C232HM

Future Technology Devices International Ltd C232HM USB 2.0 Hi-Speed to MPSSE Cable Datasheet Document Reference No.: FT_000401 Version 1.0 Issue Date: 2011-07-21 Future Technology Devices International Limited (FTDI) Unit 1, 2 Seaward Place, Glasgow G41 1HH, United Kingdom Tel.: +44 (0) 141 429 2777 Fax: + 44 (0) 141 429 2758 E-Mail (Support): support1@ftdichip.com Web: http://www.ftdichip.com Use of FTDI devices in life support and/or safety applications is entirely at the user’s risk, and the user agrees to defend, indemnify and hold harmless FTDI from any and all damages, claims, suits or expense resulting from such use. © Copyright 2011 Future Technology Devices International Ltd Document Reference No.: FT_000401 USB 2.0 HI-SPEED TO MPSSE CABLE Datasheet Version 1.0 Clearance No.: FTDI# 214 1 Description The USB 2.0 Hi-Speed to MPSSE cable contains a small internal electronic circuit board, utilising the FTDI FT232H, which is encapsulated into the USB connector end of the cable, this handles all the USB signalling and protocols. The cable provides a fast, simple way to connect devices with 3.3 Volt digital interfaces to USB. For full details of the IC, consult the FT232H datasheet, this is available from DS_FT232H. The integrated FT232H device incorporates a command processor called the Multi -Protocol Synchronous Serial Engine (MPSSE). The purpose of the MPSSE command processor is to communicate with de vices which use synchronous protocols (such as JTAG, SPI or I2C) in an efficient manner. Full details are available in the MPSSE application note - AN_108. The cable is terminated by ten individual wires with single pole connectors which can be interfaced to a male header. Cable signals are compliant with CMOS logic at 3.3 volts. The FT232H is a single channel USB 2.0 Hi-Speed (480Mb/s) to UART/FIFO IC. It can be configured in a variety of industry standard serial or parallel interfaces, such as MPSSE - JTAG, SPI, I2C. The C232HM MPSSE cable is easily configured into each interface e.g. JTAG, SPI, I2C via the application software. The cable is powered from a USB host port and is USB 2.0 Hi-Speed compatible. The cable is 0.5m long and supports a data transfer up to 30Mbps in MPSSE mode. The C232HM MPSSE cable requires USB device drivers, available free from http://www.ftdichip.com. The D2XX driver is used with application software to directly access the FT232H in the cable though a DLL. This is illustrated in the Figure 1-1 The C232HM MPSSE cable uses the FTDI’s FT232H USB to serial IC device. Connector C232HM API USB 10 Female pin headers D2XX Software application access to USB via D 2 XX Figure 1-1 Using the C232HM MPSSE Cable Copyright © 2011 Future Technology Devices International Limited DLL 1 Document Reference No.: FT_000401 USB 2.0 HI-SPEED TO MPSSE CABLE Datasheet Version 1.0 Clearance No.: FTDI# 214 1.1 Available Cables and Part Numbers The following Table 1.1 gives details of the available C232HM MPSSE cables. Part Number Description USB to MPSSE cable with +3.3V digital level signals. Maximum End Connector Cable details 10 core, UL2464 24 AWG, Single pole, receptacle x 10 diam=6.5mm C232HM-DDHSL-0 output of 200mA @ 3.3VDC on VCC (see Note 1) USB to MPSSE cable with +3.3V digital level signals. Maximum 10 core, UL2464 24 AWG, Single pole, receptacle x 10 diam=6.5mm C232HM-EDHSL-0 output of 200mA @ 5.0VDC on VCC (see Note 2) Table 1.1 C232HM MPSSE Cable Descriptions and Part Numbers Note 1: The VCC power output signal (RED wire) is 3.3V. The source of 3.3V is the onboard regulator output, which is switched onto the power output signal. Note 2: The VCC power output signal (RED wire) is 5.0V. The source of 5.0V is the USB VBUS input, which is switched onto the power output signal. FTDI supports customised end connector designs. For more information, please contact your local FTDI sales office (see end of datasheet for contact details). 1.2 Certifications The FTDI C232HM MPSSE cables are fully RoHS, FCC and CE compliant. Copyright © 2011 Future Technology Devices International Limited 2 Document Reference No.: FT_000401 USB 2.0 HI-SPEED TO MPSSE CABLE Datasheet Version 1.0 Clearance No.: FTDI# 214 Table of Contents 1 Description ..................................................................................... 