EDS10-15F

FC SERIES DATA SHEET SELF-BALANCING RECORDER PFA The FC SERIES self-balancing recorder is capable of continuously recording up to three types of inputs like process signal, DC voltage, current, thermocouple signal, resistance bulb signal, etc. Alarm units for the individual pens, external chart speed selector convenient for plant instrumentation, marking pen and many other optional accessories are prepared inside the self-balancing recorder. It is also usable as a trend recorder for 18 input points when combined with input selector (Type: PFC). FEATURES 1. Compact design measuring 96 mm wide by 144 mm high (front panel) by 400 mm deep (casing). 2. The recorder uses a folding type chart, of which one stack allows continuous recording for a month at a standard chart speed of 20 mm/h. 3. Data are indicated in bargraphs with color ribbon. 4. The servo-mechanism consists of a contactless induction potentiometer and a powerful coreless-motor, thereby assuring high reliability. 5. Chart speed is set accurately and can be switched easily by a combination of a clock circuit comprising a crystal oscillator and a pulse-motor. 6. The recorder can operate within a wide DC voltage range of 20 to 30V, or commonly at 50 and 60 Hz with an AC power supply. 7. The recording pen is a cartridge type felt-tip pen requiring a minimum of maintenance. SPECIFICATIONS Input signal: Process signal; 1 to 5V DC, 4 to 20mA DC DC voltage; 4mV span or more (30V max.) DC current; 100µA span or more (200mA max.) Thermocouple; 4mV span or more (Cold junction compensation, linearizer and burnout circuit built in.) Resistance bulb; Pt100 50 ° C span or more, 3wire system (linearizer built in) JPt100 in accordance with JIS C 1604-1981, 50 ° C span or more, 3wire system (linearizer built in) Slide rheostat; 10–100–10Ω, 3-wire system Input resistance and allowable signal source resistance: See page 3 Allowance: ± 0.5% of input span or ± 40 µV, whichever is larger Dead band: 0.2% of input span or 16 µV, whichever is larger Response time: Approx. 5 sec (variable within a range of approx. 2 to 20 sec) Number of recording points: 1, 2 or 3 pens Recording pens: Cartridge type felt-tip pen Pen No. 1 ... red, pen No. 2 ... green, pen No. 3 ... blue Scale length: 100mm (recording width) Chart length: 15m (continuous recording for 31 days at 20mm/h) Chart feed system: Pulse-motor type (driving pulse generator circuit built in) Chart storage system: Folding system Chart speed: 20mm/h basic (10, 30, 40, 60 and 120mm/h also selectable) Chart speed accuracy: ± 0.1% as measured on time axis on the chart EDS10-15f Date Aug. 31, 1994 PFA 24V (20 to 30V) DC or 100V ± 10%, 50/60Hz AC Power indicator lamp: Rectangular green LED Power consumption: Approx. 5.5W (24V DC) or approx. 8VA (100V AC) for 1-pen type Approx. 8W (24V DC) or approx. 12VA (100V AC) for 2-pen type Approx. 10W (24V DC) or approx. 15VA ( 100V AC) for 3-pen type Ambient temperature: Note: Temperature [°C] 0 to 45°C x humidity [% RH] Ambient humidity: 3000 30 to 90% RH Housing: Steel case External dimensions (HxWxD): 144x96x400mm (casing) + terminal board Mass{weight}(approx): 1-pen type; 5 kg 2-pen type; 5.5 kg 3-pen type; 6 kg Finish color: Munsell 7Y 7.3/1.4 (Case, front frame) Mounting: Panel flush-mounting Power supply: External selecting signal; Terminals F—F High speed selected by short circuited (Contact capacity; 5V, 10mA) Time marker; Recording of impulselike spike on lower end of chart at definite time intervals (2 min basic) Externally controlled marker; Operating only while terminals M—M are short circuited in external sequence. Contact capacity: 24V, 50mA Marking pen; Cartridge type felt-tip pen (blue) 2min 0% Marking unit: } 2min Low speed High speed Time marker ON OFF ON OFF Driven by external sequence α α=90° to 45° Indication pause: Indicator (recorder pen) is paused by short circuited terminals PS — PS via external sequence. (Contact capacity; 20V, 50mA) Note: Alarm device continues monitoring even while the indication is paused. Scope of delivery: Recorder, mounting bracket and standard accessories (see page 3) Specifications for optional units Alarm unit: Type; Comparator circuit type Upper limit + lower limit, two upper limits or two lower limits (for each pen) Setting accuracy; ± 1% of input span Hysteresis width; Approx. 0.4% of input span Output contacts; N.O (1a) contacts for upper limit and lower limit (excited at alarm condition) Contact capacity; Maximum voltage 125V AC/30V DC Current (breaking) Resistance load: 0.3A or less Relay load: 0.2A or less Note: Alarm output stabilized several seconds after turning ON power switch. If necessary, the user is to provide an external sequence such as a timer for cutting off output at start time. Chart speed selector: Selector; Internal switch or external sequence for selecting a preset low or high speed Low speed; 10, 20, 30, 40, 60, 120 mm/h High speed; 120, 300, 600, 1200, 3000, 6000,12000mm/h 2 Input resistance and allowable signal source resistance Es (Is) indicates input span (unit: mV or mA) Voltage input Input resistance 100kΩ or more Approx. 100kΩ Approx. 470kΩ 1 MΩ 1 MΩ Allowable signal source resistance 100Ω 100Ω 470Ω 1 kΩ 1 kΩ Current input Input resistance 50/Is Ω — 5Ω — 250 Ω List of chart Nos. (standard charts) Type Equal graduations (without graduation numerals) Graduation numeral — — — — — — Equal graduations (with graduation numerals) 0 to 40, 0 to 200 200 to 400 0 to 25, 50, 100 0 to 30, 60, 120 0 to 14, 0 to 70 700 to 1400 0 to 150, 50 to 200 100 to 250 0 to 80, 0 to 1600 800 to 1600 Number of Chart No. sections 40 50 60 70 75 80 40 50 60 70 75 80 FL-4000-S FL-5000-S FL-6000-S FL-7000-S FL-7500-S FL-8000-S FL-4001-S FL-5001-S FL-6001-S FL-7001-S FL-7501-S FL-8001-S Input Input 0.1 Is 10mA — 10