MPC8313ECVRAFF

Freescale Semiconductor Technical Data Document Number: MPC8313EEC Rev. 0, 06/2007 MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications This document provides an overview of the MPC8313E PowerQUICC™ II Pro processor features, including a block diagram showing the major functional components. The MPC8313E is a cost-effective, low-power, highly integrated host processor that addresses the requirements of several printing and imaging, consumer, and industrial applications, including main CPUs and I/O processors in printing systems, networking switches and line cards, wireless LANs (WLANs), network access servers (NAS), VPN routers, intelligent NIC, and industrial controllers. The MPC8313E extends the PowerQUICC™ family, adding higher CPU performance, additional functionality, and faster interfaces while addressing the requirements related to time-to-market, price, power consumption, and package size. Contents Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . 7 Power Characteristics . . . . . . . . . . . . . . . . . . . . . . . . 11 Clock Input Timing . . . . . . . . . . . . . . . . . . . . . . . . . . 13 RESET Initialization . . . . . . . . . . . . . . . . . . . . . . . . . 14 DDR and DDR2 SDRAM . . . . . . . . . . . . . . . . . . . . . 16 DUART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Ethernet: Three-Speed Ethernet, MII Management . 23 USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Local Bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 JTAG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 I2C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 PCI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Timers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 GPIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 IPIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 SPI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Package and Pin Listings . . . . . . . . . . . . . . . . . . . . . 56 Clocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Thermal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 System Design Information . . . . . . . . . . . . . . . . . . . 81 Document Revision History . . . . . . . . . . . . . . . . . . . 87 Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . 87 1 Overview The MPC8313E incorporates the e300c3 core, which includes 16 Kbytes of L1 instruction and data caches and on-chip memory management units (MMUs). The MPC8313E has interfaces to dual enhanced three-speed 10, 100, 1000 Mbps Ethernet controllers, a DDR1/DDR2 SDRAM memory controller, an enhanced local bus controller, a 32-bit PCI controller, a dedicated security This document contains information on a new product. Specifications and information herein are subject to change without notice. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. © Freescale Semiconductor, Inc., 2007. All rights reserved. Overview engine, a USB 2.0 dual-role controller and an on-chip full-speed PHY, a programmable interrupt controller, dual I2C controllers, a 4-channel DMA controller, and a general-purpose I/O port. A block diagram of the MPC8313E is shown in Figure 1. DUART Dual I 2C Timers GPIO e300c3 Core w/FPU and Power Management Interrupt Controller 16-KB I-Cache 16-KB D-Cache Local Bus, SPI DDR1/DDR2 Controller I/O Sequencer (IOS) Security Engine 2.2 USB 2.0 Host/Device/OTG ULPI On-Chip FS PHY Gb Ethernet MAC Gb Ethernet MAC PCI DMA Note: The MPC8313 does not include a security engine. Figure 1. MPC8313E Block Diagram The MPC8313E’s security engine (SEC 2.2) allows CPU-intensive cryptographic operations to be offloaded from the main CPU core. The security-processing accelerator provides hardware acceleration for the DES, 3DES, AES, SHA-1, and MD-5 algorithms. 1.1 MPC8313E Features The following features are supported in the MPC8313E. • Embedded PowerPCTM e300 processor core; operates at up to 333 MHz. • High-performance, low-power, and cost-effective host processor • DDR1/DDR2 memory controller—one 16-/32-bit interface at up to 333 MHz supporting both DDR1 and DDR2 • e300c3 core, built on Power Architecture™ technology, with 16-Kbyte instruction cache and 16-Kbyte data cache, a floating point unit, and two integer units • Peripheral interfaces such as 32-bit PCI interface with up to 66-MHz operation, 16-bit enhanced local bus interface with up to 66-MHz operation, and USB 2.0 (full speed) with an on-chip PHY. • Security engine provides acceleration for control and data plane security protocols • Power management controller for low-power consumption • High degree of software compatibility with previous-generation PowerQUICC processor-based designs for backward compatibility and easier software migration MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 2 Freescale Semiconductor Overview 1.2 Serial Interfaces The following interfaces are supported in the MPC8313E. • Dual UART, dual I2C, and an SPI interface 1.3 Security Engine The security engine is optimized to handle all the algorithms associated with IPSec, IEEE Std. 802.11i™, and iSCSI. The security engine contains one crypto-channel, a controller, and a set of crypto execution units (EUs). The execution units are: • Data encryption standard execution unit (DEU), supporting DES and 3DES • Advanced encryption standard unit (AESU), supporting AES • Message digest execution unit (MDEU), supporting MD5, SHA1, SHA-224, SHA-256, and HMAC with any algorithm • One crypto-channel supporting multi-command descriptor chains 1.4 DDR Memory Controller The MPC8313E DDR1/DDR2 memory controller includes the following features: • Single 16- or 32-bit interface supporting both DDR1 and DDR2 SDRAM • Support for up to 333-MHz • Support for two physical banks (chip selects), each bank independently addressable • 64-Mbit to 1-Gbit devices with x8/x16/x32 data ports (no direct x4 support) • Support for one 16-bit device or two 8-bit devices on a 16-bit bus OR one 32-bit device or two 16-bit devices on a 32-bit bus • Support for up to 16 simultaneous open pages • Supports auto refresh • On-the-fly power management using CKE • 1.8-/2.5-V SSTL2 compatible I/O 1.5 PCI Controller The MPC8313E PCI controller includes the following features: • PCI specification revision 2.3 compatible • Single 32-bit data PCI interface operates at up to 66 MHz • PCI 3.3-V compatible (not 5-V compatible) • Support for host and agent modes • On-chip arbitration, supporting three external masters on PCI • Selectable hardware-enforced coherency MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 3 Overview 1.6 USB Dual-Role Controller The MPC8313E USB controller includes the following features: • Supports USB on-the-go mode, which includes both device and host functionality, when using an external ULPI (UTMI + low-pin interface) PHY • Complies with USB Specification, Rev. 2.0 • Supports operation as a stand-alone USB device — Supports one upstream facing port — Supports three programmable USB endpoints • Supports operation as a stand-alone USB host controller — Supports USB root hub with one downstream-facing port — Enhanced host controller interface (EHCI) compatible • Supports full-speed (12 Mbps), and low-speed (1.5 Mbps) operation. Low-speed operation is supported only in host mode. • Supports UTMI + low pin interface (ULPI) or on-chip USB-2.0 full-speed PHY 1.7 Dual Enhanced Three-Speed Ethernet Controllers (eTSECs) The MPC8313E eTSECs include the following features: • Two RGMII/SGMII/MII/RMII/RTBI interfaces • Two controllers designed to comply with IEEE Stds. 802.3™, 802.3u™, 802.3x™, 802.3z™, 802.3au™, and 802.3ab™ • Support for Wake-on-Magic Packet™, a method to bring the device from standby to full operating mode • MII management interface for external PHY control and status • Three-speed support (10/100/1000 Mbps) • On-chip high-speed serial interface to external SGMII PHY interface • Support for IEEE Std. 1588™ • Support for two full-duplex FIFO interface modes • Multiple PHY interface configuration • TCP/IP acceleration and QoS features available • IP v4 and IP v6 header recognition on receive • IP v4 header checksum verification and generation • TCP and UDP checksum verification and generation • Per-packet configurable acceleration • Recognition of VLAN, stacked (queue in queue) VLAN, IEEE Std. 802.2™, PPPoE session, MPLS stacks, and ESP/AH IP-security headers • Transmission from up to eight physical queues. • Reception to up to eight physical queues MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 4 Freescale Semiconductor Overview • • • • • • • • • • • • • • • • • • • • Full- and half-duplex Ethernet support (1000 Mbps supports only full-duplex): IEEE Std. 802.3 full-duplex flow control (automatic PAUSE frame generation or software-programmed PAUSE frame generation and recognition) Programmable maximum frame length supports jumbo frames (up to 9.6 Kbytes) and IEEE Std. 802.1™ virtual local area network (VLAN) tags and priority VLAN insertion and deletion Per-frame VLAN control word or default VLAN for each eTSEC Extracted VLAN control word passed to software separately Retransmission following a collision CRC generation and verification of inbound/outbound packets Programmable Ethernet preamble insertion and extraction of up to 7 bytes MAC address recognition: Exact match on primary and virtual 48-bit unicast addresses VRRP and HSRP support for seamless router fail-over Up to 16 exact-match MAC addresses supported Broadcast address (accept/reject) Hash table match on up to 512 multicast addresses Promiscuous mode Buffer descriptors backward compatible with MPC8260 and MPC860T 10/100 Ethernet programming models RMON statistics support 10-Kbyte internal transmit and 2-Kbyte receive FIFOs MII management interface for control and status 1.8 Programmable Interrupt Controller (PIC) The programmable interrupt controller (PIC) implements the necessary functions to provide a flexible solution for general-purpose interrupt control. The PIC programming model supports 5 external and 34 internal discrete interrupt sources. Interrupts can also be redirected to an external interrupt controller. 1.9 Power Management Controller (PMC) The MPC8313E power management controller includes the following features: • Provides power management when the device is used in both host and agent modes • Supports PCI Power Management 1.2 D0, D1, D2, D3hot, and D3cold states • On-chip split power supply controlled through external power switch for minimum standby power • Support for PME generation in PCI agent mode, PME detection in PCI host mode • Supports wake-up from Ethernet (magic packet), USB, GPIO, and PCI (PME input as host) MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 5 Overview 1.10 Serial Peripheral Interface (SPI) The serial peripheral interface (SPI) allows the MPC8313E to exchange data between other PowerQUICC family chips, Ethernet PHYs for configuration, and peripheral devices such as EEPROMs, real-time clocks, A/D converters, and ISDN devices. The SPI is a full-duplex, synchronous, character-oriented channel that supports a four-wire interface (receive, transmit, clock, and slave select). The SPI block consists of transmitter and receiver sections, an independent baud-rate generator, and a control unit. 1.11 DMA Controller, Dual I2C, DUART, Local Bus Controller, and Timers The MPC8313E provides an integrated four-channel DMA controller with the following features: • Allows chaining (both extended and direct) through local memory-mapped chain descriptors (accessible by local masters). • Supports misaligned transfers There are two I2C controllers. These synchronous, multi-master buses can be connected to additional devices for expansion and system development. The DUART supports full-duplex operation and is compatible with the PC16450 and PC16550 programming models. 16-byte FIFOs are supported for both the transmitter and the receiver. The MPC8313E local bus controller (LBC) port allows connections with a wide variety of external DSPs and ASICs. Three separate state machines share the same external pins and can be programmed separately to access different types of devices. The general-purpose chip select machine (GPCM) controls accesses to asynchronous devices using a simple handshake protocol. The three user programmable machines (UPMs) can be programmed to interface to synchronous devices or custom ASIC interfaces. Each chip select can be configured so that the associated chip interface can be controlled by the GPCM or UPM controller. The FCM provides a glueless interface to parallel-bus NAND Flash E2PROM devices. The FCM contains three basic configuration register groups–BRn, ORn, and FMR. Both may exist in the same system. The local bus can operate at up to 66 MHz. The MPC8313E system timers include the following features: periodic interrupt timer, real time clock, software watchdog timer, and two general-purpose timer blocks. MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 6 Freescale Semiconductor Electrical Characteristics 2 Electrical Characteristics This section provides the AC and DC electrical specifications and thermal characteristics for the MPC8313E. The MPC8313E is currently targeted to these specifications. Some of these specifications are independent of the I/O cell, but are included for a more complete reference. These are not purely I/O buffer design specifications. 2.1 Overall DC Electrical Characteristics This section covers the ratings, conditions, and other characteristics. 2.1.1 Absolute Maximum Ratings Table 1. Absolute Maximum Ratings 1 Characteristic Symbol VDD AV DD GVDD NVDD/LVDD LVDDA/LVDDB DDR DRAM signals DDR DRAM reference Enhanced Three-speed Ethernet signals MVIN MVREF LVIN Max Value –0.3 to 1.26 –0.3 to 1.26 –0.3 to 2.75 –0.3 to 1.98 –0.3 to 3.6 –0.3 to 3.6 –0.3 to (GVDD + 0.3) –0.3 to (GVDD + 0.3) –0.3 to (LVDDA + 0.3) or –0.3 to (LVDDB + 0.3) –0.3 to (NVDD + 0.3) Unit V V V V V V V V 2, 5 2, 5 4, 5 Notes Table 1 provides the absolute maximum ratings. Core supply voltage PLL supply voltage DDR and DDR2 DRAM I/O voltage PCI, local bus, DUART, system control and power management, I2C, and JTAG I/O voltage eTSEC, USB Input voltage Local bus, DUART, SYS_CLK_IN, system control, and power management, I2C, and JTAG signals PCI OVIN V 3, 5 OVIN –0.3 to (NVDD + 0.3) V 6 MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 7 Electrical Characteristics Table 1. Absolute Maximum Ratings 1 (continued) Characteristic Storage temperature range Symbol TSTG Max Value –55 to 150 Unit °C Notes Notes: 1. Functional and tested operating conditions are given in Table 2. Absolute maximum ratings are stress ratings only, and functional operation at the maximums is not guaranteed. Stresses beyond those listed may affect device reliability or cause permanent damage to the device. 2. Caution: MVIN must not exceed GVDD by more than 0.3 V. This limit may be exceeded for a maximum of 20 ms during power-on reset and power-down sequences. 3. Caution: OVIN must not exceed NVDD by more than 0.3 V. This limit may be exceeded for a maximum of 20 ms during power-on reset and power-down sequences. 4. Caution: LVIN must not exceed LVDDA/LVDDB by more than 0.3 V. This limit may be exceeded for a maximum of 20 ms during power-on reset and power-down sequences. 5. (L,M,O)VIN and MV REF may overshoot/undershoot to a voltage and for a maximum duration as shown in Figure 2. 6. OVIN on the PCI interface may overshoot/undershoot according to the PCI Electrical Specification for 3.3-V operation, as shown in Figure 3. 