TTL-232RG-VREG1V8-WE

TTL to USB Serial Converter Generic Cables Datasheet Version 1.5 Document Reference No.: FT_000188 Clearance No.: FTDI# 129 Future Technology Devices International Ltd TTL-232RG TTL to USB Serial Converter Generic Cables Datasheet Version 1.5 Issue Date: 2018-05-04 Neither the whole nor any part of the information contained in, or the product described in this manual, may be adapted or reproduced in any material or electronic form without the prior written consent of the copyright holder. This product and its documentation are supplied on an as-is basis and no warranty as to their suitability for any particular purpose is either made or implied. Future Technology Devices International Ltd will not accept any claim for damages howsoever arising as a result of use or fa ilure of this product. Your statutory rights are not affected. This product or any variant of it is not intended for use in any medical appliance, device or system in which the failure of the product might reasonably be expected to result in personal injury. This document provides preliminary information that may be subject to change without notice. No freedom to use patents or other intellectual property rights is implied by the publication of this document. Future Technology Devices International Ltd, Unit 1, 2 Seaward Place, Centurion Business Park, Glasgow, G41 1HH, United Kingdom. Scotland Registered Number: SC136640 Copyright © Future Technology Devices International Limited 1 TTL to USB Serial Converter Generic Cables Datasheet Version 1.5 Document Reference No.: FT_000188 Clearance No.: FTDI# 129 1 Introduction The TTL-232RG generic cables are a family of USB to TTL serial UART converter cables incorporating FTDI’s FT232RQ USB to Serial UART interface IC device which handles all the USB signalling and protocols. The cables provide a fast, simple way to connect devices with a logic level serial interface to USB. Each TTL-232RG generic cable contains a small internal electronic circuit board, utilising the FT232R, which is encapsulated into the USB connector end of the cable. The FT232R datasheet is available at http://www.ftdichip.com/Support/Documents/DataSheets.htm. The other end of the cable is wire ended. The cables can be used for “TTL” or interface logic over a range to voltage levels. Cables are FCC, CE, and RoHS compliant at TTL levels of + 5V to + 1.8V. The USB side of the cable is USB powered and is USB 2.0 full speed compatible. Each cable is 1.8m long and supports a data transfer rate up to 3 Mbaud. Each cable supports the FTDIChip-ID™, with a unique USB serial number programmed into the FT232R. This feature can be used to create a security or password protected file transfer access using the cable. Further information and examples on this feature are available at http://www.ftdichip.com under FTDIChip-ID Projects. The TTL-232RG generic cables require USB drivers, available free from http://www.ftdichip.com, which are used to make the FT232R in the cable appear as a virtual COM port (VCP). This then allows the user to communicate with the USB interface via a standard PC serial emulation port (for example TTY). Another FTDI USB driver, the D2XX driver, can also be used with application software to directly access the FT232R on the cable though a DLL. This is illustrated in the Figure 1.1 Figure 1.1 - Using the TTL-232RG Generic Cable Copyright © Future Technology Devices International Limited 2 TTL to USB Serial Converter Generic Cables Datasheet Version 1.5 Document Reference No.: FT_000188 Clearance No.: FTDI# 129 1.1 Available Cables and Part Numbers The following Table 1.1 gives details of the available TTL-232RG generic cables. Part Number Description End Connector* Cable details USB to UART cable with +3.3V TTL-232RG- TTL level UART signals. Maximum Wire Ended (no 6 core, UL2464 24 AWG, VSW3V3-WE output of 50mA on VCC connector) diam=5mm (see Note 1 and Note 4) USB to UART cable with +3.3V TTL-232RG- TTL level UART signals. Maximum Wire Ended (no 6 core, UL2464 24 AWG, VREG3V3-WE output of 250mA on VCC connector) diam=5mm (see Note 2 and 5) USB to UART cable with +1.8V TTL-232RG- TTL level UART signals. Maximum Wire Ended (no 6 core, UL2464 24 AWG, VREG1V8-WE output of 100mA on VCC connector) diam=5mm (see Note 2 and 6) USB to UART cable with up to 5V TTL-232RG- TTL level UART signals. Maximum