UMFT234XF

UMFT234XF Datasheet Version 1.0 Document Reference No.: FT_000818 Clearance No.: FTDI# 337 Future Technology Devices International Ltd Datasheet UMFT234XF Development Module UMFT234XF is a USB to UART development module 1 Introduction The UMFT234XF development module utilizes FTDI’s FT234XD IC to convert USB to a basic UART (RXD, TXD, RTS#, CTS#). 1.1 Features The UMFT234XF is a development module that converts USB2.0 Full-Speed to UART. The module includes a micro-B USB connector to connect to a USB host and the UART IO are available on separate pads. The module is designed to be soldered directly to another PCB (PCB on PCB technology). The UART interface operates between +1.8V and +3.3V voltage levels depending on the VIO signal, however all I/Os are 5V tolerant. An additional configurable bus (CBUS) pad allows for general IO or indicating that the module is connected to a dedicated charging port for battery charging. 1.2 Ordering Information Module Interface Features UMFT234XF UART USB 2.0 full speed to basic UART with one control bus line which may be used for battery charger detection. The PCB pads are designed to be soldered directly to another PCB for secure bonding. Use of FTDI devices in life support and/or safety applications is entirely at the user’s risk, and the user agrees to defend, indemnify and hold harmless FTDI from any and all damages, claims, suits or expense resulting from such use. UMFT234XF Datasheet Version 1.0 Document Reference No.: FT_000818 2 Clearance No.: FTDI# 337 Driver Support Royalty-Free VIRTUAL COM PORT (VCP): Royalty-Free D2XX Direct Drivers:  Windows 8 32,64-bit  Windows 8 32,64-bit  Windows 7 32,64-bit  Windows 7 32,64-bit  Windows Vista  Windows Vista  Windows XP 32,64-bit  Windows XP 32,64-bit  Windows XP Embedded  Windows XP Embedded  Windows CE.NET 4.2 , 5.0 and 6.0  Windows CE.NET 4.2, 5.0 and 6.0  MAC OS OS-X  MAC OS OS-X  Linux 3.0 and greater  Linux 3.0 and greater  Android  Android The drivers listed above as well as Third Party Drivers for other operating systems are available for free downloads from www.ftdichip.com. 2 Copyright © 2013 Future Technology Devices International Limited UMFT234XF Datasheet Version 1.0 Document Reference No.: FT_000818 Clearance No.: FTDI# 337 Table of Contents 1 Introduction ................................................................................... 1 1.1 Features ........................................................................................................ 1 1.2 Ordering Information .................................................................................... 1 2 Driver Support ................................................................................ 2 3 UMFT234XF Signals and Configurations.......................................... 4 4 3.1 UMFT234XF CN1 Signal Descriptions ............................................................. 4 3.2 UMFT234XF PAD Signal Descriptions ............................................................. 4 3.3 UMFT234XF J-1 ............................................................................................. 4 CBUS Signal Options ....................................................................... 5 4.1 Configuring the MTP ROM .............................................................................. 6 5 Module Dimensions ........................................................................ 7 6 Module Circuit Schematic ............................................................... 8 6.1 UMFT234XF Schematic .................................................................................. 8 7 Environmental Compliances ........................................................... 9 8 Internal MTP ROM Configuration .................................................. 10 9 Contact Information ..................................................................... 11 Appendix A - List of Figures and Tables ................................................................... 9 Appendix B: Revision History ................................................................................ 10 3 Copyright © 2013 Future Technology Devices International Limited UMFT234XF Datasheet Version 1.0 Document Reference No.: FT_000818 Clearance No.: FTDI# 337 UMFT234XF Signals and Configurations 3 USB connectivity is via CN1 a micro-B USB connector. The UART and CBUS signals are available on PCB pads. 3.1 UMFT234XF CN1 Signal Descriptions Pin No. Name Type Description 1 VBUS PWR 5V Power input to USB port, for a USB bus low-powered design; up to 100mA may be sourced from the 5V supply on the USB bus. A maximum of 500mA can be sourced from the USB bus in a USB bus high-powered design. 2 D- Signal Negative USB data signal 3 D+ Signal Positive USB data signal 4 ID Signal Not Connected 5 GND PWR Module Ground Table 1 USB Connector Pin Out Description 3.2 UMFT234XF PAD Signal Descriptions Pad Name Type P1 RESET# Signal P2 3V3 PWR P3 VIO PWR No. Description Active low input may be used to reset the FT234XD IC 3V3OUT from FT234XD. May be used for external logic. (50mA max) Also powers the FT234XD VCCIO (if JP1 fitted (default) Optional input to supply the FT234XD VCCIO from an external supply. VIO may be between 1.8V to 3.3V. JP1 must be disconnected to use this input. P4 GND PWR Module GND P5 VBUS PWR 5V output supplied from the USB port. P6 CB0 Signal Configurable Bus pin 0. Available settings for the pin are defined in table 3. The default is PWREN# P7 TXD Signal UART data output signal P8 RTS# Signal UART Ready to Send output signal. Active low. P9 RXD Signal UART data input signal P10 CTS# Signal UART Clear to Send input signal. Active low. Table 2 USB Connector Pin Out Description 3.3 UMFT234XF J-1 J-1 is used to connect/disconnect the 3V3OUT frm the FT234XD IC to the VCCIO input pin. By default it is connected. 