare, or edge-aligned PWM mode as selected by the MSnB:MSnA control bits in each channel’s status and control register. 1 All channels operate in center-aligned PWM mode. 6 TOIE 5 CPWMS MC9S08JM60 Series Data Sheet, Rev. 3 280 Freescale Semiconductor Timer/PWM Module (S08TPMV3) Table 16-2. TPMxSC Field Descriptions (continued) Field Description 4–3 Clock source selects. As shown in Table 16-3, this 2-bit field is used to disable the TPM system or select one of CLKS[B:A] three clock sources to drive the counter prescaler. The fixed system clock source is only meaningful in systems with a PLL-based system clock. When there is no PLL, the fixed-system clock source is the same as the bus rate clock. The external source is synchronized to the bus clock by TPM module, and the fixed system clock source (when a PLL is present) is synchronized to the bus clock by an on-chip synchronization circuit. When a PLL is present but not enabled, the fixed-system clock source is the same as the bus-rate clock. 2–0 PS[2:0] Prescale factor select. This 3-bit field selects one of 8 division factors for the TPM clock input as shown in Table 16-4. This prescaler is located after any clock source synchronization or clock source selection so it affects the clock source selected to drive the TPM system. The new prescale factor will affect the clock source on the next system clock cycle after the new value is updated into the register bits. Table 16-3. TPM-Clock-Source Selection CLKSB:CLKSA 00 01 10 11 TPM Clock Source to Prescaler Input No clock selected (TPM counter disable) Bus rate clock Fixed system clock External source Table 16-4. Prescale Factor Selection PS2:PS1:PS0 000 001 010 011 100 101 110 111 TPM Clock Source Divided-by 1 2 4 8 16 32 64 128 16.3.2 TPM-Counter Registers (TPMxCNTH:TPMxCNTL) The two read-only TPM counter registers contain the high and low bytes of the value in the TPM counter. Reading either byte (TPMxCNTH or TPMxCNTL) latches the contents of both bytes into a buffer where they remain latched until the other half is read. This allows coherent 16-bit reads in either big-endian or little-endian order which makes this more friendly to various compiler implementations. The coherency mechanism is automatically restarted by an MCU reset or any write to the timer status/control register (TPMxSC). Reset clears the TPM counter registers. Writing any value to TPMxCNTH or TPMxCNTL also clears the TPM counter (TPMxCNTH:TPMxCNTL) and resets the coherency mechanism, regardless of the data involved in the write. MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 281 Timer/PWM Module (S08TPMV3) 7 6 5 4 3 2 1 0 R W Reset Bit 15 14 13 12 11 10 9 Bit 8 Any write to TPMxCNTH clears the 16-bit counter 0 0 0 0 0 0 0 0 Figure 16-8. TPM Counter Register High (TPMxCNTH) 7 6 5 4 3 2 1 0 R W Reset Bit 7 6 5 4 3 2 1 Bit 0 Any write to TPMxCNTL clears the 16-bit counter 0 0 0 0 0 0 0 0 Figure 16-9. TPM Counter Register Low (TPMxCNTL) When BDM is active, the timer counter is frozen (this is the value that will be read by user); the coherency mechanism is frozen such that the buffer latches remain in the state they were in when the BDM became active, even if one or both counter halves are read while BDM is active. This assures that if the user was in the middle of reading a 16-bit register when BDM became active, it will read the appropriate value from the other half of the 16-bit value after returning to normal execution. In BDM mode, writing any value to TPMxSC, TPMxCNTH or TPMxCNTL registers resets the read coherency mechanism of the TPMxCNTH:L registers, regardless of the data involved in the write. 16.3.3 TPM Counter Modulo Registers (TPMxMODH:TPMxMODL) The read/write TPM modulo registers contain the modulo value for the TPM counter. After the TPM counter reaches the modulo value, the TPM counter resumes counting from 0x0000 at the next clock, and the overflow flag (TOF) becomes set. Writing to TPMxMODH or TPMxMODL inhibits the TOF bit and overflow interrupts until the other byte is written. Reset sets the TPM counter modulo registers to 0x0000 which results in a free running timer counter (modulo disabled). Writing to either byte (TPMxMODH or TPMxMODL) latches the value into a buffer and the registers are updated with the value of their write buffer according to the value of CLKSB:CLKSA bits, so: • If (CLKSB:CLKSA = 0:0), then the registers are updated when the second byte is written • If (CLKSB:CLKSA not = 0:0), then the registers are updated after both bytes were written, and the TPM counter changes from (TPMxMODH:TPMxMODL - 1) to (TPMxMODH:TPMxMODL). If the TPM counter is a free-running counter, the update is made when the TPM counter changes from 0xFFFE to 0xFFFF The latching mechanism may be manually reset by writing to the TPMxSC address (whether BDM is active or not). When BDM is active, the coherency mechanism is frozen (unless reset by writing to TPMxSC register) such that the buffer latches remain in the state they were in when the BDM became active, even if one or both halves of the modulo register are written while BDM is active. Any write to the modulo registers bypasses the buffer latches and directly writes to the modulo register while BDM is active. MC9S08JM60 Series Data Sheet, Rev. 3 282 Freescale Semiconductor Timer/PWM Module (S08TPMV3) 7 6 5 4 3 2 1 0 R Bit 15 W Reset 0 0 0 0 0 0 0 0 14 13 12 11 10 9 Bit 8 Figure 16-10. TPM Counter Modulo Register High (TPMxMODH) 7 6 5 4 3 2 1 0 R Bit 7 W Reset 0 0 0 0 0 0 0 0 6 5 4 3 2 1 Bit 0 Figure 16-11. TPM Counter Modulo Register Low (TPMxMODL) Reset the TPM counter before writing to the TPM modulo registers to avoid confusion about when the first counter overflow will occur. 16.3.4 TPM Channel n Status and Control Register (TPMxCnSC) TPMxCnSC contains the channel-interrupt-status flag and control bits used to configure the interrupt enable, channel configuration, and pin function. 7 6 5 4 3 2 1 0 R W Reset CHnF CHnIE 0 0 0 0 0 0 0 MSnB MSnA ELSnB ELSnA 0 0 0 0 = Unimplemented or Reserved Figure 16-12. TPM Channel n Status and Control Register (TPMxCnSC) MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 283 Timer/PWM Module (S08TPMV3) Table 16-5. TPMxCnSC Field Descriptions Field 7 CHnF Description Channel n flag. When channel n is an input-capture channel, this read/write bit is set when an active edge occurs on the channel n pin. When channel n is an output compare or edge-aligned/center-aligned PWM channel, CHnF is set when the value in the TPM counter registers matches the value in the TPM channel n value registers. When channel n is an edge-aligned/center-aligned PWM channel and the duty cycle is set to 0% or 100%, CHnF will not be set even when the value in the TPM counter registers matches the value in the TPM channel n value registers. A corresponding interrupt is requested when CHnF is set and interrupts are enabled (CHnIE = 1). Clear CHnF by reading TPMxCnSC while CHnF is set and then writing a logic 0 to CHnF. If another interrupt request occurs before the clearing sequence is complete, the sequence is reset so CHnF remains set after the clear sequence completed for the earlier CHnF. This is done so a CHnF interrupt request cannot be lost due to clearing a previous CHnF. Reset clears the CHnF bit. Writing a logic 1 to CHnF has no effect. 0 No input capture or output compare event occurred on channel n 1 Input capture or output compare event on channel n Channel n interrupt enable. This read/write bit enables interrupts from channel n. Reset clears CHnIE. 0 Channel n interrupt requests disabled (use for software polling) 1 Channel n interrupt requests enabled Mode select B for TPM channel n. When CPWMS=0, MSnB=1 configures TPM channel n for edge-aligned PWM mode. Refer to the summary of channel mode and setup controls in Table 16-6. Mode select A for TPM channel n. When CPWMS=0 and MSnB=0, MSnA configures TPM channel n for input-capture mode or output compare mode. Refer to Table 16-6 for a summary of channel mode and setup controls. Note: If the associated port pin is not stable for at least two bus clock cycles before changing to input capture mode, it is possible to get an unexpected indication of an edge trigger. Edge/level select bits. Depending upon the operating mode for the timer channel as set by CPWMS:MSnB:MSnA and shown in Table 16-6, these bits select the polarity of the input edge that triggers an input capture event, select the level that will be driven in response to an output compare match, or select the polarity of the PWM output. Setting ELSnB:ELSnA to 0:0 configures the related timer pin as a general purpose I/O pin not related to any timer functions. This function is typically used to temporarily disable an input capture channel or to make the timer pin available as a general purpose I/O pin when the associated timer channel is set up as a software timer that does not require the use of a pin. 6 CHnIE 5 MSnB 4 MSnA 3–2 ELSnB ELSnA MC9S08JM60 Series Data Sheet, Rev. 3 284 Freescale Semiconductor Timer/PWM Module (S08TPMV3) Table 16-6. Mode, Edge, and Level Selection CPWMS X 0 MSnB:MSnA XX 00 ELSnB:ELSnA 00 01 10 11 01 01 10 11 1X 10 X1 1 XX 10 X1 Center-aligned PWM Edge-aligned PWM Output compare Mode Configuration Pin not used for TPM - revert to general purpose I/O or other peripheral control Input capture Capture on rising edge only Capture on falling edge only Capture on rising or falling edge Toggle output on compare Clear output on compare Set output on compare High-true pulses (clear output on compare) Low-true pulses (set output on compare) High-true pulses (clear output on compare-up) Low-true pulses (set output on compare-up) 16.3.5 TPM Channel Value Registers (TPMxCnVH:TPMxCnVL) These read/write registers contain the captured TPM counter value of the input capture function or the output compare value for the output compare or PWM functions. The channel registers are cleared by reset. 7 6 5 4 3 2 1 0 R Bit 15 W Reset 0 0 0 0 0 0 0 0 14 13 12 11 10 9 Bit 8 Figure 16-13. TPM Channel Value Register High (TPMxCnVH) 7 6 5 4 3 2 1 0 R Bit 7 W Reset 0 0 0 0 0 0 0 0 6 5 4 3 2 1 Bit 0 Figure 16-14. TPM Channel Value Register Low (TPMxCnVL) MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 285 Timer/PWM Module (S08TPMV3) In input capture mode, reading either byte (TPMxCnVH or TPMxCnVL) latches the contents of both bytes into a buffer where they remain latched until the other half is read. This latching mechanism also resets (becomes unlatched) when the TPMxCnSC register is written (whether BDM mode is active or not). Any write to the channel registers will be ignored during the input capture mode. When BDM is active, the coherency mechanism is frozen (unless reset by writing to TPMxCnSC register) such that the buffer latches remain in the state they were in when the BDM became active, even if one or both halves of the channel register are read while BDM is active. This assures that if the user was in the middle of reading a 16-bit register when BDM became active, it will read the appropriate value from the other half of the 16-bit value after returning to normal execution. The value read from the TPMxCnVH and TPMxCnVL registers in BDM mode is the value of these registers and not the value of their read buffer. In output compare or PWM modes, writing to either byte (TPMxCnVH or TPMxCnVL) latches the value into a buffer. After both bytes are written, they are transferred as a coherent 16-bit value into the timer-channel registers according to the value of CLKSB:CLKSA bits and the selected mode, so: • If (CLKSB:CLKSA = 0:0), then the registers are updated when the second byte is written. • If (CLKSB:CLKSA not = 0:0 and in output compare mode) then the registers are updated after the second byte is written and on the next change of the TPM counter (end of the prescaler counting). • If (CLKSB:CLKSA not = 0:0 and in EPWM or CPWM modes), then the registers are updated after the both bytes were written, and the TPM counter changes from (TPMxMODH:TPMxMODL - 1) to (TPMxMODH:TPMxMODL). If the TPM counter is a free-running counter then the update is made when the TPM counter changes from 0xFFFE to 0xFFFF. The latching mechanism may be manually reset by writing to the TPMxCnSC register (whether BDM mode is active or not). This latching mechanism allows coherent 16-bit writes in either big-endian or little-endian order which is friendly to various compiler implementations. When BDM is active, the coherency mechanism is frozen such that the buffer latches remain in the state they were in when the BDM became active even if one or both halves of the channel register are written while BDM is active. Any write to the channel registers bypasses the buffer latches and directly write to the channel register while BDM is active. The values written to the channel register while BDM is active are used for PWM & output compare operation once normal execution resumes. Writes to the channel registers while BDM is active do not interfere with partial completion of a coherency sequence. After the coherency mechanism has been fully exercised, the channel registers are updated using the buffered values written (while BDM was not active) by the user. 16.4 Functional Description All TPM functions are associated with a central 16-bit counter which allows flexible selection of the clock source and prescale factor. There is also a 16-bit modulo register associated with the main counter. The CPWMS control bit chooses between center-aligned PWM operation for all channels in the TPM (CPWMS=1) or general purpose timing functions (CPWMS=0) where each channel can independently be configured to operate in input capture, output compare, or edge-aligned PWM mode. The CPWMS control bit is located in the main TPM status and control register because it affects all channels within the TPM MC9S08JM60 Series Data Sheet, Rev. 3 286 Freescale Semiconductor Timer/PWM Module (S08TPMV3) and influences the way the main counter operates. (In CPWM mode, the counter changes to an up/down mode rather than the up-counting mode used for general purpose timer functions.) The following sections describe the main counter and each of the timer operating modes (input capture, output compare, edge-aligned PWM, and center-aligned PWM). Because details of pin operation and interrupt activity depend upon the operating mode, these topics will be covered in the associated mode explanation sections. 16.4.1 Counter All timer functions are based on the main 16-bit counter (TPMxCNTH:TPMxCNTL). This section discusses selection of the clock source, end-of-count overflow, up-counting vs. up/down counting, and manual counter reset. 16.4.1.1 Counter Clock Source The 2-bit field, CLKSB:CLKSA, in the timer status and control register (TPMxSC) selects one of three possible clock sources or OFF (which effectively disables the TPM). See Table 16-3. After any MCU reset, CLKSB:CLKSA=0:0 so no clock source is selected, and the TPM is in a very low power state. These control bits may be read or written at any time and disabling the timer (writing 00 to the CLKSB:CLKSA field) does not affect the values in the counter or other timer registers. Table 16-7. TPM Clock Source Selection CLKSB:CLKSA 00 01 10 11 TPM Clock Source to Prescaler Input No clock selected (TPM counter disabled) Bus rate clock Fixed system clock External source The bus rate clock is the main system bus clock for the MCU. This clock source requires no synchronization because it is the clock that is used for all internal MCU activities including operation of the CPU and buses. In MCUs that have no PLL or the PLL is not engaged, the fixed system clock source is the same as the bus-rate-clock source, and it does not go through a synchronizer. When a PLL is present and engaged, a synchronizer is required between the crystal divided-by two clock source and the timer counter so counter transitions will be properly aligned to bus-clock transitions. A synchronizer will be used at chip level to synchronize the crystal-related source clock to the bus clock. The external clock source may be connected to any TPM channel pin. This clock source always has to pass through a synchronizer to assure that counter transitions are properly aligned to bus clock transitions. The bus-rate clock drives the synchronizer; therefore, to meet Nyquist criteria even with jitter, the frequency of the external clock source must not be faster than the bus rate divided-by four. With ideal clocks the external clock can be as fast as bus clock divided by four. MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 287 Timer/PWM Module (S08TPMV3) When the external clock source shares the TPM channel pin, this pin should not be used for other channel timing functions. For example, it would be ambiguous to configure channel 0 for input capture when the TPM channel 0 pin was also being used as the timer external clock source. (It is the user’s responsibility to avoid such settings.) The TPM channel could still be used in output compare mode for software timing functions (pin controls set not to affect the TPM channel pin). 16.4.1.2 Counter Overflow and Modulo Reset An interrupt flag and enable are associated with the 16-bit main counter. The flag (TOF) is a software-accessible indication that the timer counter has overflowed. The enable signal selects between software polling (TOIE=0) where no hardware interrupt is generated, or interrupt-driven operation (TOIE=1) where a static hardware interrupt is generated whenever the TOF flag is equal to one. The conditions causing TOF to become set depend on whether the TPM is configured for center-aligned PWM (CPWMS=1). In the simplest mode, there is no modulus limit and the TPM is not in CPWMS=1 mode. In this case, the 16-bit timer counter counts from 0x0000 through 0xFFFF and overflows to 0x0000 on the next counting clock. TOF becomes set at the transition from 0xFFFF to 0x0000. When a modulus limit is set, TOF becomes set at the transition from the value set in the modulus register to 0x0000. When the TPM is in center-aligned PWM mode (CPWMS=1), the TOF flag gets set as the counter changes direction at the end of the count value set in the modulus register (that is, at the transition from the value set in the modulus register to the next lower count value). This corresponds to the end of a PWM period (the 0x0000 count value corresponds to the center of a period). 16.4.1.3 Counting Modes The main timer counter has two counting modes. When center-aligned PWM is selected (CPWMS=1), the counter operates in up/down counting mode. Otherwise, the counter operates as a simple up counter. As an up counter, the timer counter counts from 0x0000 through its terminal count and then continues with 0x0000. The terminal count is 0xFFFF or a modulus value in TPMxMODH:TPMxMODL. When center-aligned PWM operation is specified, the counter counts up from 0x0000 through its terminal count and then down to 0x0000 where it changes back to up counting. Both 0x0000 and the terminal count value are normal length counts (one timer clock period long). In this mode, the timer overflow flag (TOF) becomes set at the end of the terminal-count period (as the count changes to the next lower count value). 16.4.1.4 Manual Counter Reset The main timer counter can be manually reset at any time by writing any value to either half of TPMxCNTH or TPMxCNTL. Resetting the counter in this manner also resets the coherency mechanism in case only half of the counter was read before resetting the count. 16.4.2 Channel Mode Selection Provided CPWMS=0, the MSnB and MSnA control bits in the channel n status and control registers determine the basic mode of operation for the corresponding channel. Choices include input capture, output compare, and edge-aligned PWM. MC9S08JM60 Series Data Sheet, Rev. 3 288 Freescale Semiconductor Timer/PWM Module (S08TPMV3) 16.4.2.1 Input Capture Mode With the input-capture function, the TPM can capture the time at which an external event occurs. When an active edge occurs on the pin of an input-capture channel, the TPM latches the contents of the TPM counter into the channel-value registers (TPMxCnVH:TPMxCnVL). Rising edges, falling edges, or any edge may be chosen as the active edge that triggers an input capture. In input capture mode, the TPMxCnVH and TPMxCnVL registers are read only. When either half of the 16-bit capture register is read, the other half is latched into a buffer to support coherent 16-bit accesses in big-endian or little-endian order. The coherency sequence can be manually reset by writing to the channel status/control register (TPMxCnSC). An input capture event sets a flag bit (CHnF) which may optionally generate a CPU interrupt request. While in BDM, the input capture function works as configured by the user. When an external event occurs, the TPM latches the contents of the TPM counter (which is frozen because of the BDM mode) into the channel value registers and sets the flag bit. 16.4.2.2 Output Compare Mode With the output-compare function, the TPM can generate timed pulses with programmable position, polarity, duration, and frequency. When the counter reaches the value in the channel-value registers of an output-compare channel, the TPM can set, clear, or toggle the channel pin. In output compare mode, values are transferred to the corresponding timer channel registers only after both 8-bit halves of a 16-bit register have been written and according to the value of CLKSB:CLKSA bits, so: • If (CLKSB:CLKSA = 0:0), the registers are updated when the second byte is written • If (CLKSB:CLKSA not = 0:0), the registers are updated at the next change of the TPM counter (end of the prescaler counting) after the second byte is written. The coherency sequence can be manually reset by writing to the channel status/control register (TPMxCnSC). An output compare event sets a flag bit (CHnF) which may optionally generate a CPU-interrupt request. 16.4.2.3 Edge-Aligned PWM Mode This type of PWM output uses the normal up-counting mode of the timer counter (CPWMS=0) and can be used when other channels in the same TPM are configured for input capture or output compare functions. The period of this PWM signal is determined by the value of the modulus register (TPMxMODH:TPMxMODL) plus 1. The duty cycle is determined by the setting in the timer channel register (TPMxCnVH:TPMxCnVL). The polarity of this PWM signal is determined by the setting in the ELSnA control bit. 0% and 100% duty cycle cases are possible. The output compare value in the TPM channel registers determines the pulse width (duty cycle) of the PWM signal (Figure 16-15). The time between the modulus overflow and the output compare is the pulse width. If ELSnA=0, the counter overflow forces the PWM signal high, and the output compare forces the PWM signal low. If ELSnA=1, the counter overflow forces the PWM signal low, and the output compare forces the PWM signal high. MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 289 Timer/PWM Module (S08TPMV3) OVERFLOW PERIOD PULSE WIDTH TPMxCHn OVERFLOW OVERFLOW OUTPUT COMPARE OUTPUT COMPARE OUTPUT COMPARE Figure 16-15. PWM Period and Pulse Width (ELSnA=0) When the channel value register is set to 0x0000, the duty cycle is 0%. 