Wire Ended (no 6 core, UL2464 24 AWG, VSW5V-WE output of 450mA on VCC connector) diam=5mm Wire Ended (no 6 core, UL2464 24 AWG, connector) diam=5mm (see Note 7) USB to UART cable with TTL Voltage levels for the UART TTL-232RGVIP-WE signals are supplied from the customers interface logic (see Note 3 and 8) Table 1.1 TTL-232RG Generic Cables Descriptions and Part Numbers Note 1: Fixed 3.3V signals and supply. Note 2: Any regulator from 1.8V to 5V can be used. 1.8V and 3.3V versions are standard products. Others values are customized at the factory. Note 3: Any INPUT voltage can be supplied by the customer from 1.8V (min value of VCCIO) to +5.25V (Max value of VCCIO) Note 4: The VCC power output signal (RED wire) is 3.3V. The source of 3.3V is the FT232R regulator output, which is switched onto the power output signal. Note 5: The VCC power output signal (RED wire) is 3.3V. The source of 3.3V is on board 3.3V regulator output, which is switched onto the power output signal Note 6: The VCC power output signal (RED wire) is 1.8V. The source of 1.8V is on board 1.8V regulator output, which is switched onto the power output signal Copyright © Future Technology Devices International Limited 3 TTL to USB Serial Converter Generic Cables Datasheet Version 1.5 Document Reference No.: FT_000188 Clearance No.: FTDI# 129 Note 7: The VCC power output signal (RED wire) is 5.0V. The source of 5.0V is the USB VBUS input, which is switched onto the power output signal. At the time of releasing these cables, this cable was not available. It will become available at a later date. Please contact FTDI Sales for further information. Note 8: The VCC power input signal (RED wire) is an output from customer electronics, an input to the cable. This value=i/pV. The source of i/pV is from customer’s interface logic and this is used to drive the VCCIO and hence the signal levels on the wires. This makes the generic cable customisable to whatever output voltage the customer interface is operating at 1.8V to 5.25V range. FTDI supports customised end connector designs. For more information, please contact your local FTDI sales office (see end of datasheet for contact details). 1.2 Certifications The FTDI TTL-232RG range of generic cables is fully RoHS compliant and FCC/CE approved. Copyright © Future Technology Devices International Limited 4 TTL to USB Serial Converter Generic Cables Datasheet Version 1.5 Document Reference No.: FT_000188 Clearance No.: FTDI# 129 Table of Contents 1 2 Introduction .................................................................... 2 1.1 Available Cables and Part Numbers........................................... 3 1.2 Certifications ............................................................................ 4 Typical Applications ........................................................ 6 2.1 Driver Support .......................................................................... 6 2.2 Features .................................................................................... 7 3 FT232R features applicable to TTL-232RG generic cables 8 4 TTL-232RG generic cable connection/mechanical details 9 4.1 TTL-232RG Generic Cables Signal Descriptions ......................... 9 4.2 TTL-232RG Generic Cables Electrical Parameters .................... 10 4.2.1 TTL-232RG-VSW3V3-WE Electrical Parameters ............................................ 10 4.2.2 TTL-232RG-VREG3V3-WE Electrical Parameters........................................... 10 4.2.3 TTL-232RG-VREG1V8-WE Electrical Parameters........................................... 11 4.2.4 TTL-232RG-VSW5V-WE Electrical Parameters ............................................. 11 4.2.5 TTL-232RG-VIP-WE Electrical Parameters ................................................... 12 5 Cable PCB Circuit Schematic .......................................... 13 6 Contact Information ...................................................... 14 Appendix A - Cable EEPROM Configuration......................... 16 Appendix B - References .................................................... 18 Document References ..................................................................... 18 Acronyms and Abbreviations ........................................................... 18 Appendix C - List of Figures and Tables ............................. 