EDS3-1I

SAMPLING DEVICE SERIES FOR GAS ANALYZER DATA SHEET GAS EXTRACTOR (model: ZBA) Page 2 GAS FILTER GAS WASHING SEPARATOR AND WASHING NOZZLE SO3 MIST CATCHER (model: ZBB ) Page 6 PELTIER GAS COOLER (model: ZBC) GAS DRYER (model: ZBJ) (Semi-permeable membrane vapor phase dehumidifier) Page 9 FLOW METER AND REGULATOR (model: ZBD) Page 12 BALL VALVES AND SELECTOR VALVES (model: ZBF) Page 14 GAS ASPIRATOR (model: ZBG) Page 15 DRAININGS & OTHERS (model: ZBH) Page 16 GAS CONVERTER (model: ZDL) Page 18 STANDARD GAS (model: ZBM) Page 20 EDS3-1i Date Aug. 29, 2011 ■ GAS EXTRACTOR (model: ZBA) SPECIFICATIONS Type System Gas temperature ZBAK2 Electric heating (Standard type) 800°C max./SUS probe 1300°C max./SiC probe (Note 1) Electric heating system applicable to high temperature Amount of dust (guideline): Up to 100mg/N m 3 SUS316, Viton SUS 316, SiC JIS 5k 65AFF (Note 2) SUS316 mesh, Filtering capacity: 40µm 90% response at 3L/min: Approx. 25s 9kg (Excluding sampling pipe) Rc1/2 100V AC 100VA ZBAS1 Electric heating (Applicable to high dust) 800°C max./SUS probe Applicable to large amount of dust Amount of dust (guideline): Up to 20g/N m 3 ZBAB For cleaning gas extraction (Without filter) 100°C to 800°C (ZBAB0W) 100°C to 1000°C (ZBAB1T) Simple type intended for the environment relatively small in amount of dust Amount of dust (guideline): Up to 10mg/N m 3 SUS316, 304 (ZBAB0W) Titanium (ZBAB1T) SUS316, 304 (ZBAB0W) Titanium (ZBAB1T) JIS 5k 65AFF (ZBAB0W) JIS 5k 25AFF (ZBAB1T) — 90% response at 3L/min: Approx. 8s 3.5kg (Excluding sampling pipe) Rc1/2 — (Note 2) Features Material of part contacting gas Sampling pipe Companion flange Filter Response time (excluding sampling pipe) Mass (approx.) Sample gas outlet Heater Installation SUS316, Viton SUS 316 JIS 10k 50AFF (Note 2) SUS316 mesh, Filtering capacity: 10µm 90% response at 3L/min: Approx. 16s 20kg (Excluding sampling pipe) Rc1/2 100V AC 400VA Outdoor installation Note 1) The flow rate of sample gas should be kept at 1L/min. or lower for applications to high temperature gases. Contact us for applications to gases at flow rate higher than 1L/min. Note 2) Flange of other specifications are also available. Contact us for details. CODE SYMBOLS 12345678 9 10 1 1 ZBA B B K S 0W 1T 2W 1W Y A B C E G H J K D F 5- Description System (4th, 5th, and 6th digits) Unheated type, SUS Unheated type, titanium Electric heating type (Standard) Electric heating type (Applicable to high dust) Insertion length (L) (7th digit) 0mm 300mm L 400mm 600mm 800mm Gas temperature: 800°C max. (Material: SUS316) 1000mm 1200mm 1500mm 2000mm 700mm ZBAK gas temperature: 1300°C max. (Material: SUS, SiC) 900mm Gas output joint (9th digit) Nipple Current tap socket ZBAS: Specify this. Without Without ZBAB0: Specify either For ø10/ø8mm Teflon tube Without one of the two. Without With ZBAK For ø10/ø8mm Teflon tube With For ø10/ø8mm Teflon tube (Elbow) Without Flange (10th digit) JIS 5k 65AFF JIS 5k 25AFF Heating tube terminal support (11th digit) Without ZBAB0, 1: Specify this. With Details of selection *ZBAS: Specify one from Y to K. *ZBAB: Specify one from Y to G. *Material of ZBAB1: Titanium Gas temperature: 1000°C max. *ZBAK: Any one can be specified. 0 2 5 7 A A G Y A *ZBAS: Specify 0. *ZBAB0: Specify either 0 or 2. *ZBAB1: Specify A. *ZBAK: Specify one from 0, 2, 5, and 7 When 5 or 7 is . specified, the 11th digit is set to Y. A is unavailable. *ZBAS: Specify up to the 9th digit. (Not required) *ZBAB1: Specify G. *ZBAS: Specify up to the 9th digit. (Not required) *ZBAB0, 1: Specify Y. 2 OUTLINE (Unit: mm) ø155 Top Cover Heating tube support (when heating tube is provided) Terminal box Wiring port G1/2 (76) Rc 3/4 Flange JIS 5K 65AFF SUS316 Sampling pipe 20A ø27 Gas inlet Main nameplate Code for 7th digit Y: (Not supplied) A (300) G (1000) B (400) H (1200) C (600) J (1500) E (800) K (2000) Z: (By order) Code for 7th digit Y (Not supplied) D (700) F (900) 212 Rc 1/2 gas outlet Handle for filter replacement (750) 357 293 Packing Packing SiC sampling pipe ø30 ø130 ø155 4-ø15 Gas inlet Electric heating type (For high temperature application) (ZBAK2) (Rc1/2 with plug) Approx. 88 (600) 4-ø19 ø155 ø120 ø34 Sample Approx. 1003 120 280 16 Heater Thermostat Approx. 350 Lock 125 250 Gas outlet (Rc1/2) 300 Blow2 Blow1 14 Pipe Flange Terminal 3-Rc 1/2 Cable glands Approx. 216 Case Sample With ø10 teflon join Blow2 Packing Code for 7th digit C (600) E (800) G (1000) ø21.7 Gas inlet Cable Sampling pipe Cover 4–ø15 ø13 60 2-A15c For cable Approx. 177 2-A30a Blow1 0 ø155 Flange JIS 5K 65AFF (ZBAS1) (ZBAB0W) 3 Gas outlet joint Coupling for ø10/ø8 (internal diameter) Teflon tube 33 (67) 43 10 (300) (400) (600) (800) (1000) A B C E G : : : : : R1/2 Material: Teflon Code for 7th digit (For ZBAK, ZBAB0) ø10 Gas inlet RC1/2 4-ø12 32 ø8 R1/2 Material: Teflon Current tap socket Approx. 120 Approx. 