1 1.1 1.2 Available Cables and Part Numbers ............................................................... 2 Certifications ................................................................................................. 2 2 Typical Applications ........................................................................ 4 2.1 2.2 Driver Support .............................................................................................. 4 Features ........................................................................................................ 5 3 C232HM MPSSE Cable connection and Mechanical Details .............. 6 3.1 3.2 3.3 C232HM MPSSE Cable Signal Descriptions .................................................... 7 C232HM MPSSE Cable Signal Descriptions .................................................... 8 C232HM MPSSE Cable Electrical Parameters ................................................. 9 C232HM-DDHSL-0 Electrical Parameters ..................................................... 9 C232HM-EDHSL-0 Electrical Parameters ....................................................... 9 C232HM-DDHSL-0 and C232HM-EDHSL-0 I/O Characteristics ........................10 3.3.1 3.3.2 3.3.1 4 5 Cable PCB Circuit Schematic ......................................................... 11 Contact Information ..................................................................... 13 Appendix A - Cable EEPROM Configuration ......................................... 15 Appendix B - List of Figures and Tables ............................................. 16 Appendix C – Revision History ........................................................... 17 Copyright © 2011 Future Technology Devices International Limited 3 Document Reference No.: FT_000401 USB 2.0 HI-SPEED TO MPSSE CABLE Datasheet Version 1.0 Clearance No.: FTDI# 214 2 Typical Applications USB to JTAG interfaces USB to SPI interfaces USB to I C interfaces Interfacing MCU / PLD / FPGA based designs to USB USB Audio and Low Bandwidth Video data transfer 2 Rapid USB integration into existing electronic systems Prototyping platform for USB interface on new systems USB Instrumentation 2.1 Driver Support Royalty free D2XX Direct Drivers (USB Drivers + DLL S/W Interface) Windows 98, 98SE, ME, 2000, Server 2003, XP and Server 2008 Windows XP and XP 64-bit Windows 7 and Windows 7 64-bit Windows Vista and Vista 64-bit Windows CE 4.2, 5.0 and 6.0 Linux 2.4.20 and greater The drivers listed above are all available to download for free from http://www.ftdichip.com. Various Third-Party Drivers are also available for various other operating systems - see http://www.ftdichip.com/Support/Links.htm for details. Copyright © 2011 Future Technology Devices International Limited 4 Document Reference No.: FT_000401 USB 2.0 HI-SPEED TO MPSSE CABLE Datasheet Version 1.0 Clearance No.: FTDI# 214 2.2 Features Based on the Single chip USB Hi-Speed FT232H device USB 2.0 Hi-Speed (480Mbits/Second) and Full Speed (12Mbits/Second) compatible Entire USB protocol handled on the chip – No USB-specific firmware programming required USB Type A connector for direct connection to a host or hub USB bus powered Fully assisted hardware or X-On / X-Off software handshaking Synchronous Serial (MPSSE) data rates of up to 30Mbps on JTAG, SPI and I2C 1kByte receive and transmit buffers for high data throughput Transmit and receive LED drive signals Adjustable receive buffer timeout Support for USB suspend and resume Low operating and USB suspend current Low USB bandwidth consumption UHCI / OHCI / EHCI host controller compatible -40°C to +85°C operating temperature range Cable length is 0.5m (19.7 inch) Custom versions also available (subject to Minimum Order Quantity (MOQ)) FTDI’s royalty-free D2XX drivers eliminate the requirement for USB driver development in most cases Copyright © 2011 Future Technology Devices International Limited 5 Document Reference No.: FT_000401 USB 2.0 HI-SPEED TO MPSSE CABLE Datasheet Version 1.0 Clearance No.: FTDI# 214 3 C232HM MPSSE