UMFT234XD-01

UMFT234XD Datasheet Version 1.1 Document Reference No.: FT_000801 Clearance No.: FTDI# Future Technology Devices International Datasheet UMFT234XD Breakout Modules UMFT234XD is a USB to UART breakout module 1 Introduction The UMFT234XD breakout module utilizes FTDI’s FT234XD IC to convert USB to UART. 1.1 Features The UMFT234XD is a breakout board that converts USB2.0 Full-Speed to UART. These modules do not have a USB connector, instead, the modules plug directly into the USB host connector and the pads of the PCB makes electrical contact with the electrical contacts of the USB connector. The UART interface operates at +3.3V voltage levels, however all I/Os are 5V tolerant. 1.2 Ordering Information Module Interface Features UMFT234XD-01 UART USB to UART with four control bus lines, 3.3V power out limited to 50mA and 5V with as safety fuse. UART signals available via 8 pin female connector. UMFT234XD-NC UART USB to UART with four control bus lines, 3.3V power out limited to 50mA and 5V with as safety fuse. UART signals available via 8 pads on the PCB. UMFT234XD-WE UART USB to UART with four control bus lines, 3.3V power out limited to 50mA and 5V with as safety fuse. UART signals available via 8, 6” flying leads connected to the PCB pads. 2 Driver Support Royalty-Free VIRTUAL COM PORT (VCP): Royalty-Free D2XX Direct Drivers:  Windows 8 32,64-bit  Windows 8 32,64-bit  Windows 7 32,64-bit  Windows 7 32,64-bit  Windows Vista  Windows Vista  Windows XP 32,64-bit  Windows XP 32,64-bit  Windows XP Embedded  Windows XP Embedded  Windows CE.NET 4.2 , 5.0 and 6.0  Windows CE.NET 4.2, 5.0 and 6.0  MAC OS OS-X  MAC OS OS-X  Linux 3.0 and greater  Linux 3.0 and greater  Android  Android The drivers listed above are all available to download for free from www.ftdichip.com. Various 3rd Party Drivers are also available for various other operating systems - visit www.ftdichip.com for details. Use of FTDI devices in life support and/or safety applications is entirely at the user’s risk, and the user agrees to defend, indemnify and hold harmless FTDI from any and all damages, claims, suits or expense resulting from such use. 327 UMFT234XD Datasheet Version 1.1 Document Reference No.: FT_000801 Clearance No.: FTDI# 327 Table of Contents 1 Introduction ................................................................................... 1 1.1 Features ........................................................................................................ 1 1.2 Ordering Information .................................................................................... 1 2 Driver Support ................................................................................ 1 3 UMFT234XD Signals and Configurations ......................................... 3 3.1 UMFT234XD CN1 Signal Descriptions ............................................................ 3 3.2 UMFT234XD CN2 Signal Descriptions ............................................................ 3 3.3 CBUS Signal Options ..................................................................................... 4 3.4 Configuring the MTP ROM .............................................................................. 5 4 Module Dimensions ........................................................................ 5 5 Module Wire Connections ............................................................... 6 6 5.1 UMFT234XD-WE Wire Connections ................................................................ 6 5.2 UMFT234XD-WE ............................................................................................ 6 Module Circuit Schematic ............................................................... 7 6.1 UMFT234XD Schematic ................................................................................. 7 7 Environmental Compliances ........................................................... 7 8 Internal MTP ROM Configuration .................................................... 8 9 Contact Information ....................................................................... 9 Appendix A - List of Figures and Tables................................................................... 9 Appendix B: Revision History ................................................................................ 