6MBP50RA060_00

6MBP50RA060 IGBT-IPM R series Features · Temperature protection provided by directly detecting the junction temperature of the IGBTs · Low power loss and soft switching · High performance and high reliability IGBT with overheating protection · Higher reliability because of a big decrease in number of parts in built-in control circuit 600V / 50A 6 in one-package Maximum ratings and characteristics Absolute maximum ratings(at Tc=25°C unless otherwise specified) Item DC bus voltage DC bus voltage (surge) DC bus voltage (short operating) Collector-Emitter voltage INV Collector current Symbol Rating Min. VDC VDC(surge) VSC VCES DC IC 1ms ICP Duty=55.5% -IC Collector power dissipation One transistor PC Junction temperature Tj Input voltage of power supply for Pre-Driver VCC *1 Input signal voltage Vin *2 Input signal current Iin Alarm signal voltage VALM *3 Alarm signal current IALM *4 Storage temperature Tstg Operating case temperature Top Isolating voltage (Case-Terminal) Viso *5 Screw torque Mounting (M5) Terminal (M5) *1 Apply Vcc between terminal No. 3 and 1, 6 and 4, 9 and 7, 11 and 10. *2 Apply Vin between terminal No. 2 and 1, 5 and 4, 8 and 7, 13,14,15 and 10. *3 Apply VALM between terminal No. 16 and 10. *4 Apply IALM to terminal No. 16. *5 50Hz/60Hz sine wave 1 minute. *6 Recommendable Value : 2.5 to 3.0 N·m Unit V V V V A A A W °C V V mA V mA °C °C kV N·m N·m Max. 450 500 400 600 50 100 50 198 150 20 Vz 1 Vcc 15 125 100 AC2.5 3.5 *6 3.5 *6 0 0 200 0 0 0 0 -40 -20 - Fig.1 Measurement of case temperature Electrical characteristics of power circuit (at Tc=Tj=25°C, Vcc=15V) Item INV C ollector current at off signal input Collector-Emitter saturation voltage Forward voltage of FWD Symbol I CES V CE(sat) VF Condition VCE=600V input terminal open Ic=50A -Ic=50A Min. – – – Typ. – – – Max. 1.0 2.8 3.0 Unit mA V V 6MBP50RA060 Electrical characteristics of control circuit(at Tc=Tj=25°C, Vcc=15V) Item Power supply current of P-line side Pre-driver(one unit) Power supply current of N-line side three Pre-driver Input signal threshold voltage (on/off) Input zener voltage Over heating protection temperature level Hysteresis IGBT chips over heating protection temperature level Hysteresis Collector current protection level INV Over current protection delay time Under voltage protection level Hysteresis Alarm signal hold time SC protection delay time Limiting resistor for alarm *7 Switching frequency of IPM Symbol Iccp ICCN Vin(th) VZ TCOH TCH TjOH TjH IOC tDOC VUV VH tALM tSC RALM IGBT-IPM Condition Min. Typ. Max. fsw=0 to 15kHz Tc=-20 to 100°C *7 3 18 fsw=0 to 15kHz Tc=-20 to 100°C *7 10 65 ON 1.00 1.35 1.70 OFF 1.25 1.60 1.95 Rin=20k ohm 8.0 VDC=0V, Ic=0A, Case temperature, Fig.1 110 125 20 surface of IGBT chips 150 20 Tj=125°C 75 Tj=25°C Fig.2 10 11.0 12.5 0.2 1.5 2 Tj=25°C Fig.3 12 1425 1500 1575 Unit mA mA V V V °C °C °C °C A µs V V ms µs ohm Dynamic characteristics(at Tc=Tj=125°C, Vcc=15V) Item Switching time (IGBT) Switching time (FWD) Symbol Condition ton toff trr IC=50A, VDC=300V IF=50A, VDC=300V Min. 0.3 Typ. Max. 3.6 0.4 Unit µs µs µs Definition of tsc Thermal characteristics( Tc=25°C) Item Junction to Case thermal resistance Case to fin thermal resistance with compound INV IGBT FWD Symbol Rth(j-c) Rth(j-c) Rth(c-f) Typ. 0.05 Max. 0.63 1.33 Unit °C/W °C/W °C/W Recommendable value Item DC bus voltage Operating power supply voltage range of Pre-driver Switching frequency of IPM Screw torque Mounting (M5) Terminal (M5) Symbol VDC VCC fSW Min. 200 13.5 1 2.5 2.5 Typ. 15 Max. 400 16.5 20 3.0 3.0 Unit V V kHz N·m N·m 6MBP50RA060 Block diagram IGBT-IPM Pre-drivers include following functions a) Amplifier for driver b) Short circuit protection c) Undervoltage lockout circuit d) Over current protection e) IGBT chip over heating protection Outline drawings, mm Mass : 440g 6MBP50RA060 Characteristics (Representative) Control circuit IGBT-IPM 30 Power supply current vs. Switching frequency N-side Tj=100°C ········· P-side Input signal threshold voltage vs. Power supply voltage 2.5 Tj=25°C ········· Tj=125°C Power supply current Icc (mA) 25 2.0 20 Input signal threshold voltage Vin (ON), Vin (OFF), (V) 0 5 10 15 20 25 1.5 15 1.0 10 0.5 5 0 0 12 13 14 15 16 17 18 Switching frequency fsw (kHz) Power supply voltage Vcc (V) Undervoltage vs. Junction temperature 14 1.0 Undervoltage hysterisis vs. Junction temperature Undervoltage hysterisis VH (V) 12 0.8 10 Undervoltage VUVT (V) 8 0.6 6 0.4 4 0.2 2 0 20 40 60 80 100 120 140 0 20 40 60 80 100 120 140 Junction temperature Tj (°C) Junction temperature Tj (°C) Alarm hold time vs. Power supply voltage 3.0 200 Overheating characteristics TCOH,TjOH,TCH,TjH vs. VCC Alarm hold time tALM (msec.) 2.5 Overheating protection TCOH,TjOH (°C) OH hysterisis TCH,TjH (°C) 12 13 14 15 16 17 18 150 2.0 1.5 100 1.0 50 0.5 0 0 12 13 14 15 16 17 18 Power supply voltage Vcc (V) Power supply voltage Vcc (V) 6MBP50RA060 Inverter IGBT-IPM Collector current vs. Collector-Emitter voltage Tj=25°C 100 100 Collector current vs. Collector-Emitter voltage Tj=125°C 80 80 Collector current Ic (A) 60 Collector current Ic (A) 0 1 2 3 4 60 40 40 20 20 0 0 0 1 2 3 4 Collector-Emitter voltage VCE (V) Collector-Emitter voltage VCE (V) Switching time vs. Collector current Edc=300V, Vcc=15V, Tj=25°C Switching time ton, toff (nsec.) Switching time ton, toff (nsec.) Switching time vs. Collector current Edc=300V, Vcc=15V, Tj=125°C 1000 1000 100 100 0 10 20 30 40 50 60 70 80 0 10 20 30 40 50 60 70 80 Collector current IC (A) Collector current IC (A) Forward current vs. Forward voltage 100 Reverse recovery characteristics trr, Irr, vs. IF Reverse recovery current Irr (A) Reverse recovery time trr (nsec.) 0 1 2 3 4 80 100 Forward current IF (A) 60 40 20 10 0 0 10 20 30 40 50 60 70 80 Foeward voltage VF (V) Foeward current IF (A) 6MBP50RA060 Inverter IGBT-IPM Transient thermal resistance 500 450 1 400 Reverse biased safe operating area Vcc=15V, Tj