RPI-HUB-MODULE

RPi HUB Module Datasheet Version 1.0 Document Reference No.: FT_000700 Clearance No.: FTDI# 297 Future Technology Devices International Ltd Datasheet RPi HUB Module Datasheet RPi HUB Module connects to a Raspberry-Pi computer and expands the number of interfaces that can be accessed downstream from a Host. RPi HUB Module also provides a dual channel USB UART/245FIFO/SPI/I2C/JTAG/GPIO interface converter. 1 Introduction The FT2232H based RPi HUB Module is a USB to UART/245FIFO/SPI/I2C/JTAG/GPIO interface expansion module targeted at connecting to Raspberry-Pi computer to expand the number of interfaces. However, it is not limited to this application. It can also be used as a hub device or an FT2232H evaluation module. The module has a USB 2.0 Hi-Speed hub chip which supports up to three external downstream USB ports: 2 via a dual USB connector and 1 via the DIL connector pins. Additionally, by utilising the FT2232H USB Hi-Speed dual-port bridge chip which handles all the USB signalling and protocols, the module can easily support up to two flexible interfacing ports. It is ideal for development purposes to quickly prove functionality of adding USB to a target design. This module utilises the GL850G USB 2.0 hub controller which provides a low-cost and widely used USB 2.0 hub solution, to provide up to 4 downstream USB ports. The GL850G is a single chip USB hub solution. The GL850G is a full function solution which supports both Individual/Gang power management modes and twocolour (green/amber) status LED. The FT2232H used on the Module is FTDI’s 5th generation of USB devices. The FT2232H is a USB 2.0 HiSpeed (480Mb/s) to UART/MPSSE IC. The device features two interfaces that can be configured for asynchronous or synchronous serial communications or Parallel FIFO Interface. The two interfaces can also be independently configured via an MPSSE engine. This allows the FT2232H to operate as two UART/Bit-Bang ports or two MPSSE engines which can be used to emulate JTAG, SPI, I2C, Bit-bang or other synchronous serial modes. All I/Os of the RPi HUB Module operate at 3.3V TTL and are 5V safe. FT2232H’s MPSSE interfaces are controlled over USB, for details on MPSSE see: Application Note AN_108. For more details on FT2232H see: FT2232H datasheet DS_FT2232H. 1.1 Ordering Information Product Name Order Code Description RPi HUB Module RPi-HUB-Module USB HUB and USB to dual channel multi interface converter module designed for Raspberry Pi. Table 1.1 – Ordering Information Use of FTDI devices in life support and/or safety applications is entirely at the user’s risk, and the user agrees to defend, indemnify and hold harmless FTDI from any and all damages, claims, suits or expense resulting from such use. RPi HUB Module Datasheet Version 1.0 Document Reference No.: FT_000700 Clearance No.: FTDI# 297 Table of Contents 1 Introduction ................................................................................... 1 1.1 2 3 Ordering Information .................................................................................... 1 Product Details ............................................................................... 3 2.1 Features ........................................................................................................ 3 2.2 Driver Support .............................................................................................. 3 2.3 Functions Overview ....................................................................................... 4 Pin Out and Signal Description ....................................................... 5 3.1 Module Connector Descriptions ..................................................................... 5 3.2 FT2232H Pin and Signal Descriptions ............................................................ 6 3.3 Module Pin and Signal Descriptions ............................................................... 