2.1.2 Power Supply Voltage Specification Table 2 provides the recommended operating conditions for the MPC8313E. Note that the values in Table 2 are the recommended and tested operating conditions. Proper device operation outside of these conditions is not guaranteed. Table 2. Recommended Operating Conditions Characteristic SerDes (Lynx) internal digital power SerDes (Lynx) internal digital power SerDes (Lynx) I/O digital power SerDes (Lynx) I/O digital power SerDes (Lynx) analog power for PLL SerDes (Lynx) analog power for PLL Dedicated 3.3 V analog power for USB PLL Dedicated 1.0 V analog power for USB PLL Dedicated analog ground for USB PLL Dedicated USB power for USB Bias circuit Dedicated USB ground for USB Bias circuit Dedicated power for USB Transceiver Dedicated ground for USB transceiver Core supply voltage Internal core logic constant power Symbol XCOREVDD XCOREVSS XPADVDD XPADVSS SDAVDD SDAVSS USB_PLL_PWR3 USB_PLL_PWR1 USB_PLL_GND USB_VDDA_BIAS USB_VSSA_BIAS USB_VDDA USB_VSSA VDD VDDC Recommended Value1 1.0 0.0 1.0 0.0 1.0 0.0 3.3 1.0 0.0 3.3 0.0 3.3 0.0 1.0 1.0 Unit V V V V V V V V V V V V V V V 560 mA 454 mA 75 mA 4–5 mA 2–3 mA 2–3 mA 10 mA 10mA Current requirement 100 mA MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 8 Freescale Semiconductor Electrical Characteristics Table 2. Recommended Operating Conditions (continued) Characteristic Analog power for e300 core APLL Analog power for system APLL DDR and DDR2 DRAM I/O voltage Differential reference voltage for DDR controller Standard I/O Voltage eTSEC2 IO Supply eTSEC1/USB DR IO Supply Supply for eLBCIOs Analog and Digital Ground Symbol AVDD1 AVDD2 GVDD MVREF NVDD LVDDA LVDDB LVDD VSS Recommended Value1 1.0 1.0 2.5/1.8 1/2 DDR Supply 3.3 2.5/3.3 2.5/3.3 3.3 0.0 Unit V V V V V V V V V 27 mA 85 mA 85 mA 60 mA Current requirement 10 mA 10 mA 425 mA Notes: 1. GVDD, OVDD, AVDD, and VDD must track each other and must vary in the same direction–either in the positive or negative direction. Figure 2 shows the undershoot and overshoot voltages at the interfaces of the MPC8313E. G/L/NVDD + 20% G/L/NVDD + 5% VIH G/L/NVDD VSS VSS – 0.3 V VIL VSS – 0.7 V Not to Exceed 10% of tinterface1 Note: 1. Note that tinterface refers to the clock period associated with the bus clock interface. Figure 2. Overshoot/Undershoot Voltage for GVDD/NVDD/LVDD MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 9 Electrical Characteristics Figure 3 shows the undershoot and overshoot voltage of the PCI interface of the MPC8313E for the 3.3-V signals, respectively. 11 ns (Min) +7.1 V Overvoltage Waveform 0V 4 ns (Max) 62.5 ns +3.6 V Undervoltage Waveform –3.5 V 7.1 V p-to-p (Min) 7.1 V p-to-p (Min) 4 ns (Max) Figure 3. Maximum AC Waveforms on PCI Interface for 3.3-V Signaling 2.1.3 Output Driver Characteristics Table 3 provides information on the characteristics of the output driver strengths. The values are preliminary estimates. Table 3. Output Drive Capability Driver Type Local bus interface utilities signals PCI signals DDR signal DDR2 signal DUART, system control, I2C, JTAG,SPI GPIO signals eTSEC signals USB Signals Output Impedance (Ω ) 42 25 18 18 42 42 42 42 GVDD = 2.5 V GVDD = 1.8 V NVDD = 3.3 V NVDD = 3.3 V LVDDA, LV DDB = 2.5/3.3 V LVDDB = 2.5/3.3 V Supply Voltage NVDD = 3.3 V 2.2 Power Sequencing The MPC8313E does not require the core supply voltage and IO supply voltages to be applied in any particular order. Note that during the power ramp-up, before the power supplies are stable, there might be a period when IO pins are actively driven. After the power is stable, as long as PORESET is asserted, most IO pins are tri-stated. In order to minimize the time that IO pins are being actively driven, it is MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 10 Freescale Semiconductor Power Characteristics recommended to apply core voltage before IO voltage and assert PORESET before the power supplies fully ramp up. 3 . Power Characteristics Table 4. MPC8313E Power Dissipation 1 Core Frequency (MHz) 267 333 CSB Frequency (MHz) 133 167 Typical 2, 3 680 820 Maximum 2,3 880 1020 Unit mW mW The estimated typical power dissipation for this family of MPC8313E devices is shown in Table 4, and Table 5 shows the estimated typical I/O power dissipation. Note: 1. The values do not include I/O supply power or AVdd. 2. Typical power is based on a voltage of Vdd = 1.05V, a junction temperature of Tj = 105°C, and an artificial smoker test. 3. These are preliminary estimates 1 Table 5. MPC8313E Typical I/O Power Dissipation Interface Parameter GVDD GVDD NVDD LVDDA/LV DDB LVDDA/LVDDB LVDDB Unit Comments (1.8 V) (2.5 V) (3.3 V) (3.3V) (2.5V) (3.3V) — — — 0.355 0.323 0.291 W W W DDR 1, 60% utilzation, 333MHz, 32 bits 50% read/write 266MHz, 32 bits Rs = 22Ω Rt = 50Ω 200MHz, 32 bits single pair of clock Capacitive Load: Data = 8pF, Control Address = 8pF, Clock = 8pF DDR 2, 60% utilization, 333MHz, 32 bits 0.266 50% read/write 266MHz, 32 bits 0.246 Rs = 22Ω Rt = 75Ω 200MHz, 32bits 0.225 single pair of clock Capacitive Load: Data = 8pF, Control Address = 8pF, Clock = 8pF PCI I/O load = 50pF 33 MHz 66 MHz Local bus I/O load = 20pF 66 MHz 50 MHz — — — W W W 0.120 0.249 0.056 0.040 W W W W MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 11 Power Characteristics Table 5. MPC8313E Typical I/O Power Dissipation (continued) TSEC I/O load = 20pF MII, 25MHz RGMII, 125MHz 0.008 0.044 W W Multiple by number of interface used USBDR controller load = 20pF Other I/O 60 MHz 0.015 0.078 W W MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 12 Freescale Semiconductor Clock Input Timing 4 4.1 Clock Input Timing DC Electrical Characteristics This section provides the clock input DC and AC electrical characteristics for the MPC8313E. Table 6 provides the clock input (SYS_CLK_IN/PCI_SYNC_IN) DC timing specifications for the MPC8313E. Table 6. SYS_CLK_IN DC Electrical Characteristics Parameter Input high voltage Input low voltage SYS_CLK_IN Input current PCI_SYNC_IN Input current PCI_SYNC_IN Input current Condition — — 0 V ≤ VIN ≤ NVDD 0 V ≤ VIN ≤ 0.5 V or NVDD – 0.5 V ≤ VIN ≤ NV DD 0.5 V ≤ VIN ≤ NVDD – 0.5 V Symbol VIH VIL IIN IIN IIN Min 2.7 –0.3 — — — Max NVDD + 0.3 0.4 ±10 ±10 ±50 Unit V V μA μA μA 4.2 AC Electrical Characteristics The primary clock source for the MPC8313E can be one of two inputs, SYS_CLK_IN or PCI_CLK, depending on whether the device is configured in PCI host or PCI agent mode. Table 7 provides the clock input (SYS_CLK_IN/PCI_CLK) AC timing specifications for the MPC8313E. Table 7. SYS_CLK_IN AC Timing Specifications Parameter/Condition SYS_CLK_IN/PCI_CLK frequency SYS_CLK_IN/PCI_CLK cycle time SYS_CLK_IN/PCI_CLK rise and fall time SYS_CLK_IN/PCI_CLK duty cycle SYS_CLK_IN/PCI_CLK jitter Symbol fSYS_CLK_IN tSYS_CLK_IN tKH, tKL tKHK/tSYS_CLK_IN — Min 25 15 0.6 40 — Typical — — 0.8 — — Max 66 — 1.2 60 ±150 Unit MHz ns ns % ps Notes 1 — 2 3 4, 5 Notes: 1. Caution: The system, core, security block must not exceed their respective maximum or minimum operating frequencies. 2. Rise and fall times for SYS_CLK_IN/PCI_CLK are measured at 0.4 V and 2.7 V. 3. Timing is guaranteed by design and characterization. 4. This represents the total input jitter—short term and long term—and is guaranteed by design. 5. The SYS_CLK_IN/PCI_CLK driver’s closed loop jitter bandwidth should be < 500 kHz at –20 dB. The bandwidth must be set low to allow cascade-connected PLL-based devices to track SYS_CLK_IN drivers with the specified jitter. MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 13 RESET Initialization 5 RESET Initialization This section describes the DC and AC electrical specifications for the reset initialization timing and electrical requirements of the MPC8313E. 5.1 RESET DC Electrical Characteristics Table 8. RESET Pins DC Electrical Characteristics Characteristic Input high voltage Input low voltage Input current Output high voltage Output low voltage Output low voltage Symbol VIH VIL IIN VOH VOL VOL 0 V ≤ VIN ≤ NVDD IOH = –8.0 mA IOL = 8.0 mA IOL = 3.2 mA 2.4 — — Condition Min 2.0 –0.3 Max NVDD + 0.3 0.8 ±5 — 0.5 0.4 Unit V V μA V V V Table 8 provides the DC electrical characteristics for the RESET pins. 5.2 RESET AC Electrical Characteristics Table 9. RESET Initialization Timing Specifications Parameter/Condition Min 32 32 32 512 16 4 Max — — — — — — Unit tPCI_SYNC_IN tSYS_CLK_IN tPCI_SYNC_IN tPCI_SYNC_IN tPCI_SYNC_IN tSYS_CLK_IN Notes 1 2 1 1 1 2 Table 9 provides the reset initialization AC timing specifications. Required assertion time of HRESET or SRESET (input) to activate reset flow Required assertion time of PORESET with stable clock applied to SYS_CLK_IN when the device is in PCI host mode Required assertion time of PORESET with stable clock applied to PCI_SYNC_IN when the device is in PCI agent mode HRESET/ SRESET assertion (output) HRESET negation to SRESET negation (output) Input setup time for POR configuration signals (CFG_RESET_SOURCE[0:3] and CFG_SYS_CLK_IN_DIV ) with respect to negation of PORESET when the device is in PCI host mode Input setup time for POR configuration signals (CFG_RESET_SOURCE[0:2] and CFG_CLKIN_DIV) with respect to negation of PORESET when the device is in PCI agent mode Input hold time for POR configuration signals with respect to negation of HRESET 4 — tPCI_SYNC_IN 1 0 — ns MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 14 Freescale Semiconductor RESET Initialization Table 9. RESET Initialization Timing Specifications (continued) Time for the device to turn off POR configuration signals with respect to the assertion of HRESET Time for the device to turn on POR configuration signals with respect to the negation of HRESET — 1 4 — ns tPCI_SYNC_IN 3 1, 3 Notes: 1. tPCI_SYNC_IN is the clock period of the input clock applied to PCI_SYNC_IN. When the device is In PCI host mode the primary clock is applied to the SYS_CLK_IN input, and PCI_SYNC_IN period depends on the value of CFG_CLKIN_DIV. 2. tSYS_CLK_IN is the clock period of the input clock applied to SYS_CLK_IN. It is only valid when the device is in PCI host mode. 3. POR configuration signals consists of CFG_RESET_SOURCE[0:2] and CFG_CLKIN_DIV. Table 10 provides the PLL lock times. Table 10. PLL Lock Times Parameter/Condition PLL lock times Min — Max 100 Unit μs Notes MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 15 DDR and DDR2 SDRAM 6 DDR and DDR2 SDRAM This section describes the DC and AC electrical specifications for the DDR SDRAM interface. Note that DDR SDRAM is GVDD(typ) = 2.5 V and DDR2 SDRAM is GVDD(typ) = 1.8 V. 6.1 DDR and DDR2 SDRAM DC Electrical Characteristics Table 11 provides the recommended operating conditions for the DDR2 SDRAM component(s) when GVDD(typ) = 1.8 V. Table 11. DDR2 SDRAM DC Electrical Characteristics for GVDD(typ) = 1.8 V Parameter/Condition I/O supply voltage I/O reference voltage I/O termination voltage Input high voltage Input low voltage Output leakage current Output high current (VOUT = 1.420 V) Output low current (VOUT = 0.280 V) Symbol GVDD MV REF VTT VIH VIL IOZ IOH IOL Min 1.7 0.49 × GVDD MVREF – 0.04 MVREF + 0.125 –0.3 –9.9 –13.4 13.4 Max 1.9 0.51 × GVDD MVREF + 0.04 GVDD + 0.3 MV REF – 0.125 9.9 — — Unit V V V V V μA mA mA 4 Notes 1 2 3 Notes: 1. GVDD is expected to be within 50 mV of the DRAM GVDD at all times. 2. MVREF is expected to be equal to 0.5 × G VDD, and to track GVDD DC variations as measured at the receiver. Peak-to-peak noise on MVREF may not exceed ±2% of the DC value. 3. VTT is not applied directly to the device. It is the supply to which far end signal termination is made and is expected to be equal to MV REF. This rail should track variations in the DC level of MVREF. 4. Output leakage is measured with all outputs disabled, 0 V ≤ VOUT ≤ GVDD. Table 12 provides the DDR2 capacitance when GVDD(typ) = 1.8 V. Table 12. DDR2 SDRAM Capacitance for GVDD(typ)=1.8 V Parameter/Condition Input/output capacitance: DQ, DQS, DQS Delta input/output capacitance: DQ, DQS, DQS Symbol CIO CDIO Min 6 — Max 8 0.5 Unit pF pF Notes 1 1 Note: 1. This parameter is sampled. GV DD = 1.8 V ± 0.090 V, f = 1 MHz, TA = 25°C, VOUT = GVDD/2, VOUT (peak-to-peak) = 0.2 V. MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 16 Freescale Semiconductor DDR and DDR2 SDRAM Table 13 provides the recommended operating conditions for the DDR SDRAM component(s) when GVDD(typ) = 2.5 V. Table 13. DDR SDRAM DC Electrical Characteristics for GVDD (typ) = 2.5 V Parameter/Condition I/O supply voltage I/O reference voltage I/O termination voltage Input high voltage Input low voltage Output leakage current Output high current (VOUT = 1.95 V) Output low current (VOUT = 0.35 V) Symbol GVDD MVREF VTT VIH VIL IOZ IOH IOL Min 2.3 0.49 × G VDD MVREF – 0.04 MVREF + 0.15 –0.3 –9.9 –16.2 16.2 Max 2.7 0.51 × GVDD MVREF + 0.04 GVDD + 0.3 MVREF – 0.15 –9.9 — — Unit V V V V V μA mA mA 4 Notes 1 2 3 Notes: 1. GVDD is expected to be within 50 mV of the DRAM GVDD at all times. 2. MVREF is expected to be equal to 0.5 × GVDD, and to track GV DD DC variations as measured at the receiver. Peak-to-peak noise on MVREF may not exceed ±2% of the DC value. 3. VTT is not applied directly to the device. It is the supply to which far end signal termination is made and is expected to be equal to MVREF. This rail should track variations in the DC level of MVREF. 4. Output leakage is measured with all outputs disabled, 0 V ≤ VOUT ≤ GVDD. Table 14 provides the DDR capacitance when GVDD (typ)=2.5 V. Table 14. DDR SDRAM Capacitance for GVDD (typ) = 2.5 V Parameter/Condition Input/output capacitance: DQ, DQS Delta input/output capacitance: DQ, DQS Symbol CIO CDIO Min 6 — Max 8 0.5 Unit pF pF Notes 1 1 Note: 1. This parameter is sampled. GVDD = 2.5 V ± 0.125 V, f = 1 MHz, TA = 25°C, VOUT = GVDD /2, VOUT (peak-to-peak) = 0.2 V. Table 15 provides the current draw characteristics for MVREF. Table 15. Current Draw Characteristics for MVREF Parameter / Condition Current draw for MVREF Symbol IMVREF Min — Max 500 Unit μA Note 1 1. The voltage regulator for MVREF must be able to supply up to 500 μA current. MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 17 DDR and DDR2 SDRAM 6.2 DDR and DDR2 SDRAM AC Electrical Characteristics This section provides the AC electrical characteristics for the DDR SDRAM interface. 6.2.1 DDR and DDR2 SDRAM Input AC Timing Specifications Table 16. DDR2 SDRAM Input AC Timing Specifications for 1.8-V Interface Table 16 provides the input AC timing specifications for the DDR2 SDRAM when GVDD(typ)=1.8 V. At recommended operating conditions with GVDD of 1.8 ±5% Parameter AC input low voltage AC input high voltage Symbol VIL VIH Min — MVREF + 0.25 Max MVREF – 0.25 — Unit V V Notes Table 17 provides the input AC timing specifications for the DDR SDRAM when GVDD(typ)=2.5 V. Table 17. DDR SDRAM Input AC Timing Specifications for 2.5-V Interface At recommended operating conditions with GVDD of 2.5 ±5%. Parameter AC input low voltage AC input high voltage Symbol VIL VIH Min — MVREF + 0.31 Max MVREF – 0.31 — Unit V V Notes Table 18 provides the input AC timing specifications for the DDR2 SDRAM interface. Table 18. DDR and DDR2 SDRAM Input AC Timing Specifications At recommended operating conditions. with GVDD of 2.5 ±5% Parameter Controller Skew for MDQS—MDQ//MDM 333 MHz 266 MHz 200 MHz Symbol tCISKEW Min Max Unit ps Notes 1, 2 –750 –750 –1250 750 750 1250 Note: 1. tCISKEW represents the total amount of skew consumed by the controller between MDQS[n] and any corresponding bit that will be captured with MDQS[n]. This should be subtracted from the total timing budget. 2. The amount of skew that can be tolerated from MDQS to a corresponding MDQ signal is called tDISKEW. This can be determined by the following equation: tDISKEW = +/–(T/4 – abs(tCISKEW)) where T is the clock period and abs(tCISKEW) is the absolute value of tCISKEW. MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 18 Freescale Semiconductor DDR and DDR2 SDRAM 6.2.2 DDR and DDR2 SDRAM Output AC Timing Specifications Table 19. DDR and DDR2 SDRAM Output AC Timing Specifications At recommended operating conditions. Parameter MCK[n] cycle time, MCK[n]/MCK[n] crossing ADDR/CMD output setup with respect to MCK 333 MHz 266 MHz 200 MHz ADDR/CMD output hold with respect to MCK 333 MHz 266 MHz 200 MHz MCS[n] output setup with respect to MCK 333 MHz 266 MHz 200 MHz MCS[n] output hold with respect to MCK 333 MHz 266 MHz 200 MHz MCK to MDQS Skew MDQ//MDM output setup with respect to MDQS 333 MHz 266 MHz 200 MHz MDQ//MDM output hold with respect to MDQS 333 MHz 266 MHz 200 MHz Symbol 1 tMCK tDDKHAS Min 6 Max 10 Unit ns ns Notes 2 3 2.1 2.5 3.5 tDDKHAX 2.40 3.15 4.20 tDDKHCS 2.40 3.15 4.20 tDDKHCX 2.40 3.15 4.20 tDDKHMH tDDKHDS, tDDKLDS 800 900 1000 tDDKHDX, tDDKLDX 900 1100 1200 –0.6 — — — ns — — — ns — — — ns — — — 0.6 ns ps — — — ps — — — 5 4 5 3 3 3 MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 19 DDR and DDR2 SDRAM Table 19. DDR and DDR2 SDRAM Output AC Timing Specifications (continued) At recommended operating conditions. Parameter MDQS preamble start MDQS epilogue end Symbol 1 tDDKHMP tDDKHME Min –0.5 × tMCK – 0.6 –0.6 Max –0.5 × tMCK +0.6 0.6 Unit ns ns Notes 6 6 Note: 1. The symbols used for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. Output hold time can be read as DDR timing (DD) from the rising or falling edge of the reference clock (KH or KL) until the output went invalid (AX or DX). For example, tDDKHAS symbolizes DDR timing (DD) for the time tMCK memory clock reference (K) goes from the high (H) state until outputs (A) are setup (S) or output valid time. Also, tDDKLDX symbolizes DDR timing (DD) for the time tMCK memory clock reference (K) goes low (L) until data outputs (D) are invalid (X) or data output hold time. 2. All MCK/MCK referenced measurements are made from the crossing of the two signals ±0.1 V. 3. ADDR/CMD includes all DDR SDRAM output signals except MCK/MCK, MCS, and MDQ//MDM/MDQS. 4. Note that tDDKHMH follows the symbol conventions described in note 1. For example, tDDKHMH describes the DDR timing (DD) from the rising edge of the MCK[n] clock (KH) until the MDQS signal is valid (MH). tDDKHMH can be modified through control of the DQSS override bits in the TIMING_CFG_2 register. This will typically be set to the same delay as the clock adjust in the CLK_CNTL register. The timing parameters listed in the table assume that these 2 parameters have been set to the same adjustment value. See the MPC8313E PowerQUICC II Pro Host Processor Reference Manual for a description and understanding of the timing modifications enabled by use of these bits. 5. Determined by maximum possible skew between a data strobe (MDQS) and any corresponding bit of data (MDQ), ECC (MECC), or data mask (MDM). The data strobe should be centered inside of the data eye at the pins of the microprocessor. 