100% duty cycle can be achieved by setting the timer-channel register (TPMxCnVH:TPMxCnVL) to a value greater than the modulus setting. This implies that the modulus setting must be less than 0xFFFF in order to get 100% duty cycle. Because the TPM may be used in an 8-bit MCU, the settings in the timer channel registers are buffered to ensure coherent 16-bit updates and to avoid unexpected PWM pulse widths. Writes to any of the registers TPMxCnVH and TPMxCnVL, actually write to buffer registers. In edge-aligned PWM mode, values are transferred to the corresponding timer-channel registers according to the value of CLKSB:CLKSA bits, so: • If (CLKSB:CLKSA = 0:0), the registers are updated when the second byte is written • If (CLKSB:CLKSA not = 0:0), the registers are updated after the both bytes were written, and the TPM counter changes from (TPMxMODH:TPMxMODL - 1) to (TPMxMODH:TPMxMODL). If the TPM counter is a free-running counter then the update is made when the TPM counter changes from 0xFFFE to 0xFFFF. 16.4.2.4 Center-Aligned PWM Mode This type of PWM output uses the up/down counting mode of the timer counter (CPWMS=1). The output compare value in TPMxCnVH:TPMxCnVL determines the pulse width (duty cycle) of the PWM signal while the period is determined by the value in TPMxMODH:TPMxMODL. TPMxMODH:TPMxMODL should be kept in the range of 0x0001 to 0x7FFF because values outside this range can produce ambiguous results. ELSnA will determine the polarity of the CPWM output. pulse width = 2 x (TPMxCnVH:TPMxCnVL) period = 2 x (TPMxMODH:TPMxMODL); TPMxMODH:TPMxMODL=0x0001-0x7FFF If the channel-value register TPMxCnVH:TPMxCnVL is zero or negative (bit 15 set), the duty cycle will be 0%. If TPMxCnVH:TPMxCnVL is a positive value (bit 15 clear) and is greater than the (non-zero) modulus setting, the duty cycle will be 100% because the duty cycle compare will never occur. This implies the usable range of periods set by the modulus register is 0x0001 through 0x7FFE (0x7FFF if you do not need to generate 100% duty cycle). This is not a significant limitation. The resulting period would be much longer than required for normal applications. TPMxMODH:TPMxMODL=0x0000 is a special case that should not be used with center-aligned PWM mode. When CPWMS=0, this case corresponds to the counter running free from 0x0000 through 0xFFFF, but when CPWMS=1 the counter needs a valid match to the modulus register somewhere other than at 0x0000 in order to change directions from up-counting to down-counting. MC9S08JM60 Series Data Sheet, Rev. 3 290 Freescale Semiconductor Timer/PWM Module (S08TPMV3) The output compare value in the TPM channel registers (times 2) determines the pulse width (duty cycle) of the CPWM signal (Figure 16-16). If ELSnA=0, a compare occurred while counting up forces the CPWM output signal low and a compare occurred while counting down forces the output high. The counter counts up until it reaches the modulo setting in TPMxMODH:TPMxMODL, then counts down until it reaches zero. This sets the period equal to two times TPMxMODH:TPMxMODL. COUNT= 0 OUTPUT COUNT= COMPARE TPMxMODH:TPMxMODL (COUNT DOWN) OUTPUT COMPARE (COUNT UP) COUNT= TPMxMODH:TPMxMODL TPMxCHn PULSE WIDTH 2 x TPMxCnVH:TPMxCnVL PERIOD 2 x TPMxMODH:TPMxMODL Figure 16-16. CPWM Period and Pulse Width (ELSnA=0) Center-aligned PWM outputs typically produce less noise than edge-aligned PWMs because fewer I/O pin transitions are lined up at the same system clock edge. This type of PWM is also required for some types of motor drives. Input capture, output compare, and edge-aligned PWM functions do not make sense when the counter is operating in up/down counting mode so this implies that all active channels within a TPM must be used in CPWM mode when CPWMS=1. The TPM may be used in an 8-bit MCU. The settings in the timer channel registers are buffered to ensure coherent 16-bit updates and to avoid unexpected PWM pulse widths. Writes to any of the registers TPMxMODH, TPMxMODL, TPMxCnVH, and TPMxCnVL, actually write to buffer registers. In center-aligned PWM mode, the TPMxCnVH:L registers are updated with the value of their write buffer according to the value of CLKSB:CLKSA bits, so: • If (CLKSB:CLKSA = 0:0), the registers are updated when the second byte is written • If (CLKSB:CLKSA not = 0:0), the registers are updated after the both bytes were written, and the TPM counter changes from (TPMxMODH:TPMxMODL - 1) to (TPMxMODH:TPMxMODL). If the TPM counter is a free-running counter, the update is made when the TPM counter changes from 0xFFFE to 0xFFFF. When TPMxCNTH:TPMxCNTL=TPMxMODH:TPMxMODL, the TPM can optionally generate a TOF interrupt (at the end of this count). Writing to TPMxSC cancels any values written to TPMxMODH and/or TPMxMODL and resets the coherency mechanism for the modulo registers. Writing to TPMxCnSC cancels any values written to the channel value registers and resets the coherency mechanism for TPMxCnVH:TPMxCnVL. MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 291 Timer/PWM Module (S08TPMV3) 16.5 16.5.1 Reset Overview General The TPM is reset whenever any MCU reset occurs. 16.5.2 Description of Reset Operation Reset clears the TPMxSC register which disables clocks to the TPM and disables timer overflow interrupts (TOIE=0). CPWMS, MSnB, MSnA, ELSnB, and ELSnA are all cleared which configures all TPM channels for input-capture operation with the associated pins disconnected from I/O pin logic (so all MCU pins related to the TPM revert to general purpose I/O pins). 16.6 16.6.1 Interrupts General The TPM generates an optional interrupt for the main counter overflow and an interrupt for each channel. The meaning of channel interrupts depends on each channel’s mode of operation. If the channel is configured for input capture, the interrupt flag is set each time the selected input capture edge is recognized. If the channel is configured for output compare or PWM modes, the interrupt flag is set each time the main timer counter matches the value in the 16-bit channel value register. All TPM interrupts are listed in Table 16-8 which shows the interrupt name, the name of any local enable that can block the interrupt request from leaving the TPM and getting recognized by the separate interrupt processing logic. Table 16-8. Interrupt Summary Interrupt TOF Local Enable TOIE Source Counter overflow Description Set each time the timer counter reaches its terminal count (at transition to next count value which is usually 0x0000) An input capture or output compare event took place on channel n CHnF CHnIE Channel event The TPM module will provide a high-true interrupt signal. Vectors and priorities are determined at chip integration time in the interrupt module so refer to the user’s guide for the interrupt module or to the chip’s complete documentation for details. 16.6.2 Description of Interrupt Operation For each interrupt source in the TPM, a flag bit is set upon recognition of the interrupt condition such as timer overflow, channel-input capture, or output-compare events. This flag may be read (polled) by software to determine that the action has occurred, or an associated enable bit (TOIE or CHnIE) can be set MC9S08JM60 Series Data Sheet, Rev. 3 292 Freescale Semiconductor Timer/PWM Module (S08TPMV3) to enable hardware interrupt generation. While the interrupt enable bit is set, a static interrupt will generate whenever the associated interrupt flag equals one. The user’s software must perform a sequence of steps to clear the interrupt flag before returning from the interrupt-service routine. TPM interrupt flags are cleared by a two-step process including a read of the flag bit while it is set (1) followed by a write of zero (0) to the bit. If a new event is detected between these two steps, the sequence is reset and the interrupt flag remains set after the second step to avoid the possibility of missing the new event. 16.6.2.1 Timer Overflow Interrupt (TOF) Description The meaning and details of operation for TOF interrupts varies slightly depending upon the mode of operation of the TPM system (general purpose timing functions versus center-aligned PWM operation). The flag is cleared by the two step sequence described above. 16.6.2.1.1 Normal Case Normally TOF is set when the timer counter changes from 0xFFFF to 0x0000. When the TPM is not configured for center-aligned PWM (CPWMS=0), TOF gets set when the timer counter changes from the terminal count (the value in the modulo register) to 0x0000. This case corresponds to the normal meaning of counter overflow. 16.6.2.1.2 Center-Aligned PWM Case When CPWMS=1, TOF gets set when the timer counter changes direction from up-counting to down-counting at the end of the terminal count (the value in the modulo register). In this case the TOF corresponds to the end of a PWM period. 16.6.2.2 Channel Event Interrupt Description The meaning of channel interrupts depends on the channel’s current mode (input-capture, output-compare, edge-aligned PWM, or center-aligned PWM). 16.6.2.2.1 Input Capture Events When a channel is configured as an input capture channel, the ELSnB:ELSnA control bits select no edge (off), rising edges, falling edges or any edge as the edge which triggers an input capture event. When the selected edge is detected, the interrupt flag is set. The flag is cleared by the two-step sequence described in Section 16.6.2, “Description of Interrupt Operation.” 16.6.2.2.2 Output Compare Events When a channel is configured as an output compare channel, the interrupt flag is set each time the main timer counter matches the 16-bit value in the channel value register. The flag is cleared by the two-step sequence described Section 16.6.2, “Description of Interrupt Operation.” MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 293 Timer/PWM Module (S08TPMV3) 16.6.2.2.3 PWM End-of-Duty-Cycle Events For channels configured for PWM operation there are two possibilities. When the channel is configured for edge-aligned PWM, the channel flag gets set when the timer counter matches the channel value register which marks the end of the active duty cycle period. When the channel is configured for center-aligned PWM, the timer count matches the channel value register twice during each PWM cycle. In this CPWM case, the channel flag is set at the start and at the end of the active duty cycle period which are the times when the timer counter matches the channel value register. The flag is cleared by the two-step sequence described Section 16.6.2, “Description of Interrupt Operation.” MC9S08JM60 Series Data Sheet, Rev. 3 294 Freescale Semiconductor Chapter 17 Universal Serial Bus Device Controller (S08USBV1) 17.1 Introduction This chapter describes an universal serial bus device controller (S08USBV1) module that is based on the Universal Serial Bus Specification Rev 2.0. The USB bus is designed to replace existing bus interfaces such as RS-232, PS/2, and IEEE 1284 for PC peripherals. The S08USBV1 module provides a single-chip solution for full-speed (12 Mbps) USB device applications, and integrates the required transceiver with Serial Interface Engine (SIE), 3.3 V regualtor, Endpoint RAM and other control logics. 17.1.1 Clocking Requirements The S08USBV1 requires two clock sources, the 24 MHz bus clock and a 48 MHz reference clock. The 48 MHz clock is sourced directly from MCGOUT. To achieve the 48 MHz clock rate, the MCG must be configured properly for PLL engaged external (PEE) mode with an external crystal. For USB operation, examples of MCG configuration using PEE mode include: • 2 MHz crystal – RDIV = 000 and VDIV = 0110 • 4 MHz crystal – RDIV = 001 and VDIV = 0110 17.1.2 Current Consumption in USB Suspend In USB suspend mode, the USB device current consumption is limited to 500 μA. When the USB device goes into suspend mode, the firmware typically enters stop3 to meet the USB suspend requirements on current consumption. NOTE Enabling LVD increases current consumption in stop3. Consequently, when trying to satisfy USB suspend requirements, disabling LVD before entering stop3. 17.1.3 3.3 V Regulator If using an external 3.3 V regulator as an input to VUSB33 (only when USBVREN = 0), the supply voltage, VDD, must not fall below the input voltage at the VUSB33 pin. If using the internal 3.3 V regulator (USBVREN = 1), do not connect an external supply to the VUSB33 pin. In this case, VDD must fall between 3.9 V and 5.5 V for the internal 3.3 V regulator to operate correctly. MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 295 Chapter 17 Universal Serial Bus Device Controller (S08USBV1) Table 17-1. USBVREN Configuration USBVREN 0 1 3.3-V Regulator External 3.3-V Regulator (as input to VUSB33 pin) Internal 3.3-V Regulator (no external supply connected to VUSB33 pin) VDD Supply Voltage Range VUSB33 ≤ VDD Supply Voltage 3.9 V ≤ VDD Supply Voltage ≤ 5.5V MC9S08JM60 Series Data Sheet, Rev. 3 296 Freescale Semiconductor Chapter 17 Universal Serial Bus Device Controller (S08USBV1) USBDP USBDN PORT A 6 PTA5– PTA0 PTB7/ADP7 PTB6/ADP6 PTB5/KBIP5/ADP5 PTB4/KBIP4/ADP4 PTB3/SS2/ADP3 PTB2/SPSCK2/ADP2 PTB1/MOSI2/ADP1 PTB0/MISO2/ADP0 PTC6 PTC5/RxD2 PTC4 PTC3/TxD2 PTC2 PTC1/SDA PTC0/SCL HCS08 CORE On Chip ICE AND DEBUG MODULE (DBG) USB SIE FULL SPEED USB ENDPOINT RAM USB TRANSCEIVER BKGD/MS BDC CPU RESET HCS08 SYSTEM CONTROL RESETS AND INTERRUPTS MODES OF OPERATION POWER MANAGEMENT 8-/16-BIT SERIAL PERIPHERAL INTERFACE MODULE (SPI2) SS2 SPSCK2 MOSI2 MISO2 RxD2 TxD2 SDA SCL IRQ/TPMCLK SERIAL COMMUNICATIONS INTERFACE MODULE (SCI2) COP IRQ LVD IIC MODULE (IIC) VDDAD VSSAD VREFL VREFH USER Flash (IN BYTES) MC9S08JM60 = 60,912 MC9S08JM32 = 32,768 12-CHANNEL, 12-BIT ANALOG-TO-DIGITAL CONVERTER (ADC) 8 4 PORT D PORT C PORT B ACMP– ANALOG COMPARATOR (ACMP) ACMP+ ACMPO SS1 SPSCK1 MOSI1 MISO1 6-CHANNEL TIMER/PWM MODULE (TPM1) SERIAL COMMUNICATIONS INTERFACE MODULE (SCI1) PORT E TPMCLK TPM1CH1 TPM1CH0 TPM1CHx 4 RxD1 TxD1 TPMCLK TPM2CH1 TPM2CH0 KBIPx 8-BIT KEYBOARD INTERRUPT MODULE (KBI) KBIPx EXTAL XTAL PTD7 PTD6 PTD5 PTD4/ADP11 PTD3/KBIP3/ADP10 PTD2/KBIP2/ACMPO PTD1/ADP9/ACMP– PTD0/ADP8/ACMP+ PTE7/SS1 PTE6/SPSCK1 PTE5/MOSI1 PTE4/MISO1 PTE3/TPM1CH1 PTE2/TPM1CH0 PTE1/RxD1 PTE0/TxD1 PTF7 PTF6 PTF5/TPM2CH1 PTF4/TPM2CH0 PTF3/TPM1CH5 PTF2/TPM1CH4 PTF1/TPM1CH3 PTF0/TPM1CH2 PTG5/EXTAL PTG4/XTAL PTG3/KBIP7 PTG2/KBIP6 PTG1/KBIP1 PTG0/KBIP0 USER RAM (IN BYTES) MC9S08JM60 = 4096 MC9S08JM32 = 2048 8-/16-BIT SERIAL PERIPHERAL INTERFACE MODULE (SPI1) MULTI-PURPOSE CLOCK GENERATOR (MCG) VSSOSC LOW-POWER OSCILLATOR SYSTEM VOLTAGE REGULATOR USB 3.3 V VOLTAGE REGULATOR REAL-TIME COUNTER (RTC) VDD VSS MODULE (TPM2) VUSB33 4 4 NOTES: 1. Port pins are software configurable with pullup device if input port. 2. Pin contains software configurable pullup/pull-down device ifpullup IRQ is enabled (IRQPE = 1). Pull-down is enabled if rising edge detect is selected (IRQEDG = 1) 3. IRQ does not have a clamp diode to VDD. IRQ must not be driven above VDD. 4. Pin contains integrated pullup device. 5. When pin functions as KBI (KBIPEn = 1) and associated pin is configured to enable the pullup device, KBEDGn can be used to reconfigure the pullup as a pull-down device. Figure 17-1. MC9S08JM60 Series Block Diagram Highlighting USB Blocks and Pins MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 297 PORT G PORT F 2-CHANNEL TIMER/PWM Universal Serial Bus Device Controller (S08USBV1) 17.1.4 Features Features of the USB module include: • USB 2.0 compliant — 12 Mbps full-speed (FS) data rate — USB data control logic: – Packet identification and decoding/generation – CRC generation and checking – NRZI (non-return-to-zero inverted) encoding/decoding – Bit-stuffing – Sync detection – End-of-packet detection • Seven USB endpoints — Bidirectional endpoint 0 — Six unidirectional data endpoints configurable as interrupt, bulk, or isochronous — Endpoints 5 and 6 support double-buffering • USB RAM — 256 bytes of buffer RAM shared between system and USB module — RAM may be allocated as buffers for USB controller or extra system RAM resource • USB reset options — USB module reset generated by MCU — Bus reset generated by the host, which triggers a CPU interrupt • Suspend and resume operations with remote wakeup support • Transceiver features — Converts USB differential voltages to digital logic signal levels • On-chip USB pullup resistor • On-chip 3.3-V regulator 17.1.5 Mode Stop1 Stop2 Modes of Operation Table 17-2. Operating Modes Description USB module is not functional. Before entering stop1, the internal USB voltage regulator and USB transceiver enter shutdown mode; therefore, the USB voltage regulator and USB transceiver must be disabled by firmware. USB module is not functional. Before entering stop2, the internal USB voltage regulator and USB transceiver enter shutdown mode; therefore, the USB voltage regulator and USB transceiver must be disabled by firmware. MC9S08JM60 Series Data Sheet, Rev. 3 298 Freescale Semiconductor Universal Serial Bus Device Controller (S08USBV1) Table 17-2. Operating Modes (continued) Mode Stop3 Description The USB module is optionally available in stop3. A reduced current consumption mode may be required for USB suspend mode per USB Specification Rev. 2.0, and stop3 mode is useful for achieving lower current consumption for the MCU and hence the overall USB device. Before entering stop3 via firmware, the user must ensure that the device settings are configured for stop3 to achieve USB suspend current consumption targets. The USB module is notified about entering suspend mode when the SLEEPF flag is set; this occurs after the USB bus is idle for 3 ms. The device USB suspend mode current consumption level requirements are defined by the USB Specification Rev. 2.0 (500 μA for low-power and 2.5 mA for high-power with remote-wakeup enabled). If USBRESMEN in USBCTL0 is set, and a K-state (resume signaling) is detected on the USB bus, the LPRESF bit in USBCTL0 will be set. This triggers an asynchronous interrupt that will wakeup the MCU from stop3 mode and enable clocks to the USB module. The USBRESMEN bit must then be cleared immediately after stop3 recovery to clear the LPRESF flag bit. USB module is operational. Wait 17.1.6 Block Diagram 48-MHz Reference Clock 24-MHz Clock (bus clk) Figure 17-2 is a block diagram of the USB module. USB CONTROLLER Serial Interface Engine (SIE) Enable USBDP Pullup IRQ SkyBlue Gasket USB RAM 256 bytes BVCI Target TX Logic XCVR USBDP USBDN Protocol and Rate Match VUSB33 RAM Arbitration Buffer Manager BVCI Initiator RX Logic To Interrupt Controller Peripheral Bus Local Bus VREG Figure 17-2. USB Module Block Diagram MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 299 Universal Serial Bus Device Controller (S08USBV1) 17.2 External Signal Description Table 17-3. USB External Pins Name Port USBDP USBDN Direction I/O I/O Function Differential USB signaling. Differential USB signaling. 3.3 V USB voltage regulator output or 3.3 V USB transceiver/resistor supply input. Reset State High impedance High impedance — The USB module requires both data and power pins. Table 17-3 describes each of the USB external pin Positive USB differential signal Negative USB differential signal USB voltage regulator power pin VUSB33 Power 17.2.1 USBDP USBDP is the positive USB differential signal. In a USB peripheral application, connect an external 33 Ω ±1% resistor in series with this signal in order to meet the USB Specification Rev. 2.0 impedance requirement. 17.2.2 USBDN USBDN is the negative USB differential signal. In a USB peripheral application, connect an external 33 Ω ±1% resistor in series with this signal in order to meet the USB Specification, Rev. 2.0 impedance requirement. 17.2.3 VUSB33 VUSB33 is connected to the on-chip 3.3-V voltage regulator (VREG). VUSB33 maintains an output voltage of 3.3 V and can only source enough current for USB internal transceiver (XCVR) and USB pullup resistor. If the VREG is disabled by software, the application must input an external 3.3 V power supply to the USB module via VUSB33. 17.3 Register Definition This section describes the memory map and control/status registers for the USB module. MC9S08JM60 Series Data Sheet, Rev. 3 300 Freescale Semiconductor Universal Serial Bus Device Controller (S08USBV1) 17.3.1 USB Control Register 0 (USBCTL0) 7 6 5 4 3 2 1 0 R 0 USBPU W USBRESET Reset 0 0 USBRES MEN 0 LPRESF 0 USBVREN 0 USBPHYEN 0 0 0 0 0 = Unimplemented or Reserved Figure 17-3. USB Transceiver and Regulator Control Register 0 (USBCTL0) Table 17-4. USBCTL0 Field Descriptions Field 7 USBRESET Description USB Reset — This bit generates a hard reset of the USB module, USBPHYEN and USBVREGEN bits will also be cleared. (need remember to restart USB Transceiver and USB voltage regulator). When set to 1, this bit automatically clears when the reset occurs. 0 USB module normal operation 1 Returns the USB module to its reset state Pull Up Source — This bit determines the source of the pullup resistor on the USBDP line. 0 Internal USBDP pullup resistor is disabled; The application can use an external pullup resistor 1 Internal USBDP pullup resistor is enabled USB Low-Power Resume Event Enable — This bit, when set, enables the USB module to send an asynchronous wakeup interrupt to the MCU upon detection that the LPRESF bit has been set, indicating a K-state on the USB bus. This bit must be set before entering low-power stop3 mode only after SLEEPF=1 (USB is entering suspend mode). It must be cleared immediately after stop3 recovery in order to clear the Low-Power Resume Flag. 0 USB asynchronous wakeup from suspend mode disabled 1 USB asynchronous wakeup from suspend mode enabled Low-Power Resume Flag — This bit becomes set in USB suspend mode if USBRESMEN=1 and a K-state is detected on the USB bus, indicating resume signaling while the device is in a low-power stop3 mode. This flag bit will trigger an asynchronous interrupt, which will wake the device from stop3. Firmware must then clear the USBRESMEN bit in order to clear the LPRESF bit. 0 No K-state detected on the USB bus while the device is in stop3 and the USB is suspended. 