47 ø75 Flange 95 R1/2 Rc1/2 (ZBAB1) (Unit: mm) Rc1/2 Material: Teflon SCOPE OF DELIVERY ZBAK2 : Main unit, sampling pipe, packing for flange × 1, bolt and nut × 4, O-ring (G50, G45) × 1 each or 2 each (for high temperature application) ZBAB : Main unit, sampling pipe, packing for flange × 1, bolt and nut × 4 ZBAS1 : Main unit, sampling pipe, packing for flange × 1, bolt and nut × 4, O-ring (G50) × 1, O-ring (G65) × 1 CONSUMABLE PARTS/SPARE PARTS Name Spare parts of ZBAK2 for 1 year (for general application) Spare parts of ZBAK2 for 1 year (for high temperature application) Spare parts of ZBAS1 for 1 year Wire mesh filter 40µm (for ZBAK2) O-ring (G50) (Pack of 10) O-ring (G45) (Pack of 10) Packing for wire mesh filter (Pack of 10) Coupling for ø10/ø8mm Teflon tube Order code ZBN5BA3 ZBN5BA4 ZBN3BA6 ZBNL1012 ZBNN1152 ZBNN1182 ZBNN1162 TK745559P1 TK745559P2 TK745559P10 Wire mesh filter 40µm × 1, O-ring (G50, G45) × 1 each, Packing for wire mesh filter × 1 Wire mesh filter × 1, O-ring (G50, G45) × 2 each, Packing for wire mesh filter × 2 Wire mesh filter 10µm × 2, O-ring (G50) × 4, O-ring (G65) × 4 For ZBAK1, 2 For ZBAK2, ABAS1 For ZBAK2 For ZBAK2 For ZBAK1 (R1/4) For ZBAK2, ABAB0 (R1/2) For ZBAB1 (R1/2 elbow) 4 31 (ø21.7) ø22 ø10 ø8 ■ GAS FILTER (model: ZBB) SPECIFICATIONS 1. Gas Filter Model Application Filter material Materials of gas-contacting parts Operating temperature Withstanding pressure Filter replacement Connection port Mass (approx.) Response time (at flow rate 1L/min) Pressure resistance ZBBB1V03-0 / ZBBB1V13-2 Primary filter for gas without drain Glass wool ZBBB2V03-0 For elimination of SO2 and SO3 Steel wool (Bonstar #0) (about 200 g) PVC (transparent) , chloroprene (O-ring) 0°C to 45°C 50kPa Required when about half of the filter element is contaminated by dust. Steel wool filter requires replacement when it is deteriorated. Gas inlet and outlet Rc 1/4 0.8 kg / 0.6 kg 1 kg About 30 sec for 90% indication About 0.1 kPa (at 5L/min) About 4 kPa (at 1L/min) At SO3 concentration of 30ppm: Replace once in 4 months (ZBBB3). Replace once in 8 months (ZBBB4). Hose end ø6, Upright attachment 0.1 kg / 0.3 kg ZBBB3V03-0 / ZBBB4V03-0 For elimination of SO3 Ceramic PVC (transparent) CONSUMABLE AND SPARE PARTS For 1-year analysis • ZBN3BB12 (for ZBBB1V03) Glass wool × 36, O-ring (G65) × 2 • ZBN3BBC2 (for ZBBB1V13) Glass wool × 12, O-ring (G65) × 2 • ZBN3BB22 (for ZBBB2V) Steel wool × 3, O-ring × 2 • ZBN3BB82 (for ZBBB3V) Replacement mist catcher × 3, Ancillary fitting × 1 • ZBN3BB92 (for ZBBB4V) Replacement mist catcher × 2, Ancillary fitting × 1 2. Membrane Filter Type Application Main materials of gas-contacting parts ZBBM2V 3-0 ZBBM6V03-0 ZBBM4V 3-0 Filter element: Teflon (ø55) O-ring : Chloroprene Body : PVC (transparent) Gas inlet and outlet Rc1/4 Gas inlet and outlet ø6.4 hose port ZBBM7V03-0 Final-stage filter and monitoring filter of analyzer Filter element: Glass fiber filter paper (ø55) O-ring : Chloroprene Body : PVC (transparent) Gas inlet and outlet Rc1/4 Gas inlet and outlet ø6.4 hose port : CODE 0 : general 1 : small volume type 2 : 30kpa pressure type 3 : 1+ 2 Connection port Operating temperature -10°C to 45°C 30 kPa (7th code 2 or 3) Withstanding pressure 5 kPa (7th code 0) Response for 90% indication Installation Mass Pressure resistance Approx. 3 sec (at 1L/min) with standard type (7th code 0) Approx. 1.5 sec (at 1L/min) with high speed type (7th code 1 or 3) On vertical panel face (gas inlet being bottom, outlet being top) Approx. 160 g Approx. 0.1 kPa (at 1L/min) Approx. 4.3 kPa (at 1L/min) CONSUMABLE AND SPARE PARTS Body type Part name Filter paper ZBNC6102 Fluoropore filter paper ZBN C6302 ZBBM2V ZBBM6V ZBBM4V ZBBM7V Remarks 100 sheet / 1 box 6 to 24 sheets /year 10 sheet / 1 box 12 to 50 sheet /year For 1-year analysis • ZBN3BB52 (for ZBBM2) Filter paper 25 sheets, O-ring G65 × 1, P49 x 1 • ZBN3BB72 (for ZBBM4) Fluoropore filter 12 sheets, O-ring G65 x 1, P49 x 1 • ZBN3BBA2 (for ZBBM6) Filter paper 25 sheets, O-ring G65 x 1, Rubber ring x 1 • ZBN3BBB2 (for ZBBM7) Fluoropore filter 12 sheets, O-ring G65 x 1, Rubber ring x 1 5 3. Mist filter Model Application ZBBK1V03-0 Drain separation, mist/dust removal, for general exhaust gas Glass fiber Cellulose Phenol resin Chloroprene PVC Double structure of approx. 40 and 5µm ZBBK2V03-0 ZBBK4V03-0 Drain separation, dust Same as left (with space removal, for SO2 analysis, for drain separation) for comparatively clean exhaust gas Polyethylene Chloroprene PVC approx. 5µm 0°C to 45°C Rc1/4 20kPa Approx. 200 cm 3 CONSUMABLE AND SPARE PARTS (1) Filter element • ZBNH2012 (for ZBBK2, 4) 2 pcs/set • ZBNH1002 (for ZBBK1) 1 pc./set • ZBNH2002 (for ZBBK2) 1 pc./set (2) O-ring (JISG65) • ZBNN1012 (For ZBBK1, 2, 4) (10 pcs/set) Main materials of gas-contacting parts Pore size Operating temperature Connection port Withstanding pressure Internal volume Response time Installation Mass Pressure resistance Inlet/outlet Rc1/4 Drain port: ø13 hose port Approx. 