Cable connection and Mechanical Details The following Figure 3-1 shows the cable signals and the wire colours for these signals on the C232HM MPSSE cable. VCC TCK TDI TD0 TMS GPIOL0 GPIOL1 GPIOL2 GPIOL3 GND 1 2 3 4 5 6 7 8 9 10 CABLE 0.5m 1 2 3 RED ORANGE YELLOW GREEN BROWN GREY PURPLE WHITE BLUE BLACK 4 5 6 7 8 9 10 Figure 3-1 C232HM MPSSE Cable Connections (numbers refer to pad numbers on the PCB) Copyright © 2011 Future Technology Devices International Limited 6 Document Reference No.: FT_000401 USB 2.0 HI-SPEED TO MPSSE CABLE Datasheet Version 1.0 Clearance No.: FTDI# 214 3.1 C232HM MPSSE Cable Signal Descriptions Figure 3-2 C232HM MPSSE Cable Mechanical Details (dimensions in mm) Copyright © 2011 Future Technology Devices International Limited 42.5 16 7 Document Reference No.: FT_000401 USB 2.0 HI-SPEED TO MPSSE CABLE Datasheet Version 1.0 Clearance No.: FTDI# 214 3.2 C232HM MPSSE Cable Signal Descriptions Colour Red Gray Purple White Blue Black Pin Number 1 6 7 8 9 10 Name VCC GPIOL0 GPIOL1 GPIOL2 GPIOL3 GND Type Output Input/Output Input/Output Input/Output Input/Output GND Description Power Supply Output to target board. General Purpose input/output. General Purpose input/output. General Purpose input/output. General Purpose input/output. Device ground supply pin. Table 3.1 Common Cable Signal Descriptions Colour Orange Yellow Green Brown Pin Number 2 3 4 5 Name TCK TDI TDO TMS Type Output Input Output Output Description Test Interface Clock Test Data Input Test Data Output Test Mode Select Table 3.2 MPSSE Option JTAG - Signal Descriptions Colour Orange Yellow Green Brown Pin Number 2 3 4 5 Name SK DO DI CS Type Output Output Input Output Description Serial Clock Serial data output Serial Data Input Serial Chip Select Table 3.3 MPSSE Option SPI - Signal Descriptions Colour Orange Yellow Green Pin Number 2 3 4 Name SCL Type Output Description Serial Clock Serial data signal shorted together to create SDA Input/Output bidirectional data(both yellow and green wires need to be shorted together) Table 3.4 MPSSE Option I2C - Signal Descriptions Copyright © 2011 Future Technology Devices International Limited 8 Document Reference No.: FT_000401 USB 2.0 HI-SPEED TO MPSSE CABLE Datasheet Version 1.0 Clearance No.: FTDI# 214 3.3 C232HM MPSSE Cable Electrical Parameters 3.3.1 C232HM-DDHSL-0 Parameter VCC IO T Description Output Power Voltage Output Power Current Operating Temperature Range Electrical Parameters Minimum 3.2 -40 Typical 3.3 Maximum 3.6 200 +85 Units V mA o Conditions C Table 3.5 C232HM-DDHSL-0 Operating Parameters 3.3.2 C232HM-EDHSL-0 Electrical Parameters Parameter VCC IO Description Output Power Voltage Supply Current Operating Temperature Range Minimum 4.75 Typical 5 Maximum 5.25 200 Units V mA Must be less that 2.5mA during suspend. Conditions T -40 +85 o C Table 3.6 C232HM-EDHSL-0 Power Supply Output Parameters Copyright © 2011 Future Technology Devices International Limited 9 Document Reference No.: FT_000401 USB 2.0 HI-SPEED TO MPSSE CABLE Datasheet Version 1.0 Clearance No.: FTDI# 214 3.3.1 C232HM-DDHSL-0 and C232HM-EDHSL-0 I/O Characteristics Parameter Voh Description Output Voltage High Minimum 2.40 Typical 3.14 Maximum Units V Conditions Ioh = +/-2mA I/O Drive strength* = 4mA 3.20 3.22 V V I/O Drive strength* = 8mA I/O Drive strength* = 12mA I/O Drive strength* = 16mA Iol = +/-2mA 3.22 V Vol Output Voltage Low 0.18 0.40 V I/O Drive strength* = 4mA 0.12 0.08 V V I/O Drive strength* = 8mA I/O Drive strength* = 12mA I/O Drive strength* = 16mA LVTTL 0.07 Input low Switching Threshold Input High Switching Threshold Switching Threshold Schmitt trigger negative going threshold voltage Schmitt trigger positive going threshold voltage Input pull-up resistance Input pull-down resistance Input Leakage Current Tri-state output leakage current 40 40 15 0.80 2.00 V Vil - 0.80 V Vih Vt Vt- 1.50 1.10 - V V V LVTTL LVTTL Vt+ Rpu Rpd Iin Ioz 1.60 75 75 45 ±10 2.00 190 190 85 V KΩ KΩ μA μA Vin = 0 Vin =VCCIO Vin = 0 Vin = 5.5V or 0 Table 3.7 C232HD-DDHSP-0 and C232HD-EDHSP-0 I/O Pin Characteristics * The I/O drive strength and slow slew-rate are configurable in the EEPROM. The I/O pins are +3.3v cells, which are +5V tolerant Copyright © 2011 Future Technology Devices International Limited 10 Document Reference No.: FT_000401 USB 2.0 HI-SPEED TO MPSSE CABLE Datasheet Version 1.0 Clearance No.: FTDI# 214 4 Cable PCB Circuit Schematic The circuit schematics for the small internal electronic circuit board, utilising the FTDI FT232H, which is encapsulated into the USB connector end of the cable, are shown in Figure 4.1 Circuit Schematic of C232HM-DDHSL-0 and Figure 4.2 - Circuit Schematic of PCB - C232HM-EDHSL-0. Customised versions of these cables are also available. Users interested in customised versions of these cables should contact FTDI sales (sales1@ftdichip.com). Figure 4.1 Circuit Schematic of C232HM-DDHSL-0 Copyright © 2011 Future Technology Devices International Limited 11 Document Reference No.: FT_000401 USB 2.0 HI-SPEED TO MPSSE CABLE Datasheet Version 1.0 Clearance No.: FTDI# 214 Figure 4.2 - Circuit Schematic of PCB - C232HM-EDHSL-0 Copyright © 2011 Future Technology Devices International Limited 12 Document Reference No.: FT_000401 USB 2.0 HI-SPEED TO MPSSE CABLE Datasheet Version 1.0 Clearance No.: FTDI# 214 5 Contact Information Head Office – Glasgow, UK Future Technology Devices International Limited Unit 1, 2 Seaward Place, Centurion Business Park Glasgow, G41 1HH United Kingdom Tel: +44 (0) 141 429 2777 Fax: +44 (0) 141 429 2758 E-mail (Sales) E-mail (Support) E-mail (General Enquiries) Web Site URL Web Shop URL Branch Office – Taipei, Taiwan Future Technology Devices International Limited (Taiwan) 2F, No. 516, Sec. 1, NeiHu Road Taipei 114 Taiwan , R.O.C. Tel: +886 (0) 2 8797 1330 Fax: +886 (0) 2 8751 9737 E-mail (Sales) E-mail (Support) E-mail (General Enquiries) Web Site URL tw.sales1@ftdichip.com tw.support1@ftdichip.com tw.admin1@ftdichip.com http://www.ftdichip.com sales1@ftdichip.com support1@ftdichip.com admin1@ftdichip.com http://www.ftdichip.com http://www.ftdichip.com Branch Office – Hillsboro, Oregon, USA Future Technology Devices International Limited (USA) 7235 NW Evergreen Parkway, Suite 600 Hillsboro, OR 97123-5803 USA Tel: +1 (503) 547 0988 Fax: +1 (503) 547 0987 E-Mail (Sales) E-mail (Support) E-mail (General Enquiries) Web Site URL us.sales@ftdichip.com us.support@ftdichip.com us.admin@ftdichip.com http://www.ftdichip.com Branch Office – ShangHai, China Future Technology Devices International Limited (China) Room 408, 317 Xianxia Road, ChangNing District, ShangHai, P.R. China Tel: +86 (21) 62351596 Fax: +86 (21) 62351595 E-Mail (Sales) E-mail (Support) E-Mail (General Enquiries) Web Site URL cn.sales@ftdichip.com cn.support@ftdichip.com cn.admin@ftdichip.com http://www.ftdichip.com Distributor and Sales Representatives Please visit the Sales Network page of the FTDI Web site for the contact details of our distributor(s) and sales representative(s) in your country. Copyright © 2011 Future Technology Devices International Limited 13 Document Reference No.: FT_000401 USB 2.0 HI-SPEED TO MPSSE CABLE Datasheet Version 1.0 Clearance No.: FTDI# 214 System and equipment manufacturers and designers are responsible to ensure that their systems, and any Future Technology Devices International Ltd (FTDI) devices incorporated in their systems, meet all applicable safety, regulatory and system-level performance requirements. All application-related information in this document (including application descriptions, suggested FTDI devices and other materials) is provided for reference only. While FTDI has taken care to assure it is accurate, this information is subject to customer confirmation, and FTDI disclaims all liability for system designs and for any applications assistance provided by FTDI. Use of FTDI devices in life support and/or safety applications is entirely at the user’s risk, and the user agrees to defend, indemnify and hold harmless FTDI from any and all damages, claims, suits or expense resulting from such use. This document is subject to change without notice. No freedom to use patents or other intellectual property rights is implied by the publication of this document. Neither the whole nor any part of the information contained in, or the