1 K-state detected on the USB bus when USBRESMEN=1, the device is in stop3, and the USB is suspended. USB Voltage Regulator Enable — This bit enables the on-chip 3.3V USB voltage regulator. 0 On-chip USB voltage regulator is disabled (OFF MODE) 1 On-chip USB voltage regulator is enabled for active or standby mode USB Transceiver Enable — When the USB Transceiver (XCVR) is disabled, USBDP and USBDN are hi-Z. It is recommended that the XCVR be enabled before setting the USBEN bit in the CTL register. The firmware must ensure that the XCVR remains enabled when entering USB SUSPEND mode. 0 On-chip XCVR is disabled 1 On-chip XCVR is enabled 6 USBPU 5 USBRESMEN 4 LPRESF 2 USBVREN 0 USBPHYEN 17.3.2 Peripheral ID Register (PERID) The PERID reads back the value of 0x04. This value is defined for the USB module peripheral. MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 301 Universal Serial Bus Device Controller (S08USBV1) 7 6 5 4 3 2 1 0 R W Reset 0 0 ID5 ID4 ID3 ID2 ID1 ID0 0 0 0 0 0 1 0 0 = Unimplemented or Reserved Figure 17-4. Peripheral ID Register (PERID) Table 17-5. PERID Field Descriptions Field 5:0 ID[5:0] Description Peripheral Configuration Number —This number is set to 0x04 and indicates that the peripheral is the full-speed USB module. 17.3.3 Peripheral ID Complement Register (IDCOMP) The IDCOMP reads back the complement of the peripheral ID register. For the USB module peripheral this will be 0xFB. 7 6 5 4 3 2 1 0 R W Reset 1 1 NID5 NID4 NID3 NID2 NID1 NID0 1 1 1 1 1 0 1 1 = Unimplemented or Reserved Figure 17-5. Peripheral ID Complement Register (IDCOMP) Table 17-6. IDCOMP Field Descriptions Field 5:0 NID[5:0] Description Compliment ID Number — One’s complement version of ID[5:0]. 17.3.4 Peripheral Revision Register (REV) The REV reads back the value of the USB peripheral revision. 7 6 5 4 3 2 1 0 R W Reset REV7 REV6 REV5 REV4 REV3 REV2 REV1 REV0 0 0 0 0 0 0 0 0 = Unimplemented or Reserved Figure 17-6. Peripheral Revision Register (REV) MC9S08JM60 Series Data Sheet, Rev. 3 302 Freescale Semiconductor Universal Serial Bus Device Controller (S08USBV1) Table 17-7. REV Field Descriptions Field 8–0 REV[7:0] Description Revision — Revision number of the USB module. 17.3.5 Interrupt Status Register (INTSTAT) The INTSTAT contains bits for each of the interrupt source within the USB module. Each of these bits is qualified with its respective interrupt enable bits (see the interrupt enable register). All bits of the register are logically OR'ed together to form a single interrupt source for the microcontroller. Once an interrupt bit has been set, it may only be cleared by writing a 1 to the respective interrupt bit. This register will contain the value of 0x00 after a reset. 7 6 5 4 3 2 1 0 R W Reset STALLF 0 0 RESUMEF 0 SLEEPF 0 TOKDNEF 0 SOFTOKF 0 ERRORF 0 USBRSTF 0 0 = Unimplemented or Reserved Figure 17-8. Interrupt Status Register (INTSTAT) Table 17-9. INTSTAT Field Descriptions Field 7 STALLF Description Stall Flag — The stall interrupt is used in device mode. In device mode the stall flag is asserted when a STALL handshake is sent by the serial interface engine (SIE). 0 A STALL handshake has not been sent 1 A STALL handshake has been sent Resume Flag — This bit is set 2.5 μs after clocks to the USB module have restarted following resume signaling. It can be used to indicate remote wakeup signaling on the USB bus. This interrupt is enabled only when the USB module is about to enter suspend mode (usually when SLEEPF interrupt detected). 0 No RESUME observed 1 RESUME detected (K-state is observed on the USBDP/USBDN signals for 2.5 μs) Sleep Flag — This bit is set if the USB module has detected a constant idle on the USB bus for 3 ms, indicating that the USB module will go into suspend mode. The sleep timer is reset by activity on the USB bus. 0 No constant idle state of 3 ms has been detected on the USB bus 1 A constant idle state of 3 ms has been detected on the USB bus Token Complete Flag — This bit is set when the current transaction is completed. The firmware must immediately read the STAT register to determine the endpoint and BD information. Clearing this bit (by setting it to 1) causes the STAT register to be cleared or the STAT FIFO holding register to be loaded into the STAT register. 0 No tokens being processed are complete 1 Current token being processed is complete SOF Token Flag — This bit is set if the USB module has received a start of frame (SOF) token. 0 The USB module has not received an SOF token 1 The USB module has received an SOF token 5 RESUMEF 4 SLEEPF 3 TOKDNEF 2 SOFTOKF MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 303 Universal Serial Bus Device Controller (S08USBV1) Table 17-9. INTSTAT Field Descriptions (continued) Field 1 ERRORF Description Error Flag — This bit is set when any of the error conditions within the ERRSTAT register has occurred. The firmware must then read the ERRSTAT register to determine the source of the error. 0 No error conditions within the ERRSTAT register have been detected 1 Error conditions within the ERRSTAT register have been detected USB Reset Flag —This bit is set when the USB module has decoded a valid USB reset. When asserted, this bit will inform the MCU to automatically write 0x00 to the address register and to enable endpoint 0. USBRSTF is set once a USB reset has been detected for 2.5 μs. It will not be asserted again until the USB reset condition has been removed, and then reasserted. 0 No USB reset observed 1 USB reset detected 0 USBRSTF 17.3.6 Interrupt Enable Register (INTENB) The INTENB contains enabling bits for each of the interrupt sources within the USB module. Setting any of these bits will enable the respective interrupt source in the INTSTAT register. This register will contain the value of 0x00 after a reset, i.e. all interrupts disabled. 7 6 5 4 3 2 1 0 R W Reset STALL 0 0 RESUME 0 SLEEP 0 TOKDNE 0 SOFTOK 0 ERROR 0 USBRST 0 0 Figure 17-9. Interrupt Enable Register (INTENB) Table 17-10. INTENB Field Descriptions Field 7 STALL 5 RESUME 4 SLEEP 3 TOKDNE 2 SOFTOK Description STALL Interrupt Enable — Setting this bit will enable STALL interrupts. 0 Interrupt disabled 1 Interrupt enabled RESUME Interrupt Enable — Setting this bit will enable RESUME interrupts. 0 Interrupt disabled 1 Interrupt enabled SLEEP Interrupt Enable — Setting this bit will enable SLEEP interrupts. 0 Interrupt disabled 1 Interrupt enabled TOKDNE Interrupt Enable — Setting this bit will enable TOKDNE interrupts. 0 Interrupt disabled 1 Interrupt enabled SOFTOK Interrupt Enable — Setting this bit will enable SOFTOK interrupts. 0 Interrupt disabled 1 Interrupt enabled MC9S08JM60 Series Data Sheet, Rev. 3 304 Freescale Semiconductor Universal Serial Bus Device Controller (S08USBV1) Table 17-10. INTENB Field Descriptions (continued) Field 1 ERROR 0 USBRST Description ERROR Interrupt Enable — Setting this bit will enable ERROR interrupts. 0 Interrupt disabled 1 Interrupt enabled USBRST Interrupt Enable — Setting this bit will enable USBRST interrupts. 0 Interrupt disabled 1 Interrupt enabled 17.3.7 Error Interrupt Status Register (ERRSTAT) The ERRSTAT contains bits for each of the error sources within the USB module. Each of these bits corresponds to its respective error enable bit (See Section 17.3.8, “Error Interrupt Enable Register (ERRENB)”.) The result is OR'ed together and sent to the ERROR bit of the INTSTAT register. Once an interrupt bit has been set, it may only be cleared by writing a 1 to the corresponding flag bit. Each bit is set as soon as the error condition is detected. Thus, the interrupt will typically not correspond with the end of a token being processed. This register will contain the value of 0x00 after reset. 7 6 5 4 3 2 1 0 R BTSERRF W Reset 0 0 Reserved BUFERRF 0 BTOERRF 0 DFN8F 0 CRC16F 0 CRC5F 0 PIDERRF 0 Figure 17-10. Error Interrupt Status Register (ERRSTAT) Table 17-11. ERRSTAT Field Descriptions Field 7 BTSERRF Description Bit Stuff Error Flag — A bit stuff error has been detected. If set, the corresponding packet will be rejected due to a bit stuff error. 0 No bit stuff error detected 1 Bit stuff error flag set Buffer Error Flag — This bit is set if the USB module has requested a memory access to read a new BD but has not been given the bus before the USB module needs to receive or transmit data. If processing a TX (IN endpoint) transfer, this would cause a transmit data underflow condition. Or if processing an Rx (OUT endpoint) transfer, this would cause a receive data overflow condition. This bit is also set if a data packet to or from the host is larger than the buffer size that is allocated in the BD. In this case the data packet is truncated as it is put into buffer memory. 0 No buffer error detected 1 A buffer error has occurred Bus Turnaround Error Timeout Flag — This bit is set if a bus turnaround timeout error has occurred. The USB module uses a bus turnaround timer to keep track of the amount of time elapsed between the token and data phases of a SETUP or OUT TOKEN or the data and handshake phases of an IN TOKEN. If more than 16-bit times are counted from the previous EOP before a transition from IDLE, a bus turnaround timeout error will occur. 0 No bus turnaround timeout error has been detected 1 A bus turnaround timeout error has occurred 5 BUFERRF 4 BTOERRF MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 305 Universal Serial Bus Device Controller (S08USBV1) Table 17-11. ERRSTAT Field Descriptions (continued) Field 3 DFN8F Description Data Field Error Flag — The data field received was not an interval of 8 bits. The USB Specification specifies that the data field must be an integer number of bytes. If the data field was not an integer number of bytes, this bit will be set. 0 The data field was an integer number of bytes 1 The data field was not an integer number of bytes CRC16 Error Flag — The CRC16 failed. If set, the data packet was rejected due to a CRC16 error. 0 No CRC16 error detected 1 CRC16 error detected CRC5 Error Flag — This bit will detect a CRC5 error in the token packets generated by the host. If set, the token packet was rejected due to a CRC5 error. 0 No CRC5 error detected 1 CRC5 error detected, and the token packet was rejected. PID Error Flag — The PID check failed. 0 No PID check error detected 1 PID check error detected 2 CRC16F 1 CRC5F 0 PIDERRF 17.3.8 Error Interrupt Enable Register (ERRENB) 7 6 5 4 3 2 1 0 R BTSERR W Reset 0 0 BUFERR 0 BTOERR 0 DFN8 0 CRC16 0 CRC5 0 PIDERR 0 0 Figure 17-11. Error Interrupt Enable Register (ERRENB) Table 17-12. ERRSTAT Field Descriptions Field 7 BTSERR 5 BUFERR 4 BTOERR 3 DFN8 2 CRC16 Description BTSERR Interrupt Enable — Setting this bit will enable BTSERR interrupts. 0 Interrupt disabled 1 Interrupt enabled BUFERR Interrupt Enable — Setting this bit will enable BUFERR interrupts. 0 Interrupt disabled 1 Interrupt enabled BTOERR Interrupt Enable — Setting this bit will enable BTOERR interrupts. 0 Interrupt disabled 1 Interrupt enabled DFN8 Interrupt Enable — Setting this bit will enable DFN8 interrupts. 0 Interrupt disabled 1 Interrupt enabled CRC16 Interrupt Enable — Setting this bit will enable CRC16 interrupts. 0 Interrupt disabled 1 Interrupt enabled MC9S08JM60 Series Data Sheet, Rev. 3 306 Freescale Semiconductor Universal Serial Bus Device Controller (S08USBV1) Table 17-12. ERRSTAT Field Descriptions (continued) Field 1 CRC5 0 PIDERR Description CRC5 Interrupt Enable — Setting this bit will enable CRC5 interrupts. 0 Interrupt disabled 1 Interrupt enabled PIDERR Interrupt Enable — Setting this bit will enable PIDERR interrupts. 0 Interrupt disabled 1 Interrupt enabled 17.3.9 Status Register (STAT) The STAT reports the transaction status within the USB module. When the MCU receives a TOKDNE interrupt, the STAT is read to determine the status of the previous endpoint communication. The data in the status register is valid only when the TOKDNEF interrupt flag is asserted. The STAT register is actually a read window into a status FIFO maintained by the USB module. When the USB module uses a BD, it updates the status register. If another USB transaction is performed before the TOKDNE interrupt is serviced, the USB module will store the status of the next transaction in the STAT FIFO. Thus, the STAT register is actually a four byte FIFO which allows the microcontroller to process one transaction while the serial interface engine (SIE) is processing the next. Clearing the TOKDNEF bit in the INTSTAT register causes the SIE to update the STAT register with the contents of the next STAT value. If the next data in the STAT FIFO holding register is valid, the SIE will immediately reassert the TOKDNE interrupt. 7 6 5 4 3 2 1 0 R W Reset 0 0 ENDP[3:0] IN ODD 0 0 0 0 0 0 0 0 = Unimplemented or Reserved Figure 17-12. Status Register (STAT) Table 17-13. STAT Field Descriptions Field 7–4 ENDP[3:0] Description Endpoint Number — These four bits encode the endpoint address that received or transmitted the previous token. This allows the microcontroller to determine which BDT entry was updated by the last USB transaction. 0000 Endpoint 0 0001 Endpoint 1 0010 Endpoint 2 0011 Endpoint 3 0100 Endpoint 4 0101 Endpoint 5 0110 Endpoint 6 MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 307 Universal Serial Bus Device Controller (S08USBV1) Table 17-13. STAT Field Descriptions (continued) Field 3 IN Description In/Out Transaction — This bit indicates whether the last BDT updated was for a transmit (IN) transfer or a receive (OUT) data transfer. 0 Last transaction was a receive (OUT) data transfer 1 Last BDT updated was for transmit (IN) transfer Odd/Even Transaction —This bit indicates whether the last buffer descriptor updated was in the odd bank of the BDT or the even bank of the BDT, See earlier section for more information on BDT address generation. 0 Last buffer descriptor updated was in the EVEN bank 1 Last buffer descriptor updated was in the ODD bank 2 ODD 17.3.10 Control Register (CTL) The CTL provides various control and configuration information for the USB module. 7 6 5 4 3 2 1 0 R TSUSPEND W Reset 0 0 0 0 0 0 0 0 CRESUME ODDRST USBEN Figure 17-13. Control Register (CTL) Table 17-14. CTL Field Descriptions Field 5 TSUSPEND Description Transaction Suspend — This bit is set by the serial interface engine (SIE) when a setup token is received, allowing software to dequeue any pending packet transactions in the BDT before resuming token processing. The TSUSPEND bit informs the processor that the SIE has disabled packet transmission and reception. Clearing this bit allows the SIE to continue token processing. 0 Allows the SIE to continue token processing 1 Set by the SIE when a setup token is received; SIE has disabled packet transmission and reception. Resume Signaling — Setting this bit will allow the USB module to execute resume signaling. This will allow the USB module to perform remote wakeup. Software must set CRESUME to 1 for the amount of time required by the USB Specification Rev. 2.0 and then clear it to 0. 0 Do not execute remote wakeup 1 Execute resume signaling - remote wakeup Odd Reset — Setting this bit will reset all the buffer descriptor ODD ping-pong bits to 0 which will then specify the EVEN descriptor bank. This bit is used with double-buffered endpoints 5 and 6. This bit has no effect on endpoints 0 through 4. 0 Do not reset 1 Reset all the buffer descriptor ODD ping/pong bits to 0 which will then specify the EVEN descriptor bank USB Enable Setting this bit will enable the USB module to operate. Setting this bit causes the SIE to reset all of its ODD bits to the BDTs. Thus, setting this bit will reset much of the logic in the SIE. 0 Disable the USB module 1 Enable the USB module for operation, will not affect Transceiver and VREG. 2 CRESUME 1 ODDRST 0 USBEN MC9S08JM60 Series Data Sheet, Rev. 3 308 Freescale Semiconductor Universal Serial Bus Device Controller (S08USBV1) 17.3.11 Address Register (ADDR) The ADDR register contains the unique 7-bit address the device will be recognized as through USB. The register is reset to 0x00 after the reset input has gone active or the USB module has decoded USB reset signaling. That will initialize the address register to decode address 0x00 as required by the USB specification. Firmware will change the value when it processes a SET_ADDRESS request. 7 6 5 4 3 2 1 0 R W Reset 0 ADDR6 0 0 ADDR5 0 ADDR4 0 ADDR3 0 ADDR2 0 ADDR1 0 ADDR0 0 Figure 17-14. Address Register (ADDR) Table 17-15. ADDR Field Descriptions Field 6–0 ADDR[6:0] Description USB Address — This 7-bit value defines the USB address that the USB module will decode 17.3.12 Frame Number Register (FRMNUML, FRMNUMH) The frame number registers contains the 11-bit frame number. The frame number registers require two 8-bit registers to implement. The low order byte is contained in FRMNUML, and the high order byte is contained in FRMNUMH. These registers are updated with the current frame number whenever a SOF TOKEN is received. 7 6 5 4 3 2 1 0 R W Reset FRM7 FRM6 FRM5 FRM4 FRM3 FRM2 FRM1 FRM0 0 0 0 0 0 0 0 0 = Unimplemented or Reserved Figure 17-15. Frame Number Register Low (FRMNUML) Table 17-16. FRMNUML Field Descriptions Field 7–0 FRM[7:0] Description Frame Number — These bits represent the low order bits of the 11 bit frame number. MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 309 Universal Serial Bus Device Controller (S08USBV1) 7 6 5 4 3 2 1 0 R W Reset 0 0 0 0 0 FRM10 FRM9 FRM8 0 0 0 0 0 0 0 0 = Unimplemented or Reserved Figure 17-16. Frame Number Register High (FRMNUMH) Table 17-17. FRMNUMH Field Descriptions Field 2–0 FRM[10:8] Description Frame Number — These bits represent the high order bits of the 11-bit frame number. 17.3.13 Endpoint Control Register (EPCTLn, n=0-6) The endpoint control registers contains the endpoint control bits (EPCTLDIS, EPRXEN, EPTXEN, and EPHSHK) for each endpoint available within the USB module for a decoded address. These four bits define all of the control necessary for any one endpoint. The formats for these registers are shown in the tables below. Endpoint 0 (ENDP0) is associated with control pipe 0 which is required by the USB for all functions. Therefore, after a USBRST interrupt has been received, the microcontroller must set EPCTL0 to contain 0x0D. 7 6 5 4 3 2 1 0 R W Reset (EP0-6) 0 0 0 EPCTLDIS EPRXEN EPTXEN EPSTALL EPHSHK 0 0 0 0 0 0 0 0 = Unimplemented or Reserved Figure 17-17. Endpoint Control Register (EPCTLn) Table 17-18. EPCTLn Field Descriptions Field 4 EPCTLDIS 3 EPRXEN 2 EPTXEN Description Endpoint Control — This bit defines if an endpoint is enabled and the direction of the endpoint. The endpoint enable/direction control is defined in Table 17-19. Endpoint Rx Enable — This bit defines if an endpoint is enabled for OUT transfers. The endpoint enable/direction control is defined in Table 17-19. Endpoint Tx Enable — This bit defines if an endpoint is enabled for IN transfers. The endpoint enable/direction control is defined in Table 17-19. MC9S08JM60 Series Data Sheet, Rev. 3 310 Freescale Semiconductor Universal Serial Bus Device Controller (S08USBV1) Table 17-18. EPCTLn Field Descriptions (continued) Field 1 EPSTALL Description Endpoint Stall — When set, this bit indicates that the endpoint is stalled. This bit has priority over all other control bits in the endpoint control register, but is only valid if EPTXEN=1 or EPRXEN=1. Any access to this endpoint will cause the USB module to return a STALL handshake. Once an endpoint is stalled it requires intervention from the host controller. 0 Endpoint n is not stalled 1 Endpoint n is stalled Endpoint Handshake — This bit determines if the endpoint will perform handshaking during a transaction to the endpoint. This bit will generally be set unless the endpoint is isochronous. 0 No handshaking performed during a transaction to this endpoint (usually for isochronous endpoints) 1 Handshaking performed during a transaction to this endpoint 0 EPHSHK Table 17-19. Endpoint Enable/Direction Control Bit Name 4 EPCTLDIS X X X 0 1 3 EPRXEN 0 0 1 1 1 2 EPTXEN 0 1 0 1 1 Disable endpoint Enable endpoint for IN(TX) transfers only Enable endpoint for OUT(RX) transfers only Enable endpoint for IN, OUT and SETUP transfers. RESERVED Endpoint Enable/Direction Control 17.4 Functional Description This section describes the functional behavior of the USB module. It documents data packet processing for endpoint 0 and data endpoints, USB suspend and resume states, SOF token processing, reset conditions and interrupts. 17.4.1 Block Descriptions Figure 17-2 is the block diagram. The module’s sub-blocks and external signals are described in the following sections. The module involves several major blocks — USB transceiver (XCVR), USB serial interface engine (SIE), a 3.3 V regulator (VREG), endpoint buffer manager, shared RAM arbitration, USB RAM and the SkyBlue gasket. 17.4.1.1 USB Serial Interface Engine (SIE) The SIE is composed of two major functions: TX Logic and RX Logic. These major functions are described below in more detail. The TX and RX logic are connected by a USB protocol engine which manages packet flow to and from the USB module. The SIE is connected to the rest of the system via MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 311 Universal Serial Bus Device Controller (S08USBV1) internal basic virtual component interface (BVCI) compliant target and initiator buses. The BVCI target interface is used to configure the USB SIE and to provide status and interrupts to CPU. The BVCI initiator interface provides the integrated DMA controller access to the buffer descriptor table (BDT), and transfers USB data to or from USB RAM memory. 17.4.1.1.1 Serial Interface Engine (SIE) Transmitter Logic The SIE transmitter logic has two primary functions. The first is to format the USB data packets that have been stored in the endpoint buffers. The second is to transmit data packets via the USB transceiver. All of the necessary USB data formatting is performed by the SIE transmitter logic, including: • NRZI encoding • bit-stuffing • CRC computation • addition of the SYNC field • addition of the End-of-packet (EOP) The CPU typically places data in the endpoint buffers as part of the application. When the buffer is configured as an IN buffer and the USB host requests a packet, the SIE responds with a properly formatted data packet. The transmitter logic is also used to generate responses to packets received from the USB host. When a properly formatted packet is received from the USB host, the transmitter logic responds with the appropriate ACK, NAK or STALL handshake. When the SIE transmitter logic is transmitting data from the buffer space for a particular endpoint, CPU access to that endpoint buffer space is not recommended. 