6. All outputs are referenced to the rising edge of MCK[n] at the pins of the microprocessor. Note that tDDKHMP follows the symbol conventions described in note 1. NOTE For the ADDR/CMD setup and hold specifications in Table 19, it is assumed that the clock control register is set to adjust the memory clocks by 1/2 applied cycle. Figure 4 shows the DDR SDRAM output timing for the MCK to MDQS skew measurement (tDDKHMH). MCK[n] MCK[n] tMCK tDDKHMHmax) = 0.6 ns MDQS tDDKHMH(min) = –0.6 ns MDQS Figure 4. Timing Diagram for tDDKHMH MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 20 Freescale Semiconductor DUART Figure 5 shows the DDR and DDR2 SDRAM output timing diagram. MCK[n] MCK[n] tMCK tDDKHAS ,tDDKHCS tDDKHAX ,tDDKHCX ADDR/CMD Write A0 tDDKHMP tDDKHMH MDQS[n] tDDKHDS tDDKLDS MDQ[x] tDDKHDX D0 D1 tDDKLDX tDDKHME NOOP Figure 5. DDR and DDR2 SDRAM Output Timing Diagram Figure 6 provides the AC test load for the DDR bus. Output Z0 = 50 Ω GVDD/2 RL = 5 0 Ω Figure 6. DDR AC Test Load 7 7.1 DUART DUART DC Electrical Characteristics Table 20. DUART DC Electrical Characteristics Parameter High-level input voltage Low-level input voltage NVDD High-level output voltage, IOH = –100 μA Symbol VIH VIL VOH Min 2 –0.3 NVDD – 0.2 Max NVDD + 0.3 0.8 — Unit V V V This section describes the DC and AC electrical specifications for the DUART interface. Table 20 provides the DC electrical characteristics for the DUART interface. MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 21 DUART Table 20. DUART DC Electrical Characteristics (continued) Low-level output voltage, IOL = 100 μA Input current (0 V ≤VIN ≤ NVDD) VOL IIN — — 0.2 ±5 V μA 7.2 DUART AC Electrical Specifications Table 21. DUART AC Timing Specifications Parameter Value 256 > 1,000,000 16 Unit baud baud — 1 2 Notes Table 21 provides the AC timing parameters for the DUART interface. Minimum baud rate Maximum baud rate Oversample rate Notes: 1. Actual attainable baud rate will be limited by the latency of interrupt processing. 2. The middle of a start bit is detected as the 8th sampled 0 after the 1-to-0 transition of the start bit. Subsequent bit values are sampled each 16th sample. MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 22 Freescale Semiconductor Ethernet: Three-Speed Ethernet, MII Management 8 Ethernet: Three-Speed Ethernet, MII Management This section provides the AC and DC electrical characteristics for three-speed, 10/100/1000, and MII management. 8.1 Enhanced Three-Speed Ethernet Controller (eTSEC) (10/100/1000 Mbps)—MII/RMII/RGMII/SGMII/RTBI Electrical Characteristics The electrical characteristics specified here apply to all the MII (media independent interface), RGMII (reduced gigabit media independent interface), SGMII (serial gigabit media independent interface), and RTBI (reduced ten-bit interface) signals except MDIO (management data input/output) and MDC (management data clock). The MII interface is defined for 3.3V, while the RMII, RGMII, SGMII, and RTBI interfaces can be operated at 3.3 or 2.5 V. The RGMII and RTBI interfaces follow the Hewlett-Packard reduced pin-count interface for Gigabit Ethernet Physical Layer Device Specification Version 1.2a (9/22/2000). The electrical characteristics for MDIO and MDC are specified in Section 8.3, “Ethernet Management Interface Electrical Characteristics.” 8.1.1 TSEC DC Electrical Characteristics All RGMII, SGMII, RMII, and RTBI drivers and receivers comply with the DC parametric attributes specified in Table 22 and Table 23. The potential applied to the input of a MII, RGMII, SGMII, or RTBI receiver may exceed the potential of the receiver’s power supply (that is, a RGMII driver powered from a 3.6-V supply driving VOH into a RGMII receiver powered from a 2.5-V supply). Tolerance for dissimilar RGMII driver and receiver supply potentials is implicit in these specifications. The RGMII and RTBI signals are based on a 2.5-V CMOS interface voltage as defined by JEDEC EIA/JESD8-5. Table 22. MII/RGMII/RTBI (When Operating at 3.3V) DC Electrical Characteristics Parameter Supply voltage 3.3 V Output high voltage Symbol LVDDA/LVDDB VOH IOH = –4.0 mA Conditions — LVDDA or LV DDB = Min Min 2.97 2.40 Max 3.63 LVDDA + 0.3 or LVDDB + 0.3 0.50 LVDDA + 0.3 or LVDDB + 0.3 0.90 40 — Unit V V Output low voltage Input high voltage VOL VIH IOL = 4.0 mA — LVDDA or LVDDB = Min — VSS 2.0 V V Input low voltage Input high current Input low current VIL IIH IIL — VIN 1= — LVDDA or LVDDB –0.3 — –600 V μA μA VIN 1 = VSS Note: 1. The symbol V IN, in this case, represents the LVIN symbol referenced in Table 1 and Table 2. MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 23 Ethernet: Three-Speed Ethernet, MII Management Table 23. RGMII/RTBI (When Operating at 2.5 V) DC Electrical Characteristics Parameters Supply voltage 2.5 V Output high voltage Symbol LVDDA/LVDDB VOH Conditions — IOH = –1.0 mA LVDDA or LV DDB = Min Min 2.37 2.00 Max 2.63 LVDDA + 0.3 or LVDDB + 0.3 0.40 LVDDA + 0.3 or LVDDB + 0.3 0.70 10 — Unit V V Output low voltage Input high voltage VOL VIH IOL = 1.0 mA — LVDDA or LV DDB = Min VSS – 0.3 LVDDA or LV DDB = Min 1.7 V V Input low voltage Input high current Input low current VIL IIH IIL — VIN 1= LVDDA or LV DDB = Min LVDDA or LVDDB –0.3 — –15 V μA μA VIN 1 = VSS Note: 1. Note that the symbol VIN, in this case, represents the LVIN symbol referenced in Table 1 and Table 2. 8.2 MII, RGMII, SGMII, and RTBI AC Timing Specifications The AC timing specifications for MII, RMII, RGMII, SGMII, and RTBI are presented in this section. 8.2.1 MII AC Timing Specifications This section describes the MII transmit and receive AC timing specifications. 8.2.1.1 MII Transmit AC Timing Specifications Table 24. MII Transmit AC Timing Specifications Table 24 provides the MII transmit AC timing specifications. At recommended operating conditions with LVDDA/LVDDB /NVDD of 3.3 V ± 10%. Parameter/Condition TX_CLK clock period 10 Mbps TX_CLK clock period 100 Mbps TX_CLK duty cycle TX_CLK to MII data TXD[3:0], TX_ER, TX_EN delay Symbol 1 tMTX tMTX tMTXH/tMTX tMTKHDX Min — — 35 1 Typ 400 40 — 5 Max — — 65 15 Unit ns ns % ns MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 24 Freescale Semiconductor Ethernet: Three-Speed Ethernet, MII Management Table 24. MII Transmit AC Timing Specifications (continued) At recommended operating conditions with LVDDA/LVDDB /NVDD of 3.3 V ± 10%. Parameter/Condition TX_CLK data clock rise VIL(min) to VIH(max) TX_CLK data clock fall VIH(max) to VIL(min) Symbol 1 tMTXR tMTXF Min 1.0 1.0 Typ — — Max 4.0 4.0 Unit ns ns Note: 1. The symbols used for timing specifications herein follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tMTKHDX symbolizes MII transmit timing (MT) for the time tMTX clock reference (K) going high (H) until data outputs (D) are invalid (X). Note that, in general, the clock reference symbol representation is based on two to three letters representing the clock of a particular functional. For example, the subscript of tMTX represents the MII(M) transmit (TX) clock. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall). Figure 7 shows the MII transmit AC timing diagram. tMTX TX_CLK tMTXH TXD[3:0] TX_EN TX_ER tMTKHDX tMTXF tMTXR Figure 7. MII Transmit AC Timing Diagram 8.2.1.2 MII Receive AC Timing Specifications Table 25. MII Receive AC Timing Specifications Table 25 provides the MII receive AC timing specifications. At recommended operating conditions with LVDDA/LVDDB /NVDD of 3.3 V ± 10%. Parameter/Condition RX_CLK clock period 10 Mbps RX_CLK clock period 100 Mbps RX_CLK duty cycle RXD[3:0], RX_DV, RX_ER setup time to RX_CLK RXD[3:0], RX_DV, RX_ER hold time to RX_CLK Symbol 1 tMRX tMRX tMRXH/tMRX tMRDVKH tMRDXKH Min — — 35 10.0 10.0 Typ 400 40 — — — Max — — 65 — — Unit ns ns % ns ns MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 25 Ethernet: Three-Speed Ethernet, MII Management Table 25. MII Receive AC Timing Specifications (continued) At recommended operating conditions with LVDDA/LVDDB /NVDD of 3.3 V ± 10%. Parameter/Condition RX_CLK clock rise VIL(min) to VIH(max) RX_CLK clock fall time VIH(max) to VIL(min) Symbol 1 tMRXR tMRXF Min 1.0 1.0 Typ — — Max 4.0 4.0 Unit ns ns Note: 1. The symbols used for timing specifications herein follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tMRDVKH symbolizes MII receive timing (MR) with respect to the time data input signals (D) reach the valid state (V) relative to the tMRX clock reference (K) going to the high (H) state or setup time. Also, tMRDXKL symbolizes MII receive timing (GR) with respect to the time data input signals (D) went invalid (X) relative to the tMRX clock reference (K) going to the low (L) state or hold time. Note that, in general, the clock reference symbol representation is based on three letters representing the clock of a particular functional. For example, the subscript of tMRX represents the MII (M) receive (RX) clock. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall). Figure 8 provides the AC test load for TSEC. Output Z0 = 50 Ω RL = 5 0 Ω LVDDA/2 or LVDDB/2 Figure 8. TSEC AC Test Load Figure 9 shows the MII receive AC timing diagram. tMRX RX_CLK tMRXH RXD[3:0] RX_DV RX_ER tMRDVKH tMRDXKH tMRXF Valid Data tMRXR Figure 9. MII Receive AC Timing Diagram RMII AC Timing Specifications MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 26 Freescale Semiconductor Ethernet: Three-Speed Ethernet, MII Management 8.2.1.3 RMII Transmit AC Timing Specifications This section describes the RMII transmit and receive AC timing specifications. Table 26 provides the RMII transmit AC timing specifications. Table 26. RMII Transmit AC Timing Specifications At recommended operating conditions with NVDD of 3.3 V ± 10%. Parameter/Condition REF_CLK clock REF_CLK duty cycle REF_CLK to RMII data TXD[1:0], TX_EN delay REF_CLK data clock rise VIL(min) to V IH(max) REF_CLK data clock fall VIH(max) to VIL(min) Symbol 1 tRMX tRMXH/tRMX tRMTKHDX tRMXR tRMXF Min — 35 2 1.0 1.0 Typical 20 — — — Max — 65 10 4.0 4.0 Unit ns % ns ns ns Note: 1. The symbols used for timing specifications herein follow the pattern of t(first three letters of functional block)(signal)(state) (reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tRMTKHDX symbolizes RMII transmit timing (RMT) for the time tRMX clock reference (K) going high (H) until data outputs (D) are invalid (X). Note that, in general, the clock reference symbol representation is based on two to three letters representing the clock of a particular functional. For example, the subscript of tRMX represents the RMII(RM) reference (X) clock. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall). Figure 10 shows the RMII transmit AC timing diagram. tRMX REF_CLK tRMXH TXD[1:0] TX_EN tRMTKHDX tRMXF tRMXR Figure 10. RMII Transmit AC Timing Diagram 8.2.1.4 RMII Receive AC Timing Specifications Table 27. RMII Receive AC Timing Specifications Table 27 provides the RMII receive AC timing specifications. At recommended operating conditions with NVDD of 3.3 V ± 10%. Parameter/Condition REF_CLK clock period REF_CLK duty cycle RXD[1:0], CRS_DV, RX_ER setup time to REF_CLK RXD[1:0], CRS_DV, RX_ER hold time to REF_CLK Symbol 1 tRMX tRMXH/tRMX tRMRDVKH tRMRDXKH Min — 35 4.0 2.0 Typical 20 — — — Max — 65 — — Unit ns % ns ns MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 27 Ethernet: Three-Speed Ethernet, MII Management Table 27. RMII Receive AC Timing Specifications (continued) At recommended operating conditions with NVDD of 3.3 V ± 10%. Parameter/Condition REF_CLK clock rise VIL(min) to VIH(max) REF_CLK clock fall time VIH(max) to VIL(min) Symbol 1 tRMXR tRMXF Min 1.0 1.0 Typical — — Max 4.0 4.0 Unit ns ns Note: 1. The symbols used for timing specifications herein follow the pattern of t(first three letters of functional block)(signal)(state) (reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tRMRDVKH symbolizes RMII receive timing (RMR) with respect to the time data input signals (D) reach the valid state (V) relative to the tRMX clock reference (K) going to the high (H) state or setup time. Also, tRMRDXKL symbolizes RMII receive timing (RMR) with respect to the time data input signals (D) went invalid (X) relative to the tRMX clock reference (K) going to the low (L) state or hold time. Note that, in general, the clock reference symbol representation is based on three letters representing the clock of a particular functional. For example, the subscript of tRMX represents the RMII (RM) reference (X) clock. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall). Figure 11 provides the AC test load. Output Z0 = 50 Ω RL = 5 0 Ω NVDD/2 Figure 11. AC Test Load Figure 12 shows the RMII receive AC timing diagram. tRMX REF_CLK tRMXH RXD[1:0] CRS_DV RX_ER tRMRDVKH tRMRDXKH tRMXF Valid Data tRMXR Figure 12. RMII Receive AC Timing Diagram 8.2.2 RGMII and RTBI AC Timing Specifications Table 28. RGMII and RTBI AC Timing Specifications Table 28 presents the RGMII and RTBI AC timing specifications. At recommended operating conditions with LVDDA/LVDDB of 2.5 V ± 5%. Parameter/Condition Data to clock output skew (at transmitter) Data to clock input skew (at receiver) Clock cycle duration 3 2 Symbol 1 tSKRGT tSKRGT tRGT Min –0.5 1.0 7.2 Typ — — 8.0 Max 0.5 2.8 8.8 Unit ns ns ns MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 28 Freescale Semiconductor Ethernet: Three-Speed Ethernet, MII Management Table 28. RGMII and RTBI AC Timing Specifications (continued) At recommended operating conditions with LVDDA/LVDDB of 2.5 V ± 5%. Duty cycle for 1000Base-T 4, 5 Duty cycle for 10BASE-T and 100BASE-TX Rise time (20%–80%) Fall time (20%–80%) GTX_CLK125 reference clock period GTX_CLK125 reference clock duty cycle 3, 5 tRGTH/tRGT tRGTH/tRGT tRGTR tRGTF tG12 6 45 40 — — — 47 50 50 — — 8.0 — 55 60 0.75 0.75 — 53 % % ns ns ns % tG125H/tG125 Notes: 1. Note that, in general, the clock reference symbol representation for this section is based on the symbols RGT to represent RGMII and RTBI timing. For example, the subscript of tRGT represents the RTBI (T) receive (RX) clock. Note also that the notation for rise (R) and fall (F) times follows the clock symbol that is being represented. For symbols representing skews, the subscript is skew (SK) followed by the clock that is being skewed (RGT). 2. This implies that PC board design will require clocks to be routed such that an additional trace delay of greater than 1.5 ns will be added to the associated clock signal. 3. For 10 and 100 Mbps, tRGT scales to 400 ns ± 40 ns and 40 ns ± 4 ns, respectively. 4. Duty cycle may be stretched/shrunk during speed changes or while transitioning to a received packet's clock domains as long as the minimum duty cycle is not violated and stretching occurs for no more than three tRGT of the lowest speed transitioned between. 5. Duty cycle reference is LVDDA/2 or LVDDB/2. 