19 List of Figures ................................................................................. 19 List of Tables ................................................................................... 19 Appendix C – Revision History ........................................... 20 Copyright © Future Technology Devices International Limited 5 TTL to USB Serial Converter Generic Cables Datasheet Version 1.5 Document Reference No.: FT_000188 Clearance No.: FTDI# 129 2 Typical Applications  USB to Serial TTL Level Converter  Upgrading Legacy Peripherals to USB  Interface Microcontroller UART or I/O to USB  Interface FPGA / PLD to USB  Interface to FTDI VDRIVE2 or VMUSIC2 modules.  Interface USB to none-standard (application dependant) logic levels.  Replace MAX232 type level shifters allowing for direct connection of products to PC via USB  USB Instrumentation PC interface  USB Industrial Control  USB Software / Hardware Encryption Dongles 2.1 Driver Support Royalty free VIRTUAL COM PORT Royalty free D2XX Direct Drivers (VCP) DRIVERS for... (USB Drivers + DLL S/W Interface)  Windows 10 32,64-bit  Windows 10 32,64-bit  Windows 8/8.1 32,64-bit  Windows 8/8.1 32,64-bit  Windows 7 32,64-bit  Windows 7 32,64-bit  Windows Vista and Vista 64-bit  Windows Vista and Vista 64-bit  Windows XP and XP 64-bit  Windows XP and XP 64-bit  Windows 98, 98SE, ME, 2000, Server 2003, XP, Server 2008 and server 2012 R2  Windows 98, 98SE, ME, 2000, Server 2003, XP, Server 2008 and server 2012 R2  Windows XP Embedded  Windows XP Embedded  Windows CE 4.2, 5.0 and 6.0  Windows CE 4.2, 5.0 and 6.0  Mac OS 8/9, OS-X  Linux 2.4 and greater  Linux 2.4 and greater  Android (J2xx) The drivers listed above are all available to download for free from http://www.ftdichip.com. Various 3rd Party Drivers are also available for various other operating systems - see http://www.ftdichip.com for details. Copyright © Future Technology Devices International Limited 6 TTL to USB Serial Converter Generic Cables Datasheet Version 1.5 Document Reference No.: FT_000188 Clearance No.: FTDI# 129 2.2 Features  TTL-232RG generic converter cable provides a USB to TTL Serial interface with various logic levels.  On board FT232RQ provides single chip USB to asynchronous serial data transfer interface.  Entire USB protocol handled by the electronics in the cable USB.     Support for FT232R FTDIChip-ID™ feature for improved security.  Voltage output power allows external logic to be powered from the USB port.  Cable can be used to accept IO voltage from application interface logic allowing users to supply IO voltage levels. Connect directly to a microcontroller UART or I/O pins.  6 way outputs provide Tx, Rx, RTS#, CTS#, VCC and GND. UART interface support for 7 or 8 data bits, 1 or 2 stop bits and odd / even / mark / space / no parity.  Low USB bandwidth consumption.  UHCI / OHCI / EHCI host controller compatible.  USB 2.0 (12Mb/s) Full Speed compatible.  -40°C to +85°C operating temperature range.  Cable length is 1.80m (6 feet).  FCC and CE compliant.  Custom versions also available (subject to MOQ). Fully assisted hardware (RTS#/CTS#) or X-On / X-Off software handshaking.  Data transfer rates from 300 baud to 3 Mbaud at TTL levels.  Internal EEPROM with user writeable area.  Wide range of output drive voltages 1.8V to 5.0V safe TTL inputs makes the TTL-232RG easy to interface to 5.0V MCU’s.  FTDI’s royalty-free VCP allow for communication as a standard emulated COM port and D2XX ‘direct’ drivers provide DLL application programming interface. Copyright © Future Technology Devices International Limited 7 TTL to USB Serial Converter Generic Cables Datasheet Version 1.5 Document Reference No.: FT_000188 Clearance No.: FTDI# 129 3 FT232R features applicable to TTL-232RG generic cables The TTL-232RG generic cables use FTDI’s FT232RQ USB to serial IC device. This section summarises the key features of the FT232RQ which apply to the TTL-232RG USB to serial TTL converter cables. For further details, and a full features and enhancements description consult the FT232R datasheet, this is available from http://www.ftdichip.com. Internal EEPROM. The internal EEPROM in each cable is used to store USB Vendor ID (VID), Product ID (PID), device serial number, product description string and various other USB configuration descriptors. Each cable is supplied with the internal EEPROM pre-programmed as described in Appendix