MPC94551EF

Freescale Semiconductor Technical Data MPC94551 Rev 3, 2/2005 Low Voltage 1:4 CMOS Clock Buffer The MPC94551 is a CMOS 1:4 fanout buffer. The MPC94551 is ideal for applications requiring lower voltage. Features • • • • • • • • 1:4 CMOS fanout buffer 300 ps output to output skew I/O frequency up to 160 MHz operation Non-inverting output clock 3.3 V supply voltage Output Enable mode tri-states outputs -40°C to 85°C industrial temperature range Standard 8-lead SOIC package 1:4 LVCMOS CLOCK BUFFER MPC94551 D SUFFIX 8-LEAD SOIC PACKAGE CASE 751-06 EF SUFFIX 8-LEAD SOIC PACKAGE Pb-FREE PACKAGE CASE 751-06 ORDERING INFORMATION Device MPC94551D MPC94551DR2 MPC94551EF MPC94551EFR2 Package SO-8 SO-8 SO-8 (Pb-FREE) SO-8 (Pb-FREE) Q1 ICLK 1 2 3 4 8 7 6 5 OE VDD GND Q4 Q2 ICLK Q3 Q1 Q2 Q4 Q3 OE Figure 1. Logic Diagram Figure 2. Pin Assignment © Freescale Semiconductor, Inc., 2005. All rights reserved. Table 1. Pin Description Pin Number 1 2 3 4 5 6 7 8 Pin Name ICLK Q1 Q2 Q3 Q4 GND VDD OE Pin Type Input Output Output Output Output Power Power Input Clock input, internal pull-up resistor Clock output(1) Clock output(1) Clock output(1) Clock output(1) Connect to ground(2) Connect to 3.3 V(2) Output enable, tri-states outputs when low, internal pull-up resistor Pin Description 1. A 33 Ω series terminating resistor may be used on each clock output if the trace is longer than 1 inch. 2. A decoupling capacitor of 0.01 µF should be connected between VDD on pin 7 and GND on pin 6, as close to the device as possible. Table 2. Absolute Maximum Ratings(1) Parameter Power Supply Voltage, VDD All Inputs and Outputs Ambient Operating Temperature Storage Temperature Junction Temperature Soldering Temperature Rating 3.9 –0.5 to VDD +0.5 –40 to +85 –65 to +150 175 260 Unit V V °C °C °C °C 1. Stresses above the ratings listed below can cause permanent damage to the device. These ratings are stress ratings only. Functional operation of the device at these or any other conditions above those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods can affect product reliability. Electrical parameters are guaranteed only over the recommended operating temperature range. Table 3. DC Characteristics (VDD = 3.3 V ± 5%; Ambient Temperature = –40°C to 85°C) Parameter Operating Voltage Input High Voltage(1), ICLK Input Low Voltage(1), ICLK Input High Voltage, OE Input Low Voltage, OE Ouput Low Voltage Output High Voltage Operating Supply Current Nominal Output Impedance Internal Pull-up Resistor Input Capacitance Symbol VDD VIH VIL VIH VIL VOL VOH IDD ZO RPU CIN CIN Short Circuit Current 1. Nominal switching threshold is VDD/2. IOS ICLK OE pin ICLK IOL = 12 mA IOH = –12 mA No load, 135 MHz 2.4 30 27 31 5 1 ±50 2 Conditions Min 3.15 VDD/2 + 0.7 Typ Max 3.45 3.8 VDD/2 – 0.7 VDD 0.8 0.4 Unit V V V V V V V mA Ω kΩ pF pF mA MPC94551 2 Advanced Clock Drivers Devices Freescale Semiconductor Table 4. AC Characteristics (VDD = 3.3 V ± 5%; Ambient Temperature = –40°C to 85°C) Parameter Input Frequency Output Frequency(1) Output Clock Rise Time Output Clock Fall Time Propagation Delay(2) tOR tOF 15 pF load 0.8 V to 2.0 V 2.0 V to 0.8 V 135 MHz Rising edges at VDD/2 1.5 4 Symbol Condition Min 0 Typ Max 160 160 1.5 1.5 5 300 Unit MHz MHz ns ns ns ps Output to Output Skew(3) 1. Measured with an external series resistor of 33Ω positioned close to each output pin 2. Measured with rail to rail input clock 3. Measured between any 2 outputs with equal loading PACKAGE DIMENSIONS A 8 D 5 C E 1 4 H 0.25 M B M NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. DIMENSIONS ARE IN MILLIMETER. 3. DIMENSION D AND E DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE. 5. DIMENSION B DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 TOTAL IN EXCESS OF THE B DIMENSION AT MAXIMUM MATERIAL CONDITION. MILLIMETERS MIN MAX 1.35 1.75 0.10 0.25 0.35 0.49 0.19 0.25 4.80 5.00 3.80 4.00 1.27 BSC 5.80 6.20 0.25 0.50 0.40 1.25 0˚ 7˚ h B C e A SEATING PLANE X 45˚ θ L 0.10 A1 B 0.25 M CB S A S DIM A A1 B C D E e H h L θ D/EF SUFFIX SOIC PACKAGE CASE 751-06 ISSUE T MPC94551 Advanced Clock Drivers Devices Freescale Semiconductor 3 How to Reach Us: Home Page: www.freescale.com E-mail: support@freescale.com USA/Europe or Locations Not Listed: Freescale Semiconductor Technical Information Center, CH370 1300 N. Alma School Road Chandler, Arizona 85224 +1-800-521-6274 or +1-480-768-2130 support@freescale.com Europe, Middle East, and Africa: Freescale Halbleiter Deutschland GmbH Technical Information Center Schatzbogen 7 81829 Muenchen, Germany +44 1296 380 456 (English) +46 8 52200080 (English) +49 89 92103 559 (German) +33 1 69 35 48 48 (French) support@freescale.com Japan: Freescale Semiconductor Japan Ltd. Headquarters ARCO Tower 15F 1-8-1, Shimo-Meguro, Meguro-ku, Tokyo 153-0064 Japan 0120 191014 or +81 3 5437 9125 support.japan@freescale.com Asia/Pacific: Freescale Semiconductor Hong Kong Ltd. Technical Information Center 2 Dai King Street Tai Po Industrial Estate Tai Po, N.T., Hong Kong +800 2666 8080 support.asia@freescale.com For Literature Requests Only: Freescale Semiconductor Literature Distribution Center P.O. Box 5405 Denver, Colorado 80217 1-800-441-2447 or 303-675-2140 Fax: 303-675-2150 LDCForFreescaleSemiconductor@hibbertgroup.com Information in this document is provided solely to enable system and software implementers to use Freescale Semiconductor products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document. Freescale Semiconductor reserves the right to make changes without further notice to any products herein. Freescale Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters that may be provided in Freescale Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”, must be validated for each customer application by customer’s technical experts. Freescale Semiconductor does not convey any license under its patent rights nor the rights of others. Freescale Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Freescale Semiconductor product could create a situation where personal injury or death may occur. Should Buyer purchase or use Freescale Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Freescale Semiconductor was negligent regarding the design or manufacture of the part. Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. © Freescale Semiconductor, Inc. 2005. All rights reserved. MPC94551 Rev. 3 2/2005