7 4 Guide to Supplying Power .............................................................. 9 5 Mechanical Details ........................................................................ 10 6 Schematic Diagram....................................................................... 11 7 Contact Information ..................................................................... 13 Appendix A – FT2232H EEPROM Configuration ...................................................... 14 Appendix B – References....................................................................................... 15 Appendix C – List of Figures and Tables ................................................................ 15 List of Figures ....................................................................................................... 15 List of Tables ......................................................................................................... 15 Appendix D – Revision History .............................................................................. 16 2 Copyright © 2012 Future Technology Devices International Limited RPi HUB Module Datasheet Version 1.0 Document Reference No.: FT_000700 2 Clearance No.: FTDI# 297 Product Details 2.1 Features The RPi HUB Module has the following features: General:  USB 2.0 Hi-Speed compatible   One standard USB type A plug to connect to the Host UART data transfer rates from 300 baud to 12 Mbaud at 3.3V TTL levels   USB Hi-Speed FT2232H device for USBSerial/Bit bang communications. Entire USB protocol handled by USB module Synchronous Serial (MPSSE) data rates of up to 30Mbps on JTAG, SPI and I2C   USB 2.0 Hi-Speed hub controller integrated to support up to 3 downstream USB ports One dual-port USB type A connector and 0.1” pitch header to support up to 3 downstream USB ports   External power input connector available to supply external downstream USB ports. Green/Red status LED for downstream USB port 1 & 2.   Support for USB suspend and resume LED indicating power supply to external downstream USB ports  Defaults to two independent UART interfaces.  On-board EEPROM 93LC56 for FT2232H configuration  All I/O pins are 5V Safe  UHCI / OHCI / EHCI host controller compatible 2.2 Driver Support Royalty-Free VIRTUAL COM PORT (VCP) DRIVERS for: Royalty-Free D2XX Direct Drivers (USB Drivers + DLL S/W Interface):  Windows 7 32,64-bit  Windows 7 32,64-bit  Windows Vista  Windows Vista  Windows XP 32,64-bit  Windows XP 32,64-bit  Windows XP Embedded  Windows XP Embedded  Windows CE.NET 4.2 , 5.0 and 6.0  Windows CE.NET 4.2, 5.0 and 6.0  MAC OS OS-X  MAC OS OS-X  Linux 2.6.32 or later  Linux 2.6.32 or later  ARM Linux  ARM Linux  Android  Android The drivers listed above are all available to download for free from www.ftdichip.com. Various 3rd Party Drivers are also available for various other operating systems - visit www.ftdichip.com for details. For driver installation instructions please see: http://www.ftdichip.com/Support/Documents/InstallGuides.htm. 3 Copyright © 2012 Future Technology Devices International Limited RPi HUB Module Datasheet Version 1.0 Document Reference No.: FT_000700 Clearance No.: FTDI# 297 2.3 Functions Overview A block diagram of RPi HUB Module is illustrated in Figure 1.2. USB 2X12 Pin 2.54mm Male DIL Connector Channel A USB Type A Plug FT2232H GL850 Hi-Speed USB to Dual Channel Serial Data Converter 4 Channel Hi-Speed USB HUB USB Channel B Dual USB Type A Connector USB USB Connects to Mouse/Keyboard/ etc. USB Connects to RPi 2X12 Pin 2.54mm Male DIL Connector Figure 1.2 – Block diagram of RPi HUB Module The block diagram Figure 1.2 illustrates: the RPi HUB Module routes the signals from the GL850G and FT2232H devices to two 2X12-pin, 0.1”, headers and a dual-port USB type A connector. This allows easy connection to most PCB header sockets and ribbon cables. To use the FT2232H connected to a RPi. The RPi operating system by default