0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
创作中心
发布
  • 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
MPC8308_101

MPC8308_101

  • 厂商:

    FREESCALE(飞思卡尔)

  • 封装:

  • 描述:

    MPC8308_101 - MPC8308 PowerQUICC II Pro Processor Hardware Specification - Freescale Semiconductor, ...

  • 数据手册
  • 价格&库存
MPC8308_101 数据手册
Freescale Semiconductor Document Number: MPC8308EC Rev. 1, 07/2010 MPC8308 PowerQUICC II Pro Processor Hardware Specification This document provides an overview of the MPC8308 features and its hardware specifications, including a block diagram showing the major functional components. The MPC8308 is a cost-effective, low-power, highly integrated host processor. The MPC8308 extends the PowerQUICC family, adding higher CPU performance, additional functionality, and faster interfaces while addressing the requirements related to time-to-market, price, power consumption, and package size. NOTE The information provided in this document is preliminary and is based on estimates only and refers to the pre-silicon phase, with no device characterization done. Freescale reserves the right to change the contents of this document as appropriate. 1 Overview Figure 1 shows the major functional units within the MPC8308. The e300 core in the MPC8308, with its 16 Kbytes of instruction and 16 Kbytes of data cache, implements the Power Architecture user instruction set architecture and provides hardware and software debugging 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. Contents Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . 2 Power Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . 6 Clock Input Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 RESET Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . 8 DDR2 SDRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 DUART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Ethernet: Three-Speed Ethernet, MII Management . 15 USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 High-Speed Serial Interfaces (HSSI) . . . . . . . . . . . . 24 PCI Express . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Enhanced Local Bus . . . . . . . . . . . . . . . . . . . . . . . . . 43 Enhanced Secure Digital Host Controller (eSDHC) . 47 JTAG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 I2C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Timers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 GPIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 IPIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 SPI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Package and Pin Listings . . . . . . . . . . . . . . . . . . . . . 62 Clocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 Thermal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 System Design Information . . . . . . . . . . . . . . . . . . . 81 Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . 85 Document Revision History . . . . . . . . . . . . . . . . . . . 86 © Freescale Semiconductor, Inc., 2010. All rights reserved. Electrical Characteristics support. In addition, the MPC8308 offers a PCI Express controller, two three-speed 10, 100, 1000 Mbps Ethernet controllers (eTSEC), a DDR2 SDRAM memory controller, a SerDes block, an enhanced local bus controller (eLBC), an integrated programmable interrupt controller (IPIC), a general purpose DMA controller, two I2C controllers, dual UART (DUART), GPIOs, USB, general purpose timers, and an SPI controller. The high level of integration in the MPC8308 helps simplify board design and offers significant bandwidth and performance. A block diagram of the device is shown in Figure 1. e300c3 Core with Power Management DUART I2C Timers GPIO, SPI 16-Kbyte I-Cache Interrupt Controller FPU 16-Kbyte D-Cache DMA Enhanced Local Bus DDR2 Controller Enhanced Secure Digital Host Controller PCI Express x1 USB 2.0 HS Host/Device/OTG ULPI eTSEC1 RGMII,MII eTSEC2 RGMII,MII Figure 1. MPC8308 Block Diagram 2 Electrical Characteristics This section provides the AC and DC electrical specifications and thermal characteristics for the MPC8308. The device is currently targeted to these specifications. Some of these specifications are independent of the I/O cell, but are included for a more complete reference. These are not purely I/O buffer design specifications. 2.1 Overall DC Electrical Characteristics This section covers the ratings, conditions, and other characteristics. 2.1.1 Absolute Maximum Ratings Table 1. Absolute Maximum Ratings1 Characteristic Symbol VDD AVDD1, AVDD2 GVDD Max Value –0.3 to 1.26 –0.3 to 1.26 –0.3 to 1.9 Unit V V V Notes — — — Table 1 provides the absolute maximum ratings. Core supply voltage PLL supply voltage DDR2 DRAM I/O voltage M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 2 Freescale Semiconductor Electrical Characteristics Table 1. Absolute Maximum Ratings1 (continued) Characteristic Local bus, DUART, system control and power management, eSDHC, I2C, USB, Interrupt, Ethernet management, SPI, Miscellaneous and JTAG I/O voltage SERDES PHY Symbol NVDD Max Value –0.3 to 3.6 Unit V Notes 7 XCOREVDD, XPADVDD, SDAV DD LVDD1, LVDD2 MVIN MVREF LV IN OVIN –0.3 to 1.26 V — eTSEC I/O Voltage Input voltage DDR2 DRAM signals DDR2 DRAM reference eTSEC Local bus, DUART, system control and power management, eSDHC, I2C, Interrupt, Ethernet management, SPI, Miscellaneous and JTAG I/O voltage Storage temperature range –0.3 to 2.75 or –0.3 to 3.6 –0.3 to (GVDD + 0.3) –0.3 to (GVDD + 0.3) –0.3 to (LVDD + 0.3) –0.3 to (NVDD + 0.3) V V V V V 6,8 2, 5 2, 5 4, 5,8 3, 5,7 TSTG –55 to 150 °C — Notes: 1. Functional and tested operating conditions are given in Table 2. Absolute maximum ratings are stress ratings only, and functional operation at the maximums is not guaranteed. Stresses beyond those listed may affect device reliability or cause permanent damage to the device. 2. Caution: MVIN must not exceed GVDD by more than 0.3 V. This limit may be exceeded for a maximum of 20 ms during power-on reset and power-down sequences. 3. Caution: OVIN must not exceed NVDD by more than 0.3 V. This limit may be exceeded for a maximum of 20 ms during power-on reset and power-down sequences. 4. Caution: LV IN must not exceed LVDD by more than 0.3 V. This limit may be exceeded for a maximum of 20 ms during power-on reset and power-down sequences. 5. (M, L, O)VIN and MV REF may overshoot/undershoot to a voltage and for a maximum duration as shown in Figure 2 6. The max value of supply voltage should be selected based on the RGMII mode. The lower range applies to RGMII mode. 7. NVDD here refers to NVDDA, NVDDB,NVDDG, NVDDH, NVDDP_K from the ball map. 8. LVDD1 here refers to NVDDC and LVDD2 refers to NVDDF from the ball map 2.1.2 Power Supply Voltage Specification Table 2 provides the recommended operating conditions for the device. Note that the values in Table 2 are the recommended and tested operating conditions. Proper device operation outside of these conditions is not guaranteed. Table 2. Recommended Operating Conditions Characteristic SerDes internal digital power SerDes internal digital power SerDes I/O digital power SerDes analog power for PLL Symbol XCOREV DD XCOREVSS XPADVDD SDAVDD Recommended Value1 1.0 V ± 50 mV 0.0 1.0 V ± 50 mV 1.0 V ± 50 mV Unit V V V V M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 Freescale Semiconductor 3 Electrical Characteristics Table 2. Recommended Operating Conditions (continued) Characteristic SerDes analog power for PLL SerDes I/O digital power Core supply voltage Analog supply for e300 core APLL Analog supply for system APLL DDR2 DRAM I/O voltage Differential reference voltage for DDR controller Standard I/O voltage (Local bus, DUART, system control and power management, eSDHC, USB, I2C, Interrupt, Ethernet management, SPI, Miscellaneous and JTAG I/O voltage)2 eTSEC IO supply3,4 Analog and digital ground Junction temperature5 Notes: 1 2 3 4 5 Symbol SDAVSS XPADVSS VDD AVDD1 AVDD2 GV DD MVREF NVDD Recommended Value1 0 0 1.0 V ± 50 mV 1.0 V ± 50 mV 1.0 V ± 50 mV 1.8 V ± 100 mV GVDD/2 (0.49 × GVDD to 0.51 × GVDD) 3.3 V ± 300 mV Unit V V V V V V V V LVDD1, LVDD2 VSS TA/TJ 2.5 V ± 125 mV 3.3 V ± 300 mV 0.0 0 to 105 V V °C GVDD, NVDD, AVDD, and VDD must track each other and must vary in the same direction—either in the positive or negative direction. NVDD here refers to NVDDA, NVDDB,NV DDG, NVDDH and NVDDP_K from the ball map. The max value of supply voltage should be selected based on the RGMII mode. The lower range applies to RGMII mode. LVDD1 here refers to NVDDC and LVDD2 refers to NVDDF from the ball map. Minimum temperature is specified with TA; Maximum temperature is specified with TJ. M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 4 Freescale Semiconductor Electrical Characteristics Figure 2 shows the undershoot and overshoot voltages at the interfaces of the device G/L/NVDD + 20% G/L/NVDD + 5% VIH G/L/NVDD VSS VSS – 0.3 V VIL VSS – 0.7 V Not to Exceed 10% of tinterface1 Note: 1. Note that tinterface refers to the clock period associated with the bus clock interface. Figure 2. Overshoot/Undershoot Voltage for GVDD/NVDD/LVDD 2.1.3 Output Driver Characteristics Table 3. Output Driver Capability Driver Type Output Impedance (Ω ) 42 18 42 42 Supply Voltage NVDD = 3.3 V GVDD = 1.8 V NVDD = 3.3 V LVDD = 2.5/3.3 V Table 3 provides information on the characteristics of the output driver strengths. Local bus interface utilities signals DDR2 signals1 DUART, system control, I2C, JTAG, eSDHC, GPIO,SPI, USB eTSEC signals 1 Output Impedance can also be adjusted through configurable options in DDR Control Driver Register (DDRCDR). For more information, see the MPC8308 PowerQUICC II Pro Processor Reference Manual. 2.1.4 Power Sequencing The device does not require the core supply voltage (VDD) and I/O supply voltages (GVDD, LVDD, and NVDD) to be applied in any particular order. Note that during power ramp-up, before the power supplies are stable and if the I/O voltages are supplied before the core voltage, there might be a period of time that all input and output pins are actively driven and cause contention and excessive current. In order to avoid actively driving the I/O pins and to eliminate excessive current draw, apply the core voltage (VDD) before the I/O voltage (GVDD, LVDD, and NVDD) and assert PORESET before the power supplies fully ramp up. In the case where the core voltage is applied first, the core voltage supply must rise to 90% of its nominal value before the I/O supplies reach 0.7 V; see Figure 3. M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 Freescale Semiconductor 5 Power Characteristics The I/O power supply ramp-up slew rate should be slower than 4V/100 μs; this requirement is for ESD circuit. Note that there is no specific power-down sequence requirement for the device. I/O voltage supplies (GVDD, LVDD, and NVDD) do not have any ordering requirements with respect to one another. V I/O Voltage (GVDD, LVDD, and NVDD ) Core Voltage (VDD) 90% 0.7 V 0 PORESET >= 32 × tSYS_CLK_IN t Figure 3. Power-Up Sequencing Example 3 Power Characteristics The estimated typical power dissipation, not including I/O supply power for the device is shown in Table 4. Table 5 shows the estimated typical I/O power dissipation. Table 4. MPC8308 Power Dissipation1 Core Frequency (MHz) 266 333 400 Notes: The values do not include I/O supply power but do include core (AVDD) and PLL (AVDD1, AVDD2, XCOREV DD, XPADVDD, SDAVDD) 2 Typical power is based on best process, a voltage of VDD = 1.0V and ambient temperature of TA = 25° C 3 Maximum power is estimated based on best process, a voltage of VDD = 1.05 V and ambient temperature of TJ = 105° C 1 CSB Frequency (MHz) 133 133 133 Typical2 530 565 600 Maximum3 900 950 1000 Unit mW mW mW M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 6 Freescale Semiconductor Clock Input Timing Table 5 describes a typical scenario where blocks with the stated percentage of utilization and impedances consume the amount of power described. 1 Table 5. MPC8308 Typical I/O Power Dissipation Interface DDR2 Rs = 2 2 Ω Rt = 75 Ω Local bus I/O load = 20 pF TSE C I/O load = 20 pF Parameter 250 MHz 32 bits+ECC 266 MHz 32 bits+ECC 62.5 MHz 66 MHZ MII, 25 MHz RGMII, 125 MHz eSDHC IO Load = 40 pF USB IO Load = 20 pF Other I/O 50 MHz 60 MHz — GV DD (1.8 V) 0.302 0.309 — — — — — — 0.038 0.040 — — — — 0.017 — 0.008 0.078 0.008 0.012 — — — — 0.044 — W W W W W W — — — — 2 controllers NVDD (3.3 V) — LVDD (3.3 V) — LVDD (2.5 V) — Unit W Comments — 4 4.1 Clock Input Timing DC Electrical Characteristics Table 6. SYS_CLK_IN DC Electrical Characteristics Parameter Input high voltage Input low voltage SYS_CLK_IN input current Condition — — 0 V ≤ VIN ≤ NVDD Symbol VIH VIL IIN Min 2.4 –0.3 — Max NVDD + 0.3 0.4 ±10 Unit V V μA This section provides the clock input DC and AC electrical characteristics for the device. Table 6 provides the system clock input (SYS_CLK_IN) DC electrical specifications for the device. Table 7 provides the RTC clock input (RTC_PIT_CLOCK) DC electrical specifications for the device. Table 7. RTC_PIT_CLOCK DC Electrical Characteristics Parameter Input high voltage Input low voltage Condition — — Symbol VIH VIL Min 3.3V – 400 mV 0 0.4 Max Unit V V M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 Freescale Semiconductor 7 RESET Initialization 4.2 AC Electrical Characteristics The primary clock source for the device is SYS_CLK_IN. Table 8 provides the system clock input (SYS_CLK_IN) AC timing specifications for the device. Table 8. SYS_CLK_IN AC Timing Specifications Parameter SYS_CLK_IN frequency SYS_CLK_IN period SYS_CLK_IN rise and fall time SYS_CLK_IN duty cycle SYS_CLK_IN Jitter Symbol fSYS_CLK_IN tSYS_CLK_IN tKH, tKL tKHK/tSYS_CLK_IN — Min 24 15 0.6 40 — — — Typ — — Max 66.67 41.67 1.2 60 ±150 Unit MHz ns ns % ps Notes 1, 6 — 2 3 4, 5 Notes: 1. Caution: The system and core must not exceed their respective maximum or minimum operating frequencies. 2. Rise and fall times for SYS_CLK_IN are measured at 0.4 and 2.7 V. 3. Timing is guaranteed by design and characterization. 4. This represents the total input jitter—short term and long term—and is guaranteed by design. 5. The SYS_CLK_IN driver’s closed loop jitter bandwidth should be 1,000,000 16 Unit baud baud — Notes — 1 2 Table 20 provides the AC timing parameters for the DUART interface. Notes: 1. Actual attainable baud rate is limited by the latency of interrupt processing. 2. The middle of a start bit is detected as the 8th sampled 0 after the 1-to-0 transition of the start bit. Subsequent bit values are sampled each 16th sample. 8 Ethernet: Three-Speed Ethernet, MII Management This section provides the AC and DC electrical characteristics for three-speed, 10/100/1000, and MII management. MPC8308 supports dual Ethernet controllers. 