AError! Reference source not found.. A user area of the internal EEPROM is available to system designers to allow storing additional data. The internal EEPROM descriptors can be programmed in circuit, over USB without any additional voltage requirement. It can be programmed using the FTDI utility software called MPROG, which can be downloaded from FTDI Utilities on the FTDI website (www.ftdichip.com). Lower Operating and Suspend Current. The FT232R has a low 15mA operating supply current and a very low USB suspend current of approximately 70μA. (Note that during suspend mode, the current drawn by application should not exceed 2.5mA to remain USB compliant) Low USB Bandwidth Consumption. The USB interface of the FT232R, and therefore the TTL-232RG cables has been designed to use as little as possible of the total USB bandwidth available from the USB host controller. High Output Drive Option. The UART interface I/O pins on the TTL-232RG cables (RXD, TXD, RTS#, and CTS#) can be configured to use the FT232R’s high output drive option. This option allows the FT232R I/O pins to drive up to three times the standard signal drive level. This allows multiple devices to be driven, or devices that require greater signal drive strength to be interfaced to the cables. This option is enabled in the internal EEPROM. UART Pin Signal Inversion. The sense of each of the eight UART signals can be individually inverted by configuring options in the internal EEPROM. For example CTS# (active low) can be changed to CTS (active high), or TXD can be changed to TXD#. FTDIChip-ID™. The FT232R includes the FTDIChip-ID™ security dongle feature. This FTDIChip-ID™ feature allows a unique number to be burnt into each cable during manufacture. This number cannot be reprogrammed. This number is only readable over USB can be used to form the basis of a security dongle which can be used to protect any customer application software being copied. This allows the possibility of using the TTL-232RG cables as a dongle for software licensing. Further to this, a renewable license scheme can be implemented based on the FTDIChip-ID™ number when encrypted with other information. This encrypted number can be stored in the user area of the FT232R internal EEPROM, and can be decrypted, then compared with the protected FTDIChip-ID™ to verify that a license is valid. Web based applications can be used to maintain product licensing this way. An application note, AN232R-02, available from FTDI website (www.ftdichip.com) describes this feature. Improved EMI Performance. The TTL-232RG cables are FCC and CE certified. Extended Operating Temperature Range - The TTL-232RG generic cables are capable of operating over an extended temperature range of -40º to +85º C thus allowing them to be used in automotive or industrial applications. Copyright © Future Technology Devices International Limited 8 TTL to USB Serial Converter Generic Cables Datasheet Version 1.5 Document Reference No.: FT_000188 Clearance No.: FTDI# 129 4 TTL-232RG generic cable connection/mechanical details The following Figure 4.1 shows the cable signals and the wire colours for these signals on the TTL-232RG generic cables. Figure 4.1 TTL-232RG Generic Cables Connections (numbers refer to pad numbers on the PCB) Figure 4.2 TTL-232RG Generic Cables Mechanical Details (dimensions in mm) 4.1 TTL-232RG Generic Cables Signal Descriptions Colour Name Type Description Black GND GND Device ground supply pin. Brown CTS# Input Clear to Send Control input / Handshake signal. Red VCC Output or input Orange TXD Output Yellow RXD Input Green RTS# Output Power Supply Output except for the TTL-232RG-VIPWE were this is an input and power is supplied by the application interface logic. Transmit Asynchronous Data output. Receive Asynchronous Data input. Request To Send Control Output / Handshake signal. Table 4.1 TTL-232RG Generic Cables Signal Descriptions Copyright © Future Technology Devices International Limited 9 TTL to USB Serial Converter Generic Cables Datasheet Version 1.5 Document Reference No.: FT_000188 Clearance No.: FTDI# 129 4.2 TTL-232RG Generic Cables Electrical Parameters 4.2.1 TTL-232RG-VSW3V3-WE Electrical Parameters Parameter VCC IO T Description Minimum Typical Maximum Units 3.2 3.3 3.4 V - 50 - mA +85 oC Output Power Voltage Output Power Current Operating -40 Temperature Range Conditions Must be