17.4.1.1.2 Serial Interface Engine (SIE) Receiver Logic The SIE receiver logic receives USB data and stores USB packets in USB RAM for processing by the CPU and the application software. Serial data from the transceiver is converted to a byte-wide parallel data stream, checked for proper packet framing, and stored in the USB RAM memory. Received bitstream processing includes the following operations: • decodes an NRZI USB serial data stream • Sync detection • Bit-stuff removal (and error detection) • End-of-packet (EOP) detection • CRC validation • PID check • other USB protocol layer checks. The SIE receiver logic provides error detection including: • Bad CRC • Timeout detection for EOP MC9S08JM60 Series Data Sheet, Rev. 3 312 Freescale Semiconductor Universal Serial Bus Device Controller (S08USBV1) • Bit stuffing violation If a properly formatted packet is received, the receiver logic initiates a handshake response to the host. If the packet is not decoded correctly due to bit stuff violation, CRC error or other packet level problem, the receiver ignores it. The USB host will eventually time-out waiting for a response, and retransmit the packet. When the SIE receiver logic is receiving data in the buffer space for a particular endpoint, CPU access to that buffer space is not recommended. 17.4.1.2 17.4.1.2.1 MCU/Memory Interfaces SkyBlue Gasket The SkyBlue gasket connects the USB module to the SoC internal peripheral bus. The gasket maps accesses to the endpoint buffer descriptors or the endpoint buffers into the shared RAM block, and it also maps accesses to the peripherals register set into the serial interface engine (SIE) register space. The SkyBlue gasket interface includes registers to control the USB transceiver and voltage regulator. 17.4.1.2.2 Endpoint Buffer Manager Each endpoint supported by the USB device transmits data to and from buffers stored in the shared buffer memory. The serial interface engine (SIE) uses a table of descriptors, the Buffer Descriptor Table (BDT), which is also stored in the USB RAM to describe the characteristics of each endpoint. The endpoint buffer manager is responsible for mapping requests to access endpoint buffer descriptors into physical addresses within the USB RAM block. 17.4.1.2.3 RAM Arbitration The arbitration block allows access to the USB RAM block from the SkyBlue gasket block and from the SIE. 17.4.1.3 USB RAM The USB module includes 256 bytes of high speed RAM, accessible by the USB serial interface engine (SIE) and the CPU. The USB RAM runs at twice the speed of the bus clock to allow interleaved non-blocked access by the CPU and SIE. The USB RAM is used for storage of the buffer descriptor table (BDT) and endpoint buffers. USB RAM that is not allocated for the BDT and endpoint buffers can be used as system memory. If the USB module is not enabled, then the entire USB RAM may be used as unsecured system memory. 17.4.1.4 USB Transceiver (XCVR) The USB transceiver is electrically compliant to the Universal Serial Bus Specification 2.0. This block provides the necessary 2-wire differential NRZI signaling for USB communication. The transceiver is on-chip to provide a cost effective single chip USB peripheral solution. MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 313 Universal Serial Bus Device Controller (S08USBV1) 17.4.1.5 USB On-Chip Voltage Regulator (VREG) The on-chip 3.3-V regulator provides a stable power source to power the USB internal transceiver and provide for the termination of an internal or external pullup resistor. When the on-chip regulator is enabled, it requires a voltage supply input in the range from 3.9 V to 5.5 V, and the voltage regulator output will be in the range of 3.0 V to 3.6 V. With a dedicated on-chip USB 3.3-V regulator and a separate power supply for the MCU, the MCU and USB can operate at different voltages (See the USB electricals regarding the USB voltage regulator electrical characteristics). When the on-chip 3.3-V regulator is disabled, a 3.3-V source must be provided through the VUSB33 pin to power the USB transceiver. In this case, the power supply voltage to the MCU must not fall below the input voltage at the VUSB33 pin. The 3.3-V regulator has 3 modes including: • Active mode — This mode is entered when USB is active. Current requirement is sufficient to power the transceiver and the USBDP pullup resistor. • Standby — The voltage regulator standby mode is entered automatically when the USB device is in suspend mode. When the USB device is forced into suspend mode by the USB bus, the firmware must configure the MCU for stop3 mode. In standby mode, the requirement is to maintain the USBDP pin voltage at 3.0 V to 3.6 V, with a 900 Ω (worst-case) pullup. • Power off — This mode is entered anytime when stop2 or stop1 is entered or when the voltage regulator is disabled. 17.4.1.6 USB On-Chip USBDP Pullup Resistor The pullup resistor on the USBDP line required for full-speed operation by the USB Specification Rev. 2.0 can be internal or external to the MCU, depending on the application requirements. An on-chip pullup resistor, implemented as specified in the USB 2.0 resistor ECN, is optionally available via firmware configuration. Alternatively, this on-chip pullup resistor can be disabled, and the USB module can be configured to use an external pullup resistor for the USBDP line instead. If using an external pullup resistor on the USBDP line, the resistor must comply with the requirements in the USB 2.0 resistor ECN found at http://www.usb.org. The USBPU bit in the USBCTL0 register can be used to indicate if the pullup resistor is internal or external to the MCU. If USBPU is clear, the internal pullup resistor on USBDP is disabled, and an external USBDP pullup can be used. When using an external USBDP pullup, if the voltage regulator is enabled, the VUSB33 voltage output can be used with the USBDP pullup. While the use of the internal USBDP pullup resistor is generally recommended, the figure below shows the USBDP pullup resistor configuration for a USB device using an external resistor tied to VUSB33. MC9S08JM60 Series Data Sheet, Rev. 3 314 Freescale Semiconductor Universal Serial Bus Device Controller (S08USBV1) USB DEVICE 3.3 V VUSB33 RDPPU USBDP USBDN Figure 17-18. USBDP/USBDN Pullup Resistor Configuration for USB module 17.4.1.7 USB Powering and USBDP Pullup Enable Options The USB module provides a single-chip solution for USB device applications that are self-powered or bus-powered. The USB device needs to know when it has a valid USB connection in order to enable or disable the pullup resistor on the USBDP line. For the USB module on this device, the pullup on USBDP is only applied when a valid VBUS connection is sensed, as required by the USB specification. In bus-powered applications, system power must be derived from VBUS. Because VBUS is only available when a valid USB connection from host to device is made, the VBUS sensing is built-in, and the USBDP pullup can be enabled accordingly. With self-powered applications, determining when a valid USB connection is made is different from that of bus-powered applications. In self-powered applications, VBUS sensing must be built into the application. For instance, a KBI pin interrupt can be utilized (if available). When a valid VBUS connection is made, the KBI interrupt can notify the application that a valid USB connection is available, and the internal pullup resistor can be enabled using the USBPU bit. If an external pullup resistor is used instead of the internal one, the VBUS sensing mechanism must be included in the system design. Table 17-20 summarizes the differences in enabling the USBDP pullup for different USB power modes. Table 17-20. USBDP Pullup Enable for Different USB Power Modes Power Bus Power (Built-in VBUS sense) Self Power (Build VBUS sense into application) USBDP Pullup Internal External Internal External Pullup Enable Set USBPU bit Build into application Set USBPU bit Build into application MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 315 Universal Serial Bus Device Controller (S08USBV1) 17.4.2 Buffer Descriptor Table (BDT) To efficiently manage USB endpoint communications, the USB module implements a buffer descriptor table (BDT) comprised of buffer descriptors (BD) in the local USB RAM. The BD entries provide status or control information for a corresponding endpoint. The BD entries also provide an address to the endpoint’s buffer. A single BD for an endpoint direction requires 3-bytes. A detailed description of the BDT format is provided in the next sections. The software API intelligently manages buffers for the USB module by updating the BDT when needed. This allows the USB module to efficiently handle data transmission and reception, while the microcontroller performs communication overhead processing and other function dependent applications. Because the buffers are shared between the microcontroller and the USB module, a simple semaphore mechanism is used to distinguish who is allowed to update the BDT and buffers in buffer memory. A semaphore bit, the OWN bit, is cleared to 0 when the BD entry is owned by the microcontroller. The microcontroller is allowed read and write access to the BD entry and the data buffer when the OWN bit is 0. When the OWN bit is set to 1, the BD entry and the data buffer are owned by the USB module. The USB module now has full read and write access and the microcontroller must not modify the BD or its corresponding data buffer. 17.4.2.1 Multiple Buffer Descriptor Table Entries for a Single Endpoint Every endpoint direction requires at least one three-byte Buffer Descriptor entry. Thus, endpoint 0, a bidirectional control endpoint, requires one BDT entry for the IN direction, and one for the OUT direction. Using two BD entries also allows for double-buffering. Double-buffering BDs allows the USB module to easily transfer data at the maximum throughput provided by the USB module. Double buffering allows the MCU to process one BD while the USB module is processing the other BD. To facilitate double-buffering, two buffer descriptor (BD) entries are needed for each endpoint direction. One BD entry is the EVEN BD and the other is the ODD BD. 17.4.2.2 Addressing Buffer Descriptor Table Entries The BDT addressing is hardwired into the module. The BDT occupies the first portion of the USB RAM. To access endpoint data via the USB or MCU, the addressing mechanism of the buffer descriptor table must be understood. All enabled IN and OUT endpoint BD entries are indexed into the BDT to allow easy access via the USB module or the MCU. The figure below shows the USB RAM organization. The figure shows that the first entries in the USB RAM are dedicated to storage of the BDT entries - i.e. the first 30 bytes of the USB RAM (0x00 to 0x1D) are used to implement the BDT. MC9S08JM60 Series Data Sheet, Rev. 3 316 Freescale Semiconductor Universal Serial Bus Device Controller (S08USBV1) Table 17-21. USB RAM Organization USB RAM Offset 0x00 USB RAM Description of Contents Endpoint 0 IN Endpoint 0, OUT Endpoint 1 Endpoint 2 BDT Endpoint 3 Endpoint 4 Endpoint 5, Buffer EVEN Endpoint 5, Buffer ODD Endpoint 6, Buffer EVEN 0x1D 0x1E 0x1F 0x20 Endpoint 6, Buffer ODD RESERVED RESERVED USB RAM available for endpoint buffers 0xFF When the USB module receives a USB token on an enabled endpoint, it interrogates the BDT. The USB module reads the corresponding endpoint BD entry and determines if it owns the BD and corresponding data buffer. 17.4.2.3 Buffer Descriptor Formats The buffer descriptors (BDs) are groups of registers that provide endpoint buffer control information for the USB module and the MCU. The BDs have different meanings based on who is reading the BD in memory. The USB module uses the data stored in the BDs to determine: • Who owns the buffer in system memory • Data0 or Data1 PID • Release Own upon packet completion • Data toggle synchronization enable • How much data to be transmitted or received • Where the buffer resides in the buffer RAM. The microcontroller uses the data stored in the BDs to determine: • • • Who owns the buffer in system memory Data0 or Data1 PID The received TOKEN PID MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 317 Universal Serial Bus Device Controller (S08USBV1) • • How much data was transmitted or received. Where the buffer resides in buffer memory The BDT is composed of buffer descriptors (BD) which are used to define and control the actual buffers in the USB RAM space. BDs always occur as a 3-bytes block. See Figure 17-19 for the BD example of Endpoint 0 IN start from USB RAM offset 0x00. The format for the buffer descriptor is shown in Table 17-22. Offset R 0x00 W R 0x01 W R 0x02 W EPADR[9:4] BC[7:0] OWN DATA0/1 0 0 DTS BDTSTALL 7 6 5 4 3 2 1 0 BDTKPID[3] BDTKPID[3] BDTKPID[1] BDTKPID[0] 0 0 Figure 17-19. Buffer Descriptor Example Table 17-22. Buffer Descriptor Table Fields Field Description OWN — This OWN bit determines who currently owns the buffer. The USB SIE generally writes a 0 to this bit when it has completed a token. The USB module ignores all other fields in the BD when OWN=0. Once the BD has been assigned to the USB module (OWN=1), the MCU must not change it in any way. This byte of the BD must always be the last byte the MCU (firmware) updates when it initializes a BD. Although the hardware will not block the MCU from accessing the BD while owned by the USB SIE, doing so may cause undefined behavior and is generally not recommended. 0 The MCU has exclusive access to the entire BD 1 The USB module has exclusive access to the BD Data Toggle — This bit defines if a DATA0 field (DATA0/1=0) or a DATA1 (DATA0/1=1) field was transmitted or received. It is unchanged by the USB module. 0 Data 0 packet 1 Data 1 packet OWN DATA0/1 The current token PID is written back to the BD by the USB module when a transfer completes. The values BDTKPID[3:0] written back are the token PID values from the USB specification: 0x1 for an OUT token, 0x9 for and IN token or 0xd for a SETUP token. DTS Data Toggle Synchronization— This bit enables data toggle synchronization. 0 No data toggle synchronization is performed. 1 Data toggle synchronization is performed. BDT Stall — Setting this bit will cause the USB module to issue a STALL handshake if a token is received by the SIE that would use the BDT in this location. The BDT is not consumed by the SIE (the OWN bit remains and the rest of the BD is unchanged) when the BDTSTALL bit is set. 0 BDT stall is disabled 1 USB will issue a STALL handshake if a token is received by the SIE that would use the BDT in this location BDTSTALL MC9S08JM60 Series Data Sheet, Rev. 3 318 Freescale Semiconductor Universal Serial Bus Device Controller (S08USBV1) Table 17-22. Buffer Descriptor Table Fields (continued) Field Description Byte Count — The Byte Count bits represent the 8-bit byte count. The USB module serial interface engine (SIE) will change this field upon the completion of a RX transfer with the byte count of the data received. Note that while USB supports packets as large as 1023 bytes for isochronous endpoints, this module limits packet size to 64 bytes. Endpoint Address— The endpoint address bits represent the upper 6 bits of the 10-bit buffer address within the module’s local USB RAM. Bits [3:0] of EPADR are always zero, therefore the address of the buffer must always start on a 16-byte aligned address within the local RAM. These bits are unchanged by the USB module. This is NOT the address of the memory on the system bus. EPADR is relative to the start of the local USB RAM. BC[7:0] EPADR[9:4] 17.4.3 USB Transactions When the USB module transmits or receives data, it will first compute the BDT address based on the endpoint number, data direction, and which buffer is being used (even or odd), then it will read the BD. Once the BD has been read, and if the OWN bit equals 1, the serial interface engine (SIE) will transfer the packet data to or receive the packet data from the buffer pointed to by the EPADR field of the BD. When the USB TOKEN is complete, the USB module will update the BDT and change the OWN bit to 0. The STAT register is updated and the TOKDNE interrupt is set. When the microcontroller processes the TOKDNE interrupt, it reads the status register. This gives the microcontroller all the information it needs to process the endpoint. At this point the microcontroller can allocate a new BD, so additional USB data can be transmitted or received for that endpoint, and it can process the previous BD. Figure 17-20 shows a timeline for how a typical USB token would be processed. MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 319 Universal Serial Bus Device Controller (S08USBV1) = USB Host = Function USB RST SOF USBRST Interrupt Generated SOF Interrupt Generated SETUP TOKEN DATA ACK TOKDNE Interrupt Generated IN TOKEN DATA ACK TOKDNE Interrupt Generated OUT TOKEN DATA ACK TOKDNE Interrupt Generated Figure 17-20. USB Packet Flow The USB has two sources of data overrun error: • The memory latency to the local USB RAM interface may be too high and cause the receive buffer to overflow. This is predominantly a hardware performance issue, usually caused by transient memory access issues. • The packet received may be larger than the negotiated MAXPACKET size. This is caused by a software bug. In the first case, the USB will respond with a NAK or bus timeout (BTO) as appropriate for the class of transaction. The BTOERR bit will be set in the ERRSTAT register. Depending on the values of the INTENB and ERRENB register, USB module may assert an interrupt to notify the CPU of the error. In device mode the BDT is not written back nor is the TOKDNE interrupt triggered because it is assumed that a second attempt will be queued at future time and will succeed. In the second case of oversized data packets, the USB specification assumes correct software drivers on both sides. The overrun is not due to memory latency but to a lack of space to put the excess data. NAK'ing the packet will likely cause another retransmission of the already oversized packet data. In response to oversized packets, the USB module will still ACK the packet for non-isochronous transfers. The data written to memory is clipped to the MAXPACKET size so as not to corrupt the buffer space. The USB module will assert the BUFERRF bit of the ERRSTAT register (which could trigger an interrupt, as above) and a TOKDNE interrupt fails. The BDTKPID field of the BDT will not be “1111” because the BUFERRF is not due to latency. The packet length field written back to the BDT will be the MAXPACKET value to represent the length of the clipped data actually written to memory. From here the software can decide an MC9S08JM60 Series Data Sheet, Rev. 3 320 Freescale Semiconductor Universal Serial Bus Device Controller (S08USBV1) appropriate course of action for future transactions — stalling the endpoint, canceling the transfer, disabling the endpoint, etc. 17.4.4 USB Packet Processing Packet processing for a USB device consists of managing buffers for IN (to the USB Host) and OUT (to the USB device) transactions. Packet processing is further divided into request processing on Endpoint 0, and data packet processing on the data endpoints. 17.4.4.1 USB Data Pipe Processing Data pipe processing is essentially a buffer management task. The firmware is responsible for managing the shared buffer RAM to ensure that a BD is always ready for the hardware to process (OWN bit = 1). The device allocates buffers within the shared RAM, sets up the buffer descriptors, and waits for interrupts. On receipt of a TOKDNE interrupt, the firmware reads the STAT register to determine which endpoint is affected, then reads the corresponding BDT entry to determine what to do next. When processing data packets, firmware is responsible for managing the size of the packet buffers to be in compliance with the USB specification, and the physical limitations of this module. Packet sizes up to 64 bytes are supported on all endpoints. Isochronous endpoints also can only specify packet sizes up to 64 bytes. Firmware is also responsible for setting the appropriate bits in the BDT. For most applications using bulk packets (control, bulk, and interrupt-type transfers), the firmware will set the DTS, BC and EPADR fields for each BD. For isochronous packets, firmware will set BC and EPADR fields. In all cases, firmware will set the OWN bit to enable the endpoint for data transfers. 17.4.4.2 Request Processing on Endpoint 0 In most cases, commands to the USB device are directed to Endpoint 0. The host uses the “Standard Requests” described in Chapter 9 of the USB specification to enumerate and configure the device. Class drivers or product specific drivers running on the host send class (HID, Mass Storage, Imaging) and vendor specific commands to the device on endpoint 0. USB requests always follow a specific format: • Host sends a SETUP token, followed by an 8-byte setup packet, and the device hardware can send a handshake packet. • If the setup packet specifies a data phase, the host and device may transfer up to 64 Kbytes of data (either IN or OUT, not both). • The request is terminated by a status phase. Device firmware monitors the INTSTAT and STAT registers, the endpoint 0 buffer descriptors (BD’s), and the contents of the setup packet to correctly execute the host’s request. The flow for processing endpoint 0 requests is as follows: 1. Allocate 8-byte buffers for endpoint 0 OUT. MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 321 Universal Serial Bus Device Controller (S08USBV1) 2. Create BDT entries for Endpoint 0 OUT, and set the DTS and OWN bits to 1. 3. Wait for interrupt TOKDNE. 4. Read STAT register. — The status register must show Endpoint 0, RX. If it does not, then assert the EPSTALL bit in the endpoint control register. 5. Read Endpoint 0 OUT BD. — Verify that the token type is a SETUP token. If it is not, then assert the EPSTALL bit in the endpoint control register. 