300 cm3 Approx. 7 sec Approx. 4 sec for 90% indication (at flow rate 5L/min) Vertical installation on wall face Approx. 0.6 kg Approx. 0.1 kPa (Dry) (flow rate 5L/min) Approx. 0.4 kPa (Wet) (flow rate 5L/min) (3) Requirement for 1 year (guideline when used for oil burning exhaust gas) • ZBN3BB32 (for ZBBK1) (Filter × 3, O-ring G65 × 2) • ZBN3BB42 (for ZBBK2, 4) (Filter × 3, O-ring G65 × 2) Approx. 0.35 kPa (flow rate 5L/min) Approx. 2.6 kPa (flow rate 5L/min) 4. Gas Washing Separator and Washing Nozzle Washing nozzle (ZBBH2 W03-0) Gas washing separator (ZBBF W03- ) Suction of dusty gas, washing with water and separation of water and gas Washing water: 100 to 200 kPa, Typically 5 to 10L/min depending on furnace pressure and sampling pressure loss Suction rate: Approx. 8L/min (water volume 8R/min, 160 mm water sealing, vertical piping of 1 m length) Ambient temperature: 0°C to 60°C Ambient temperature: 0°C to 60°C Connection port: Washing nozzle; Washing nozzle inlet Rc1/2 Gas inlet Rc11/4 Outlet Rc1/2 Blowback air inlet Rc1/2 Gas washing separator; Inlet R1/2 Gas outlet R1/2 Water outlet R1 Drain port Rc1/2 Main material of gas-contacting parts: SUS 316 Mass: Washing nozzle; approx. 3 kg Gas washing separator; approx. 15 kg (ZBBF2W) Discharge pressure: 2.1kPa at max. (When 2 is selected as the 5th digit of the code symbols) 5kPa at max. (When 5 is selected as the 5th digit of the code symbols) 2.1 to 6kPa (When 9 is selected as the 5th digit of the code symbols) Gas outlet coupling: None (When 0 is selected as the 9th digit of the code symbols) For ø10/ø8 mm Teflon tube (When 2, 3 is Model: Functions: selected as the 9th digit of the code symbols) Note: For washing, use the water that has undergone degassing processing. Otherwise indication error of O2 gauge (in the case of micro O2 gauge) of decrease of suction flow rate may result. Application Example Washing water Valve Washing nozzle (ZBBH2W) Gas extractor Blowback air inlet 1 m or longer vertical pipe required Avoid use of an elbow. Union R100 min. Gas outlet Water outlet Gas washing separator (ZBBF W) Drain The asterisked parts and pipes are optional parts. 6 OUTLINE ( Unit : mm ) 200 ø100 OUTLET 200 16 16 Space for filter replacement ø100 Space for filter replacement 80 INLET Gas outlet Rc1/4 2-ø7 mounting hole Gas inlet Rc1/4 OUTLET 10 30 50 25 55 This part is made of PVC (transparent) . 228 80 Gas outlet Rc1/4 2-ø7 mounting hole Rc1/4 Gas inlet Approx. 34 25 B 55 ø60 INLET Transparent A Drain port ZBBK1, 2 ZBBK4 36 54 160 212 DRAIN 105 A B ø60 Drain port DRAIN 100 30 Drain ø13 100 105 (ZBBK1,2) Rc1/4 (ZBBK4) Rc1/4 Mist filter (ZBBK) Gas filter (ZBBB1V03-0) (ZBBB2V03-0) ø100 16 200 Space for filter replacement Gas outlet 17 10 INLET 55 Gas inlet 25 55 30 18 C 150 80 2-ø7 mounting hole ø10/ø8 coupling for Teflon tube ø60 100 2-Rc1/4 Transparent B A Gas outlet OUTLET Gas inlet ø6 hose end (with cap) 105 A B C ø29 ø57 Gas filter (ZBBB1V13-2) ZBBB3 Approx. 242 ø22 ZBBB4 Approx. 272 ø48 SO3 Mist catcher (ZBBB3V) (ZBBB4V) 30 18 Mass 30 10 55 0.1kg 0.3kg 7 36 24.4 13.2 3 Gas outlet ø8 ø4.5 20 ø100 40 4-ø5 (or 4-M4) 2-ø25 hole UP 112 ø20 Gas inlet Rc1/4 28 60 Membrane filter (ZBBM2V, ZBBM4V) Panel mounting dimensions (ZBBM2V, ZBBM4V) Approx. 29 10 18 4-ø5 (or 4-M4) 2-ø25 hole ø6.4 Gas outlet 29.5 20 29.5 20 63.6 63.6 ø100 6 Gas inlet Membrane filter (ZBBM6V, ZBBM7V) Panel mounting dimensions (ZBBM6V, ZBBM7V) 28 20 60 R1/2 55 Approx. 120 Approx. 130 Gas+ water Gas outlet Rc1/2 Washing water inlet R1/2 Approx. L + 229 Approx. 200 108 102 4 60° Approx. 90 Blowback air inlet Rc1/2 To gas washing separator Rc1/2 4-ø10 mounting hole Rc1/2 Drain Ball valve 1/2 for water discharge 9th digit code 0, 1 and 2: Ball valve Approx. L + 271 Approx.132 L = 210 (ZBBF2W ) L = 500 (ZBBF5W ) L = as specified (ZBBF9W) Rc1/2 Drain 9th digit code 3: Ball valve Washing nozzle (ZBBH2W) Gas washing separator (ZBBF) 8 100 to 150 Water discharge 20 Sampling gas inlet Rc11/4 220 94 R1 ■ GAS DRYER, GAS COOLER (model: ZBJ / ZBC) SPECIFICATIONS 1. Gas dryer (Semi-permeable membrane vapor phase dehumidifier) Type ZBJ02503-72P Application ZBJ16253-48P Dehumidify sample gas such as flue gas or atmospheric air Measuring components SO2, NO, CO, CO2, O2, HC, H2, etc. Operating temperature -15°C to +80°C (No freezing allowed.) Mounting angle Not restricted Working pressure -0.04MPa to +0.5MPa (at 25°C) Material Polypropylene, Fluororesin, Viton -10°C or lower 0.5L/min. Approx. 0.8 kPa Approx. 12 cm3 Approx. 50 g PRINCIPLE OF GAS DRYER Wet sample gas Purge gas outlet Shell Dry sample gas Header Semi-permeable membrane tube Purge gas inlet Dehumidification dew point (Note) Standard flow rate Pressure resistance (at gas flow rate 1L/min) Internal volume (sample side) Mass -20°C or lower 1.0L/min. Approx. 