10 2 Copyright © 2015 Future Technology Devices International Limited UMFT234XD Datasheet Version 1.1 Document Reference No.: FT_000801 Clearance No.: FTDI# 327 UMFT234XD Signals and Configurations 3 CN1 connects directly to a USB host or HUB port, or can be connected to a USB extension cable. This connects to USB signals, 5V USB Bus power and GND. When connecting the module to a USB host or HUB the signal pads should be facing upwards when connecting to a horizontal connector and be facing right for vertical connectors. If the module is plugged in upside down no connectivity will be made between PCB and HUB, no damage will occur from plugging the module in the wrong way. 3.1 UMFT234XD CN1 Signal Descriptions Pin No. Name Type Description PWR 5V Power input USB port. For a low power USB bus powered design, up to 100mA can be sourced from the 5V supply on the USB bus. A maximum of 500mA can be sourced from the USB bus in a high power USB bus powered design. 1 VBUS 2 D- Signal Negative USB data signal 3 D+ Signal Positive USB data signal 4 GND PWR Module Ground Table 3.1 USB Connector Pin Out Description 3.2 UMFT234XD CN2 Signal Descriptions Pin No. Name Type Description 1 TXD Output UART transmit data 2 VBUS PWR Output 5V Power output USB port. 3 GND PWR Module Ground Supply 4 RESET# Input Can be used by an external device to reset the FT234XD. 5 RXD Input UART receive data 6 3V3 Output 7 RTS# Output 3.3V output from FT234XD integrated LDO regulator. This pin is decoupled to ground on the module PCB with a 10nF capacitor and offers 3V3 at up to 50mA for external hardware. UART Ready to Send handshake signal 8 GND PWR Module Ground Supply 9 CTS# Input 10 CB0 I/O UART Clear to Send handshake signal Configurable CBUS0 I/O Pin. The function of this pin is configured in the device internal MTP ROM. See Table 3.3 Table 3.2 UART Module Pin Out Description 3 Copyright © 2015 Future Technology Devices International Limited UMFT234XD Datasheet Version 1.1 Document Reference No.: FT_000801 Clearance No.: FTDI# 327 3.3 CBUS Signal Options CBUS Signal Option Available On CBUS Pin Description Tristate CBUS0 IO Pad is tri-stated DRIVE_1 CBUS0 Output a constant 1 DRIVE_0 CBUS0 Output a constant 0 TXDEN CBUS0 Enable transmit data for RS485 PWREN# CBUS0 Output is low after the device has been configured by USB, then high during USB suspend mode. This output can be used to control power to external logic. TXLED# CBUS0 Transmit data LED drive – open drain pulses low when transmitting data via UART. RXLED# CBUS0 Receive data LED drive – open drain pulses low when receiving data via UART. TX&RXLED# CBUS0 LED drive – open drain pulses low when transmitting or receiving data via UART. SLEEP# CBUS0 Goes low during USB suspend mode. Typically used to power down external logic to RS232 level converter IC in USB to RS232 converter designs CLK24MHz CBUS0 24 MHz Clock output.** CLK12MHz CBUS0 12 MHz Clock output.** CLK6MHz CBUS0 6 MHz Clock output.** GPIO CBUS0 CBUS bit bang mode option. Allows up to 4 of the CBUS pins to be used as general purpose I/O. A separate application note, AN232R-01, available from FTDI website (www.ftdichip.com) describes in more detail how to use CBUS bit bang mode. BCD_Charger CBUS0 Battery Charge Detect indicates when the device is connected to a dedicated battery charger host. Active high output. NOTE: Requires a 10K pull-down to remove power up toggling. BCD_Charger# CBUS0 Active low BCD Charger, driven by an open drain to ground with no internal pull-up. BitBang_WR# CBUS0 Synchronous and asynchronous bit bang mode WR# strobe output. BitBang_RD# CBUS0 Synchronous and asynchronous bit bang mode RD# strobe output. VBUS_Sense CBUS0 Input to detect when VBUS is present. Time_Stamp CBUS0 Toggle signal which changes state each time a USB SOF is received Keep_Awake# CBUS0 Active Low input, prevents the chip from going into suspend. Table 3.3 CBUS Configuration Control * PWREN# must be used with a 10kΩ resistor pull up. **When in USB suspend mode the outputs clocks are also suspended. 