6. Decode and process the setup packet. — If the direction field in the setup packet indicates an OUT transfer, then process the out data phase to receive exactly the number of bytes specified in the wLength field of the setup packet. — If the direction field in the setup packet indicates an IN transfer, then process the in data phase to deliver no more than the number of bytes specified in the wLength field. Note that it is common for the host to request more bytes than it needs, expecting the device to only send as much as it needs to. 7. After processing the data phase (if there was one), create a zero-byte status phase transaction. — This is accomplished for an OUT data phase (IN status phase) by setting the BC to 0 in the next BD, while also setting OWN=1. For an IN data phase (OUT status phase), the host will send a zero-byte packet to the device. — Firmware can verify completion of the data phase by verifying the received token in the BD on receipt of the TOKDNE interrupt. If the data phase was of type IN, then the status phase token will be OUT. If the data phase was of type OUT, then the status phase token will be IN. 17.4.4.3 Endpoint 0 Exception Conditions The USB includes a number of error checking and recovery mechanisms to ensure reliable data transfer. One such exception occurs when the host sends a SETUP packet to a device, and the host never receives the acknowledge handshake from the device. In this case, the host will retry the SETUP packet. Endpoint 0 request handlers on the device must be aware of the possibility that after receiving a correct SETUP packet, they could receive another SETUP packet before the data phase actually begins. 17.4.5 Start of Frame Processing The USB host allocates time in 1.0 ms chunks called “Frames” for the purposes of packet scheduling. The USB host starts each frame with a broadcast token called SOF (start of frame) that includes an 11-bit sequence number. The TOKSOF interrupt is used to notify firmware when an SOF token was received. Firmware can read the current frame number from the FRMNUML/FRMNUMH registers. In general, the SOF interrupt is only monitored by devices using isochronous endpoints to help ensure that the device and host remain synchronized. MC9S08JM60 Series Data Sheet, Rev. 3 322 Freescale Semiconductor Universal Serial Bus Device Controller (S08USBV1) 17.4.6 Suspend/Resume The USB supports a single low-power mode called suspend. Getting into and out of the suspend state is described in the following sections. 17.4.6.1 Suspend The USB host can put a single device or the entire bus into the suspend state at any time. The MCU supports suspend mode for low power. Suspend mode will be entered when the USB data lines are in the idle state for more than 3 ms. Entry into suspend mode is announced by the SLEEPF bit in the INTSTAT register. Per the USB specification, a low-power bus-powered USB device is required to draw less than 500 µA in suspend state. A high-power device that supports remote wakeup and has its remote wake-up feature enabled by the host can draw up to 2.5 mA of current. After the initial 3-ms idle, the USB device will reach this state within 7 ms. This low-current requirement means that firmware is responsible for entering stop3 mode once the SLEEPF flag has been set and before the USB module has been placed in the suspend state. On receipt of resume signaling from the USB, the module can generate an asynchronous interrupt to the MCU which brings the device out of stop mode and wakes up the clocks. Setting the USBRESMEN bit in the USBCTL0 register immediately after the SLEEPF bit is set enables this asynchronous notification feature. The USB resume signaling will then cause the LPRESF bit to be set, indicating a low-power SUSPEND resume, which will wake the CPU from stop3 mode. During normal operation, while the host is sending SOF packets, the USB module will not enter suspend mode. 17.4.6.2 Resume There are three ways to get out of the suspend state. When the USB module is in suspend state, the resume detection is active even if all the clocks are disabled and the MCU is in stop3 mode. The MCU can be activated from the suspend state by normal bus activity, a USB reset signal, or upstream resume (remote wakeup). 17.4.6.2.1 Host Initiated Resume The host signals a resume from suspend by initiating resume signaling (K state) for at least 20 ms followed by a standard low-speed EOP signal. This 20 ms ensures that all devices in the USB network are awakened. After resuming the bus, the host must begin sending bus traffic within 3 ms to prevent the device from re-entering suspend mode. Depending on the power mode the device is in while suspended, the notification for a host initiated resume will be different: • Run mode - RESUME must be set after SLEEPF becomes set to enable the RESUMEF interrupt. Then, upon resume signaling, the RESUMEF interrupt will trigger after a K-state has been observed on the USBDP/USBDN lines for 2.5 µs. • Stop3 mode - USBRESMEN must be set after SLEEPF becomes set to arm the LPRESF bit. Then, upon a K-state on the bus while the device is in stop3 mode, the LPRESF bit will be set, indicating MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 323 Universal Serial Bus Device Controller (S08USBV1) a resume from low-power suspend. This will trigger an asynchronous interrupt to wake the CPU from stop3 mode and resume clocks to the USB module. NOTE As a precaution, after LPRESF is set, firmware must check the state of the USB bus to see if the K-state was a result of a transient event and not a true host-initiated resume. If this is the case, then the device can drop back into stop3 if necessary. To do this, the RESUME interrupt can be enabled in conjunction with the USBRESMEN feature. Then, after LPRESF is set, and a K-state is still detected approximately 2.5 µs after clocks have restarted, firmware can check that the RESUMEF interrupt has triggered, indicating resume signaling from the host. 17.4.6.2.2 USB Reset Signaling Reset can wake a device from the suspend state. 17.4.6.2.3 Remote Wakeup The USB device can send a resume event to the host by writing to the CRESUME bit. Firmware must first set the bit for the time period required by the USB Specification Rev. 2.0 (Section 7.1.7.7) and then clear it to 0. 17.4.7 Resets The module supports multiple types of resets. The first is a bus reset generated by the USB Host, the second is a module reset generated by the MCU. 17.4.7.1 USB Bus Reset At any time, the USB host may issue a reset to one or all of the devices attached to the bus. A USB reset is defined as a period of single ended zero (SE0) on the cable for greater than 2.5 μs. When the device detects reset signaling, it resets itself to the unconfigured state, and sets its USB address zero. The USB host uses reset signaling to force one or all connected devices into a known state prior to commencing enumeration. The USB module responds to reset signaling by asserting the USBRST interrupt in the INTSTAT register. Software is required to service this interrupt to ensure correct operation of the USB. 17.4.7.2 USB Module Reset USB module resets are initiated on-chip. During a module reset, the USB module is configured in the default mode. The USB module can also be forced into its reset state by setting the USBRESET bit in the USBCTL0 register. The default mode includes the following settings: • Interrupts masked. • USB clock enabled • USB voltage regulator disabled MC9S08JM60 Series Data Sheet, Rev. 3 324 Freescale Semiconductor Universal Serial Bus Device Controller (S08USBV1) • • • • USB transceiver disabled USBDP pullup disabled Endpoints disabled USB address register set to zero 17.4.8 Interrupts Interrupts from the INTSTAT register signify events which occur during normal operation — USB start of frame tokens (TOKSOF), packet completion (TOKDNE), USB bus reset (USBRST), endpoint errors (ERROR), suspend and resume (SLEEP and RESUME), and endpoint stalled (STALL). The ERRSTAT interrupts carry information about specific types of errors, which is needed on an application specific basis. Using ERRSTAT, an application can determine exactly why a packet transfer failed — due to CRC error, PID check error and so on. Both registers are maskable via the INTENB and ERRENB registers. The INTSTAT and ERRSTAT are used to signal interrupts in a two-level structure. Unmasked interrupts from the ERRSTAT register are reported in the INTSTAT register. Note that the interrupt registers work in concert with the STAT register. On receipt of an INTSTAT interrupt, software can check the STAT register and determine which BDT entry was affected by the transaction. MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 325 Universal Serial Bus Device Controller (S08USBV1) MC9S08JM60 Series Data Sheet, Rev. 3 326 Freescale Semiconductor Chapter 18 Development Support 18.1 Introduction Development support systems in the HCS08 include the background debug controller (BDC) and the on-chip debug module (DBG). The BDC provides a single-wire debug interface to the target MCU that provides a convenient interface for programming the on-chip flash and other nonvolatile memories. The BDC is also the primary debug interface for development and allows non-intrusive access to memory data and traditional debug features such as CPU register modify, breakpoints, and single instruction trace commands. In the HCS08 family, address and data bus signals are not available on external pins (not even in test modes). Debug is done through commands fed into the target MCU via the single-wire background debug interface. The debug module provides a means to selectively trigger and capture bus information so an external development system can reconstruct what happened inside the MCU on a cycle-by-cycle basis without having external access to the address and data signals. The alternate BDC clock source for MC9S08JM60 Series is the MCGLCLK. See Chapter 12, “Multi-Purpose Clock Generator (S08MCGV1),” for more information about MCGLCLK and how to select clock sources. MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 327 Development Support 18.1.1 Features Features of the BDC module include: • Single pin for mode selection and background communications • BDC registers are not located in the memory map • SYNC command to determine target communications rate • Non-intrusive commands for memory access • Active background mode commands for CPU register access • GO and TRACE1 commands • BACKGROUND command can wake CPU from stop or wait modes • One hardware address breakpoint built into BDC • Oscillator runs in stop mode, if BDC enabled • COP watchdog disabled while in active background mode Features of the ICE system include: • Two trigger comparators: Two address + read/write (R/W) or one full address + data + R/W • Flexible 8-word by 16-bit FIFO (first-in, first-out) buffer for capture information: — Change-of-flow addresses or — Event-only data • Two types of breakpoints: — Tag breakpoints for instruction opcodes — Force breakpoints for any address access • Nine trigger modes: — Basic: A-only, A OR B — Sequence: A then B — Full: A AND B data, A AND NOT B data — Event (store data): Event-only B, A then event-only B — Range: Inside range (A ≤ address ≤ B), outside range (address < A or address > B) 18.2 Background Debug Controller (BDC) All MCUs in the HCS08 family contain a single-wire background debug interface that supports in-circuit programming of on-chip nonvolatile memory and sophisticated non-intrusive debug capabilities. Unlike debug interfaces on earlier 8-bit MCUs, this system does not interfere with normal application resources. It does not use any user memory or locations in the memory map and does not share any on-chip peripherals. BDC commands are divided into two groups: • Active background mode commands require that the target MCU is in active background mode (the user program is not running). Active background mode commands allow the CPU registers to be read or written, and allow the user to trace one user instruction at a time, or GO to the user program from active background mode. MC9S08JM60 Series Data Sheet, Rev. 3 328 Freescale Semiconductor Development Support • Non-intrusive commands can be executed at any time even while the user’s program is running. Non-intrusive commands allow a user to read or write MCU memory locations or access status and control registers within the background debug controller. Typically, a relatively simple interface pod is used to translate commands from a host computer into commands for the custom serial interface to the single-wire background debug system. Depending on the development tool vendor, this interface pod may use a standard RS-232 serial port, a parallel printer port, or some other type of communications such as a universal serial bus (USB) to communicate between the host PC and the pod. The pod typically connects to the target system with ground, the BKGD pin, RESET, and sometimes VDD. An open-drain connection to reset allows the host to force a target system reset, which is useful to regain control of a lost target system or to control startup of a target system before the on-chip nonvolatile memory has been programmed. Sometimes VDD can be used to allow the pod to use power from the target system to avoid the need for a separate power supply. However, if the pod is powered separately, it can be connected to a running target system without forcing a target system reset or otherwise disturbing the running application program. BKGD 1 NO CONNECT 3 NO CONNECT 5 2 GND 4 RESET 6 VDD Figure 18-1. BDM Tool Connector 18.2.1 BKGD Pin Description BKGD is the single-wire background debug interface pin. The primary function of this pin is for bidirectional serial communication of active background mode commands and data. During reset, this pin is used to select between starting in active background mode or starting the user’s application program. This pin is also used to request a timed sync response pulse to allow a host development tool to determine the correct clock frequency for background debug serial communications. BDC serial communications use a custom serial protocol first introduced on the M68HC12 Family of microcontrollers. This protocol assumes the host knows the communication clock rate that is determined by the target BDC clock rate. All communication is initiated and controlled by the host that drives a high-to-low edge to signal the beginning of each bit time. Commands and data are sent most significant bit first (MSB first). For a detailed description of the communications protocol, refer to Section 18.2.2, “Communication Details.” If a host is attempting to communicate with a target MCU that has an unknown BDC clock rate, a SYNC command may be sent to the target MCU to request a timed sync response signal from which the host can determine the correct communication speed. BKGD is a pseudo-open-drain pin and there is an on-chip pullup so no external pullup resistor is required. Unlike typical open-drain pins, the external RC time constant on this pin, which is influenced by external capacitance, plays almost no role in signal rise time. The custom protocol provides for brief, actively driven speedup pulses to force rapid rise times on this pin without risking harmful drive level conflicts. Refer to Section 18.2.2, “Communication Details,” for more detail. MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 329 Development Support When no debugger pod is connected to the 6-pin BDM interface connector, the internal pullup on BKGD chooses normal operating mode. When a debug pod is connected to BKGD it is possible to force the MCU into active background mode after reset. The specific conditions for forcing active background depend upon the HCS08 derivative (refer to the introduction to this Development Support section). It is not necessary to reset the target MCU to communicate with it through the background debug interface. 18.2.2 Communication Details The BDC serial interface requires the external controller to generate a falling edge on the BKGD pin to indicate the start of each bit time. The external controller provides this falling edge whether data is transmitted or received. BKGD is a pseudo-open-drain pin that can be driven either by an external controller or by the MCU. Data is transferred MSB first at 16 BDC clock cycles per bit (nominal speed). The interface times out if 512 BDC clock cycles occur between falling edges from the host. Any BDC command that was in progress when this timeout occurs is aborted without affecting the memory or operating mode of the target MCU system. The custom serial protocol requires the debug pod to know the target BDC communication clock speed. The clock switch (CLKSW) control bit in the BDC status and control register allows the user to select the BDC clock source. The BDC clock source can either be the bus or the alternate BDC clock source. The BKGD pin can receive a high or low level or transmit a high or low level. The following diagrams show timing for each of these cases. Interface timing is synchronous to clocks in the target BDC, but asynchronous to the external host. The internal BDC clock signal is shown for reference in counting cycles. MC9S08JM60 Series Data Sheet, Rev. 3 330 Freescale Semiconductor Development Support Figure 18-2 shows an external host transmitting a logic 1 or 0 to the BKGD pin of a target HCS08 MCU. The host is asynchronous to the target so there is a 0-to-1 cycle delay from the host-generated falling edge to where the target perceives the beginning of the bit time. Ten target BDC clock cycles later, the target senses the bit level on the BKGD pin. Typically, the host actively drives the pseudo-open-drain BKGD pin during host-to-target transmissions to speed up rising edges. Because the target does not drive the BKGD pin during the host-to-target transmission period, there is no need to treat the line as an open-drain signal during this period. BDC CLOCK (TARGET MCU) HOST TRANSMIT 1 HOST TRANSMIT 0 10 CYCLES SYNCHRONIZATION UNCERTAINTY PERCEIVED START OF BIT TIME TARGET SENSES BIT LEVEL EARLIEST START OF NEXT BIT Figure 18-2. BDC Host-to-Target Serial Bit Timing MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 331 Development Support Figure 18-3 shows the host receiving a logic 1 from the target HCS08 MCU. Because the host is asynchronous to the target MCU, there is a 0-to-1 cycle delay from the host-generated falling edge on BKGD to the perceived start of the bit time in the target MCU. The host holds the BKGD pin low long enough for the target to recognize it (at least two target BDC cycles). The host must release the low drive before the target MCU drives a brief active-high speedup pulse seven cycles after the perceived start of the bit time. The host should sample the bit level about 10 cycles after it started the bit time. BDC CLOCK (TARGET MCU) HOST DRIVE TO BKGD PIN HIGH-IMPEDANCE TARGET MCU SPEEDUP PULSE HIGH-IMPEDANCE HIGH-IMPEDANCE PERCEIVED START OF BIT TIME R-C RISE BKGD PIN 10 CYCLES 10 CYCLES HOST SAMPLES BKGD PIN EARLIEST START OF NEXT BIT Figure 18-3. BDC Target-to-Host Serial Bit Timing (Logic 1) MC9S08JM60 Series Data Sheet, Rev. 3 332 Freescale Semiconductor Development Support Figure 18-4 shows the host receiving a logic 0 from the target HCS08 MCU. Because the host is asynchronous to the target MCU, there is a 0-to-1 cycle delay from the host-generated falling edge on BKGD to the start of the bit time as perceived by the target MCU. The host initiates the bit time but the target HCS08 finishes it. Because the target wants the host to receive a logic 0, it drives the BKGD pin low for 13 BDC clock cycles, then briefly drives it high to speed up the rising edge. The host samples the bit level about 10 cycles after starting the bit time. BDC CLOCK (TARGET MCU) HOST DRIVE TO BKGD PIN HIGH-IMPEDANCE TARGET MCU DRIVE AND SPEED-UP PULSE PERCEIVED START OF BIT TIME SPEEDUP PULSE BKGD PIN 10 CYCLES 10 CYCLES HOST SAMPLES BKGD PIN EARLIEST START OF NEXT BIT Figure 18-4. BDM Target-to-Host Serial Bit Timing (Logic 0) MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 333 Development Support 18.2.3 BDC Commands BDC commands are sent serially from a host computer to the BKGD pin of the target HCS08 MCU. All commands and data are sent MSB-first using a custom BDC communications protocol. Active background mode commands require that the target MCU is currently in the active background mode while non-intrusive commands may be issued at any time whether the target MCU is in active background mode or running a user application program. Table 18-1 shows all HCS08 BDC commands, a shorthand description of their coding structure, and the meaning of each command. Coding Structure Nomenclature This nomenclature is used in Table 18-1 to describe the coding structure of the BDC commands. Commands begin with an 8-bit hexadecimal command code in the host-to-target direction (most significant bit first) / = separates parts of the command d = delay 16 target BDC clock cycles AAAA = a 16-bit address in the host-to-target direction RD = 8 bits of read data in the target-to-host direction WD = 8 bits of write data in the host-to-target direction RD16 = 16 bits of read data in the target-to-host direction WD16 = 16 bits of write data in the host-to-target direction SS = the contents of BDCSCR in the target-to-host direction (STATUS) CC = 8 bits of write data for BDCSCR in the host-to-target direction (CONTROL) RBKP = 16 bits of read data in the target-to-host direction (from BDCBKPT breakpoint register) WBKP = 16 bits of write data in the host-to-target direction (for BDCBKPT breakpoint register) MC9S08JM60 Series Data Sheet, Rev. 3 334 Freescale Semiconductor Development Support Table 18-1. BDC Command Summary Command Mnemonic SYNC ACK_ENABLE ACK_DISABLE BACKGROUND READ_STATUS WRITE_CONTROL READ_BYTE READ_BYTE_WS READ_LAST WRITE_BYTE WRITE_BYTE_WS READ_BKPT WRITE_BKPT GO TRACE1 TAGGO READ_A READ_CCR READ_PC READ_HX READ_SP READ_NEXT READ_NEXT_WS WRITE_A WRITE_CCR WRITE_PC WRITE_HX WRITE_SP WRITE_NEXT WRITE_NEXT_WS 1 Active BDM/ Non-intrusive Non-intrusive Non-intrusive Non-intrusive Non-intrusive Non-intrusive Non-intrusive Non-intrusive Non-intrusive Non-intrusive Non-intrusive Non-intrusive Non-intrusive Non-intrusive Active BDM Active BDM Active BDM Active BDM Active BDM Active BDM Active BDM Active BDM Active BDM Active BDM Active BDM Active BDM Active BDM Active BDM Active BDM Active BDM Active BDM n/a1 D5/d D6/d 90/d E4/SS C4/CC Coding Structure Description Request a timed reference pulse to determine target BDC communication speed Enable acknowledge protocol. Refer to Freescale document order no. HCS08RMv1/D. Disable acknowledge protocol. Refer to Freescale document order no. HCS08RMv1/D. Enter active background mode if enabled (ignore if ENBDM bit equals 0) Read BDC status from BDCSCR Write BDC controls in BDCSCR Read a byte from target memory Read a byte and report status Re-read byte from address just read and report status Write a byte to target memory Write a byte and report status Read BDCBKPT breakpoint register Write BDCBKPT breakpoint register Go to execute the user application program starting at the address currently in the PC Trace 1 user instruction at the address in the PC, then return to active background mode Same as GO but enable external tagging (HCS08 devices have no external tagging pin) Read accumulator (A) Read condition code register (CCR) Read program counter (PC) Read H and X register pair (H:X) Read stack pointer (SP) Increment H:X by one then read memory byte located at H:X Increment H:X by one then read memory byte located at H:X. Report status and data. Write accumulator (A) Write condition code register (CCR) Write program counter (PC) Write H and X register pair (H:X) Write stack pointer (SP) Increment H:X by one, then write memory byte located at H:X Increment H:X by one, then write memory byte located at H:X. Also report status. E0/AAAA/d/RD E1/AAAA/d/SS/RD E8/SS/RD C0/AAAA/WD/d C1/AAAA/WD/d/SS E2/RBKP C2/WBKP 08/d 10/d 18/d 68/d/RD 69/d/RD 6B/d/RD16 6C/d/RD16 6F/d/RD16 70/d/RD 71/d/SS/RD 48/WD/d 49/WD/d 4B/WD16/d 4C/WD16/d 4F/WD16/d 50/WD/d 51/WD/d/SS The SYNC command is a special operation that does not have a command code. MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 335 Development Support The SYNC command is unlike other BDC commands because the host does not necessarily know the correct communications speed to use for BDC communications until after it has analyzed the response to the SYNC command. To issue a SYNC command, the host: • Drives the BKGD pin low for at least 128 cycles of the slowest possible BDC clock (The slowest clock is normally the reference oscillator/64 or the self-clocked rate/64.) • Drives BKGD high for a brief speedup pulse to get a fast rise time (This speedup pulse is typically one cycle of the fastest clock in the system.) • Removes all drive to the BKGD pin so it reverts to high impedance • Monitors the BKGD pin for the sync response pulse The target, upon detecting the SYNC request from the host (which is a much longer low time than would ever occur during normal BDC communications): • Waits for BKGD to return to a logic high • Delays 16 cycles to allow the host to stop driving the high speedup pulse • Drives BKGD low for 128 BDC clock cycles • Drives a 1-cycle high speedup pulse to force a fast rise time on BKGD • Removes all drive to the BKGD pin so it reverts to high impedance The host measures the low time of this 128-cycle sync response pulse and determines the correct speed for subsequent BDC communications. Typically, the host can determine the correct communication speed within a few percent of the actual target speed and the communication protocol can easily tolerate speed errors of several percent. 