8.1 Enhanced Three-Speed Ethernet Controller (eTSEC) (10/100/1000 Mbps)—MII/RGMII Electrical Characteristics The electrical characteristics specified here apply to all the media independent interface (MII) and reduced gigabit media independent interface (RGMII) signals except management data input/output (MDIO) and management data clock (MDC). The RGMII interface is defined for 2.5 V, while the MII interface can be operated at 3.3 V. The RGMII interface follows the Hewlett-Packard reduced pin-count interface for Gigabit Ethernet Physical Layer Device Specification Version 1.2a (9/22/2000). The electrical characteristics for MDIO and MDC are specified in Section 8.3, “Ethernet Management Interface Electrical Characteristics.” M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 Freescale Semiconductor 15 Ethernet: Three-Speed Ethernet, MII Management 8.1.1 eTSEC DC Electrical Characteristics All MII and RGMII drivers and receivers comply with the DC parametric attributes specified in Table 21 and Table 22. The RGMII signals are based on a 2.5-V CMOS interface voltage as defined by JEDEC EIA/JESD8-5. Table 21. MII DC Electrical Characteristics Parameter Supply voltage 3.3 V Output high voltage Output low voltage Input high voltage Input low voltage Input high current Input low current Symbol LVDD VOH VOL VIH VIL IIH IIL IOH = –4.0 mA IOL = 4.0 mA — — VIN 1 = LVDD VIN 1= Conditions — LVDD = M in LVDD= Min — — Min 3.0 2.40 VSS 2.1 –0.3 — –600 Max 3.6 LVDD + 0.3 0.50 LVDD + 0.3 0.90 40 — Unit V V V V V μA μA VSS Note: 1. The symbol VIN, in this case, represents the LVIN symbol referenced in Table 1 and Table 2. Table 22. RGMII DC Electrical Characteristics Parameters Supply voltage 2.5 V Output high voltage Output low voltage Input high voltage Input low voltage Input high current Input low current Symbol LVDD VOH VOL VIH VIL IIH IIL IOH = –1.0 mA IOL = 1.0 mA — — Conditions — LVDD = Min LVDD= Min LVDD = Min LVDD = Min VIN 1 = LVDD VIN 1 = VSS Min 2.37 2.00 VSS – 0.3 1.7 –0.3 — –15 Max 2.63 LVDD + 0.3 0.40 LVDD + 0.3 0.70 15 — Unit V V V V V μA μA Note: 1. Note that the symbol VIN, in this case, represents the LVIN symbol referenced in Table 1 and Table 2. 8.2 MII and RGMII AC Timing Specifications The AC timing specifications for MII and RGMII are presented in this section. 8.2.1 MII AC Timing Specifications This section describes the MII transmit and receive AC timing specifications. M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 16 Freescale Semiconductor Ethernet: Three-Speed Ethernet, MII Management 8.2.1.1 MII Transmit AC Timing Specifications Table 23. MII Transmit AC Timing Specifications Table 23 provides the MII transmit AC timing specifications. At recommended operating conditions with LVDDA/LVDDB /NVDD of 3.3 V ± 0.3V. Parameter/Condition TX_CLK clock period 10 Mbps TX_CLK clock period 100 Mbps TX_CLK duty cycle TX_CLK to MII data TXD[3:0], TX_ER, TX_EN delay TX_CLK data clock rise VIL(min) to VIH(max) TX_CLK data clock fall VIH(max) to VIL(min) Symbol 1 tMTX tMTX tMTXH/tMTX tMTKHDX tMTXR tMTXF Min — — 35 1 1.0 1.0 Typ 400 40 — 5 — — Max — — 65 15 4.0 4.0 Unit ns ns % ns ns ns Note: 1. The symbols used for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tMTKHDX symbolizes MII transmit timing (MT) for the time tMTX clock reference (K) going high (H) until data outputs (D) are invalid (X). Note that, in general, the clock reference symbol representation is based on two to three letters representing the clock of a particular functional. For example, the subscript of tMTX represents the MII(M) transmit (TX) clock. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall). Figure 8 shows the MII transmit AC timing diagram. tMTX TX_CLK tMTXH TXD[3:0] TX_EN TX_ER tMTKHDX tMTXF tMTXR Figure 8. MII Transmit AC Timing Diagram 8.2.1.2 MII Receive AC Timing Specifications Table 24. MII Receive AC Timing Specifications Table 24 provides the MII receive AC timing specifications. At recommended operating conditions with LVDD /NVDD of 3.3 V ± 0.3V. Parameter/Condition RX_CLK clock period 10 Mbps RX_CLK clock period 100 Mbps RX_CLK duty cycle RXD[3:0], RX_DV, RX_ER setup time to RX_CLK Symbol 1 tMRX tMRX tMRXH/tMRX tMRDVKH Min — — 35 10.0 Typ 400 40 — — Max — — 65 — Unit ns ns % ns M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 Freescale Semiconductor 17 Ethernet: Three-Speed Ethernet, MII Management Table 24. MII Receive AC Timing Specifications (continued) At recommended operating conditions with LVDD /NVDD of 3.3 V ± 0.3V. Parameter/Condition RXD[3:0], RX_DV, RX_ER hold time to RX_CLK RX_CLK clock rise VIL(min) to VIH(max) RX_CLK clock fall time VIH(max) to VIL(min) Symbol 1 tMRDXKH tMRXR tMRXF Min 10.0 1.0 1.0 Typ — — — Max — 4.0 4.0 Unit ns ns ns Note: 1. The symbols used for timing specifications herein follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tMRDVKH symbolizes MII receive timing (MR) with respect to the time data input signals (D) reach the valid state (V) relative to the tMRX clock reference (K) going to the high (H) state or setup time. Also, tMRDXKL symbolizes MII receive timing (GR) with respect to the time data input signals (D) went invalid (X) relative to the tMRX clock reference (K) going to the low (L) state or hold time. Note that, in general, the clock reference symbol representation is based on three letters representing the clock of a particular functional. For example, the subscript of tMRX represents the MII (M) receive (RX) clock. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall). Figure 9 shows the MII receive AC timing diagram. tMRX RX_CLK tMRXH RXD[3:0] RX_DV RX_ER tMRDVKH tMRDXKH tMRXF Valid Data tMRXR Figure 9. MII Receive AC Timing Diagram RMII AC Timing Specifications Figure 10 provides the AC test load. Output Z0 = 50 Ω RL = 5 0 Ω NVDD/2 or LVDD/2 Figure 10. AC Test Load 8.2.2 RGMII AC Timing Specifications Table 25. RGMII AC Timing Specifications Table 25 presents the RGMII AC timing specifications. At recommended operating conditions with LVDD of 2.5 V ± 5%. Parameter/Condition Data to clock output skew (at transmitter) Data to clock input skew (at receiver) 2 Symbol 1 tSKRGT tSKRGT Min –0.6 1.0 Typ — — Max 0.6 2.6 Unit ns ns M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 18 Freescale Semiconductor Ethernet: Three-Speed Ethernet, MII Management Table 25. RGMII AC Timing Specifications (continued) At recommended operating conditions with LVDD of 2.5 V ± 5%. Clock cycle duration 3 Duty cycle for 1000Base-T 4, 5 3, 5 tRGT tRGTH/tRGT tRGTH/tRGT tRGTR tRGTF tG12 6 7.2 45 40 — — — 47 8.0 50 50 — — 8.0 — 8.8 55 60 0.75 0.75 — 53 ns % % ns ns ns % Duty cycle for 10BASE-T and 100BASE-TX Rise time (20%–80%) Fall time (20%–80%) GTX_CLK125 reference clock period GTX_CLK125 reference clock duty cycle tG125H/tG125 Notes: 1. Note that, in general, the clock reference symbol representation for this section is based on the symbols RGT to represent RGMII timing. For example, the subscript of tRGT represents the RGMII receive (RX) clock. Note also that the notation for rise (R) and fall (F) times follows the clock symbol that is being represented. For symbols representing skews, the subscript is skew (SK) followed by the clock that is being skewed (RGT). 2. This implies that PC board design requires clocks to be routed such that an additional trace delay of greater than 1.5 ns is added to the associated clock signal. 3. For 10 and 100 Mbps, tRGT scales to 400 ns ± 40 ns and 40 ns ± 4 ns, respectively. 4. Duty cycle may be stretched/shrunk during speed changes or while transitioning to a received packet's clock domains as long as the minimum duty cycle is not violated and stretching occurs for no more than three tRGT of the lowest speed transitioned between. 5. Duty cycle reference is 0.5*LVDD 6. This symbol is used to represent the external GTX_CLK125 and does not follow the original symbol naming convention. Figure 11 shows the RGMII AC timing and multiplexing diagrams. tRGT tRGTH GTX_CLK (At Transmitter) tSKRGT TXD[8:5][3:0] TXD[7:4][3:0] TXD[8:5] TXD[3:0] TXD[7:4] TXD[4] TXEN TXD[9] TXERR tSKRGT TX_CLK (At PHY) TX_CTL RXD[8:5][3:0] RXD[7:4][3:0] RXD[8:5] RXD[3:0] RXD[7:4] tSKRGT RXD[4] RXDV RXD[9] RXERR tSKRGT RX_CTL RX_CLK (At PHY) Figure 11. RGMII AC Timing and Multiplexing Diagrams M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 Freescale Semiconductor 19 Ethernet: Three-Speed Ethernet, MII Management 8.3 Ethernet Management Interface Electrical Characteristics The electrical characteristics specified here apply to MII management interface signals MDIO (management data input/output) and MDC (management data clock). The electrical characteristics for MII and RGMII are specified in Section 8.1, “Enhanced Three-Speed Ethernet Controller (eTSEC) (10/100/1000 Mbps)—MII/RGMII Electrical Characteristics.” 8.3.1 MII Management DC Electrical Characteristics The MDC and MDIO are defined to operate at a supply voltage of 3.3 V. Table 26 provides the DC electrical characteristics for MDIO and MDC. Table 26. MII Management DC Electrical Characteristics When Powered at 3.3 V Parameter Supply voltage (3.3 V) Output high voltage Output low voltage Input high voltage Input low voltage Input high current Input low current Symbol NVDD VOH VOL VIH VIL IIH IIL NVDD = Max NVDD = Max IOH = –1.0 mA IOL = 1.0 mA — — VIN 1 Conditions — NVDD = Min LVDD = Min Min 3.0 2.10 VSS 2.0 — = 2.1 V — –600 Max 3.6 NVDD + 0.3 0.50 — 0.80 40 — Unit V V V V V μA μA VIN = 0.5 V Note: 1. Note that the symbol VIN, in this case, represents the LVIN symbol referenced in Table 1 and Table 2. 8.3.2 MII Management AC Electrical Specifications Table 27. MII Management AC Timing Specifications Table 27 provides the MII management AC timing specifications. At recommended operating conditions with LVDDA/LVDDB is 3.3 V ± 0.3V Parameter/Condition MDC frequency MDC period MDC clock pulse width high MDC to MDIO delay MDIO to MDC setup time MDIO to MDC hold time MDC rise time Symbol 1 fMDC tMDC tMDCH tMDKHDX tMDDVKH tMDDXKH tMDCR Min — — 32 10 5 0 — Typ 2.5 400 — — — — — Max — — — 170 — — 10 Unit MHz ns ns ns ns ns ns Notes 2 — — 3 — — — M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 20 Freescale Semiconductor Ethernet: Three-Speed Ethernet, MII Management Table 27. MII Management AC Timing Specifications (continued) At recommended operating conditions with LVDDA/LVDDB is 3.3 V ± 0.3V Parameter/Condition MDC fall time Symbol 1 tMDHF Min — Typ — Max 10 Unit ns Notes — Notes: 1. The symbols used for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tMDKHDX symbolizes management data timing (MD) for the time tMDC from clock reference (K) high (H) until data outputs (D) are invalid (X) or data hold time. Also, tMDDVKH symbolizes management data timing (MD) with respect to the time data input signals (D) reach the valid state (V) relative to the tMDC clock reference (K) going to the high (H) state or setup time. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall). 2. This parameter is dependent on the csb_clk speed. (The MIIMCFG[Mgmt Clock Select] field determines the clock frequency of the Mgmt Clock EC_MDC.) 3. This parameter is dependent on the cbs_clk speed (that is, for a csb_clk of 133 MHz, the delay is 60 ns). Figure 12 shows the MII management AC timing diagram. tMDC MDC tMDCH MDIO (Input) tMDDVKH tMDDXKH MDIO (Output) tMDKHDX tMDCF tMDCR Figure 12. MII Management Interface Timing Diagram 8.4 IEEE Std 1588™ Timer Specifications This section describes the DC and AC electrical specifications for the 1588 timer. 8.4.1 IEEE 1588 Timer DC Specifications Table 28. GPIO DC Electrical Characteristics Characteristic Symbol VOH VOL VOL VIH Condition IOH = –8.0 mA IOL = 8.0 mA IOL = 3.2 mA — Min 2.4 — — 2.0 Max — 0.5 0.4 NVDD + 0.3 Unit V V V V Table 28 provides the IEEE 1588 timer DC specifications. Output high voltage Output low voltage Output low voltage Input high voltage M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 Freescale Semiconductor 21 USB Table 28. GPIO DC Electrical Characteristics (continued) Characteristic Input low voltage Input current Symbol VIL IIN Condition — 0 V ≤ VIN ≤ NVDD Min –0.3 — Max 0.8 ±5 Unit V μA 8.4.2 IEEE 1588 Timer AC Specifications Table 29. IEEE 1588 Timer AC Specifications Parameter Symbol tTMRCK tTMRCKS tTMRCKH tGCLKNV tTMRAL Min 0 — — 0 — Max 70 — — 6 — Unit MHz — — ns — Notes 1 2, 3 2, 3 — 2 Table 29 provides the IEEE 1588 timer AC specifications. Timer clock cycle time Input setup to timer clock Input hold from timer clock Output clock to output valid Timer alarm to output valid Notes: 1. The timer can operate on rtc_clock or tmr_clock. These clocks get muxed and any one of them can be selected. 2. Asynchronous signals. 3. Inputs need to be stable at least one TMR clock. 9 9.1 USB USB Dual-Role Controllers This section provides the AC and DC electrical specifications for the USB-ULPI interface. 9.1.1 USB DC Electrical Characteristics Table 30. USB DC Electrical Characteristics Parameter Symbol VIH VIL IIN VOH VOL Min 2 –0.3 — LVDD – 0.2 — Max LVDD + 0.3 0.8 ±5 — 0.2 Unit V V μA V V Table 30 lists the DC electrical characteristics for the USB interface. High-level input voltage Low-level input voltage Input current High-level output voltage, IOH = –100 μA Low-level output voltage, IOL = 100 μA Note: 1. The symbol VIN, in this case, represents the NV IN symbol referenced in Table 1 and Table 2. M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 22 Freescale Semiconductor USB 9.1.2 USB AC Electrical Specifications Table 31. USB General Timing Parameters Parameter Symbol 1 tUSCK tUSIVKH tUSIXKH tUSKHOV tUSKHOX Min 15 4 1 — 1 Max — — — 9 — Unit ns ns ns ns ns Notes 1, 2 1, 4 1, 4 1 1 Table 31 lists the general timing parameters of the USB-ULPI interface. USB clock cycle time Input setup to USB clock—all inputs Input hold to USB clock—all inputs USB clock to output valid—all outputs Output hold from USB clock—all outputs Notes: 1. The symbols used for timing specifications follow the pattern of t(First two letters of functional block)(signal)(state)(reference)(state) for inputs and t(First two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tUSIXKH symbolizes USB timing (US) for the input (I) to go invalid (X) with respect to the time the USB clock reference (K) goes high (H). Also, t USKHOX symbolizes USB timing (US) for the USB clock reference (K) to go high (H), with respect to the output (O) going invalid (X) or output hold time. 2. All timings are in reference to USB clock. 3. All signals are measured from NVDD/2 of the rising edge of USB clock to 0.4 × NVDD of the signal in question for 3.3-V signaling levels. 