6. This symbol is used to represent the external GTX_CLK125 and does not follow the original symbol naming convention. Figure 13 shows the RGMII and RTBI AC timing and multiplexing diagrams. tRGT tRGTH GTX_CLK (At Transmitter) tSKRGT TXD[8:5][3:0] TXD[7:4][3:0] TXD[8:5] TXD[3:0] TXD[7:4] TXD[4] TXEN TXD[9] TXERR tSKRGT TX_CLK (At PHY) TX_CTL RXD[8:5][3:0] RXD[7:4][3:0] RXD[8:5] RXD[3:0] RXD[7:4] tSKRGT RXD[4] RXDV RXD[9] RXERR tSKRGT RX_CTL RX_CLK (At PHY) Figure 13. RGMII and RTBI AC Timing and Multiplexing Diagrams MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 29 Ethernet: Three-Speed Ethernet, MII Management 8.3 Ethernet Management Interface Electrical Characteristics The electrical characteristics specified here apply to MII management interface signals MDIO (management data input/output) and MDC (management data clock). The electrical characteristics for MII, RMII, RGMII, SGMII, and RTBI are specified in Section 8.1, “Enhanced Three-Speed Ethernet Controller (eTSEC) (10/100/1000 Mbps)—MII/RMII/RGMII/SGMII/RTBI Electrical Characteristics.” 8.3.1 MII Management DC Electrical Characteristics The MDC and MDIO are defined to operate at a supply voltage of 2.5V or 3.3 V. The DC electrical characteristics for MDIO and MDC are provided in Table 29 and Table 30. Table 29. MII Management DC Electrical Characteristics When Powered at 2.5 V Parameter Symbol Conditions — IOH = –1.0 mA NVDDA or NV DDB = M in Min 2.37 2.00 Max 2.63 NVDDA + 0.3 or NVDDB + 0.3 0.40 — 0.70 10 — Unit V V Supply voltage (2.5 V) NV DDA/NVDDB Output high voltage VOH Output low voltage Input high voltage Input low voltage Input high current Input low current VOL VIH VIL IIH IIL IOL = 1.0 mA — — NVDDA or NV DDB = M in NVDDA or NV DDB = M in NVDDA or NV DDB = M in VSS – 0.3 1.7 –0.3 — –15 V V V μA μA VIN 1 = NVDDA or NVDDB VIN = NVDDA or NV DDB Note: 1. Note that the symbol VIN, in this case, represents the LVIN symbol referenced in Table 1 and Table 2. Table 30. MII Management DC Electrical Characteristics When Powered at 3.3 V Parameter Symbol Conditions — IOH = –1.0 mA NVDDA or NVDDB = Min Min 2.97 2.10 Max 3.63 NVDDA + 0.3 or NVDDB + 0.3 0.50 — 0.80 40 — Unit V V Supply voltage (3.3 V) NVDDA/NVDDB Output high voltage VOH Output low voltage Input high voltage Input low voltage Input high current Input low current VOL VIH VIL IIH IIL IOL = 1.0 mA — — NVDDA or NVDDB = Max NVDDA or NVDDB = Max LVDDA or LVDDB = Min VSS 2.00 — V V V μA μA VIN 1 = 2.1 V VIN = 0.5 V — –600 Note: 1. Note that the symbol VIN, in this case, represents the LVIN symbol referenced in Table 1 and Table 2. MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 30 Freescale Semiconductor Ethernet: Three-Speed Ethernet, MII Management 8.3.2 MII Management AC Electrical Specifications Table 31. MII Management AC Timing Specifications Table 31 provides the MII management AC timing specifications. At recommended operating conditions with LVDDA/LVDDB is 3.3 V ± 10% or 2.5 V ± 5% Parameter/Condition MDC frequency MDC period MDC clock pulse width high MDC to MDIO delay MDIO to MDC setup time MDIO to MDC hold time MDC rise time MDC fall time Symbol 1 fMDC tMDC tMDCH tMDKHDX tMDDVKH tMDDXKH tMDCR tMDHF Min — — 32 10 5 0 — — Typ 2.5 400 — — — — — — Max — — — 170 — — 10 10 Unit MHz ns ns ns ns ns ns ns Notes 2 Notes: 1. The symbols used for timing specifications herein follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tMDKHDX symbolizes management data timing (MD) for the time tMDC from clock reference (K) high (H) until data outputs (D) are invalid (X) or data hold time. Also, tMDDVKH symbolizes management data timing (MD) with respect to the time data input signals (D) reach the valid state (V) relative to the tMDC clock reference (K) going to the high (H) state or setup time. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall). Figure 14 shows the MII management AC timing diagram. tMDC MDC tMDCH MDIO (Input) tMDDVKH tMDDXKH MDIO (Output) tMDKHDX tMDCF tMDCR Figure 14. MII Management Interface Timing Diagram MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 31 Ethernet: Three-Speed Ethernet, MII Management 8.3.3 SGMII DC Electrical Characteristics The SGMII Solution in the MPC8313 is designed to be used in a 4-wire AC-Coupled SGMII link. Table 32 andTable 33describe the SGMII AC-Coupled DC electrical characteristics. Transmitter characteristics are measured at the transmitter outputs, SD_TX and SD_TX_B as depicted in Figure 15. Table 32. DC Transmitter Electrical Characteristics Parameter Output high voltage Output low voltage Symbol VOH VOL VRING |VOD| VOS (XPADVDD/2)/1.7 0.3*XPADVDD Min Max 0.7*XPADVDD1 Unit mV mV Will not align to DC-coupled SGMII Notes Output ringing Output differential voltage Output offset voltage 10 (XPADVDD/2)/1.3 % mV mV Will not align to DC-coupled SGMII (XPADVDD/2) – 50 mV (XPADVDD/2) + 50 mV Output impedance (single ended) Mismatch in a pair Change in VOD between “0” and “1” Change in VOS between “0” and “1” Output current on short to GND 1 XPADVDDrefers RO ΔRO Δ|VOD| Δ VOS ISA, ISB 40 60 10 25 25 40 Ω % mV mV mA to the SGMII transmitter output supply voltage. SD_TX Transmitter 100 ohms SD_TX_B Figure 15. Transmitter Reference Circuit MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 32 Freescale Semiconductor Ethernet: Three-Speed Ethernet, MII Management Table 33. DC Receiver Electrical Characteristics Parameter DC input voltage range Input differential voltage Loss of signal threshold Input AC common mode voltage Receiver differential input impedance Receiver common mode input impedance Common mode input voltage Vrx_diffpp Vlos Vcm_acpp Zrx_diff Zrx_cm Vcm 80 20 xcorevss 100 30 1200 100 100 120 35 xcorevss Symbol Min Max Unit Notes Input must be externally ac-coupled. mV Peak to peak input differential voltage. mV mV Peak to peak ac common mode voltage. Ω Ω V On-chip termination to xcorevss. 8.3.3.1 SGMII Transmit AC Timing Specifications Table 34. SGMII Transmit AC Timing Specifications Parameter Symbol JD JT UI tfall trise 800 50 50 Min Max 0.17 0.35 800 120 120 Unit UI p-p UI p-p ps ps ps +/– 100ppm Notes Table 34 provides the SGMII transmit AC timing targets. A source synchronous clock is not provided. Deterministic Jitter Total Jitter Unit Interval VOD fall time (80%–20%) VOD rise time (20%–80%) Source synchronous clock is not supported MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 33 Ethernet: Three-Speed Ethernet, MII Management 8.3.3.2 SGMII Receive AC Timing Specifications Table 35. SGMII Receiver AC Timing Specifications Parameter Symbol JD JDR Min 0.37 0.55 Max Unit UI p-p UI p-p Notes Measured at receiver Measured at receiver Table 35 provides the SGMII transmit AC timing targets. A source synchronous clock is not supported. Deterministic Jitter Tolerance Combined Deterministic and Random Jitter Tolerance Sinusoidal Jitter Tolerance Jsin 0.1 UI p-p Measured at receiver Total Jitter Tolerance Bit Error Ratio Unit Interval JT BER UI 0.65 10-12 800 800 UI p-p Measured at receiver ps +/– 100ppm Vrx_diffpp_max/2 Vrx_diffpp_min/2 0 –Vrx_diffpp_min/2 –Vrx_diffpp_max/2 0 .275 .4 .6 Time (UI) .625 1 Figure 16. Receive Input Compliance Mask MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 34 Freescale Semiconductor USB 9 9.1 USB USB Dual-Role Controllers This section provides the AC and DC electrical specifications for the USB interface. 9.1.1 USB DC Electrical Characteristics Table 36. USB DC Electrical Characteristics Parameter Symbol VIH VIL IIN VOH VOL Min 2 –0.3 — LV DDB – 0.2 — Max LVDDB+ 0.3 0.8 ±5 — 0.2 Unit V V μA V V Table 36 provides the DC electrical characteristics for the USB interface. High-level input voltage Low-level input voltage Input current High-level output voltage, IOH = –100 μA Low-level output voltage, IOL = 100 μA 9.1.2 USB AC Electrical Specifications Table 37. USB General Timing Parameters Parameter Symbol 1 tUSCK tUSIVKH tUSIXKH tUSKHOV tUSKHOX Min 15 4 0 — 2 Max — — — 7 — Unit ns ns ns ns ns Notes Table 37 describes the general timing parameters of the USB interface. USB clock cycle time Input setup to USB clock - all inputs input hold to USB clock - all inputs USB clock to output valid - all outputs Output hold from USB clock - all outputs Note: 1. The symbols used for timing specifications herein follow the pattern of t(First two letters of functional block)(signal)(state) (reference)(state) for inputs and t(First two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tUSIXKH symbolizes USB timing (USB) for the input (I) to go invalid (X) with respect to the time the USB clock reference (K) goes high (H). Also, t USKHOX symbolizes us timing (USB) for the USB clock reference (K) to go high (H), with respect to the output (O) going invalid (X) or output hold time. MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 35 USB Figure 17 and Figure 18 provide the AC test load and signals for the USB, respectively. Output Z0 = 50 Ω RL = 5 0 Ω NVDD/2 Figure 17. USB AC Test Load USB0_CLK/USB1_CLK/DR_CLK tUSIVKH Input Signals tUSIXKH tUSKHOV Output Signals: tUSKHOX Figure 18. USB Signals 9.2 On-Chip USB PHY See chapter 7 in the USB Specifications Rev 2.0 MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 36 Freescale Semiconductor Local Bus 10 Local Bus This section describes the DC and AC electrical specifications for the local bus interface. 10.1 Local Bus DC Electrical Characteristics Table 38 provides the DC electrical characteristics for the local bus interface. Table 38. Local Bus DC Electrical Characteristics at 3.3 V Parameter High-level input voltage Low-level input voltage Input current (VIN1 = 0 V or VIN = LV DD) High-level output voltage, (LVDD = min, IOH = -2 mA) Low-level output voltage, (LVDD = min, IOH = 2 mA) Symbol VIH VIL IIN VOH VOL Min 2 –0.3 — Max LVDD + 0.3 0.8 ±5 Unit V V μA V V LVDD – 0.2 — — 0.2 10.2 Local Bus AC Electrical Specifications Table 39. Local Bus General Timing Parameters Parameter Symbol 1 tLBK tLBIVKH tLBIXKH tLBOTOT1 tLBOTOT2 tLBOTOT3 Min 15 7 1.0 1.5 3 2.5 Max — — — — — — Unit ns ns ns ns ns ns Notes 2 3, 4 3, 4 5 6 7 Table 39 describes the general timing parameters of the local bus interface. Local bus cycle time Input setup to local bus clock Input hold from local bus clock LALE output fall to LAD output transition (LATCH hold time) LALE output fall to LAD output transition (LATCH hold time) LALE output fall to LAD output transition (LATCH hold time) MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 37 Local Bus Table 39. Local Bus General Timing Parameters (continued) Parameter Local bus clock to output valid Local bus clock to output high impedance for LAD Symbol 1 tLBKHOV tLBKHOZ Min — — Max 3 4 Unit ns ns Notes 3 8 Notes: 1. The symbols used for timing specifications herein follow the pattern of t(First two letters of functional block)(signal)(state) (reference)(state) for inputs and t(First two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tLBIXKH1 symbolizes local bus timing (LB) for the input (I) to go invalid (X) with respect to the time the tLBK clock reference (K) goes high (H), in this case for clock one(1). 2. All timings are in reference to falling edge of LCLK0 (for all outputs and for LGTA and LUPWAIT inputs) or rising edge of LCLK0 (for all other inputs). 3. All signals are measured from NVDD/2 of the rising/falling edge of LCLK0 to 0.4 × NVDD of the signal in question for 3.3-V signaling levels. 4. Input timings are measured at the pin. 5.tLBOTOT1 should be used when RCWH[LALE] is not set and the load on LALE output pin is at least 10pF less than the load on LAD output pins. 6.tLBOTOT2 should be used when RCWH[LALE] is set and the load on LALE output pin is at least 10pF less than the load on LAD output pins. 7.tLBOTOT3 should be used when RCWH[LALE] is set and the load on LALE output pin equals to the load on LAD output pins. 8. For purposes of active/float timing measurements, the Hi-Z or off state is defined to be when the total current delivered through the component pin is less than or equal to the leakage current specification. Figure 19 provides the AC test load for the local bus. Output Z0 = 50 Ω RL = 5 0 Ω NVDD/2 Figure 19. Local Bus AC Test Load MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 38 Freescale Semiconductor Local Bus Figure 20 through Figure 22 show the local bus signals. LCLK[n] tLBIVKH Input Signals: LAD[0:15] tLBIVKH Input Signal: LGTA tLBIXKH Output Signals: tLBKHOV tLBIXKH tLBIXKH LBCTL/LBCKE/LOE/ Output Signals: LAD[0:15] tLBKHOV tLBKHOZ tLBOTOT LALE Figure 20. Local Bus Signals, Non-Special Signals Only MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 39 Local Bus LCLK T1 T3 tLBKHOV GPCM Mode Output Signals: LCS[0:3]/LWE tLBIVKH UPM Mode Input Signal: LUPWAIT tLBIVKH tLBIXKH tLBIXKH tLBKHOZ Input Signals: LAD[0:15] tLBKHOV UPM Mode Output Signals: LCS[0:3]/LBS[0:1]/LGPL[0:5] tLBKHOZ Figure 21. Local Bus Signals, GPCM/UPM Signals for LCCR[CLKDIV] = 2 MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 40 Freescale Semiconductor Local Bus LCLK T1 T2 T3 T4 tLBKHOV GPCM Mode Output Signals: LCS[0:3]/LWE tLBIVKH UPM Mode Input Signal: LUPWAIT tLBIVKH tLBIXKH tLBIXKH tLBKHOZ Input Signals: LAD[0:15] tLBKHOV UPM Mode Output Signals: LCS[0:3]/LBS[0:1]/LGPL[0:5] tLBKHOZ Figure 22. Local Bus Signals, GPCM/UPM Signals for LCCR[CLKDIV] = 4 MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 41 JTAG 11 JTAG This section describes the DC and AC electrical specifications for the IEEE Std. 1149.1 (JTAG) interface. 11.1 JTAG DC Electrical Characteristics Table 40. JTAG Interface DC Electrical Characteristics Characteristic Input high voltage Input low voltage Input current Output high voltage Output low voltage Output low voltage Symbol VIH VIL IIN VOH VOL VOL IOH = –8.0 mA IOL = 8.0 mA IOL = 3.2 mA 2.4 — — Condition Min 2.0 –0.3 Max NVDD + 0.3 0.8 ±5 — 0.5 0.4 Unit V V μA V V V Table 40 provides the DC electrical characteristics for the IEEE Std. 1149.1 (JTAG) interface. 11.2 JTAG AC Timing Specifications This section describes the AC electrical specifications for the IEEE Std. 1149.1 (JTAG) interface. Table 41 provides the JTAG AC timing specifications as defined in Figure 24 through Figure 27. Table 41. JTAG AC Timing Specifications (Independent of SYS_CLK_IN) 1 At recommended operating conditions (see Table 2). Parameter JTAG external clock frequency of operation JTAG external clock cycle time JTAG external clock pulse width measured at 1.4 V JTAG external clock rise and fall times TRST assert time Input setup times: Boundary-scan data TMS, TDI Input hold times: Boundary-scan data TMS, TDI Valid times: Boundary-scan data TDO Output hold times: Boundary-scan data TDO Symbol 2 fJTG t JTG tJTKHKL tJTGR & tJTGF tTRST tJTDVKH tJTIVKH tJTDXKH tJTIXKH tJTKLDV tJTKLOV tJTKLDX tJTKLOX Min 0 30 15 0 25 4 4 Max 33.3 — — 2 — — — Unit MHz ns ns ns ns ns Notes 3 4 ns 10 10 — — ns 2 2 11 11 5 4 2 2 — — ns 5 MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 42 Freescale Semiconductor JTAG Table 41. JTAG AC Timing Specifications (Independent of SYS_CLK_IN) 1 (continued) At recommended operating conditions (see Table 2). Parameter JTAG external clock to output high impedance: Boundary-scan data TDO Symbol 2 Min Max Unit Notes tJTKLDZ tJTKLOZ 2 2 19 9 ns 5, 6 Notes: 1. All outputs are measured from the midpoint voltage of the falling/rising edge of tTCLK to the midpoint of the signal in question. The output timings are measured at the pins. All output timings assume a purely resistive 50-Ω load (see Figure 17). Time-of-flight delays must be added for trace lengths, vias, and connectors in the system. 2. The symbols used for timing specifications herein follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tJTDVKH symbolizes JTAG device timing (JT) with respect to the time data input signals (D) reaching the valid state (V) relative to the tJTG clock reference (K) going to the high (H) state or setup time. Also, tJTDXKH symbolizes JTAG timing (JT) with respect to the time data input signals (D) went invalid (X) relative to the tJTG clock reference (K) going to the high (H) state. Note that, in general, the clock reference symbol representation is based on three letters representing the clock of a particular functional. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall). 3. TRST is an asynchronous level sensitive signal. The setup time is for test purposes only. 4. Non-JTAG signal input timing with respect to tTCLK. 5. Non-JTAG signal output timing with respect to tTCLK. 