less than 2.5mA during suspend. Table 4.2 TTL-232RG-VSW3V3-WE I/O Operating Parameters Parameter Description Minimum Typical Maximum Units Conditions Voh Output Voltage High 2.2 2.8 3.2 V I source = 1mA Vol Output Voltage Low 0.3 0.4 0.6 V I sink = 2mA Vin Input Switching Threshold 1.0 1.2 1.5 V VHys Input Switching Hysteresis 20 25 30 mV Table 4.3 TTL-232RG-VSW3V3-WE I/O Pin Characteristics 4.2.2 TTL-232RG-VREG3V3-WE Electrical Parameters Parameter VCC IO T Description Minimum Typical Maximum Units 3.2 3.3 3.4 V Output Power Voltage Output Power 250 Current Operating Temperature Range Conditions Must be less than 2.5mA mA -40 +85 during suspend. oC Table 4.4 TTL-232RG-VREG3V3-WE I/O Operating Parameters Parameter Description Minimum Typical Maximum Units Conditions Voh Output Voltage High 2.2 2.8 3.2 V I source = 3mA Vol Output Voltage Low 0.3 0.4 0.6 V I sink = 8mA Vin Input Switching Threshold 1.0 1.2 1.5 V VHys Input Switching Hysteresis 20 25 30 mV Table 4.5 TTL-232RG-VREG3V3 Pin Characteristics Copyright © Future Technology Devices International Limited 10 TTL to USB Serial Converter Generic Cables Datasheet Version 1.5 Document Reference No.: FT_000188 Clearance No.: FTDI# 129 4.2.3 TTL-232RG-VREG1V8-WE Electrical Parameters Parameter VCC IO T Description Minimum Typical Maximum Units 1.32 1.62 1.8 V Output Power Voltage Output Power 100 Current Operating 100mA for output mA -40 Temperature Range Conditions +85 powerless than 3.0V oC Table 4.6 TTL-232RG-VREG1V8 I/O Operating Parameters Parameter Description Minimum Typical Maximum Units Conditions Voh Output Voltage High 1.32 1.62 1.8 V I source = 6mA Vol Output Voltage Low 0.06 0.1 0.18 V I sink = 6mA Vin Input Switching Threshold 1.0 1.2 1.5 V VHys Input Switching Hysteresis 20 25 30 mV Table 4.7 TTL-232RG-VREG1V8-WE I/O Pin Characteristics 4.2.4 TTL-232RG-VSW5V-WE Electrical Parameters Parameter VCC IO T Description Output Power Voltage Minimum Typical Maximum Units 4.25 5.0 5.25 V - 450 Supply Current Operating Temperature Range mA -40 +85 Conditions Must be less than 2.5mA during suspend. oC Table 4.8 TTL-232RG-VSW5V-WE I/O Operating Parameters Parameter Description Minimum Typical Maximum Units Conditions Voh Output Voltage High 3.2 4.1 4.9 V I source = 6mA Vol Output Voltage Low 0.3 0.4 0.6 V I sink = 6mA Vin Input Switching Threshold 1.0 1.2 1.5 V VHys Input Switching Hysteresis 20 25 30 mV Table 4.9 TTL-232RG-VSW5V-WE I/O Pin Characteristics Copyright © Future Technology Devices International Limited 11 TTL to USB Serial Converter Generic Cables Datasheet Version 1.5 Document Reference No.: FT_000188 Clearance No.: FTDI# 129 4.2.5 TTL-232RG-VIP-WE Electrical Parameters Parameter VCC IO T Description Minimum Power Input for I/O Supply Current Temperature Range Maximum Units 5.25 V * mA +85 oC INPUT 1.8 Buffer Operating Typical i/p * * -40 Conditions Must be less than 2.5mA during suspend. Table 4.10 TTL-232RG-VIP-WE I/O Operating Parameters Parameter Description Minimum Typical Maximum Units Conditions Voh Output Voltage High * * * V I source = 6mA Vol Output Voltage Low * * * V I sink = 6mA Vin Input Switching Threshold * * * V VHys Input Switching Hysteresis * * * mV Table 4.11 TTL-232RG-VIP-WE I/O Pin Characteristics *depends on supplied voltage Copyright © Future Technology Devices International Limited 12 TTL to USB Serial Converter Generic Cables Datasheet Version 1.5 Document Reference No.: FT_000188 Clearance No.: FTDI# 129 5 Cable PCB Circuit Schematic The circuit schematic for the small internal electronic circuit board, utilising the FTDI FT232R, which is encapsulated into the USB connector end of the cable, is shown in Figure 5.1. Customised versions of these cables are also available. Users interested in customised versions of these cables should contact FTDI sales (sales1@ftdichip.com). Figure 5.1 Circuit Schematic of PCB Used in the generic TTL to USB Serial Converter Cables Copyright © Future Technology Devices International Limited 13 TTL to USB Serial Converter Generic Cables Datasheet Version 1.5 Document Reference No.: FT_000188 Clearance No.: FTDI# 129 6 Contact Information Head Office – Glasgow, UK Branch Office – Tigard, Oregon, USA Future Technology Devices International Limited Unit 1, 2 Seaward Place, Centurion Business Park Glasgow, G41 1HH United Kingdom Tel: +44 (0) 141 429 2777 Fax: +44 (0) 141 429 2758 Future