4. Input timings are measured at the pin. 5. For purposes of active/float timing measurements, the Hi-Z or off-state is defined to be when the total current delivered through the component pin is less than or equal to the leakage current specification. Figure 13 and Figure 14 provide the AC test load and signals for the USB, respectively. Output Z0 = 50 Ω RL = 5 0 Ω NVDD/2 Figure 13. USB AC Test Load USBDR_CLK tUSIVKH Input Signals tUSIXKH tUSKHOV Output Signals tUSKHOX Figure 14. USB Signals M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 Freescale Semiconductor 23 High-Speed Serial Interfaces (HSSI) 10 High-Speed Serial Interfaces (HSSI) This section describes the common portion of SerDes DC electrical specifications, which is the DC requirement for SerDes reference clocks. The SerDes data lane’s transmitter and receiver reference circuits are also shown. 10.1 Signal Terms Definition The SerDes utilizes differential signaling to transfer data across the serial link. This section defines terms used in the description and specification of differential signals. Figure 15 shows how the signals are defined. For illustration purpose, only one SerDes lane is used for description. The figure shows waveform for either a transmitter output (TXn and TXn) or a receiver input (RXn and RXn). Each signal swings between A Volts and B Volts where A > B. Using this waveform, the definitions are as follows. To simplify illustration, the following definitions assume that the SerDes transmitter and receiver operate in a fully symmetrical differential signaling environment. 1. Single-Ended Swing The transmitter output signals and the receiver input signals TXn, TXn, RXn, and RXn each have a peak-to-peak swing of A – B Volts. This is also referred as each signal wire’s single-ended swing. 2. Differential Output Voltage, VOD (or Differential Output Swing) The differential output voltage (or swing) of the transmitter, VOD, is defined as the difference of the two complimentary output voltages: VTXn – VTXn. The VOD value can be either positive or negative. 3. Differential Input Voltage, VID (or Differential Input Swing) The differential input voltage (or swing) of the receiver, VID, is defined as the difference of the two complimentary input voltages: VRXn – VRXn. The VID value can be either positive or negative. 4. Differential Peak Voltage, VDIFFp The peak value of the differential transmitter output signal or the differential receiver input signal is defined as differential peak voltage, VDIFFp = |A – B| Volts. 5. Differential Peak-to-Peak, VDIFFp-p Since the differential output signal of the transmitter and the differential input signal of the receiver each range from A – B to –(A – B) Volts, the peak-to-peak value of the differential transmitter output signal or the differential receiver input signal is defined as differential peak-to-peak voltage, VDIFFp-p = 2*VDIFFp = 2 * |(A – B)| Volts, which is twice of differential swing in amplitude, or twice of the differential peak. For example, the output differential peak–peak voltage can also be calculated as VTX-DIFFp-p = 2*|VOD|. 6. Differential Waveform The differential waveform is constructed by subtracting the inverting signal (TXn, for example) from the non-inverting signal (TXn, for example) within a differential pair. There is only one signal trace curve in a differential waveform. The voltage represented in the differential waveform is not referenced to ground. Refer to Figure 24 as an example for differential waveform. M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 24 Freescale Semiconductor High-Speed Serial Interfaces (HSSI) 7. Common Mode Voltage, Vcm The common mode voltage is equal to one-half of the sum of the voltages between each conductor of a balanced interchange circuit and ground. In this example, for SerDes output, Vcm_out = (VTXn + VTXn )/2 = (A + B) / 2, which is the arithmetic mean of the two complimentary output voltages within a differential pair. In a system, the common mode voltage may often differ from one component’s output to the other’s input. Sometimes, it may be even different between the receiver input and driver output circuits within the same component. It is also referred as the DC offset in some occasion. TX n or RXn A Volts Vcm = (A + B) / 2 TXn or RXn B Volts Differential Swing, VID or VOD = A – B Differential Peak Voltage, VDIFFp = |A – B| Differential Peak–Peak Voltage, VDIFFpp = 2*VDIFFp (not shown) Figure 15. Differential Voltage Definitions for Transmitter or Receiver To illustrate these definitions using real values, consider the case of a CML (current mode logic) transmitter that has a common mode voltage of 2.25 V and each of its outputs, TD and TD, has a swing that goes between 2.5 V and 2.0 V. Using these values, the peak-to-peak voltage swing of each signal (TD or TD) is 500 mV p-p, which is referred as the single-ended swing for each signal. In this example, since the differential signaling environment is fully symmetrical, the transmitter output’s differential swing (VOD) has the same amplitude as each signal’s single-ended swing. The differential output signal ranges between 500 mV and –500 mV; in other words, VOD is 500 mV in one phase and –500 mV in the other phase. The peak differential voltage (VDIFFp) is 500 mV. The peak-to-peak differential voltage (VDIFFp-p) is 1000 mV p-p. 10.2 SerDes Reference Clocks The SerDes reference clock inputs are applied to an internal PLL whose output creates the clock used by the corresponding SerDes lanes. The SerDes reference clocks input is SD_REF_CLK and SD_REF_CLK for PCI Express. The following sections describe the SerDes reference clock requirements and some application information. 10.2.1 SerDes Reference Clock Receiver Characteristics Figure 16 shows a receiver reference diagram of the SerDes reference clocks. M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 Freescale Semiconductor 25 High-Speed Serial Interfaces (HSSI) • • • • The supply voltage requirements for XCOREVDD are specified in Table 1 and Table 2. SerDes reference clock receiver reference circuit structure — The SD_REF_CLK and SD_REF_CLK are internally AC-coupled differential inputs as shown in Figure 16. Each differential clock input (SD_REF_CLK or SD_REF_CLK) has a 50-Ω termination to XCOREVSS followed by on-chip AC-coupling. — The external reference clock driver must be able to drive this termination. — The SerDes reference clock input can be either differential or single ended. Refer to the Differential Mode and Single-ended Mode description below for further detailed requirements. The maximum average current requirement that also determines the common mode voltage range — When the SerDes reference clock differential inputs are DC-coupled externally with the clock driver chip, the maximum average current allowed for each input pin is 8 mA. In this case, the exact common mode input voltage is not critical as long as it is within the range allowed by the maximum average current of 8 mA (refer to the following bullet for more detail), since the input is AC-coupled on-chip. — This current limitation sets the maximum common mode input voltage to be less than 0.4 V (0.4 V/50 = 8 mA) while the minimum common mode input level is 0.1 V above XCOREVSS. For example, a clock with a 50/50 duty cycle can be produced by a clock driver with output driven by its current source from 0 mA to 16 mA (0–0.8 V), such that each phase of the differential input has a single-ended swing from 0 V to 800 mV with the common mode voltage at 400 mV. — If the device driving the SD_REF_CLK and SD_REF_CLK inputs cannot drive 50 Ω to XCOREVSS DC, or it exceeds the maximum input current limitations, then it must be AC-coupled off-chip. The input amplitude requirement — This requirement is described in detail in the following sections. 50 Ω SD_REF_CLK Input Amp SD_REF_CLK 50 Ω Figure 16. Receiver of SerDes Reference Clocks M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 26 Freescale Semiconductor High-Speed Serial Interfaces (HSSI) 10.2.2 DC Level Requirement for SerDes Reference Clocks The DC level requirement for the MPC8308 SerDes reference clock inputs is different depending on the signaling mode used to connect the clock driver chip and SerDes reference clock inputs as described below. • Differential Mode — The input amplitude of the differential clock must be between 400 mV and 1600 mV differential peak–peak (or between 200 mV and 800 mV differential peak). In other words, each signal wire of the differential pair must have a single-ended swing less than 800 mV and greater than 200 mV. This requirement is the same for both external DC-coupled or AC-coupled connection. — For external DC-coupled connection, as described in Section 10.2.1, “SerDes Reference Clock Receiver Characteristics,” the maximum average current requirements sets the requirement for average voltage (common mode voltage) to be between 100 mV and 400 mV. Figure 17 shows the SerDes reference clock input requirement for DC-coupled connection scheme. — For external AC-coupled connection, there is no common mode voltage requirement for the clock driver. Since the external AC-coupling capacitor blocks the DC level, the clock driver and the SerDes reference clock receiver operate in different command mode voltages. The SerDes reference clock receiver in this connection scheme has its common mode voltage set to XCOREVSS. Each signal wire of the differential inputs is allowed to swing below and above the common mode voltage (XCOREVSS). Figure 18 shows the SerDes reference clock input requirement for AC-coupled connection scheme. • Single-Ended Mode — The reference clock can also be single ended. The SD_REF_CLK input amplitude (single-ended swing) must be between 400 mV and 800 mV peak–peak (from Vmin to Vmax) with SD_REF_CLK either left unconnected or tied to ground. — The SD_REF_CLK input average voltage must be between 200 and 400 mV. Figure 19 shows the SerDes reference clock input requirement for single-ended signaling mode. — To meet the input amplitude requirement, the reference clock inputs might need to be DC- or AC-coupled externally. For the best noise performance, the reference of the clock could be DCor AC-coupled into the unused phase (SD_REF_CLK) through the same source impedance as the clock input (SD_REF_CLK) in use. M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 Freescale Semiconductor 27 High-Speed Serial Interfaces (HSSI) SD_REF_CLK 200 mV < Input Amplitude or Differential Peak < 800 mV Vmax < 80 0mV 100 mV < Vcm < 400 mV SD_REF_CLK Vmin > 0 V Figure 17. Differential Reference Clock Input DC Requirements (External DC-Coupled) 200mV < Input Amplitude or Differential Peak < 800mV SD_REF_CLK Vmax < Vcm + 400 mV Vcm SD_REF_CLK Vmin > Vcm – 400 mV Figure 18. Differential Reference Clock Input DC Requirements (External AC-Coupled) 400 mV < SD_REF_CLK Input Amplitude < 800 mV SD_REF_CLK 0V SD_REF_CLK Figure 19. Single-Ended Reference Clock Input DC Requirements 10.2.3 Interfacing with Other Differential Signaling Levels With on-chip termination to XCOREVSS, the differential reference clocks inputs are high-speed current steering logic (HCSL)-compatible and DC-coupled. Many other low-voltage differential type outputs like low-voltage differential signaling (LVDS) can be used but may need to be AC-coupled due to the limited common mode input range allowed (100–400 mV) for DC-coupled connection. LVPECL outputs can produce signal with too large amplitude and may need to be DC-biased at clock driver output first, then followed with series attenuation resistor to reduce the amplitude, in addition to AC-coupling. M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 28 Freescale Semiconductor High-Speed Serial Interfaces (HSSI) NOTE Figure 20 to Figure 23 below are for conceptual reference only. Due to the fact that clock driver chip's internal structure, output impedance, and termination requirements are different between various clock driver chip manufacturers, it is very possible that the clock circuit reference designs provided by clock driver chip vendor are different from what is shown below. They might also vary from one vendor to the other. Therefore, Freescale Semiconductor can neither provide the optimal clock driver reference circuits, nor guarantee the correctness of the following clock driver connection reference circuits. The system designer is recommended to contact the selected clock driver chip vendor for the optimal reference circuits with the MPC8308 SerDes reference clock receiver requirement provided in this document. Figure 20 shows the SerDes reference clock connection reference circuits for HCSL type clock driver. It assumes that the DC levels of the clock driver chip is compatible with MPC8308 SerDes reference clock input’s DC requirement. HCSL CLK Driver Chip CLK_Out 33 Ω SD_REF_CLK 50 Ω MPC8308 Clock Driver 33 Ω CLK_Out CLK_Out 100 Ω differential PWB trace SerDes Refer. CLK Receiver SD_REF_CLK 50 Ω Total 50 Ω. Assume clock driver’s output impedance is about 16 Ω. Clock driver vendor dependent source termination resistor Figure 20. DC-Coupled Differential Connection with HCSL Clock Driver (Reference Only) M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 Freescale Semiconductor 29 High-Speed Serial Interfaces (HSSI) Figure 21 shows the SerDes reference clock connection reference circuits for LVDS type clock driver. Since LVDS clock driver’s common mode voltage is higher than the MPC8308’s SerDes reference clock input’s allowed range (100–400 mV), AC-coupled connection scheme must be used. It assumes the LVDS output driver features 50-Ω termination resistor. It also assumes that the LVDS transmitter establishes its own common mode level without relying on the receiver or other external component. LVDS CLK Driver Chip CLK_Out 10 nF SD_REF_CLK 50 Ω MPC8308 Clock Driver 100 Ω differential PWB trace SerDes Refer. CLK Receiver CLK_Out 10 nF SD_REF_CLK 50 Ω Figure 21. AC-Coupled Differential Connection with LVDS Clock Driver (Reference Only) M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 30 Freescale Semiconductor High-Speed Serial Interfaces (HSSI) Figure 22 shows the SerDes reference clock connection reference circuits for LVPECL type clock driver. Since LVPECL driver’s DC levels (both common mode voltages and output swing) are incompatible with MPC8308 SerDes reference clock input’s DC requirement, AC-coupling has to be used. Figure 22 assumes that the LVPECL clock driver’s output impedance is 50 Ω. R1 is used to DC-bias the LVPECL outputs prior to AC-coupling. Its value could be ranged from 140 Ω to 240 Ω depending on clock driver vendor’s requirement. R2 is used together with the SerDes reference clock receiver’s 50-Ω termination resistor to attenuate the LVPECL output’s differential peak level such that it meets the MPC8308’s SerDes reference clock’s differential input amplitude requirement (between 200 mV and 800 mV differential peak). For example, if the LVPECL output’s differential peak is 900 mV and the desired