2.8 kPa Approx. 20 cm3 Approx. 400 g The Gas dryer utilizes the characteristic of the semipermeable membrane tube that a certain component in a mixed gas is permeated from its higher partial pressure to the lower one. In the figure, the sample gas containing moisture is introduced through the inlet at the left end. Through the bottom right of the figure, the purge gas having a lower pressure and less moisture than the sample gas is injected. Then, moisture is removed from the wet sample gas due to the action of the semi-permeable membrane tube and discharged through the purge gas outlet. Thus, the sample gas is dried and becomes the dry sample gas to be discharged. (Note) Dehumidification conditions; Depend on the system in application example 2 under flow rate 0.5L/min, pressure 50 kPa and ambient temperature 20 to 22°C. Dehumidification Characteristic for Gas Dryer (typical example) Pressure: 0.05 MPa Ambient temperature: 20°C to 22°C 10 GAS DRYER Application example 1: When dry purge gas is supplied separately; Pressure gauge Sample Dehumidification dew point (°C) 0 ZB JO 25 -7 03 2P Flowmeter Purge gas Purge outlet Gas dryer –10 Sample gas P Drain separator Restrictor Drain bypass Pump –20 ZBJ16 253-4 8P –30 –40 0.5 1.0 1.5 2.0 Flow rate (L/min) 1) The purge outlet must be open to the atmosphere. 2) Although a higher sample pressure is preferable, it should normally be 0.1 MPa at maximum and atmospheric pressure at minimum. 3) The pressure gauge, when provided, is helpful for monitoring the operational status. 4) If drain occurs due to pressurization by the pump, it should partially be bypassed with the drain separator. 5) The volume of purge gas should be 2 to 5 times as large as that of sample gas. 9 Application example 2: When all volume of sample gas is usable for purge gas; Pressure gauge Filter F Flowmeter Analyzer Purge outlet Gas dryer Sample gas P Drain separator Restrictor Drain bypass 1) The purge outlet must always be open to the atmosphere. 2) A higher sample pressure is advantageous. The pressure should normally be 0.1 MPa at maximum and 0.05 MPa at minimum. If the pressure is low, an adequate dehumidification effect may not be obtainable. 3) The pressure gauge, when provided, is helpful for monitoring the operational status. 4) If drain occurs due to pressurization by the pump, it should partially be bypassed with the drain separator. Pump Caution on Use 1. Establish the flow path so dry gas flows on the face opposite to the semi-transparent face that contact the gas to be dried as shown by the example of use. 2. Dust should be removed by installing a filter of filtration accuracy 5µm or less before the dryer. Oil mist should also be disposed before the dryer. 3. If water drops enters the semi-permeable membrane tube, only the water permeates the membrane and the salts dissolved in the water are precipitated to cause clogging. Therefore, the flow path should be designed so as not to allow entrance of water drops. 4. This dryer has a large drying capacity and can reduce humidity, but cannot maintain humidity at a constant level by the ordinary usage. For using this dryer as a humidity conditioner, the flow rate, pressure and temperature need to be kept constant. 5. This dryer is unusable for gases of alcohol, ketone, and high-concentration ammonia, and those containing steam and NO 2 more than 100 ppm. OUTLINE ( Unit : mm ) Gas dryer Purge gas outlet Coupling for ø6.35 tube Inlet of gas to be dehumidified External cylinder tube (PP) Coupling for ø6.35 tube Purge gas inlet Coupling for ø6.35 tube ø6.35 28 Dry gas outlet Coupling for ø6.35 tube 1800 1890 Coupling (fluorocarbon polymers) Model : ZBJ02503-72P A B RC1/4 ø20 RC1/4 Coupling (fluorocarbon polymers) Coupling for ø6 tube Spring pin (SUS) Cap (PP) 2-RC1/4 ø38 86 Casing (PP) A APPROX. 714 1314 B APPROX. 600 1200 MASS APPROX. 250g 355g Model ZBJ16253-24P ZBJ16253-48P Model : ZBJ16253- 24 P 48 10 ø38 2. Peltier gas cooler Model System Flow rate (max.) (For constant dehumidification) (max.) Outlet gas dew point Short-time ripple Flow rate (max.) (For prevention of condensation) (max.) Dehumidification level check function Limit conditions Ambient temperature (max.) Inlet gas temperature (max.) Inlet gas dew point (max.) Main materials of gas-contacting parts Enclosure material Gas inlet/outlet Working pressure (max.) Ambient temperature Ambient humidity (max.) Power supply Power consumption (approx.) Mass (approx.) Scope of delivery ZBC91004 1-channel corrosion-proof type 1.5L/min ZBC92004 2-channel corrosion-proof type Parallel piping 1.5L/min (1-channel)×2 Series piping 3L/min 1°C to 3°C ±0.1°C 5.0L/min (dew point 0.5°C to 10°C) T thermocouple (built in) 10L/min (dew point 0.5°C to 10°C) 40°C 40°C 40°C Carbon, Fluoro rubber, Fluoro resin, HDPE, PVC