4 Copyright © 2013 Future Technology Devices International Limited UMFT234XF Datasheet Version 1.0 Document Reference No.: FT_000818 4 Clearance No.: FTDI# 337 CBUS Signal Options CBUS Signal Option Available On CBUS Pin Tristate CBUS0 IO Pad is tri-stated DRIVE_1 CBUS0 Output a constant 1 DRIVE_0 CBUS0 Output a constant 0 TXDEN CBUS0 Enable transmit data for RS485 PWREN# CBUS0 Output is low after the device is configured by USB but high during USB suspended mode. This output is used to control power to external logic. TXLED# CBUS0 Transmit data LED drive – open drain pulses low when transmitting data via UART. RXLED# CBUS0 Receive data LED drive – open drain pulses low when receiving data via UART. TX&RXLED# CBUS0 LED drive – open drain pulses low when transmitting or receiving data via UART. SLEEP# CBUS0 Goes low during USB suspend mode. Typically used to power down external logic to RS232 level converter IC in USB to RS232 converter designs CLK24MHz CBUS0 24 MHz Clock output.** CLK12MHz CBUS0 12 MHz Clock output.** CLK6MHz CBUS0 6 MHz Clock output.** GPIO CBUS0 CBUS bit bang mode option. Allows up to 4 of the CBUS pins to be used as general purpose I/O. A separate application note, AN232R-01, available from FTDI website (www.ftdichip.com) describes in more detail how to use CBUS bit bang mode. BCD_Charger CBUS0 Battery Charge Detect indicates when the device is connected to a dedicated battery charger host. Active high output. NOTE: Requires a 10K pull-down to remove power up toggling. BCD_Charger# CBUS0 Active low BCD Charger, driven by an open drain to ground with no internal pull-up. BitBang_WR# CBUS0 Synchronous and asynchronous bit bang mode WR# strobe output. BitBang_RD# CBUS0 Synchronous and asynchronous bit bang mode RD# strobe output. VBUS_Sense CBUS0 Input to detect when VBUS is present. Time_Stamp CBUS0 Toggle signal which changes state each time a USB SOF is received Keep_Awake# CBUS0 Table 3 CBUS Configuration Control Description Active Low input, prevents the chip from going into suspend. * PWREN# must be used with a 10kΩ resistor pull up. **When in USB suspend mode the outputs clocks are also suspended. 5 Copyright © 2013 Future Technology Devices International Limited UMFT234XF Datasheet Version 1.0 Document Reference No.: FT_000818 Clearance No.: FTDI# 337 4.1 Configuring the MTP ROM The FT234XD IC on the module contains an embedded MTP ROM, this can be used to specify the USB descriptors, the functions of the CBUS0 pin, the current drive on each signal pin and the current limit for the device. These features can be programmed using FTDI’s programming utility FT_Prog. For details on using FT_Prog, please see the FT_PROG User Guide. When programming the MTP ROM please note: i) The Max Bus Power setting of the MTP ROM should specify the maximum current to be drawn from the USB host/hub when enumerated. For high-powered USB devices the current limit when enumerated is between 100mA and 500mA, for low-powered USB devices the current limit is 100mA. 6 Copyright © 2013 Future Technology Devices International Limited UMFT234XF Datasheet Version 1.0 Document Reference No.: FT_000818 5 Clearance No.: FTDI# Module Dimensions Measurements given in millimetres Tolerance of +/- 0.1mm Figure 1 UMFT234XF-01 Module Dimensions 7 Copyright © 2013 Future Technology Devices International Limited 337 UMFT234XF Datasheet Version 1.0 Document Reference No.: FT_000818 6 Clearance No.: FTDI# Module Circuit Schematic 6.1 UMFT234XF Schematic Figure 2 UMFT234XF Circuit Schematic 8 Copyright © 2013 Future Technology Devices International Limited 337 UMFT234XF Datasheet Version 1.0 Document Reference No.: FT_000818 7 Clearance No.: FTDI# 337 Environmental Compliances The UMFT234XF modules exclusively use lead free components, and are fully compliant with European Union directive 2002/95/EC. 9 Copyright © 2013 Future Technology Devices International Limited UMFT234XF Datasheet Version 1.0 Document Reference No.: FT_000818 8 Clearance No.: FTDI# 337 Internal MTP ROM Configuration Following a power-on reset or a USB reset the FT234XD will scan its internal MTP ROM and read the USB configuration descriptors stored there. The default values programmed into the internal MTP ROM in the FT234XD used on the UMFT234XF are in table 4. Parameter Value Notes USB Vendor ID (VID) 0403h FTDI default VID (hex) USB Product ID (PID) 6015h FTDI default PID (hex) Serial Number Enabled? Yes Serial Number See Note A unique serial number is generated and programmed into the MTP ROM during final test of the UMFT234XF module. Pull down I/O Pins in USB Suspend Disabled Enabling this option will make the device pull down on the UART interface lines when the power is shut off (PWREN# is