6. Guaranteed by design and characterization. Figure 23 provides the AC test load for TDO and the boundary-scan outputs. Output Z0 = 50 Ω R L = 50 Ω NVDD/2 Figure 23. AC Test Load for the JTAG Interface Figure 24 provides the JTAG clock input timing diagram. JTAG External Clock VM tJTKHKL tJTG VM = Midpoint Voltage (NV DD/2) VM VM tJTGR tJTGF Figure 24. JTAG Clock Input Timing Diagram Figure 25 provides the TRST timing diagram. TRST VM tTRST VM = Midpoint Voltage (NVDD/2) VM Figure 25. TRST Timing Diagram MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 43 JTAG Figure 26 provides the boundary-scan timing diagram. JTAG External Clock VM tJTDVKH tJTDXKH Boundary Data Inputs tJTKLDV tJTKLDX Boundary Data Outputs tJTKLDZ Boundary Data Outputs Output Data Valid VM = Midpoint Voltage (NVDD /2) Output Data Valid Input Data Valid VM Figure 26. Boundary-Scan Timing Diagram Figure 27 provides the test access port timing diagram. JTAG External Clock VM tJTIVKH tJTIXKH TDI, TMS tJTKLOV tJTKLOX TDO tJTKLOZ TDO Output Data Valid VM = Midpoint Voltage (NVDD/2) Output Data Valid Input Data Valid VM Figure 27. Test Access Port Timing Diagram MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 44 Freescale Semiconductor I2C 12 I2C This section describes the DC and AC electrical characteristics for the I2C interface. 12.1 I2C DC Electrical Characteristics Table 42. I2C DC Electrical Characteristics Table 42 provides the DC electrical characteristics for the I2C interface. At recommended operating conditions with NVDD of 3.3 V ± 10%. Parameter Input high voltage level Input low voltage level Low level output voltage Output fall time from VIH(min) to VIL(max) with a bus capacitance from 10 to 400 pF Pulse width of spikes which must be suppressed by the input filter Capacitance for each I/O pin Input current (0 V ≤VIN ≤ NVDD) Symbol VIH VIL VOL tI2KLKV tI2KHKL CI IIN Min 0.7 × NVDD –0.3 0 20 + 0.1 × CB 0 — — Max NVDD + 0.3 0.3 × NVDD 0.2 × NVDD 250 50 10 ±5 Unit V V V ns ns pF μA Notes 1 2 3 4 Notes: 1. Output voltage (open drain or open collector) condition = 3 mA sink current. 2. CB = capacitance of one bus line in pF. 3. Refer to the MPC8313E PowerQUICC II Pro Integrated Host Processor Reference Manual for information on the digital filter used. 4. I/O pins will obstruct the SDA and SCL lines if NVDD is switched off. 12.2 I2C AC Electrical Specifications Table 43. I2C AC Electrical Specifications Table 43 provides the AC timing parameters for the I2C interface. All values refer to VIH (min) and VIL (max) levels (see Table 42). Parameter SCL clock frequency Low period of the SCL clock High period of the SCL clock Setup time for a repeated START condition Hold time (repeated) START condition (after this period, the first clock pulse is generated) Data setup time Symbol 1 fI2C tI2CL tI2CH tI2SVKH tI2SXKL tI2DVKH Min 0 1.3 0.6 0.6 0.6 100 Max 400 — — — — — Unit kHz μs μs μs μs ns MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 45 I2C Table 43. I2C AC Electrical Specifications (continued) All values refer to VIH (min) and VIL (max) levels (see Table 42). Parameter Data hold time: CBUS compatible masters I2C bus devices Rise time of both SDA and SCL signals Fall time of both SDA and SCL signals Setup time for STOP condition Bus free time between a STOP and START condition Noise margin at the LOW level for each connected device (including hysteresis) Noise margin at the HIGH level for each connected device (including hysteresis) Symbol 1 tI2DXKL Min Max Unit μs — 02 tI2CR 20 + 0.1 CB 4 20 + 0.1 CB 0.6 1.3 0.1 × NVDD 0.2 × NVDD 4 — 0.9 3 300 300 — — — — ns ns μs μs V V tI2CF tI2PVKH tI2KHDX VNL VNH Notes: 1. The symbols used for timing specifications herein follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tI2DVKH symbolizes I2C timing (I2) with respect to the time data input signals (D) reach the valid state (V) relative to the tI2C clock reference (K) going to the high (H) state or setup time. Also, tI2SXKL symbolizes I2C timing (I2) for the time that the data with respect to the start condition (S) went invalid (X) relative to the tI2C clock reference (K) going to the low (L) state or hold time. Also, tI2PVKH symbolizes I2C timing (I2) for the time that the data with respect to the stop condition (P) reaching the valid state (V) relative to the tI2C clock reference (K) going to the high (H) state or setup time. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall). 2. The MPC8313E provides a hold time of at least 300 ns for the SDA signal (referred to the VIHmin of the SCL signal) to bridge the undefined region of the falling edge of SCL. 3. The maximum tI2DVKH has only to be met if the device does not stretch the LOW period (tI2CL) of the SCL signal. 4. CB = capacitance of one bus line in pF. Figure 28 provides the AC test load for the I2C. Output Z0 = 50 Ω RL = 5 0 Ω NVDD/2 Figure 28. I2C AC Test Load MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 46 Freescale Semiconductor I2C Figure 29 shows the AC timing diagram for the I2C bus. SDA tI2CF tI2CL SCL tI2SXKL S tI2DXKL tI2CH Sr tI2SVKH tI2PVKH P S tI2DVKH tI2SXKL tI2KHKL tI2CR tI2CF Figure 29. I2C Bus AC Timing Diagram MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 47 PCI 13 PCI This section describes the DC and AC electrical specifications for the PCI bus. 13.1 PCI DC Electrical Characteristics Table 44. PCI DC Electrical Characteristics 1 Parameter Symbol VIH VIL VOH VOL IIN Test Condition VOUT ≥ VOH (min) or VOUT ≤ VOL (max) NVDD = min, IOH = –100 μA NVDD = min, IOL = 100 μA 0 V ≤ VIN ≤ NVDD Min 0.5 x NVDD –0.5 0.9 x NVDD — — Max NVDD + 0.3 0.3 x NVDD — 0.1x NVDD ±5 Unit V V V V μA Table 44 provides the DC electrical characteristics for the PCI interface. High-level input voltage Low-level input voltage High-level output voltage Low-level output voltage Input current Note: 1. Note that the symbol V IN, in this case, represents the OVIN symbol referenced in Table 1 and Table 2. 13.2 PCI AC Electrical Specifications This section describes the general AC timing parameters of the PCI bus. Note that the PCI_CLK or PCI_SYNC_IN signal is used as the PCI input clock depending on whether the MPC8313E is configured as a host or agent device. Table 45 shows the PCI AC timing specifications at 66 MHz. . Table 45. PCI AC Timing Specifications at 66 MHz Parameter Symbol 1 tPCKHOV Min — 1 — 3.0 0 Max 6.0 — 14 — — Unit ns ns ns ns ns Notes 2 2 2, 3 2, 4 2, 4 Clock to output valid Output hold from Clock Clock to output high impedance Input setup to Clock Input hold from Clock tPCKHOX tPCKHOZ tPCIVKH tPCIXKH Notes: 1. Note that the symbols used for timing specifications herein follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tPCIVKH symbolizes PCI timing (PC) with respect to the time the input signals (I) reach the valid state (V) relative to the PCI_SYNC_IN clock, tSYS, reference (K) going to the high (H) state or setup time. Also, tPCRHFV symbolizes PCI timing (PC) with respect to the time hard reset (R) went high (H) relative to the frame signal (F) going to the valid (V) state. 2. See the timing measurement conditions in the PCI 2.3 Local Bus Specifications. 3. For purposes of active/float timing measurements, the Hi-Z or off state is defined to be when the total current delivered through the component pin is less than or equal to the leakage current specification. 4. Input timings are measured at the pin. MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 48 Freescale Semiconductor PCI Table 46 shows the PCI AC Timing Specifications at 33 MHz. Table 46. PCI AC Timing Specifications at 33 MHz Parameter Clock to output valid Output hold from Clock Clock to output high impedance Input setup to Clock Input hold from Clock Symbol 1 tPCKHOV Min — 2 — 3.0 0 Max 11 — 14 — — Unit ns ns ns ns ns Notes 2 2 2, 3 2, 4 2, 4 tPCKHOX tPCKHOZ tPCIVKH tPCIXKH Notes: 1. Note that the symbols used for timing specifications herein follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tPCIVKH symbolizes PCI timing (PC) with respect to the time the input signals (I) reach the valid state (V) relative to the PCI_SYNC_IN clock, tSYS, reference (K) going to the high (H) state or setup time. Also, tPCRHFV symbolizes PCI timing (PC) with respect to the time hard reset (R) went high (H) relative to the frame signal (F) going to the valid (V) state. 2. See the timing measurement conditions in the PCI 2.3 Local Bus Specifications. 3. For purposes of active/float timing measurements, the Hi-Z or off state is defined to be when the total current delivered through the component pin is less than or equal to the leakage current specification. 4. Input timings are measured at the pin. Figure 30 provides the AC test load for PCI. Output Z0 = 50 Ω RL = 5 0 Ω NVDD/2 Figure 30. PCI AC Test Load Figure 31 shows the PCI input AC timing conditions. CLK tPCIVKH tPCIXKH Input Figure 31. PCI Input AC Timing Measurement Conditions MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 49 PCI Figure 32 shows the PCI output AC timing conditions. CLK tPCKHOV Output Delay tPCKHOZ High-Impedance Output tPCKHOX Figure 32. PCI Output AC Timing Measurement Condition MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 50 Freescale Semiconductor Timers 14 Timers This section describes the DC and AC electrical specifications for the timers. 14.1 Timers DC Electrical Characteristics Table 47 provides the DC electrical characteristics for the MPC8313E timers pins, including TIN, TOUT, TGATE, and RTC_CLK. Table 47. Timers DC Electrical Characteristics Characteristic Output high voltage Output low voltage Output low voltage Input high voltage Input low voltage Input current Symbol VOH VOL VOL VIH VIL IIN Condition IOH = –8.0 mA IOL = 8.0 mA IOL = 3.2 mA — — 0 V ≤ VIN ≤ NVDD Min 2.4 — — 2.0 –0.3 — Max — 0.5 0.4 NVDD + 0.3 0.8 ±5 Unit V V V V V μA 14.2 Timers AC Timing Specifications Table 48. Timers Input AC Timing Specifications 1 Characteristic Symbol 2 tTIWID Min 20 Unit ns Table 48 provides the Timers input and output AC timing specifications. Timers inputs—minimum pulse width Notes: 1. Input specifications are measured from the 50% level of the signal to the 50% level of the rising edge of SYS_CLK_IN. Timings are measured at the pin. 2. Timers inputs and outputs are asynchronous to any visible clock. Timers outputs should be synchronized before use by any external synchronous logic. Timers inputs are required to be valid for at least tTIWID ns to ensure proper operation Figure 33 provides the AC test load for the Timers. Output Z0 = 50 Ω RL = 5 0 Ω NVDD/2 Figure 33. Timers AC Test Load MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 51 GPIO 15 GPIO This section describes the DC and AC electrical specifications for the GPIO. 15.1 GPIO DC Electrical Characteristics Table 49. GPIO DC Electrical Characteristics Characteristic Output high voltage Output low voltage Output low voltage Input high voltage Input low voltage Input current Symbol VOH VOL VOL VIH VIL IIN Condition IOH = –8.0 mA IOL = 8.0 mA IOL = 3.2 mA — — 0 V ≤ VIN ≤ NVDD Min 2.4 — — 2.0 –0.3 — Max — 0.5 0.4 NVDD + 0.3 0.8 ±5 Unit V V V V V μA Table 49 provides the DC electrical characteristics for the GPIO. 15.2 GPIO AC Timing Specifications Table 50. GPIO Input AC Timing Specifications 1 Characteristic Symbol 2 tPIWID Min 20 Unit ns Table 50 provides the GPIO input and output AC timing specifications. GPIO inputs—minimum pulse width Notes: 1. Input specifications are measured from the 50% level of the signal to the 50% level of the rising edge of SYS_CLKIN. Timings are measured at the pin. 2. GPIO inputs and outputs are asynchronous to any visible clock. GPIO outputs should be synchronized before use by any external synchronous logic. GPIO inputs are required to be valid for at least tPIWID ns to ensure proper operation. Figure 34 provides the AC test load for the GPIO. Output Z0 = 50 Ω RL = 5 0 Ω NVDD/2 Figure 34. GPIO AC Test Load MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 52 Freescale Semiconductor IPIC 16 IPIC This section describes the DC and AC electrical specifications for the external interrupt pins. 16.1 IPIC DC Electrical Characteristics Table 51. IPIC DC Electrical Characteristics Characteristic Input high voltage Input low voltage Input current Output low voltage Output low voltage Symbol VIH VIL IIN VOL VOL IOL = 8.0 mA IOL = 3.2 mA — — Condition Min 2.0 –0.3 Max NVDD + 0.3 0.8 ±5 0.5 0.4 Unit V V μA V V Table 51 provides the DC electrical characteristics for the external interrupt pins. 16.2 IPIC AC Timing Specifications Table 52. IPIC Input AC Timing Specifications 1 Characteristic Symbol 2 tPIWID Min 20 Unit ns Table 52 provides the IPIC input and output AC timing specifications. IPIC inputs—minimum pulse width Notes: 1. Input specifications are measured from the 50% level of the signal to the 50% level of the rising edge of SYS_CLK_IN. Timings are measured at the pin. 2. IPIC inputs and outputs are asynchronous to any visible clock. IPIC outputs should be synchronized before use by any external synchronous logic. IPIC inputs are required to be valid for at least tPIWID ns to ensure proper operation when working in edge triggered mode. MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 53 SPI 17 SPI This section describes the DC and AC electrical specifications for the SPI of the MPC8313E 17.1 SPI DC Electrical Characteristics Table 53 provides the DC electrical characteristics for the MPC8313E SPI. Table 53. SPI DC Electrical Characteristics Characteristic Output high voltage Output low voltage Output low voltage Input high voltage Input low voltage Input current Symbol VOH VOL VOL VIH VIL IIN Condition IOH = –6.0 mA IOL = 6.0 mA IOL = 3.2 mA — — 0 V ≤ VIN ≤ OVDD Min 2.4 — — 2.0 –0.3 — Max — 0.5 0.4 OVDD + 0.3 0.8 ±5 Unit V V V V V μA 17.2 SPI AC Timing Specifications Table 54 and provide the SPI input and output AC timing specifications. Table 54. SPI AC Timing Specifications 1 Characteristic SPI outputs—Master mode (internal clock) delay SPI outputs—Slave mode (external clock) delay SPI inputs—Master mode (internal clock) input setup time SPI inputs—Master mode (internal clock) input hold time SPI inputs—Slave mode (external clock) input setup time SPI inputs—Slave mode (external clock) input hold time Symbol 2 tNIKHOV tNEKHOV tNIIVKH tNIIXKH tNEIVKH tNEIXKH Min 0.5 2 6 0 4 2 Max 6 8 Unit ns ns ns ns ns ns Notes: 1. Output specifications are measured from the 50% level of the rising edge of SYS_CLK_IN to the 50% level of the signal. Timings are measured at the pin. 2. The symbols used for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tNIKHOV symbolizes the NMSI outputs internal timing (NI) for the time tSPI memory clock reference (K) goes from the high state (H) until outputs (O) are valid (V). MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 54 Freescale Semiconductor SPI Figure 35 provides the AC test load for the SPI. Output Z0 = 50 Ω RL = 5 0 Ω OVDD/2 Figure 35. SPI AC Test Load Figure 36 through Figure 37 represent the AC timing from Table 54. Note that although the specifications generally reference the rising edge of the clock, these AC timing diagrams also apply when the falling edge is the active edge. Figure 36 shows the SPI timing in Slave mode (external clock). SPICLK (input) tNEIVKH tNEIXKH Input Signals: SPIMOSI (See Note) Output Signals: SPIMISO (See Note) tNEKHOV Note: The clock edge is selectable on SPI. Figure 36. SPI AC Timing in Slave Mode (External Clock) Diagram Figure 37 shows the SPI timing in Master mode (internal clock). SPICLK (output) tNIIVKH tNIIXKH Input Signals: SPIMISO (See Note) Output Signals: SPIMOSI (See Note) tNIKHOV Note: The clock edge is selectable on SPI. Figure 37. SPI AC Timing in Master Mode (Internal Clock) Diagram MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 55 Package and Pin Listings 18 Package and Pin Listings This section details package parameters, pin assignments, and dimensions. The MPC8313E is available in a thermally enhanced plastic ball grid array (TEPBGAII), see Section 18.1, “Package Parameters for the MPC8313E TEPBGAII,” and Section 18.2, “Mechanical Dimensions of the MPC8313E TEPBGAII,” for information on the TEPBGAII. 