SUS430 Rc1/4 60kPa 2°C to 40°C 90%RH 100V10V AC, 50/60Hz 140VA 4kg Body, spiral pulling out tool x 1 200VA 5kg (Note) Do not use gases containing organic solvent such as toluene, xylene, etc. OUTLINE ( Unit : mm ) Electronic gas cooler 1) Model: ZBC91004 Outlet Rc1/4 Inlet Rc1/4 41 38 50 50 2) Model: ZBC92004 Inlet A Outlet A Outlet B Inlet B 23 38 34 38 INLET A OUTLET A OUTLET B INLET B 6-Rc1/4 167 .4 162 50 6 17 10 202 182 161 11.4 167 .4 (20) 238 218 mounting hole 2×5.5 240 250 238 206 Power terminal Power terminal 255 245 C−C+ C−C+ Drain 5 41 mounting hole 4-ø5.5 8.5 Drain A 200 217 Drain B 5.5 Wiring diagram For internal connection + – H T G C+ C– V U G AC100V 50/60Hz output for T thermocouple 27.5 22 11 ■ FLOWMETETER, REGULATOR (model: ZBD) SPECIFICATIONS 1. Pressure Regulator Type ZBD61003 Right-hand thread for pressure adjustment of standard gas For general use (note) ZBD62003 Left-hand thread for pressure adjustment of standard gas For general use (note) ZBD63003 Right-hand thread for pressure adjustment of standard gas For corrosion prevention (note) ZBD64003 Left-hand thread for pressure adjustment of standard gas For corrosion prevention (note) Application Primary pressure Max. 14.7 MPa Max. 14.7 MPa Max. 14.7 MPa Max. 14.7 MPa Secondary pressure Variable from 0 to 0.12MPa Variable from 0 to 0.12MPa Variable from 0 to 0.15MPa Variable from 0 to 0.15MPa Standard gas container Standard gas container Right-hand 22/14 threads Left-hand 22/14 threads Gas outlet Rc 1/4 Gas outlet Rc 1/4 C3604 NBR 2.2 kg Standard gas container Standard gas container Right-hand 22/14 threads Left-hand 22/14 threads Gas outlet Rc 1/4 Gas outlet Rc 1/4 SUS316 Teflon 2.2 kg SUS316 Teflon 2.2 kg Connection Main materials of C3604 gas-contacting parts NBR Mass (approx.) Scope of delivery 2.2 kg Main unit and accessory (nylon packing for standard gas connection x 3) Main unit and accessory (Teflon packing for standard gas connection x 3) Note) Thread for connection with standard gas container: Right-hand thread when the specified combustible gas concentration of standard gas is less than 5% in total, and left-hand thread when it is 5% or more. Application: For general use; for other than corrosion prevention For corrosion prevention; When the specified gas concentration of standard gas is 1% CO or more (due to corrosion prevention) or when specifying corrosion prevention 2. Needle Valve Model Application Withstanding pressure 0.1MPa ZBD23003 ZBD24003 ZBD25003 Flow rate regulation 1.0MPa -10°C to 60°C Rc1/4 BSBM2 150 g Main unit SUS316 130 g 3. Relief Valve Model Application Settable pressure Ambient temperature Connection port Materials of gas-contacting parts Mass (approx.) ZBD35103 Sample gas and drain relief 40 to 60kPa 0°C to 45°C Rc1/4 PVC Viton rubber Hastelloy C 200 g Ambient temperature -10°C to 45°C Connection port Materials of gas-contacting parts Mass (approx.) Scope of delivery ø6 hose port PVC Viton rubber 100 g 4. Flow Meter Model Application Withstanding pressure Ambient temperature Connection port Materials of gas-contacting parts POM, hard glass, fluoro rubber 6th code ( Flow rate scale ) 1 : 0.1 to 1L/min 2 : 0.2 to 2L/min 3 : 0.5 to 5L/min 4 : 1 to 10L/min 5 : 2 to 20L/min 9 : As specified ZBD5 03 ZBD4 03 For general exhaust gas (metal joint unusable) For dangerous gas, corrosive gas (metal joint usable) 0.49MPa -10°C to 60°C Rc1/4 SUS304, hard glass, fluoro rubber (air, atmospheric pressure, 20°C) 5. Flow Checker Model Application Operating pressure ZBD71003 Flow rate monitoring Atmospheric pressure ZBD72003 Flow rate monitoring Atmospheric pressure Ambient -10°C to 60°C -10°C to 60°C temperature Connection port ø6 hose port ø6 hose port Material of Glass SUS316 Glass SUS316 part contact- Polyethylene Polyethylene Chloroprene ing gas Chloroprene Flow rate range Mass Scope of delivery White zone Yellow zone 0.3 to 0.7L/min 0.7 to 1.3L/min Approx. 100 g Approx. 100 g Main unit Main unit Flow regulating needle valve 5th code ( ) 2 : With needle valve (at inlet) 4 : With needle valve (at outlet){when pump is installed after it} 7 : Without needle valve 500 g Mass (approx.) 100 g 12 OUTLINE ( Unit : mm ) Outlet pressure indicator Inlet pressure indicator ZBD61 Pressure regulation handle Stop valve handle 110 ZBD62 Right-hand thread Left-hand thread W22-14 IN Cylinder packing (Dyfron) Rc1/4 12 Gas inlet ø70 78 91 Max . 114 Rc1/4 13 Gas outlet 30 Cylinder packing Connecting screw W22, 14 threads ZBD63 Right-hand thread ZBD64 Left-hand thread ø43 53 (Fully open) 9.5 55 (Fully open) 40 Gas inlet Rc1/4 Panel ø16.5 panel cutout, ø18 hole Gas outlet Rc1/4 Gas outlet Gas inlet Mounting screw 104 163 Rc1/4 OUT 82 173 L.P safety valve . Inlet pressure indicator H.P safety valve . Pressure regulator (ZBD61/ZBD62) Outlet pressure indicator 158 83 Stop valve handle 2–M5 Pressure regulation handle Relief valve (ZBD35) 188 Gas outlet Rc1/4 Pressure regulator (ZBD63/ZBD64) Mounting screw 2-M4 Panel 12 ø22 22 ø6 Gas outlet Panel cutout ø13 ø22.5 panel cutout, ø24 hole Gas outlet Rc1/4 18 ø43 14 30 18 Gas inlet ø6 18 30 18 2-ø4.5 Approx. 