MPC7410TRX400NE

Freescale Semiconductor Technical Data Document Number: MPC7410ECS07AD Rev. 2, 11/2010 MPC7410 RISC Microprocessor Hardware Specifications Addendum for the MPC7410TxxnnnNE Series This document describes part-number-specific changes to the MPC7410 RISC Microprocessor Hardware Specifications (Document No. MPC7410EC). Specifications provided in this document supersede those in the MPC7410 RISC Microprocessor Hardware Specifications, Rev. 6.1 or later, for the part numbers listed in Table A. only. Specifications not addressed herein are unchanged. Because this document is frequently updated, see the website listed on the back page of this document or contact your Freescale sales office for the latest version. Freescale Part Numbers Affected: MPC7410TRX400NE MPC7410TRX450NE MPC7410THX450NE © 2010 Freescale Semiconductor, Inc. All rights reserved. Table A. Part-Number-Specific Changes Operating Conditions Freescale Part Number CPU Frequency 400 MHz Vdd 1.5V±50mV TJ (°C) -40 to 105 OVdd 1.8/2.5 V Significant Differences from Hardware Specification MPC7410TRX400NE Extended temperature range. Reduced core voltage to achieve lower power consumption. Removes 3.3 V OVdd support. For all AC/DC specifications not mentioned in this document, see the MPC7410RX400LE specifications in the general MPC7410 Hardware Specifications. 450 MHz 1.8V±100mV -40 to 105 1.8/2.5/3.3 V Extended temperature range. The MPC7410TRX400NE also fully conforms to the MPC7410TRX450LE specification. See the general MPC7410 Hardware Specifications. 1.5V±50mV -40 to 105 1.8/2.5 V Extended temperature range. Reduced core voltage to achieve lower power consumption. Removes 3.3V OVdd support. For all AC/DC specifications not mentioned in this document, please refer to the MPC7410RX450LE specifications in the general MPC7410 Hardware Specifications. MPC7410TRX450NE 450 MHz 500 MHz 1.8V±100mV -40 to 105 1.8/2.5/3.3 V Extended temperature range. The MPC7410TRX450NE also fully conforms to the MPC7410TRX500LE specification. See the general MPC7410 Hardware Specifications. 1.5V±50mV -40 to 105 1.8/2.5 V Extended temperature range. Reduced core voltage to achieve lower power consumption. Removes 3.3V OVdd support. For all AC/DC specifications not mentioned in this document, see to the MPC7410HX450LE specifications in the general MPC7410 Hardware Specifications. MPC7410THX450NE 450 MHz 500 MHz 1.8V±100mV -40 to 105 1.8/2.5/3.3 V Extended temperature range. The MPC7410THX450NE also fully conforms to the MPC7410THX500LE specification. See the general MPC7410 Hardware Specifications. Features The MPC7410TxxnnnNE feature set is identical to that of the MPC7410, with the following exceptions: • Bus interface — Selectable interface voltages of 1.8 V, 2.5 V (3.3 V is not supported) DC Electrical Characteristics The MPC7410TxxnnnNE DC electrical characteristics are identical to that of the MPC7410, with the exceptions shown in Table B, Table C, and Table D. MPC7410 RISC Microprocessor Hardware Specifications Addendum for the MPC7410TxxnnnNE Series, Rev. 2 2 Freescale Semiconductor Voltage to the L2 I/Os and processor interface I/Os are provided through separate sets of supply pins and may be provided at the voltages shown in Table B. Table B. Input Threshold Voltage Setting BVSEL Signal 3 0 HRESET 1 HRESET Processor Bus Input Threshold is Relative to: 1.8 V 2.5 V Not Supported Not Supported L2VSEL Signal 3 0 HRESET 1 HRESET L2 Bus Input Threshold is Relative to: 1.8 V 2.5 V 2.5 V Not Supported Note 1 1, 2 1, 4, 5 — Notes: 1. Caution: The input threshold selection must agree with the OVdd/L2OVdd voltages supplied. 2. To select the 2.5-V threshold option, BVSEL and/or L2VSEL should be tied to HRESET so that the two signals change state together. This is the preferred method for selecting this mode of operation. 3. To overcome the internal pull-up resistance, a pull-down resistance less than 250 ohms should be used. 4. Default voltage setting if left unconnected (internal pulled-up). 5. Caution: The MPC7410TRXnnnNE does not support the default OVdd setting of 3.3 V. The BVSEL input must be tie either low or to HRESET. Table C. Recommended Operating Conditions Characteristic Core supply voltage PLL supply voltage L2 DLL supply voltage Processor bus supply voltage BVSEL = 0 BVSEL = HRESET BVSEL = HRESET or BVSEL = 1 L2 bus supply voltage L2VSEL = 0 L2VSEL = HRESET or L2VSEL = 1 Input voltage Processor bus and JTAG Signals L2 Bus Die-junction temperature Symbol Vdd AVdd L2AVdd OVdd OVdd OVdd L2OVdd L2OVdd Vin Vin Tj Recommended Value 1.5V ± 50mV 1.5V ± 50mV 1.5V ± 50mV 1.8V ± 100mV 2.5V ± 100mV Not Supported 1.8V ± 100mV 2.5V ± 100mV GND to OVdd GND to L2OVdd -40 to 105 Unit V V V V V V V V V V °C MPC7410 RISC Microprocessor Hardware Specifications Addendum for the MPC7410TxxnnnNE Series, Rev. 2 Freescale Semiconductor 3 Table D. Power Consumption for MPC7410 Processor (CPU) Frequency 400 MHz Full-On Mode Typical Maximum Doze Mode Maximum Nap Mode Maximum Sleep Mode Maximum Sleep Mode—PLL and DLL Disabled Typical Maximum 0.6 1.1 0.6 1.1 W W 1, 3 1, 2 1.3 1.45 W 1, 2 1.35 1.5 W 1, 2 3.6 4.1 W 1, 2 2.92 6.6 3.29 7.43 W W 1, 3 1, 2, Processor (CPU) Frequency 450 MHz Unit Notes Notes: 1. These values apply for all valid processor bus and L2 bus ratios. The values do not include I/O Supply Power (OVdd and L2OVdd) or PLL/DLL supply power (AVdd and L2AVdd). OVdd and L2OVdd power is system dependent, but is typically