SerDes reference clock input amplitude is selected as 600 mV, the attenuation factor is 0.67, which requires R2 = 25 Ω. Consult clock driver chip manufacturer to verify whether this connection scheme is compatible with a particular clock driver chip. LVPECL CLK Driver Chip CLK_Out R2 10nF SD_REF_CLK MPC8308 50 Ω Clock Driver R1 100 Ω differential PWB trace R2 10 nF SD_REF_CLK SerDes Refer. CLK Receiver CLK_Out R1 50 Ω Figure 22. AC-Coupled Differential Connection with LVPECL Clock Driver (Reference Only) M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 Freescale Semiconductor 31 High-Speed Serial Interfaces (HSSI) Figure 23 shows the SerDes reference clock connection reference circuits for a single-ended clock driver. It assumes the DC levels of the clock driver are compatible with the device’s SerDes reference clock input’s DC requirement. Single-Ended CLK Driver Chip Total 50 Ω. Assume clock driver’s output impedance is about 16 Ω. 33 Ω CLK_Out SD_REF_CLK 50 Ω MPC8308 Clock Driver 100 Ω differential PWB trace SerDes Refer. CLK Receiver 50 Ω SD_REF_CLK 50 Ω Figure 23. Single-Ended Connection (Reference Only) 10.2.4 AC Requirements for SerDes Reference Clocks The clock driver selected should provide a high-quality reference clock with low-phase noise and cycle-to-cycle jitter. Phase noise less than 100 kHz can be tracked by the PLL and data recovery loops, and is less of a problem. Phase noise above 15 MHz is filtered by the PLL. The most problematic phase noise occurs in the 1–15 MHz range. The source impedance of the clock driver should be 50 Ω to match the transmission line and reduce reflections which are a source of noise to the system. Table 32 describes some AC parameters for PCI Express protocol. Table 32. SerDes Reference Clock AC Parameters At recommended operating conditions with XCOREVDD= 1.0V ± 5% Parameter Rising Edge Rate Falling Edge Rate Differential Input High Voltage Differential Input Low Voltage Symbol Rise Edge Rate Fall Edge Rate VIH VIL Min 1.0 1.0 +200 — Max 4.0 4.0 — –200 Unit V/ns V/ns mV mV Notes 2, 3 2, 3 2 2 M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 32 Freescale Semiconductor High-Speed Serial Interfaces (HSSI) Table 32. SerDes Reference Clock AC Parameters (continued) At recommended operating conditions with XCOREVDD= 1.0V ± 5% Parameter Rising edge rate (SD_REF_CLK) to falling edge rate (SD_REF_CLK) matching Symbol Rise-Fall Matching Min — Max 20 Unit % Notes 1, 4 Notes: 1. Measurement taken from single-ended waveform. 2. Measurement taken from differential waveform. 3. Measured from –200 mV to +200 mV on the differential waveform (derived from SD_REF_CLK minus SD_REF_CLK). The signal must be monotonic through the measurement region for rise and fall time. The 400 mV measurement window is centered on the differential zero crossing (Figure 24). 4. Matching applies to rising edge rate for SD_REF_CLK and falling edge rate for SD_REF_CLK. It is measured using a 200 mV window centered on the median cross point where SD_REF_CLK rising meets SD_REF_CLK falling. The median cross point is used to calculate the voltage thresholds the oscilloscope is to use for the edge rate calculations. The Rise Edge Rate of SD_REF_CLK should be compared to the Fall Edge Rate of SD_REF_CLK, the maximum allowed difference should not exceed 20% of the slowest edge rate (See Figure 25). VIH = +200 0.0 V VIL = -200 mV SD_REF_CLK minus SD_REF_CLK Figure 24. Differential Measurement Points for Rise and Fall Time SD_REF_CLK SD_REF_CLK SD_REF_CLK SD_REF_CLK Figure 25. Single-Ended Measurement Points for Rise and Fall Time Matching The other detailed AC requirements of the SerDes reference clocks is defined by each interface protocol based on application usage. For detailed information, see Section 11.2, “AC Requirements for PCI Express SerDes Clocks.” M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 Freescale Semiconductor 33 PCI Express 10.2.4.1 Spread Spectrum Clock SD_REF_CLK/SD_REF_CLK are not intended to be used with, and should not be clocked by, a spread spectrum clock source. 10.3 SerDes Transmitter and Receiver Reference Circuits Figure 26 shows the reference circuits for SerDes data lane’s transmitter and receiver. TXn 50 Ω Transmitter 50 Ω TXn RXn 50 Ω 50 Ω Receiver RXn Figure 26. SerDes Transmitter and Receiver Reference Circuits The DC and AC specification of SerDes data lanes are defined in Section 11, “PCI Express.” Note that external AC-coupling capacitor is required for the PCI Express serial transmission protocol with the capacitor value defined in specification of PCI Express protocol section. 11 PCI Express This section describes the DC and AC electrical specifications for the PCI Express bus. 11.1 DC Requirements for PCI Express SD_REF_CLK and SD_REF_CLK For more information, see Section 10.2, “SerDes Reference Clocks.” 11.2 AC Requirements for PCI Express SerDes Clocks Table 33. SD_REF_CLK and SD_REF_CLK AC Requirements Table 33 lists the PCI Express SerDes clock AC requirements. Symbol tREF tREFCJ tREFPJ Parameter Description REFCLK cycle time (for 125 MHz and 100 MHz) REFCLK cycle-to-cycle jitter. Difference in the period of any two adjacent REFCLK cycles. Phase jitter. Deviation in edge location with respect to mean edge location. Min 8 — –50 Typ 10 — — Max — 100 50 Units ns ps ps Notes — — — M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 34 Freescale Semiconductor PCI Express 11.3 Clocking Dependencies The ports on the two ends of a link must transmit data at a rate that is within 600 parts per million (ppm) of each other at all times. This is specified to allow bit rate clock sources with a ±300 ppm tolerance. 11.4 Physical Layer Specifications Following is a summary of the specifications for the physical layer of PCI Express on this device. For further details as well as the specifications of the transport and data link layer, use the PCI Express Base Specification, Rev. 1.0a. 11.4.1 Differential Transmitter (TX) Output Table 34 defines the specifications for the differential output at all transmitters (TXs). The parameters are specified at the component pins. Table 34. Differential Transmitter (TX) Output Specifications Parameter Unit interval Symbol UI Comments Each UPETX is 400 ps ± 300 ppm. U PETX does not account for Spread Spectrum Clock dictated variations. VPEDPPTX = 2*|VTX-D+ VTX-D-| Ratio of the VPEDPPTX of the second and following bits after a transition divided by the VPEDPPTX of the first bit after a transition. The maximum Transmitter jitter can be derived as TTX-MAX-JITTER = 1 UPEEWTX= 0.3 UI. Min 399.88 Typical 400 Max 400.12 Units ps Notes 1 Differential peak-to-peak output voltage De-emphasized differential output voltage (ratio) VTX-DIFFp-p VTX-DE-RATIO 0.8 –3.0 — –3.5 1.2 –4.0 V dB 2 2 Minimum TX eye width TTX-EYE 0.70 — — UI 2, 3 Maximum time between the jitter median and maximum deviation from the median TTX-EYE-MEDIAN-t Jitter is defined as the measurement variation of othe crossing points MAX-JITTER (VPEDPPTX = 0 V) in relation to a recovered TX UI. A recovered TX UI is calculated over 3500 consecutive unit intervals of sample data. Jitter is measured using all edges of the 250 consecutive UI in the center of the 3500 UI used for calculating the TX UI. — — 0.15 UI 2, 3 M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 Freescale Semiconductor 35 PCI Express Table 34. Differential Transmitter (TX) Output Specifications (continued) Parameter D+/D- TX output rise/fall time RMS AC peak common mode output voltage Symbol TTX-RISE, TTX-FALL VTX-CM-ACp Comments — VPEACPCMTX = RMS(|VTXD+ + VTXD-|/2 VTX-CM-DC) VTX-CM-DC = DC(avg) of |VTX-D+ + VTX-D-|/2 |VTX-CM-DC (during L0) VTX-CM-Idle-DC (During Electrical Idle)| 175 mV 0.4 UI = T RX-EYE-MIN Figure 28. Minimum Receiver Eye Timing and Voltage Compliance Specification 11.5.1 Compliance Test and Measurement Load The AC timing and voltage parameters must be verified at the measurement point, as specified within 0.2 inches of the package pins, into a test/measurement load shown in Figure 29. NOTE The allowance of the measurement point to be within 0.2 inches of the package pins is meant to acknowledge that package/board routing may benefit from D+ and D– not being exactly matched in length at the package pin boundary. M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 42 Freescale Semiconductor Enhanced Local Bus Figure 29. Compliance Test/Measurement Load 12 Enhanced Local Bus This section describes the DC and AC electrical specifications for the enhanced local bus interface. 12.1 Enhanced Local Bus DC Electrical Characteristics Table 36. Local Bus DC Electrical Characteristics at 3.3 V Parameter Symbol VIH VIL IIN VOH VOL Min 2.0 –0.3 — NVDD – 0.2 — Max NVDD + 0.3 0.8 ±5 — 0.2 Unit V V μA V V Table 36 provides the DC electrical characteristics for the local bus interface. High-level input voltage Low-level input voltage Input current, (VIN1 = 0 V or VIN = LVDD) High-level output voltage, (LVDD = min, IOH = –2 mA) Low-level output voltage, (LVDD = min, IOH = 2 mA) Note: The parameters stated in above table are valid for all revisions unless explicitly mentioned. 12.2 Enhanced Local Bus AC Electrical Specifications Table 37. Local Bus General Timing Parameters Parameter Symbol 1 tLBK tLBIVKH tLBIXKH Min 15 7 1 Max — — — Unit ns ns ns Notes 2 3, 4 3, 4 Table 37 describes the general timing parameters of the local bus interface. Local bus cycle time Input setup to local bus clock (Note: to be revisited) Input hold from local bus clock (Note: to be revisited) M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 Freescale Semiconductor 43 Enhanced Local Bus Table 37. Local Bus General Timing Parameters (continued) Parameter Local bus clock to output valid (Note: to be revisited) Local bus clock to output high impedance for LD (Note: to be revisited) Symbol 1 tLBKHOV tLBKHOZ Min — — Max 3 4 Unit ns ns Notes 3 5 Notes: 1. The symbols used for timing specifications follow the pattern of t(First two letters of functional block)(signal)(state) (reference)(state) for inputs and t(First two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tLBIXKH1 symbolizes local bus timing (LB) for the input (I) to go invalid (X) with respect to the time the tLBK clock reference (K) goes high (H), in this case for clock one(1). 2. All timings are in reference to falling edge of LCLK0 (for all outputs and for LGTA and LUPWAIT inputs) or rising edge of LCLK0 (for all other inputs). 3. All signals are measured from NVDD/2 of the rising/falling edge of LCLK0 to 0.4 × NVDD of the signal in question for 3.3-V signaling levels. 4. Input timings are measured at the pin. 5. For purposes of active/float timing measurements, the Hi-Z or off state is defined to be when the total current delivered through the component pin is less than or equal to the leakage current specification. Figure 30 provides the AC test load for the local bus. Output Z0 = 50 Ω RL = 5 0 Ω NVDD/2 Figure 30. Local Bus AC Test Load M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 44 Freescale Semiconductor Enhanced Local Bus Figure 31 through Figure 33 show the local bus signals. In what follows, T1, T2, T3, and T4 are internal clock reference phase signals corresponding to LCCR[CLKDIV]. LCLK0 tLBIVKH Input Signals: LD[0:15] tLBIVKH Input Signal: LGTA tLBIXKH Output Signals: tLBKHOV tLBIXKH tLBIXKH LBCTL//LOE/ Output Signals: LA[0:25] tLBKHOV tLBKHOZ Figure 31. Local Bus Signals, Non-Special Signals Only M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 Freescale Semiconductor 45 Enhanced Local Bus LCLK0 T1 T3 tLBKHOV GPCM Mode Output Signals: LCS[0:3]/LWE tLBIVKH UPM Mode Input Signal: LUPWAIT tLBIVKH tLBIXKH tLBIXKH tLBKHOZ Input Signals: LD[0:15] tLBKHOV UPM Mode Output Signals: LCS[0:3]/LBS[0:1]/LGPL[0:5] tLBKHOZ Figure 32. Local Bus Signals, GPCM/UPM Signals for LCCR[CLKDIV] = 2 M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 46 Freescale Semiconductor Enhanced Secure Digital Host Controller (eSDHC) LCLK T1 T2 T3 T4 tLBKHOV GPCM Mode Output Signals: LCS[0:3]/LWE tLBIVKH UPM Mode Input Signal: LUPWAIT tLBIVKH tLBIXKH tLBIXKH tLBKHOZ Input Signals: LD[0:15] tLBKHOV UPM Mode Output Signals: LCS[0:3]/LBS[0:1]/LGPL[0:5] tLBKHOZ Figure 33. Local Bus Signals, GPCM/UPM Signals for LCCR[CLKDIV] = 4 13 Enhanced Secure Digital Host Controller (eSDHC) This section describes the DC and AC electrical specifications for the eSDHC (SD/MMC/SDIO) interface of the MPC8308. The eSDHC controller always uses the falling edge of the SD_CLK in order to drive the SD_DAT[0:3]/CMD as outputs and rising edge to sample the SD_DAT[0:3], CMD, CD, and WP as inputs. This behavior is true for both full- and high-speed modes. 13.1 eSDHC DC Electrical Characteristics Table 38 provides the DC electrical characteristics for the eSDHC (SD/MMC) interface of the device, compatible with SDHC specifications. The eSDHC NVDD range is between 3.0 V and 3.6 V. Table 38. eSDHC interface DC Electrical Characteristics Characteristic Output high voltage Output low voltage Symbol VOH VOL Condition IOH = –8.0 mA IOL = 8.0 mA Min 2.4 — Max — 0.5 Unit V V M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 Freescale Semiconductor 47 Enhanced Secure Digital Host Controller (eSDHC) Table 38. eSDHC interface DC Electrical Characteristics (continued) Characteristic Output low voltage Input high voltage Input low voltage Symbol VOL VIH VIL Condition IOL = 3.2 mA — — Min — 2.1 –0.3 Max 0.4 NVDD + 0.3 0.8 Unit V V V 13.2 eSDHC AC Timing Specifications (Full-Speed Mode) This section describes the AC electrical specifications for the eSDHC (SD/MMC) interface of the device. Table 39 provides the eSDHC AC timing specifications for full-speed mode as defined in Figure 35 and Figure 36. Table 39. eSDHC AC Timing Specifications for Full-Speed Mode At recommended operating conditions NV DD = 3.3 V ± 300 mV. Parameter SD_CLK clock frequency—full-speed mode SD_CLK clock cycle SD_CLK clock frequency—identification mode SD_CLK clock low time SD_CLK clock high time SD_CLK clock rise and fall times Input setup times: SD_CMD, SD_DATx to SD_CLK Input hold times: SD_CMD, SD_DATx to SD_CLK Output valid: SD_CLK to SD_CMD, SD_DATx valid Output hold: SD_CLK to SD_CMD, SD_DATx valid SD card input setup SD card input hold SD card output valid SD card output hold Symbol 1 fSFSCK tSFSCK fSIDCK tSFSCKL tSFSCKH tSFSCKR/ tSFSCKF tSFSIVKH tSFSIXKH tSFSKHOV tSFSKHOX tISU tIH tODLY tOH Min 0 40 0 15 15 — 3 2 — –3 5 5 — 0 Max 25 — 400 — — 5 — — 3 — — — 14 — Unit MHz ns kHz ns ns ns ns ns ns — ns ns ns ns Notes — — — 2 2 2 2 2 2 — 3 3 3 3 Notes: 1 The symbols used for timing specifications herein follow the pattern of t (first three letters of functional block)(signal)(state) (reference)(state) for inputs and t(first three letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tSFSIXKH symbolizes eSDHC full mode speed device timing (SFS) input (I) to go invalid (X) with respect to the clock reference (K) going to high (H). Also tSFSKHOV symbolizes eSDHC full-speed timing (SFS) for the clock reference (K) to go high (H), with respect to the output (O) going valid (V) or data output valid time. Note that, in general, the clock reference symbol representation is based on five letters representing the clock of a particular functional. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall). 2 Measured at capacitive load of 40 pF. 3 For reference only, according to the SD card specifications. 4 Average, for reference only. M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 48 Freescale Semiconductor Enhanced Secure Digital Host Controller (eSDHC) Figure 34 provides the eSDHC clock input timing diagram. eSDHC External Clock operational mode VM VM VM tSFSCKL tSFSCK VM = Midpoint Voltage (NVDD/2) tSFSCKR tSFSCKF tSFSCKH Figure 34. eSDHC Clock Input Timing Diagram 13.2.1 Full-Speed Output Path (Write) Figure 35 provides the data and command output timing diagram. tSFSCK (Clock Cycle) SD CLK at the MPC8308 Pin Driving Edge tCLK_DELAY SD CLK at the Card Pin Output Valid Time: tSFSKHOV Output Hold Time: tSFSKHOX Output from the MPC8308 Pins tSFSCKL Sampling Edge Input at the MPC8308 Pins tDATA_DELAY tISU (5 ns) tIH (5 ns) Figure 35. Full-Speed Output Path M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 Freescale Semiconductor 49 Enhanced Secure Digital Host Controller (eSDHC) 13.2.2 Full-Speed Input Path (Read) Figure 36 provides the data and command input timing diagram. tSFSCK (Clock Cycle) SD CLK at the MPC8308 Pin tCLK_DELAY SD CLK at the Card Pin Driving Edge tODLY tOH Output from the SD Card Pins Sampling Edge tDATA_DELAY Input at the MPC8308 Pins tSFSIXKH tSFSIVKH (MPC8308 Input Hold) Figure 36. Full-Speed Input Path 13.3 eSDHC AC Timing Specifications Table 40. eSDHC AC Timing Specifications for High-Speed Mode Table 40 provides the eSDHC AC timing specifications. At recommended operating conditions NVDD = 3.3 V ± 300 mV. Parameter SD_CLK clock frequency—high-speed mode SD_CLK clock cycle SD_CLK clock frequency—identification mode SD_CLK clock low time SD_CLK clock high time SD_CLK clock rise and fall times Input setup times: SD_CMD, SD_DATx Input hold times: SD_CMD, SD_DATx Output delay time: SD_CLK to SD_CMD, SD_DATx valid Output Hold time: SD_CLK to SD_CMD, SD_DATx invalid SD Card Input Setup SD Card Input Hold Symbol 1 fSHSCK tSHSCK fSIDCK tSHSCKL tSHSCKH tSHSCKR/ tSHSCKF tSHSIVKH tSHSIXKH tSHSKHOV tSHSKHOX tISU tIH Min 0 20 0 7 7 — 3 2 3 –3 6 2 Max 50 — 400 — — 3 — — — — — — Unit MHz ns kHz ns ns ns ns ns ns ns ns ns Notes 3 — — 2 2 2 2 2 2 2 3 3 M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 50 Freescale Semiconductor Enhanced Secure Digital Host Controller (eSDHC) Table 40. eSDHC AC Timing Specifications for High-Speed Mode (continued) At recommended operating conditions NVDD = 3.3 V ± 300 mV. Parameter SD Card Output Valid SD Card Output Hold 1 Symbol 1 tODLY tOH Min — 2.5 Max 14 — Unit ns ns Notes 3 3 Notes: The symbols used for timing specifications herein follow the pattern of t(first three letters of functional block)(signal)(state) (reference)(state) for inputs and t(first three letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tSFSIXKH symbolizes eSDHC full mode speed device timing (SFS) input (I) to go invalid (X) with respect to the clock reference (K) going to high (H). Also tSFSKHOV symbolizes eSDHC full-speed timing (SFS) for the clock reference (K) to go high (H), with respect to the output (O) going valid (V) or data output valid time. Note that, in general, the clock reference symbol representation is based on five letters representing the clock of a particular functional. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall). 2 Measured at capacitive load of 40 pF. 3 For reference only, according to the SD card specifications. Figure 37 provides the eSDHC clock input timing diagram. eSDHC External Clock operational mode VM VM VM tSHSCKL tSHSCK VM = Midpoint Voltage (NVDD/2) tSHSCKR tSHSCKF tSHSCKH Figure 37. eSDHC Clock Input Timing Diagram M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 Freescale Semiconductor 51 Enhanced Secure Digital Host Controller (eSDHC) 13.3.1 High-Speed Output Path (Write) Figure 38 provides the data and command output timing diagram. tSHSCK (Clock Cycle) SD CLK at the MPC8308 Pin Driving Edge tCLK_DELAY SD CLK at the Card Pin Output Valid Time: tSHSKHOV Output Hold Time: tSHSKHOX Output from the MPC8308 Pins tSHSCKL Sampling Edge Input at the SD Card Pins tDATA_DELAY tISU (6 ns) tIH (2 ns) Figure 38. High-Speed Output Path 13.3.2 High-Speed Input Path (Read) Figure 39 provides the data and command input timing diagram. tSHSCK (Clock Cycle) 1/2 Cycle SD CLK at the MPC8308 Pin tCLK_DELAY SD CLK at the Card Pin Driving Edge tODLY tOH Output from the SD Card Pins tDATA_DELAY Sampling Edge Input at the MPC8308 Pins tSHSIVKH (MPC8308 Input (MPC8308 Input tSHSIXKH Figure 39. High-Speed Input Path M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 52 Freescale Semiconductor JTAG 14 JTAG This section describes the DC and AC electrical specifications for the IEEE Std 1149.1™ (JTAG) interface. 14.1 JTAG DC Electrical Characteristics Table 41. JTAG Interface DC Electrical Characteristics Characteristic Input high voltage Input low voltage Input current Output high voltage Output low voltage Output low voltage Symbol VIH VIL IIN VOH VOL VOL Condition — — — IOH = –8.0 mA IOL = 8.0 mA IOL = 3.2 mA 2.4 — — Min 2.1 –0.3 Max NVDD + 0.3 0.8 ±5 — 0.5 0.4 Unit V V μA V V V Table 41 provides the DC electrical characteristics for the IEEE 1149.1 (JTAG) interface. 14.2 JTAG AC Timing Specifications This section describes the AC electrical specifications for the IEEE 1149.1 (JTAG) interface. Table 42 provides the JTAG AC timing specifications as defined in Figure 41 through Figure 44. Table 42. JTAG AC Timing Specifications (Independent of SYS_CLK_IN) 1 At recommended operating conditions (see Table 2). Parameter JTAG external clock frequency of operation JTAG external clock cycle time JTAG external clock pulse width measured at 1.4 V JTAG external clock rise and fall times TRST assert time Input setup times: Boundary-scan data TMS, TDI Input hold times: Boundary-scan data TMS, TDI Valid times: Boundary-scan data TDO Symbol2 fJTG t JTG tJTKHKL tJTGR & tJTGF tTRST tJTDVKH tJTIVKH tJTDXKH tJTIXKH tJTKLDV tJTKLOV Min 0 30 15 0 25 4 4 10 10 2 2 Max 33.3 — — 2 — — — Unit MHz ns ns ns ns ns Notes — — — — 3 4 ns — — ns 11 11 5 4 M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 Freescale Semiconductor 53 JTAG Table 42. JTAG AC Timing Specifications (Independent of SYS_CLK_IN) 1 (continued) At recommended operating conditions (see Table 2). Parameter Output hold times: Boundary-scan data TDO JTAG external clock to output high impedance: Boundary-scan data TDO Symbol2 Min Max Unit Notes tJTKLDX tJTKLOX tJTKLDZ tJTKLOZ 2 2 2 2 — — 19 9 ns 5 ns 5, 6 Notes: 1. All outputs are measured from the midpoint voltage of the falling/rising edge of tTCLK to the midpoint of the signal in question. The output timings are measured at the pins. All output timings assume a purely resistive 50-Ω load (see Figure 40). Time-of-flight delays must be added for trace lengths, vias, and connectors in the system. 2. The symbols used for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tJTDVKH symbolizes JTAG device timing (JT) with respect to the time data input signals (D) reaching the valid state (V) relative to the tJTG clock reference (K) going to the high (H) state or setup time. Also, tJTDXKH symbolizes JTAG timing (JT) with respect to the time data input signals (D) went invalid (X) relative to the tJTG clock reference (K) going to the high (H) state. Note that, in general, the clock reference symbol representation is based on three letters representing the clock of a particular functional. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall). 3. TRST is an asynchronous level sensitive signal. The setup time is for test purposes only. 4. Non-JTAG signal input timing with respect to tTCLK. 5. Non-JTAG signal output timing with respect to tTCLK. 6. Guaranteed by design and characterization. Figure 40 provides the AC test load for TDO and the boundary-scan outputs. Output Z0 = 50 Ω R L = 50 Ω NVDD/2 Figure 40. AC Test Load for the JTAG Interface Figure 41 provides the JTAG clock input timing diagram. JTAG External Clock VM tJTKHKL tJTG VM = Midpoint Voltage (NV DD/2) VM VM tJTGR tJTGF Figure 41. JTAG Clock Input Timing Diagram M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 54 Freescale Semiconductor JTAG Figure 42 provides the TRST timing diagram. TRST VM tTRST VM = Midpoint Voltage (NVDD/2) VM Figure 42. TRST Timing Diagram Figure 43 provides the boundary-scan timing diagram. JTAG External Clock VM tJTDVKH tJTDXKH Boundary Data Inputs tJTKLDV tJTKLDX Boundary Data Outputs tJTKLDZ Boundary Data Outputs Output Data Valid VM = Midpoint Voltage (NVDD /2) Output Data Valid Input Data Valid VM Figure 43. Boundary-Scan Timing Diagram Figure 44 provides the test access port timing diagram. JTAG External Clock VM tJTIVKH tJTIXKH TDI, TMS tJTKLOV tJTKLOX TDO tJTKLOZ TDO Output Data Valid VM = Midpoint Voltage (NVDD/2) Output Data Valid Input Data Valid VM Figure 44. Test Access Port Timing Diagram M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 Freescale Semiconductor 55 I2C 15 I2C This section describes the DC and AC electrical characteristics for the I2C interface. 15.1 I2C DC Electrical Characteristics Table 43. I2C DC Electrical Characteristics Table 43 provides the DC electrical characteristics for the I2C interface. At recommended operating conditions with NVDD of 3.3 V ± 0.3 V. Parameter Input high-voltage level Input low-voltage level Low-level output voltage High-level output voltage Output fall time from VIH(min) to V IL(max) with a bus capacitance from 10 to 400 pF Pulse width of spikes which must be suppressed by the input filter Capacitance for each I/O pin Input current, (0 V ≤VIN ≤ NVDD) Symbol VIH VIL VOL VOH Min 0.7 × NV DD –0.3 0 0.8 x NVDD Max NVDD + 0.3 0.3 × NVDD 0.2 × NVDD NVDD + 0.3 250 50 10 ±5 Unit Notes V V V V ns ns pF μA — — 1 — 2 3 — — tI2KLKV 20 + 0.1 × CB tI2KHKL CI IIN 0 — — Notes: 1. Output voltage (open drain or open collector) condition = 3 mA sink current. 2. C B = capacitance of one bus line in pF. 3. For information on the digital filter used, see the M PC8308 PowerQUICC II Pro Processor Reference Manual. 15.2 I2C AC Electrical Specifications Table 44. I2C AC Electrical Specifications Table 44 provides the AC timing parameters for the I2C interface. All values refer to VIH (min) and V IL (max) levels (see Table 43). Parameter SCL clock frequency Low period of the SCL clock High period of the SCL clock Setup time for a repeated START condition Hold time (repeated) START condition (after this period, the first clock pulse is generated) Data setup time Data hold time: I2C bus devices Fall time of both SDA and SCL signals5 Symbol1 fI2C tI2CL tI2CH tI2SVKH tI2SXKL tI2DVKH tI2DXKL Min 0 1.3 0.6 0.6 0.6 100 — 02 Max 400 — — — — — — 0.9 3 300 Unit kHz μs μs μs μs ns μs tI2CF — ns M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 56 Freescale Semiconductor I2C Table 44. I2C AC Electrical Specifications (continued) All values refer to VIH (min) and V IL (max) levels (see Table 43). Parameter Setup time for STOP condition Bus free time between a STOP and START condition Noise margin at the LOW level for each connected device (including hysteresis) Noise margin at the HIGH level for each connected device (including hysteresis) Symbol1 tI2PVKH tI2KHDX VNL VNH Min 0.6 1.3 0.1 × NVDD 0.2 × NVDD Max — — — — Unit μs μs V V Notes: 1. The symbols used for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tI2DVKH symbolizes I2C timing (I2) with respect to the time data input signals (D) reach the valid state (V) relative to the tI2C clock reference (K) going to the high (H) state or setup time. Also, tI2SXKL symbolizes I2C timing (I2) for the time that the data with respect to the start condition (S) went invalid (X) relative to the tI2C clock reference (K) going to the low (L) state or hold time. Also, tI2PVKH symbolizes I2C timing (I2) for the time that the data with respect to the stop condition (P) reaching the valid state (V) relative to the tI2C clock reference (K) going to the high (H) state or setup time. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall). 2. The device provides a hold time of at least 300 ns for the SDA signal (referred to the VIHmin of the SCL signal) to bridge the undefined region of the falling edge of SCL. 3. The maximum tI2DXKL has only to be met if the device does not stretch the low period (tI2CL) of the SCL signal. 4. CB = capacitance of one bus line in pF. 5. The device does not follow the I2C-BUS Specifications, Version 2.1, regarding the tI2CF AC parameter. Figure 45 provides the AC test load for the I2C. Output Z0 = 50 Ω RL = 5 0 Ω NVDD/2 Figure 45. I2C AC Test Load Figure 46 shows the AC timing diagram for the I2C bus. SDA tI2CF tI2CL SCL tI2SXKL S tI2DXKL tI2CH Sr tI2SVKH tI2PVKH P S tI2DVKH tI2SXKL tI2KHKL tI2CR tI2CF Figure 46. I2C Bus AC Timing Diagram M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 Freescale Semiconductor 57 Timers 16 Timers This section describes the DC and AC electrical specifications for the timers. 