24 54 22 (Fully closed) 38 Needle valve (ZBD23) Rc1/4 Gas outlet Mounting hole 2–ø4.5 146 114 19 38 Needle valve (ZBD24) 13 Gas inlet Rc1/4 Needle valve (ZBD25) Top Mounting direction 38 (with needle valve on upper) Flow meter (ZBD44) 38 Ø18 31 34 5 Rc1/4 ø18 25 Gas inlet Flow meter (ZBD47) 28 32 5 Rc1/4 ø18 Approx. 23 (full open) (with needle valve on lower) 10 Max. 22 ø6 Gas outlet 25 2–ø24 Flow meter (ZBD42) Top Mounting direction Mounting screw 2-M4 25 Gas outlet 44 60 95 ø6 8 8 30 24 8 16 15.6 Gas inlet 112 30 ø22 ø18 2–ø4.5 Gas inlet Approx. 23 (full open) Rc1/4 Flow meter (ZBD57) Flow meter (ZBD52) Flow meter (ZBD54) Panel cutout (ZBD5) 13 25 2–M4 80 30 ■ Ball valves and selector valves (model: ZBF) SPECIFICATIONS Item Model Kind Ball valve ZBFB1003 ZBFB2003 ZBFB3003 ZBFB4003 General ball valve ZBFB1, 2; 2.0MPa ZBFB3, 4; 4.0MPa ZBFB1, 3 ; ZBFB2, 4 ; Rc1/2 Rc1/4 2-way valve 4-way valve 4-way valve ZBFH2003 ZBFH4003 ZBFH5003 Application Withstanding pressure Selection between sample Selection between sample Selection between sample gas and standard gas gas and standard gas gas and standard gas (for metal joint) 0.3MPa -10°C to 120°C Rc1/8 0.15MPa -5°C to 45°C Rc1/8 PVC Teflon 250g 0.5MPa -10°C to 80°C Rc1/4 SUS316 Teflon 500g Ambient temperature -10°C to 80°C Connection port Materials of gas-contacting parts Mass (approx.) ZBFB1, 2 ; Brass, Teflon SUS316 ZBFB3, 4 ; SUS316, Teflon Teflon 200g 230g OUTLINE ( Unit : mm ) ZBFB1, 3 : 60 ZBFB2, 4 : 80 ZBFB1, 3 : 19 ZBFB2, 4 : 26.5 ZBFB1, 3 : 40 ZBFB2, 4 : 54.6 ZBFB1, 3 : Rc1/4 ZBFB2, 4 : Rc1/2 (at both inlet and outlet) Ball valve (ZBFB) Handle fastening screw ZBFB1, 3 : 31 ZBFB2, 4 : 42 A M4 for removing knob 5-Rc1/4 (ZBFH5) 5-Rc1/8 (ZBFH4) 2-M4 25 ø28 36 ø50 ø30 49 M14 P=1 Locking pin ø3x2 12 Panel cutout, ø15 hole 72 B C ABC 22 38 70 19 41 73 40 Type ZBFH4 ZBFH5 Rc1/8 Gas inlet 36 2-ø4.5 hole Mounting dimensions 40 1 ø3 ho le ø18 ø32 2-way valve (ZBFH2) 4-way valve (ZBFH4/ZBFH5) 14 ■ GAS ASPIRATOR (model: ZBG) SPECIFICATIONS Model Materials of gas-contacting parts Power supply Max. vacuum Max. pressure (in continuous use) Max. EX-flow Mounting Ambient temperature Connection port Mass (approx.) (Discrimination) GA-380VF-DA Rc1/4 2.2kg GA-330V ZBG62004 ZBG52004 Diaphragm, valve: Viton Pump head: PP 100V±10V AC, 50/60Hz, approx. 50W Approx. -59.9kPa Approx. 98.0kPa Approx. 8L/10L/min Approx. -26.6kPa Approx. 29.4kPa Approx. 3L/3.6L/min 0°C to 40°C Rc1/8 1.7kg GS-3FD-F ZBG80004 Diaphragm, valve: Viton Pump head: PPS 100V±10V AC, 50/60Hz, approx. 30W Approx. -26.6kPa Approx. 29.4kPa Approx. 2.0L/min So as to set the motor shaft horizontal PERFORMANCE CURVE (at ambient temperature 20 ) [kPa] Discharge pressure 100 80 60 40 20 0 1234567 Discharge flow rate (L/min) Discharge pressure Discharge pressure Suction resistance 50Hz [kPa] 60Hz 0 {0} −13 −27 −40 [kPa] 50 Suction resistance 45 [kPa] 50Hz 0 40 60Hz 35 −13.3 30 −26.6 25 −39.9 20 15 10 5 0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 Discharge flow rate (L/min) [kPa] 50 40 30 20 10 0 1.0 2.0 3.0 Discharge flow rate (L/min) 50Hz 60Hz Suction resistance [kPa] 0 −7 −13 −20 ZBG5 ZBG6 73 58 22 INLET Rc 1/8 OUTLET Rc 1/8 12 OUTLINE ( Unit : mm ) OUTLET Rc 1/4 9.5 106 90 4-ø4.4 mounting hole Power terminal 19.5 Capacitor ZBG80 120 58 100 85 14.5 39 ø70 113 104 Nameplate INLET Rc 1/4 170 78 UL3266AWG22 Mount with this surface facing down. Ground terminal 102 E 133 E 84 7 9 90 78 （7） 4-ø4.4 ø4-7 (Mounting hole) 4-Rubber bush (accessories) ZBG52, ZBG62 ZBG80 SCOPE OF DELIVERY ZBG5, 6 main unit Accessories: Diaphragm Mounting tool Rubber foot ZBG main unit Accessories: Rubber foot 1 1 4 4 Usage and caution in use 1) Since aspiration pressure of the aspirator is large, be sure to install a safety drain trap for draining process before the aspirator to prevent drain from being sucked up. 2) The diaphragm and the valve should be replaced periodically. Be sure to allow space for the replacement above the pump head. (Space sufficient for attachment/detachment of screws with a driver, 150mm or larger, is required.) Consumable parts/spare parts For ZBG5 For ZBG6 For ZBG8 Diaphragm Valve ZBNG1012 (set of 5), Consumption: 1 to 2 pcs./year ZBNG1022 (set of 5), Consumption: 1 to 2 pcs./year Spare parts for 1 year (For ZBG5, ZBG6, and ZBG8) ZBN3BG52: Diaphragm × 2, Valve × 1 15 ■ DRAIN TRAP/POT/SEPARATOR (model: ZBH) SPECIFICATIONS 1. Safety Drain Trap 5. Bubbler Model: ZBH51603 Suction sample gas flow rate: Max. 3L/min Working pressure: -5.78kPa Water sealing: 0.98kPa Material: PVC (transparent) Ambient temperature: 1°C to 40°C Connection port size: Drain inlet ; Rc 1/4 Drain outlet ; Rc 1/4 Mass: Approx. 