18.1 Package Parameters for the MPC8313E TEPBGAII The package parameters are as provided in the following list. The package type is 27 mm × 27 mm, 516 TEPBGAII. Package outline 27 mm × 27 mm Interconnects 516 Pitch 1.00 mm Module height (typical) 2.25 mm Solder Balls 95.5 Sn/0.5 Cu/4Ag (VR package) Ball diameter (typical) 0.6 mm 18.2 Mechanical Dimensions of the MPC8313E TEPBGAII Figure 38 shows the mechanical dimensions and bottom surface nomenclature of the 516-TEPBGAII package. MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 56 Freescale Semiconductor Package and Pin Listings Figure 38. Mechanical Dimension and Bottom Surface Nomenclature of the MPC8313E TEPBGAII 1. 2. 3. 4. 5. All dimensions are in millimeters. Dimensions and tolerances per ASME Y14.5M-1994. Maximum solder ball diameter measured parallel to datum A. Datum A, the seating plane, is determined by the spherical crowns of the solder balls. Package code 5368 is to account for PGE and the built–in heat spreader. MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 57 Package and Pin Listings 18.3 Pinout Listings Table 55. MPC8313E TEPBGAII Pinout Listing Signal Package Pin Number DDR Memory Controller Interface Pin Type Power Supply Notes Table 55 provides the pin-out listing for the MPC8313E, TEPBGAII package. MEMC_MDQ[0] MEMC_MDQ[1] MEMC_MDQ[2] MEMC_MDQ[3] MEMC_MDQ[4] MEMC_MDQ[5] MEMC_MDQ[6] MEMC_MDQ[7] MEMC_MDQ[8] MEMC_MDQ[9] MEMC_MDQ[10] MEMC_MDQ[11] MEMC_MDQ[12] MEMC_MDQ[13] MEMC_MDQ[14] MEMC_MDQ[15] MEMC_MDQ[16] MEMC_MDQ[17] MEMC_MDQ[18] MEMC_MDQ[19] MEMC_MDQ[20] MEMC_MDQ[21] MEMC_MDQ[22] MEMC_MDQ[23] MEMC_MDQ[24] MEMC_MDQ[25] MEMC_MDQ[26] MEMC_MDQ[27] MEMC_MDQ[28] MEMC_MDQ[29] A8 A9 C10 C9 E9 E11 E10 C8 E8 A6 B6 C6 C7 D7 D6 A5 A19 D18 A17 E17 E16 C18 D19 C19 E19 A22 C21 C20 A21 A20 IO IO IO IO IO IO IO IO IO IO IO IO IO IO IO IO IO IO IO IO IO IO IO IO IO IO IO IO IO IO GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 58 Freescale Semiconductor Package and Pin Listings Table 55. MPC8313E TEPBGAII Pinout Listing (continued) Signal MEMC_MDQ[30] MEMC_MDQ[31] MEMC_MDM0 MEMC_MDM1 MEMC_MDM2 MEMC_MDM3 MEMC_MDQS[0] MEMC_MDQS[1] MEMC_MDQS[2] MEMC_MDQS[3] MEMC_MBA[0] MEMC_MBA[1] MEMC_MBA[2] MEMC_MA0 MEMC_MA1 MEMC_MA2 MEMC_MA3 MEMC_MA4 MEMC_MA5 MEMC_MA6 MEMC_MA7 MEMC_MA8 MEMC_MA9 MEMC_MA10 MEMC_MA11 MEMC_MA12 MEMC_MA13 MEMC_MA14 MEMC_MWE MEMC_MRAS MEMC_MCAS MEMC_MCS[0] MEMC_MCS[1] MEMC_MCKE Package Pin Number C22 B22 B7 E6 E18 E20 A7 E7 B19 A23 D15 A18 A15 E12 D11 B11 A11 A12 E13 C12 E14 B15 C17 C13 A16 C15 C16 E15 B18 C11 B10 D10 A10 B14 Pin Type IO IO O O O O IO IO IO IO O O O O O O O O O O O O O O O O O O O O O O O O Power Supply GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD 3 Notes MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 59 Package and Pin Listings Table 55. MPC8313E TEPBGAII Pinout Listing (continued) Signal MEMC_MCK MEMC_MCK MEMC_MODT[0] MEMC_MODT[1] Package Pin Number A13 A14 B23 C23 Local Bus Controller Interface LAD0 LAD1 LAD2 LAD3 LAD4 LAD5 LAD6 LAD7 LAD8 LAD9 LAD10 LAD11 LAD12 LAD13 LAD14 LAD15 LA16 LA17 LA18 LA19 LA20 LA21 LA22 LA23 LA24 LA25 LCS[0] LCS[1] LCS[2] K25 K24 K23 K22 J25 J24 J23 J22 H24 F26 G24 F25 E25 F24 G22 F23 AC25 AC26 AB22 AB23 AB24 AB25 AB26 E22 E23 D22 D23 J26 F22 IO IO IO IO IO IO IO IO IO IO IO IO IO IO IO IO O O O O O O O O O O O O O LVDD LVDD LVDD LVDD LVDD LVDD LVDD LVDD LVDD LVDD LVDD LVDD LVDD LVDD LVDD LVDD LVDD LVDD LVDD LVDD LVDD LVDD LVDD LVDD LVDD LVDD LVDD LVDD LVDD Pin Type O O O O Power Supply GVDD GVDD GVDD GVDD Notes MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 60 Freescale Semiconductor Package and Pin Listings Table 55. MPC8313E TEPBGAII Pinout Listing (continued) Signal LCS[3] LWE[0] LWE[1] LBCTL LALE/M1LALE/M2LALE LGPL0 LGPL1 LGPL2 LGPL3 LGPL4 LGPL5 LCLK0 LCLK1 LA0/GPIO[0] LA1/GPIO[1] LA2/GPIO[2] LA3/GPIO[3] LA4/GPIO[4] LA5/GPIO[5] LA6/GPIO[6] LA7/GPIO[7] LA8/GPIO[13] LA9/GPIO[14] LA10 LA11 LA12 LA13 LA14 LA15 DUART UART_SOUT1/MSRCID0 UART_SIN1/MSRCID1 UART_CTS[1]/GPIO[8]/MSRCID2 UART_RTS[1]/GPIO[9]/MSRCID3 N2 M5 M1 K1 O IO IO IO NVDD NVDD NVDD NVDD Package Pin Number D26 E24 H26 L22 E26 AA23 AA24 AA25 AA26 Y22 E21 H22 G26 AC24 Y24 Y26 W22 W24 W26 V22 V23 V24 V25 V26 U22 AD24 L25 L24 K26 Pin Type O O O O O O O O O IO O O O IO IO IO IO IO IO IO IO IO IO O O O O O O Power Supply LVDD LVDD LVDD LVDD LVDD LVDD LVDD LVDD LVDD LVDD LVDD LVDD LVDD LVDD LVDD LVDD LVDD LVDD LVDD LVDD LVDD LVDD LVDD LVDD LVDD LVDD LVDD LVDD LVDD Notes MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 61 Package and Pin Listings Table 55. MPC8313E TEPBGAII Pinout Listing (continued) Signal UART_SOUT2/MSRCID4 UART_SIN2/MDVAL UART_CTS[2] UART_RTS[2] I2C interface IIC1_SDA/CKSTOP_OUT IIC1_SCL/CKSTOP_IN IIC2_SDA/PMC_PWR_OK/GPIO[10] IIC2_SCL/GPIO[11] Interrupts MCP_OUT IRQ[0]/MCP_IN IRQ[1] IRQ[2] IRQ[3] /CKSTOP_OUT IRQ[4]/ CKSTOP_IN/GPIO[12] Configuration CFG_CLKIN_DIV EXT_PWR_CTRL CFG_LBIU_MUX_EN JTAG TCK TDI TDO TMS TRST TEST TEST_MODE DEBUG QUIESCE System Control HRESET F2 IO NVDD 1 F5 O NVDD F4 I NVDD 6 E1 E2 E3 E4 E5 I I O I I NVDD NVDD NVDD NVDD NVDD 4 3 4 4 D5 J5 R24 I O I NVDD NVDD NVDD G5 K5 K4 K2 K3 J1 O I I I IO IO NVDD NVDD NVDD NVDD NVDD NVDD 2 J4 J2 J3 H5 IO IO IO IO NVDD NVDD NVDD NVDD 2 2 2 2 Package Pin Number M3 L1 L5 L3 Pin Type O IO IO IO Power Supply NVDD NVDD NVDD NVDD Notes MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 62 Freescale Semiconductor Package and Pin Listings Table 55. MPC8313E TEPBGAII Pinout Listing (continued) Signal PORESET SRESET Clocks SYS_CR_CLK_IN SYS_CR_CLK_OUT SYS_CLK_IN USB_CR_CLK_IN USB_CR_CLK_OUT USB_CLK_IN PCI_SYNC_OUT RTC_PIT_CLOCK PCI_SYNC_IN MISC AVDD1 AVDD2 PCI PCI_INTA PCI_RESET_OUT PCI_AD[0] PCI_AD[1] PCI_AD[2] PCI_AD[3] PCI_AD[4] PCI_AD[5] PCI_AD[6] PCI_AD[7] PCI_AD[8] PCI_AD[9] PCI_AD[10] PCI_AD[11] PCI_AD[12] PCI_AD[13] AF7 AB11 AB20 AF23 AF22 AB19 AE22 AF21 AD19 AD20 AC18 AD18 AB18 AE19 AB17 AE18 O O IO IO IO IO IO IO IO IO IO IO IO IO IO IO NVDD NVDD NVDD NVDD NVDD NVDD NVDD NVDD NVDD NVDD NVDD NVDD NVDD NVDD NVDD NVDD F14 P21 I I Double with Pad Double with Pad U26 U25 U23 T26 R26 T22 U24 R22 T24 I O I I O I O I I NVDD NVDD NVDD NVDD NVDD NVDD NVDD NVDD NVDD 3 Package Pin Number F3 F1 Pin Type I I Power Supply NVDD NVDD Notes MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 63 Package and Pin Listings Table 55. MPC8313E TEPBGAII Pinout Listing (continued) Signal PCI_AD[14] PCI_AD[15] PCI_AD[16] PCI_AD[17] PCI_AD[18] PCI_AD[19] PCI_AD[20] PCI_AD[21] PCI_AD[22] PCI_AD[23] PCI_AD[24] PCI_AD[25] PCI_AD[26] PCI_AD[27] PCI_AD[28] PCI_AD[29] PCI_AD[30] PCI_AD[31] PCI_C/BE[0] PCI_C/BE[1] PCI_C/BE[2] PCI_C/BE[3] PCI_PAR PCI_FRAME PCI_TRDY PCI_IRDY PCI_STOP PCI_DEVSEL PCI_IDSEL PCI_SERR PCI_PERR PCI_REQ0 PCI_REQ1/CPCI_HS_ES PCI_REQ2 Package Pin Number AD17 AF19 AB14 AF15 AD14 AE14 AF12 AE11 AD12 AB13 AF9 AD11 AE10 AB12 AD10 AC10 AF10 AF8 AC19 AB15 AF14 AF11 AD16 AF16 AD13 AC15 AF13 AC14 AF20 AE15 AD15 AB10 AD9 AD8 Pin Type IO IO IO IO IO IO IO IO IO IO IO IO IO IO IO IO IO IO IO IO IO IO IO IO IO IO IO IO I IO IO IO I I Power Supply NVDD NVDD NVDD NVDD NVDD NVDD NVDD NVDD NVDD NVDD NVDD NVDD NVDD NVDD NVDD NVDD NVDD NVDD NVDD NVDD NVDD NVDD NVDD NVDD NVDD NVDD NVDD NVDD NVDD NVDD NVDD NVDD NVDD NVDD 5 5 5 5 5 5 5 Notes MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 64 Freescale Semiconductor Package and Pin Listings Table 55. MPC8313E TEPBGAII Pinout Listing (continued) Signal PCI_GNT0 PCI_GNT1/CPCI_HS_LED PCI_GNT2/CPCI_HS_ENUM M66EN PCI_CLK0 PCI_CLK1 PCI_CLK2 PCI_PME Package Pin Number AC11 AE7 AD7 AD21 AF17 AB16 AF18 AD22 ETSEC1/_USBULPI TSEC1_COL/USBDR_TXDRXD0 TSEC1_CRS/USBDR_TXDRXD1 TSEC1_GTX_CLK/USBDR_TXDRXD2 TSEC1_RX_CLK/USBDR_TXDRXD3 TSCE1_RX_DV/USBDR_TXDRXD4 TSEC1_RXD[3]/USBDR_TXDRXD5 TSEC1_RXD[2]/USBDR_TXDRXD6 TSEC1_RXD[1]/USBDR_TXDRXD7 TSEC1_RXD[0]/USBDR_NXT/TSEC_1588_TRIG1 TSEC1_RX_ER/USBDR_DIR/TESC_1588_TRIG2 TSEC1_TX_CLK/USBDR_CLK/TSEC_1588_CLK TSEC1_TXD[3]/TSEC_1588_GCLK TSEC1_TXD[2]/TSEC_1588_PP1 TSEC1_TXD[1]/TSEC_1588_PP2 TSEC1_TXD[0]/USBDR_STP/TSEC_1588_PP3 TSEC1_TX_EN/TSEC_1588_ALARM1 TSEC1_TX_ER/TSEC_1588_ALARM2 TSEC1_GTX_CLK125 TSEC1_MDC TSEC1_MDIO ETSEC2 TSEC2_COL/GTM1_TIN4/GTM2_TIN3/GPIO[15] TSEC2_CRS/GTM1_TGATE4/GTM2_TGATE3/GPIO[16] TSEC2_GTX_CLK/GTM1_TOUT4/GTM2_TOUT3/GPIO[17] TSEC2_RX_CLK/GTM1_TIN2/GTM2_TIN1/GPIO[18] AB4 AB3 AC1 AC2 IO IO IO IO LVDDA LVDDA LVDDA LVDDA AD2 AC3 AF3 AE3 AD3 AC6 AF4 AB6 AB5 AD4 AF5 AE6 AC7 AD6 AD5 AB7 AB8 AE1 AF6 AB9 IO IO IO IO IO IO IO IO I I I O O O O O O I O IO LVDDB LVDDB LVDDB LVDDB LVDDB LVDDB LVDDB LVDDB LVDDB LVDDB LVDDB LVDDB LVDDB LVDDB LVDDB LVDDB LVDDB LVDDB NVDD NVDD 2 3 Pin Type IO O O I O O O IO Power Supply NVDD NVDD NVDD NVDD NVDD NVDD NVDD NVDD Notes MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 65 Package and Pin Listings Table 55. MPC8313E TEPBGAII Pinout Listing (continued) Signal TSCE2_RX_DV/GTM1_TGATE2/GTM2_TGATE1/GPIO[19] TSEC2_RXD[3]/GPIO[20] TSEC2_RXD[2]/GPIO[21] TSEC2_RXD[1]/GPIO[22] TSEC2_RXD[0]/GPIO[23] TSEC2_RX_ER/GTM1_TOUT 2/GTM2_TOUT1/GPIO[24] TSEC2_TX_CLK/GPIO[25] TSEC2_TXD[3]/CFG_RESET_SOURCE[0] TSEC2_TXD[2]/CFG_RESET_SOURCE[1] TSEC2_TXD[1]/CFG_RESET_SOURCE[2] TSEC2_TXD[0]/CFG_RESET_SOURCE[3] TSEC2_TX_EN/GPIO[26] TSEC2_TX_ER/GPIO[27] SGMII PHY TXA TXA RXA RXA TXB TXB RXB RXB SD_IMP_CAL_RX SD_REF_CLK SD_REF_CLK SD_PLL_TPD SD_IMP_CAL_TX SDAVDD SD_PLL_TPA_ANA SDAVSS USB PHY USB_DP USB_DM USB_VBUS P26 N26 P24 IO IO IO U3 V3 U1 V1 P4 N4 R1 P1 V5 T5 T4 T2 N5 R5 R4 R3 O O I I O O I I I I I O I IO O IO Package Pin Number AA3 Y5 AA4 AB2 AA5 AA2 AB1 W3 Y1 W5 Y3 AA1 W1 Pin Type IO IO IO IO IO IO IO IO IO IO IO IO IO Power Supply LVDDA LVDDA LVDDA LVDDA LVDDA LVDDA LVDDA LVDDA LVDDA LVDDA LVDDA LVDDA LVDDA Notes MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 66 Freescale Semiconductor Package and Pin Listings Table 55. MPC8313E TEPBGAII Pinout Listing (continued) Signal USB_TPA USB_RBIAS USB_PLL_PWR3 USB_PLL_GND USB_PLL_PWR1 USB_VSSA_BIAS USB_VDDA_BIAS USB_VSSA USB_VDDA GTM/USB USBDR_DRIVE_VBUS/GTM1_TIN1/GTM2_TIN2 USBDR_PWRFAULT/GTM1_TGATE1/GTM2_TGATE2 USBDR_PCTL0/GTM1_TOUT1 USBDR_PCTL1 SPI SPIMOSI/GTM1_TIN3/GTM2_TIN4/GPIO[28] SPIMISO/GTM1_TGATE3/GTM2_TGATE 4/GPIO[29]/LDVAL SPICLK/GTM1_TOUT3/GPIO[30] SPISEL/GPIO[31] H1 H3 G1 G3 Power and Ground Supplies GV DD A2,A3,A4,A24,A25,B3, B4,B5,B12,B13,B20, B21,B24,B25,B26,D1, D2,D8,D9,D16,D17 D24,D25,G23,H23,R23, T23,W25,Y25, AA22,AC23 W2,Y2 AC8,AC9,AE4,AE5 C14,D14 G4,H4,L2,M2,AC16, AC17,AD25,AD26,AE12, AE13,AE20,AE21,AE24, AE25,AE26,AF24, AF25 IO IO IO IO NVDD NVDD NVDD NVDD AD23 AE23 AC22 AB21 IO IO O O NVDD NVDD NVDD NVDD Package Pin Number L26 M24 M26 N24 N25 M25 M22 N22 P22 Pin Type IO IO IO IO IO IO IO IO IO Power Supply Notes LVDD LVDDA LVDDB MV REF NVDD MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 67 Package and Pin Listings Table 55. MPC8313E TEPBGAII Pinout Listing (continued) Signal VDD Package Pin Number K11,K12,K13,K14,K15,K 16,L10,L17,M10,M17, N10,N17,U12,U13, T1,U2,V2,P5,U4 F6,F10,F19,K6,K10,K17, K21,P6,P10,P17,R10, R17,T10,T17,U10,U11, U14,U15,U16,U17,W6, W21,AA6,AA10,AA14, AA19 B1,B2,B8,B9,B16,B17, C1,C2,C3,C4,C5,C24, C25,C26,D3,D4,D12, D13,D20,D21,F8,F11, F13,F16,F17,F21,G2, G25,H2,H6,H21,H25, L4,L6,L11,L12,L13,L14, L15,L16,L21,L23,M4, M11,M12,M13,M14, M15,M16,M23,N1, N3,N6,N11,N12,N13, N14,N15,N16,N21,N23, P11,P12,P13,P14,P15, P16,P23,P25,R11,R12, R13,R14,R15,R16,R25, T6,T11,T12,T13,T14, T15,T16,T21,T25,U5, U6,U21,W4,W23,Y4, Y23,AA8,AA11,AA13, AA16,AA17,AA21,AC4, AC5,AC12,AC13,AC20, AC21,AD1,AE2,AE8, AE9,AE16,AE17,AF2, P2, R2,T3,P3,V4 Pin Type Power Supply Notes VDDC VSS Notes: 1. This pin is an open drain signal. A weak pull-up resistor (1 kΩ) should be placed on this pin to NVDD 2. This pin is an open drain signal. A weak pull-up resistor (2–10 kΩ) should be placed on this pin to NVDD. 3. This output is actively driven during reset rather than being three-stated during reset. 4. These JTAG pins have weak internal pull-up P-FETs that are always enabled. 5. This pin should have a weak pull up if the chip is in PCI host mode. Follow PCI specifications recommendation. 6. This pin must always be tied to VSS. MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 68 Freescale Semiconductor Clocking 19 Clocking Figure 39 shows the internal distribution of clocks within the MPC8313E. MPC8313E e300c3 core Core PLL USB Mac USB PHY PLL to DDR memory controller DDR Clock Divider /2 MEMC_MCK MEMC_MCK DDR Memory Device xM 1 core_clk mux csb_clk USB_CLK_IN USB_CR_CLK_IN Crystal USB_CR_CLK_OUT x L2 Clock Unit ddr_clk /1,/2 System PLL lbc_clk /n To local bus LBC Clock Divider LCLK[0:1] Local Bus Memory Device CFG_CLKIN _DIV SYS_CLK_IN SYS_CR_CLK_IN Crystal SYS_CR_CLK_OUT csb_clk to rest of the device PCI_CLK/ PCI_SYNC_IN 1 0 PCI Clock Divider (÷2) 3 PCI_SYNC_OUT PCI_CLK_OUT[0:2] GTX_CLK125 125-MHz source eTSEC Protocol Converter Sys Ref RTC RTC_CLK (32 KHz) 1 2 Multiplication factor M = 1, 1.5, 2, 2.5, and 3. Multiplication factor L = 2, 3, 4, 5 and 6. Value is decided by RCWLR[SPMF]. Figure 39. MPC8313E Clock Subsystem MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 69 Clocking The primary clock source for the MPC8313E can be one of two inputs, SYS_CLK_IN or PCI_CLK, depending on whether the device is configured in PCI host or PCI agent mode. When the device is configured as a PCI host device, SYS_CLK_IN is its primary input clock. SYS_CLK_IN feeds the PCI clock divider (÷2) and the multiplexors for PCI_SYNC_OUT and PCI_CLK_OUT. The CFG_CLKIN_DIV configuration input selects whether SYS_CLK_IN or SYS_CLK_IN/2 is driven out on the PCI_SYNC_OUT signal. The OCCR[PCICOEn] parameters select whether the PCI_SYNC_OUT is driven out on the PCI_CLK_OUTn signals. PCI_SYNC_OUT is connected externally to PCI_SYNC_IN to allow the internal clock subsystem to synchronize to the system PCI clocks. PCI_SYNC_OUT must be connected properly to PCI_SYNC_IN, with equal delay to all PCI agent devices in the system, to allow the device to function. When the device is configured as a PCI agent device, PCI_SYNC_IN is the primary input clock. When the device is configured as a PCI agent device the SYS_CLK_IN signal should be tied to VSS. As shown in Figure 39, the primary clock input (frequency) is multiplied up by the system phase-locked loop (PLL) and the clock unit to create the coherent system bus clock (csb_clk), the internal clock for the DDR controller (ddr_clk), and the internal clock for the local bus interface unit (lbc_clk). The csb_clk frequency is derived from a complex set of factors that can be simplified into the following equation: csb_clk = {PCI_SYNC_IN × (1 + ~CFG_CLKIN_DIV)} × SPMF In PCI host mode, PCI_SYNC_IN × (1 + ~CFG_CLKIN_DIV) is the SYS_CLK_IN frequency. The csb_clk serves as the clock input to the e300 core. A second PLL inside the e300 core multiplies up the csb_clk frequency to create the internal clock for the e300 core (core_clk). The system and core PLL multipliers are selected by the SPMF and COREPLL fields in the reset configuration word low (RCWL) which is loaded at power-on reset or by one of the hard-coded reset options. See Chapter 4, “Reset, Clocking, and Initialization,” in the MPC8313E PowerQUICC II Pro Integrated Host Processor Reference Manual for more information on the clock subsystem. The internal ddr_clk frequency is determined by the following equation: ddr_clk = csb_clk × (1 + RCWL[DDRCM]) Note that ddr_clk is not the external memory bus frequency; ddr_clk passes through the DDR clock divider (÷2) to create the differential DDR memory bus clock outputs (MCK and MCK). However, the data rate is the same frequency as ddr_clk. The internal lbc_clk frequency is determined by the following equation: lbc_clk = csb_clk × (1 + RCWL[LBCM]) Note that lbc_clk is not the external local bus frequency; lbc_clk passes through the a LBC clock divider to create the external local bus clock outputs (LCLK[0:1]). The LBC clock divider ratio is controlled by LCCR[CLKDIV]. In addition, some of the internal units may be required to be shut off or operate at lower frequency than the csb_clk frequency. Those units have a default clock ratio that can be configured by a memory mapped register after the device comes out of reset. Table 56 specifies which units have a configurable clock frequency. MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 70 Freescale Semiconductor Clocking Table 56. Configurable Clock Units Unit TSEC1 TSEC2 Security Core, I2C, SAP, TPR USB DR PCI and DMA complex Default Frequency Options Off, csb_clk, csb_clk/2, csb_clk/3 Off, csb_clk, csb_clk/2, csb_clk/3 Off, csb_clk, csb_clk/2, csb_clk/3 Off, csb_clk, csb_clk/2, csb_clk/3 Off, csb_clk csb_clk csb_clk csb_clk csb_clk csb_clk Table 57 provides the operating frequencies for the MPC8313E TEPBGA II under recommended operating conditions (see Table 2). Table 57. Operating Frequencies for TEPBGA I I Characteristic1 e300 core frequency (core_clk) Coherent system bus frequency (csb_clk) DDR1/2 memory bus frequency (MCK)2 Local bus frequency (LCLKn)3 PCI input frequency (SYS_CLK_IN or PCI_CLK) Max Operating Frequency 333 167 Unit MHz MHz 167 MHz 33–66 MHz 24–66 MHz Notes: 1. The SYS_CLK_IN frequency, RCWL[SPMF], and RCWL[COREPLL] settings must be chosen such that the resulting csb_clk, MCK, LCLK[0:1], and core_clk frequencies do not exceed their respective maximum or minimum operating frequencies. The value of SCCR[ENCCM] and SCCR[USBDRCM] must be programmed such that the maximum internal operating frequency of the Security core and USB modules will not exceed their respective value listed in this table. 