4 Copyright © 2015 Future Technology Devices International Limited UMFT234XD Datasheet Version 1.1 Document Reference No.: FT_000801 Clearance No.: FTDI# 327 3.4 Configuring the MTP ROM The FT234XD IC on the module contains an embedded MTP ROM, this can be used to specify the functions of the CBUS0 pin, the current drive on each signal pin, current limit for the USB bus and the descriptors of the device. These features can be programmed using FTDI’s programming utility FT_Prog. For details on using FT_Prog, please see the FT_PROG User Guide. When programming the MTP ROM please note: i) The Max Bus Power setting of the MTP ROM should specify the maximum current to be drawn from the USB host/hub when enumerated. For high-powered USB devices the current limit when enumerated is between 100mA and 500mA, for low-powered USB devices the current limit is 100mA. 4 Module Dimensions 14.9 2.4 2.54 12.10 36.3 15.5 14.1 44.5 2.00 Measurements given in millimetres Tolerance +/-0.1mm Figure 4.1 UMFT234XD-01 Module Dimensions 5 Copyright © 2015 Future Technology Devices International Limited UMFT234XD Datasheet Version 1.1 Document Reference No.: FT_000801 5 Clearance No.: FTDI# Module Wire Connections 5.1 UMFT234XD-WE Wire Connections VBUS TXD 2 2 1 1 RXD 5 5 RTS# 7 7 CTS# 9 9 Wire 6" GND 8 8 CB0 10 10 4 4 RESET# 3v3 GND 6 6 3 3 RED ORANGE YELLOW GREEN BROWN GREY PURPLE WHITE BLUE BLACK Figure 5.1 UMFT234XD-WE Wire Connections (numbers refer to pad numbers on the PCB) Figure 5.1 illustrates the –WE product as a cable. This is only for illustration purposes. The wire ended product consists of individual wires – not a cable 5.2 UMFT234XD-WE Figure 5.2 UMFT234XD-WE Image 6 Copyright © 2015 Future Technology Devices International Limited 327 UMFT234XD Datasheet Version 1.1 Document Reference No.: FT_000801 6 Clearance No.: FTDI# Module Circuit Schematic 6.1 UMFT234XD Schematic Figure 6.1 UMFT234XD Circuit Schematic 7 Environmental Compliances The UMFT234XD modules exclusively use lead free components, and are fully compliant with European Union directive 2002/95/EC. 7 Copyright © 2015 Future Technology Devices International Limited 327 UMFT234XD Datasheet Version 1.1 Document Reference No.: FT_000801 8 Clearance No.: FTDI# 327 Internal MTP ROM Configuration Following a power-on reset or a USB reset the FT234XD will scan its internal MTP ROM and read the USB configuration descriptors stored there. The default values programmed into the internal MTP ROM in the FT234XD used on the UMFT234XD are shown in Table 8.1. Parameter Value Notes USB Vendor ID (VID) 0403h FTDI default VID (hex) USB Product UD (PID) 6015h FTDI default PID (hex) Serial Number Enabled? Yes Serial Number See Note A unique serial number is generated and programmed into the MTP ROM during final test of the UMFT234XD module. Pull down I/O Pins in USB Suspend Disabled Enabling this option will make the device pull down on the UART interface lines when the power is shut off (PWREN# is high). Manufacturer Name FTDI Product Description UMFT234XD Max Bus Power Current Power Source 90mA Bus Powered Device Type FT234XD USB Version 0200 Returns USB 2.0 device description to the host. Note: The device is a USB 2.0 Full Speed device (12Mb/s). Remote Wake Up Enabled Taking RI# low will wake up the USB host controller from suspend. High Current I/Os Disabled Enables the high drive level on the serial and CBUS I/O pins. Load VCP Driver Enabled Makes the device load the VCP driver interface for the device. CBUS0 PWREN# Table 8.1 Default Internal MTP ROM Configuration The internal MTP ROM in the FT234XD can be programmed over USB using the utility program FT_PROG. FT_PROG can be downloaded from www.ftdichip.com. Users who do not have their own USB vendor ID but who would like to use a unique Product ID in their design can apply to FTDI for a free block of unique PIDs. Contact FTDI Support (support1@ftdichip.com) for this service. 