includes the necessary virtual com port (VCP) drivers to access both ports of the FT2232H through the TTY. FTDI D2XX drivers, which allow access to the FT2232H through a DLL, are available for free by clicking here. For more information on FTDI drivers see: http://www.ftdichip.com/Drivers/D2XX.htm. The main target application for the RPi HUB Module is that it can be attached to a Raspberry-Pi computer as an expansion module. The RPi HUB Module expands the interfaces of Raspberry-Pi computer with up to 3 USB ports or 2 serial ports. More information is available on the Raspberry-Pi computer at http://www.Raspberry-Pi pi.org/ 4 Copyright © 2012 Future Technology Devices International Limited RPi HUB Module Datasheet Version 1.0 Document Reference No.: FT_000700 3 Clearance No.: FTDI# 297 Pin Out and Signal Description 3.1 Module Connector Descriptions Figure 3.1 – RPi HUB Module Connector Description (Top View) RPi HUB Module has 4 connectors on the board. The detailed descriptions of these connectors are listed in Table 3.1. Reference Designator CN1 CN2 CN3 Description USB type A signal connector to connect to the host port Dual-port USB type A connector to connect 2 downstream USB devices +5V power input from external PSU to power the module. J1 0.1” 2X12-pin header J2 0.1” 2X12-pin header Table 3.1 – RPi HUB Module Connector Descriptions A detailed description of each pin out is given in the next section. 5 Copyright © 2012 Future Technology Devices International Limited RPi HUB Module Datasheet Version 1.0 Document Reference No.: FT_000700 Clearance No.: FTDI# 297 3.2 FT2232H Pin and Signal Descriptions A list of functions available for every signal pin of the FT2232H is given in Figure 3.1. FT2232H Pin Pin functions depend on EEPROM configuration UART 245 FIFO SYNC 245 FIFO ASYNC Bit-bang SYNC Bit-bang Channel A CPU Style FIFO Host Bus Emulation D0 AD0 D1 AD1 Pin # Pin Name 16 ADBUS0 TXD D0 D0 D0 D0 TCK/SK 17 ADBUS1 RXD D1 D1 D1 D1 TDI/DO 18 ADBUS2 RTS# D2 D2 D2 D2 TDO/DI D2 AD2 19 ADBUS3 CTS# D3 D3 D3 D3 TMS/CS D3 AD3 21 ADBUS4 DTR# D4 D4 D4 D4 GPIOL0 D4 AD4 22 ADBUS5 DSR# D5 D5 D5 D5 GPIOL1 D5 AD5 23 ADBUS6 DCD# D6 D6 D6 D6 GPIOL2 D6 AD6 24 ADBUS7 RI# D7 D7 D7 D7 GPIOL3 D7 AD7 26 ACBUS0 TXDEN RXF# RXF# ** ** GPIOH0 CS# A8 27 ACBUS1 ** TXE# TXE# WRSTB# WRSTB# GPIOH1 A0 A9 28 ACBUS2 ** RD# RD# RDSTB# RDSTB# GPIOH2 RD# A10 29 ACBUS3 RXLED# WR# WR# GPIOH3 WR# A11 30 ACBUS4 TXLED# SIWUA SIWUA SIWUA GPIOH4 SIWUA A12 32 ACBUS5 ** CLKOUT ** ** ** GPIOH5 ** A13 33 ACBUS6 ** OE# ** ** ** GPIOH6 ** A14 34 ACBUS7 ** ** ** ** GPIOH7 ** A15 CS# ** SIWUA ** ** MPSSE Fast Serial interface USES CHANNEL B Channel B 38 BDBUS0 TXD D0 D0 D0 TCK/SK FSDI D0 39 40 BDBUS1 RXD D1 D1 D1 TDI/DO FSCLK D1 ALE BDBUS2 RTS# D2 D2 D2 TDO/DI FSDO D2 RD# 41 43 BDBUS3 CTS# D3 D3 D3 TMS/CS FSCTS D3 WR# BDBUS4 DTR# D4 D4 D4 GPIOL0 D4 IORDY 44 45 BDBUS5 DSR# D5 D5 D5 GPIOL1 D5 CLKOUT BDBUS6 DCD# D6 D6 D6 GPIOL2 D6 I/O0 46 BDBUS7 RI# D7 D7 D7 GPIOL3 D7 I/O1 48 BCBUS0 TXDEN RXF# ** ** GPIOH0 CS# ** 52 BCBUS1 ** TXE# WRSTB# WRSTB# GPIOH1 A0 ** 53 BCBUS2 ** RD# RDSTB# RDSTB# GPIOH2 RD# ** 54 BCBUS3 RXLED# WR# GPIOH3 WR# ** 55 BCBUS4 TXLED# SIWUB SIWUB ** 57 BCBUS5 ** ** ** ** GPIOH5 ** ** 58 BCBUS6 ** PWRSAV # ** ** ** GPIOH6 ** ** PWRSAV # PWRSAV# PWRSAV# PWRSAV# GPIOH7 PWRSAV# PWRSAV# ** SIWUB ** SIWUB GPIOH4 SIWUB 59 BCBUS7 60 PWREN# PWREN# PWREN# PWREN# PWREN# PWREN# PWREN# PWREN# PWREN# 36 SUSPEND# SUSPEND # SUSPEND # SUSPEND # SUSPEND # SUSPEND # SUSPEND # SUSPEND # SUSPEND # 63 EECS 62 EECLK Configuration memory interface 61 EEDATA Table 3.2 – FT2232H Functions Table 6 Copyright © 2012 Future Technology Devices International Limited PWRSAV# PWREN# SUSPEND# RPi HUB Module Datasheet Version 1.0 Document Reference No.: FT_000700 Clearance No.: FTDI# 297 3.3 Module Pin and Signal Descriptions The pin descriptions of J1 and J2 are given in Table 3.2 and Table 3.3. Connector Pin Name Description J1-1 