18.2.4 BDC Hardware Breakpoint The BDC includes one relatively simple hardware breakpoint that compares the CPU address bus to a 16-bit match value in the BDCBKPT register. This breakpoint can generate a forced breakpoint or a tagged breakpoint. A forced breakpoint causes the CPU to enter active background mode at the first instruction boundary following any access to the breakpoint address. The tagged breakpoint causes the instruction opcode at the breakpoint address to be tagged so that the CPU will enter active background mode rather than executing that instruction if and when it reaches the end of the instruction queue. This implies that tagged breakpoints can only be placed at the address of an instruction opcode while forced breakpoints can be set at any address. The breakpoint enable (BKPTEN) control bit in the BDC status and control register (BDCSCR) is used to enable the breakpoint logic (BKPTEN = 1). When BKPTEN = 0, its default value after reset, the breakpoint logic is disabled and no BDC breakpoints are requested regardless of the values in other BDC breakpoint registers and control bits. The force/tag select (FTS) control bit in BDCSCR is used to select forced (FTS = 1) or tagged (FTS = 0) type breakpoints. The on-chip debug module (DBG) includes circuitry for two additional hardware breakpoints that are more flexible than the simple breakpoint in the BDC module. MC9S08JM60 Series Data Sheet, Rev. 3 336 Freescale Semiconductor Development Support 18.3 On-Chip Debug System (DBG) Because HCS08 devices do not have external address and data buses, the most important functions of an in-circuit emulator have been built onto the chip with the MCU. The debug system consists of an 8-stage FIFO that can store address or data bus information, and a flexible trigger system to decide when to capture bus information and what information to capture. The system relies on the single-wire background debug system to access debug control registers and to read results out of the eight stage FIFO. The debug module includes control and status registers that are accessible in the user’s memory map. These registers are located in the high register space to avoid using valuable direct page memory space. Most of the debug module’s functions are used during development, and user programs rarely access any of the control and status registers for the debug module. The one exception is that the debug system can provide the means to implement a form of ROM patching. This topic is discussed in greater detail in Section 18.3.6, “Hardware Breakpoints.” 18.3.1 Comparators A and B Two 16-bit comparators (A and B) can optionally be qualified with the R/W signal and an opcode tracking circuit. Separate control bits allow you to ignore R/W for each comparator. The opcode tracking circuitry optionally allows you to specify that a trigger will occur only if the opcode at the specified address is actually executed as opposed to only being read from memory into the instruction queue. The comparators are also capable of magnitude comparisons to support the inside range and outside range trigger modes. Comparators are disabled temporarily during all BDC accesses. The A comparator is always associated with the 16-bit CPU address. The B comparator compares to the CPU address or the 8-bit CPU data bus, depending on the trigger mode selected. Because the CPU data bus is separated into a read data bus and a write data bus, the RWAEN and RWA control bits have an additional purpose, in full address plus data comparisons they are used to decide which of these buses to use in the comparator B data bus comparisons. If RWAEN = 1 (enabled) and RWA = 0 (write), the CPU’s write data bus is used. Otherwise, the CPU’s read data bus is used. The currently selected trigger mode determines what the debugger logic does when a comparator detects a qualified match condition. A match can cause: • Generation of a breakpoint to the CPU • Storage of data bus values into the FIFO • Starting to store change-of-flow addresses into the FIFO (begin type trace) • Stopping the storage of change-of-flow addresses into the FIFO (end type trace) 18.3.2 Bus Capture Information and FIFO Operation The usual way to use the FIFO is to setup the trigger mode and other control options, then arm the debugger. When the FIFO has filled or the debugger has stopped storing data into the FIFO, you would read the information out of it in the order it was stored into the FIFO. Status bits indicate the number of words of valid information that are in the FIFO as data is stored into it. If a trace run is manually halted by writing 0 to ARM before the FIFO is full (CNT = 1:0:0:0), the information is shifted by one position and MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 337 Development Support the host must perform ((8 – CNT) – 1) dummy reads of the FIFO to advance it to the first significant entry in the FIFO. In most trigger modes, the information stored in the FIFO consists of 16-bit change-of-flow addresses. In these cases, read DBGFH then DBGFL to get one coherent word of information out of the FIFO. Reading DBGFL (the low-order byte of the FIFO data port) causes the FIFO to shift so the next word of information is available at the FIFO data port. In the event-only trigger modes (see Section 18.3.5, “Trigger Modes”), 8-bit data information is stored into the FIFO. In these cases, the high-order half of the FIFO (DBGFH) is not used and data is read out of the FIFO by simply reading DBGFL. Each time DBGFL is read, the FIFO is shifted so the next data value is available through the FIFO data port at DBGFL. In trigger modes where the FIFO is storing change-of-flow addresses, there is a delay between CPU addresses and the input side of the FIFO. Because of this delay, if the trigger event itself is a change-of-flow address or a change-of-flow address appears during the next two bus cycles after a trigger event starts the FIFO, it will not be saved into the FIFO. In the case of an end-trace, if the trigger event is a change-of-flow, it will be saved as the last change-of-flow entry for that debug run. The FIFO can also be used to generate a profile of executed instruction addresses when the debugger is not armed. When ARM = 0, reading DBGFL causes the address of the most-recently fetched opcode to be saved in the FIFO. To use the profiling feature, a host debugger would read addresses out of the FIFO by reading DBGFH then DBGFL at regular periodic intervals. The first eight values would be discarded because they correspond to the eight DBGFL reads needed to initially fill the FIFO. Additional periodic reads of DBGFH and DBGFL return delayed information about executed instructions so the host debugger can develop a profile of executed instruction addresses. 18.3.3 Change-of-Flow Information To minimize the amount of information stored in the FIFO, only information related to instructions that cause a change to the normal sequential execution of instructions is stored. With knowledge of the source and object code program stored in the target system, an external debugger system can reconstruct the path of execution through many instructions from the change-of-flow information stored in the FIFO. For conditional branch instructions where the branch is taken (branch condition was true), the source address is stored (the address of the conditional branch opcode). Because BRA and BRN instructions are not conditional, these events do not cause change-of-flow information to be stored in the FIFO. Indirect JMP and JSR instructions use the current contents of the H:X index register pair to determine the destination address, so the debug system stores the run-time destination address for any indirect JMP or JSR. For interrupts, RTI, or RTS, the destination address is stored in the FIFO as change-of-flow information. 18.3.4 Tag vs. Force Breakpoints and Triggers Tagging is a term that refers to identifying an instruction opcode as it is fetched into the instruction queue, but not taking any other action until and unless that instruction is actually executed by the CPU. This distinction is important because any change-of-flow from a jump, branch, subroutine call, or interrupt causes some instructions that have been fetched into the instruction queue to be thrown away without being executed. MC9S08JM60 Series Data Sheet, Rev. 3 338 Freescale Semiconductor Development Support A force-type breakpoint waits for the current instruction to finish and then acts upon the breakpoint request. The usual action in response to a breakpoint is to go to active background mode rather than continuing to the next instruction in the user application program. The tag vs. force terminology is used in two contexts within the debug module. The first context refers to breakpoint requests from the debug module to the CPU. The second refers to match signals from the comparators to the debugger control logic. When a tag-type break request is sent to the CPU, a signal is entered into the instruction queue along with the opcode so that if/when this opcode ever executes, the CPU will effectively replace the tagged opcode with a BGND opcode so the CPU goes to active background mode rather than executing the tagged instruction. When the TRGSEL control bit in the DBGT register is set to select tag-type operation, the output from comparator A or B is qualified by a block of logic in the debug module that tracks opcodes and only produces a trigger to the debugger if the opcode at the compare address is actually executed. There is separate opcode tracking logic for each comparator so more than one compare event can be tracked through the instruction queue at a time. 18.3.5 Trigger Modes The trigger mode controls the overall behavior of a debug run. The 4-bit TRG field in the DBGT register selects one of nine trigger modes. When TRGSEL = 1 in the DBGT register, the output of the comparator must propagate through an opcode tracking circuit before triggering FIFO actions. The BEGIN bit in DBGT chooses whether the FIFO begins storing data when the qualified trigger is detected (begin trace), or the FIFO stores data in a circular fashion from the time it is armed until the qualified trigger is detected (end trigger). A debug run is started by writing a 1 to the ARM bit in the DBGC register, which sets the ARMF flag and clears the AF and BF flags and the CNT bits in DBGS. A begin-trace debug run ends when the FIFO gets full. An end-trace run ends when the selected trigger event occurs. Any debug run can be stopped manually by writing a 0 to ARM or DBGEN in DBGC. In all trigger modes except event-only modes, the FIFO stores change-of-flow addresses. In event-only trigger modes, the FIFO stores data in the low-order eight bits of the FIFO. The BEGIN control bit is ignored in event-only trigger modes and all such debug runs are begin type traces. When TRGSEL = 1 to select opcode fetch triggers, it is not necessary to use R/W in comparisons because opcode tags would only apply to opcode fetches that are always read cycles. It would also be unusual to specify TRGSEL = 1 while using a full mode trigger because the opcode value is normally known at a particular address. The following trigger mode descriptions only state the primary comparator conditions that lead to a trigger. Either comparator can usually be further qualified with R/W by setting RWAEN (RWBEN) and the corresponding RWA (RWB) value to be matched against R/W. The signal from the comparator with optional R/W qualification is used to request a CPU breakpoint if BRKEN = 1 and TAG determines whether the CPU request will be a tag request or a force request. MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 339 Development Support A-Only — Trigger when the address matches the value in comparator A A OR B — Trigger when the address matches either the value in comparator A or the value in comparator B A Then B — Trigger when the address matches the value in comparator B but only after the address for another cycle matched the value in comparator A. There can be any number of cycles after the A match and before the B match. A AND B Data (Full Mode) — This is called a full mode because address, data, and R/W (optionally) must match within the same bus cycle to cause a trigger event. Comparator A checks address, the low byte of comparator B checks data, and R/W is checked against RWA if RWAEN = 1. The high-order half of comparator B is not used. In full trigger modes it is not useful to specify a tag-type CPU breakpoint (BRKEN = TAG = 1), but if you do, the comparator B data match is ignored for the purpose of issuing the tag request to the CPU and the CPU breakpoint is issued when the comparator A address matches. A AND NOT B Data (Full Mode) — Address must match comparator A, data must not match the low half of comparator B, and R/W must match RWA if RWAEN = 1. All three conditions must be met within the same bus cycle to cause a trigger. In full trigger modes it is not useful to specify a tag-type CPU breakpoint (BRKEN = TAG = 1), but if you do, the comparator B data match is ignored for the purpose of issuing the tag request to the CPU and the CPU breakpoint is issued when the comparator A address matches. Event-Only B (Store Data) — Trigger events occur each time the address matches the value in comparator B. Trigger events cause the data to be captured into the FIFO. The debug run ends when the FIFO becomes full. A Then Event-Only B (Store Data) — After the address has matched the value in comparator A, a trigger event occurs each time the address matches the value in comparator B. Trigger events cause the data to be captured into the FIFO. The debug run ends when the FIFO becomes full. Inside Range (A ≤ Address ≤ B) — A trigger occurs when the address is greater than or equal to the value in comparator A and less than or equal to the value in comparator B at the same time. Outside Range (Address < A or Address > B) — A trigger occurs when the address is either less than the value in comparator A or greater than the value in comparator B. MC9S08JM60 Series Data Sheet, Rev. 3 340 Freescale Semiconductor Development Support 18.3.6 Hardware Breakpoints The BRKEN control bit in the DBGC register may be set to 1 to allow any of the trigger conditions described in Section 18.3.5, “Trigger Modes,” to be used to generate a hardware breakpoint request to the CPU. TAG in DBGC controls whether the breakpoint request will be treated as a tag-type breakpoint or a force-type breakpoint. A tag breakpoint causes the current opcode to be marked as it enters the instruction queue. If a tagged opcode reaches the end of the pipe, the CPU executes a BGND instruction to go to active background mode rather than executing the tagged opcode. A force-type breakpoint causes the CPU to finish the current instruction and then go to active background mode. If the background mode has not been enabled (ENBDM = 1) by a serial WRITE_CONTROL command through the BKGD pin, the CPU will execute an SWI instruction instead of going to active background mode. 18.4 Register Definition This section contains the descriptions of the BDC and DBG registers and control bits. Refer to the high-page register summary in the device overview chapter of this data sheet for the absolute address assignments for all DBG registers. This section refers to registers and control bits only by their names. A Freescale-provided equate or header file is used to translate these names into the appropriate absolute addresses. 18.4.1 BDC Registers and Control Bits The BDC has two registers: • The BDC status and control register (BDCSCR) is an 8-bit register containing control and status bits for the background debug controller. • The BDC breakpoint match register (BDCBKPT) holds a 16-bit breakpoint match address. These registers are accessed with dedicated serial BDC commands and are not located in the memory space of the target MCU (so they do not have addresses and cannot be accessed by user programs). Some of the bits in the BDCSCR have write limitations; otherwise, these registers may be read or written at any time. For example, the ENBDM control bit may not be written while the MCU is in active background mode. (This prevents the ambiguous condition of the control bit forbidding active background mode while the MCU is already in active background mode.) Also, the four status bits (BDMACT, WS, WSF, and DVF) are read-only status indicators and can never be written by the WRITE_CONTROL serial BDC command. The clock switch (CLKSW) control bit may be read or written at any time. MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 341 Development Support 18.4.1.1 BDC Status and Control Register (BDCSCR) This register can be read or written by serial BDC commands (READ_STATUS and WRITE_CONTROL) but is not accessible to user programs because it is not located in the normal memory map of the MCU. 7 6 5 4 3 2 1 0 R ENBDM W Normal Reset Reset in Active BDM: 0 1 BDMACT BKPTEN 0 1 0 0 FTS 0 0 CLKSW 0 1 WS WSF DVF 0 0 0 0 0 0 = Unimplemented or Reserved Figure 18-5. BDC Status and Control Register (BDCSCR) Table 18-2. BDCSCR Register Field Descriptions Field 7 ENBDM Description Enable BDM (Permit Active Background Mode) — Typically, this bit is written to 1 by the debug host shortly after the beginning of a debug session or whenever the debug host resets the target and remains 1 until a normal reset clears it. 0 BDM cannot be made active (non-intrusive commands still allowed) 1 BDM can be made active to allow active background mode commands Background Mode Active Status — This is a read-only status bit. 0 BDM not active (user application program running) 1 BDM active and waiting for serial commands BDC Breakpoint Enable — If this bit is clear, the BDC breakpoint is disabled and the FTS (force tag select) control bit and BDCBKPT match register are ignored. 0 BDC breakpoint disabled 1 BDC breakpoint enabled Force/Tag Select — When FTS = 1, a breakpoint is requested whenever the CPU address bus matches the BDCBKPT match register. When FTS = 0, a match between the CPU address bus and the BDCBKPT register causes the fetched opcode to be tagged. If this tagged opcode ever reaches the end of the instruction queue, the CPU enters active background mode rather than executing the tagged opcode. 0 Tag opcode at breakpoint address and enter active background mode if CPU attempts to execute that instruction 1 Breakpoint match forces active background mode at next instruction boundary (address need not be an opcode) Select Source for BDC Communications Clock — CLKSW defaults to 0, which selects the alternate BDC clock source. 0 Alternate BDC clock source 1 MCU bus clock 6 BDMACT 5 BKPTEN 4 FTS 3 CLKSW MC9S08JM60 Series Data Sheet, Rev. 3 342 Freescale Semiconductor Development Support Table 18-2. BDCSCR Register Field Descriptions (continued) Field 2 WS Description Wait or Stop Status — When the target CPU is in wait or stop mode, most BDC commands cannot function. However, the BACKGROUND command can be used to force the target CPU out of wait or stop and into active background mode where all BDC commands work. Whenever the host forces the target MCU into active background mode, the host should issue a READ_STATUS command to check that BDMACT = 1 before attempting other BDC commands. 0 Target CPU is running user application code or in active background mode (was not in wait or stop mode when background became active) 1 Target CPU is in wait or stop mode, or a BACKGROUND command was used to change from wait or stop to active background mode Wait or Stop Failure Status — This status bit is set if a memory access command failed due to the target CPU executing a wait or stop instruction at or about the same time. The usual recovery strategy is to issue a BACKGROUND command to get out of wait or stop mode into active background mode, repeat the command that failed, then return to the user program. (Typically, the host would restore CPU registers and stack values and re-execute the wait or stop instruction.) 