8 Copyright © 2015 Future Technology Devices International Limited UMFT234XD Datasheet Version 1.1 Document Reference No.: FT_000801 9 Clearance No.: FTDI# 327 Contact Information Head Office – Glasgow, UK Branch Office – Hillsboro, Oregon, USA Future Technology Devices International Limited Unit 1, 2 Seaward Place, Centurion Business Park Glasgow G41 1HH United Kingdom Tel: +44 (0) 141 429 2777 Fax: +44 (0) 141 429 2758 7130 SW Fir Loop Tigard, OR 97223-8160 USA Tel: +1 (503) 547 0988 Fax: +1 (503) 547 0987 E-mail (Sales) E-mail (Support) E-mail (General Enquiries) sales1@ftdichip.com support1@ftdichip.com admin1@ftdichip.com Branch Office – Taipei, Taiwan 2F, No. 516, Sec. 1, NeiHu Road Taipei 114 Taiwan , R.O.C. Tel: +886 (0) 2 8791 3570 Fax: +886 (0) 2 8791 3576 E-mail (Sales) E-mail (Support) E-mail (General Enquiries) tw.sales1@ftdichip.com tw.support1@ftdichip.com tw.admin1@ftdichip.com E-Mail (Sales) E-Mail (Support) E-Mail (General Enquiries) us.sales@ftdichip.com us.support@ftdichip.com us.admin@ftdichip.com Branch Office – Shanghai, China Room 1103, No. 666 West Huaihai Road, Shanghai, 200052 China Tel: +86 (0)21 6235 1596 Fax: +86 (0)21 6235 1595 E-mail (Sales) E-mail (Support) E-mail (General Enquiries) cn.sales@ftdichip.com cn.support@ftdichip.com cn.admin@ftdichip.com Web Site http://ftdichip.com Distributor and Sales Representatives Please visit the Sales Network page of the FTDI Web site for the contact details of our distributor(s) and sales representative(s) in your country. System and equipment manufacturers and designers are responsible to ensure that their systems, and any Future Technology Devices International Ltd (FTDI) devices incorporated in their systems, meet all applicable safety, regulatory and system-level performance requirements. All application-related information in this document (including application descriptions, suggested FTDI devices and other materials) is provided for reference only. While FTDI has taken care to assure it is accurate, this information is subject to customer confirmation, and FTDI disclaims all liability for system designs and for any applications assistance provided by FTDI. Use of FTDI devices in life support and/or safety applications is entirely at the user’s risk, and the user agrees to defend, indemnify and hold harmless FTDI from any and all damages, claims, suits or expense resulting from such use. This document is subject to change without notice. No freedom to use patents or other intellectual property rights is implied by the publication of this document. Neither the whole nor any part of the information contained in, or the product described in this document, may be adapted or reproduced in any material or electronic form without the prior written consent of the copyright holder. Future Technology Devices International Ltd, Unit 1, 2 Seaward Place, Centurion Business Park, Glasgow G41 1HH, United Kingdom. Scotland Registered Company Number: SC136640 9 Copyright © 2015 Future Technology Devices International Limited UMFT234XD Datasheet Version 1.1 Document Reference No.: FT_000801 Clearance No.: FTDI# 327 Appendix A - List of Figures and Tables List of Figures Figure 4.1 UMFT234XD-01 Module Dimensions ........................................................................................... 5 Figure 5.1 UMFT234XD-WE Wire Connections (numbers refer to pad numbers on the PCB) ................ 6 Figure 5.2 UMFT234XD-WE Image ................................................................................................................. 6 Figure 6.1 UMFT234XD Circuit Schematic .................................................................................................... 7 List of Tables Table 3.1 USB Connector Pin Out Description ............................................................................................. 3 Table 3.2 UART Module Pin Out Description ................................................................................................ 3 Table 3.3 CBUS Configuration Control .......................................................................................................... 4 Table 8.1 Default Internal MTP ROM Configuration ..................................................................................... 8 Copyright © 2013 Future Technology Devices International Limited 9 UMFT234XD Datasheet Version 1.1 Document Reference No.: FT_000801 Clearance No.: FTDI# Appendix B: Revision History Document Title: UMFT234XD Document Reference No.: FT_000801 Clearance No.: FTDI# 327 Product Page: http://www.ftdichip.com/FT-X.htm Document Feedback: Send Feedback Version 1.0 Initial Datasheet Created 31/01/13 Version 1.1 Corrected -01 part number 06/07/15 Copyright © 2013 Future Technology Devices International Limited 10 327