0.6 kg Model: ZBH65003 Gas outlet pressure: Approx. +3.7kPa Material: PVC (transparent) Ambient temperature: 1°C to 40°C Connection port size: Gas inlet/outlet Rc 1/4 Drain inlet/outlet Rc 1/4 Mass: Approx. 0.6kg Pump ZBG To analyzer Exhaust Peltier gas cooler ZBC 2. Drain Pot Model; Length ZBH13 03 255mm (ZBH130) 405mm (ZBH131) 650mm (ZBH133) Material: PVC (transparent) Ambient temperature: 1°C to 40°C Connection port size: Drain outlet Rc 1/4 ; Inlet ; ø39 Mass: Approx. 0.8kg (ZBH130) Drain discharge Bubbler ZBH65 Usage of Bubbler 6. Tank Model: ZBH41003 Internal volume: Approx. 1.5L Material: PVC (non-transparent) Ambient temperature: 1°C to 40°C Connection port size: Rc 1/4 Mass: Approx. 0.5kg 3. Sealed Drain Pot 0 ZBH3 03 10 Working pressure: 1.0 MPa (material SUS) 0.1 MPa (material PVC) Material: SUS304 or PVC (transparent) Ambient temperature : 1°C to 40°C Connection port size: Rc 1/4 Internal volume: 280 cc for material SUS 370 cc for material PVC Mass: Approx. 0.4kg (material PVC) Approx. 1.5kg (material SUS) Model: 7. Gas Conditioner Model: ZBH91003 Sample gas pressure: Approx. -3kPa to +3kPa Outlet gas pressure: Approx. +4.5kPa Materials: Main unit; PVC (transparent) Filter; Polyethylene O-ring; Chloroprene Pore size of filter: Approx. 5µm Ambient temperature: 1°C to 40°C Connection port size: Sample gas inlet ; Rc 3/8 Gas inlet/sample gas outlet ; ø6.5mm Drain outlet ; Rc 3/8 Drain inlet ; Rc 1/4 Mass: Approx.1.5kg 4. Drain Separator Model: ZBH81333 (1.1m dripping tube) ZBH81533 (1.3m dripping tube) Material: PVC (self-color) Ambient temperature: 1°C to 40°C Connection port size: Gas inlet/outlet Rc 1/2 (with joint for ø10 Teflon tube) Mass: Approx. 0.8kg CODE SYMBOLS (ZBH) 12345678 Z BH 3 Part name 1 1 1 1 3 3 3 3 3 3 3 3 0 0 1 1 0 1 3 9 0 9 0 9 0 0 0 0 0 0 0 0 Drain pot Description Application/specification Length 255mm Length 405mm Length 650mm Length as specified Material SUS 304, length L = 120mm Material SUS 304, length L = as specified (within 1m) Material PVC, length L = 200 mm Material PVC, length L = as specified (within 1m) Drain separation, PVC Buffer tank for paramagnetic oxygen analyzer CONSUMABLE AND SPARE PARTS Filter element for ZBH9 ZBNH2012 (2pcs/1set) O-ring for ZBH9 ZBNN1012 (10pcs/1set) JIS G65 Spare parts for 1 year for ZBH9 ZBN3BB42 Filter × 3, O-ring × 2 Sealed drain pot 3500 4100 5160 5190 6500 6590 8133 8153 9100 Demister Tank Safety drain trap Length X = 590mm, Y = 120mm Length X, Y specifiable (X + Y within 800mm) Bubbler Drain separator Gas conditioner Length L = 400mm Length L, specifiable With 1.1 m dripping tube (with joint for ø10mm tube) With 1.3 m dripping tube (with joint for ø10mm tube) Mist filter, safety drain trap and bubbler combined into integral body 16 OUTLINE ( Unit : mm ) Drain discharge port 40 10 ø60 ø39 hole 35 590(X) Rc1/4 Air inlet 10 15 2–Rc1/4 5 Drain inlet Rc1/4 Rc1/4 L L=255/ZBH130 L=405/ZBH131 L=650/ZBH133 L=by order/ZBH139 807 Drain outlet 120(Y) 21 ø22 10 ø61 Rc1/4 ø60 2–Rc1/4 L=120/ZBH300 L=by order/ZBH309 ø60 Rc1/4 L=200/ZBH310 L=by order/ZBH319 Drain pot (ZBH13 ) ø10/ø8 Teflon tube Joint (teflon) 2–Rc1/2 Safety drain trap (ZBH51) Gas inlet Gas outlet Sealed drain pot (ZBH30) 4–M4 ø95 Cartride filter 195 (ZBH31) 108 60 2–ø9 ZBH81333: Approx. 1250 ZBH81533: Approx. 1450 70 90 5 ø67 Approx. 34 ø22 Approx. 96 Rc1/2 Sample gas inlet Rc 3/8 Sample gas outlet Rc 1/4 30 142 X=690 1504 1450 Gas inlet ø6.5 Y=450 Drain outlet ø8.5 Drain inlet ø6.5 ø48 Drain separator (ZBH81) Gas inlet Exhaust 2-Rc1/4 80 30 With 1 plug Transparent Drain outlet L+150 Rc1/4 Gas conditioner (ZBH91) Rc1/4 inlet ø1 14 5 40 2-Rc1/4 Drain inlet 20 ø60 31 Approx. 137 L=400/ZBH650 L=by order/ZBH659 4-Rc1/4 outlet and inlet of exhaust gas from other analyzer L 270 240 210 Mounting hole 2-ø9 ø8 0 Bubbler (ZBH65) Tank (ZBH41) 200 L 17 ■ GAS CONVERTER (model: ZDL) SPECIFICATIONS 1. NO2/NO CONVERTER Type Mounting Target gas ZDL03001 ZDL04001 Indoor surface mounting Exhaust gas from general boilers/ atmosphere (Contact us for applications to gases other than those.) Usage: 2cm3 Replacement cycle: About 12 months (When O2 concentration reaches 5%, NO2 concentration 10ppm and flow rate 0.3L/min.) Temperature setting: 210±10°C (Detection terminal: K thermocouple) Built in Microcontroller X (Type: PXR4) Ceramic, Viton, glass filter, SUS316 90% or higher, Conforming to JIS 0.5L/min -5°C to +45°C 100V AC, 50/60Hz 100 to 240V AC, 50/60Hz Approx. 85VA 1.1kg 1.2kg Gases with dust and drain removed at 150°C or lower CE mark compliant Gas flow rate Ambient temperature Power supply Power consumption Mass Gas condition 2. CO/CO2 CONVERTER Type Mounting Target gas Catalyst ZDL21001 Indoor surface mounting Atmosphere (Contact us for applications for other gases.) Usage: 3cm3 Replacement cycle: About 6 months (Varies depending on usage conditions.) Temperature setting: 210±20°C (Detection terminal: K thermocouple) To be installed separately Microcontroller X (Type: PXR4) SUS316, Viton, glass wool 99% or higher (100ppm CO or lower) (Standard: 99.9%) Standard: 0.5L/min. or 1L/min. -5C to +45°C 100V AC, 50/60Hz Approx. 