high). Manufacturer Name FTDI Product Description UMFT234XF Max Bus Power Current 90mA Power Source Bus Powered Device Type FT234XD USB Version 0200 Returns USB 2.0 device description to the host. Note: The device is a USB 2.0 Full Speed device (12Mb/s). Remote Wake Up Enabled Taking RI# low will wake up the USB host controller from suspend. High Current I/Os Disabled Enables the high drive level on the serial and CBUS I/O pins. Load VCP Driver Enabled Makes the device load the VCP driver interface for the device. CBUS0 PWREN# Table 4 Default Internal MTP ROM Configuration The internal MTP ROM in the FT234XD can be programmed over USB using the utility program FT_PROG. FT_PROG can be downloaded from www.ftdichip.com. Users who do not have their own USB vendor ID but who would like to use a unique Product ID in their design can apply to FTDI for a free block of unique PIDs. Contact FTDI Support (support1@ftdichip.com) for this service. 10 Copyright © 2013 Future Technology Devices International Limited UMFT234XF Datasheet Version 1.0 Document Reference No.: FT_000818 9 Clearance No.: FTDI# 337 Contact Information Head Office – Glasgow, UK Branch Office – Oregon, USA Future Technology Devices International Limited Unit 1, 2 Seaward Place, Centurion Business Park Glasgow G41 1HH United Kingdom Tel: +44 (0) 141 429 2777 Fax: +44 (0) 141 429 2758 7130 SW Fir Loop Tigard, OR 97223-8160 USA Tel: +1 (503) 547 0988 Fax: +1 (503) 547 0987 E-mail (Sales) E-mail (Support) E-mail (General Enquiries) sales1@ftdichip.com support1@ftdichip.com admin1@ftdichip.com Branch Office – Taipei, Taiwan 2F, No. 516, Sec. 1, NeiHu Road Taipei 114 Taiwan, R.O.C. Tel: +886 (0) 2 8791 3570 Fax: +886 (0) 2 8791 3576 E-mail (Sales) E-mail (Support) E-mail (General Enquiries) tw.sales1@ftdichip.com tw.support1@ftdichip.com tw.admin1@ftdichip.com E-Mail (Sales) E-Mail (Support) E-Mail (General Enquiries) us.sales@ftdichip.com us.support@ftdichip.com us.admin@ftdichip.com Branch Office – Shanghai, China Room 1103, No. 666 West Huaihai Road, Shanghai, 200052 China Tel: +86 (0)21 6235 1596 Fax: +86 (0)21 6235 1595 E-mail (Sales) E-mail (Support) E-mail (General Enquiries) cn.sales@ftdichip.com cn.support@ftdichip.com cn.admin@ftdichip.com Web Site http://ftdichip.com Distributor and Sales Representatives Please visit the Sales Network page of the FTDI Web site for the contact details of our distributor(s) and sales representative(s) in your country. System and equipment manufacturers and designers are responsible to ensure that their systems, and any Future Technology Devices International Ltd (FTDI) devices incorporated in their systems, meet all applicable safety, regulatory and system-level performance requirements. All application-related information in this document (including application descriptions, suggested FTDI devices and other materials) is provided for reference only. While FTDI has taken care to assure it is accurate, this information is subject to customer confirmation, and FTDI disclaims all liability for system designs and for any applications assistance provided by FTDI. Use of FTDI devices in life support and/or safety applications is entirely at the user’s risk, and the user agrees to defend, indemnify and hold harmless FTDI from any and all damages, claims, suits or expense resulting from such use. This document is subject to change without notice. No freedom to use patents or other intellectual property rights is implied by the publication of this document. Neither the whole nor any part of the information contained in, or the product described in this document, may be adapted or reproduced in any material or electronic form without the prior written consent of the copyright holder. Future Technology Devices International Ltd, Unit 1, 2 Seaward Place, Centurion Business Park, Glasgow G41 1HH, United Kingdom. Scotland Registered Company Number: SC136640 11 Copyright © 2013 Future Technology Devices International Limited UMFT234XF Datasheet Version 1.0 Document Reference No.: FT_000818 Clearance No.: FTDI# 337 Appendix A - List of Figures and Tables List of Figures Figure 1 UMFT234XF-01 Module Dimensions ............................................................................................... 7 Figure 2 UMFT234XF Circuit Schematic........................................................................................................ 8 List of Tables Table 1 USB Connector Pin Out Description ................................................................................................ 4 Table 2 CBUS Configuration Control ............................................................................................................. 5 Table 3 Default Internal MTP ROM Configuration ...................................................................................... 10 Copyright © 2013 Future Technology Devices International Limited 9 UMFT234XF Datasheet Version 1.0 Document Reference No.: FT_000818 Clearance No.: FTDI# Appendix B: Revision History Document Title: UMFT234XF Document Reference No.: FT_000818 Clearance No.: FTDI# 337 Product Page: http://www.ftdichip.com/FT-X.htm Document Feedback: Send Feedback Version 1.0 Initial Datasheet Created Copyright © 2013 Future Technology Devices International Limited 09/04/13 10 337