16.1 Timers DC Electrical Characteristics Table 45 provides the DC electrical characteristics for the MPC8308 timers pins, including TIN, TOUT, and TGATE. Table 45. Timers DC Electrical Characteristics Characteristic Output high voltage Output low voltage Output low voltage Input high voltage Input low voltage Input current Symbol VOH VOL VOL VIH VIL IIN Condition IOH = –8.0 mA IOL = 8.0 mA IOL = 3.2 mA — — 0 V ≤ VIN ≤ NVDD Min 2.4 — — 2.1 –0.3 — Max — 0.5 0.4 NVDD + 0.3 0.8 ±5 Unit V V V V V μA 16.2 Timers AC Timing Specifications Table 46. Timers Input AC Timing Specifications Characteristic Symbol1 tTIWID Min 20 Unit ns Table 46 provides the Timers input and output AC timing specifications. Timers inputs—minimum pulse width Notes: 1. Timers inputs and outputs are asynchronous to any visible clock. Timers outputs should be synchronized before use by any external synchronous logic. Timers inputs are required to be valid for at least tTIWID ns to ensure proper operation Figure 47 provides the AC test load for the Timers. Output Z0 = 50 Ω RL = 5 0 Ω NVDD/2 Figure 47. Timers AC Test Load M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 58 Freescale Semiconductor GPIO 17 GPIO This section describes the DC and AC electrical specifications for the GPIO of MPC8308 17.1 GPIO DC Electrical Characteristics Table 47. GPIO DC Electrical Characteristic Characteristic Output high voltage Output low voltage Output low voltage Input high voltage Input low voltage Input current Symbol VOH VOL VOL VIH VIL IIN Condition IOH = –8.0 mA IOL = 8.0 mA IOL = 3.2 mA — — 0 V ≤ VIN ≤ NVDD Min 2.4 — — 2.1 –0.3 — Max — 0.5 0.4 NVDD + 0.3 0.8 ±5 Unit V V V V V μA Table 47 provides the DC electrical characteristics for the GPIO. 17.2 GPIO AC Timing Specifications Table 48. GPIO Input AC Timing Specifications Characteristic GPIO inputs—minimum pulse width Symbol1 tPIWID Min 20 Unit ns Table 48 provides the GPIO input and output AC timing specifications. Notes: 1. GPIO inputs and outputs are asynchronous to any visible clock. GPIO outputs should be synchronized before use by any external synchronous logic. GPIO inputs are required to be valid for at least tPIWID ns to ensure proper operation. Figure 48 provides the AC test load for the GPIO. Output Z0 = 50 Ω RL = 5 0 Ω NVDD/2 Figure 48. GPIO AC Test Load M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 Freescale Semiconductor 59 IPIC 18 IPIC This section describes the DC and AC electrical specifications for the external interrupt pins. 18.1 IPIC DC Electrical Characteristics Table 49. IPIC DC Electrical Characteristics Characteristic Input high voltage Input low voltage Input current Output high voltage Output low voltage Output low voltage Symbol VIH VIL IIN VOH VOL VOL Condition — — — IOH = –8.0 mA IOL = 8.0 mA IOL = 3.2 mA Min 2.1 –0.3 — 2.4 — — Max NVDD + 0.3 0.8 ±5 — 0.5 0.4 Unit V V μA V V V Table 49 provides the DC electrical characteristics for the external interrupt pins. 18.2 IPIC AC Timing Specifications Table 50. IPIC Input AC Timing Specifications Characteristic IPIC inputs—minimum pulse width Symbol1 tPIWID Min 20 Unit ns Table 50 provides the IPIC input and output AC timing specifications. Notes: 1. IPIC inputs and outputs are asynchronous to any visible clock. IPIC outputs should be synchronized before use by any external synchronous logic. IPIC inputs are required to be valid for at least tPIWID ns to ensure proper operation when working in edge triggered mode. 19 SPI This section describes the DC and AC electrical specifications for the SPI of the device. 19.1 SPI DC Electrical Characteristics Table 51. SPI DC Electrical Characteristics Characteristic Input high voltage Input low voltage Input current Symbol VIH VIL IIN Condition — — 0 V ≤ VIN ≤ NVDD Min 2.1 –0.3 — Max NVDD + 0.3 0.8 ±5 Unit V V μA Table 51 provides the DC electrical characteristics for the MPC8308 SPI. M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 60 Freescale Semiconductor SPI Table 51. SPI DC Electrical Characteristics (continued) Characteristic Output high voltage Output low voltage Output low voltage Symbol VOH VOL VOL Condition IOH = –8.0 mA IOL = 8.0 mA IOL = 3.2 mA Min 2.4 — — Max — 0.5 0.4 Unit V V V 19.2 SPI AC Timing Specifications Table 52. SPI AC Timing Specifications 1 Characteristic Symbol 2 tNIKHOV tNIKHOX tNEKHOV tNEKHOX tNIIVKH tNIIXKH tNEIVKH tNEIXKH 2 6 0 4 2 Min — 0.5 Max 6 — 8.5 — — — — — Unit ns ns ns ns ns ns ns ns Table 52 provides the SPI input and output AC timing specifications. SPI outputs valid—master mode (internal clock) delay SPI outputs hold—master mode (internal clock) delay SPI outputs valid—slave mode (external clock) delay SPI outputs hold—slave mode (external clock) delay SPI inputs—master mode (internal clock) input setup time SPI inputs—master mode (internal clock) input hold time SPI inputs—slave mode (external clock) input setup time SPI inputs—slave mode (external clock) input hold time Notes: 1. Output specifications are measured from the 50% level of the rising edge of SPICLK to the 50% level of the signal. Timings are measured at the pin. 2. The symbols used for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state)(reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tNIKHOX symbolizes the internal timing (NI) for the time SPICLK clock reference (K) goes to the high state (H) until outputs (O) are invalid (X). Figure 49 provides the AC test load for the SPI. Output Z0 = 50 Ω RL = 5 0 Ω NVDD/2 Figure 49. SPI AC Test Load Figure 50 and Figure 51 represent the AC timing from Table 52. Note that although the specifications generally reference the rising edge of the clock, these AC timing diagrams also apply when the falling edge is the active edge. M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 Freescale Semiconductor 61 Package and Pin Listings Figure 50 shows the SPI timing in slave mode (external clock). SPICLK (input) tNEIVKH tNEIXKH Input Signals: SPIMOSI (See Note) Output Signals: SPIMISO (See Note) tNEKHOV Note: The clock edge is selectable on SPI. Figure 50. SPI AC Timing in Slave Mode (External Clock) Diagram Figure 51 shows the SPI timing in master mode (internal clock). SPICLK (output) tNIIVKH tNIIXKH Input Signals: SPIMISO (See Note) Output Signals: SPIMOSI (See Note) tNIKHOV Note: The clock edge is selectable on SPI. Figure 51. SPI AC Timing in Master Mode (Internal Clock) Diagram 20 Package and Pin Listings This section details package parameters, pin assignments, and dimensions. The MPC8308 is available in a Moulded Array Process Ball Grid Array (MAPBGA). For information on the MAPBGA, see Section 20.1, “Package Parameters for the MPC8308 MAPBGA,” and Section 20.2, “Mechanical Dimensions of the MPC8308 MAPBGA.” 20.1 Package Parameters for the MPC8308 MAPBGA The package parameters are as provided in the following list. The package type is 19 mm × 19 mm, 473 MAPBGA. Package outline 19 mm × 19 mm Interconnects 473 Pitch 0.80 mm Module height (typical) 1.39 mm Solder Balls 96.5 Sn/ 3.5Ag Ball diameter (typical) 0.40 mm M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 62 Freescale Semiconductor Package and Pin Listings 20.2 Mechanical Dimensions of the MPC8308 MAPBGA Figure 52 shows the mechanical dimensions and bottom surface nomenclature of the MAPBGA package. Figure 52. Mechanical Dimension and Bottom Surface Nomenclature of the MPC8308 MAPBG Notes: 1. All dimensions are in millimeters. M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 Freescale Semiconductor 63 Package and Pin Listings 2. Dimensions and tolerances per ASME Y14.5M-1994. 3. Maximum solder ball diameter measured parallel to datum A. 4. Datum A, the seating plane, is determined by the spherical crowns of the solder balls. 20.3 Pinout Listings Table 53. MPC8308 Pinout Listing Signal Package Pin Number DDR Memory Controller Interface Pin Type Power Supply Notes Table 53 provides the pin-out listing for the MPC8308, MAPBGA package. MEMC_MDQ[0] MEMC_MDQ[1] MEMC_MDQ[2] MEMC_MDQ[3] MEMC_MDQ[4] MEMC_MDQ[5] MEMC_MDQ[6] MEMC_MDQ[7] MEMC_MDQ[8] MEMC_MDQ[9] MEMC_MDQ[10] MEMC_MDQ[11] MEMC_MDQ[12] MEMC_MDQ[13] MEMC_MDQ[14] MEMC_MDQ[15] MEMC_MDQ[16] MEMC_MDQ[17] MEMC_MDQ[18] MEMC_MDQ[19] MEMC_MDQ[20] MEMC_MDQ[21] MEMC_MDQ[22] MEMC_MDQ[23] MEMC_MDQ[24] MEMC_MDQ[25] MEMC_MDQ[26] V6 Y4 AB3 AA3 AA2 AA1 W4 Y2 W3 W1 Y1 W2 U4 U3 V4 U6 T3 T2 R4 R3 P4 N6 P2 P1 N4 N3 N2 I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O GVDDA GVDDA GVDDA GVDDA GVDDA GVDDA GVDDA GVDDA GVDDA GVDDA GVDDA GVDDA GVDDA GVDDA GVDDA GVDDA GVDDB GVDDB GVDDB GVDDB GVDDB GVDDB GVDDB GVDDB GVDDB GVDDB GVDDB — — — — — — — — — — — — — — — — — — — — — — — — — — — M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 64 Freescale Semiconductor Package and Pin Listings Table 53. MPC8308 Pinout Listing (continued) Signal MEMC_MDQ[27] MEMC_MDQ[28] MEMC_MDQ[29] MEMC_MDQ[30] MEMC_MDQ[31] MEMC_MDM[0] MEMC_MDM[1] MEMC_MDM[2] MEMC_MDM[3] MEMC_MDM[8] MEMC_MDQS[0] MEMC_MDQS[1] MEMC_MDQS[2] MEMC_MDQS[3] MEMC_MDQS[8] MEMC_MBA[0] MEMC_MBA[1] MEMC_MBA[2] MEMC_MA0 MEMC_MA1 MEMC_MA2 MEMC_MA3 MEMC_MA4 MEMC_MA5 MEMC_MA6 MEMC_MA7 MEMC_MA8 MEMC_MA9 MEMC_MA10 MEMC_MA11 MEMC_MA12 MEMC_MA13 MEMC_MWE MEMC_MRAS Package Pin Number M6 M2 M3 L2 L3 AB2 V3 P3 M7 K2 AC3 V1 R1 M1 K1 C3 B2 H4 C2 D2 D3 D4 E4 F4 E2 E1 F2 F3 C1 F7 G2 G3 D5 B4 Pin Type I/O I/O I/O I/O I/O O O O O O I/O I/O I/O I/O I/O O O O O O O O O O O O O O O O O O O O Power Supply GVDDB GVDDB GVDDB GVDDB GVDDB GVDDA GVDDA GVDDB GVDDB GVDDB GVDDA GVDDA GVDDB GVDDB GVDDB GVDDB GVDDB GVDDB GVDDB GVDDB GVDDB GVDDB GVDDB GVDDB GVDDB GVDDB GVDDB GVDDB GVDDB GVDDB GVDDB GVDDB GVDDB GVDDB Notes — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 Freescale Semiconductor 65 Package and Pin Listings Table 53. MPC8308 Pinout Listing (continued) Signal MEMC_MCAS MEMC_MCS[0] MEMC_MCS[1] MEMC_MCKE MEMC_MCK [0] MEMC_MCK [1] MEMC_MCK [2] MEMC_MCK [0] MEMC_MCK [1] MEMC_MCK [2] MEMC_MODT[0] MEMC_MODT[1] MEMC_MECC[0] MEMC_MECC[1] MEMC_MECC[2] MEMC_MECC[3] MEMC_MECC[4] MEMC_MECC[5] MEMC_MECC[6] MEMC_MECC[7] MVREF Package Pin Number C5 B6 C6 H3 A3 U2 G1 A4 U1 H1 A5 B5 L4 L6 K4 K3 J2 K6 J3 J6 G6 Local Bus Controller Interface LD0 LD1 LD2 LD3 LD4 LD5 LD6 LD7 LD8 LD9 LD10 U18 V18 U16 Y20 AA21 AC22 V17 AB21 Y19 AA20 Y17 I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O NVDDP_K NVDDP_K NVDDP_K NVDDP_K NVDDP_K NVDDP_K NVDDP_K NVDDP_K NVDDP_K NVDDP_K NVDDP_K 8 8 8 8 8 8 8 8 8 8 8 Pin Type O O O O O O O O O O O O I/O I/O I/O I/O I/O I/O I/O I/O I Power Supply GVDDB GVDDB GVDDB GVDDB GVDDB GVDDB GVDDB GVDDB GVDDB GVDDB GVDDB GVDDB GVDDB GVDDB GVDDB GVDDB GVDDB GVDDB GVDDB GVDDB GVDDB Notes — — — 3 — — — — — — — — — — — — — — — — — M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 66 Freescale Semiconductor Package and Pin Listings Table 53. MPC8308 Pinout Listing (continued) Signal LD11 LD12 LD13 LD14 LD15 LA0 LA1 LA2 LA3 LA4 LA5 LA6 LA7 LA8 LA9 LA10 LA11 LA12 LA13 LA14 LA15 LA16 LA17 LA18 LA19 LA20 LA21 LA22 LA23 LA24 LA25 LCS [0] LCS [1] LCS [2] Package Pin Number AC21 AB20 V16 AA19 AC17 AC20 Y16 U15 V15 AA18 AA17 AC19 AA16 AB18 AC18 V14 AB17 AA15 AC16 Y14 AC15 U13 V13 Y13 AB15 AA14 AB14 U12 V12 Y12 AC14 AA13 AB13 AA12 Pin Type I/O I/O I/O I/O I/O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O Power Supply NVDDP_K NVDDP_K NVDDP_K NVDDP_K NVDDP_K NVDDP_K NVDDP_K NVDDP_K NVDDP_K NVDDP_K NVDDP_K NVDDP_K NVDDP_K NVDDP_K NVDDP_K NVDDP_K NVDDP_K NVDDP_K NVDDP_K NVDDP_K NVDDP_K NVDDP_K NVDDP_K NVDDP_K NVDDP_K NVDDP_K NVDDP_K NVDDP_K NVDDP_K NVDDP_K NVDDP_K NVDDP_K NVDDP_K NVDDP_K Notes 8 8 8 8 8 — — — — — — — — — — — — — — — — — — — — — — — — — — 4 4 4 M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 Freescale Semiconductor 67 Package and Pin Listings Table 53. MPC8308 Pinout Listing (continued) Signal LCS [3] LWE[0] /LFWE0/LBS0 LWE[1]/LBS1 LBCTL LGPL0/LFCLE LGPL1/LFALE LGPL2/LOE /LFRE LGPL3/LFWP LGPL4/LGTA/LUPWAIT/LFRB LGPL5 LCLK0 DUART UART_SOUT1/MSRCID0/LSRCID0 UART_SIN1/MSRCID1/LSRCID1 UART_SOUT2/MSRCID2/LSRCID2 UART_SIN2/MSRCID3/LSRCID3 PEX PHY TXA TXA RXA RXA SD_IMP_CAL_RX SD_REF_CLK SD_REF_CLK SD_PLL_TPD SD_IMP_CAL_TX SD_PLL_TPA_ANA SDAVDD_0 SDAVSS_0 I2C interface IIC_SDA1 IIC_SCL1 C9 A9 I/O I/O NVDDA NVDDA 2 2 C14 C15 A13 B13 A15 C12 D12 F13 A11 F11 G12 F12 O O I I I I I O I O I I XPADVDD XPADVDD XCOREVDD XCOREVDD XCOREVDD XCOREVDD XCOREVDD — XPADVDD — — — — — — — — — — — — — — — C17 B18 D17 D18 O I/O O I/O NVDDB NVDDB NVDDB NVDDB — — — — Package Pin Number Y11 AB11 AC11 U11 Y10 AA10 AB10 AC10 AB9 Y9 AC12 Pin Type O O O O O O O O I/O O O Power Supply NVDDP_K NVDDP_K NVDDP_K NVDDP_K NVDDP_K NVDDP_K NVDDP_K NVDDP_K NVDDP_K NVDDP_K NVDDP_K Notes 4 — — — — — 4 — 4 — — M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 68 Freescale Semiconductor Package and Pin Listings Table 53. MPC8308 Pinout Listing (continued) Signal IIC_SDA2/CKSTOP_OUT IIC_SCL2/CKSTOP_IN Interrupts IRQ[0]/MCP_IN IRQ[1]/MCP_OUT IRQ[2] /CKSTOP_OUT IRQ[3] /CKSTOP_IN JTAG TCK TDI TDO TMS TRST TEST TEST_MODE System Control HRESET PORESET SRESET Clocks SYS_CLK_IN RTC_PIT_CLOCK MISC QUIESCE THERM0 ETSEC1 TSEC1_COL TSEC1_CRS TSEC1_GTX_CLK TSEC1_RX_CLK TSEC1_RX_DV TSEC1_RXD[3] B20 B21 F18 A22 D21 C22 I I O I I I NVDDC NVDDC NVDDC NVDDC NVDDC NVDDC — — 3 — — — AA7 AC7 O I NVDDP_K NVDDP_K — 6 AC8 AA23 I I NVDDP_K NVDDJ — — AA9 AA8 AB7 I/O I I/O NVDDP_K NVDDP_K NVDDP_K 1 — — AC6 I NVDDP_K 5 Y7 U9 AC5 AA6 V8 I I O I I NVDDP_K NVDDP_K NVDDP_K NVDDP_K NVDDP_K — 4 3 4 4 A17 F16 B17 A18 I I/O I/O I NVDDB NVDDB NVDDB NVDDB — — — — Package Pin Number D10 C10 Pin Type I/O I/O Power Supply NVDDA NVDDA Notes 2 2 M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 Freescale Semiconductor 69 Package and Pin Listings Table 53. MPC8308 Pinout Listing (continued) Signal TSEC1_RXD[2] TSEC1_RXD[1] TSEC1_RXD[0] TSEC1_RX_ER TSEC1_TX_CLK/TSEC1_GTX_CLK125 TSEC1_TXD[3]/CFG_RESET_SOURCE[0] TSEC1_TXD[2]/CFG_RESET_SOURCE[1] TSEC1_TXD[1]/CFG_RESET_SOURCE[2] TSEC1_TXD[0]/CFG_RESET_SOURCE[3] TSEC1_TX_EN/LBC_PM_REF_10 TSEC1_TX_ER/LB_POR_CFG_BOOT_ECC Ethernet Mgmt TSEC1_MDC TSEC1_MDIO eSDHC/GTM SD_CLK/GPIO_16 SD_CMD/GPIO_17 SD_CD /GTM1_TIN1/GPIO_18 SD_WP/GTM1_TGATE1/GPIO_19 SD_DAT[0]/GTM1_TOUT1/GPIO_20 SD_DAT[1]/GTM1_TOUT2/GPIO_21 SD_DAT[2]/GTM1_TIN2/GPIO_22 SD_DAT[3]/GTM1_TGATE2/GPIO_23 SPI SPIMOSI/MSRCID4/LSRCID4 SPIMISO/MDVAL/LDVAL SPICLK SPISEL GPIO/ETSEC2 GPIO[0]/TSEC2_COL GPIO[1]/TSEC2_TX_ER GPIO[2]/TSEC2_GTX_CLK GPIO[3]/TSEC2_RX_CLK G21 K23 H18 G23 I/O I/O I/O I/O NVDDF NVDDF NVDDF NVDDF — — — — AB5 Y6 AA5 AB4 I/O I/O I/O I NVDDP_K NVDDP_K NVDDP_K NVDDP_K — — — — D7 G9 A7 D8 C8 B8 A8 B9 O I/O I I I/O I/O I/O I/O NVDDA NVDDA NVDDA NVDDA NVDDA NVDDA NVDDA NVDDA — — — — — — — — A20 C19 O I/O NVDDB NVDDB — 2 Package Pin Number C21 C20 D20 C23 E23 F22 F21 E21 D22 F20 E22 Pin Type I I I I I I/O I/O I/O I/O O I/O Power Supply NVDDC NVDDC NVDDC NVDDC NVDDC NVDDC NVDDC NVDDC NVDDC NVDDC NVDDC Notes — — — — — — — — — — 7 M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 70 Freescale Semiconductor Package and Pin Listings Table 53. MPC8308 Pinout Listing (continued) Signal GPIO[4]/TSEC2_RX_DV GPIO[5]/TSEC2_RXD3 GPIO[6]/TSEC2_RXD2 GPIO[7]/TSEC2_RXD1 GPIO[8]/TSEC2_RXD0 GPIO[9]/TSEC2_RX_ER GPIO[10]/TSEC2_TX_CLK/TSEC2_GTX_CLK125 GPIO[11]/TSEC2_TXD3 GPIO[12]/TSEC2_TXD2 GPIO[13]/TSEC2_TXD1 GPIO[14]/TSEC2_TXD0 GPIO[15]/TSEC2_TX_EN Package Pin Number J18 J20 H22 H21 H20 J21 J23 K22 K20 K18 J17 K21 USB/IEEE1588/GTM USBDR_PWR_FAULT USBDR_CLK USBDR_DIR USBDR_NXT USBDR_TXDRXD0 USBDR_TXDRXD1 USBDR_TXDRXD2 USBDR_TXDRXD3 USBDR_TXDRXD4 USBDR_TXDRXD5 USBDR_TXDRXD6 USBDR_TXDRXD7 USBDR_PCTL0 USBDR_PCTL1 USBDR_STP TSEC_TMR_CLK/ GPIO[8] GTM1_TOUT3/ G PIO[9] GTM1_TOUT4/ G PIO[10] TSEC_TMR_TRIG1/ GPIO[11] TSEC_TMR_TRIG2/ GPIO[12] TSEC_TMR_GCLK P20 R23 R21 P18 T22 T21 U23 U22 T20 R18 V23 V22 R17 U20 V21 W23 T18 V20 W21 Y21 L17 I I I I I/O I/O I/O I/O I/O I/O I/O I/O O O O I O O I I O NVDDH NVDDH NVDDH NVDDH NVDDH NVDDH NVDDH NVDDH NVDDH NVDDH NVDDH NVDDH NVDDH NVDDH NVDDH NVDDH NVDDH NVDDH NVDDH NVDDH NVDDG — — — — — — — — — — — — — — — — — — — — — Pin Type I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O Power Supply NVDDF NVDDF NVDDF NVDDF NVDDF NVDDF NVDDF NVDDF NVDDF NVDDF NVDDF NVDDF Notes — — — — — — — — — — — — M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 Freescale Semiconductor 71 Package and Pin Listings Table 53. MPC8308 Pinout Listing (continued) Signal TSEC_TMR_PP1 TSEC_TMR_PP2 TSEC_TMR_PP3/ GPIO[13] TSEC_TMR_ALARM1 TSEC_TMR_ALARM2/ GPIO[14] GPIO[7] TSEC2_CRS TSEC2_TMR_RX_ESFD/ GPIO[1] TSEC2_TMR_TX_ESFD/GPIO[2] TSEC1_TMR_RX_ESFD/GPIO[3] TSEC1_TMR_TX_ESFD/ GPIO[4] GTM1_TGATE3 GTM1_TIN4 GTM1_TGATE4/ G PIO[15] GTM1_TIN3 GPIO[5] GPIO[6] Package Pin Number L18 L21 L22 L23 M23 M22 M21 M18 M20 N23 N21 N20 N18 P23 P22 N17 P21 Power and Ground Supplies AVDD1 AVDD2 NC, No Connection VDD R6 V10 Y23, B11, B16, D16 H8, H9, H10, H14, H15, H16, J8, J16, K8, K16, L8, L16, M8, M16, N8, N16, P8, P16, R8, R16, T8, T9, T10, T11, T12, T13, T14, T15, T16 I I — I — — — — — — — — Pin Type O O O O O O O O O O O I I I I I I Power Supply NVDDG NVDDG NVDDG NVDDG NVDDG — NVDDG NVDDG NVDDG NVDDG NVDDG NVDDG NVDDG NVDDG NVDDG NVDDH NVDDH Notes — — — — — — — — — — — — — — — — — M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 72 Freescale Semiconductor Package and Pin Listings Table 53. MPC8308 Pinout Listing (continued) Signal VSS Package Pin Number A2, A21, B1, B19, B23, C4, C16, D6, D19, E3, F8, F15, F17, F23, G7, G8, G10, G15, G16, G17, G20, H2, H6, H7, H17, H23, J7, J9, J10, J11, J12, J13, J14, J15, K9, K10, K11, K12, K13, K14, K15, L1, L7, L9, L10, L11, L12, L13, L14, L15, L20, M4, M9, M10, M11, M12, M13, M14, M15, N9, N10, N11, N12, N13, N14, N15, P6, P7, P9, P10, P11, P12, P13, P14, P15, R2, R7, R9, R10, R11, R12, R13, R14, R15, R22, T6, T7, U8, U17, U21, V2, V7, V9, V11, W20, Y8, Y15, AA4, AB1, AB6, AB12, AB19, AC2, AC9, AC23 B7, B10, C7, D9, F9 A16, A19, C18 A23, B22, D23, E20, G18 G22, J22, K17 M17, N22 P17, R20, T17, T23, W22, Y22 AB23, AA22 U10, U14, Y5, Y18, AA11, AB8, AB16, AB22, AC4, AC13 A1, A6, B3, D1, F1, F6, G4, J1, J4, K7, N1, N7, T1, T4, U7, Y3, AC1 D15, F10, F14 A10, B15, D14, G13, G14, H12 Pin Type I Power Supply — Notes — NVDDA NVDDB NVDDC NVDDF NVDDG NVDDH NVDDJ NVDDP_K I I I I I I I I — — — — — — — — — — — — — — — — GVDD I — — XPADVDD XPADVSS I I — — — — M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 Freescale Semiconductor 73 Package and Pin Listings Table 53. MPC8308 Pinout Listing (continued) Signal XCOREVDD XCOREVSS Package Pin Number A14, B12, C13 A12, B14, C11, D11, D13, G11, H11, H13 Pin Type I I Power Supply — — Notes — — Notes: 1. This pin is an open drain signal. A weak pull-up resistor (1 kΩ) should be placed on this pin to NVDD 2. This pin is an open drain signal. A weak pull-up resistor (2–10 kΩ) should be placed on this pin to NV DD. 3. This output is actively driven during reset rather than being three-stated during reset. 4. This pin has weak internal pull-up that is always enabled. 5. This pin must always be tied to VSS. 6. Internal thermally sensitive resistor, resistor value varies linearly with temperature. Useful for determining the junction temperature. 7. The LB_POR_CFG_BOOT_ECC is sampled only during the PORESET negation. This pin with an internal pull down resistor enables the ECC by default. To disable the ECC an external strong pull up resistor or a buffer released to high impedance is needed. 8. This pin has weak internal pull-down that is always enabled M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 74 Freescale Semiconductor Clocking 21 Clocking Figure 53 shows the internal distribution of clocks within the device. MPC8308 e300 Core x M1 e300 PLL csb_clk clk tree x L2 System PLL ref 24–66 MHz SYS_CLK_IN fb Clk Gen ddr_clk lbc_clk DDR Clock Divider /2 /n LBC Clock Divider MCK[0:2] MCK[0:2] DDR Memory Device Local Bus Memory Device SD_CLK eSHDC PCI Express Protocol Converter eTSEC1 TSEC1_RX_CLK PCVTR Mux SD_REF_CLK SD_REF_CLK_B 125/100 MHz 1 2 + - PLL SerDes PHY TSEC1_TX_CLK/ TSEC1_GTX_CLK125 Multiplication factor M = 1, 1.5, 2, 2.5, and 3. Value is decided by RCWLR[COREPLL]. Multiplication factor L = 2, 3, 4, 5 and 6. Value is decided by RCWLR[SPMF]. Figure 53. MPC8308 Clock Subsystem The following external clock sources are utilized on the MPC8308: • System clock (SYS_CLK_IN) • Ethernet Clock (TSEC1_RX_CLK/TSEC1_TX_CLK/TSEC1_GTX_CLK125 for eTSEC) • SerDes PHY clock • eSHDC clock (SD_CLK) For more information, see the SerDes chapter in the MPC8308 PowerQUICC II Pro Processor Reference Manual. All clock inputs can be supplied using an external canned oscillator, a clock generation chip, or some other source that provides a standard CMOS square wave input. M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 Freescale Semiconductor 75 Clocking 21.1 System Clock Domains The primary clock input (SYS_CLK_IN) frequency is multiplied up by the system phase-locked loop (PLL) and the clock unit to create three major clock domains: • The coherent system bus clock (csb_clk) • The internal clock for the DDR controller (ddr_clk) • The internal clock for the local bus interface unit (lbc_clk) The csb_clk frequency is derived as follows: csb_clk = [SYS_CLK_IN] × SPMF The csb_clk serves as the clock input to the e300 core. A second PLL inside the core multiplies up the csb_clk frequency to create the internal clock for the core (core_clk). The system and core PLL multipliers are selected by the SPMF and COREPLL fields in the reset configuration word low (RCWL), which is loaded at power-on reset or by one of the hard-coded reset options. For more information, see the Reset Clock Configuration chapter in the MPC8308 PowerQUICC II Pro Processor Reference Manual. The DDR SDRAM memory controller operates with a frequency equal to twice the frequency of csb_clk. Note that ddr_clk is not the external memory bus frequency; ddr_clk passes through the DDR clock divider (÷2) to create the differential DDR memory bus clock outputs (MCK and MCK). However, the data rate is the same frequency as ddr_clk. The local bus memory controller operates with a frequency equal to the frequency of csb_clk. Note that lbc_clk is not the external local bus frequency; lbc_clk passes through the LBC clock divider to create the external local bus clock outputs (LSYNC_OUT and LCLK0:2). The LBC clock divider ratio is controlled by LCCR[CLKDIV]. For more information, see the Reset Clock Configuration chapter in the MPC8308 PowerQUICC II Pro Processor Reference Manual. In addition, some of the internal units may be required to be shut off or operate at lower frequency than the csb_clk frequency. These units have a default clock ratio that can be configured by a memory-mapped register after the device comes out of reset. Table 54 specifies which units have a configurable clock frequency. For more information, see Reset Clock Configuration chapter in the MPC8308 PowerQUICC II Pro Processor Reference Manual. Table 54. Configurable Clock Units Unit eTSEC1,eTSEC2 I2C DMA complex PCIEXP eSDHC USB Default Frequency Options Off, csb_clk, csb_clk/2, csb_clk/3 Off, csb_clk,csb_clk/2, csb_clk/3 Off, csb_clk,csb_clk/2,csb_clk/3 Off, csb_clk, csb_clk/2, csb_clk/3 Off, csb_clk, csb_clk/2, csb_clk/3 Off, csb_clk, csb_clk/2, csb_clk/3 csb_clk/3 csb_clk csb_clk csb_clk csb_clk csb_clk NOTE The clock ratios of these units must be set before they are accessed. M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 76 Freescale Semiconductor Clocking Table 55 provides the operating frequencies for the device under recommended operating conditions (Table 2). Table 55. Operating Frequencies for MPC8308 Characteristic1 e300 core frequency (core_clk) Coherent system bus frequency (csb_clk) DDR2 memory bus frequency (MCK)2 Local bus frequency (LCLK0)3 Maximum Operating Frequency 400 133 133 66 Unit MHz MHz MHz MHz Notes: 1. The SYS_CLK_IN frequency, RCWL[SPMF], and RCWL[COREPLL] settings must be chosen such that the resulting csb_clk, MCK, LCLK0, and core_clk frequencies do not exceed their respective maximum or minimum operating frequencies. 2. The DDR data rate is 2x the DDR memory bus frequency. 3. The local bus frequency is 1/2, 1/4, or 1/8 of the lbc_clk frequency (depending on LCCR[CLKDIV]) which is in turn, 1x or 2x the csb_clk frequency (depending on RCWL[LBCM]). 21.2 System PLL Configuration The system PLL is controlled by the RCWL[SPMF] parameter. Table 56 shows the multiplication factor encodings for the system PLL. Table 56. System PLL Ratio RCWL[SPMF] 0000 0001 0010 0011 0100 0101 0110–1111 csb_clk : SYS_CLK_IN Reserved Reserved 2:1 3:1 4:1 5:1 Reserved As described in Section 21, “Clocking,” the LBCM, DDRCM, and SPMF parameters in the reset configuration word low select the ratio between the primary clock input (SYS_CLK_IN) and the internal M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 Freescale Semiconductor 77 Clocking coherent system bus clock (csb_clk). Table 57 shows the expected frequency values for the CSB frequency for select csb_clk to SYS_CLK_IN ratios. Table 57. CSB Frequency Options Input Clock Frequency (MHz) SPMF csb_clk :Input Clock Ratio 25 0010 0100 0101 2:1 4:1 5:1 125 133 33.33 66.67 133 21.3 Core PLL Configuration RCWL[COREPLL] selects the ratio between the internal coherent system bus clock (csb_clk) and the e300 core clock (core_clk). Table 58 shows the encodings for RCWL[COREPLL]. COREPLL values that are not listed in Table 58 should be considered as reserved. NOTE Core VCO frequency = core frequency × VCO divider. The VCO divider, which is determined by RCWLR[COREPLL], must be set properly so that the core VCO frequency is in the range of 400–800 MHz. Table 58. e300 Core PLL Configuration RCWL[COREPLL] core_clk: csb_clk Ratio1 0–1 2–5 0000 6 0 n 0 0 0 1 1 1 0 0 0 1 1 PLL bypassed (PLL off, csb_clk clocks core directly) n/a 1:1 1:1 1:1 1.5:1 1.5:1 1.5:1 2:1 2:1 2:1 2.5:1 2.5:1 VCO Divider (VCOD)2 nn 11 00 01 10 00 01 10 00 01 10 00 01 PLL bypassed (PLL off, csb_clk clocks core directly) n/a 2 4 8 2 4 8 2 4 8 2 4 nnnn 0001 0001 0001 0001 0001 0001 0010 0010 0010 0010 0010 M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 78 Freescale Semiconductor Thermal Table 58. e300 Core PLL Configuration (continued) RCWL[COREPLL] core_clk: csb_clk Ratio1 0–1 10 00 01 10 Notes: 1 2 VCO Divider (VCOD)2 2–5 0010 0011 0011 0011 6 1 0 0 0 2.5:1 3:1 3:1 3:1 8 2 4 8 For any core_clk:csb_clk ratios, the core_clk must not exceed its maximum operating frequency of 333 MHz. Core VCO frequency = core frequency × VCO divider. Note that VCO divider has to be set properly so that the core VCO frequency is in the range of 400–800 MHz. 22 Thermal This section describes the thermal specifications of the device. 22.1 Thermal Characteristics Table 59. Package Thermal Characteristics for MAPBGA Characteristic Board Type Single layer board (1s) Four layer board (2s2p) Single layer board (1s) Four layer board (2s2p) — — Natural Convection Symbol Value 42 27 35 24 17 9 2 Unit °C/W °C/W °C/W °C/W °C/W °C/W °C/W Notes 1,2 1,2,3 1,3 1,3 4 5 6 Table 59 provides the package thermal characteristics for the 473, 19 × 19 mm MAPBGA. Junction to Ambient Natural Convection Junction to Ambient Natural Convection Junction to Ambient (@200 ft/min) Junction to Ambient (@200 ft/min) Junction to Board Junction to Case Junction to Package Top RθJA RθJA RθJMA RθJMA RθJB RθJC ΨJT M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 Freescale Semiconductor 79 Thermal Table 59. Package Thermal Characteristics for MAPBGA (continued) Characteristic Board Type Symbol Value Unit Notes Notes: 1. Junction temperature is a function of die size, on-chip power dissipation, package thermal resistance, mounting site (board) temperature, ambient temperature, air flow, power dissipation of other components on the board, and board thermal resistance. 2. Per JEDEC JESD51-2 with the single layer board horizontal. Board meets JESD51-9 specification. 3. Per JEDEC JESD51-6 with the board horizontal. 4. Thermal resistance between the die and the printed circuit board per JEDEC JESD51-8. Board temperature is measured on the top surface of the board near the package. 5. Thermal resistance between the die and the case top surface as measured by the cold plate method (MIL SPEC-883 Method 1012.1). 6. Thermal characterization parameter indicating the temperature difference between package top and the junction temperature per JEDEC JESD51-2. When Greek letters are not available, the thermal characterization parameter is written as Psi-JT. 22.2 Thermal Management Information For the following sections, PD = (VDD × IDD) + PI/O, where PI/O is the power dissipation of the I/O drivers. 22.2.1 Estimation of Junction Temperature with Junction-to-Ambient Thermal Resistance An estimation of the chip junction temperature, TJ, can be obtained from the equation: TJ = TA + (RθJA × PD) where: TJ = junction temperature (°C) TA = ambient temperature for the package (°C) RθJA = junction-to-ambient thermal resistance (°C/W) PD = power dissipation in the package (W) The junction-to-ambient thermal resistance is an industry standard value that provides a quick and easy estimation of thermal performance. As a general statement, the value obtained on a single-layer board is appropriate for a tightly packed printed-circuit board. The value obtained on the board with the internal planes is usually appropriate if the board has low-power dissipation and the components are well separated. Test cases have demonstrated that errors of a factor of two (in the quantity TJ – TA) are possible. 22.2.2 Estimation of Junction Temperature with Junction-to-Board Thermal Resistance The thermal performance of a device cannot be adequately predicted from the junction-to-ambient thermal resistance. The thermal performance of any component is strongly dependent on the power dissipation of surrounding components. In addition, the ambient temperature varies widely within the application. For many natural convection and especially closed box applications, the board temperature at the perimeter (edge) of the package is approximately the same as the local air temperature near the device. Specifying M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 80 Freescale Semiconductor System Design Information the local ambient conditions explicitly as the board temperature provides a more precise description of the local ambient conditions that determine the temperature of the device. At a known board temperature, the junction temperature is estimated using the following equation: TJ = TB + (RθJB × PD) where: TJ = junction temperature (°C) TB = board temperature at the package perimeter (°C) RθJB = junction-to-board thermal resistance (°C/W) per JESD51–8 PD = power dissipation in the package (W) When the heat loss from the package case to the air can be ignored, acceptable predictions of junction temperature can be made. The application board should be similar to the thermal test condition: the component is soldered to a board with internal planes. 