Technology Devices International Limited (USA) 7130 SW Fir Loop Tigard, OR 97223-8160 USA Tel: +1 (503) 547 0988 Fax: +1 (503) 547 0987 E-mail (Sales) E-mail (Support) E-mail (General Enquiries) Web Shop URL sales1@ftdichip.com support1@ftdichip.com admin1@ftdichip.com http://www.ftdichip.com E-Mail (Sales) E-mail (Support) E-mail (General Enquiries) us.sales@ftdichip.com us.support@ftdichip.com us.admin@ftdichip.com Branch Office – ShangHai, China Branch Office – Taipei, Taiwan Future Technology Devices International Limited (Taiwan) 2F, No. 516, Sec. 1, NeiHu Road Taipei 114 Taiwan, R.O.C. Tel: +886 (0) 2 8797 1330 Fax: +886 (0) 2 8751 9737 E-mail (Sales) E-mail (Support) E-mail (General Enquiries) tw.sales1@ftdichip.com tw.support1@ftdichip.com tw.admin1@ftdichip.com Future Technology Devices International Limited (China) Room 1103, No. 666 West Huaihai Road, Shanghai, 200052 China Tel: +86 (21) 62351596 Fax: +86 (21) 62351595 E-Mail (Sales) cn.sales@ftdichip.com E-mail (Support) cn.support@ftdichip.com E-Mail (General Enquiries) cn.admin@ftdichip.com Web Site URL: http://www.ftdichip.com Distributor and Sales Representatives Please visit the Sales Network page of the FTDI Web site for the contact details of our distributor(s) and sales representative(s) in your country. System and equipment manufacturers and designers are responsible to ensure that their systems, and any Future Technology Devices International Ltd (FTDI) devices incorporated in their systems, meet all applicable safety, regulatory and system-level performance requirements. All application-related information in this document (including application descriptions, suggested FTDI devices and other materials) is provided for reference only. While FTDI has taken care to assure it is accurate, this information is subject to customer confirmation, and FTDI disclaims all liability for system designs and for any applications assistance provided by FTDI. Use of FTDI devices in life support and/or safety applications is entirely at the user’s risk, and the user agrees to defend, indemnify a nd hold harmless FTDI from any and all damages, claims, suits or expense resulting from such use. This document is subject to change without notice. No freedom to use patents or other intellectual property rights is implied by the publication of this document. Neith er the whole nor any part of the information contained in, or the product described in this document, may be adapted or reproduced in any material or electronic form without the prior written consent of the copyright holder. Future Technology Devices International Ltd, Un it 1, 2 Seaward Place, Centurion Business Park, Glasgow G41 1HH, United Kingdom. Scotland Registered Company Number: SC136640 Copyright © Future Technology Devices International Limited 14 TTL to USB Serial Converter Generic Cables Datasheet Version 1.5 Document Reference No.: FT_000188 Clearance No.: FTDI# 129 Appendix A - Cable EEPROM Configuration Each TTL-232RG cable is controlled by the FTDI FT232R IC. This FT232R device contains an EEPROM which contains the USB configuration descriptors for that device. When the cable is plugged into a PC or a USB reset is performed, the PC will read these descriptors. The default values stored into the internal EEPROM are defined in the following table. Parameter Value USB Vendor ID (VID) 0403h FTDI default VID (hex) USB Product UD (PID) 6001h FTDI default PID (hex) Serial Number Enabled? Notes Yes A unique serial number is generated and programmed into the Serial Number Pull down I/O Pins in USB Suspend Manufacturer Name See Note EEPROM during device final test. Enabling this option will make the device pull down on the UART Disabled interface lines when the power is shut off (PWREN# is high). FTDI Product description depends on the cable. The following lists a few of the Product description for each different cable. TTL-232RG-VSW3V3 Product Description See note TTL-232RG-VREG3V3 TTL-232RG-VREG1V8 TTL-232RG-VREGxVx TTL-232RG-VIP Max Bus Power Current Power Source 90mA Bus Powered Device Type FT232R USB Version 0200 Returns USB 2.0 device description to the host. Note: The device is a USB 2.0 Full Speed device (12Mb/s). Remote Wake Up Disabled 500uA suspend limit when in this state High Current I/Os Enabled Enables the high drive level on the UART and CBUS I/O pins. Load VCP Driver Enabled