2. The DDR data rate is 2x the DDR memory bus frequency. 3. The local bus frequency is 1/2, 1/4, or 1/8 of the lbc_clk frequency (depending on LCCR[CLKDIV]) which is in turn 1x or 2x the csb_clk frequency (depending on RCWL[LBCM]). MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 71 Clocking 19.1 System PLL Configuration The system PLL is controlled by the RCWL[SPMF] parameter. Table 58 shows the multiplication factor encodings for the system PLL. Table 58. System PLL Multiplication Factors RCWL[SPMF] 0000 0001 0010 0011 0100 0101 0110 0111–1111 System PLL Multiplication Factor Reserved Reserved ×2 ×3 ×4 ×5 ×6 Reserved As described in Section 19, “Clocking,” The LBCM, DDRCM, and SPMF parameters in the reset configuration word low and the CFG_CLKIN_DIV configuration input signal select the ratio between the primary clock input (SYS_CLK_IN or PCI_SYNC_IN) and the internal coherent system bus clock (csb_clk). Table 59 shows the expected frequency values for the CSB frequency for select csb_clk to SYS_CLK_IN/PCI_SYNC_IN ratios. Table 59. CSB Frequency Options Input Clock Frequency(MHz)2 24 25 csb_clk High High High High High Low Low Low 0010 0011 0100 0101 0110 0010 0011 0100 2:1 3:1 4:1 5:1 6:1 2:1 3:1 4:1 100 100 133 120 144 100 125 150 133 100 133 167 33.33 Frequency(MHz) 133 66.67 CFG_CLKIN_DIV at reset 1 SPMF csb_clk : Input Clock Ratio 2 MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 72 Freescale Semiconductor Clocking Table 59. CSB Frequency Options (continued) Input Clock Frequency(MHz)2 24 25 csb_clk Low Low 1 2 CFG_CLKIN_DIV at reset 1 SPMF csb_clk : Input Clock Ratio 2 33.33 Frequency(MHz) 167 66.67 0101 0110 5:1 6:1 120 144 125 150 CFG_CLKIN_DIV select the ratio between SYS_CLK_IN and PCI_SYNC_OUT. SYS_CLK_IN is the input clock in host mode; PCI_CLK is the input clock in agent mode. 19.2 Core PLL Configuration RCWL[COREPLL] selects the ratio between the internal coherent system bus clock (csb_clk) and the e300 core clock (core_clk). Table 60 shows the encodings for RCWL[COREPLL]. COREPLL values that are not listed in Table 60 should be considered as reserved. NOTE Core VCO frequency = Core frequency × VCO divider VCO divider has to be set properly so that the core VCO frequency is in the range of 400–800 MHz. Table 60. e300 Core PLL Configuration RCWL[COREPLL] VCO divider 1 core_clk : csb_clk Ratio 0–1 2–5 0000 6 0 n 0 0 0 1 1 1 0 0 0 1 1 PLL bypassed (PLL off, csb_clk clocks core directly) n/a 1:1 1:1 1:1 1.5:1 1.5:1 1.5:1 2:1 2:1 2:1 2.5:1 2.5:1 nn 11 00 01 10 00 01 10 00 01 10 00 01 PLL bypassed (PLL off, csb_clk clocks core directly) n/a 2 4 8 2 4 8 2 4 8 2 4 nnnn 0001 0001 0001 0001 0001 0001 0010 0010 0010 0010 0010 MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 73 Clocking Table 60. e300 Core PLL Configuration (continued) RCWL[COREPLL] VCO divider 1 core_clk : csb_clk Ratio 0–1 10 00 01 10 1 2–5 0010 0011 0011 0011 6 1 0 0 0 2.5:1 3:1 3:1 3:1 8 2 4 8 Core VCO frequency = Core frequency × VCO divider. Note that VCO divider has to be set properly so that the core VCO frequency is in the range of 400-800MHz. 19.3 Example Clock Frequency Combinations Table 61 shows several possible frequency combinations that can be selected based on the indicated input reference frequencies, with RCWLR[LBCM] = 0 and RCWLR[DDRCM] =1, such that the LBC operates with a frequency equal to the frequency of csb_clk and the DDR controller operates at twice the frequency of csb_clk. Table 61. System Clock Frequencies LBC(lbc_clk) SYS_CLK_ SPMF vcod IN/ 1 2 PCI_CLK 24.0 24.0 6 5 2 2 CSB(csb_ clk) 144.0 120.0 DDR (ddr_clk) 288.0 240.0 60 USB ref 3 12.0 12.0 e300 Core(core_clk) vco /2 /4 /8 ×1 144.0 120.0 × 1.5 216 180 ×2 288 240 × 2.5 360 300 ×3 576.0 480.0 36 30 18.0 15.0 360 25.0 25.0 6 5 2 2 600.0 500.0 150.0 125.0 300.0 250.0 37.5 18.8 Note 1 Note1 150.0 125.0 225 188 300 250 375 313 375 62.5 31.25 15.6 32.0 32.0 5 4 2 2 640.0 512.0 160.0 128.0 320.0 256.0 64 40 32 20.0 16.0 16.0 16.0 160.0 128.0 240 192 320 256 320 384 33.3 33.3 5 4 2 2 666.0 532.8 166.5 133.2 333.0 266.4 66.6 41.63 20.8 33.3 16.7 Note 1 Note 1 166.5 133.2 250 200 333 266 333 400 48.0 3 2 576.0 144.0 288.0 36 18.0 48.0 144.0 216 288 360 MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 74 Freescale Semiconductor Clocking Table 61. System Clock Frequencies (continued) 66.7 2 2 533.4 133.3 266.7 66.7 33.34 16.7 Note 1 133.3 200 267 333 400 Note: Note 1: USB reference clock must be supplied from a separate source as it must be 12, 16 or 48 MHz, the USB reference must be supplied from a separate external source using USB_CLK_IN. Note 2: When considering operating frequencies, the valid system APLL VCO operating range of 400-800 MHz must not be violated. Note 3: csb_clk frequencies of less than 133MHz will not support Gigabit Ethernet data rates. 1 2 System PLL Multiplication Factor System PLL VCO Divider 3 Frequency of USB PLL Input reference MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 75 Thermal 20 Thermal This section describes the thermal specifications of the MPC8313E. 20.1 Thermal Characteristics Table 62. Package Thermal Characteristics for TEPBGAII Characteristic Junction to Ambient Natural Convection Junction to Ambient Natural Convection Junction to Ambient (@200 ft/min) Junction to Ambient (@200 ft/min) Junction to Board Junction to Case Junction to Package Top Natural Convection Board type Single layer board (1s) Four layer board (2s2p) Single layer board (1s) Four layer board (2s2p) Symbol TEPBGAII 25 18 20 15 10 8 7 Unit °C/W °C/W °C/W °C/W °C/W °C/W °C/W Notes 1,2 1,2,3 1,3 1,3 4 5 6 Table 62 provides the package thermal characteristics for the 516 27 × 27 mm TEPBGAII. RθJA RθJA RθJMA RθJMA RθJB RθJC ΨJT Notes: 1. Junction temperature is a function of die size, on-chip power dissipation, package thermal resistance, mounting site (board) temperature, ambient temperature, air flow, power dissipation of other components on the board, and board thermal resistance. 2. Per JEDEC JESD51-2 with the single layer board horizontal. Board meets JESD51-9 specification. 3. Per JEDEC JESD51-6 with the board horizontal. 4. Thermal resistance between the die and the printed circuit board per JEDEC JESD51-8. Board temperature is measured on the top surface of the board near the package. 5. Thermal resistance between the die and the case top surface as measured by the cold plate method (MIL SPEC-883 Method 1012.1). 6. Thermal characterization parameter indicating the temperature difference between package top and the junction temperature per JEDEC JESD51-2. When Greek letters are not available, the thermal characterization parameter is written as Psi-JT. MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 76 Freescale Semiconductor Thermal 20.2 Thermal Management Information For the following sections, PD = (VDD x IDD) + PI/O where PI/O is the power dissipation of the I/O drivers. 20.2.1 Estimation of Junction Temperature with Junction-to-Ambient Thermal Resistance TJ = TA + (RθJA × PD) where: TJ = junction temperature (°C) TA = ambient temperature for the package (°C) RθJA = junction to ambient thermal resistance (°C/W) PD = power dissipation in the package (W) An estimation of the chip junction temperature, TJ, can be obtained from the equation: The junction to ambient thermal resistance is an industry standard value that provides a quick and easy estimation of thermal performance. As a general statement, the value obtained on a single layer board is appropriate for a tightly packed printed circuit board. The value obtained on the board with the internal planes is usually appropriate if the board has low power dissipation and the components are well separated. Test cases have demonstrated that errors of a factor of two (in the quantity TJ – TA) are possible. 20.2.2 Estimation of Junction Temperature with Junction-to-Board Thermal Resistance The thermal performance of a device cannot be adequately predicted from the junction to ambient thermal resistance. The thermal performance of any component is strongly dependent on the power dissipation of surrounding components. In addition, the ambient temperature varies widely within the application. For many natural convection and especially closed box applications, the board temperature at the perimeter (edge) of the package will be approximately the same as the local air temperature near the device. Specifying the local ambient conditions explicitly as the board temperature provides a more precise description of the local ambient conditions that determine the temperature of the device. At a known board temperature, the junction temperature is estimated using the following equation: TJ = TB + (RθJB × PD) where: TJ = junction temperature (°C) TB = board temperature at the package perimeter (°C) RθJB = junction to board thermal resistance (°C/W) per JESD51–8 PD = power dissipation in the package (W) When the heat loss from the package case to the air can be ignored, acceptable predictions of junction temperature can be made. The application board should be similar to the thermal test condition: the component is soldered to a board with internal planes. MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 77 Thermal 20.2.3 Experimental Determination of Junction Temperature To determine the junction temperature of the device in the application after prototypes are available, the Thermal Characterization Parameter (ΨJT) can be used to determine the junction temperature with a measurement of the temperature at the top center of the package case using the following equation: TJ = TT + (ΨJT × PD) where: TJ = junction temperature (°C) TT = thermocouple temperature on top of package (°C) ΨJT = thermal characterization parameter (°C/W) PD = power dissipation in the package (W) The thermal characterization parameter is measured per JESD51-2 specification using a 40 gauge type T thermocouple epoxied to the top center of the package case. The thermocouple should be positioned so that the thermocouple junction rests on the package. A small amount of epoxy is placed over the thermocouple junction and over about 1 mm of wire extending from the junction. The thermocouple wire is placed flat against the package case to avoid measurement errors caused by cooling effects of the thermocouple wire. 20.2.4 Heat Sinks and Junction-to-Case Thermal Resistance In some application environments, a heat sink will be required to provide the necessary thermal management of the device. When a heat sink is used, the thermal resistance is expressed as the sum of a junction to case thermal resistance and a case to ambient thermal resistance: RθJA = RθJC + RθCA where: RθJA = junction to ambient thermal resistance (°C/W) RθJC = junction to case thermal resistance (°C/W) RθCA = case to ambient thermal resistance (°C/W) RθJC is device related and cannot be influenced by the user. The user controls the thermal environment to change the case to ambient thermal resistance, RθCA. For instance, the user can change the size of the heat sink, the air flow around the device, the interface material, the mounting arrangement on printed circuit board, or change the thermal dissipation on the printed circuit board surrounding the device. To illustrate the thermal performance of the devices with heat sinks, the thermal performance has been simulated with a few commercially available heat sinks. The heat sink choice is determined by the application environment (temperature, air flow, adjacent component power dissipation) and the physical space available. Because there is not a standard application environment, a standard heat sink is not required. MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 78 Freescale Semiconductor Thermal Table 63. Heat Sinks and Junction-to-Case Thermal Resistance of MPC8313E (TEPBGAII) 35x35 mm TBGA Heat Sink Assuming Thermal Grease Air Flow Junction-to-Ambient Thermal Resistance 10.7 6.2 5.3 8.1 4.4 3.7 5.4 3.2 2.4 6.4 3.8 2.5 2.8 AAVID 30x30x9.4 mm Pin Fin AAVID 30x30x9.4 mm Pin Fin AAVID 30x30x9.4 mm Pin Fin AAVID 31x35x23 mm Pin Fin AAVID 31x35x23 mm Pin Fin AAVID 31x35x23 mm Pin Fin Wakefield, 53x53x25 mm Pin Fin Wakefield, 53x53x25 mm Pin Fin Wakefield, 53x53x25 mm Pin Fin MEI, 75x85x12 no adjacent board, extrusion MEI, 75x85x12 no adjacent board, extrusion MEI, 75x85x12 no adjacent board, extrusion MEI, 75x85x12 mm, adjacent board, 40 mm Side bypass Natural Convection 1 m/s 2 m/s Natural Convection 1 m/s 2 m/s Natural Convection 1 m/s 2 m/s Natural Convection 1 m/s 2 m/s 1 m/s Accurate thermal design requires thermal modeling of the application environment using computational fluid dynamics software which can model both the conduction cooling and the convection cooling of the air moving through the application. Simplified thermal models of the packages can be assembled using the junction-to-case and junction-to-board thermal resistances listed in the thermal resistance table. More detailed thermal models can be made available on request. Heat sink Vendors include the following list: Aavid Thermalloy 80 Commercial St. Concord, NH 03301 Internet: www.aavidthermalloy.com Alpha Novatech 473 Sapena Ct. #12 Santa Clara, CA 95054 Internet: www.alphanovatech.com International Electronic Research Corporation (IERC) 413 North Moss St. Burbank, CA 91502 Internet: www.ctscorp.com 603-224-9988 408-749-7601 818-842-7277 MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 79 Thermal Millennium Electronics (MEI) Loroco Sites 671 East Brokaw Road San Jose, CA 95112 Internet: www.mei-thermal.com Tyco Electronics Chip Coolers™ P.O. Box 3668 Harrisburg, PA 17105 Internet: www.chipcoolers.com Wakefield Engineering 33 Bridge St. Pelham, NH 03076 Internet: www.wakefield.com 408-436-8770 800-522-6752 603-635-2800 Interface material vendors include the following: Chomerics, Inc. 77 Dragon Ct. Woburn, MA 01801 Internet: www.chomerics.com Dow-Corning Corporation Corporate Center PO BOX 994 Midland, MI 48686-0994 Internet: www.dowcorning.com Shin-Etsu MicroSi, Inc. 10028 S. 51st St. Phoenix, AZ 85044 Internet: www.microsi.com The Bergquist Company 18930 West 78th St. Chanhassen, MN 55317 Internet: www.bergquistcompany.com 781-935-4850 800-248-2481 888-642-7674 800-347-4572 20.3 Heat Sink Attachment When attaching heat sinks to these devices, an interface material is required. The best method is to use thermal grease and a spring clip. The spring clip should connect to the printed circuit board, either to the board itself, to hooks soldered to the board, or to a plastic stiffener. Avoid attachment forces which would lift the edge of the package or peel the package from the board. Such peeling forces reduce the solder joint lifetime of the package. Recommended maximum force on the top of the package is 10 lb (4.5 kg) force. If an adhesive attachment is planned, the adhesive should be intended for attachment to painted or plastic surfaces and its performance verified under the application requirements. MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 80 Freescale Semiconductor System Design Information 20.3.1 Experimental Determination of the Junction Temperature with a Heat Sink When heat sink is used, the junction temperature is determined from a thermocouple inserted at the interface between the case of the package and the interface material. A clearance slot or hole is normally required in the heat sink. Minimizing the size of the clearance is important to minimize the change in thermal performance caused by removing part of the thermal interface to the heat sink. Because of the experimental difficulties with this technique, many engineers measure the heat sink temperature and then back calculate the case temperature using a separate measurement of the thermal resistance of the interface. From this case temperature, the junction temperature is determined from the junction to case thermal resistance. TJ = TC + (RθJC x PD) Where: TJ = junction temperature (°C) TC = case temperature of the package RθJC = junction-to-case thermal resistance PD = power dissipation 21 System Design Information This section provides electrical and thermal design recommendations for successful application of the MPC8313E SYS_CLK_IN 21.1 System Clocking The MPC8313E includes two PLLs. 1. The platform PLL (AVDD2) generates the platform clock from the externally supplied SYS_CLK_IN input in PCI host mode or SYS_CLK_IN/PCI_SYNC_IN in PCI agent mode. The frequency ratio between the platform and SYS_CLK_IN is selected using the platform PLL ratio configuration bits as described in Section 19.1, “System PLL Configuration.” 