AC7 FT2232H ACBUS7 pin J1-2 AC6 FT2232H ACBUS6 pin J1-3 AC5 FT2232H ACBUS5 pin J1-4 AC4 FT2232H ACBUS4 pin J1-5 AC3 FT2232H ACBUS3 pin J1-6 AC2 FT2232H ACBUS2 pin J1-7 AC1 FT2232H ACBUS1 pin J1-8 AC0 FT2232H ACBUS0 pin J1-9 AD7 FT2232H ADBUS7 pin J1-10 AD6 FT2232H ADBUS6 pin J1-11 AD5 FT2232H ADBUS5 pin J1-12 AD4 FT2232H ADBUS4 pin J1-13 AD3 FT2232H ADBUS3 pin J1-14 AD2 FT2232H ADBUS5 pin J1-15 AD1 FT2232H ADBUS1 pin J1-16 AD0 FT2232H ADBUS0 pin J1-17 SUSPEND# FT2232H SUSPEND# pin J1-18 GND J1-19 PWRN# FT2232H PWREN# pin J1-20 RESET# FT2232H RESET# pin J1-21 PAMBER4 J1-22 PGREEN4 J1-23 DP4 USB hub downstream port 4 D+ signal pin J1-24 DM4 USB hub downstream port 4 D- signal pin Ground USB hub downstream port 4 Overcurrent LED indicator signal pin USB hub downstream port 4 LED Traffic indicator signal pin Table 3.2 – RPi HUB Module Connection – J1 7 Copyright © 2012 Future Technology Devices International Limited RPi HUB Module Datasheet Version 1.0 Document Reference No.: FT_000700 Connector Pin Name J2-1 BD0 FT2232H BDBUS0 pin J2-2 BD1 FT2232H BDBUS1 pin J2-3 BD2 FT2232H BDBUS2 pin J2-4 BD3 FT2232H BDBUS3 pin J2-5 BD4 FT2232H BDBUS4 pin J2-6 BD5 FT2232H BDBUS5 pin J2-7 BD6 FT2232H BDBUS6 pin J2-8 BD7 FT2232H BDBUS7 pin J2-9 BC0 FT2232H BCBUS0 pin J210 BC1 FT2232H BCBUS1 pin J2-11 BC2 FT2232H BCBUS2 pin J2-12 BC3 FT2232H BCBUS3 pin J2-13 BC4 FT2232H BCBUS4 pin J2-14 BC5 FT2232H BCBUS5 pin J2-15 BC6 FT2232H BCBUS6 pin J2-16 BC7 FT2232H BCBUS7 pin J2-17 DATA FT2232H EEDATA pin J2-18 GND Ground J2-19 CLK FT2232H EECLK pin J2-20 VCCSW J2-21 CS J2-22 VCC3V3 J2-23 VBUS J2-24 VCC5V Clearance No.: FTDI# 297 Description Switchable power sourced from VBUS FT2232H EECS pin 3.3VDC generated from VCC (output) USB +5V VBUS power pin (output) from upstream USB port +5v power pin. Table 3.3 – RPi HUB Module Connection – J2 8 Copyright © 2012 Future Technology Devices International Limited RPi HUB Module Datasheet Version 1.0 Document Reference No.: FT_000700 Clearance No.: FTDI# 297 In most cases, the FT2232H pin is connected directly to the associated pin on J1 or J2. There are also several LEDs available on the FT2232H Hub-I/O to indicate the status of power and USB hub port. Detailed functions of LEDs are described in Table 3.4. LED Reference Colour Designator Function Description POWER Yellow Power active to downstream USB ports indicator PORT1 Red Overcurrent status of downstream USB port 1 indicator PORT1 Green Enumeration status of downstream USB port 1 indicator PORT2 Green Enumeration status of downstream USB port 2 indicator PORT2 Red Overcurrent status of downstream USB port 2 indicator Figure 3.4 – Functions of status LEDs on the module 4 Guide to Supplying Power When RPi HUB Module is connected to Raspberry Pi board it must be powered from external +5V power supply. The Raspberry Pi board can be powered by connecting P1-02 header to J2-24 on RPi HUB Module. To date, the Raspberry Pi uses a 140mA fuse on the power line to the USB connector; this fuse will not allow an adequate amount of current to power the RPi HUB Module from this USB connector. USB Bus powered configuration may be used with other host devices, such as PCs or laptops. To enable external power supply feature, switch the jumper JP1 and JP2 to SELF position, pins 2 & 3 shorted for both jumpers. The maximum total current consumed by the external USB devices on downstream port 1 and 2 is 1A. If the total current exceeds 1A, the fuse on the RPi HUB Module will disconnect the power to the USB downstream ports. If this occurs then LEDs PORT1 and PORT2 on the module will illuminate red to indicate over-current status. When powered from USB bus power, the estimated current consumed by the circuits on the module is between 100-300mA depending on the application. User should ensure that the host can supply this current via USB potation. 