0 Memory access did not conflict with a wait or stop instruction 1 Memory access command failed because the CPU entered wait or stop mode Data Valid Failure Status — This status bit is not used in the MC9S08JM60 Series because it does not have any slow access memory. 0 Memory access did not conflict with a slow memory access 1 Memory access command failed because CPU was not finished with a slow memory access 1 WSF 0 DVF 18.4.1.2 BDC Breakpoint Match Register (BDCBKPT) This 16-bit register holds the address for the hardware breakpoint in the BDC. The BKPTEN and FTS control bits in BDCSCR are used to enable and configure the breakpoint logic. Dedicated serial BDC commands (READ_BKPT and WRITE_BKPT) are used to read and write the BDCBKPT register but is not accessible to user programs because it is not located in the normal memory map of the MCU. Breakpoints are normally set while the target MCU is in active background mode before running the user application program. For additional information about setup and use of the hardware breakpoint logic in the BDC, refer to Section 18.2.4, “BDC Hardware Breakpoint.” 18.4.2 System Background Debug Force Reset Register (SBDFR) This register contains a single write-only control bit. A serial background mode command such as WRITE_BYTE must be used to write to SBDFR. Attempts to write this register from a user program are ignored. Reads always return 0x00. 7 6 5 4 3 2 1 0 R W Reset 0 0 0 0 0 0 0 0 BDFR1 0 0 0 0 0 0 0 0 = Unimplemented or Reserved 1 BDFR is writable only through serial background mode debug commands, not from user programs. Figure 18-6. System Background Debug Force Reset Register (SBDFR) MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 343 Development Support Table 18-3. SBDFR Register Field Description Field 0 BDFR Description Background Debug Force Reset — A serial active background mode command such as WRITE_BYTE allows an external debug host to force a target system reset. Writing 1 to this bit forces an MCU reset. This bit cannot be written from a user program. 18.4.3 DBG Registers and Control Bits The debug module includes nine bytes of register space for three 16-bit registers and three 8-bit control and status registers. These registers are located in the high register space of the normal memory map so they are accessible to normal application programs. These registers are rarely if ever accessed by normal user application programs with the possible exception of a ROM patching mechanism that uses the breakpoint logic. 18.4.3.1 Debug Comparator A High Register (DBGCAH) This register contains compare value bits for the high-order eight bits of comparator A. This register is forced to 0x00 at reset and can be read at any time or written at any time unless ARM = 1. 18.4.3.2 Debug Comparator A Low Register (DBGCAL) This register contains compare value bits for the low-order eight bits of comparator A. This register is forced to 0x00 at reset and can be read at any time or written at any time unless ARM = 1. 18.4.3.3 Debug Comparator B High Register (DBGCBH) This register contains compare value bits for the high-order eight bits of comparator B. This register is forced to 0x00 at reset and can be read at any time or written at any time unless ARM = 1. 18.4.3.4 Debug Comparator B Low Register (DBGCBL) This register contains compare value bits for the low-order eight bits of comparator B. This register is forced to 0x00 at reset and can be read at any time or written at any time unless ARM = 1. 18.4.3.5 Debug FIFO High Register (DBGFH) This register provides read-only access to the high-order eight bits of the FIFO. Writes to this register have no meaning or effect. In the event-only trigger modes, the FIFO only stores data into the low-order byte of each FIFO word, so this register is not used and will read 0x00. Reading DBGFH does not cause the FIFO to shift to the next word. When reading 16-bit words out of the FIFO, read DBGFH before reading DBGFL because reading DBGFL causes the FIFO to advance to the next word of information. MC9S08JM60 Series Data Sheet, Rev. 3 344 Freescale Semiconductor Development Support 18.4.3.6 Debug FIFO Low Register (DBGFL) This register provides read-only access to the low-order eight bits of the FIFO. Writes to this register have no meaning or effect. Reading DBGFL causes the FIFO to shift to the next available word of information. When the debug module is operating in event-only modes, only 8-bit data is stored into the FIFO (high-order half of each FIFO word is unused). When reading 8-bit words out of the FIFO, simply read DBGFL repeatedly to get successive bytes of data from the FIFO. It isn’t necessary to read DBGFH in this case. Do not attempt to read data from the FIFO while it is still armed (after arming but before the FIFO is filled or ARMF is cleared) because the FIFO is prevented from advancing during reads of DBGFL. This can interfere with normal sequencing of reads from the FIFO. Reading DBGFL while the debugger is not armed causes the address of the most-recently fetched opcode to be stored to the last location in the FIFO. By reading DBGFH then DBGFL periodically, external host software can develop a profile of program execution. After eight reads from the FIFO, the ninth read will return the information that was stored as a result of the first read. To use the profiling feature, read the FIFO eight times without using the data to prime the sequence and then begin using the data to get a delayed picture of what addresses were being executed. The information stored into the FIFO on reads of DBGFL (while the FIFO is not armed) is the address of the most-recently fetched opcode. MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 345 Development Support 18.4.3.7 Debug Control Register (DBGC) This register can be read or written at any time. 7 6 5 4 3 2 1 0 R DBGEN W Reset 0 0 0 0 0 0 0 0 ARM TAG BRKEN RWA RWAEN RWB RWBEN Figure 18-7. Debug Control Register (DBGC) Table 18-4. DBGC Register Field Descriptions Field 7 DBGEN 6 ARM Description Debug Module Enable — Used to enable the debug module. DBGEN cannot be set to 1 if the MCU is secure. 0 DBG disabled 1 DBG enabled Arm Control — Controls whether the debugger is comparing and storing information in the FIFO. A write is used to set this bit (and ARMF) and completion of a debug run automatically clears it. Any debug run can be manually stopped by writing 0 to ARM or to DBGEN. 0 Debugger not armed 1 Debugger armed Tag/Force Select — Controls whether break requests to the CPU will be tag or force type requests. If BRKEN = 0, this bit has no meaning or effect. 0 CPU breaks requested as force type requests 1 CPU breaks requested as tag type requests Break Enable — Controls whether a trigger event will generate a break request to the CPU. Trigger events can cause information to be stored in the FIFO without generating a break request to the CPU. For an end trace, CPU break requests are issued to the CPU when the comparator(s) and R/W meet the trigger requirements. For a begin trace, CPU break requests are issued when the FIFO becomes full. TRGSEL does not affect the timing of CPU break requests. 0 CPU break requests not enabled 1 Triggers cause a break request to the CPU R/W Comparison Value for Comparator A — When RWAEN = 1, this bit determines whether a read or a write access qualifies comparator A. When RWAEN = 0, RWA and the R/W signal do not affect comparator A. 0 Comparator A can only match on a write cycle 1 Comparator A can only match on a read cycle Enable R/W for Comparator A — Controls whether the level of R/W is considered for a comparator A match. 0 R/W is not used in comparison A 1 R/W is used in comparison A R/W Comparison Value for Comparator B — When RWBEN = 1, this bit determines whether a read or a write access qualifies comparator B. When RWBEN = 0, RWB and the R/W signal do not affect comparator B. 0 Comparator B can match only on a write cycle 1 Comparator B can match only on a read cycle Enable R/W for Comparator B — Controls whether the level of R/W is considered for a comparator B match. 0 R/W is not used in comparison B 1 R/W is used in comparison B 5 TAG 4 BRKEN 3 RWA 2 RWAEN 1 RWB 0 RWBEN MC9S08JM60 Series Data Sheet, Rev. 3 346 Freescale Semiconductor Development Support 18.4.3.8 Debug Trigger Register (DBGT) This register can be read any time, but may be written only if ARM = 0, except bits 4 and 5 are hard-wired to 0s. 7 6 5 4 3 2 1 0 R TRGSEL W Reset 0 0 BEGIN 0 0 TRG3 TRG2 0 TRG1 0 TRG0 0 0 0 0 = Unimplemented or Reserved Figure 18-8. Debug Trigger Register (DBGT) Table 18-5. DBGT Register Field Descriptions Field 7 TRGSEL Description Trigger Type — Controls whether the match outputs from comparators A and B are qualified with the opcode tracking logic in the debug module. If TRGSEL is set, a match signal from comparator A or B must propagate through the opcode tracking logic and a trigger event is only signalled to the FIFO logic if the opcode at the match address is actually executed. 0 Trigger on access to compare address (force) 1 Trigger if opcode at compare address is executed (tag) Begin/End Trigger Select — Controls whether the FIFO starts filling at a trigger or fills in a circular manner until a trigger ends the capture of information. In event-only trigger modes, this bit is ignored and all debug runs are assumed to be begin traces. 0 Data stored in FIFO until trigger (end trace) 1 Trigger initiates data storage (begin trace) Select Trigger Mode — Selects one of nine triggering modes, as described below. 0000 A-only 0001 A OR B 0010 A Then B 0011 Event-only B (store data) 0100 A then event-only B (store data) 0101 A AND B data (full mode) 0110 A AND NOT B data (full mode) 0111 Inside range: A ≤ address ≤ B 1000 Outside range: address < A or address > B 1001 – 1111 (No trigger) 6 BEGIN 3:0 TRG[3:0] MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 347 Development Support 18.4.3.9 Debug Status Register (DBGS) This is a read-only status register. 7 6 5 4 3 2 1 0 R W Reset AF BF ARMF 0 CNT3 CNT2 CNT1 CNT0 0 0 0 0 0 0 0 0 = Unimplemented or Reserved Figure 18-9. Debug Status Register (DBGS) Table 18-6. DBGS Register Field Descriptions Field 7 AF Description Trigger Match A Flag — AF is cleared at the start of a debug run and indicates whether a trigger match A condition was met since arming. 0 Comparator A has not matched 1 Comparator A match Trigger Match B Flag — BF is cleared at the start of a debug run and indicates whether a trigger match B condition was met since arming. 0 Comparator B has not matched 1 Comparator B match Arm Flag — While DBGEN = 1, this status bit is a read-only image of ARM in DBGC. This bit is set by writing 1 to the ARM control bit in DBGC (while DBGEN = 1) and is automatically cleared at the end of a debug run. A debug run is completed when the FIFO is full (begin trace) or when a trigger event is detected (end trace). A debug run can also be ended manually by writing 0 to ARM or DBGEN in DBGC. 0 Debugger not armed 1 Debugger armed FIFO Valid Count — These bits are cleared at the start of a debug run and indicate the number of words of valid data in the FIFO at the end of a debug run. The value in CNT does not decrement as data is read out of the FIFO. The external debug host is responsible for keeping track of the count as information is read out of the FIFO. 0000 Number of valid words in FIFO = No valid data 0001 Number of valid words in FIFO = 1 0010 Number of valid words in FIFO = 2 0011 Number of valid words in FIFO = 3 0100 Number of valid words in FIFO = 4 0101 Number of valid words in FIFO = 5 0110 Number of valid words in FIFO = 6 0111 Number of valid words in FIFO = 7 1000 Number of valid words in FIFO = 8 6 BF 5 ARMF 3:0 CNT[3:0] MC9S08JM60 Series Data Sheet, Rev. 3 348 Freescale Semiconductor Appendix A Electrical Characteristics A.1 Introduction This appendix contains electrical and timing specifications for the MC9S08JM60 series of microcontrollers available at the time of publication. A.2 Parameter Classification The electrical parameters shown in this supplement are guaranteed by various methods. To give the customer a better understanding the following classification is used and the parameters are tagged accordingly in the tables where appropriate: Table A-1. Parameter Classifications P C Those parameters are guaranteed during production testing on each individual device. Those parameters are achieved by the design characterization by measuring a statistically relevant sample size across process variations. Those parameters are achieved by design characterization on a small sample size from typical devices under typical conditions unless otherwise noted. All values shown in the typical column are within this category. Those parameters are derived mainly from simulations. T D NOTE The classification is shown in the column labeled “C” in the parameter tables where appropriate. A.3 Absolute Maximum Ratings Absolute maximum ratings are stress ratings only, and functional operation at the maxima is not guaranteed. Stress beyond the limits specified in Table A-2 may affect device reliability or cause permanent damage to the device. For functional operating conditions, refer to the remaining tables in this section. This device contains circuitry protecting against damage due to high static voltage or electrical fields; however, it is advised that normal precautions be taken to avoid application of any voltages higher than maximum-rated voltages to this high-impedance circuit. Reliability of operation is enhanced if unused inputs are tied to an appropriate logic voltage level (for instance, either VSS or VDD). MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 349 Appendix A Electrical Characteristics Table A-2. Absolute Maximum Ratings Rating Supply voltage Input voltage Instantaneous maximum current Single pin limit (applies to all port pins)1, 2, 3 Maximum current into VDD Storage temperature 1 Symbol VDD VIn ID IDD Tstg Value – 0.3 to + 5.8 – 0.3 to VDD + 0.3 ± 25 120 –55 to +150 Unit V V mA mA °C Input must be current limited to the value specified. To determine the value of the required current-limiting resistor, calculate resistance values for positive (VDD) and negative (VSS) clamp voltages, then use the larger of the two resistance values. 2 All functional non-supply pins are internally clamped to VSS and VDD. 3 Power supply must maintain regulation within operating VDD range during instantaneous and operating maximum current conditions. If positive injection current (VIn > VDD) is greater than IDD, the injection current may flow out of VDD and could result in external power supply going out of regulation. Ensure external VDD load will shunt current greater than maximum injection current. This will be the greatest risk when the MCU is not consuming power. Examples are: if no system clock is present, or if the clock rate is very low which would reduce overall power consumption. A.4 Thermal Characteristics This section provides information about operating temperature range, power dissipation, and package thermal resistance. Power dissipation on I/O pins is usually small compared to the power dissipation in on-chip logic and it is user-determined rather than being controlled by the MCU design. In order to take PI/O into account in power calculations, determine the difference between actual pin voltage and VSS or VDD and multiply by the pin current for each I/O pin. Except in cases of unusually high pin current (heavy loads), the difference between pin voltage and VSS or VDD will be very small. Table A-3. Thermal Characteristics Num 1 2 C Rating Symbol TA TJ Value –40 to 85 135 Unit °C °C Temp. Code C T Operating temperature range (packaged) D Maximum junction temperature Thermal resistance Single layer board 64-pin QFP 64-pin LQFP 48-pin QFN 44-pin LQFP Four layer board 64-pin QFP 64-pin LQFP 48-pin QFN 44-pin LQFP 3 T θJA 55 73 84 71 41 54 28 49 °C/W — MC9S08JM60 Series Data Sheet, Rev. 3 350 Freescale Semiconductor Appendix A Electrical Characteristics The average chip-junction temperature (TJ) in °C can be obtained from: TJ = TA + (PD × θJA) Eqn. A-1 where: TA = Ambient temperature, °C θJA = Package thermal resistance, junction-to-ambient, °C/W PD = Pint + PI/O Pint = IDD × VDD, Watts — chip internal power PI/O = Power dissipation on input and output pins — user determined For most applications, PI/O VDD VIN VDD VIN VDD) is greater than IDD, the injection current may flow out of VDD and could result in external power supply going out of regulation. Ensure external VDD load will shunt current greater than maximum injection current. This will be the greatest risk when the MCU is not consuming power. Examples are: if no system clock is present, or if clock rate is very low (which would reduce overall power consumption). All functional non-supply pins are internally clamped to VSS and VDD. Input must be current limited to the value specified. To determine the value of the required current-limiting resistor, calculate resistance values for positive and negative clamp voltages, then use the larger of the two values. The RESET pin does not have a clamp diode to VDD. Do not drive this pin above VDD. MC9S08JM60 Series Data Sheet, Rev. 3 354 Freescale Semiconductor Appendix A Electrical Characteristics Typical VOL v s. IOL AT VDD = 5V 0.7 0.6 0.5 Typical V OL v s. IOL A T V DD = 3 V 1.4 1.2 1.0 Hot (85°C) Room (25°C) Cold (-40°C) Hot (85°C) Room (25°C) Cold (-40°C) VOL (v) 0.4 0.3 0.2 0.1 0.0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 VOL (v) 0.8 0.6 0.4 0.2 0.0 0.0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 IOL (mA) IOL (mA) Figure A-1. Typical Low-side Drive (sink) characteristics – High Drive (PTxDSn = 1) T ypical V O L v s. I O L AT V DD = 5 V 0.8 0.7 0.6 Typical V OL v s. IOL AT V DD = 3 V Hot (85°C) Room (25°C) Cold (-40°C) 0.8 0.7 0.6 Hot (85°C) Room (25°C) Cold (-40°C) VOL (v) 0.5 0.4 0.3 0.2 0.1 0.0 0 1 2 3 4 5 V OL (v) 0.5 0.4 0.3 0.2 0.1 0.0 0 1 2 3 IOL (m A) IOL (mA) Figure A-2. Typical Low-side Drive (sink) characteristics – Low Drive (PTxDSn = 0) Typical VDD - VOH vs. IOH A VDD = 5V T 0.8 1.2 Typical VDD - VOH vs. IOH AT VDD = 3V Hot (85°C) Room (25°C) Cold (-40°C) 1.0 Hot (85°C) Room (25°C) Cold (-40°C) VDD - VOH (v) VDD - VOH (v) 0.6 0.4 0.2 0.0 0.8 0.6 0.4 0.2 0 -1 -2 -3 -4 -5 -6 -7 -8 -9 -10 -11 -12 -13 -14 -15 0.0 0 -1 -2 -3 -4 -5 -6 -7 -8 -9 -10 -11 -12 -13 -14 -15 IOH (mA) IOH (mA) Figure A-3. Typical High-side Drive (source) characteristics – High Drive (PTxDSn = 1) MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 355 Appendix A Electrical Characteristics Typical VDD - VOH vs. IOH AT VDD= 5V 1.2 1.0 Hot (85°C) Typical VDD - VOH vs. IOH AT VDD = 3V 1.2 1.0 Hot (85°C) Room (25°C) Cold (-40°C) VDD - VOH (v) VDD - VOH (v) -2 -3 -4 -5 Room(25°C) Cold (-40°C) 0.8 0.6 0.4 0.2 0.0 0 0.8 0.6 0.4 0.2 0.0 -1 0 -1 IOH(mA) IOH (mA) -2 -3 Figure A-4. Typical High-side Drive (source) characteristics – Low Drive (PTxDSn = 0) MC9S08JM60 Series Data Sheet, Rev. 3 356 Freescale Semiconductor Appendix A Electrical Characteristics A.7 Num 1 C C Supply Current Characteristics Table A-7. Supply Current Characteristics Parameter Run supply current3 measured at (Core clock = 2 MHz, fBus = 1 MHz, BLPE mode) Run supply current3 measured at (Core clock = 8 MHz, fBus = 4 MHz, FBE mode) Run supply current3 measured at (Core clock = 48 MHz, fBus = 24 MHz, PEE mode) Stop2 mode supply current –40 °C 25 °C 85 °C –40 °C 25 °C 85 °C Stop3 mode supply current –40 °C 25 °C 85 °C –40 °C 25 °C 85 °C Adder to stop2 or stop3 for RTC enabled4, 25°C 5 S3IDD 3 0.90 0.90 3 3 20 3 3 20 μA 5 S2IDD 3 0.80 0.80 3 3 20 3 3 20 μA RIDD Symbol VDD (V) 5 3 5 3 5 3 Typical1 1.1 0.8 4.9 4.3 23 22 Max2 1.6 mA 1.5 8 mA 7 30 mA 30 Unit 2 P 3 C 4 P μA 5 P μA 6 P Adder to stop3 for LVD enabled (LVDE = LVDSE = 1) Adder to stop3 for oscillator enabled5 (ERCLKEN = 1 and EREFSTEN = 1) USB module enable current6 USB suspend current7 ΔISRTC 5 3 5 3 5 3 5 5 300 300 110 90 5 5 1.5 270 500 nA nA μA μA μA μA mA μA 7 P ΔISLVD 8 9 10 1 2 P T T ΔISOSC ΔIUSBE ISUSP Typicals are measured at 25°C. Values given here are preliminary estimates prior to completing characterization. 3 All modules except USB and ADC active, Oscillator disabled (ERCLKEN = 0), using external clock resource for input, and does not include any dc loads on port pins. 4 Most customers are expected to find that auto-wakeup from stop2 or stop3 can be used instead of the higher current wait mode. Wait mode typical is 560 μA at 5 V and 422 μA at 3V with fBus = 1 MHz. 5 Values given under the following conditions: low range operation (RANGE = 0), low power mode (HGO = 0). MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 357 Appendix A Electrical Characteristics 6 Here USB module is enabled and clocked at 48 MHz (USBEN = 1, USBVREN =1, USBPHYEN = 1 and USBPU = 1), and D+ and D– pull down by two 15.1kΩ resisters independently. The current consumption may be much higher when the packets are being transmitted through the attached cable. 7 MCU enters into Stop3 mode, USB bus in idle state. The USB suspend current will be dominated by the D+ pull up resister. A.8 Num 1 2 3 4 5 6 7 Analog Comparator (ACMP) Electricals Table A-8. Analog Comparator Electrical Specifications C — D D D D D D Supply voltage Supply current (active) Analog input voltage Analog input offset voltage Analog Comparator hysteresis Analog input leakage current Analog Comparator initialization delay Rating Symbol VDD IDDAC VAIN VAIO VH IALKG tAINIT — — 3.0 Min 2.7 — VSS – 0.3 Typical — 20 — 20 6.0 Max 5.5 35 VDD 40 20.0 1.0 1.0 Unit V μA V mV mV μA μs A.9 ADC Characteristics Table A-9. 5 Volt 12-bit ADC Operating Conditions Conditions Absolute Symb VDDAD ΔVDDAD ΔVSSAD VREFH VREFL VADIN CADIN RADIN 12 bit mode fADCK > 4 MHz fADCK < 4 MHz Min 2.7 –100 –100 2.7 VSSAD VREFL — — Typ1 — 0 0 VDDAD VSSAD — 4.5 3 Max 5.5 +100 +100 VDDAD VSSAD VREFH 5.5 5 Unit V mV mV V V V pF kΩ Comment Characteristic Supply voltage Ground voltage Ref Voltage High Ref Voltage Low Input Voltage Input Capacitance Input Resistance Delta to VDD (VDD-VDDAD)2 Delta to VSS (VSS-VSSAD)2 — — RAS — — — — — — — — 2 5 kΩ 5 10 10 External to MCU Analog Source Resistance 10 bit mode fADCK > 4 MHz fADCK < 4 MHz 8 bit mode (all valid fADCK) MC9S08JM60 Series Data Sheet, Rev. 3 358 Freescale Semiconductor Appendix A Electrical Characteristics Table A-9. 