2. The e300 Core PLL (AVDD1) generates the core clock as a slave to the platform clock. The frequency ratio between the e300 core clock and the platform clock is selected using the e300 PLL ratio configuration bits as described in Section 19.2, “Core PLL Configuration.” 21.2 PLL Power Supply Filtering Each of the PLLs listed above is provided with power through independent power supply pins (AVDD1, AVDD2 respectively). The AVDD level should always be equivalent to VDD, and preferably these voltages will be derived directly from VDD through a low frequency filter scheme such as the following. There are a number of ways to reliably provide power to the PLLs, but the recommended solution is to provide five independent filter circuits as illustrated in Figure 40, one to each of the five AVDD pins. By providing independent filters to each PLL the opportunity to cause noise injection from one PLL to the other is reduced. MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 81 System Design Information This circuit is intended to filter noise in the PLLs resonant frequency range from a 500 kHz to 10 MHz range. It should be built with surface mount capacitors with minimum Effective Series Inductance (ESL). Consistent with the recommendations of Dr. Howard Johnson in High Speed Digital Design: A Handbook of Black Magic (Prentice Hall, 1993), multiple small capacitors of equal value are recommended over a single large value capacitor. Each circuit should be placed as close as possible to the specific AVDD pin being supplied to minimize noise coupled from nearby circuits. It should be possible to route directly from the capacitors to the AV DD pin, which is on the periphery of package, without the inductance of vias. Figure 40 shows the PLL power supply filter circuit. 10 Ω V DD 2.2 µF 2.2 µF Low ESL Surface Mount Capacitors AVDD (or L2AV DD) VSS Figure 40. PLL Power Supply Filter Circuit 21.3 Decoupling Recommendations Due to large address and data buses, and high operating frequencies, the device can generate transient power surges and high frequency noise in its power supply, especially while driving large capacitive loads. This noise must be prevented from reaching other components in the MPC8313E system, and the MPC8313E itself requires a clean, tightly regulated source of power. Therefore, it is recommended that the system designer place at least one decoupling capacitor at each VDD, NVDD, GVDD, LVDD, LVDDA, and LVDDB pins of the device. These decoupling capacitors should receive their power from separate VDD, NVDD, GVDD, LVDD, LVDDA, LVDDB and VSS power planes in the PCB, utilizing short traces to minimize inductance. Capacitors may be placed directly under the device using a standard escape pattern. Others may surround the part. These capacitors should have a value of 0.01 or 0.1 µF. Only ceramic SMT (surface mount technology) capacitors should be used to minimize lead inductance, preferably 0402 or 0603 sizes. In addition, it is recommended that there be several bulk storage capacitors distributed around the PCB, feeding the VDD, NVDD, GVDD, LVDD, LVDDA, and LVDDB planes, to enable quick recharging of the smaller chip capacitors. These bulk capacitors should have a low ESR (equivalent series resistance) rating to ensure the quick response time necessary. They should also be connected to the power and ground planes through two vias to minimize inductance. Suggested bulk capacitors—100–330 µF (AVX TPS tantalum or Sanyo OSCON). 21.4 Connection Recommendations To ensure reliable operation, it is highly recommended to connect unused inputs to an appropriate signal level. Unused active low inputs should be tied to NVDD, GVDD, LVDD, LVDDA or LVDDB as required. Unused active high inputs should be connected to VSS. All NC (no-connect) signals must remain unconnected. MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 82 Freescale Semiconductor System Design Information Power and ground connections must be made to all external VDD, NVDD, GVDD, LVDD, LVDDA, LVDDB, and VSS pins of the device. 21.5 Output Buffer DC Impedance The MPC8313E drivers are characterized over process, voltage, and temperature. For all buses, the driver is a push-pull single-ended driver type (open drain for I2C). To measure Z0 for the single-ended drivers, an external resistor is connected from the chip pad to NVDD or VSS. Then, the value of each resistor is varied until the pad voltage is NVDD/2 (see Figure 41). The output impedance is the average of two components, the resistances of the pull-up and pull-down devices. When data is held high, SW1 is closed (SW2 is open) and RP is trimmed until the voltage at the pad equals NVDD/2. RP then becomes the resistance of the pull-up devices. RP and RN are designed to be close to each other in value. Then, Z0 = (RP + RN)/2. NVDD RN SW2 Data Pad SW1 RP VSS Figure 41. Driver Impedance Measurement The value of this resistance and the strength of the driver’s current source can be found by making two measurements. First, the output voltage is measured while driving logic 1 without an external differential termination resistor. The measured voltage is V1 = Rsource × Isource. Second, the output voltage is measured while driving logic 1 with an external precision differential termination resistor of value R term. The measured voltage is V2 = (1/(1/R1 + 1/R2)) × Isource. Solving for the output impedance gives Rsource = Rterm × (V1/V2 – 1). The drive current is then Isource = V1/Rsource. MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 83 System Design Information Table 64 summarizes the signal impedance targets. The driver impedance are targeted at minimum VDD, nominal NVDD, 105°C. Table 64. Impedance Characteristics Local Bus, Ethernet, DUART, Control, Configuration, Power Management 42 Target 42 Target NA PCI Signals (not including PCI output clocks) 25 Target 25 Target NA PCI Output Clocks (including PCI_SYNC_OUT) 42 Target 42 Target NA Impedance DDR DRAM Symbol Unit RN RP Differential 20 Target 20 Target NA Z0 Z0 ZDIFF Ω Ω Ω Note: Nominal supply voltages. See Table 1, Tj = 105° C. 21.6 Configuration Pin Muxing The MPC8313E provides the user with power-on configuration options which can be set through the use of external pull-up or pull-down resistors of 4.7 kΩ on certain output pins (see customer visible configuration pins). These pins are generally used as output only pins in normal operation. While HRESET is asserted however, these pins are treated as inputs. The value presented on these pins while HRESET is asserted, is latched when PORESET deasserts, at which time the input receiver is disabled and the I/O circuit takes on its normal function. Careful board layout with stubless connections to these pull-up/pull-down resistors coupled with the large value of the pull-up/pull-down resistor should minimize the disruption of signal quality or speed for output pins thus configured. 21.7 Pull-Up Resistor Requirements The MPC8313E requires high resistance pull-up resistors (10 kΩ is recommended) on open drain type pins including I2C pins, Ethernet Management MDIO pin and EPIC interrupt pins. Correct operation of the JTAG interface requires configuration of a group of system control pins as demonstrated in Figure 42. Care must be taken to ensure that these pins are maintained at a valid deasserted state under normal operating conditions as most have asynchronous behavior and spurious assertion will give unpredictable results. Refer to the PCI 2.2 specification for all pull-ups required for PCI. 21.8 JTAG Configuration Signals Boundary scan testing is enabled through the JTAG interface signals. The TRST signal is optional in IEEE Std. 1149.1, but is provided on all processors that implement the PowerPC architecture. The device requires TRST to be asserted during reset conditions to ensure the JTAG boundary logic does not interfere with normal chip operation. While it is possible to force the TAP controller to the reset state using only the TCK and TMS signals, generally systems will assert TRST during power-on reset. Because the JTAG interface is also used for accessing the common on-chip processor (COP) function, simply tying TRST to PORESET is not practical. MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 84 Freescale Semiconductor System Design Information The COP function of these processors allows a remote computer system (typically, a PC with dedicated hardware and debugging software) to access and control the internal operations of the processor. The COP interface connects primarily through the JTAG port of the processor, with some additional status monitoring signals. The COP port requires the ability to independently assert TRST without causing PORESET. If the target system has independent reset sources, such as voltage monitors, watchdog timers, power supply failures, or push-button switches, then the COP reset signals must be merged into these signals with logic. The arrangement shown in Figure 42 allows the COP to independently assert HRESET or TRST, while ensuring that the target can drive HRESET as well. If the JTAG interface and COP header will not be used, TRST should be tied to PORESET so that it is asserted when the system reset signal (PORESET) is asserted. The COP header shown in Figure 42 adds many benefits—breakpoints, watchpoints, register and memory examination/modification, and other standard debugger features are possible through this interface—and can be as inexpensive as an unpopulated footprint for a header to be added when needed. The COP interface has a standard header for connection to the target system, based on the 0.025" square-post, 0.100" centered header assembly (often called a Berg header). There is no standardized way to number the COP header shown in Figure 42; consequently, many different pin numbers have been observed from emulator vendors. Some are numbered top-to-bottom then left-to-right, while others use left-to-right then top-to-bottom, while still others number the pins counter clockwise from pin 1 (as with an IC). Regardless of the numbering, the signal placement recommended in Figure 42 is common to all known emulators. MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 85 System Design Information PORESET From Target Board Sources (if any) SRESET HRESET 10 kΩ PORESET SRESET HRESET 13 11 HRESET SRESET NVDD 10 kΩ 10 kΩ NVDD NVDD NVDD 1 3 5 7 9 11 2 4 6 8 10 12 4 61 5 15 TRST 2 kΩ 10 kΩ TRST VDD_SENSE NC CHKSTP_OUT NVDD CHKSTP_OUT 10 kΩ 10 kΩ NVDD NVDD CHKSTP_IN TMS 14 COP Header 2 KEY 13 No pin CHKSTP_IN 8 TMS 9 1 3 7 2 10 12 16 NC NC NC TDO TDI TCK 15 16 COP Connector Physical Pin Out TDO TDI TCK Notes: 1. Some systems require power to be fed from the application board into the debugger repeater card via the COP header. In this case the resistor value for VDD_SENSE should be around 20Ω. 2. Key location; pin 14 is not physically present on the COP header. Figure 42. JTAG Interface Connection MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 86 Freescale Semiconductor Document Revision History 22 Document Revision History Table 22-61 provides a revision history for this hardware specification. Table 65. Document Revision History Revision 0 Date 06/2007 Initial release. Substantive Change(s) 23 Ordering Information Ordering information for the parts fully covered by this specification document is provided in Section 23.1, “Part Numbers Fully Addressed by This Document.” 23.1 Part Numbers Fully Addressed by This Document Table 66 provides the Freescale part numbering nomenclature for the MPC8313E. Note that the individual part numbers correspond to a maximum processor core frequency. For available frequencies, contact your local Freescale sales office. In addition to the processor frequency, the part numbering scheme also includes an application modifier which may specify special application conditions. Each part number also contains a revision code which refers to the die mask revision number. Table 66. Part Numbering Nomenclature MPC Product Code MPC nnnn Part Identifier 8313 e Encryption Acceleration Blank = Not included E = included t Temperature Range 3 Blank = 0 to 105° C C= –40 to 105°C pp Package 1 VR= PB free TEPBGAII aa e300 core Frequency 2 a DDR Frequency x Revision Level Contact local Freescale sales office AF = 333MHz F = 333 MHz Notes: 1. See Section 18, “Package and Pin Listings,” for more information on available package types. 2. Processor core frequencies supported by parts addressed by this specification only. Not all parts described in this specification support all core frequencies. Additionally, parts addressed by Part Number Specifications may support other maximum core frequencies. 3. Contact local Freescale office on availability of parts with C temperature range MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 87 How to Reach Us: Home Page: www.freescale.com email: support@freescale.com USA/Europe or Locations Not Listed: Freescale Semiconductor Technical Information Center, CH370 1300 N. Alma School Road Chandler, Arizona 85224 1-800-521-6274 480-768-2130 support@freescale.com Europe, Middle East, and Africa: Freescale Halbleiter Deutschland GmbH Technical Information Center Schatzbogen 7 81829 Muenchen, Germany +44 1296 380 456 (English) +46 8 52200080 (English) +49 89 92103 559 (German) +33 1 69 35 48 48 (French) support@freescale.com Japan: Freescale Semiconductor Japan Ltd. Headquarters ARCO Tower 15F 1-8-1, Shimo-Meguro, Meguro-ku Tokyo 153-0064, Japan 0120 191014 +81 3 5437 9125 support.japan@freescale.com Asia/Pacific: Freescale Semiconductor Hong Kong Ltd. Technical Information Center 2 Dai King Street Tai Po Industrial Estate, Tai Po, N.T., Hong Kong +800 2666 8080 support.asia@freescale.com For Literature Requests Only: Freescale Semiconductor Literature Distribution Center P.O. Box 5405 Denver, Colorado 80217 1-800-441-2447 303-675-2140 Fax: 303-675-2150 LDCForFreescaleSemiconductor @hibbertgroup.com Information in this document is provided solely to enable system and software implementers to use Freescale Semiconductor products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document. Freescale Semiconductor reserves the right to make changes without further notice to any products herein. Freescale Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Freescale Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Freescale Semiconductor does not convey any license under its patent rights nor the rights of others. Freescale Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Freescale Semiconductor product could create a situation where personal injury or death may occur. Should Buyer purchase or use Freescale Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Freescale Semiconductor was negligent regarding the design or manufacture of the part. Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc. The Power Architecture and Power.org word marks and the Power and Power.org logos and related marks are trademarks and service marks licensed by Power.org. The described product contains a PowerPC processor core. The PowerPC name is a trademark of IBM Corp. and used under license. IEEE Stds. 802.1™, 802.11™, 802.2™, 802.3™, 1149.1™, and 1588™ are trademarks of the Institute of Electrical and Electronics Engineers, Inc., (IEEE). This product is not endosed or approved by the IEEE. All other product or service names are the property of their respective owners. © Freescale Semiconductor, Inc., 2007. Document Number: MPC8313EEC Rev. 0 06/2007