9 Copyright © 2012 Future Technology Devices International Limited RPi HUB Module Datasheet Version 1.0 Document Reference No.: FT_000700 5 Clearance No.: FTDI# 297 Mechanical Details 2.54 The mechanical details of the RPi HUB Module are shown in Figure 5.1: 16.21 3.77 CN2 13.07 GL850G 33.45 CN1 25.4 FT2232H 4.39 RPi Hub Module 12 5.88 2.15 CN3 8.89 JP1 JP2 1.22 14.71 12.55 65 15.8 5.3 10.8 4.82 1.7 Figure 5.1 – RPi HUB Module Dimensions diagram All dimensions are in millimetres. The headers J1 and J2 are mounted to the top of the PCB and the overall height is 10.8mm, with a body which exposes 5.3mm of the pins. The pins are 0.025 inch square. 10 Copyright © 2012 Future Technology Devices International Limited RPi HUB Module Datasheet Version 1.0 Document Reference No.: FT_000700 6 Clearance No.: FTDI# 297 Schematic Diagram Figure 6.1 – RPi HUB Module Schematic Part 1 of 2 11 Copyright © 2012 Future Technology Devices International Limited RPi HUB Module Datasheet Version 1.0 Document Reference No.: FT_000700 Clearance No.: FTDI# 297 Figure 6.2 – RPi HUB Module Schematic Part 2 of 2 12 Copyright © 2012 Future Technology Devices International Limited RPi HUB Module Datasheet Version 1.0 Document Reference No.: FT_000700 7 Clearance No.: FTDI# 297 Contact Information Head Office – Glasgow, UK Branch Office – Hillsboro, Oregon, USA Future Technology Devices International Limited Unit 1, 2 Seaward Place, Centurion Business Park Glasgow G41 1HH United Kingdom Tel: +44 (0) 141 429 2777 Fax: +44 (0) 141 429 2758 Future Technology Devices International Limited (USA) 7235 NW Evergreen Parkway, Suite 600 Hillsboro, OR 97123-5803 USA Tel: +1 (503) 547 0988 Fax: +1 (503) 547 0987 E-mail (Sales) E-mail (Support) E-mail (General Enquiries) E-Mail (Sales) E-Mail (Support) E-Mail (General Enquiries) sales1@ftdichip.com support1@ftdichip.com admin1@ftdichip.com us.sales@ftdichip.com us.support@ftdichip.com us.admin@ftdichip.com Branch Office – Taipei, Taiwan Branch Office – Shanghai, China Future Technology Devices International Limited (Taiwan) 2F, No. 516, Sec. 1, NeiHu Road Taipei 114 Taiwan , R.O.C. Tel: +886 (0) 2 8791 3570 Fax: +886 (0) 2 8791 3576 Future Technology Devices International Limited (China) Room 1103, No. 666, West Huaihai Road, Shanghai, 200052 China Tel: +86 21 62351596 Fax: +86 21 62351595 E-mail (Sales) E-mail (Support) E-mail (General Enquiries) asia.sales1@ftdichip.com asia.support1@ftdichip.com asia.admin1@ftdichip.com E-mail (Sales) E-mail (Support) E-mail (General Enquiries) cn.sales@ftdichip.com cn.support@ftdichip.com cn.admin@ftdichip.com Web Site http://ftdichip.com Distributor and Sales Representatives Please visit the Sales Network page of the FTDI Web site for the contact details of our distributor(s) and sales representative(s) in your country. System and equipment manufacturers and designers are responsible to ensure that their systems, and any Future Technology Devices International Ltd (FTDI) devices incorporated in their systems, meet all applicable safety, regulatory and system-level performance requirements. All application-related information in this document (including application descriptions, suggested FTDI devices and other materials) is provided for reference only. While FTDI has taken care to assure it is accurate, this information is subject to customer confirmation, and FTDI disclaims all liability for system designs and for any applications assistance provided by FTDI. Use of FTDI devices in life support and/or safety applications is entirely at the user’s risk, and the user agrees to defend, indemnify and hold harmless FTDI from any and all damages, claims, suits or expense resulting from such use. This document is subject to change without notice. No freedom to use patents or other intellectual property rights is implied by the publication of this document. Neither the whole nor any part of the information contained in, or the product described in this document, may be adapted or reproduced in any material