45VA Approx. 2kg Gases with dust and drain removed at 150C or lower Catalyst Temperature controller Material of part contacting gas Exchange efficiency Temperature controller Material of part contacting gas Exchange efficiency Gas flow rate Ambient temperature Power supply Power consumption Mass (approx.) Gas condition Overseas use STANDARD ACCESSORIES Converter type CO/CO2 catalyst (for 1 cycle) Glass wool ZDL03, 4 –– –– ZDL21 1 1 SPARE PARTS FOR 1-YEAR OPERATION Spare part model Converter type NO2/NO catalyst CO/CO2 catalyst Glass wool Catalyst fixture Joint 2 4 1 2 ZBN1DL72 ZDL03 1 ZBN1DL82 ZDL04 2 2 2 1 ZBN1DL42 ZDL21 18 OUTLINE ( Unit : mm ) [150] 135 Gas outlet ø9.5/ø5.5 148 135 124 130 Gas outlet ø9.5/5.5 SV SEL 78 220 PXR-4 4-ø5 Gas inlet ø9.5/ø5.5 Approx. 130 100V AC (shared with internal wiring) (NP) 105 160 PV (212) (12) C1 C2 AL1 AL2 AL3 105 [120] [210] Connection diagram (NP) LNE 27 4-ø5 Power terminal 100 to 240V AC Gas inlet ø9.5/5.5 110 Front view Right side view NO2/NO converter ZDL04001 NO2/NO converter ZDL03001 19 103 2.3 104 70 94 Gas outlet R3 13 ø9.5 Connection diagram ø1 1 8 K 12 3 4 5 270 CO/CO2 E converter 300 240 370 30 55 25 SSR Temperature controller AC 30 100V AC power supply 17 32 Gas inlet CO/CO2 converter ZDL21001 19 ■ STANDARD GAS (model: ZBM) CODE SYMBOLS 1. Pure Gas in volume of 3.4 or 10Lcylinder 1 2 3 4 5 6 7 8 9 10 Z BM Y04 1 3 AY BY EY KY LY MY PY SY NY TY 0 0 0 0 0 0 0 0 0 0 4 4 4 4 4 4 4 4 4 4 0 0 0 0 0 0 0 0 0 0 Cylinder size 10L 3.4L Component and application CO2 CO CH4 H2 Ar He NH3 O2 N2 (B) For general use N2 (A) Equivalent to zero gas for generation source with certification N2 (A) Zero gas for generation source with certification AIR (B) For general use AIR (A) Equivalent to zero gasfor generation source with certification AIR (A) Zero gas for generation source with certification Others 1 2 3 4 Connection thread Right-hand thread Left-hand thread Right-hand thread Left-hand thread Export certificate None None Provided Provided Description 2. 2-Component Mixture Gas in volume of 3.4 or 10Lcylinder 1 2 3 4 5 6 7 8 9 10 Z BM N 41 3 A B E K L M P S T U Z A B C D E F G H J K L M N P Z 0 1 2 1 2 3 4 Cylinder size 10L 3.4L Gas component and residual gas CO2 N2 CO N2 CH4 N2 H2 N2 Ar N2 He N2 NH3 N2 O2 N2 SO2 N2 NO N2 Other N2 Concentration 45 to 50ppm 90 to 100ppm 180 to 200ppm 225 to 250ppm 450 to 500ppm 900 to 1000ppm 1800 to 2000ppm 0.45% to 0.5% 0.9% to 1% 1.8% to 2% 4.5% to 5% 9% to 10% 18% to 20% 45% to 50% Other as specified With/without of specification None Approved class 1 standard gas for general use Approved class 2 standard gas for general use Connection thread Right-hand thread Left-hand thread Right-hand thread Left-hand thread Export certificate None None Provided Provided Description TY04 - 4 RY0 4 - 0 VY04 - 0 VY04 - 4 ZY04 - 0 3. Pure Gas in volume of 47Lcylinder 1 2 3 4 5 6 7 8 9 10 Z BM2 Y 0 4 QY 0 4 - 0 CY0 4 - 0 DY 0 4 - 0 DY 0 4 - 4 GY 0 4 - 0 HY 0 4 - 0 HY 0 4 - 4 ZY04 - 0 1 2 3 4 Description Description O2 N2 (B) For general use N2 (A) Equivalent to zero gas for generation source with certification N2 (A) Zero gas for generation source with certification AIR (B) For general use AIR (A) Equivalent to zero gas for generation source with certification AIR (A) Zero gas for generation source with certification Others Connection thread Right-hand thread Left-hand thread Right-hand thread Left-hand thread Export certificate None None Provided Provided 4. Canned Standard Gas in volume of 0.7Lcylinder Approx. 50 1 2 3 4 5 6 7 8 9 10 Z BM4 4 - 00 WY 0 NAG NZ Z Description Component and concentration N2 (B) CO2 1800 to 2000ppm/N2 Specified component/concentration (Contact Fuji.) OUTLINE ( Unit : mm ) øD, L Internal volume øD 140 140 L 965 425 10L 3.4L 15 6 øD Note1) Two-component mixed gas (3.4, 10L), Deviation Gas with class 1 certification :1% of labeled value Others :2% Valid term :1 year L Approx. weight [kg] Cap Note) Canned standard gas is available in dozen (12). Note2) Thread for connection (22/14 thread): Left-hand screw :lncluded 5% more combustible gas (except NH3) Right-hand screw :Other gases Caution on Safety *Before using this product, be sure to read its instruction manual in advance. International Sales Div Sales Group Gate City Ohsaki, East Tower, 11-2, Osaki 1-chome, Shinagawa-ku, Tokyo 141-0032, Japan http://www.fujielectric.com Phone: 81-3-5435-7280, 7281 Fax: 81-3-5435-7425 http://www.fjielectric.com/products/instruments/ Information in this catalog is subject to change without notice. Printed in Japan