22.2.3 Experimental Determination of Junction Temperature To determine the junction temperature of the device in the application after prototypes are available, the thermal characterization parameter (ΨJT) can be used to determine the junction temperature with a measurement of the temperature at the top center of the package case using the following equation: TJ = TT + (ΨJT × PD) where: TJ = junction temperature (°C) TT = thermocouple temperature on top of package (°C) ΨJT = thermal characterization parameter (°C/W) PD = power dissipation in the package (W) The thermal characterization parameter is measured per JESD51-2 specification using a 40 gauge type T thermocouple epoxied to the top center of the package case. The thermocouple should be positioned so that the thermocouple junction rests on the package. A small amount of epoxy is placed over the thermocouple junction and over about 1 mm of wire extending from the junction. The thermocouple wire is placed flat against the package case to avoid measurement errors caused by cooling effects of the thermocouple wire. 23 System Design Information This section provides electrical and thermal design recommendations for successful application of the device M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 Freescale Semiconductor 81 System Design Information 23.1 System Clocking The device includes two PLLs. 1. The platform PLL generates the platform clock from the externally supplied SYS_CLK_IN input. The frequency ratio between the platform and SYS_CLK_IN is selected using the platform PLL ratio configuration bits as described in Section 21.2, “System PLL Configuration.” 2. The e300 core PLL generates the core clock as a slave to the platform clock. The frequency ratio between the e300 core clock and the platform clock is selected using the e300 PLL ratio configuration bits as described in Section 21.3, “Core PLL Configuration.” 23.2 PLL Power Supply Filtering Each of the PLLs listed above is provided with power through independent power supply pins (AVDD1 for core PLL and AVDD2 for the platform PLL). The AVDD level should always be equivalent to VDD, and preferably these voltages are derived directly from VDD through a low-pass filter scheme such as the following. There are a number of ways to reliably provide power to the PLLs, but the recommended solution is to provide independent filter circuits as illustrated in Figure 54, one to each of the two AVDD pins. By providing independent filters to each PLL the opportunity to cause noise injection from one PLL to the other is reduced. This circuit is intended to filter noise in the PLLs’ resonant frequency range from a 500 kHz to 10 MHz range. It should be built with surface mount capacitors with minimum effective series inductance (ESL). Consistent with the recommendations of Dr. Howard Johnson in High Speed Digital Design: A Handbook of Black Magic (Prentice Hall, 1993), multiple small capacitors of equal value are recommended over a single large value capacitor. Each circuit should be placed as close as possible to the specific AVDD pin being supplied to minimize noise coupled from nearby circuits. It should be possible to route directly from the capacitors to the AV DD pin, which is on the periphery of package, without the inductance of vias. Figure 54 shows the PLL power supply filter circuits. 10 Ω V DD 2.2 µF 2.2 µF Low ESL Surface Mount Capacitors AVDD1 and AVDD2 Figure 54. PLL Power Supply Filter Circuit 23.3 Decoupling Recommendations Due to large address and data buses and high-operating frequencies, the device can generate transient power surges and high-frequency noise in its power supply, especially while driving large capacitive loads. This noise must be prevented from reaching other components in the MPC8308 system, and the MPC8308 itself requires a clean, tightly regulated source of power. Therefore, it is recommended that the system designer place at least one decoupling capacitor at each VDD, NVDD, GVDD, and LVDD pin of the device. M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 82 Freescale Semiconductor System Design Information These decoupling capacitors should receive their power from separate VDD, NVDD, GVDD, LVDD, and VSS power planes in the PCB, utilizing short traces to minimize inductance. Capacitors may be placed directly under the device using a standard escape pattern. Others may surround the part. These capacitors should have a value of 0.01 or 0.1 µF. Only ceramic SMT (surface mount technology) capacitors should be used to minimize lead inductance, preferably 0402 or 0603 sizes. In addition, it is recommended that there be several bulk storage capacitors distributed around the PCB, feeding the VDD, NVDD, GVDD, LVDD planes, to enable quick recharging of the smaller chip capacitors. These bulk capacitors should have a low ESR (equivalent series resistance) rating to ensure the quick response time necessary. They should also be connected to the power and ground planes through two vias to minimize inductance. Suggested bulk capacitors are in the range of 100–330 µF (AVX TPS tantalum or Sanyo OSCON). However, customers should work directly with their power regulator vendor for best values and types of bulk capacitors. 23.4 Connection Recommendations To ensure reliable operation, it is highly recommended to connect unused inputs to an appropriate signal level. Unused active low inputs should be tied to NVDD, GVDD, and LVDD as required. Unused active high inputs should be connected to VSS. All NC (no-connect) signals must remain unconnected. Power and ground connections must be made to all external VDD, NVDD, AVDD1, AVDD2, GVDD, LVDD, and VSS pins of the device. 23.5 Output Buffer DC Impedance The device drivers are characterized over process, voltage, and temperature. For all buses, the driver is a push–pull single-ended driver type (open drain for I2C, MDIO, and HRESET). To measure Z0 for the single-ended drivers, an external resistor is connected from the chip pad to NVDD or VSS. Then, the value of each resistor is varied until the pad voltage is NVDD/2 (Figure 55). The output impedance is the average of two components: the resistances of the pull-up and pull-down devices. When data is held high, SW1 is closed (SW2 is open), and RP is trimmed until the voltage at the pad equals NVDD/2. RP then becomes the resistance of the pull-up devices. RP and RN are designed to be close to each other in value. Then, Z0 = (RP + RN)/2. M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 Freescale Semiconductor 83 System Design Information NVDD RN SW2 Data Pad SW1 RP VSS Figure 55. Driver Impedance Measurement The value of this resistance and the strength of the driver’s current source can be found by making two measurements. First, the output voltage is measured while driving logic 1 without an external differential termination resistor. The measured voltage is V1 = Rsource × Isource. Second, the output voltage is measured while driving logic 1 with an external precision differential termination resistor of value R term. The measured voltage is V2 = (1/(1/R1 + 1/R2)) × Isource. Solving for the output impedance gives Rsource = Rterm × (V1/V2 – 1). The drive current is then Isource = V1/Rsource. Table 60 summarizes the signal impedance targets. The driver impedance are targeted at minimum VDD, nominal NVDD, 105°C. Table 60. Impedance Characteristics Impedance RN RP Local Bus, Ethernet, DUART, Control, Configuration, Power Management 42 Target 42 Target DDR DRAM 20 Target 20 Target Symbol Z0 Z0 Unit Ω Ω Note: Nominal supply voltages. See Table 2, T j = 105° C. 23.6 Configuration Pin Muxing The device provides the user with power-on configuration options that can be set through the use of external pull-up or pull-down resistors of 4.7 KΩ on certain output pins (see customer-visible configuration pins). These pins are generally used as output-only pins in normal operation. While PORESET is asserted, these pins are treated as inputs. The value presented on these pins while PORESET is asserted is latched when PORESET deasserts, at which time the input receiver is disabled and the I/O circuit takes on its normal function. Careful board layout with stubless connections to these pull-up/pull-down resistors coupled with the large value of the pull-up/pull-down resistor should minimize the disruption of signal quality or speed for output pins thus configured. M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 84 Freescale Semiconductor Ordering Information 23.7 Pull-Up Resistor Requirements The device requires high-resistance pull-up resistors (10 kΩ is recommended) on open drain type pins including I2C, Ethernet management MDIO, HRESET and IPIC (integrated programmable interrupt controller). Correct operation of the JTAG interface requires configuration of a group of system control pins as demonstrated in Figure 56. Care must be taken to ensure that these pins are maintained at a valid deasserted state under normal operating conditions, because most have asynchronous behavior and spurious assertion that give unpredictable results. 24 Ordering Information This section presents ordering information for the devices discussed in this document, and it shows an example of how the parts are marked. Ordering information for the devices fully covered by this document is provided in Section 24.1, “Part Numbers Fully Addressed by This Document.” 24.1 Part Numbers Fully Addressed by This Document Table 61 provides the Freescale part numbering nomenclature for the MPC8308 family. Note that the individual part numbers correspond to a maximum processor core frequency. For available frequencies, contact your local Freescale sales office. In addition to the maximum processor core frequency, the part numbering scheme also includes the maximum effective DDR memory speed. Each part number also contains a revision code which refers to the die mask revision number. Table 61. Part Numbering Nomenclature MPC Product Code MPC nnnn Part Identifier 8308 C Temperature Range1 Blank = 0 to 105° C C = –40 to 105°C VM Package2 VM = Pb-free 473 MAPBGA AD e300 Core Frequency3 AD = 266 MHz AF = 333 MHz AG = 400MHz D DDR Frequency D = 266 MHz A Revision Level Contact local Freescale sales office Notes: 1. Contact local Freescale office on availability of parts with C temperature range. 2. See Section 20, “Package and Pin Listings,” for more information on available package types. 3. Processor core frequencies supported by parts addressed by this specification only. Not all parts described in this specification support all core frequencies. Additionally, parts addressed by Part Number Specifications may support other maximum core frequencies. M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 Freescale Semiconductor 85 Document Revision History 24.2 Part Marking Parts are marked as in the example shown in Figure 56. MPCnnnnCVMADDA core/platform MHZ ATWLYYWW CCCCC *MMMMM YWWLAZ PBGA Notes: ATWLYYWW is the traceability code. CCCCC is the country code. MMMMM is the mask number. YWWLAZ is the assembly traceability code. Figure 56. Freescale Part Marking for PBGA Devices Table 62 shows the SVR settings. Table 62. SVR Settings Device MPC8308 Package MAPBGA SVR 0x8101 _0110 Note: PVR = 8085_0020 for the device. 25 Document Revision History Table 63 provides a revision history for this hardware specification. Table 63. Document Revision History Revision Rev 1 Date 07/2010 Substantive Change(s) • In “Table 4,” TA = 105 replaced with TJ = 105 • In “Table 8,” fSYS_CLK_IN (Max) = 66 replaced with 66.67 and tSYS_CLK_IN (Min) = 15.15 replaced with 15 • In “Table 53,” TSEC1_TMR_RX_ESFD replaced with TSEC2_TMR_RX_ESFD TSEC1_TMR_TX_ESFD replaced with TSEC2_TMR_TX_ESFD TSEC0_TMR_RX_ESFD replaced with TSEC1_TMR_RX_ESFD TSEC0_TMR_TX_ESFD replaced with TSEC1_TMR_TX_ESFD • In “Table 56,” rows from 1000 to 1111 removed Initial release Rev 0 05/2010 M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 86 Freescale Semiconductor Document Revision History THIS PAGE INTENTIONALLY LEFT BLANK M PC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1 Freescale Semiconductor 87 How to Reach Us: Home Page: www.freescale.com Web Support: http://www.freescale.com/support USA/Europe or Locations Not Listed: Freescale Semiconductor, Inc. Technical Information Center, EL516 2100 East Elliot Road Tempe, Arizona 85284 1-800-521-6274 or +1-480-768-2130 www.freescale.com/support Europe, Middle East, and Africa: Freescale Halbleiter Deutschland GmbH Technical Information Center Schatzbogen 7 81829 Muenchen, Germany +44 1296 380 456 (English) +46 8 52200080 (English) +49 89 92103 559 (German) +33 1 69 35 48 48 (French) www.freescale.com/support Japan: Freescale Semiconductor Japan Ltd. Headquarters ARCO Tower 15F 1-8-1, Shimo-Meguro, Meguro-ku Tokyo 153-0064 Japan 0120 191014 or +81 3 5437 9125 support.japan@freescale.com Asia/Pacific: Freescale Semiconductor China Ltd. Exchange Building 23F No. 118 Jianguo Road Chaoyang District Beijing 100022 China +86 10 5879 8000 support.asia@freescale.com For Literature Requests Only: Freescale Semiconductor Literature Distribution Center 1-800 441-2447 or +1-303-675-2140 Fax: +1-303-675-2150 LDCForFreescaleSemiconductor @hibbertgroup.com Information in this document is provided solely to enable system and software implementers to use Freescale Semiconductor products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document. Freescale Semiconductor reserves the right to make changes without further notice to any products herein. Freescale Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Freescale Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Freescale Semiconductor does not convey any license under its patent rights nor the rights of others. Freescale Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Freescale Semiconductor product could create a situation where personal injury or death may occur. Should Buyer purchase or use Freescale Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Freescale Semiconductor was negligent regarding the design or manufacture of the part. Freescale, the Freescale logo, CodeWarrior, ColdFire, PowerQUICC, StarCore, and Symphony are trademarks of Freescale Semiconductor, Inc. Reg. U.S. Pat. & Tm. Off. CoreNet, QorIQ, QUICC Engine, and VortiQa are trademarks of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. The Power Architecture and Power.org word marks and the Power and Power.org logos and related marks are trademarks and service marks licensed by Power.org. IEEE 1588 and 1149.1 are registered trademarks of the Institute of Electrical and Electronics Engineers, Inc. (IEEE). This product is not endorsed or approved by the IEEE. © 2010 Freescale Semiconductor, Inc. Document Number: MPC8308EC Rev. 1 07/2010
MPC8308_101 价格&库存

很抱歉,暂时无法提供与“MPC8308_101”相匹配的价格&库存,您可以联系我们找货

免费人工找货