or electronic form without the prior written consent of the copyright holder. Future Technology Devices International Ltd, Unit 1, 2 Seaward Place, Centurion Business Park, Glasgow G41 1HH, United Kingdom. Scotland Registered Company Number: SC136640 13 Copyright © 2012 Future Technology Devices International Limited RPi HUB Module Datasheet Version 1.0 Document Reference No.: FT_000700 Clearance No.: FTDI# 297 Appendix A – FT2232H EEPROM Configuration The RPi HUB Module utilizes an EEPROM which contains the USB configuration descriptors for the FT2232H. When the RPi HUB Module is plugged into a PC or a USB reset is performed, the PC will read these descriptors. The default values stored into the EEPROM are defined in Table 7.1. Parameter Value Notes USB Vendor ID (VID) 0403h FTDI default VID (hex) USB Product UD (PID) 6010h FTDI default PID (hex) Serial Number Enabled? Yes Serial Number See Note Pull down I/O Pins in USB Suspend Manufacturer Name Product Description A unique serial number is generated and programmed into the EEPROM during device final test. Enabling this option will make the device pull down on the Disabled UART interface lines when the power is shut off (PWREN# is high). FTDI FT2232H RPi HUB Module Max Bus Power Current 90mA Power Source Bus Powered Device Type FT2232 USB Version 0200 Remote Wake Up Enabled High Current I/Os Enabled Load VCP Driver Enabled Returns USB 2.0 device description to the host. Taking RI# low will wake up the USB host controller from suspend. Enables the high drive level on the I/O pins Makes the device load the VCP driver interface for the device. Table 7.1 – Default Internal EEPROM Configuration The EEPROM for FT2232H chip on the RPi HUB Module can be re-programmed over USB using the utility program FT_Prog. FT_Prog can be downloaded from http://www.ftdichip.com/Support/Utilities.htm. Users who do not have their own USB Vendor ID but who would like to use a unique Product ID in their design can apply to FTDI for a free block of unique PIDs. Contact FTDI support for this service. Copyright © 2012 Future Technology Devices International Limited 14 RPi HUB Module Datasheet Version 1.0 Document Reference No.: FT_000700 Clearance No.: FTDI# 297 Appendix B – References FT2232H Datasheet Application and Technical Notes Appendix C – List of Figures and Tables List of Figures Figure 3.1 – RPi HUB Module Connector Description (Top View) .............................................................. 5 Figure 5.1 – RPi HUB Module Dimensions diagram ................................................................................... 10 Figure 6.1 – RPi HUB Module Schematic Part 1 of 2 .................................................................................. 11 Figure 6.2 – RPi HUB Module Schematic Part 2 of 2 .................................................................................. 12 List of Tables Table 1.1 – Ordering Information ................................................................................................................... 1 Table 3.1 – RPi HUB Module Connector Descriptions ................................................................................. 5 Table 3.2 – FT2232H Functions Table............................................................................................................ 6 Table 7.1 – Default Internal EEPROM Configuration .................................................................................. 14 Copyright © 2012 Future Technology Devices International Limited 15 RPi HUB Module Datasheet Version 1.0 Document Reference No.: FT_000700 Clearance No.: FTDI# 297 Appendix D – Revision History Document Title: Document Reference No.: Clearance No.: Document Folder: Document Feedback: Version 1.0 RPi HUB Module Datasheet FT_000700 FTDI# 297 FT2232H Send Feedback Initial Datasheet Released Copyright © 2012 Future Technology Devices International Limited 15/06/12 16