product described in this document, may be adapted or reproduced in any material or electronic form without the prior written consent of the copyright holder. Future Technology Devices International Ltd, Unit 1, 2 Seaward Place, Centurion Business Park, Glasgow G41 1HH, United Kingdom. Scotland Registered Company Number: SC136640. Copyright © 2011 Future Technology Devices International Limited 14 Document Reference No.: FT_000401 USB 2.0 HI-SPEED TO MPSSE CABLE Datasheet Version 1.0 Clearance No.: FTDI# 214 Appendix A - Cable EEPROM Configuration Each C232HM MPSSE cable is controlled by the FTDI FT232H IC. This FT232H device contains an EEPROM which contains the USB configuration descriptors for that device. When the cable is plugged into a PC or a USB reset is performed, the PC will read these descriptors. The default values stored into the internal EEPROM are defined in the following table Parameter USB Vendor ID (VID) USB Product UD (PID) Serial Number Enabled? Serial Number Manufacturer Name Value 0403h 6014h Yes A unique serial number is generated and programmed into See Note FTDI Product description depends on the cable. The following lists a the Product descriptions for each different cable. Product Description See note C232HM-VSW3V3 C232HM-VSW5V0 Max Bus Power Current Power Source Device Type USB Version Remote Wake Up High Current I/Os Invert TXD Invert RXD Invert RTS# Invert CTS# 500mA Bus Powered FT232H Returns USB 2.0 device description to the host. 0200 Disabled Enabled Disabled Disabled Disabled Disabled Note: The device is a USB 2.0 Hi-Speed device (480Mb/s). 500uA suspend limit when in this state Enables the high drive level on the CBUS I/O pins. Signal on this pin becomes TXD# if enable. Signal on this pin becomes RXD# if enable. Signal on this pin becomes RTS if enable. Signal on this pin becomes CTS if enable. Includes power available from the cable plus power required for the FT232H the EEPROM during device final test. FTDI default VID (hex) FTDI default PID (hex) Notes Default Internal EEPROM Configuration The internal EEPROM in the cable can be re-programmed over USB using the utility program FT_PROG. Both can be downloaded from www.ftdichip.com. Copyright © 2011 Future Technology Devices International Limited 15 Document Reference No.: FT_000401 USB 2.0 HI-SPEED TO MPSSE CABLE Datasheet Version 1.0 Clearance No.: FTDI# 214 Appendix B - List of Figures and Tables List of Figures Figure 1-1 Using the C232HM MPSSE Cable ................................................................ 1 Figure 4-1 C232HM MPSSE Cable Connections (numbers refer to pad numbers on the PCB) ........................................................................................................................... 6 Figure 4-2 C232HM MPSSE Cable Mechanical Details (dimensions in mm) ................ 7 Figure 5.1 Circuit Schematic of C232HM-DDHSL-0.................................................... 11 Figure 5.2 - Circuit Schematic of PCB - C232HM-EDHSL-0 ........................................ 12 List of Tables Table 1.1 C232HM MPSSE Cable Descriptions and Part Numbers ................................ 2 Table 4.1 Common Cable Signal Descriptions ............................................................. 8 Table 4.2 MPSSE Option JTAG - Signal Descriptions ................................................... 8 Table 4.3 MPSSE Option SPI - Signal Descriptions ...................................................... 8 Table 4.4 MPSSE Option I2C - Signal Descriptions ...................................................... 8 Table 4.2 C232HM-DDHSL-0 Operating Parameters .................................................. 9 Table 4.4 C232HM-EDHSL-0 Power Supply Output Parameters................................. 9 Table 4.3 C232HD-DDHSP-0 and C232HD-EDHSP-0 I/O Pin Characteristics ............. 10 Copyright © 2011 Future Technology Devices International Limited 16 Document Reference No.: FT_000401 USB 2.0 HI-SPEED TO MPSSE CABLE Datasheet Version 1.0 Clearance No.: FTDI# 214 Appendix C – Revision History Version 1.0 First Release 21st July 2011 Copyright © 2011 Future Technology Devices International Limited 17