5 Volt 12-bit ADC Operating Conditions (continued) Characteristic ADC Conversion Clock Freq. 1 Conditions High Speed (ADLPC=0) Low Power (ADLPC=1) Symb Min 0.4 Typ1 — — Max 8.0 Unit Comment fADCK MHz 0.4 4.0 Typical values assume VDDAD = 5.0 V, Temp = 25°C, fADCK = 1.0 MHz unless otherwise stated. Typical values are for reference only and are not tested in production. 2 DC potential difference. SIMPLIFIED INPUT PIN EQUIVALENT CIRCUIT ZAS RAS VADIN VAS Pad leakage due to input protection ZADIN SIMPLIFIED CHANNEL SELECT CIRCUIT RADIN ADC SAR ENGINE + – + – CAS RADIN INPUT PIN RADIN INPUT PIN RADIN CADIN INPUT PIN Figure A-5. ADC Input Impedance Equivalency Diagram MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 359 Appendix A Electrical Characteristics Table A-10. 5 Volt 12-bit ADC Characteristics (VREFH = VDDAD, VREFL = VSSAD) Characteristic Supply Current ADLPC=1 ADLSMP=1 ADCO=1 Supply Current ADLPC=1 ADLSMP=0 ADCO=1 Supply Current ADLPC=0 ADLSMP=1 ADCO=1 Supply Current ADLPC=0 ADLSMP=0 ADCO=1 Supply Current ADC Asynchronous Clock Source Conversion Time (Including sample time) Sample Time Long Sample (ADLSMP=1) Total Unadjusted Error 12 bit mode 10 bit mode 8 bit mode 12 bit mode Differential Non-Linearity 10 bit mode3 8 bit mode2 12 bit mode Integral Non-Linearity 10 bit mode 8 bit mode 12 bit mode Zero-Scale Error 10 bit mode 8 bit mode T P T T P T T T T T P T EZS INL DNL ETUE Stop, Reset, Module Off High Speed (ADLPC=0) T Low Power (ADLPC=1) Short Sample (ADLSMP=0) T Long Sample (ADLSMP=1) Short Sample (ADLSMP=0) T tADS tADC fADACK Conditions C Symb Min Typ1 Max Unit Comment T IDDAD — 133 — μA T IDDAD — 218 — μA T IDDAD — 327 — μA T IDDAD — 0.582 1 mA IDDAD — 2 1.25 — — — — — — — — — — — — — — — — 0.011 3.3 2 20 40 3.5 23.5 ±3.0 ±1 ±0.5 ±1.75 ±0.5 ±0.3 ±1.5 ±0.5 ±0.3 ±1.5 ±0.5 ±0.5 1 5 μA MHz tADACK = 1/fADACK 3.3 — — — — ±10.0 ±2.5 ±1.0 ±4.0 ±1.0 ±0.5 ±4.0 ±1.0 ±0.5 ±6.0 ±1.5 ±0.5 LSB2 LSB2 LSB2 LSB2 ADCK cycles ADCK cycles See Table 10.13 for conversion time variances Includes quantization VADIN = VSSAD MC9S08JM60 Series Data Sheet, Rev. 3 360 Freescale Semiconductor Appendix A Electrical Characteristics Table A-10. 5 Volt 12-bit ADC Characteristics (VREFH = VDDAD, VREFL = VSSAD) (continued) Characteristic Conditions 12 bit mode Full-Scale Error 10 bit mode 8 bit mode 12 bit mode Quantization Error 10 bit mode 8 bit mode 12 bit mode Input Leakage Error 10 bit mode 8 bit mode Temp Sensor Voltage 25°C –40 °C — 25 °C 25 °C — 125 °C D m — 3.638 — D VTEMP25 D EIL D EQ C T P T EFS Symb Min — — — — — — — — — — — Typ1 ±1 ±0.5 ±0.5 –1 to 0 — — ±1 ±0.2 ±0.1 1.396 3.266 Max ±4.0 ±1 ±0.5 –1 to 0 ±0.5 ±0.5 ±10 ±2.5 ±1 — — V LSB2 Pad leakage4 * RAS LSB2 LSB2 VADIN = VDDAD Unit Comment Temp Sensor Slope 1 mV/°C Typical values assume VDDAD = 5.0 V, Temp = 25°C, fADCK = 1.0 MHz unless otherwise stated. Typical values are for reference only and are not tested in production. 2 1 LSB = (V N REFH – VREFL)/2 3 Monotonicity and no-missing-codes guaranteed in 10 bit and 8 bit modes. 4 Based on input pad leakage current. Refer to pad electricals. MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 361 Appendix A Electrical Characteristics A.10 Num C External Oscillator (XOSC) Characteristics Table A-11. Oscillator Electrical Specifications (Temperature Range = –40 to 85°C Ambient) Rating Oscillator crystal or resonator (EREFS = 1, ERCLKEN = 1) Low range (RANGE = 0) High range (RANGE = 1) FEE or FBE mode 2 High range (RANGE = 1) PEE or PBE mode 3 High range (RANGE = 1, HGO = 1) BLPE mode High range (RANGE = 1, HGO = 0) BLPE mode Symbol flo fhi-fll fhi-pll fhi-hgo fhi-lp C1, C2 RF Min 32 1 1 1 1 Typ1 — — — — — Max 38.4 5 16 16 8 Unit kHz MHz MHz MHz MHz 1 C 2 3 — Load capacitors — Feedback resistor Low range (32 kHz to 38.4 kHz) High range (1 MHz to 16 MHz) See crystal or resonator manufacturer’s recommendation. 10 1 — — — — — — 0 100 0 0 0 0 200 400 5 15 — — — — — — 0 10 20 — — — — 5 16 40 ms MΩ MΩ kΩ 4 Series resistor Low range, low gain (RANGE = 0, HGO = 0) Low range, high gain (RANGE = 0, HGO = 1) High range, low gain (RANGE = 1, HGO = 0) — High range, high gain (RANGE = 1, HGO = 1) ≥ 8 MHz 4 MHz 1 MHz Crystal start-up time 4 Low range, low gain (RANGE = 0, HGO = 0) Low range, high gain (RANGE = 0, HGO = 1) High range, low gain (RANGE = 1, HGO = 0)5 High range, high gain (RANGE = 1, HGO = 1)5 Square wave input clock frequency (EREFS = 0, ERCLKEN = 1) FEE or FBE mode 2 PEE or PBE mode 3 BLPE mode RS 5 T t t CSTL-LP CSTL-HGO t CSTH-LP t CSTH-HGO — — — — 0.03125 1 0 6 1 2 T fextal MHz MHz MHz Typical data was characterized at 3.0 V, 25°C or is recommended value. When MCG is configured for FEE or FBE mode, input clock source must be divided using RDIV to within the range of 31.25 kHz to 39.0625 kHz. 3 When MCG is configured for PEE or PBE mode, input clock source must be divided using RDIV to within the range of 1 MHz to 2 MHz. 4 This parameter is characterized and not tested on each device. Proper PC board layout procedures must be followed to achieve specifications. 5 4 MHz crystal MCU EXTAL XTAL RS RF C1 Crystal or Resonator C2 MC9S08JM60 Series Data Sheet, Rev. 3 362 Freescale Semiconductor Appendix A Electrical Characteristics A.11 Num C 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 1 2 MCG Specifications Table A-12. MCG Frequency Specifications (Temperature Range = –40 to 125°C Ambient) Rating Symbol fint_ft fint_ut fint_t tirefst 1 Min — 25 31.25 — 25.6 32 — — — — — — — 7.0 1.0 — — ±1.49 ±4.47 — — (3/5) x fint (16/5) x fint Typical 31.25 32.7 — 60 33.48 — ±0.1 ±0.2 +0.5 –1.0 ±0.5 — — 0.02 — — 0.5905 0.5665 — — — — — — Max — 41.66 39.0625 100 42.66 40 ±0.2 ±0.4 ±2 ±1 1 1 0.2 55.0 2.0 — — ±2.98 ±5.97 tfll_acquire+ 1075(1/fint_t) tpll_acquire+ 1075(1/fpll_ref) — — Unit kHz kHz kHz μs MHz MHz %fdco %fdco %fdco %fdco ms ms %fdco MHz MHz %fpll %fpll % % s s kHz kHz Internal reference frequency - factory trimmed at VDD = P 5 V and temperature = 25 °C P Average internal reference frequency – untrimmed 1 P Average internal reference frequency Q – user trimmed D Internal reference startup time — DCO output frequency range - untrimmed value provided for reference: fdco_ut = 1024 X fint_ut fdco_ut fdco_t Δfdco_res_t Δfdco_res_t Δfdco_t Δfdco_t tfll_acquire tpll_acquire CJitter fvco fpll_ref fpll_jitter_2ms fpll_jitter_625ns Dlock Dunl tfll_lock tpll_lock floc_low floc_high P DCO output frequency range - trimmed Resolution of trimmed DCO output frequency at fixed C voltage and temperature (using FTRIM) C P C Resolution of trimmed DCO output frequency at fixed voltage and temperature (not using FTRIM) Total deviation of trimmed DCO output frequency over voltage and temperature Total deviation of trimmed DCO output frequency over fixed voltage and temperature range of 0 –70 °C 3 C FLL acquisition time 2 D PLL acquisition time C Long term Jitter of DCO output clock (averaged over 2ms interval) 4 D VCO operating frequency D PLL reference frequency range T Long term accuracy of PLL output clock (averaged over 2 ms) T Jitter of PLL output clock measured over 625 ns D Lock entry frequency tolerance 6 D Lock exit frequency tolerance 7 D Lock time – FLL D Lock time – PLL D Loss of external clock minimum frequency – RANGE = 0 D Loss of external clock minimum frequency – RANGE = 1 TRIM register at default value (0x80) and FTRIM control bit at default value (0x0). This specification applies to any time the FLL reference source or reference divider is changed, trim value changed or changing from FLL disabled (BLPE, BLPI) to FLL enabled (FEI, FEE, FBE, FBI). If a crystal/resonator is being used as the reference, this specification assumes it is already running. 3 This specification applies to any time the PLL VCO divider or reference divider is changed, or changing from PLL disabled (BLPE, BLPI) to PLL enabled (PBE, PEE). If a crystal/resonator is being used as the reference, this specification assumes it is already running. MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 363 Appendix A Electrical Characteristics 4 Jitter is the average deviation from the programmed frequency measured over the specified interval at maximum fBUS. Measurements are made with the device powered by filtered supplies and clocked by a stable external clock signal. Noise injected into the FLL circuitry via VDD and VSS and variation in crystal oscillator frequency increase the CJitter percentage for a given interval. 5 Jitter measurements are based upon a 48 MHz MCGOUT clock frequency.. 6 Below Dlock minimum, the MCG is guaranteed to enter lock. Above Dlock maximum, the MCG will not enter lock. But if the MCG is already in lock, then the MCG may stay in lock. 7 Below Dunl minimum, the MCG will not exit lock if already in lock. Above Dunl maximum, the MCG is guaranteed to exit lock. o A.12 AC Characteristics This section describes ac timing characteristics for each peripheral system. A.12.1 Control Timing Table A-13. Control Timing Typ1 — Num 1 2 3 4 5 6 7 C Parameter Bus frequency (tcyc = 1/fBus) Internal low-power oscillator period External reset pulse width2 Reset low drive Active background debug mode latch setup time Active background debug mode latch hold time IRQ pulse width Asynchronous path2 Synchronous path3 Symbol fBus tLPO textrst trstdrv tMSSU tMSH tILIH, tIHIL Min dc 800 100 66 x tcyc 500 100 100 1.5 x tcyc 100 1.5 x tcyc — — Max 24 1500 — — — — Unit MHz μs ns ns ns ns ns — — 8 KBIPx pulse width Asynchronous path2 Synchronous path3 tILIH, tIHIL tRise, tFall 40 75 ns — — 11 35 — — ns 9 Port rise and fall time low output drive (PTxDS = 0), (load = 50 pF)4 Slew rate control disabled (PTxSE = 0) Slew rate control enabled (PTxSE = 1) high output drive (PTxDS = 1), (load = 50 pF) Slew rate control disabled (PTxSE = 0) Slew rate control enabled (PTxSE = 1) Typical values are based on characterization data at VDD = 5.0 V, 25 °C unless otherwise stated. This is the shortest pulse that is guaranteed to be recognized as a reset pin request. Shorter pulses are not guaranteed to override reset requests from internal sources. 3 This is the minimum pulse width that is guaranteed to pass through the pin synchronization circuitry. Shorter pulses may or may not be recognized. In stop mode, the synchronizer is bypassed so shorter pulses can be recognized in that case. 4 Timing is shown with respect to 20% V DD and 80% VDD levels. Temperature range –40 °C to 85 °C. 1 2 MC9S08JM60 Series Data Sheet, Rev. 3 364 Freescale Semiconductor Appendix A Electrical Characteristics textrst RESET PIN Figure A-6. Reset Timing tIHIL IRQ/KBIPx IRQ/KBIPx tILIH Figure A-7. IRQ/KBIPx Timing A.12.2 Timer/PWM (TPM) Module Timing Synchronizer circuits determine the shortest input pulses that can be recognized or the fastest clock that can be used as the optional external source to the timer counter. These synchronizers operate from the current bus rate clock. Table A-14. TPM Input Timing NUM 1 2 3 4 5 C — — D D D Function External clock frequency External clock period External clock high time External clock low time Input capture pulse width tTPMext tclkh Symbol fTPMext tTPMext tclkh tclkl tICPW Min dc 4 1.5 1.5 1.5 Max fBus/4 — — — — Unit MHz tcyc tcyc tcyc tcyc TPMxCLK tclkl Figure A-8. Timer External Clock MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 365 Appendix A Electrical Characteristics tICPW TPMxCHn TPMxCHn tICPW Figure A-9. Timer Input Capture Pulse A.12.3 SPI Characteristics Table A-15. SPI Electrical Characteristic Num1 1 C D Cycle time 2 D Enable lead time 3 D Enable lag time 4 D Master Slave Clock (SPSCK) high time Master and Slave Clock (SPSCK) low time Master and Slave Data setup time (inputs) 7 D Data hold time (inputs) 8 9 10 11 D D D D Data hold time (outputs) 12 D Master Slave tHO tHO –10 –10 — — ns ns Access time, slave3 Disable time, slave 4 Table A-15 and Figure A-10 through Figure A-13 describe the timing requirements for the SPI system. Characteristic2 Operating frequency Master Slave Master Slave Master Slave fop fop tSCK tSCK tLead tLead tLag tLag tSCKH tSCKL tSI(M) tSI(S) tHI(M) tHI(S) tA tdis Master Slave tSO tSO fBus/2048 dc 2 4 — 1/2 — 1/2 1/2 tSCK – 25 1/2 tSCK – 25 30 30 30 30 0 — 25 25 fBus/2 fBus/4 2048 — 1/2 — 1/2 — — — — — — — 40 40 — — Hz Symbol Min Max Unit tcyc tcyc tSCK tSCK tSCK tSCK ns ns ns ns ns ns ns ns ns ns 5 6 D D Master Slave Master Slave Data setup time (outputs) MC9S08JM60 Series Data Sheet, Rev. 3 366 Freescale Semiconductor Appendix A Electrical Characteristics 1 2 Refer to Figure A-10 through Figure A-13. All timing is shown with respect to 20% VDD and 70% VDD, unless noted; 100 pF load on all SPI pins. All timing assumes slew rate control disabled and high drive strength enabled for SPI output pins. 3 Time to data active from high-impedance state. 4 Hold time to high-impedance state. SS1 (OUTPUT) 2 SCK (CPOL = 0) (OUTPUT) SCK (CPOL = 1) (OUTPUT) 6 MISO (INPUT) MSB IN2 10 MOSI (OUTPUT) MSB OUT2 7 BIT 6 . . . 1 10 BIT 6 . . . 1 LSB OUT LSB IN 11 1 5 4 3 5 4 NOTES: 1. SS output mode (MODFEN = 1, SSOE = 1). 2. LSBF = 0. For LSBF = 1, bit order is LSB, bit 1, ..., bit 6, MSB. Figure A-10. SPI Master Timing (CPHA = 0) MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 367 Appendix A Electrical Characteristics SS(1) (OUTPUT) 1 2 SCK (CPOL = 0) (OUTPUT) SCK (CPOL = 1) (OUTPUT) MISO (INPUT) 10 MOSI (OUTPUT) MSB OUT(2) 5 4 5 4 6 7 MSB IN(2) BIT 6 . . . 1 11 BIT 6 . . . 1 LSB OUT LSB IN 3 NOTES: 1. SS output mode (MODFEN = 1, SSOE = 1). 2. LSBF = 0. For LSBF = 1, bit order is LSB, bit 1, ..., bit 6, MSB. Figure A-11. SPI Master Timing (CPHA = 1) SS (INPUT) 1 SCK (CPOL = 0) (INPUT) 2 SCK (CPOL = 1) (INPUT) 8 MISO (OUTPUT) SLAVE 6 MOSI (INPUT) NOTE: 3 5 4 5 4 10 MSB OUT 7 MSB IN BIT 6 . . . 1 LSB IN BIT 6 . . . 1 11 SLAVE LSB OUT SEE NOTE 9 1. Not defined but normally MSB of character just received Figure A-12. SPI Slave Timing (CPHA = 0) MC9S08JM60 Series Data Sheet, Rev. 3 368 Freescale Semiconductor Appendix A Electrical Characteristics SS (INPUT) 1 2 SCK (CPOL = 0) (INPUT) SCK (CPOL = 1) (INPUT) MISO (OUTPUT) SEE NOTE 8 MOSI (INPUT) 5 4 5 4 10 SLAVE 6 MSB IN MSB OUT 7 BIT 6 . . . 1 LSB IN 11 BIT 6 . . . 1 SLAVE LSB OUT 9 3 NOTE: 1. Not defined but normally LSB of character just received Figure A-13. SPI Slave Timing (CPHA = 1) A.13 Flash Specifications This section provides details about program/erase times and program-erase endurance for the flash memory. Program and erase operations do not require any special power sources other than the normal VDD supply. For more detailed information about program/erase operations. Table A-16. Flash Characteristics Num 1 2 3 4 5 6 7 8 9 C C Characteristic Supply voltage for program/erase Supply voltage for read operation Internal FCLK frequency2 Internal FCLK period (1/FCLK) Byte program time (random location)(2) Byte program time (burst mode)(2) Page erase time3 Mass erase time (2) Symbol Vprog/erase VRead fFCLK tFcyc tprog tBurst tPage tMass Min 2.7 2.7 150 5 Typ1 Max 5.5 5.5 200 6.67 Unit V V kHz μs tFcyc tFcyc tFcyc tFcyc 9 4 4000 20,000 10,000 — — 100,000 100 — — — Program/erase endurance4 TL to TH = –40°C to + 85°C T = 25°C Data retention5 tD_ret cycles years 10 1 15 Typical values are based on characterization data at VDD = 5.0 V, 25°C unless otherwise stated. MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 369 Appendix A Electrical Characteristics 2 3 The frequency of this clock is controlled by a software setting. These values are hardware state machine controlled. User code does not need to count cycles. This information supplied for calculating approximate time to program and erase. 4 Typical endurance for Flash is based on the intrinsic bitcell performance. For additional information on how Freescale Semiconductor defines typical endurance, please refer to Engineering Bulletin EB619/D, Typical Endurance for Nonvolatile Memory. 5 Typical data retention values are based on intrinsic capability of the technology measured at high temperature and de-rated to 25 °C using the Arrhenius equation. For additional information on how Freescale Semiconductor defines typical data retention, please refer to Engineering Bulletin EB618/D, Typical Data Retention for Nonvolatile Memory. A.14 USB Electricals The USB electricals for the S08USBV1 module conform to the standards documented by the Universal Serial Bus Implementers Forum. For the most up-to-date standards, visit http://www.usb.org. If the Freescale S08USBV1 implementation has electrical characteristics that deviate from the standard or require additional information, this space would be used to communicate that information. Table A-17. Internal USB 3.3V Voltage Regulator Characteristics Symbol Regulator operating voltage VREG output VUSB33 input with internal VREG disabled VREG Quiescent Current Vregin Vregout Vusb33in IVRQ Unit V V V mA Min 3.9 3 3 — Typ — 3.3 3.3 0.5 Max 5.5 3.6 3.6 — A.15 EMC Performance Electromagnetic compatibility (EMC) performance is highly dependant on the environment in which the MCU resides. Board design and layout, circuit topology choices, location and characteristics of external components as well as MCU software operation all play a significant role in EMC performance. The system designer must consult Freescale applications notes such as AN2321, AN1050, AN1263, AN2764, and AN1259 for advice and guidance specifically targeted at optimizing EMC performance. A.15.1 Radiated Emissions Microcontroller radiated RF emissions are measured from 150 kHz to 1 GHz using the TEM/GTEM Cell method in accordance with the IEC 61967-2 and SAE J1752/3 standards. The measurement is performed with the microcontroller installed on a custom EMC evaluation board while running specialized EMC test software. The radiated emissions from the microcontroller are measured in a TEM cell in two package orientations (North and East). For more detailed information concerning the evaluation results, conditions and setup, please refer to the EMC Evaluation Report for this device. The maximum radiated RF emissions of the tested configuration in all orientations are less than or equal to the reported emissions levels. MC9S08JM60 Series Data Sheet, Rev. 3 370 Freescale Semiconductor Appendix A Electrical Characteristics Table A-18. Radiated Emissions Parameter Symbol Conditions Frequency 0.15 – 50 MHz 50 – 150 MHz Radiated emissions, electric field VRE_TEM VDD = 5.0 V TA = +25oC 150 – 500 MHz 500 – 1000 MHz IEC Level SAE Level 1 fOSC/fBUS Level1 (Max) 20 27 Unit dBμV 4 MHz crystal 24 MHz Bus 27 16 1 3 — — Data based on qualification test results. MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 371 Appendix A Electrical Characteristics MC9S08JM60 Series Data Sheet, Rev. 3 372 Freescale Semiconductor Appendix B Ordering Information and Mechanical Drawings B.1 Ordering Information This section contains ordering numbers for MC9S08JM60 series devices. See below for an example of the device numbering system. Table B-1. Device Numbering System Device Number1 Flash MC9S08JM60 MC9S08JM32 1 2 Memory RAM 4096 2048 Available Packages2 Type 64-pin LQFP 64-pin QFP 48-pin QFN 44-pin LQFP 60,912 32,768 See Table 1-1 for a complete description of modules included on each device. See Table B-2 for package information. B.2 Orderable Part Numbering System MC 9 S08 JM 60 C XX E Status (MC = Fully Qualified) Memory (9 = Flash-based) Core Family Pb free indicator Package designator (See Table B-2) Temperature range (C = –40°C to 85°C) Memory size designator B.3 Mechanical Drawings This following pages contain mechanical specifications for MC9S08JM60 series package options. See Table B-2 for the document numbers that correspond to each package type. Table B-2. Package Information Pin Count 44 48 64 64 Type LQFP QFN LQFP QFP Designator LD GT LH QH Document No. 98ASS23225W 98ARH99048A 98ASS23234W 98ASB42844B MC9S08JM60 Series Data Sheet, Rev. 3 Freescale Semiconductor 373 How to Reach Us: Home Page: www.freescale.com Web Support: http://www.freescale.com/support USA/Europe or Locations Not Listed: Freescale Semiconductor, Inc. Technical Information Center, EL516 2100 East Elliot Road Tempe, Arizona 85284 1-800-521-6274 or +1-480-768-2130 www.freescale.com/support Europe, Middle East, and Africa: Freescale Halbleiter Deutschland GmbH Technical Information Center Schatzbogen 7 81829 Muenchen, Germany +44 1296 380 456 (English) +46 8 52200080 (English) +49 89 92103 559 (German) +33 1 69 35 48 48 (French) www.freescale.com/support Japan: Freescale Semiconductor Japan Ltd. Headquarters ARCO Tower 15F 1-8-1, Shimo-Meguro, Meguro-ku, Tokyo 153-0064 Japan 0120 191014 or +81 3 5437 9125 support.japan@freescale.com Asia/Pacific: Freescale Semiconductor China Ltd. Exchange Building 23F No. 118 Jianguo Road Chaoyang District Beijing 100022 China +86 10 5879 8000 support.asia@freescale.com For Literature Requests Only: Freescale Semiconductor Literature Distribution Center P.O. Box 5405 Denver, Colorado 80217 1-800-441-2447 or +1-303-675-2140 Fax: +1-303-675-2150 LDCForFreescaleSemiconductor@hibbertgroup.com Information in this document is provided solely to enable system and software implementers to use Freescale Semiconductor products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document. Freescale Semiconductor reserves the right to make changes without further notice to any products herein. Freescale Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters that may be provided in Freescale Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”, must be validated for each customer application by customer’s technical experts. Freescale Semiconductor does not convey any license under its patent rights nor the rights of others. Freescale Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Freescale Semiconductor product could create a situation where personal injury or death may occur. Should Buyer purchase or use Freescale Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Freescale Semiconductor was negligent regarding the design or manufacture of the part. RoHS-compliant and/or Pb-free versions of Freescale products have the functionality and electrical characteristics as their non-RoHS-compliant and/or non-Pb-free counterparts. For further information, see http://www.freescale.com or contact your Freescale sales representative. For information on Freescale’s Environmental Products program, go to http://www.freescale.com/epp. Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. © Freescale Semiconductor, Inc. 2007-2009. All rights reserved. M C9S08JM60 Rev. 3, 1/2009