Makes the device load the VCP driver interface for the device. Invert TXD Disabled Signal on this pin becomes TXD# if enable. Invert RXD Disabled Signal on this pin becomes RXD# if enable. Copyright © Future Technology Devices International Limited 16 TTL to USB Serial Converter Generic Cables Datasheet Version 1.5 Document Reference No.: FT_000188 Parameter Value Invert RTS# Disabled Signal on this pin becomes RTS if enable. Invert CTS# Disabled Signal on this pin becomes CTS if enable. Clearance No.: FTDI# 129 Notes Copyright © Future Technology Devices International Limited 17 TTL to USB Serial Converter Generic Cables Datasheet Version 1.5 Document Reference No.: FT_000188 Clearance No.: FTDI# 129 Appendix B - References Document References NA Acronyms and Abbreviations Terms DLL EEPROM Description Dynamic Link Library Electrically Erasable Programmable Read Only Memory EHCI Enhanced Host Controller Interface FCC Federal Communications Commission FPGA I/O OHCI PC Field Programmable Gate Array Input Output Open Host Controller Interface Personal Computer PLD Programmable Logic Device TTL Transistor-Transistor Logic UART Universal Asynchronous Receiver Transmitter UHCI Universal Host Controller Interface USB Universal Serial Bus VCP Virtual COM Port Copyright © Future Technology Devices International Limited 18 TTL to USB Serial Converter Generic Cables Datasheet Version 1.5 Document Reference No.: FT_000188 Clearance No.: FTDI# 129 Appendix C - List of Figures and Tables List of Figures Figure 1.1 - Using the TTL-232RG Generic Cable .............................................................................. 2 Figure 4.1 TTL-232RG Generic Cables Connections (numbers refer to pad numbers on the PCB) ............. 9 Figure 4.2 TTL-232RG Generic Cables Mechanical Details (dimensions in mm) ...................................... 9 Figure 5.1 Circuit Schematic of PCB Used in the generic TTL to USB Serial Converter Cables ................ 13 List of Tables Table 1.1 TTL-232RG Generic Cables Descriptions and Part Numbers .................................................. 3 Table 4.1 TTL-232RG Generic Cables Signal Descriptions ................................................................... 9 Table 4.2 TTL-232RG-VSW3V3-WE I/O Operating Parameters .......................................................... 10 Table 4.3 TTL-232RG-VSW3V3-WE I/O Pin Characteristics ............................................................... 10 Table 4.4 TTL-232RG-VREG3V3-WE I/O Operating Parameters ......................................................... 10 Table 4.5 TTL-232RG-VREG3V3 Pin Characteristics ......................................................................... 10 Table 4.6 TTL-232RG-VREG1V8 I/O Operating Parameters ............................................................... 11 Table 4.7 TTL-232RG-VREG1V8-WE I/O Pin Characteristics .............................................................. 11 Table 4.8 TTL-232RG-VSW5V-WE I/O Operating Parameters ............................................................ 11 Table 4.9 TTL-232RG-VSW5V-WE I/O Pin Characteristics ................................................................. 11 Table 4.10 TTL-232RG-VIP-WE I/O Operating Parameters ................................................................ 12 Table 4.11 TTL-232RG-VIP-WE I/O Pin Characteristics..................................................................... 12 Copyright © Future Technology Devices International Limited 19 TTL to USB Serial Converter Generic Cables Datasheet Version 1.5 Document Reference No.: FT_000188 Clearance No.: FTDI# 129 Appendix C – Revision History Document Title: TTL-232RG Datasheet Document Reference No.: FT_000188 Clearance No.: FTDI# 129 Product Page: http://www.ftdichip.com/FTProducts.htm Document Feedback: Send Feedback Revision Changes Date Version 1.0 Initial Release 2009-11-17 Version 1.1 Updated release 2010-04-02 Version 1.2 A note added about the availability of the TTL_232RG-VSW5V-WE at the time of launch; Updated FCC/CE testing and approval status 2010-15-21 Version 1.3 Updated parametric value tables; update contact details; updated list of drivers supported 2015-08-11 Version 1.4 Changed the tolerance of wire length in 4.2 2016-05-23 Version 1.5 Updated table 4.2 and table 4.4 2018-05-04 Copyright © Future Technology Devices International Limited 20